HLMP-EG3A-110DV [AVAGO]
Single Color LED, Red, Untinted, T-1 3/4, 5mm, ROHS COMPLIANT, PLASTIC PACKAGE-2;
| 型号： | HLMP-EG3A-110DV |
| 厂家： | 
AVAGO TECHNOLOGIES LIMITED |
| 描述： | Single Color LED, Red, Untinted, T-1 3/4, 5mm, ROHS COMPLIANT, PLASTIC PACKAGE-2 |
| 文件： | 总11页 (文件大小：194K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HLMP-Ex1A/1B-xxxDV (15° minimum),
HLMP-Ex3A/3B-xxxDV (30° minimum)
5mm Extra High Brightness AlInGaP LED lamps
Data Sheet
Description
Features
These 5mm Extra High Brightness AlInGaP LEDs provide • Viewing Angle: 15° minimum
superior light output for excellent readability in sunlight
and are extremely reliable. AlInGaP LED technology
provides extremely stable light output over long periods
of time. These Extra High Brightness lamps utilize
the aluminum indium gallium phosphide (AlInGaP)
technology.
30° minimum
• High luminous Intensity
• Color
– 590nm Amber
– 626nm Red
• Package options:
These LED lamps are untinted. T-1¾ packages incorpo-
rating second generation optics producing well defined
spatial radiation patterns at specific viewing cone angles.
– With or without standoff
• Superior resistance to moisture
• Untinted for 15° and 30° lamps
These lamps are made with an advanced optical grade
epoxy offering superior high temperature and high
moisture resistance performance in outdoor signal and
sign application. The maximum LED junction tempera-
ture limit of +130°C enables high temperature operation
in bright sunlight conditions. The epoxy contain both
uv-a and uv-b inhibitor to reduce the effects of long term
exposure to direct sunlight.
Applications
• Traffic management:
– Traffic signals
– Pedestrian signals
– Work zone warning lights
– Variable message signs
Benefits
• Solar Power signs
• Superior performance for outdoor environment
• Suitable for auto-insertion onto PC board
• Commercial outdoor advertising
– Signs
– Marquees
Package Dimension
B: Standoff
A: Non-standoff
5.00 0.20
(0.197 0.00ꢀ)
5.00 0.20
(0.197 0.00ꢀ)
1.14 0.20
(0.045 0.00ꢀ)
ꢀ.71 0.20
(0.343 0.00ꢀ)
ꢀ.71 0.20
(0.343 0.00ꢀ)
d
1.14 0.20
(0.045 0.00ꢀ)
2.35 (0.093)
MAX.
0.70 (0.02ꢀ)
MAX.
1.50 0.15
(0.059 0.006)
31.60
MIN.
31.60
MIN.
(1.244)
(1.244)
0.70 (0.02ꢀ)
MAX.
CATHODE
LEAD
CATHODE
LEAD
0.50 0.10
(0.020 0.004)
0.50 0.10
(0.020 0.004)
SQ. TYP.
SQ. TYP.
1.00
MIN.
1.00
(0.039)
MIN.
(0.039)
5.ꢀ0 0.20
(0.22ꢀ 0.00ꢀ)
5.ꢀ0 0.20
(0.22ꢀ 0.00ꢀ)
CATHODE
FLAT
CATHODE
FLAT
2.54 0.3ꢀ
(0.100 0.015)
2.54 0.3ꢀ
(0.100 0.015)
Viewing Angle
d
HLMP-Ex1B
12.39 0.25
(0.476 0.010)
HLMP-Ex3B
Notes:
11.96 0.25
(0.459 0.010)
1. All dimensions are in millimeters (inches)
2. Leads are mild steel with tin plating.
3. The epoxy meniscus is 1.21mm max
4. For Identification of polarity after the leads are
trimmed off, please refer to the illustration below:
CATHODE
ANODE
2
Device Selection Guide
Luminous Intensity Iv
Minimum viewing
Angle
[4]
2θ (Deg)
1/2
Color and Dominant
Wavelength (nm),
Typ
Lamps without Standoff Lamps with Standoff
[1,2,5]
(mcd)
at 20 mA
on leads
on leads
[3]
(Package drawing A)
(Package drawing B)
Min
Max
15°
Amber 590
HLMP-EL1A-Z1KDV
HLMP-EL1A-Z1LDV
HLMP-EG1A-Z10DV
HLMP-EL3A-WXKDV
HLMP-EL3A-WXLDV
HLMP-EG3A-WX0DV
HLMP-EL1B-Z1KDV
HLMP-EL1B-Z1LDV
HLMP-EG1B-Z10DV
HLMP-EL3B-WXKDV
HLMP-EL3B-WXLDV
HLMP-EG3B-WX0DV
12000
12000
12000
5500
5500
5500
21000
21000
21000
9300
Red 626
30°
Amber 590
9300
Red 626
9300
Notes:
1. The luminous intensity is measured on the mechanical axis of the lamp package.
2. The optical axis is closely aligned with the package mechanical axis.
3. Dominant wavelength, λ , is derived from the CIE Chromaticity Diagram and represents the color of the lamp.
d
4.
θ is the off-axis angle where the luminous intensity is half the on-axis intensity.
½
5. Tolerance for each bin limit is 15ꢀ
Part Numbering System
HLMP-E x xx – x x x xx
Packaging Option
DV: Ammo Pack with minimum viewing angle of 15° or 30°
Color Bin Selection
0: Full Distribution
K: Color Bin 2 & 4
L: Color Bin 4 & 6
Maximum Intensity Bin
Refer to Selection Guide
Minimum Intensity Bin
Refer to Devise Selection Guide
Viewing Angle and Lead Standoffs
1A: 15° without lead standoff
1B: 15° with lead standoff
3A: 30° without lead standoff
3B: 30° with lead standoff
Color
G: Red 626
L: Amber 590
Note: Please refer to AB 5337 for complete information on part numbering system.
3
Absolute Maximum Ratings
T = 25°C
J
Parameter
Red/ Amber
Unit
mA
mA
mA
mW
V
DC Forward Current [2]
Peak Forward Current
Average Forward Current
Power Dissipation
50
100 [1]
30
120
Reverse Voltage
5
Operating Temperature Range
Storage Temperature Range
-40 to +100
-40 to +100
°C
°C
Notes:
1. Duty Factor 30ꢀ, frequency 1KHz.
2. Derate linearly as shown in Figure 4
Electrical / Optical Characteristics
T = 25°C
J
Parameter
Symbol
Min
Typ.
Max
Units
Test Conditions
Forward Voltage
Red / Amber
VF
VR
λd
1.8
5
2.1
2.4
V
IF = 20 mA
IR = 100 μA
IF = 20 mA
Reverse Voltage
V
Dominant Wavelength[1]
nm
Amber
Red
587.0
618.0
590.0
626.0
594.5
630.0
Peak Wavelength
Amber
Red
λPEAK
nm
nm
Peak of Wavelength of Spectral
Distribution at IF = 20 mA
594
634
Spectral Halfwidth
Amber
Red
Δλ1/2
IF = 20 mA
13
14
Thermal resistance
RΦJ-PIN
240
°C/W
lm/W
LED junction to anode lead
Luminous Efficacy [2]
Amber
Red
ηv
Emitted Luminous Flux/Emitted
Radiant Flux
500
200
Luminous Flux
Amber
Red
Φv
ηe
mlm
IF = 20 mA
2000
1900
Luminous Efficiency [3]
Amber
Red
lm/W
nm/°C
Emitted Luminous Flux/Electrical
Power
50
55
Thermal coefficient of λd
IF = 20 mA ; +25°C ≤ TJ ≤ +100°C
Amber
Red
0.08
0.05
Notes:
1. The dominant wavelength, λ is derived from the CIE Chromaticity Diagram referenced to Illuminant E. Tolerance for each color of dominant
d
wavelength is +/- 0.5nm.
2. The radiant intensity, Ie in watts per steradian, maybe found from the equation I = I / η where Iv is the luminous intensity in candela and η is
e
v
V
V
the luminous efficacy in lumens/ watt.
3.
η Φ / I x V where Φ is the emitted luminous flux, I is electrical forward current and V is the forward voltage.
e = v F F v F F
4
1.0
0.ꢀ
0.6
0.4
0.2
0.0
100
ꢀ0
60
40
20
0
Amber
Red
500
550
600
650
700
0
1
2
3
WAVELENGTH - nm
FORWARD VOLTAGE-V
Figure 1. Relative Intensity vs Peak Wavelength
Figure 2. Forward Current vs Forward Voltage
60
50
40
30
20
10
0
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
20
40
60
ꢀ0
100
0
20
40
60
ꢀ0
100
DC FORWARD CURRENT - mA
TA - AMBIENT TEMPERATURE - C
Figure 3. Relative Luminous Intensity vs Forward Current
Figure 4. Maximum Forward Current vs Ambient Temperature
1.0
0.ꢀ
0.6
0.4
0.2
0.0
1.0
0.ꢀ
0.6
0.4
0.2
0.0
-90
-60
-30
0
30
60
90
-90
-60
-30
0
30
60
90
ANGULAR DISPLACEMENT - DEGREES
ANGULAR DISPLACEMENT-DEGREE
Figure 5. Radiation Pattern for 15° (minimum 15°)
Figure 6. Radiation Pattern for 30° (minimum 30°)
5
0.20
0.15
0.10
0.05
0.00
-0.05
-0.10
-0.15
-0.20
10
1
Red
Amber
Red
Amber
0.1
-40 -20
0
20
40 60
ꢀ0 100 120 140
-40 -20
0
20 40
60 ꢀ0 100 120 140
TJ - JUNCTION TEMPERATURE - °C
TJ - JUNCTION TEMPERATURE - °C
Figure 7. Relative Light Output vs Junction Temperature
Figure ꢀ. Relative Forward Voltage vs Junction Temperature
Intensity Bin Limit Table (1.3:1 Iv bin ratio)
Intensity (mcd) at 20mA
Red Color Range
Min Dom Max Dom X min
Y Min
X max
Y max
618.0
630.0
0.6872
0.6690
0.3126
0.3149
0.6890
0.7080
0.2943
0.2920
Bin
W
X
Min
Max
5500
7200
9300
12000
16000
7200
9300
12000
16000
21000
Tolerance for each bin limit is 0.5nm
Y
Z
1
Amber Color Range
Tolerance for each bin limit is 15ꢀ
Bin Min Dom Max Dom Xmin
Ymin
Xmax
Ymax
2
4
6
587.0
589.5
592.0
589.5
592.0
594.5
0.5570 0.4420 0.5670 0.4250
0.5530 0.4400 0.5720 0.4270
0.5720 0.4270 0.5820 0.4110
0.5670 0.4250 0.5870 0.4130
0.5870 0.4130 0.5950 0.3980
0.5820 0.4110 0.6000 0.3990
V Bin Table (V at 20mA)
F
Bin ID
VD
Min
1.8
2.0
2.2
Max
2.0
2.2
2.4
VA
Tolerance for each bin limit is 0.5nm
VB
Note:
Tolerance for each bin limit is 0.05V
All bin categories are established for classification of products. Products
may not be available in all bin categories. Please contact Avago
representative for further information.
6
Avago Color Bin on CIE 1931 Chromaticity Diagram
0.4ꢀ0
0.460
0.440
Amber
2
0.420
0.400
0.3ꢀ0
0.360
0.340
0.320
0.300
0.2ꢀ0
4
6
Red
0.500
0.550
0.600
0.650
0.700
0.750
0.ꢀ00
X
7
Precautions:
Lead Forming:
• The leads of an LED lamp may be preformed or cut to
Note:
1. PCB with different size and design (component density) will have
different heat mass (heat capacity). This might cause a change in
temperature experienced by the board if same wave soldering
setting is used. So, it is recommended to re-calibrate the soldering
profile again before loading a new type of PCB.
2. Avago Technologies’ high brightness LED are using high efficiency
LED die with single wire bond as shown below. Customer is advised
to take extra precaution during wave soldering to ensure that the
maximum wave temperature does not exceed 260°C and the solder
contact time does not exceeding 5sec. Over-stressing the LED
during soldering process might cause premature failure to the LED
due to delamination.
length prior to insertion and soldering on PC board.
• For better control, it is recommended to use proper
tool to precisely form and cut the leads to applicable
length rather than doing it manually.
• If manual lead cutting is necessary, cut the leads after
the soldering process. The solder connection forms a
mechanical ground which prevents mechanical stress
due to lead cutting from traveling into LED package.
This is highly recommended for hand solder operation,
as the excess lead length also acts as small heat sink.
Avago Technologies LED Configuration
Soldering and Handling:
• Care must be taken during PCB assembly and soldering
process to prevent damage to the LED component.
• LED component may be effectively hand soldered
to PCB. However, it is only recommended under
unavoidable circumstances such as rework. The closest
manual soldering distance of the soldering heat source
(soldering iron’s tip) to the body is 1.59mm. Soldering
the LED using soldering iron tip closer than 1.59mm
might damage the LED.
Anode
Note: Electrical connection between bottom surface of LED die and
the lead frame is achieved through conductive paste.
1.59mm
• Any alignment fixture that is being applied during
wave soldering should be loosely fitted and should
not apply weight or force on LED. Non metal material
is recommended as it will absorb less heat during
wave soldering process.
• ESD precaution must be properly applied on the
soldering station and personnel to prevent ESD
damage to the LED component that is ESD sensitive.
Do refer to Avago application note AN 1142 for details.
The soldering iron used should have grounded tip to
ensure electrostatic charge is properly grounded.
Note: In order to further assist customer in designing jig accurately
that fit Avago Technologies’ product, 3D model of the product is
available upon request.
• At elevated temperature, LED is more susceptible to
mechanical stress. Therefore, PCB must allowed to cool
down to room temperature prior to handling, which
includes removal of alignment fixture or pallet.
• Recommended soldering condition:
Wave
Soldering
Manual Solder
Dipping
• If PCB board contains both through hole (TH) LED and
other surface mount components, it is recommended
that surface mount components be soldered on the
top side of the PCB. If surface mount need to be on the
bottom side, these components should be soldered
using reflow soldering prior to insertion the TH LED.
[1, 2]
Pre-heat temperature 105°C Max.
–
Preheat time
Peak temperature
Dwell time
Note:
60 sec Max
260°C Max.
5 sec Max.
–
260°C Max.
5 sec Max
• Recommended PC board plated through holes (PTH)
1. Above conditions refers to measurement with thermocouple
mounted at the bottom of PCB.
2. It is recommended to use only bottom preheaters in order to
reduce thermal stress experienced by LED.
size for LED component leads.
LED component
lead size
Plated through
hole diameter
Diagonal
• Wave soldering parameters must be set and
maintained according to the recommended
temperature and dwell time. Customer is advised
to perform daily check on the soldering profile to
ensure that it is always conforming to recommended
soldering conditions.
0.45 x 0.45 mm
0.636 mm
0.98 to 1.08 mm
(0.039 to 0.043 inch)
(0.018x 0.018 inch) (0.025 inch)
0.50 x 0.50 mm 0.707 mm
(0.020x 0.020 inch) (0.028 inch)
1.05 to 1.15 mm
(0.041 to 0.045 inch)
• Over-sizing the PTH can lead to twisted LED after
clinching. On the other hand under sizing the PTH can
cause difficulty inserting the TH LED.
8
Refer to application note AN5334 for more information about soldering and handling of high brightness TH LED lamps.
Example of Wave Soldering Temperature Profile for TH LED
260°C Max
Recommended solder:
Sn63 (Leaded solder alloy)
SAC305 (Lead free solder alloy)
Flux: Rosin flux
Solder bath temperature: 255°C 5°C
(maximum peak temperature = 260°C)
105°C Max
Dwell time: 3.0 sec - 5.0 sec
(maximum = 5 sec)
Note: Allow for board to be sufficiently
cooled to room temperature before
exerting mechanical force.
60 sec Max
TIME (sec)
Ammo Packs Drawing
6.35 1.30
12.70 1.00
0.250 0.051
0.500 0.039
CATHODE
20.5 1.00
0.ꢀ070 0.0394
9.125 0.625
0.3595 0.0245
1ꢀ.00 0.50
0.70ꢀ5 0.0195
4.00 0.20
TYP.
0.70 0.20
0.0275 0.0075
Ø
12.70 0.30
0.500 0.012
0.1575 0.0075
A
A
VIEW AA
Note: The ammo-packs drawing is applicable for packaging option –DD & -ZZ and regardless standoff or non-standoff
9
Packaging Box for Ammo Packs
Note: The dimension for ammo pack is applicable for the device with standoff and without standoff.
Packaging Label:
(i) Avago Mother Label: (Available on packaging box of ammo pack and shipping box)
STANDARD LABEL LS0002
(1P) Item: Part Number
RoHS Compliant
e3 max temp 260C
(Q) QTY: Quantity
(1T) Lot: Lot Number
LPN:
CAT: Intensity Bin
BIN: Refer to below information
(9D)MFG Date: Manufacturing Date
(P) Customer Item:
(V) Vendor ID:
(9D) Date Code: Date Code
DeptID:
Made In: Country of Origin
10
(ii) Avago Baby Label (Only available on bulk packaging)
RoHS Compliant
e3 max temp 260C
Lamps Baby Label
(1P) PART #: Part Number
(1T) LOT #: Lot Number
(9D)MFG DATE: Manufacturing Date
QUANTITY: Packing Quantity
C/O: Country of Origin
Customer P/N:
CAT: Intensity Bin
Supplier Code:
BIN: Refer to below information
DATECODE: Date Code
Acronyms and Definition:
BIN:
Example:
(i) Color bin only or VF bin only
(i) Color bin only or VF bin only
BIN: 2 (represent color bin 2 only)
(Applicable for part number with color bins but
without VF bin OR part number with VF bins and no
color bin)
BIN: VB (represent VF bin “VB”only)
(ii) Color bin incorporate with VF Bin
BIN: 2VB
OR
(ii) Color bin incorporated with VF Bin
VB: VF bin “VB”
(Applicable for part number that have both color
bin and VF bin)
2: Color bin 2 only
DISCLAIMER: AVAGO’S PRODUCTS AND SOFTWARE ARE NOT SPECIFICALLY DESIGNED, MANUFACTURED OR AUTHORIZED FOR SALE
AS PARTS, COMPONENTS OR ASSEMBLIES FOR THE PLANNING, CONSTRUCTION, MAINTENANCE OR DIRECT OPERATION OF A NUCLEAR
FACILITY OR FOR USE IN MEDICAL DEVICES OR APPLICATIONS. CUSTOMER IS SOLELY RESPONSIBLE, AND WAIVES ALL RIGHTS TO MAKE
CLAIMS AGAINST AVAGO OR ITS SUPPLIERS, FOR ALL LOSS, DAMAGE, EXPENSE OR LIABILITY IN CONNECTION WITH SUCH USE.
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2010 Avago Technologies. All rights reserved.
AV02-2459EN - April 20, 2010
相关型号：
HLMP-EG3A-VV0DD
Single Color LED, Red, Untinted, T-1 3/4, 5mm, ROHS COMPLIANT, PLASTIC PACKAGE-2
AVAGO
HLMP-EG3A-W10DD
Single Color LED, Red, Untinted, T-1 3/4, 5mm, ROHS COMPLIANT, PLASTIC PACKAGE-2
AVAGO
©2020 ICPDF网 联系我们和版权申明