K30ALBTRGHQ [BANNER]
EZ-LIGHT® Touch K30 Series Illuminated Buttons;型号: | K30ALBTRGHQ |
厂家: | Banner Engineering |
描述: | EZ-LIGHT® Touch K30 Series Illuminated Buttons |
文件: | 总4页 (文件大小:337K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
®
EZ-LIGHT Touch K30 Series Illuminated
Buttons
Datasheet
Lighted Touch Button with Bipolar Outputs
•
•
•
Rugged, cost-effective, and easy-to-install touch button with multicolor light
Momentary versions remain activated as long as touch is present
Latching versions start up not activated and toggle between activated and not
activated on successive touches
•
•
Waterproof IP69K construction for washdown environments
Ergonomically designed to eliminate hand, wrist, and arm stresses associated with
repeated switch operation; require no physical force to operate
•
•
Can be actuated with bare hands or in gloves
12 V dc to 30 V dc operation
Models
Light (not
activated)
Light
(activated)
1
Connection
Model
Function
Output
K30ALBTXGHQ
K30RLBTXGHQ
K30ABTXGHQ
K30RBTXGHQ
K30ALBTGGHQ
K30RLBTGGHQ
K30ABTGGHQ
K30RBTGGHQ
K30ALBTRGHQ
K30RLBTRGHQ
K30ABTRGHQ
K30RBTRGHQ
Bipolar, N.O.
Bipolar, N.C.
Bipolar, N.O.
Bipolar, N.C.
Bipolar, N.O.
Bipolar, N.C.
Bipolar, N.O.
Bipolar, N.C.
Bipolar, N.O.
Bipolar, N.C.
Bipolar, N.O.
Bipolar, N.C.
Latching
-
Green
Green
Green
Momentary
Latching
Integral 5-pin M12/Euro-
style male quick disconnect
Green
Momentary
Latching
Red
Momentary
Wiring Diagrams
Color Key
1 = Brown
1
3
2 = White
3 = Blue
4 = Black
5 = Gray
+
12-30V dc
–
2
4
5
Load
Load
Not Used
1
Integral 5-pin M12/Euro-style quick disconnect models are listed.
•
To order the 150 mm (6 in) PVC cable model with a 5-pin M12/Euro-style quick disconnect, replace the suffix "Q" with "QP" in the model
number. For example, K30ALBTXGHQP.
•
•
To order the 2 m (6.5 ft) PVC cable model, omit the suffix "Q" in the model number. For example, K30ALBTXGH.
Models with a quick disconnect require a mating cordset.
Original Document
170455 Rev. E
21 November 2016
170455
®
EZ-LIGHT Touch K30 Series Illuminated Buttons
NOTE: Cabled wiring diagrams are shown. Quick disconnect (QD) wiring diagrams are functionally identical.
Specifications
Supply Voltage
Output Response Time
12 V dc to 30 V dc
150 milliseconds ON and OFF
Supply Current
Power-Up Delay
55 mA max current (exclusive of load)
300 milliseconds
Latching models start up in a 'not activated' state
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Connections
5-pin integral M12/Euro-style QD, 2 m (6.5 ft) PVC integral cable, or 5-
pin 150 mm (6 in) M12/Euro-style PVC cable QD
Output Rating
Maximum Load: 150 mA
Construction
ON-state saturation voltage: < 2 V dc at 10 mA; < 2.5 V dc at 150
mA
Housing: polycarbonate
Translucent dome: polycarbonate
Mounting nut: PBT
OFF-state leakage current <10 µA at 30 V dc
Mounting
Required Overcurrent Protection
M22 × 1.5 Threaded base, max torque 2.25 Nm (20 in-lbf)
WARNING: Electrical connections must be
made by qualified personnel in accordance
with local and national electrical codes and
regulations.
Environmental Rating
IEC IP67, IP69K per DIN 40050-9.
Cabled models also meet IP69K if the cable and cable entrance are
protected from high-pressure spray.
Enclosure Type 4X, 13
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via
Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.
Operating Conditions
–40 °C to +50 °C (–40 °F to +122 °F)
90% at 50 °C maximum relative humidity (non-condensing)
Storage
–40 °C to +70 °C (–40 °F to +158 °F)
Supply Wiring (AWG)
Required Overcurrent Protection (Amps)
Vibration and Mechanical Shock
All models meet Mil. Std. 202F requirements method 201A (vibration:
10 Hz to 60 Hz max., double amplitude 0.06 in. maximum
acceleration 10G). Also meets IEC 947-5-2; 30G 11 ms duration, half
sine wave.
20
22
24
26
28
30
5.0
3.0
2.0
1.0
0.8
0.5
Certifications
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 170455 Rev. E
®
EZ-LIGHT Touch K30 Series Illuminated Buttons
Accessories
Cordsets
5-Pin Threaded M12/Euro-Style Cordsets—Single Ended
Model
Length
Style
Dimensions
Pinout (Female)
MQDC1-501.5
MQDC1-506
MQDC1-515
0.50 m (1.5 ft)
1.83 m (6 ft)
4.57 m (15 ft)
44 Typ.
Straight
M12 x 1
2
MQDC1-530
9.14 m (30 ft)
ø 14.5
1
4
3
MQDC1-506RA
MQDC1-515RA
1.83 m (6 ft)
4.57 m (15 ft)
5
32 Typ.
[1.26"]
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Gray
30 Typ.
[1.18"]
Right-Angle
MQDC1-530RA
9.14 m (30 ft)
M12 x 1
ø 14.5 [0.57"]
5-Pin Threaded M12/Euro-Style Cordsets—Washdown Stainless Steel
Model
Length
Style
Dimensions
Pinout (Female)
MQDC-WDSS-0506
MQDC-WDSS-0515
1.83 m (6 ft)
4.57 m (15 ft)
2
1
4
3
Ø15.5 mm
5
Straight
1 = Brown
2 = White
3 = Blue
Ø4.8 mm
MQDC-WDSS-0530
9.14 m (30 ft)
43.5 mm
4 = Black
5 = Gray
5-Pin Threaded M12/Euro-Style Cordsets—Washdown, with Shield
Model
Length
Style
Dimensions
Pinout (Female)
MQDCWD-506
1.83 m (6 ft)
2
1
4
42 Typ.
[1.65"]
3
5
ø 15.0
[0.57"]
Straight
1 = Brown
2 = White
3 = Blue
MQDCWD-530
9.14 m (30 ft)
M12 x 1
4 = Black
5 = Gray
P/N 170455 Rev. E
www.bannerengineering.com - Tel: +1-763-544-3164
3
®
EZ-LIGHT Touch K30 Series Illuminated Buttons
Brackets
SMB22A
SMB22FVK
32
46
118
•
Right-angle bracket with curved slot
for versatile orientation
12-ga. stainless steel
Mounting hole for 22 mm sensor
•
V-clamp, flat bracket and fasteners
for mounting to pipe or extensions
C
ø22.5
41
•
•
•
Clamp accommodates 28 mm
diameter tubing or 1 in. square
extrusions
A
B
34
A
•
22 mm hole for mounting sensor
46
Hole size: A = ø 22.5
Hole center spacing: A to B = 26.0
Hole size: A = ø 4.6, B = 4.6 x 16.9, C = 22.2
45
SMB22RAVK
SMBAMS22P
A
•
•
•
V-clamp, right-angle bracket and
fasteners for mounting to pipe or
extensions
Clamp accommodates 28 mm
diameter tubing or 1 in. square
extrusions
•
Flat SMBAMS series bracket with 22
C
mm hole for mounting sensors
Articulation slots for 90+° rotation
12-ga. (2.6 mm) cold-rolled steel
46
•
•
A
93
B
90
57
22 mm hole for mounting sensor
Hole size: A = ø 22.5
Hole center spacing: A = 26.0, A to B = 13.0
Hole size: A = 26.8 x 7.0, B = ø 6.5, C = ø 22.5
Ø A
SMBAMS22RA
45
TC-K30-CL
•
Right-angle SMBAMS series bracket
with 22 mm hole for mounting
sensors
•
Touch cover
C
53
B
A
•
•
Articulation slots for 90+° rotation
12-ga. (2.6 mm) cold-rolled steel
B
48
Diameter: A = 40.7
Height: B = 31
Hole center spacing: A = 26.0, A to B = 13.0
Hole size: A = 26.8 x 7.0, B = ø 6.5, C = ø 22.5
All measurements are listed in millimeters, unless noted otherwise.
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE
OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection
applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval
by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product
specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most
recent version of any documentation, refer to: www.bannerengineering.com.
©
Banner Engineering Corp. All rights reserved
相关型号:
©2020 ICPDF网 联系我们和版权申明