K70RPT2GRYC4Q [BANNER]
EZ-LIGHT® Touch K70 Specialty Pick-to-Light;
| 型号： | K70RPT2GRYC4Q |
| 厂家： | 
Banner Engineering |
| 描述： | EZ-LIGHT® Touch K70 Specialty Pick-to-Light |
| 文件： | 总5页 (文件大小：332K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
®
EZ-LIGHT Touch K70 Specialty Pick-to-
Light
Datasheet
Compact, Single-Point Devices for Error-Proofing of Bin-Picking Operations
•
•
Excellent immunity to false triggering by water spray, detergents, oils, and other
foreign materials
Rugged, cost-effective and easy-to-install solutions for error-proofing and parts-
verification applications
•
•
Compact devices are completely self contained—No controller needed
Illuminated dome provides an easy-to-see green job light: some models also light
red for alternate operation
•
•
•
Easy actuation—no force required
12 V to 30 V dc operation
Can be actuated with bare hands or in gloves
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Models
Indicators
1
2
Model
Function
Output
Connection
Job
Mis-Pick
Sense
K70APT2GRYC3Q
•
•
•
Job light always on with job input until
touched
Touch activates output and overrides job
light with sense light
Touch with inactive job input activates mis-
pick light and activates output
PNP, N.O.
PNP, N.C.
PNP, N.O.
Green
Red
Yellow
K70RPT2GRYC3Q
K70APT2GRYC4Q
Integral 5-pin
M12/Euro-style
male quick
disconnect
(QD)
•
•
Job light always on with job input until
touched
Touch activates output and overrides job
light with sense light until job input is
removed
Touch with inactive job input activates mis-
pick light for 5 seconds after touched and
activates output
Green
Red
Yellow
K70RPT2GRYC4Q
PNP, N.C.
•
Indicator and Output Behavior
NOTE: "C3" and "C4" models as referenced in the table pertain to a part of the product model number, immediately preceding
the designation.
Output Signal
Status
Sensor Conditions
Job input active Hand/pick absent
C3 Models
On Green
C4 Models
On Green
Off
1
Integral 5-pin M12/Euro-style quick disconnect models are listed.
•
•
To order the 2 m (6.5 ft) PVC cable model, omit the suffix "Q" in the model number. For example, K70APT2GRYC3.
To order the 150 mm (6 in) Euro-style PUR cable quick disconnect model, replace the suffix "Q" with "QPMA" in the model number. For
example, K70APT2GRYC3QPMA.
•
To order the 150 mm (6 in) PVC cable model with a 5-pin M12/Euro-style PVC connector, replace the suffix "Q" with "QP" in the model
number. For example, K70APT2GRYC3QP.
•
Models with a quick disconnect require a mating cordset.
2
PNP models only are listed. For other output types, contact Banner Engineering.
Original Document
189842 Rev. C
22 July 2016
189842
®
EZ-LIGHT Touch K70 Specialty Pick-to-Light
Output Signal
Status
Sensor Conditions
Hand/pick present
C3 Models
On Yellow
C4 Models
On Yellow until job input is removed
Off
On
Off
Hand/pick absent
Hand/pick present
Off
No job input
On Red
On Red for 5 seconds after hand/pick is removed
On
Specifications
Supply Voltage
Mounting
12 V to 30 V dc
M30 × 1.5 threaded base; maximum torque 4.5 N·m (40 in·lbf)
Supply Current
Indicators
< 220 mA maximum current at 12 V dc (exclusive of load)
< 110 mA maximum current at 30 V dc (exclusive of load)
Job pick indicator: Green
Mis-pick indicator: Red
Sense indicator: Yellow
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Indicator Lumens
Output Rating
Color
Green
Red
Typical Wavelength
Typical Intensity (lm)
Maximum load: 150 mA
ON-State saturation voltage: < 2 V dc at 10 mA ; < 2.5 V dc at 150
mA
525 nm
625 nm
590 nm
45
26
13
OFF-State leakage current: < 10 µA at 30 V dc
Output Response Time
Yellow
50 ms ON; 500 ms leading edge OFF
Power-Up Delay
300 ms
Operating Conditions
Required Overcurrent Protection
−40 °C to +50 °C (−40 °F to +122 °F)
90% at +50 °C maximum relative humidity (non-condensing)
WARNING: Electrical connections must be
made by qualified personnel in accordance
with local and national electrical codes and
regulations.
Storage
−40 °C to +70 °C (−40 °F to +158 °F)
Environmental Rating
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via
Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to http://
www.bannerengineering.com.
IEC IP65
Construction
Housing and dome: Polycarbonate
Mounting nut: PBT
Connections
Integral 5-pin M12/Euro-style male quick disconnect (QD); 2 m (6.5 ft)
unterminated PVC-jacketed cable; 150 mm (6 in) PVC cable with a 5-
pin M12/Euro-style male quick disconnect (QD); or 150 mm (6 in) PUR
cable with a 5-pin M12/Euro-style male quick disconnect (QD)
Supply Wiring
(AWG)
Required Overcurrent Protection
(Amps)
Vibration and Mechanical Shock
20
22
24
26
28
30
5.0
3.0
2.0
1.0
0.8
0.5
Vibration 10 Hz to 55 Hz 1.0 mm p-p amplitude per IEC 60068-2-6
Shock 30G 11 ms duration, half sine wave per IEC 60068-2-27
Certifications
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 189842 Rev. C
®
EZ-LIGHT Touch K70 Specialty Pick-to-Light
Dimensions
R31.8
[1.25]
70.0
[2.76]
63.5
[2.50]
49.7
[1.96]
20.9
[.82]
24.9
[.98]
M30 x 1.5-6g
M12 x 1-6g
8.0
[.32]
All measurements are listed in millimeters [inches], unless noted otherwise.
Wiring Diagram
NPN (Sinking) Output Models
Wiring Key
PNP (Sourcing) Output Models
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Gray
1
1
+
+
12-30V dc
–
12-30V dc
–
3
3
4
4
Load
Load
2
2
5
Job Light Enable,
Input High >7V
Job Light Enable,
Input Low <1.0V
5
Not Used
Not Used
NOTE: Cabled wiring diagrams are shown.Quick disconnect (QD) wiring diagrams are functionally identical.
Accessories
Cordsets
5-Pin Threaded M12/Euro-Style Cordsets—Single Ended
Model
Length
Style
Dimensions
Pinout (Female)
MQDC1-501.5
MQDC1-506
MQDC1-515
0.50 m (1.5 ft)
1.83 m (6 ft)
4.57 m (15 ft)
2
1
4
44 Typ.
3
5
Straight
1 = Brown
2 = White
3 = Blue
M12 x 1
ø 14.5
MQDC1-530
9.14 m (30 ft)
4 = Black
5 = Gray
P/N 189842 Rev. C
www.bannerengineering.com - Tel: +1-763-544-3164
3
®
EZ-LIGHT Touch K70 Specialty Pick-to-Light
5-Pin Threaded M12/Euro-Style Cordsets—Single Ended
Model
Length
Style
Dimensions
Pinout (Female)
MQDC1-506RA
MQDC1-515RA
1.83 m (6 ft)
4.57 m (15 ft)
32 Typ.
[1.26"]
30 Typ.
[1.18"]
Right-Angle
MQDC1-530RA
9.14 m (30 ft)
M12 x 1
ø 14.5 [0.57"]
Brackets
SMB30A
45
60
B
85
•
Right-angle bracket with
curved slot for versatile
orientation
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
45
SSA-MBK-EEC1
C
B
•
•
Single 30 mm hole
8 gauge steel, black finish
(powder coat)
61
•
•
•
80
A
•
Front surface for customer
applied labels
69
A
12-ga. stainless steel
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
Hole size: A = ø 7 , B = ø 30
SMB30FVK
SMB30MM
•
•
•
V-clamp, flat bracket and
fasteners for mounting to
pipe or extensions
Clamp accommodates 28
mm dia. tubing or 1 in.
square extrusions
•
12-ga. stainless steel bracket
with curved mounting slots
for versatile orientation
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
57
70
46
A
118
C
•
•
57
B
A
30 mm hole for mounting
sensors
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
Hole size: A= ø 31
45
SMB30RAVK
SMBAMS30P
A
•
•
•
V-clamp, right-angle bracket
and fasteners for mounting
sensors to pipe or extrusion
Clamp accommodates 28
mm dia. tubing or 1 in.
square extrusions
30 mm hole for mounting
sensors
•
•
Flat SMBAMS series bracket
30 mm hole for mounting
sensors
C
46
A
93
•
•
Articulation slots for 90°+
rotation
12-ga. 300 series stainless
steel
B
90
57
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Hole size: A = ø 30.5
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 189842 Rev. C
®
EZ-LIGHT Touch K70 Specialty Pick-to-Light
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE
OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp.
Copyright Notice
Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not
intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product
warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any
©
time. For the most recent version of any documentation, refer to: www.bannerengineering.com.
Banner Engineering Corp. All rights reserved.
www.bannerengineering.com - Tel: +1-763-544-3164
相关型号：
©2020 ICPDF网 联系我们和版权申明