ATM0177B3A-T [AZDISPLAYS]
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY;型号: | ATM0177B3A-T |
厂家: | AZ DISPLAYS |
描述: | SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY |
文件: | 总16页 (文件大小:333K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
AZ DISPLAYS
SPECIFICATIONS FOR
LIQUID CRYSTAL DISPLAY
CUSTOMER APPROVAL
※ PART NO. : ATM0177B3A (AZ DISPLAYS) VER1.0
COMPANY
APPROVAL
CHOP
CUSTOMER
COMMENTS
AZ DISPLAYS ENGINEERING APPROVAL
DESIGNED BY
CHECKED BY
APPROVED BY
CXH
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
REVISION RECORD
REVISION
REVISION DATE
PAGE
CONTENTS
VER1.0
2014-04-09
FIRST ISSUED
1
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
※ CONTENTS
1. GENERAL SPECIFICATIONS
2. PIN ASSIGNMENT
3. OPERATING SPECIFICATIONS
4. OPTICAL SPECIFICATIONS
5. RELIABILITY TEST
6. PRECAUTION FOR USING LCM
7. MECHANICAL DRAWING
8. PACKAGE DRAWING
9. INSPECTION SPECIFICATION
2
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
1. GENERAL SPECIFICATIONS
Item
Specification
Remark
1. LCD size
1.77 inch(Diagonal)
a-Si TFT active matrix
128x(RGB)x160
2. Driver element
3. Resolution
4. Display mode
5. Dot Pitch (W*H)
6. Pixel pitch(W*H)
7. Active Area(W*H)
8. Module size (W*H)
9. Surface treatment
10. Color arrangement
11. Color
Normally white , Transmissive
0.073mm(W) x 0.219mm(H)
0.219mm(W) x 0.219mm(H)
28.032mm(W) x 35.04mm(H)
34.70mm(W) x 46.7mm(H) x 2.5mm(D)
Anti-glare
Note 1
RGB-stripe
65K
12. Contrller
ILI9163V
13. Interface
4-wire SPI
14. Weight
5.4g(Typ.)
15. RoHS
RoHS compliant
Note 1: Please refer to mechanical drawing.
3
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
2. PIN ASSIGNMENT
Pin No.
Symbol
Function
Level
Note
1
2
K
A
Power for LED backlight(Anode)
Power for LED backlight(Cathode)
No connection
P
P
--
--
P
P
I/O
I
3
NC
4
NC
No connection
5
GND
VCC
SDA
SCK
A0
Power ground
6
Power supply
7
Serial data
8
Serial clock
9
Data/clock selection
Reset
I
10
11
REST
CS
I
Chip selection
I
I: input, O: output, P: Power
4
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
3. Operating Specification
3.1 ABSOLUTE MAXIMUM RATINGS
Values
Min.
Item
Symbol
Unit
Remark
Max.
4.6
70
Power Voltage
VCC
TOP
TST
-0.3
-20
-30
V
Operation Temperature
Storage Temperature
ºC
ºC
80
Each LED
Note 2
LED Reverse Voltage
LED Forward Current
VR
IF
-
1.2
25
V
mA
Each LED
Note 1: The absolute maximum rating values of this product are not allowed to be exceeded
at any times. Should a module be used with any of the absolute maximum ratings
exceeded, the characteristics of the module may not be recovered, or in an extreme
case, the module may be permanently destroyed.
Note 2: VR Conditions: Zener Diode 20mA
3.1.1 Typical Operation Conditions
Values
Item
Symbol
Unit
Remark
Min.
2.6
Typ.
2.8
--
Max.
3.3
Power Voltage
VCC
VIH
VIL
V
V
V
Input Logic High Voltage
Input Logic Low Voltage
0.8VCC
0
VCC
--
0.2VCC
3.1.2 Backlight driving conditions
Values
Typ.
3.2
Item
Symbol
Unit
Remark
Min.
2.9
Max.
3.3
60
Voltage for LED Backlight
Current for LED Backlight
LED life time
VL
IL
V
45
54
mA
Hr
--
30000
--
--
Note 1
Note 1: The “LED life time” is defined as the module brightness decrease to 50% original brightness at
Ta=25℃ and IL =54mA.
5
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
3.3 Timing Characteristics
6
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
7
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
4.0 OPTICAL SPECIFICATIONS
Values
Typ.
70
Item
Symbol
Condition
Unit
Remark
Min.
60
Max.
--
θL
θR
Φ=180o(9 O'CLOCK)
Φ=0o(3 O'CLOCK)
Φ=90o(12 O'CLOCK)
Φ=270o(6 O'CLOCK)
Note 1
60
70
--
Viewing Angle
degree
θT
20
30
--
(CR≥10)
θB
35
45
--
TON
TOFF
CR
WX
--
10
20
30
--
msec
msec
--
Note 3
Note 3
Note 4
Note 2
Note 5
Note 6
Note 6
Note 7
Response Time
Contrast Ratio
--
15
400
0.26
500
0.31
Normal
Θ=Φ=0o
0.36
--
Color Chromaticity
WY
0.28
0.33
0.38
--
Luminance
L
450
75
--
--
--
cd/m2
%
Luminance Uniformity
YU
80
Test Conditions:
1. Vf=3.2V (Backlight current), the ambient temperature is 25℃.
2. The test systems refer to Note 2.
Note 1: Definition of viewing angle range
Figure 4.1 Definition of viewing angle.
8
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
Note 2: Definition of optical measurement system.
The optical characteristics should be measured in dark room. After 30 minutes operation, the optical properties are
measured at the center point of the LCD screen. (Response time is measured by Photo detector TOPCON
Figure 4.2 Optical measurement system setup
Note 3: Definition of Response time
The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise
time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the
time between photo detector output intensity changed from 10% to 90%.
Figure 4.3 Definition of response.
9
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
Note 4: Definition of contrast ratio
Note 5: Definition of color chromaticity (CIE1931)
Color coordinates measured at center point of LCD.
Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel.
Note 7: Definition of Luminance Uniformity
Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each
measuring area.
Figure 4.3 Definition of measuring points.
Bmax: The measured maximum luminance of all measurement position.
Bmin: The measured minimum luminance of all measurement position.
10
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
5. RELIABILITY TEST
Item
Test Condition Item
Ta= 70 ºC 240hrs
Remark
Note 1
Note 4
High temperature
storage
Note 1
Note 4
Low temperature
storage
Ta=-20 ºC 240hrs
Ts= 60 ºC 240hrs
Note 2
Note 4
High temperature
operation
Note 1
Note 4
Low temperature
operation
Ts=-10 ºC 240hrs
High temperature/High
humidity operation
Note 4
90% RH 40ºC 120hrs
-1℃/30 min ~ +6℃/30 min for a total 10
cycles, Start with cold temperature and end
with high temperature.
Thermal Shock
Note 4
Height:100 cm
1 corner, 3 edges, 6 surfaces
Package drop test
Note 1: Ta is the ambient temperature of samples.
Note 2: Ts is the temperature of panel’s surface.
Note 3: In the standard condition, there shall be no practical problem that may affect the
display function. After the reliability test, the product only guarantees operation,
but don’t guarantee all of the cosmetic specification.
Note 4: Before cosmetic and function test, the product must have enough recovery time, at least 2 hours
at room temperature.
11
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
6. PRECAUTION FOR USING LCM
1. When design the product with this LCD Module, make sure the viewing angle matches to its purpose of usage.
2. As LCD panel is made of glass substrate, Dropping the LCD module or banging it against hard objects may cause
cracking or fragmentation. Especially at corners and edges.
3. Although the polarizer of this LCD Module has the anti-glare coating, always be careful not to scratch its surface.
Use of a plastic cover is recommended to protect the surface of polarizer.
4. If the LCD module is stored at below specified temperature, the LC material may freeze and be deteriorated. If it is
stored at above specified temperature, the molecular orientation of the LC material may change to Liquid state and it
may not revert to its original state. Excessive temperature and humidity could cause polarizer peel off or bubble.
Therefore, the LCD module should always be stored within specified temperature range.
5. Saliva or water droplets must be wiped off immediately as those may leave stains or cause color changes if
remained for a long time. Water vapor will cause corrosion of ITO electrodes.
6. If the surface of LCD panel needs to be cleaned, wipe it swiftly with cotton or other soft cloth. If it is not still clean
enough, blow a breath on the surface and wipe again.
7. The module should be driven according to the specified ratings to avoid malfunction and permanent damage.
Applying DC voltage cause a rapid deterioration of LC material. Make sure to apply alternating waveform by
continuous application of the M signal. Especially the power ON/OFF sequence should be kept to avoid latch-up of
driver LSIs and DC charge up to LCD panel.
8. Mechanical Considerations
a) LCM are assembled and adjusted with a high degree of precision. Avoid excessive shocks and do not make
any alterations or modifications. The following should be noted.
b) Do not tamper in any way with the tabs on the metal frame.
c) Do not modify the PCB by drilling extra holes, changing its outline, moving its components or modifying its
pattern.
9. Static Electricity
a) Operator
Wear the electrostatics shielded clothes because human body may be statically charged if not ware shielded clothes.
Never touch any of the conductive parts such as the LSI pads; the copper leads on the PCB and the interface terminals
with any parts of the human body.
b) Equipment
There is a possibility that the static electricity is charged to the equipment, which has a function of peeling or friction
action (ex: conveyer, soldering iron, working table). Earth the equipment through proper resistance (electrostatic earth:
1x108 ohm).
Only properly grounded soldering irons should be used.
If an electric screwdriver is used, it should be well grounded and shielded from commutator sparks.
The normal static prevention measures should be observed for work clothes and working benches; for the latter
conductive (rubber) mat is recommended.
c) Floor
Floor is the important part to drain static electricity, which is generated by operators or equipment.
There is a possibility that charged static electricity is not properly drained in case of insulating floor. Set the electrostatic
earth (electrostatic earth: 1x108 ohm).
d) Humidity
Proper humidity helps in reducing the chance of generating electrostatic charges. Humidity should be kept over 50%RH.
e) Transportation/storage
The storage materials also need to be anti-static treated because there is a possibility that the human body or storage
materials such as containers may be statically charged by friction or peeling.
The modules should be kept in antistatic bags or other containers resistant to static for storage.
f) Soldering
Soldering anything to this TFT display would void the warranty.
g) Others
The laminator (protective film) is attached on the surface of LCD panel to prevent it from scratches or stains. It should be
peeled off slowly using static eliminator.
Static eliminator should also be installed to the workbench to prevent LCD module from static charge.
10. Operation
a) Driving voltage should be kept within specified range; excess voltage shortens display life.
b) Response time increases with decrease in temperature.
c) Display may turn black or dark blue at temperatures above its operational range; this is (however not pressing
on the viewing area) may cause the segments to appear “fractured”.
d) Mechanical disturbance during operation (such as pressing on the viewing area) may cause the segments to
appear “fractured”.
12
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
11. If any fluid leaks out of a damaged glass cell, wash off any human part that comes into contact with soap and water.
The toxicity is extremely low but caution should be exercised at all the time.
12. Disassembling the LCD module can cause permanent damage and it should be strictly avoided.
13. LCD retains the display pattern when it is applied for long time (Image retention). To prevent image retention, do not
apply the fixed pattern for a long time. Image retention is not a deterioration of LCD. It will be removed after display
pattern is changed.
14. Do not use any materials, which emit gas from epoxy resin (hardener for amine) and silicone adhesive agent
(dealcohol or deoxym) to prevent discoloration of polarizer due to gas.
15. Avoid the exposure of the module to the direct sunlight or strong ultraviolet light for a long time.
13
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
7. MECHANICAL DRAWING
e a R r
t n o F r
14
AZ DISPLAYS
ATM0177B3A(AZ DISPLAYS)TFT MODULE VER1.0
8. PACKAGE DRAWING
T.B.D.
9. INSPECTION SPECIFICATION
T.B.D.
15
AZ DISPLAYS
相关型号:
©2020 ICPDF网 联系我们和版权申明