HCPL-070L-500E [AVAGO]
Low Input Current, High Gain, LVTTL/LVCMOS Compatible Optocouplers; 低输入电流，高增益， LVTTL / LVCMOS兼容光电耦合器
| 型号： | HCPL-070L-500E |
| 厂家： | 
AVAGO TECHNOLOGIES LIMITED |
| 描述： | Low Input Current, High Gain, LVTTL/LVCMOS Compatible Optocouplers |
| 文件： | 总12页 (文件大小：250K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HCPL-270L/070L/273L/073L
Low Input Current, High Gain, LVTTL/LVCMOS Compatible Optocouplers
Data Sheet
Description
Features
• 3.3V/5V Dual Supply Voltages
These high gain series couplers use a Light Emitting Di-
ode and an integrated high gain photodetector to pro-
vide extremely high current transfer ratio between input
and output. Separate pins for the photodiode and out-
put stage result in LVTTL compatible saturation voltages
• Low power consumption
• High current transfer ratio
• Low input current requirements – 0.5 mA
• LVTTL/LVCMOS compatible output
• Performance guaranteed over temperature 0°C to +70°C
• Base access allows gain bandwidth adjustment
• High output current – 60 mA
and high speed operation. Where desired, the V and V
CC
O
terminals may be tied together to achieve conventional
photo-darlington operation. A base access terminal al-
lows a gain bandwidth adjustment to be made.
These optocouplers are for use in LVTTL/LVCMOS or
other low power applications. A 400% minimum current
transfer ratio is guaranteed over 0 to +70˚C operating
range for only 0.5 mA of LED current.
• Safety approval, UL, IEC/EN/DIN EN 60747-5-2, CSA
Applications
• Ground isolate most logic families – LVTTL/LVCMOS
• Low input current line receiver
• High voltage insulation
The HCPL-070L and HCPL-073L are surface mount de-
vices packaged in an industry standard SOIC-8 footprint.
The SOIC-8 does not require "through holes" in a PCB.
This package occupies approximately one-third the foot-
print area of the standard dual-in-line package. The lead
profile is designed to be compatible with standard sur-
face mount processes.
• EIA RS-232C line receiver
• Telephone ring detector
• V AC line voltage status indicator – low input power
dissipation
• Low power systems – ground isolation
Functional Diagram
HCPL-270L/070L
HCPL-273L/073L
8
7
6
5
NC
ANODE
CATHODE
NC
1
2
3
4
V
V
V
CC
B
1
2
3
4
8
7
6
5
V
V
V
ANODE
CATHODE
CATHODE
ANODE
CC
O1
O2
1
1
2
2
O
GND
GND
SHIELD
TRUTH TABLE
LED
V
O
ON
OFF
LOW
HIGH
A 0.1 µF bypass capacitor connected between pins 8 and 5 is recommended.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Ordering Information
HCPL-270L, HCPL-273L, HCPL-070L and HCPL-073L are UL Recognized with 3750 Vrms for 1 minute per UL1577 and
are approved under CSA Component Acceptance Notice #5, File CA 88324.
Option
Part
Number
RoHS
non RoHS
Surface
Mount
Gull
Wing
Tape
& Reel
UL 5000 Vrms/
1 Minute rating
IEC/EN/DIN
EN 60747-5-2 Quantity
Compliant Compliant Package
-000E
no option 300 mil DIP-8
50 per tube
HCPL-270L -300E
HCPL-273L -500E
-060E
-300
X
X
X
X
50 per tube
-500
X
X
X
X
1000 per reel
100 per tube
1500 per reel
100 per tube
1500 per reel
100 per tube
1500 per reel
-060
X
X
-560E
-560
X
X
X
X
X
X
-000E
no option SO-8
HCPL-070L -500E
HCPL-073L -060E
-560E
-500
-060
-560
X
X
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
HCPL-273L-500E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with
IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant.
Example 2:
HCPL-273L to order product of 300 mil DIP package in Tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation ‘#XXX’is used for existing products, while (new) products launched since July 15, 2001 and
RoHS compliant will use ‘–XXXE.’
2
Selection Guide
8-Pin DIP (300 Mil)
Small Outline SO-8
Single Channel
Package HCPL-
Dual Channel
Package HCPL-
Single Channel
Package HCPL-
Dual Channel
Package HCPL-
Minimum Input
ON Current (I )
Minimum CTR
F
270L
273L
070L
073L
0.5 mA
400%
Schematic
V
I
CC
CC
I
1
F1
8
V
CC
+
8
I
CC
V
F1
I
F
2
ANODE
+
-
I
O1
V
F
V
V
2
O1
O2
7
6
5
-
CATHODE
I
O
3
6
5
V
O
I
3
F2
-
I
O2
GND
V
SHIELD
F2
I
B
7
V
+
4
B
GND
SHIELD
USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED
BETWEEN PINS 5 AND 8 IS RECOMMENDED
HCPL-270L/HCPL-070L
HCPL-273L/HCPL-073L
3
Package Outline Drawings
8-Pin DIP Package
7.62 0.25
(0.300 0.010)
9.65 0.25
(0.380 0.010)
8
1
7
6
5
6.35 0.25
(0.250 0.010)
TYPE NUMBER
OPTION CODE*
DATE CODE
A XXXXZ
R U
YYWW
UL
2
3
4
RECOGNITION
1.78 (0.070) MAX.
1.19 (0.047) MAX.
+ 0.076
- 0.051
0.254
5° TYP.
+ 0.003)
- 0.002)
3.56 0.13
(0.140 0.005)
(0.010
4.70 (0.185) MAX.
0.51 (0.020) MIN.
2.92 (0.115) MIN.
DIMENSIONS IN MILLIMETERS AND (INCHES).
1.080 0.320
(0.043 0.013)
0.65 (0.025) MAX.
* MARKING CODE LETTER FOR OPTION NUMBERS
"L" = OPTION 020
2.54 0.25
(0.100 0.010)
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
Small Outline SO-8 Package
LAND PATTERN RECOMMENDATION
TYPE NUMBER
(LAST 3 DIGITS)
OPTION 060 CODE
8
7
6
5
4
5.994 0.203
(0.236 0.008)
XXXV
YWW
3.937 0.127
(0.155 0.005)
7.49 (0.295)
DATE CODE
1
2
3
PIN ONE
1.9 (0.075)
0.406 0.076
(0.016 0.003)
1.270
BSC
(0.050)
0.64 (0.025)
0.432
(0.017)
*
7°
5.080 0.127
(0.200 0.005)
45¡ X
3.175 0.127
(0.125 0.005)
0 ~ 7°
0.228 0.025
(0.009 0.001)
1.524
(0.060)
0.203 0.102
(0.008 0.004)
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 0.254 (0.205 0.010)
*
0.305
(0.012)
MIN.
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
OPTION NUMBER 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
4
Solder Reflow Temperature Profile
300
PREHEATING RATE 3°C + 1°C/-0.5°C/SEC.
REFLOW HEATING RATE 2.5°C 0.5°C/SEC.
PEAK
TEMP.
245°C
PEAK
TEMP.
240°C
PEAK
TEMP.
230°C
200
2.5°C 0.5°C/SEC.
SOLDERING
TIME
30
160°C
150°C
140°C
200°C
SEC.
30
SEC.
3°C + 1°C/-0.5°C
100
PREHEATING TIME
150°C, 90 + 30 SEC.
50 SEC.
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
0
0
50
100
150
200
250
TIME (SECONDS)
Note: Non-halide flux should be used.
Recommended Pb-Free IR Profile
TIMEWITHIN5°CofACTUAL
PEAKTEMPERATURE
t
p
20-40SEC.
260+0/-5°C
T
p
217°C
T
L
RAMP-UP
3°C/SEC.MAX.
RAMP-DOWN
6°C/SEC.MAX.
150-200°C
T
smax
T
smin
25
t
s
t
L
60to150SEC.
PREHEAT
60to180SEC.
t25°CtoPEAK
TIME
NOTES:
THETIME FROM 25 °C to PEAKTEMPERATURE = 8 MINUTES MAX.
= 200 °C, T = 150 °C
T
smax
smin
Note: Non-halide flux should be used.
Regulatory Information
The devices contained in this data sheet have been approved by the following organizations:
UL Approval under UL 1577, Component Recognition Program, File E55361.
CSA Approval under CSA Component Acceptance Notice #5, File CA 88324.
IEC/EN/DIN EN 60747-5-2
Approved under
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01 (Option 060 only)
5
Insulation and Safety Related Specifications
8-Pin DIP
(300 Mil)
Value
SO-8
Value
Parameter
Symbol
Units
Conditions
Minimum External Air
Gap (External Clearance)
L (101)
7.1
4.9
mm
Measured from input terminals to output
terminals, shortest distance through air.
Minimum External Tracking
(External Creepage)
L (102)
7.4
4.8
mm
mm
Measured from input terminals to output
terminals, shortest distance path along body.
Minimum Internal Plastic
Gap (Internal Clearance)
0.08
0.08
Through insulation distance, conductor to
conductor, usually the direct distance
between the photoemitter and photodetector
inside the optocoupler cavity.
Tracking Resistance
(Comparative Tracking
Index)
CTI
200
IIIa
200
IIIa
Volts
DIN IEC 112/VDE 0303 Part 1.
Isolation Group
Material Group (DIN VDE 0110, 1/89, Table 1).
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics
8-pin DIP
(300 mil)
Description
Symbol
SO-8
Units
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤ 150 V rms
I-IV
I-III
I-II
for rated mains voltage ≤ 300 V rms
for rated mains voltage ≤ 600 V rms
I-IV
I-III
Climatic Classification
55/100/21
55/100/21
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
2
2
VIORM
VPR
630
566
Vpeak
Vpeak
Input to Output Test Voltage, Method b*
VPR = 1.875 x VIORM, 100% Production Test with tP = 1 sec,
Partial Discharge < 5 pC
1181
1063
Input to Output Test Voltage, Method a*
VPR = 1.5 x VIORM, Type and Sample Test,
tP = 60 sec, Partial Discharge < 5 pC
VPR
945
849
Vpeak
Vpeak
Highest Allowable Overvoltage*
VIOTM
6000
4000
(Transient Overvoltage, tini = 10 sec)
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 11, Thermal Derating curve.)
Case Temperature
TS
175
400
600
150
150
600
˚C
mA
mW
Current (Input Current IF, PS = 0)
Output Power
IS,INPUT
PS,OUTPUT
Insulation Resistance at TS, VIO = 500 V
RS
≥ 109
≥ 109
Ω
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
6
Absolute Maximum Ratings (No Derating Required up to +85˚C)
Parameter
Symbol
TS
Min.
–55
–40
Max.
125
85
Units
˚C
Storage Temperature
Operating Temperature
Average Forward Input Current
TA
˚C
IF(AVG)
IF(PEAK)
20
mA
mA
Peak Forward Input Current
40
(50% Duty Cycle, 1 ms Pulse Width)
Peak Transient Input Current
(< 1 µs Pulse Width, 300 pps)
IF(TRAN)
1.0
A
Reverse Input Voltage
VR
PI
5
V
Input Power Dissipation
35
60
0.5
7
mW
mA
V
Output Current (Pin 6)
IO
Emitter Base Reverse Voltage (Pin 5-7)
Supply Voltage and Output Voltage
Output Power Dissipation
Total Power Dissipation
VEB
VCC
PO
PT
–0.5
V
100
135
mW
mW
Lead Solder Temperature
(for Through Hole Devices)
260˚C for 10 sec., 1.6 mm below seating plane.
Reflow Temperature Profile
(for SOIC-8 and Option #300)
See Package Outline Drawings section.
Recommended Operating Conditions
Parameter
Symbol
VCC
Min.
2.7
0.5
0
Max.
7.0
Units
V
Power Supply Voltage
Forward Input Current (ON)
Forward Input Voltage (OFF)
Operating Temperature
IF(ON)
VF(OFF)
TA
12.0
0.8
mA
V
0
70
˚C
7
Electrical Specifications
0˚C ≤ T ≤ +70˚C, 2.7 V ≤ V ≤ 3.3 V, 0.5 mA ≤ I
≤ 12 mA, 0 V ≤ V
≤ 0.8 V, unless otherwise specified.
A
CC
F(ON)
F(OFF)
All typicals at T = 25˚C. (See Note 8.)
A
Device
Sym. HCPL-
Parameter
Min. Typ.* Max. Units Test Conditions
Fig. Note
Current Transfer
Ratio
CTR
400
1300 5000
%
IF = 0.5 mA
VCC = 3.3 V
VO = 0.4 V
1, 2
2
Logic Low
Output Voltage
VOL
0.05
0.05
5
0.3
0.4
25
V
IF = 1.6 mA,
IO = 8 mA
VCC = 3.3 V
V
IF = 5.0 mA,
IO = 15 mA
Logic High
Output Current
IOH
µA
VO = VCC = 3.3 V
VCC = 3.3 V
VCC = 3.3 V
TA = 25˚C
IF = 0 mA
2
Logic Low
Supply Current
ICCL
ICCH
VF
270L/070L
273L/073L
0.4
0.8
1.3
2.7
mA
mA
IF1 = IF2 = 1.6 mA
VO1 = VO2 = Open
Logic High
Supply Current
270L/070L
273L/073L
0.002
0.002
1
2
µA
µA
IF1 = IF2 = 0 mA
VO1 = VO2 = Open
Input Forward
Voltage
1.5
1.7
V
IF = 1.6 mA
3, 4
Input Reverse
Breakdown Voltage
BVR
5.0
V
IR = 10 µA,
TA = 25˚C
2
2
Temperature Coefficient ∆VF/
-1.8
60
mV/°C IF = 1.6 mA
of ForwardVoltage
Input Capacitance
∆TA
CIN
pF f = 1 MHz, VF = 0
*All typical values at T = 25˚C and V = 3.3 V, unless otherwise noted.
A
CC
Electrical Specifications
0°C ≤ T ≤ 70°C, 4.5 V ≤ V ≤ 7 V, 0.5 mA ≤ I
≤ 12 mA, 0 V ≤ V ≤ 0.8 V, unless otherwise specified.
F(OFF)
A
CC
F(ON)
All Typicals at T = 25°C. (See note 8.)
A
Parameter
Sym. Device Min. Typ.* Max.
Units
Test Conditions
Fig. Note
CurrentTransfer Ratio
Logic Low OutputVoltage
CTR
VOL
300
1600
0.1
2600
0.4
250
3
%
IF = 1.6 mA, VCC = 4.5V, VO = 0.5V
IF = 1.6 mA, IO = 4.8 mA, VCC = 4.5V
VO =VCC = 7V, IF = 0 mA
2, 3
1
2
V
Logic High Output Current IOH
0.1
μA
mA
2
Logic Low
ICCL
ICCH
VF
0.9
VCC = 7V, IF1 = IF2 = 1.6 mA
V01 =V02 = Open
5
5
4
Supply Current
Logic High
0.004 20
μA
VCC = 7V, IF1 = IF2 = 0 mA,
V01 =V02 = Open
Supply Current
Input ForwardVoltage
1.4
1.7
V
V
TA = 25°C
1.75
IF = 1.6 mA
Input Reverse
BVR
5
V
IR = 10 μA, TA = 25°C
2
2
Breakdown Voltage
Temperature Coefficient
of ForwardVoltage
∆VF/
∆TA
-1.8
60
mV/°C IF = 1.6 mA
Input Capacitance
CIN
pF
f = 1 MHz, VF = 0
*All typical values at TA = 25°C and VCC = 5 V, unless otherwise noted.
8
Switching Specifications (AC)
Over Recommended Operating Conditions (T = 0˚C to +70˚C), V = 3.3 V, unless otherwise specified. (See Note 8.)
A
CC
Parameter
Sym.
Min.
Typ.* Max.
Units
Test Conditions
Fig.
Note
Propagation Delay
Time to Logic Low
at Output
tPHL
30
µs
IF = 0.5 mA, Rl = 4.7 kΩ
5
2
Propagation Delay
Time to Logic High
at Output
tPLH
90
µs
IF = 0.5 mA, RL = 4.7 kΩ
5
6
2
Common Mode
Transient Immunity
at Logic High
|CMH|
1000
1000
10000
V/µs
IF = 0 mA, TA = 25˚C,
Rl = 2.2 kΩ
|VCM| = 10 Vp-p
2, 6, 7
Level Output
Common Mode
Transient Immunity
at Logic Low
|CML|
10000
V/µs
IF = 1.6 mA, TA = 25˚C,
Rl = 2.2 kΩ
|VCM| = 10 Vp-p
6
2, 6, 7
Level Output
*All typical values at T = 25˚C and V = 3.3 V, unless otherwise noted.
A
CC
Switching Specifications (AC)
Over recommended operating conditions (T = 0°C to 70°C), V = 5 V, unless otherwise specified. (See note 8.)
A
CC
Parameter
Sym.
Min.
Typ.*
Max.
Units
Test Conditions
Fig.
Note
Propagation Delay
Time to LogicLow
at Output
tPHL
25
IF = 1.6 mA, RL = 2.2 kΩ
6, 7, 8, 9
2
Propagation Delay
Time to Logic High
at Output
tPLH
50
IF = 1.6 mA, RL = 2.2 kΩ
7, 8, 9
10
2
Common Mode Transient |CMH| 1000
Immunity at Logic
High Output
10000
10000
V/μs
V/μs
IF = 0 mA, TA = 25°C,
RL = 2.2 kΩ
|VCM| = 10 Vp-p
2, 6, 7
2, 6, 7
Common Mode Transient |CMH| 1000
Immunity at Logic
IF = 1.6 mA, TA = 25°C,
RL = 2.2 kΩ
10
Low Output
|VCM| = 10 Vp-p
*All typical values at TA = 25°C and VCC = 5 V, unless otherwise noted.
9
Package Characteristics
Parameter
Sym.
Device HCPL-
Min. Typ.* Max.
Units
Test Conditions
Fig. Note
Input-Output
Momentary
Withstand
Voltage**
VISO
3750
V rms
RH ≤ 50%,
t = 1 min.,
TA = 25˚C
4, 9
Resistance
(Input-Output)
RI-O
CI-O
II-I
1012
0.6
Ω
VI-O = 500 Vdc
RH ≤ 45%
4
Capacitance
(Input-Output)
pF
µA
f = 1 MHz
11
5
Input-Input
Insulation
0.005
RH ≤ 45%
VI-I = 500 Vdc
Leakage Current
Input-Input
Insulation
Leakage Current
RI-I
CI-I
1011
Ω
5
5
Capacitance
(Input-Input)
270L
273L
0.03
0.25
pF
070L
073L
*All typical values at TA = 25˚C, unless otherwise noted.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equip-
ment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage."
Notes:
1. Pin 5 should be the most negative voltage at the detector side.
2. Each channel.
3. DC CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, I , to the forward LED input current, I , times 100%.
O
F
4. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
5. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
6. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV /dt of the common mode pulse, V , to as-
CM
CM
sure that the output will remain in a Logic High state (i.e., V > 2.0 V). Common mode transient immunity in a Logic Low level is the
O
maximum tolerable (negative) dV /dt of the common mode pulse, V , to assure that the output will remain in a Logic Low state
CM
CM
(i.e., V < 0.8 V).
O
7. In applications where dV/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, R , should be included to protect the detector
CC
IC from destructively high surge currents. The recommended value is R = 110 Ω.
CC
8. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 adjacent to the device is recommended.
9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V rms for 1 second (leakage detec-
tion current limit, I < 5 µA).
I-O
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage detec-
tion current limit, I < 5 µA).
I-O
11. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
12. Derate linearly above 65˚C free-air temperature at a rate of 2.3 mW/˚C for the SO-8 package.
10
85°C
V
V
= 5.0 V
= 0.4 V
CC
O
2000
1600
1200
800
2500
2000
1500
1000
100
10
T
T
= 0° C
70°C
25°C
70°C
-40°C
A
A
= 25° C
T
T
T
= 70° C
= 85° C
= -40° C
A
A
A
T
= 85° C
A
1.0
T
T
T
= 70° C
= 25° C
= 0° C
A
A
A
V
V
= 3.3 V
= 0.4 V
0.1
CC
O
400
0
500
0
T
= -40° C
A
0.01
0.01
0.1
1.0
10
0.1
1.0
I - FORWARD CURRENT - mA
10
0.1
1
10
I - INPUT DIODE FORWARD CURRENT - mA
I - FORWARD CURRENT - mA
F
F
F
Figure 1. Current transfer ratio vs. forward
current
Figure 2. Current transfer ratio vs. forward
current
Figure 3. Output current vs. input diode
forward current
1.6
1000
100
I
V
V
= 5.0 V
= 0.4 V
F
CC
O
I = 1.6 mA
F
+
100
V
F
1.5
1.4
-
10
1.0
0.1
10
T
T
T
= 85° C
= 25° C
= -40° C
A
A
A
T
T
= 85°C
= 70°C
A
1.0
0.1
A
T
T
T
= 25°C
= 0°C
= -40°C
1.5
1.3
1.2
A
A
A
0.01
0.001
1.1
1.2
1.3
1.4
1.6
0.1
1
10
-60 -40 -20
0
20
40 60 80 100
I - INPUT DIODE FORWARD CURRENT - mA
V - FORWARD VOLTAGE - V
F
F
T
- TEMPERATURE - °C
A
Figure 4. Output current vs. input diode
forward current
Figure 5. Input diode forward current vs.
forward voltage
Figure 6. Forward voltage vs. temperature
I
F
I
PULSE
GEN.
F
0
8
7
6
5
3.3 V
1
2
3
4
Z
= 50 W
O
3.3 V
V
O
t = 5 ns
r
R
L
10% DUTY CYCLE
I/f < 100 µs
(SATURATED
RESPONSE)
50%
50%
V
O
V
OL
0.1 µF
I
MONITOR
F
t
t
PHL
PLH
C = 15 pF*
L
R
M
3.3 V
* INCLUDES PROBE AND
FIXTURE CAPACITANCE
V
O
90%
10%
90%
(NON-SATURATED
RESPONSE)
10%
t
f
t
r
Figure 7. Switching test circuit
I
PULSE GEN.
F
I
F
+5 V
1
2
3
4
8
7
6
5
Z
= 50 W
O
t = 5 ns
r
R
5 V
L
V
O
V
O
1.5 V
V
V
OL
t
PHL
C = 15 pF
L
0.1µF
I MONITOR
F
I
F
0
R
M
5 V
O
1.5 V
V
OL
t
PLH
Figure 8. Switching test circuit
R
(SEE NOTE 6)
CC
I
t , t = 16 ns
F
8
1
2
3
4
+3.3 V
r
f
10 V
90%
90%
V
CM
B
0 V
10%
10%
R
7
6
5
L
t
r
t
A
f
V
O
V
O
3.3 V
V
FF
SWITCH AT A: I = 0 mA
F
V
O
V
+
V
CM
OL
-
SWITCH AT B: I = 1.6 mA
F
PULSE GEN.
Figure 9. Test circuit for transient immunity and typical waveforms
I
F
R
(SEE NOTE 7)
R
B
CC
+5 V
1
2
3
4
8
7
6
5
110 W
A
t , t = 16 ns
r
f
L
10 V
V
CM
90% 90%
10%
10%
0 V
V
V
O
V
FF
t
t
f
r
0.1 µF
5 V
V
O
SWITCH AT A: I = 0 mA
F
V
O
OL
V
CM
SWITCH AT B: I = 1.6 mA
F
+
-
PULSE GEN.
Figure 10. Test circuit for transient immunity and typical waveforms
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.
Data subject to change. Copyright © 2005-2008 Avago Technologies Limited. All rights reserved. Obsoletes AV01-0544EN
AV02-1054EN - April 3, 2008
相关型号：
©2020 ICPDF网 联系我们和版权申明