MQDEC-430SS-PUR [BANNER]
K50 Pro Touch Button with IO-Link;型号: | MQDEC-430SS-PUR |
厂家: | Banner Engineering |
描述: | K50 Pro Touch Button with IO-Link |
文件: | 总8页 (文件大小:520K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
K50 Pro Touch Button with IO-Link
Datasheet
50 mm IO-Link Controlled Multicolor RGB Touch Button
•
•
•
IO-Link gives full access to color, flashing, rotating, and dimming settings as well as
advanced animations such as dynamic sequence mode and LED control
Touch and output settings, including on and off delays, touch sensitivity, output function, and
output state are also available with IO-Link
Excellent immunity to false triggering by water spray, detergents, oils, and other foreign
materials
•
•
•
Vibration feedback models available for an unmistakable touch confirmation
Rated IEC IP67 and IP69K per DIN 40050-9
Ergonomically designed to eliminate hand, wrist, and arm stresses associated with repeated
switch operation; no physical force required to operate
Standard Model
•
•
•
•
18 V dc to 30 V dc operation
Can be actuated with bare hands or gloves; adjustable sensitivity
Compact models available for lower profile applications
Models constructed from FDA-grade materials available
Compact Model
WARNING:
•
•
•
Do not use this device for personnel protection
Using this device for personnel protection could result in serious injury or death.
This device does not include the self-checking redundant circuitry necessary to allow its use in
personnel safety applications. A device failure or malfunction can cause either an energized (on) or de-
energized (off) output condition.
Models
Activation
Family
K50
Style
P
Method
Housing
C
Control
K
Connector
QP
T
T = Touch
TF = Touch, FDA-grade
TV = Touch, Vibration Feedback
P = Pro
C = Compact*
Blank = Standard Dome
K = IO-Link
Q** = 4-pin integral M12/Euro-style quick disconnect
QP = 150 mm (5.9 in) PVC cable with 4-pin
M12/Euro-style quick disconnect
TFV = Touch, FDA-grade, Vibration Feedback
** Not available in FDA-grade material
* Not available in FDA-grade material or with vibration feedback
Models with a quick disconnect require a mating cordset
Wiring Diagram
Key
3
1
1 = Brown
18–30 V dc
IO-Link
2 = White
3 = Blue
4 = Black
4
2
Communication
Not used
Original Document
208737 Rev. C
24 May 2019
208737
K50 Pro Touch Button with IO-Link
®
IO-Link
®
IO-Link is a point-to-point communication link between a master device and a sensor and/or light. It can be used to automatically
parameterize sensors or lights and to transmit process data. For the latest IO-LINK protocol and specifications, please visit
www.io-link.com.
For the latest IODD files, please refer to the Banner Engineering Corp website at: www.bannerengineering.com.
IO-Link Process Data In (Device to Master)
Use process data to read the device output state. When the device is in Four State Full Logic mode, use process data to read the
device logic state in addition to the output state.
Name
Description
Output State
Device State
Output state follows touch input
Current state (State 1, State 2, State 3, State 4). Only available with Operation Mode set to Four State Full Logic or
Multicolor
IO-Link Process Data Out (Master to Device)
Use process data out to define device states. Use parameter data to define device modes, states, touch settings, output settings,
vibration feedback, and custom colors.
Advanced Mode
Use process data to control delays, color, intensity, flash, and other animation types. Process data is also used to control the
sequence value dynamically. Use parameter data to create custom colors, intensity, speeds, and to define output and touch
settings.
Four State Full Logic Mode
Use process data to define the Job Input state and to read the touch state and device state (State 1, State 2, State 3, State 4).
See below for more information about how to achieve legacy logic types (C, D, E, and H). Use parameter data to change color,
intensity, flash, speed, select animation type, and define output settings.
Multicolor Mode
Use process data to activate the defined device state. Use parameter data to define output settings, control delays, color,
intensity, flash, and other animation types for State 1, State 2, State 3, and State 4.
Definitions for device states in Advanced Mode, Four State Full Logic Mode, and Multicolor Mode
Name
Description
Animation Type
Off
Indicator is off
Steady
Flash
Color 1 is solid on at defined intensity
Color 1 flashes at defined speed, color intensity, and pattern
Color 1 and Color 2 flash alternately at defined speed, color intensities, and pattern
Two Color Flash
50/50
Color 1 is displayed on 50% of the indicator and Color 2 is displayed on the other 50% of the indicator at the defined
color intensities
50/50 Rotate
Chase
Color 1 is displayed on 50% of the indicator and Color 2 is displayed on the other 50% of the indicator while rotating at
the defined speed, color intensities, and rotational direction
Color 1 is displayed as a single spot against the background of Color 2 while rotating at the defined speed, color
intensities, and rotational direction
Intensity Sweep
Color Sweep
Sequence
Color 1 repeatedly increases and decreases intensity between 0% to 100% at defined speed and color intensity
Color 1 and Color 2 transition alternately at defined speed and color intensities
Color 1 increments against the background of Color 2 at defined Dynamic or Static Sequence Value (Advanced mode and
other modes respectively)
Animation Direction
Animation Pattern
Defines the direction of rotation for the 50/50 rotate, chase, and sequence animations (CW or CCW)
Defines the flash pattern for flash and two color flash animations (normal, strobe, three pulse, SOS, or random); also
defines the pattern of the vibration feedback
Animation Speed
Defines the animation speed (slow, medium, fast, or custom); also defines the speed of the vibration feedback pattern
Defines the type of vibration response when the button is touched (Off, On, Animation Pattern)
Vibration Feedback
2
www.bannerengineering.com - Tel: + 1 888 373 6767
P/N 208737 Rev. C
K50 Pro Touch Button with IO-Link
Definitions for device states in Advanced Mode, Four State Full Logic Mode, and Multicolor Mode
Name
Description
Off Delay Type
Defines if the Off Delay should be measured from when the conditions for the State began (Leading Edge) or from when
the conditions ended (Trailing Edge)
Off Delay (ms)
The duration of the animation Off Delay. Leading Edge Off Delays can be used to ensure the animation is active for at
least a minimum amount of time.
Dynamic/Static Sequence Value
Defines the span of Color 1 in the Sequence animation [0-255]. 0 means no portion of the animation will be Color 1, and it
increases in a circular manner to 255 which indicates the full circumference will be Color 1. In Advanced Mode, this is in
process data and is called Dynamic Sequence Value. In the other modes, this is in parameter data and is called Static
Sequence Value.
Sequence Shift
Shifts the beginning of the sequence animation to the specified LED (LED1 at 12 o'clock continuing in the direction
indicated by the Animation Direction parameter
Color 1
Defines Color 1 of defined animation
Color 1 Intensity
Color 2
Defines the intensity of Color 1 in the animation (high, medium, low, off, or custom)
Defines Color 2 of defined animation
Color 2 Intensity
Defines the intensity of Color 2 in the animation (high, medium, low, off, or custom)
Four State Full Logic Mode State Descriptions
Use process data job input and the touch button input to dictate which one of these states the device should be in. Use
parameter data to define the state characteristics.
State 1: Process Data job input off and touch inactive
State 2: Process Data job input on and touch inactive
State 3: Process Data job input off and touch active
State 4: Process Data job input on and touch active
Legacy Logic Definitions (Four State Full Logic)
Four State
C Logic
D Logic
E Logic
H Logic
State 1 is Off. State 2 is Color 1/Job Input. State 3 is Color 2/Acknowledge. State 4
is defined the same as State 3
No Touch
Touch
Full Logic
No Input
Job Input
State 1 is Off. State 2 is Color 1/Job Input. State 3 is Off. State 4 is defined the
same as State 2
State 1
State 2
State 3
State 4
State 1 is Off. State 2 is Color 1/Job Input. State 3 is Color 2/Mispick. State 4 is
defined the same as State 2
State 1 is power, defined as Color 1. State 2 is defined the same as State 1. State 3
is Color 2/Sense. State 4 is defined the same as State 3
LED Control Mode
Use process data to define the color and intensity of each individual LED. Use parameter data to define customer colors and
intensities. LED1 is oriented at the 12 o'clock position continuing clockwise through LED8 near 11 o'clock position.
Name
Description
LED 1 Color….LED 8 Color
LED 1 Intensity…LED 8 Intensity
Vibration Feedback
Defines the color of the designated LED.
Defines the intensity of the designated LED [Values: 0-10]
Defines the type of vibration response when the button is touched (Off, On, Pattern)
Defines the pattern of the vibration feedback (normal, strobe, three pulse, SOS, or random)
Defines the speed of the vibration feedback pattern (slow, medium, fast, or custom)
Vibration Pattern
Vibration Speed
Demo Mode
Cycles through color spectrum, 50/50 rotate, intensity sweep, and sequence mode. Touch speeds cycle rate up or down (can
be either Momentary or Latching). Touch initiates state showing individually colored LEDs. When set to demo mode, the device
will cycle through the defined sequence when power is applied regardless of its connection to an IO-Link master.
Touch Settings
Use Parameter Data to define the following settings.
P/N 208737 Rev. C
www.bannerengineering.com - Tel: + 1 888 373 6767
3
K50 Pro Touch Button with IO-Link
Setting
Description
Touch Sensitivity
Defines the sensitivity of the touch button as either Standard, High or Low. Low sensitivity resists false activation. High
sensitivity can be used for improved touch response
Function
Latching or Momentary Options. Momentary function toggles output on only during a touch input. Latching function
toggles output on or off for each touch input
Mute Enable
Turning on mute disables the touch input
On Delay (ms)
Length of time the button needs to be pressed to trigger a touch active state. 0-60,000 ms
Output Settings
Use Parameter Data to define the following settings.
Setting
Description
Output State
Off Delay Type
Off Delay (ms)
Normally Open or Normally Closed. Normally Open turns the output on with a touch input. Normally Closed turns the
output off with a touch input
Leading Edge or Trailing Edge. Leading Edge delays will begin once a touch has been sensed. Trailing edge delays will
begin once the touch has been released
Length of time before the output state returns to a touch inactive state after the button has been released. 0-60,000 ms
Specifications
Supply Voltage
Default Indicator Characteristics
18 V dc to 30 V dc
Dominant
Wavelength (nm) or
Color Temperature
(CCT)
Color
Lumen
Output
Supply Current
1
Coordinates
Color
132 mA maximum current at 18 V dc (exclusive of load)
93 mA maximum current at 24 V dc (exclusive of load)
82 mA maximum current at 30 V dc (exclusive of load)
(Typical at
2
x
y
25 °C)
Green
Red
522
620
576
466
5700K
493
–
0.154
0.689
0.477
0.140
0.328
0.170
0.379
0.556
0.515
0.388
0.155
0.616
0.217
0.177
0.700
0.309
0.493
0.054
0.337
0.340
0.172
0.420
0.220
0.561
0.247
0.370
0.089
0.536
16.5
8.3
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Yellow
Blue
23.8
4.6
Touch Dwell Time
If touch dwells for longer than 60 seconds, the output will revert to the
untouched state
White
25.1
18.4
11.1
15.7
9.1
Vibration Feedback Characteristics
Max Total On-Time Per Touch: 3 seconds
Mechanical Life: 500,000 cycles
For all touch conditions, the default Vibration Feedback is On and the type
of vibration feedback is Steady
Cyan
Magenta
Amber
Rose
589
–
Response Time
Input Response: 5 ms minimum
Touch Response: 300 ms maximum (Standard Sensitivity touch response)
Lime Green
Sky Blue
Orange
Violet
562
486
599
–
21.4
19.5
12.1
9.7
Operating Conditions
–40 °C to +50 °C (–40 °F to +122 °F)
Humidity: 90% at +50 °C maximum relative humidity (non-condensing)
Storage: –40 °C to +70 °C (–40 °F to +158 °F)
Spring
Green
508
17.0
Environmental Rating
Standard Models: IEC IP67, IP69K per DIN 40050-9
QP models also meet IP69K per DIN 40050-9 if the cable and cable
entrance are protected from high-pressure spray
FDA Models: IEC IP67, IP69K per DIN 40050-9
Mounting
M30 × 1.5 threaded base, maximum torque 4.5 N·m (40 in·lbf)
1
2
Refer to the CIE 1931 (x,y) Chromaticity Diagram to show equivalent color with indicated color coordinates. Actual coordinates may differ 5%.
Values shown apply to dome models only. Compact models are 20% lower.
4
www.bannerengineering.com - Tel: + 1 888 373 6767
P/N 208737 Rev. C
K50 Pro Touch Button with IO-Link
Construction
Required Overcurrent Protection
WARNING: Electrical connections must be
Standard Model Base, Dome, and Nut: Polycarbonate
FDA Model Base, Dome, and Nut: FDA-grade copolyester
made by qualified personnel in accordance with
local and national electrical codes and
regulations.
Vibration and Mechanical Shock
Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 1.0 mm
amplitude, 5 minutes sweep, 30 minutes dwell)
Meets IEC 60068-2-27 requirements (Shock: 30G 11 ms duration, half sine
wave)
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via Current
Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.
Connections
Integral 4-pin M12/Euro-style quick disconnect or 150 mm (5.9 inch) PVC
cable with a M12/Euro-style quick disconnect, depending on model
Models with a quick disconnect require a mating cordset
Supply Wiring (AWG)
Required Overcurrent Protection (Amps)
IO-Link Interface
Supports Smart Sensor Profile: No
20
22
24
26
28
30
5.0
3.0
2.0
1.0
0.8
0.5
Baud Rate: 38400 bps (COM2)
Process Data In: 16 bits (2 bytes)
Process Data Out: 80 bits (10 bytes)
IODD Files: Provides all programming options, plus additional functionality
Certifications
(Vibration Feedback
models are not UL
listed.)
Dimensions
Standard Models
Compact Models
35 mm
[1.38”]
55 mm
[2.17”]
17 mm
[0.67”]
37.0 mm
[1.46”]
48.0 mm
[1.89”]
66 mm
[2.6”]
M30 x 1.5
Ø50 mm
[1.97”]
Ø50 mm
[1.97”]
M12 x 1
All measurements are listed in millimeters [inches], unless noted otherwise.
Accessories
Cordsets
4-Pin Threaded M12/Euro-Style Cordsets—Double Ended
Model
Length
Style
Dimensions
Pinout
MQDEC-401SS
MQDEC-403SS
MQDEC-406SS
MQDEC-412SS
MQDEC-420SS
MQDEC-430SS
0.31 m (1 ft)
0.91 m (3 ft)
1.83 m (6 ft)
3.66 m (12 ft)
6.10 m (20 ft)
9.14 m (30 ft)
Female
2
3
1
4
40 Typ.
[1.58"]
M12 x 1
Male
ø 14.5 [0.57"]
Male Straight/
44 Typ.
[1.73"]
Female Straight
1
4
2
3
M12 x 1
ø 14.5 [0.57"]
MQDEC-450SS
15.2 m (50 ft)
1 = Brown
2 = White
3 = Blue
4 = Black
P/N 208737 Rev. C
www.bannerengineering.com - Tel: + 1 888 373 6767
5
K50 Pro Touch Button with IO-Link
4-Pin Threaded M12/Euro-Style Cordsets—Double Ended, Oil Resistant
Model
Length
Style
Dimensions
Pinout
MQDEC-401SS-PUR
MQDEC-403SS-PUR
MQDEC-406SS-PUR
MQDEC-415SS-PUR
0.3 m (1 ft)
1 m (3.28 ft)
2 m (6.56 ft)
5 m (16.40 ft)
Female
2
3
40 Typ.
[1.58"]
1
4
M12 x 1
Male
ø 14.5 [0.57"]
Male Straight/
Female Straight
44 Typ.
[1.73"]
1
4
2
3
MQDEC-430SS-PUR
10 m (32.81 ft)
M12 x 1
ø 14.5 [0.57"]
1 = Brown
2 = White
3 = Blue
4 = Black
4-Pin Threaded M12/Euro-Style Cordsets—Double Ended, Washdown, Stainless Steel
Model
Length
Style
Dimensions
Pinout
MQDEC-WDSS-401SS
MQDEC-WDSS-403SS
MQDEC-WDSS-406SS
0.3 m (1 ft)
0.91 m (3 ft)
1.83 m (6 ft)
Female
2
3
1
4
40 Typ.
M12 x 1
Male
13.9
13.9
Male Straight/
Female Straight
1
4
43.5 Typ.
2
3
MQDEC-WDSS-412SS
3.66 m (12 ft)
1 = Brown
2 = White
3 = Blue
4 = Black
Brackets
SMB30A
45
SMB30FA
•
83.2
•
Right-angle bracket with curved
slot for versatile orientation
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm sensor
12-ga. stainless steel
Swivel bracket with tilt and pan
movement for precise
adjustment
C
61
•
•
•
•
Mounting hole for 30 mm sensor
12-ga. 304 stainless steel
Easy sensor mounting to
extrude rail T-slot
B
•
•
68.9
36.3
B
A
A
69
•
Metric and inch size bolt
available
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 - 1.5 x 50
Hole size: B= ø 30.1
6
www.bannerengineering.com - Tel: + 1 888 373 6767
P/N 208737 Rev. C
K50 Pro Touch Button with IO-Link
SMB30FVK
SMB30MM
•
•
•
V-clamp, flat bracket and
fasteners for mounting to pipe or
extensions
Clamp accommodates 28 mm
dia. tubing or 1 in. square
extrusions
•
12-ga. stainless steel bracket
with curved mounting slots for
versatile orientation
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm sensor
57
70
46
A
118
C
•
•
57
B
30 mm hole for mounting
sensors
A
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
Hole size: A= ø 31
SMB30RAVK
SMB30SC
67
A
•
•
•
V-clamp, right-angle bracket
and fasteners for mounting
sensors to pipe or extrusion
Clamp accommodates 28 mm
dia. tubing or 1 in. square
extrusions
30 mm hole for mounting
sensors
•
•
•
Swivel bracket with 30 mm
mounting hole for sensor
Black reinforced thermoplastic
polyester
Stainless steel mounting and
swivel locking hardware
included
B
46
58
90
57
29
A
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
Hole size: A = ø 30.5
45
SMBAMS30P
SMBAMS30RA
45
•
•
Flat SMBAMS series bracket
30 mm hole for mounting
sensors
•
•
•
•
Right-angle SMBAMS series
C
C
bracket
30 mm hole for mounting
sensors
Articulation slots for 90°+
rotation
53
A
A
B
93
•
•
Articulation slots for 90°+
rotation
12-ga. 300 series stainless steel
B
48
12-ga. (2.6 mm) cold-rolled steel
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Ø A
TC-K50-CL
•
Touch cover
B
Diameter: A = 67 mm
Height: B = 42.5 mm
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not
cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO
BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES
RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT,
STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously
manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the
product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will
void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at
any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to:
www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.
P/N 208737 Rev. C
www.bannerengineering.com - Tel: + 1 888 373 6767
7
K50 Pro Touch Button with IO-Link
FCC Part 15 and CAN ICES-3 (B)/NMB-3(B)
This device complies with part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). Operation is subject to the following two conditions:
1.
2.
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the manufacturer.
©
Banner Engineering Corp. All rights reserved
相关型号:
©2020 ICPDF网 联系我们和版权申明