QM26VNAF400-5M [BANNER]
QM26 and QMH26 Series Sensors;型号: | QM26VNAF400-5M |
厂家: | Banner Engineering |
描述: | QM26 and QMH26 Series Sensors |
文件: | 总16页 (文件大小:706K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
QM26 and QMH26 Series Sensors
Instrucꢀon Manual
Stainless Steel and Hygienic Stainless Steel Sensors for Washdown and Chemical Compaꢀbility
•
QM26: Washdown rated with convenient 25.4 mm (1 in) mounꢀng spacing and 3 mm (0.125 in)
mounꢀng hardware
•
•
•
•
•
•
•
•
QMH26: Hygienic shape for superior cleaning performance
Made from FDA compliant materials for worry-free use in food and pharmaceuꢀcal applicaꢀons
Chemically resistant, non-toxic 316L stainless steel housing
Acrylic opꢀcal window with coaꢀng for resistance to hydrogen peroxide and alcohol
IP69K rated for use in harsh 1500 psi washdown environments at 80° C (176° F)
Withstands environmental temperature cycling from –30° to +60° C (–22° to +140° F)
Sealed housing and smooth joints minimize cleaning ꢀme and reduce bacterial accumulaꢀon
Sensor marking is chemically etched into the housing for long-lasꢀng idenꢀꢁcaꢀon and to
eliminate food contaminaꢀon
•
•
Push buꢂons and light pipes are over-molded to reduce crevices and provide excellent cleaning
and sealing results
High performance coaxial polarized retroreꢃecꢀve models for clear or transparent boꢂle and ꢁlm
detecꢀon
•
•
•
Excellent background suppression performance with advanced ambient light suppression
Bright, visible red light spot on adjustable background suppression models makes alignment easy
Models have a hygienic design for easy cleaning and saniꢀzing
WARNING: Not To Be Used for Personnel Protecꢀon
Never use this device as a sensing device for personnel protecꢀon. Doing so could lead to serious injury or death.
This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety
applicaꢀons. A sensor failure or malfuncꢀon can cause either an energized or de-energized sensor output
condiꢀon.
QM26 Models
Stainless Steel Sensors for Washdown and Chemical Compaꢀbility
Model
Mode
Range
Output
Connector
QM26E-5M
5 m (16.25 ꢄ) cable, 4 wire
Emiꢂer
NA
QM26EQ5
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
QM26VNR-5M
QM26VNRQ5
QM26VPR-5M
QM26VPRQ5
QM26VNLP-5M
QM26VNLPQ5
QM26VPLP-5M
QM26VPLPQ5
QM26ENXLPC-5M
QM26ENXLPCQ5
QM26EPXLPC-5M
QM26EPXLPCQ5
Complementary
NPN
8.5 m (27.8 ꢄ)
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
Receiver
Complementary
PNP
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
Complementary
NPN
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
Polarized
Retroreꢃecꢀve
3 m (9.8 ꢄ) with
BRT-60X40C
Complementary
PNP
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
NPN
PNP
™
Expert Coaxial
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
2.6 m (8.5 ꢄ) with
BRT-60X40C
Polarized
Retroreꢃecꢀve
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
Original Document
166534 Rev. E
16 October 2017
166534
QM26 and QMH26 Series Sensors
Model
Mode
Range
Output
Connector
QM26VNAF400-5M
QM26VNAF400Q5
QM26VPAF400-5M
QM26VPAF400Q5
QM26VNAF200-5M
QM26VNAF200Q5
QM26VPAF200-5M
QM26VPAF200Q5
5 m (16.25 ꢄ) cable, 4 wire
Complementary
NPN
Adjustable Field
Background
Suppression
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
5 to 400 mm (0.2 in
to 15.7 in)
Complementary
PNP
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
Complementary
NPN
Adjustable Field
Background
Suppression (small
light spot) And
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
5 to 200 mm (0.2 in
to 7.85 in)
Complementary
PNP
200 mm (7.5 in) PVC pigtail, M12 Euro QD connector, 4-pin
QMH26 Models
Hygienic Stainless Steel Sensors for Washdown and Chemical Compaꢀbility
Model
Mode
Range
Output
Connector
QMH26VNLP-5M
QMH26VNLPQ7
5 m (16.25 ꢄ) cable, 4 wire
M8 Pico QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
M8 Pico QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
M8 Pico QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
M8 Pico QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
M8 Pico QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
M8 Pico QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
M8 Pico QD connector, 4-pin
5 m (16.25 ꢄ) cable, 4 wire
M8 Pico QD connector, 4-pin
Complementary NPN
Polarized Retroreꢃecꢀve
3m (9.8 ꢄ) with BRT-60X40C
QMH26VPLP-5M
QMH26VPLPQ7
Complementary PNP
NPN
QMH26ENXLPC-5M
QMH26ENXLPCQ7
QMH26EPXLPC-5M
QMH26EPXLPCQ7
QMH26VNAF400-5M
QMH26VNAF400Q7
QMH26VPAF400-5M
QMH26VPAF400Q7
QMH26VNAF200-5M
QMH26VNAF200Q7
QMH26VPAF200-5M
QMH26VPAF200Q7
™
Expert Coaxial Polarized
2.6 m (8.5 ꢄ) with BRT-60X40C
5 to 400 mm (0.2 in to 15.7 in)
5 to 200 mm (0.2 in to 7.85 in)
Retroreꢃecꢀve
PNP
Complementary NPN
Complementary PNP
Complementary NPN
Complementary PNP
Adjustable Field Background
Suppression
Adjustable Field Background
Suppression (small light spot)
Overview
QMH26
QM26
Key
3
3
1. Green Indicator
1
1
2
2
2. Yellow Indicator
4
3. Push Buꢂon
4
Adjustment Screw/Potenꢀometer (not shown)—AFxxx
models
4. Opꢀcal Window
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 166534 Rev. E
QM26 and QMH26 Series Sensors
Sensor Installaꢀon
Install the sensor so that the object to be detected moves horizontally to the sensor.
Wiring Diagrams
Wiring Key
1 = Brown
1
3
4
1
3
4
+
+
10-30V dc
–
10-30V dc
–
2 = White
3 = Blue
4 = Black
Load
Load
2
2
Remote
Programming
Remote
Programming
™
™
Expert NPN
Expert PNP
3
1
1
3
1
3
4
2
–
+
+
10-30V dc
–
10-30V dc
+
10-30V dc
–
Beam
Enable
4
4
Load
Load
N.C.
2
2
Load
Load
QM26—Emiꢁers
NPN
PNP
Sensor Conꢂguraꢀon
•
•
•
Adjustable ꢁeld background suppression models (AFxxx models) have an 8-turn adjustment screw (potenꢀometer) to set the
background suppression distance.
™
Expert coaxial polarized retroreꢃecꢀve models (XLPC models) are conꢁgurable using either the sealed push buꢂon or the
remote input wire.
Two-lens polarized retroreꢃecꢀve models (LP models) and opposed mode models require no user adjustments.
Sensor Setup - Background Suppression—AFxxx Models
Background Suppression Mode: Objects beyond the set cutoff distance will not be detected.
Background suppression mode can be used in most situaꢀons with varying object colors and posiꢀons or with varying background
condiꢀons.
To ensure reliable background suppression, a minimum separaꢀon distance between the object and the background is necessary. See
Figure 5 on page 10 to determine the minimum separaꢀon distance.
P/N 166534 Rev. E
www.bannerengineering.com - Tel: +1-763-544-3164
3
QM26 and QMH26 Series Sensors
1. Mount the sensor with the darkest object at the longest applicaꢀon
distance. The distance to the object must be less than shown in
Figure 5 on page 10 for your object color.
Object
Background
2. Turn the adjustment potenꢀometer counter-clockwise unꢀl the
X
yellow indicator turns off (8 turns maximum).
3. Turn the adjustment potenꢀometer clockwise unꢀl the yellow
indicator turns on.
Y
4. Replace the darkest object with the brightest background at the
Cutoff
Distance
closest applicaꢀon distance.
5. Turn the adjustment potenꢀometer clockwise, counꢀng the
revoluꢀons, unꢀl the yellow indicator turns on.
6. Turn the adjustment potenꢀometer counter-clockwise half of the
number of turns from step 5. This places the cutoff distance midway
between the object and the background switchpoints (see Figure 1
on page 4).
X: Distance to the Object
Y: Minimum Separaꢀon Between the Object and
the Background
The sensor is ready for operaꢀon.
Figure 1.
Set the cutoff distance approximately midway
between the farthest object and the closest
background
Setup Example
An object with a reꢃecꢀvity similar to black paper is set 100 mm (3.9 in) away
from the AF200 sensor. A background with a reꢃecꢀvity similar to white paper
is set away from the sensor. According to Figure 5 on page 10 , the minimum
separaꢀon distance between the object and the background is 24 mm (0.94 in).
In this applicaꢀon, reliable detecꢀon is achieved when set up according to the
procedure outlined in Sensor Setup - Background Suppression—AFxxx Models
on page 3.
2
3
1
Y
X
Figure 2. Background Suppression Mode Applicaꢀon
Example
1. Object
2. Conveyor
3. Background
X: Distance to the Object = 100 mm (3.9 in)
Y: Minimum Separaꢀon Between the Object and
the Background = 24 mm (0.94 in)
Remote Conꢂguraꢀon—XLPC models
The remote input wire (pin 2/white wire) is used to to lock the push buꢂon, select Light or Dark Operate, or perform the desired Light
™
SET or Dark SET for the object. In contrast to other Banner Engineering sensors, the QM26 and QMH26 Expert coaxial polarized
retroreꢃecꢀve sensors (XLPC models) use the duraꢀon between pull-high pulses on the remote input wire to both iniꢀate the Light SET
or Dark SET and to select the desired sensiꢀvity simultaneously. See Light SET for High Sensiꢀvity on page 5, Light SET for Medium
Sensiꢀvity on page 6, and Dark SET for Maximum Operaꢀng Range on page 7 for details.
Note: Aꢄer the delay before startup has elapsed ( ≤ 300 ms), the remote input may be used.
Push Buꢁon Lockout—XLPC Models
The remote input wire (pin 2/white wire) can be used to disable the sensor push buꢂon on the XLPC models to prevent unauthorized
adjustment to the sensor. Connect the remote input wire (pin 2/white wire) of the sensor to the +V dc terminal to disable conꢁguraꢀon
adjustments using the push buꢂon.
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 166534 Rev. E
QM26 and QMH26 Series Sensors
Push Buꢁon
Not available
Not available
Remote Input Wire
Result
Connect the remote input wire to +V dc for 4 ms or longer.
Disconnect the remote input wire from +V dc.
The push buꢂon is disabled (locked).
The push buꢂon is enabled (unlocked).
Select Light Operate/Dark Operate—XLPC models
Change the sensor operaꢀon to light operate or dark operate for the desired applicaꢀon. Use either the buꢂon or the remote input wire
procedure to conꢁgure the sensor.
Push Buꢁon
Remote Input Wire
Result
Push buꢁon only: The green LED ꢃashes.
Press and hold the buꢂon for longer
than 12 s.
Pulse the remote input wire to +V dc, then pull the
remote input wire to ground for 2000 to 3000 ms.
Conꢀnue pressing the buꢂon unꢀl the
desired operaꢀon is selected, then
release the buꢂon.
Light operate select: Pulse the remote input wire to +V
dc for 4 to 1000 ms, then pull the remote input wire to
ground.
LED
LED
Yellow
OFF
Green
Flashing
+Vdc
> 12 sec.
t Teach Input
2000 ... 3000 ms
tp light
4 .. 1000 ms
L.O.
0
t
Yellow LED ON = Light operate
t = 0
Dark operate select: Pulse the remote input wire to +V
dc for 1000 to 2000 ms, then pull the remote input wire
to ground.
LED
LED
Yellow
ON
Green
Flashing
+Vdc
t Teach Input
2000 ... 3000 ms
tp dark
1000 .. 2000 ms
D.O.
0
t
t = 0
Yellow LED OFF = Dark operate
LED
LED
Yellow
OFF
Green
Flashing
The sensor is conꢁgured for the desired mode
and is ready.
Light SET—XLPC Models
A Light SET opꢀmizes the sensor to provide reliable detecꢀon of
various objects. For most applicaꢀons, the factory default seꢅng
is appropriate. Perform the Light SET only if the desired object is
not reliably detected. Stable mounꢀng of both the sensor and
the reꢃector is required for reliable detecꢀon.
Sensor positions
threshold ≈ X % below
the presented condition
•
High sensiꢀvity (11% offset)—suitable for highly
transparent boꢂles, thin ꢁlms, and foils. See Light SET
for High Sensiꢀvity on page 5.
Output ON
Output OFF
•
Medium sensiꢀvity (18% offset)—suitable for standard
boꢂle types and translucent objects. See Light SET for
Medium Sensiꢀvity on page 6.
Single
Darkest
Most Light
(saturated
signal)
Presented
Condition
(no signal)
Figure 3. Light SET (Dark Operate Shown)
Light SET for High Sensiꢀvity
Use High Sensiꢀvity (11% sensiꢀvity) for detecꢀng highly transparent boꢂles, thin ꢁlms, and foils with a thickness of more than 20 µm.
Use either the buꢂon or the remote input wire procedure to conꢁgure the sensor.
P/N 166534 Rev. E
www.bannerengineering.com - Tel: +1-763-544-3164
5
QM26 and QMH26 Series Sensors
Push Buꢁon
Remote Input Wire
Result
Clear the light path to the reꢃector.
Clear the light path to the reꢃector.
Press the buꢂon for 2 to 7 seconds unꢀl
the LEDs ꢃash simultaneously, then
release the buꢂon.
Push buꢁon only: The green and yellow LEDs
ꢃash simultaneously.
Pulse the remote input wire to +V dc, then pull the
remote input wire to ground for 4 to 1000 ms.
Pulse the remote input wire to +V dc to complete the
high sensiꢀvity Light SET.
LED
LED
Yellow
2 to 7 sec.
Green
+Vdc
SIMULTANEOUS
Flashing at
3Hz
t Teach
4 ... 1000 ms
0
t
t = 0
The sensor is conꢁgured for High Sensiꢀvity and
is ready for use.
Light SET for Medium Sensiꢀvity
Use Medium Sensiꢀvity (18% sensiꢀvity) for detecꢀng standard boꢂle types and translucent objects. Use either the buꢂon or the
remote input wire procedure to conꢁgure the sensor.
Push Buꢁon
Remote Input Wire
Result
Clear the light path to the reꢃector.
Clear the light path to the reꢃector.
Press the buꢂon for 7 to 12 seconds
unꢀl the LEDs ꢃash alternately, then
release the buꢂon.
Push buꢁon only: The green and yellow LEDs
ꢃash alternately.
Pulse the remote input wire to +V dc, then pull the
remote input wire to ground for 1000 to 2000 ms.
Pulse the remote input wire to +V dc to complete the
medium sensiꢀvity Light SET.
LED
LED
Yellow
7 to 12 sec.
Green
+Vdc
ALTERNATELY
Flashing at
3Hz
t Teach
1000 ... 2000 ms
0
t
t = 0
The sensor is conꢁgured for Medium Sensiꢀvity
and is ready for use.
Dark SET—XLPC Models
Dark SET (maximum operaꢀng range) is the factory default
seꢅng and provides maximum sensing range, ease of
alignment, and reliable detecꢀon of brown or green boꢂles
and opaque objects.
Sensor positions threshold
above the present condition
for max. operating range
Output ON
Output OFF
Single
Presented
Condition
Most Light
(no signal)
Darkest
(saturated
signal)
Figure 4. Dark SET (Dark Operate Shown)
6
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 166534 Rev. E
QM26 and QMH26 Series Sensors
Dark SET for Maximum Operaꢀng Range
Use either the buꢂon or the remote input wire procedure to conꢁgure the sensor.
Push Buꢁon
Remote Input Wire
Result
Block the light path to the reꢃector.
Block the light path to the reꢃector.
Press the buꢂon for 2 to 7 seconds unꢀl
the LEDs ꢃash simultaneously, then
release the buꢂon.
Push buꢁon only: The green and yellow LEDs
ꢃash simultaneously.
Pulse the remote input wire to +V dc, then pull the
remote input wire to ground for 4 to 1000 ms.
Pulse the remote input wire to +V dc to complete the
Dark SET.
LED
LED
Yellow
2 to 7 sec.
Green
+Vdc
t Teach
4 ... 1000 ms
SIMULTANEOUS
Flashing at
3Hz
0
t
t = 0
The sensor is conꢁgured for Dark SET (maximum
operaꢀng range).
Clear the light path to the reꢃector.
Clear the light path to the reꢃector.
The sensor is ready for use.
P/N 166534 Rev. E
www.bannerengineering.com - Tel: +1-763-544-3164
7
QM26 and QMH26 Series Sensors
Speciꢂcaꢀons
Supply Voltage and Current
Output Response Time
10 to 30 V dc (10% maximum ripple within speciꢁed limits); supply current
(exclusive of load current) < 20 mA
500 µs
Repeatability
QM26—Opposed Models: 110 μs
All other models: 150 μs
Note: For UL applicaꢀons: For use in class 2 circuits
only.
Indicators
Supply Protecꢀon Circuitry
Green on: Power ON and sensor ready
Protected against reverse polarity and transient voltages
Yellow on: Light sensed
XLPC models—Yellow flashing: Light sensed but marginal signal
Output Conꢂguraꢀon
XLPC models: Single PNP or NPN on pin 4 (black wire) with remote input on pin
Construcꢀon
2 (white wire)
Housing: 316L stainless steel
Opꢀcal Window: Coated acrylic (PMMA)
Indicator and buꢁons: TPV - PE
All other models: Complementary PNP or NPN by model number
Delay Before Power-Up
< 300 ms
Connecꢀon
Output Raꢀng
4-wire 5 m (16.25 ꢄ) cable or 4-pin M12 Euro-style quick disconnect connector
with 200 mm (7.5 in) PVC pigtail, depending on model
100 mA per output
Banner recommends using the 4-Pin Threaded M12/Euro-Style Cordsets—
Washdown, Stainless Steel cordsets listed in the Accessories secꢀon.
Off-state leakage current for load = 1500 Ω:
NPN: < 200 μA
PNP: < 500 μA
Note: These proximity switches shall be used with
UL Listed Cable assemblies rated 30 V, 0.24 A
minimum, in the ꢁeld installaꢀon.
ON-state saturaꢀon voltage: < 2 V at 100 mA
Output Protecꢀon Circuitry
Protected against false pulse at power up, and overload or short circuit of
outputs
Adjustments
QM26 Emiꢁer—Beam Enable: Connect black wire to +V dc to acꢀvate emiꢂer
Emiꢁer LED Wavelength
AF200 models: 660 nm
All other models: 620 nm
LED
AFxxx models—Adjustment Screw: Sets background suppression distance
XLPC models—Push Buꢁon: User set up
XLPC models—Remote Input Wire: Remote PLC set up and push buꢂon lock
out
Required Overcurrent Protecꢀon
WARNING: Electrical connecꢀons must be made
by qualiꢁed personnel in accordance with local
and naꢀonal electrical codes and regulaꢀons.
Environmental Raꢀng
IEC IP67 and IEC IP69K
Chemical Compaꢀbility
Overcurrent protecꢀon is required to be provided by end product applicaꢀon
per the supplied table.
®
ECOLAB cerꢀꢁed
Operaꢀng Condiꢀons
Overcurrent protecꢀon may be provided with external fusing or via Current
Limiꢀng, Class 2 Power Supply.
Operaꢀng Temperature and Storage Temperature: –30 °C to +70 °C (–22 °F to
+158 °F)
Supply wiring leads < 24 AWG shall not be spliced.
For addiꢀonal product support, go to www.bannerengineering.com.
Note: UL cerꢀꢁed in the temperature range –30 °C
to +55 °C (–22 °F to +131 °F).
Supply Wiring (AWG)
Required Overcurrent Protecꢀon (Amps)
Humidity: Periodic exposure to 100% humidity and washdown cleaning
20
22
24
26
28
30
5.0
3.0
2.0
1.0
0.8
0.5
Vibraꢀon and Shock
IEC60947-5-2
Cerꢀꢂcaꢀons
with class 2 power supply
8
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 166534 Rev. E
QM26 and QMH26 Series Sensors
QM26 Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
QMH26 Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
P/N 166534 Rev. E
www.bannerengineering.com - Tel: +1-763-544-3164
9
QM26 and QMH26 Series Sensors
Performance Curves
Minimum Separaꢀon Distance
AF200 Models
AF400 Models
90
80
70
60
50
40
30
20
10
0
Black/ White
40
Black/ White
35
30
25
20
15
10
5
Gray / White
Gray / White
White / White
White / White
Object / Background
0
Object / Background
0
50
100
150
200
250
0
100
200
300
400
500
90% White Card Cutoff Setting (mm)
90% White Card Cutoff Setting (mm)
Figure 5. Minimum Separaꢀon Distance
Minimum Sensing Range
AF200 Models
AF400 Models
15
10
5
15
10
5
0
0
0 5
50
100
150
200
250
0 5
100
200
300
400
500
90% White Card Cutoff Setting (mm)
90% White Card Cutoff Setting (mm)
Figure 6. Minimum Sensing Range (Dead Zone)
10
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 166534 Rev. E
QM26 and QMH26 Series Sensors
Excess Gain
1000
100
10
1
1
10
100
1000
10000
DISTANCE (mm)
Figure 7. Opposed Mode Models
100
BRT-60x40C
BRT-92x92C
BRT-40x19A
BRT-60x40IP69K
BRT-THG-2-100 (2” x 2”)
BRT-60x40C-PS
BRT-40x19A-PS
10
1
1
10
100
1000
10000
DISTANCE (mm)
™
Figure 8. Expert Retroreꢁecꢀve Models (XLPC Models)
100
BRT-60x40C
BRT-92x92C
BRT-40x19A
BRT-60x40IP69K
BRT-THG-2-100 (2” x 2”)
BRT-60x40C-PS
BRT-40x19A-PS
10
1
1
10
100
1000
10000
DISTANCE (mm)
Figure 9. Fixed Gain Retroreꢁecꢀve Models (LP models)
P/N 166534 Rev. E
www.bannerengineering.com - Tel: +1-763-544-3164
11
QM26 and QMH26 Series Sensors
AF200 Models
AF400 Models
1000
1000
100
10
Setpoint: 15 mm
Setpoint: 200 mm
Setpoint: 400 mm
Setpoint: 15 mm
Setpoint: 100 mm
Setpoint: 200 mm
1000
100
10
1
1
1
10
100
1000
1
10
100
1000
DISTANCE (mm)
DISTANCE (mm)
Figure 10. Adjustable Field Models (AFxxx Models)
Beam Paꢁerns
100
80
60
40
20
150
100
50
0
0
-20
-40
-60
-80
-100
-50
-100
-150
0
1000
2000
3000
4000
5000
0
1000 2000 3000 4000 5000 6000 7000 8000 9000
DISTANCE (mm)
DISTANCE (mm)
Figure 12. Fixed Gain Retroreꢁecꢀve (LP) Models
Figure 11. Opposed Mode Models
60
40
20
0
-20
-40
-60
0
500
1000
1500
2000
2500
3000
3500
DISTANCE (mm)
Figure 13. Expert Retroreꢁecꢀve Models (XLPC ) Models
™
12
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 166534 Rev. E
QM26 and QMH26 Series Sensors
AF200 Models
AF400 Models
8
6
6
4
4
2
2
0
0
-2
-4
-6
-8
-2
-4
-6
0
50
100
150
200
250
0
100
200
300
400
DISTANCE (mm)
DISTANCE (mm)
Figure 14. Adjustable Field Models (AFxxx Models)
Spot Size Versus Distance
Clear Object Expert Retroreflecꢀve (XLPC) Models
100 x 100
80 x 80
60 x 60
40 x 40
20 x 20
0 x 0
0
50
100
150
200
250
300
DISTANCE (mm)
Accessories
Cordsets for QM26 Models with Suffix Q5
All measurements are listed in millimeters, unless noted otherwise.
4-Pin Threaded M12/Euro-Style Cordsets (Washdown, Stainless Steel) (Recommended)
Cable: PVC cable, stainless steel coupling nut, EPDM o-ring
Conductors: 22 AWG, gold-plated contacts
Voltage/Current Raꢀng: 300 V dc, 4.0 A
Temperature: –40 °C to +105 °C (–40 °F to +221 °F)
Environmental Raꢀng: IEC IP69K
4-Pin Threaded M12/Euro-Style Cordsets—Washdown, Stainless Steel
Model
Length
Style
Dimensions
Pinout (Female)
MQDC-WDSS-0406
MQDC-WDSS-0415
1.83 m (6 ꢄ)
4.57 m (15 ꢄ)
2
3
1
4
Ø15.5 mm
Straight
Ø4.8 mm
MQDC-WDSS-0430
9.14 m (30 ꢄ)
1 = Brown
2 = White
3 = Blue
43.5 mm
4 = Black
P/N 166534 Rev. E
www.bannerengineering.com - Tel: +1-763-544-3164
13
QM26 and QMH26 Series Sensors
4-Pin Threaded M12/Euro-Style Cordsets
Cable: PVC jacket, PUR (polyurethane) connector body, nickel-plated brass coupling nut
Conductors: 22 AWG, gold-plated contacts
Conductors: 22 AWG, gold-plated contacts
Voltage/Current Raꢀng: 250 V ac/dc, 4.0 A
Temperature: –40 °C to +105 °C (–40 °F to +221 °F)
Environmental Raꢀng: IP67/IP69K
4-Pin Threaded M12/Euro-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
MQDC-406
MQDC-415
MQDC-430
1.83 m (6 ꢄ)
4.57 m (15 ꢄ)
9.14 m (30 ꢄ)
2
3
1
4
44 Typ.
Straight
M12 x 1
ø 14.5
1 = Brown
2 = White
3 = Blue
MQDC-450
15.2 m (50 ꢄ)
4 = Black
Cordsets for QMH26 Models with suffix Q7
All measurements are listed in millimeters, unless noted otherwise.
4-Pin Threaded M8/Pico-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
PKG4M-2
PKG4M-5
2 m (6.56 ꢄ)
5 m (16.4 ꢄ)
35 Typ.
Straight
ø 9.5
PKG4M-9
9 m (29.5 ꢄ)
4
3
2
1
M8 x 1
PKW4M-2
PKW4M-5
2 m (6.56 ꢄ)
5 m (16.4 ꢄ)
28 Typ.
1 = Brown
2 = White
3 = Blue
20 Typ.
Right Angle
4 = Black
PKW4M-9
9 m (29.5 ꢄ)
M8 x 1
ø 9.5
Brackets for QM26 Models
All measurements are listed in millimeters, unless noted otherwise.
SMBLSTDLQ26
SMBLSTQ26
15
15
•
Adjustable right-angle
metal bracket
•
•
Right-angle bracket
304 stainless steel
•
304 stainless steel
72
35
15
32
Brackets for QMH26 Models
All measurements are listed in millimeters, unless noted otherwise.
14
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 166534 Rev. E
QM26 and QMH26 Series Sensors
SMBQMH26-SS-150
ø 12
150
•
•
•
Smooth surfaces for easy
cleaning
ø 22
Setscrew adjustment of
sensor
316L stainless steel
Retroreflectors
All measurements are listed in millimeters, unless noted otherwise.
BRT-60X40C
BRT-92X92C
•
•
•
Rectangular, acrylic target
Reꢃecꢀvity Factor: 1.4
Temperature: –20 °C to +60 °C (–4 °F
to +140 °F)
Opꢀonal brackets are available
Approximate size: 40 mm × 60 mm
•
•
•
Square, acrylic target
Reꢃecꢀvity Factor: 3.0
Temperature: –20 °C to +60 °C (–4 °F to
+140 °F)
Opꢀonal brackets are available
Approximate size: 92 mm × 92 mm
•
•
•
•
BRT-40X19A
BRT-60X40IP69K
•
•
•
Rectangular, acrylic target
Reꢃecꢀvity Factor: 1.3
Temperature: –20 °C to +60 °C (–4 °F to
+140 °F)
•
Rectangular, acrylic target (color is
amber)
•
•
Reꢃecꢀvity Factor: 0.7
Temperature: –20 °C to +140 °C (–4 °F
to +284 °F)
•
Approximate size: 19 mm × 60 mm
overall; 19 mm × 40 mm reꢃector
•
•
•
•
Chemically resistant
IP69K washdown rated
Opꢀonal brackets are available
Approximate size: 40 mm × 60 mm
BRT-60X40C-PS
BRT-40X19A-PS
•
•
•
Rectangular, polystyrene target
Reꢃecꢀvity Factor: 1.1
Temperature: –20 °C to +60 °C (–4 °F
to +140 °F)
•
•
•
Rectangular, polystyrene target
Reꢃecꢀvity Factor: 1.0
Temperature: –20 °C to +60 °C (–4 °F to
+140 °F)
•
•
Opꢀonal brackets are available
Chemically compaꢀble with hydrogen
peroxide
Yellow back
Approximate size: 40 mm × 60 mm
•
Chemically compaꢀble with hydrogen
peroxide
•
•
Yellow back
Approximate size: 19 mm × 60 mm
overall; 19 mm × 40 mm reꢃector
•
•
Model
Reflecꢀvity Factor
0.7
Maximum Temperature
Size
BRT-THG-2-100
+60 °C (+140 °F)
50 mm (2 in) wide, 2.5 m (100 in) long
P/N 166534 Rev. E
www.bannerengineering.com - Tel: +1-763-544-3164
15
QM26 and QMH26 Series Sensors
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture which, at the ꢀme it is returned to the factory, is found to have been defecꢀve during the warranty period. This warranty does not cover
damage or liability for misuse, abuse, or the improper applicaꢀon or installaꢀon of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discreꢀon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY
OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT
DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaꢀons or liabiliꢀes relaꢀng to any product previously
manufactured by Banner Engineering Corp. Any misuse, abuse, or improper applicaꢀon or installaꢀon of this product or use of the product for personal protecꢀon applicaꢀons when the
product is idenꢀꢁed as not intended for such purposes will void the product warranty. Any modiꢁcaꢀons to this product without prior express approval by Banner Engineering Corp will void the
product warranꢀes. All speciꢁcaꢀons published in this document are subject to change; Banner reserves the right to modify product speciꢁcaꢀons or update documentaꢀon at any ꢀme.
Speciꢁcaꢀons and product informaꢀon in English supersede that which is provided in any other language. For the most recent version of any documentaꢀon, refer to:
www.bannerengineering.com.
©
Banner Engineering Corp. All rights reserved
相关型号:
©2020 ICPDF网 联系我们和版权申明