HCPL-063L [AVAGO]
High Speed LVTTL Compatible 3.3 Volt Optocouplers Low power consumption; 高速LVTTL兼容3.3伏光电耦合器的低功耗型号: | HCPL-063L |
厂家: | AVAGO TECHNOLOGIES LIMITED |
描述: | High Speed LVTTL Compatible 3.3 Volt Optocouplers Low power consumption |
文件: | 总19页 (文件大小:333K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
HCPL-260L/060L/263L/063L
High Speed LVTTL Compatible 3.3 Volt Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
Features
The HCPL-260L/060L/263L/063L are optically coupled
gates that combine a GaAsP light emitting diode and
an integrated high gain photo detector. An enable in-
put allows the detector to be strobed. The output of
the detector IC is an open collector Schottky-clamped
transistor. The internal shield provides a guaranteed
common mode transient immunity specification of
15 kV/µs at 3.3V.
• 3.3V/5V Dual Supply Voltages
• Low power consumption
• 15 kV/µs minimum Common Mode Rejection (CMR) at
V
= 1000 V
CM
• High speed: 15 MBd typical
• LVTTL/LVCMOS compatible
• Low input current capability: 5 mA
This unique design provides maximum AC and DC circuit
isolation while achieving LVTTL/LVCMOS compati-bili-
ty. The optocoupler AC and DC operational parameters
are guaranteed from –40°C to +85°C allowing trouble-
free system performance.
• Guaranteed AC and DC performance over tempera-
ture: –40°C to +85°C
• Available in 8-pin DIP, SOIC-8
• Strobable output (single channel products only)
• Safety approvals: UL, CSA, IEC/EN/DIN EN 60747-5-5
These optocouplers are suitable for high speed logic
interfacing, input/output buffering, as line receivers in
environments that conventional line receivers cannot
tolerate and are recommended for use in extremely high
ground or induced noise environments.
Applications
• Isolated line receiver
• Computer-peripheral interfaces
• Microprocessor system interfaces
• Digital isolation for A/D, D/A conversion
• Switching power supply
• Instrument input/output isolation
• Ground loop elimination
• Pulse transformer replacement
• Field buses
Functional Diagram
HCPL-260L/060L
HCPL-263L/063L
1
2
V
V
V
ANODE
CATHODE
CATHODE
ANODE
1
2
V
V
8
7
8
7
NC
CC
CC
O1
O2
1
1
ANODE
E
V
CATHODE
NC
3
4
6
5
3
4
6
5
O
2
2
GND
GND
SHIELD
SHIELD
TRUTH TABLE
TRUTH TABLE
(POSITIVE LOGIC)
(POSITIVE LOGIC)
LED ENABLE OUTPUT
LED OUTPUT
ON
OFF
ON
OFF
ON
OFF
H
H
L
L
NC
NC
L
H
H
H
L
ON
OFF
L
H
A 0.1 µF bypass capacitor must be
connected between pins 5 and 8.
H
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Ordering Information
HCPL-xxxx is UL Recognized with 3750 Vrms for 1 minute per UL1577
Option
UL 5000
RoHS
Non RoHS
Gull
Tape
Surface
Vrms/ 1 Min-
ute rating
IEC/EN/DIN
EN 60747-5-5 Quantity
Part number Compliant Compliant Package Mount
Wing
& Reel
-000E
-300E
-500E
-020E
-320E
-520E
-060E
-560E
-000E
-300E
-500E
-020E
-320E
-520E
-060E
-560E
-000E
-500E
-060E
-560E
-000E
-500E
-060E
-560E
No option
-300
50 per tube
X
X
X
X
50 per tube
1000 per reel
50 per tube
50 per tube
1000 per reel
50 per tube
1000 per reel
50 per tube
50 per tube
1000 per reel
50 per tube
50 per tube
1000 per reel
50 per tube
1000 per reel
100 per tube
1500 per reel
100 per tube
1500 per reel
100 per tube
1500 per reel
100 per tube
1500 per reel
#500
X
-020
X
X
X
300mil
DIP-8
HCPL-260L
-320
X
X
X
X
-520
X
X
#060
X
X
#560
X
X
No option
#300
X
X
X
X
#500
X
#020
X
X
X
300mil
DIP-8
HCPL-263L
-320
X
X
X
X
#520
X
X
X
X
X
X
-060
X
X
-560
X
X
X
X
X
X
X
X
X
X
No option
#500
HCPL-060L
HCPL-063L
SO-8
SO-8
#060
X
X
-560
No option
#500
-060
X
X
-560
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry. Combination of Option 020 and Option 060 is not available.
Example 1:
HCPL-260L-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with
IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant.
Example 2:
HCPL-263L to order product of 300mil DIP package in tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and
RoHS compliant option will use ‘-XXXE‘.
2
Schematic
HCPL-263L/063L
HCPL-260L/060L
I
F
I
I
CC
I
CC
I
V
V
V
V
CC
O
CC
O1
8
6
8
7
2+
1
+
I
F1
O1
O
V
V
F1
–
2
V
F
–
3
GND
SHIELD
SHIELD
5
SHIELD
I
E
7
E
3
–
V
I
O2
V
O2
6
5
USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED
F2
BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 5).
+
4
I
F2
GND
Package Outline Drawings
8-Pin DIP Package
7.63 0.35
9.65 0.35
(0.ꢀ00 0.010ꢁ
(0.ꢀ80 0.010ꢁ
8
1
7
6
5
6.ꢀ5 0.35
TYPE NUMBER
OPTION CODE*
DATE CODE
(0.350 0.010ꢁ
A XXXXZ
YYWW
U R
UL
3
ꢀ
4
RECOGNITION
1.78 (0.070ꢁ MAX.
1.19 (0.047ꢁ MAX.
+ 0.076
0.354
5 TYP.
- 0.051
+ 0.00ꢀꢁ
ꢀ.56 0.1ꢀ
(0.010
4.70 (0.185ꢁ MAX.
0.51 (0.030ꢁ MIN.
- 0.003ꢁ
(0.140 0.005ꢁ
3.93 (0.115ꢁ MIN.
DIMENSIONS IN MILLIMETERS AND (INCHESꢁ.
1.080 0.ꢀ30
0.65 (0.035ꢁ MAX.
(0.04ꢀ 0.01ꢀꢁ
* MARKING CODE LETTER FOR OPTION NUMBERS
3.54 0.35
"V" = OPTION 060
(0.100 0.010ꢁ
OPTION NUMBER 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.35 mm (10 milsꢁ MAX.
3
8-Pin DIP Package with Gull Wing Surface Mount in Option 500
(HCPL-260L, HCPL-263L)
LAND PATTERN RECOMMENDATION
9.65 0.ꢀ5
ꢁ.0ꢁ6 (0.040ꢂ
(0.380 0.0ꢁ0ꢂ
6
5
4
8
ꢁ
7
6.350 0.ꢀ5
ꢁ0.9 (0.430ꢂ
ꢀ.0 (0.080ꢂ
(0.ꢀ50 0.0ꢁ0ꢂ
ꢀ
3
ꢁ.ꢀ7 (0.050ꢂ
9.65 0.ꢀ5
ꢁ.780
(0.380 0.0ꢁ0ꢂ
(0.070ꢂ
MAX.
ꢁ.ꢁ9
(0.047ꢂ
MAX.
7.6ꢀ 0.ꢀ5
(0.300 0.0ꢁ0ꢂ
0.076
0.ꢀ54
0.05ꢁ
3.56 0.ꢁ3
(0.ꢁ40 0.005ꢂ
0.003
(0.0ꢁ0
0.00ꢀꢂ
ꢁ.080 0.3ꢀ0
(0.043 0.0ꢁ3ꢂ
0.635 0.ꢀ5
(0.0ꢀ5 0.0ꢁ0ꢂ
ꢁꢀ NOM.
0.635 0.ꢁ30
(0.0ꢀ5 0.005ꢂ
ꢀ.54
(0.ꢁ00ꢂ
BSC
DIMENSIONS IN MILLIMETERS (INCHESꢂ.
LEAD COPLANARITY = 0.ꢁ0 mm (0.004 INCHESꢂ.
NOTE: FLOATING LEAD PROTRUSION IS 0.ꢀ5 mm (ꢁ0 milsꢂ MAX.
Small Outline SO-8 Package
LAND PATTERN RECOMMENDATION
8
7
2
6
5
4
5.994 ꢀ.2ꢀ3
(ꢀ.236 ꢀ.ꢀꢀ8ꢁ
XXXV
YWW
3.937 ꢀ.127
(ꢀ.155 ꢀ.ꢀꢀ5ꢁ
TYPE NUMBER
7.49 (0.295)
(LAST 3 DIGITSꢁ
DATE CODE
1
3
PIN ONE
1.9 (0.075)
ꢀ.4ꢀ6 ꢀ.ꢀ76
(ꢀ.ꢀ16 ꢀ.ꢀꢀ3ꢁ
1.27ꢀ
(ꢀ.ꢀ5ꢀꢁ
BSC
0.64 (0.025)
ꢀ.432
*
7
5.ꢀ8ꢀ ꢀ.127
45 X
(ꢀ.ꢀ17ꢁ
(ꢀ.2ꢀꢀ ꢀ.ꢀꢀ5ꢁ
3.175 ꢀ.127
(ꢀ.125 ꢀ.ꢀꢀ5ꢁ
ꢀ ~ 7
ꢀ.228 ꢀ.ꢀ25
(ꢀ.ꢀꢀ9 ꢀ.ꢀꢀ1ꢁ
1.524
(ꢀ.ꢀ6ꢀꢁ
ꢀ.2ꢀ3 ꢀ.1ꢀ2
(ꢀ.ꢀꢀ8 ꢀ.ꢀꢀ4ꢁ
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASHꢁ
5.2ꢀ7 ꢀ.254 (ꢀ.2ꢀ5 ꢀ.ꢀ1ꢀꢁ
*
ꢀ.3ꢀ5
(ꢀ.ꢀ12ꢁ
MIN.
DIMENSIONS IN MILLIMETERS (INCHESꢁ.
LEAD COPLANARITY = ꢀ.1ꢀ mm (ꢀ.ꢀꢀ4 INCHESꢁ MAX.
OPTION NUMBER 5ꢀꢀ NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS ꢀ.15 mm (6 milsꢁ MAX.
4
Reflow Soldering Profile
Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used.
Regulatory Information
The HCPL-260L/060L/263L/063L have been approved by the following organizations:
UL
Approval under UL 1577, Component Recognition Program, File E55361.
CSA
Approval under CSA Component Acceptance Notice #5, File CA 88324.
IEC/EN/DIN EN 60747-5-5
Insulation and Safety Related Specifications
8-Pin DIP
(300 Mil) SO-8
Parameter
Symbol
Value
Value
Units
Conditions
Minimum External Air
Gap (External Clearance)
L (101)
7.1
4.9
mm
Measured from input terminals to output
terminals, shortest distance through air.
Minimum External Tracking
(External Creepage)
L (102)
7.4
4.8
mm
mm
Measured from input terminals to output
terminals, shortest distance path along body.
Minimum Internal Plastic
Gap (Internal Clearance)
0.08
0.08
Through insulation distance, conductor
to conductor, usually the direct distance
between the photoemitter and
photodetector inside the optocoupler cavity.
Tracking Resistance
(Comparative Tracking Index)
CTI
200
IIIa
200
IIIa
Volts
DIN IEC 112/VDE 0303 Part 1
Isolation Group
Material Group (DIN VDE 0110, 1/89, Table 1)
5
IEC/EN/DIN EN 60747-5-5 Insulation Characteristics*
Description
Symbol
PDIP Option 060
SO-8 Option 060
Unit
Installation classification per DIN VDE 0110, Table 1
for rated mains voltage ≤ 150 Vrms
I – IV
I – IV
I – III
I – IV
I – IV
I – III
for rated mains voltage ≤ 300 Vrms
for rated mains voltage ≤ 600 Vrms
Climatic Classification
40/85/21
2
40/85/21
2
Pollution Degree (DIN VDE 0110/39)
Maximum Working Insulation Voltage
VIORM
VPR
630
567
Vpeak
Vpeak
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test with tm=1 sec,
Partial discharge < 5 pC
1181
1063
Input to Output Test Voltage, Method a*
VIORM x 1.6 = VPR, Type and Sample Test, tm=10 sec, Partial
discharge < 5 pC
VPR
1008
6000
907
Vpeak
Vpeak
Highest Allowable Overvoltage
VIOTM
6000
(Transient Overvoltage tini = 60 sec)
Safety-limiting values
– maximum values allowed in the event of a failure.
Case Temperature
TS
175
230
600
≥109
150
150
600
≥109
°C
Input Current
IS, INPUT
PS, OUTPUT
RS
mA
mW
W
Output Power
Insulation Resistance at TS, VIO = 500 V
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
Thermal Derating Curve Figures
HCPL-060L/HCPL-063L
HCPL-260L/HCPL-263L
(mW)
800
700
600
500
400
300
200
100
0
800
700
600
500
400
300
200
100
0
P
S
(mW)
P
S
S
I
(mA)
I (mA)
S
0
25 50 75 100 125 150 175 200
– CASE TEMPERATURE – C
0
25 50 75 100 125 150 175 200
T – CASE TEMPERATURE – C
S
T
S
6
Absolute Maximum Ratings (No Derating Required up to 85˚C)
Parameter
Symbol
Package**
Min.
–55
–40
Max.
125
85
Units
˚C
Note
Storage Temperature
Operating Temperature†
Average Forward Input Current
TS
TA
IF
˚C
Single 8-Pin DIP
Single SO-8
20
mA
2
Dual 8-Pin DIP
Dual SO-8
15
1, 3
1
Reverse Input Voltage
VR
PI
8-Pin DIP, SO-8
5
V
Input Power Dissipation
40
mW
V
Supply Voltage (1 Minute Maximum)
VCC
VE
7
Enable Input Voltage (Not to Exceed
VCC by more than 500 mV)
Single 8-Pin DIP
Single SO-8
VCC + 0.5
V
Enable Input Current
IE
5
mA
mA
V
Output Collector Current
Output Collector Voltage
Output Collector Power Dissipation
IO
50
7
1
1
VO
PO
Single 8-Pin DIP
Single SO-8
85
mW
Dual 8-Pin DIP
Dual SO-8
60
1, 4
**Ratings apply to all devices except otherwise noted in the Package column.
Recommended Operating Conditions
Parameter
Symbol
Min.
0
Max.
250
15
Units
µA
Input Current, Low Level
Input Current, High Level[1]
Power Supply Voltage
IFL*
IFH**
VCC
5
mA
V
2.7
4.5
3.6
5.5
Low Level Enable Voltage
High Level Enable Voltage
Operating Temperature
Fan Out (at RL = 1 kΩ)[1]
Output Pull-up Resistor
VEL
VEH
TA
0
0.8
VCC
85
5
V
2.0
–40
V
˚C
N
TTL Loads
Ω
RL
330
4 k
*The off condition can also be guaranteed by ensuring that V ≤ 0.8 volts.
FL
**The initial switching threshold is 5 mA or less. It is recommended that 6.3 mA to 10 mA be
used for best performance and to permit at least a 20% LED degradation guardband.
7
Electrical Specifications
Over Recommended Operating Conditions (T = –40°C to +85°C , 2.7V ≤ V ≤ 3.6V) unless otherwise specified.
A
CC
All Typicals at V = 3.3 V, T = 25°C. All enable test conditions apply to single channel products only. See Note 5.
CC
A
Parameter
Sym.
Device Min.
Typ.
Max.
Units
Test Conditions
Fig.
Note
High Level
Output Current
IOH*
4.5
50
µA
VCC = 3.3 V, VE = 2.0 V,
VO = 3.3 V, IF = 250 µA
1
1, 15
Input Threshold
Current
ITH
3.0
5.0
0.6
mA
V
VCC = 3.3 V, VE = 2.0 V,
VO = 0.6 V,
IOL (Sinking) = 13 mA
2
3
15
15
Low Level
Output Voltage
VOL
*
0.35
VCC = 3.3 V, VE = 2.0 V,
IF = 5 mA,
IOL (Sinking) = 13 mA
High Level
ICCH
ICCL
IEH
Single
Dual
4.7
6.9
7.0
8.7
–0.5
7.0
mA
mA
VE = 0.5 V IF = 0 mA
VCC = 3.3 V
Supply Current
Low Level
10.0
10.0
15.0
–1.2
Single
Dual
VE = 0.5 V IF = 10 mA
VCC = 3.3 V
Supply Current
High Level
Enable Current
Single
mA
mA
V
VCC = 3.3 V, VE = 2.0 V
Low Level
Enable Current
IEL*
Single
–0.5
–1.2
VCC = 3.3 V, VE = 0.5 V
High Level
Enable Voltage
VEH
VEL
VF
Single 2.0
15
Low Level
Enable Voltage
Single
1.4
0.8
V
Input Forward
Voltage
1.5
1.75*
V
TA = 25˚C, IF = 10 mA
IR = 10 µA
5
1
1
Input Reverse
Breakdown
Voltage
BVR*
5
V
Input Diode
Temperature
Coefficient
∆VF/
∆TA
–1.6
60
mV˚C
pF
IF = 10 mA
1
1
Input
CIN
f = 1 MHz, VF = 0 V
Capacitance
*The JEDEC Registration specifies 0˚C to +70˚C. Avago specifies –40˚C to +85˚C.
8
Electrical Specifications (DC)
Over recommended operating conditions (T = -40°C to +85°C, 4.5V ≤ V ≤ 5.5V) unless otherwise specified.
A
DD
All typicals at V = 5 V, T = 25 °C.
CC
A
Parameter
Symbol Channel Min. Typ.*
Max.
Units
Test Conditions
Fig.
Note
High Level Output
Current
IOH
5.5
100
mA
VCC = 5.5 V,
VO = 5.5 V,
IFL = 250 mA
1
1,15
Input Threshold
Current
ITH
Single
Dual
2.0
5.0
mA
VCC = 5.5 V, VO = 0.6 V,
IOL > 13 mA
2
3
15
15
2.5
Low Level Output
Voltage
VOL
0.35
0.6
V
VCC = 5.5 V, IF = 5 mA,
IOL(Sinking) = 13 mA
High Level Supply
Current
ICCH
Single
7.0
6.5
10.0
mA
mA
VE =0.5V, VCC = 5.5 V,
IF = 0 mA
VE =VCC, VCC = 5.5 V,
IF = 0 mA
Dual
10.0
9.0
15.0
13.0
VCC = 5.5 V, IF = 0 mA
Low Level Supply
Current
ICCL
Single
mA
mA
VE =0.5V, VCC = 5.5 V,
IF = 0 mA
8.5
VE =VCC, Vv = 5.5 V,
IF = 0 mA
Dual
13.0
-0.7
21.0
-1.6
mA
mA
VCC = 5.5 V, IF = 0 mA
VCC = 5.5 V, VE = 2.0V
High Level Enable
Current
IEH
IEL
Single
Low Level Enable
Current
Single
Single
Single
-0.9
1.5
-1.6
mA
V
VCC = 5.5 V, VE = 0.5V
High Level Enable
Voltage
VEH
VEL
VF
2.0
15
5
Low Level Enable
Voltage
0.8
V
Input Forward
Voltage
1.4
1.3
5
1.75
1.8
V
V
V
TA = 25 °C, IF = 10 mA
IF=10mA
Input Reverse
Breakdown Voltage
BVR
IR = 10 μA
1
1
Input Diode
Temperature
Coefficient
ΔVF/ΔTA
-1.6
60
mV/°C
IF = 10 mA
Input Capacitance
CIN
pF
f = 1 MHz, VF = 0 V
1
9
Switching Specifications
Over Recommended Operating Conditions (T = –40°C to +85°C, 2.7V ≤ V ≤ 3.6V), I = 7.5 mA unless otherwise
A
CC
F
specified. All Typicals at T = 25°C, V = 3.3 V.
A
CC
Parameter
Symbol
Min.
Typ. Max.
Units Test Conditions
Fig.
Note
Propagation Delay
Time to High Output
Level
tPLH
90
ns
RL = 350 Ω
CL = 15 pF
6, 7
1, 6, 15
Propagation Delay
Time to Low Output
Level
tPHL
75
ns
RL = 350 Ω
CL = 15 pF
1, 7, 15
Pulse Width
Distortion
|tPHL
tPLH
–
25
ns
ns
ns
ns
ns
RL = 350 Ω
CL = 15 pF
8
9, 15
8, 9, 15
1, 15
1, 15
10
|
Propagation Delay
Skew
tPSK
40
RL = 350 Ω
CL = 15 pF
Output Rise Time
(10-90%)
tr
45
20
45
RL = 350 Ω
CL = 15 pF
Output Fall Time
(90-10%)
tf
RL = 350 Ω
CL = 15 pF
Propagation Delay
Time of Enable from
VEH to VEL
tELH
RL = 350 Ω,
CL = 15 pF,
VEL = 0 V, VEH = 3 V
9
9
Propagation Delay
Time of Enable from
VEL to VEH
tEHL
30
ns
RL = 350 Ω,
CL = 15 pF,
VEL = 0 V, VEH = 3 V
11
Switching Specifications (AC)
Over recommended operating conditions T = -40°C to 85°C, 4.5 ≤ Vcc ≤ 5.5V, I = 7.5 mA unless otherwise specified.
A
F
All typicals at V = 5 V, T = 25 °C.
CC
A
Parameter
Symbol
Min.
Typ. Max.
Units Test Conditions
Fig.
Note
Propagation Delay Time
to High Output Level
tPLH
20
48
50
3.5
75
ns
TA = 25°C, RL = 350W,
6,7
1,6,15
CL = 15 pF
100
75
Propagation Delay Time
to Low Output Level
tPHL
25
ns
TA = 25°C, RL = 350W,
6, 7
8
1,7, 15
CL = 15 pF
100
35
Pulse Width Distortion
|tPHL - tPLH
|
ns
ns
ns
ns
ns
RL = 350W,
CL = 15 pF
9, 15
8,9, 15
1,15
1, 15
10
Propagation Delay
Skew
TPSK
tr
40
RL = 350W,
CL = 15 pF
Output Rise Time
(10%-90%)
24
10
30
RL = 350W,
CL = 15 pF
Output Fall Time
(10%-90%)
tf
RL = 350W,
CL = 15 pF
Propagation Delay
Time of Enable from
VEH to VEL
tELH
RL = 350W, CL = 15 pF,
VEL=0V, VEH=3V
9
9
Propagation Delay
Time of Enable from
VEL to VEH
tEHL
20
ns
RL = 350W, CL = 15 pF,
VEL=0V, VEH=3V
11
10
Parameter
Sym.
Device
Min.
Typ.
Units
Test Conditions
Fig.
Note
Output High Level
Common Mode
Transient Immunity
|CMH|
HCPL-263L
HCPL-063L
HCPL-260L
HCPL-060L
15
25
kV/ms
VCC = 3.3 V, IF = 0 mA,
VO(MIN) = 2 V, RL = 350 W,
TA = 25°C, VCM = 1000 V
and VCM = 10V
10
12,
14,
15
Output Low Level
Common Mode
Transient Immunity
|CML|
|CMH|
|CML|
HCPL-263L
HCPL-063L
HCPL-260L
HCPL-060L
15
10
10
25
15
15
kV/ms
kV/ms
kV/ms
VCC = 3.3 V, IF = 7.5 mA,
VO(MAX) = 0.8 V, RL = 350 W,
TA = 25°C, VCM = 1000 V
and VCM = 10V
10
10
10
13,
14,
15
Output High Level
Common Mode
Transient Immunity
HCPL-263L
HCPL-063L
HCPL-260L
HCPL-060L
VCC = 5 V, IF = 0 mA,
VO(MIN) = 2 V, RL = 350 W,
TA = 25°C, VCM = 1000 V
12,
14,
15
Output Low Level
Common Mode
Transient Immunity
HCPL-263L
HCPL-063L
HCPL-260L
HCPL-060L
VCC = 5 V, IF = 7.5 mA,
VO(MAX) = 0.8 V, RL = 350 W,
TA = 25°C, VCM = 1000 V
13,
14,
15
11
Package Characteristics
All Typicals at T = 25˚C.
A
Parameter
Sym.
Package
Min. Typ.
Max
Units
Test Conditions
Fig. Note
Input-Output
Insulation
II-O*
Single 8-Pin DIP
Single SO-8
1
µA
45% RH, t = 5 s,
VI-O = 3 kV DC, TA = 25˚C
16, 17
Input-Output
Momentary
Withstand
Voltage**
VISO
8-Pin DIP, SO-8
3750
V rms
RH ≤ 50%, t = 1 min,
TA = 25˚C
16, 17
Input-Output
Resistance
RI-O
CI-O
II-I
8-Pin, SO-8
1012
0.6
Ω
VI-O =500 V dc
1, 16, 19
1, 16, 19
20
Input-Output
Capacitance
8-Pin DIP, SO-8
Dual Channel
pF
µA
f = 1 MHz, TA = 25˚C
Input-Input
Insulation
Leakage
0.005
RH ≤ 45%, t = 5 s,
VI-I = 500 V
Current
Resistance
(Input-Input)
RI-I
CI-I
Dual Channel
1011
Ω
20
20
Capacitance
(Input-Input)
Dual 8-Pin Dip
Dual SO-8
0.03
0.25
pG
f = 1 MHz
*The JEDEC Registration specifies 0˚C to +70˚C. Avago specifies –40˚C to +85˚C.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table (if applicable), your equip-
ment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage."
Notes:
1. Each channel.
2. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not
exceed 20 mA.
3. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not
exceed 15 mA.
4. Derate linearly above +80˚C free-air temperature at a rate of 2.7 mW/˚C for the SOIC-8 package.
5. Bypassing of the power supply line is required, with a 0.1 µF ceramic disc capacitor adjacent to each optocoupler as illustrated in
Figure 11. Total lead length between both ends of the capacitor and the isolator pins should not exceed 20 mm.
6. The t
propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge
PLH
of the output pulse.
7. The t
propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge
PHL
of the output pulse.
8. t is equal to the worst case difference in t
and/or t
that will be seen between units at any given temperature and specified test
PSK
PHL
PLH
conditions.
9. See test circuit for measurement details.
10. The t
enable propagation delay is measured from the 1.5 V point on the falling edge of the enable input pulse to the 1.5 V point on the
ELH
rising edge of the output pulse.
11. The t enable propagation delay is measured from the 1.5 V point on the rising edge of the enable input pulse to the 1.5 V point on the
EHL
falling edge of the output pulse.
12. CM is the maximum tolerable rate of rise on the common mode voltage to assure that the output will remain in a high logic state
H
(i.e., V > 2.0 V).
o
13. CM is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state
L
(i.e., V < 0.8 V).
14. For sinusoidal voltages, (|dV | / dt)
o
= πf
V
(p-p).
CM
max
CM CM
15. No external pull up is required for a high logic state on the enable input. If the V pin is not used, tying V to V will result in improved
E
E
CC
CMR performance. For single channel products only. See application information provided.
16. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
17. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for one second (leakage
detection current limit, I ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
I-O
EN/DIN EN 60747-5-5 Insulation Characteristics Table, if applicable.
18. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for one second (leakage
detection current limit, I ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
I-O
EN/DIN EN 60747-5-5 Insulation Characteristics Table, if applicable.
19. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together. For dual channel products only.
20. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. For dual channel products only.
12
15
10
15
10
V
V
V
= 3.3 V
V
V
V
= 5.5 V
= 5.5 V
= 2.0 V*
= 250 µA
CC
O
E
CC
O
E
= 3.3 V
= 2.0 V*
= 250 µA
I
I
F
F
* FOR SINGLE
CHANNEL
PRODUCTS
ONLY
* FOR SINGLE
CHANNEL
PRODUCTS
ONLY
5
0
5
0
-60 -40 -20
0
20 40 60 80 100
-60 -40 -20
0
20 40 60 80 100
T
– TEMPERATURE – C
T
– TEMPERATURE – C
A
A
Figure 1. Typical high level output current vs. temperature.
8-PIN DIP, SO-8
8-PIN DIP, SO-8
6
12
10
V
V
= 5.0 V
CC
= 0.6 V
V
V
= 3.3 V
CC
= 0.6 V
O
O
5
4
3
2
8
6
4
R
= 350 Ω
R
= 350 KΩ
= 4 KΩ
L
L
R
= 1 KΩ
R
= 1 KΩ
L
L
1
0
2
0
R
= 4 KΩ
R
L
L
-60 -40 -20
0
20 40
80 100
-60 -40 -20
0
20 40
80 100
60
60
T
– TEMPERATURE – C
A
T
– TEMPERATURE – C
A
Figure 2. Typical output voltage vs. forward input current.
8-PIN DIP, SO-8
8-PIN DIP, SO-8
0.8
0.8
0.7
V
V
I
= 5.5 V * FOR SINGLE
CC
= 2.0 V*
E
V
V
F
= 3.3 V * FOR SINGLE
CC
CHANNEL
PRODUCTS ONLY
= 2.0 V*
CHANNEL
0.7
0.6
0.5
0.4
0.3
0.2
E
= 5.0 mA
I
= 5.0 mA
PRODUCTS ONLY
F
0.6
0.5
0.4
0.3
0.2
I
= 16 mA
= 9.6 mA
O
I
= 12.8 mA
= 6.4 mA
O
I
I
= 13 mA
O
I
O
O
0.1
0
0.1
0
-60 -40 -20
0
20 40
80 100
-60 -40 -20
0
20 40
80 100
60
60
T
– TEMPERATURE – C
T
– TEMPERATURE – C
A
A
Figure 3. Typical low level output voltage vs. temperature.
13
70
60
50
70
60
50
V
V
V
= 5.0 V
* FOR SINGLE
CHANNEL
V
V
V
= 3.3 V
* FOR SINGLE
CHANNEL
CC
E
CC
= 2.0 V*
= 0.6 V
OL
= 2.0 V*
E
PRODUCTS ONLY
= 0.6 V
PRODUCTS ONLY
OL
I
= 10-15 mA
F
I
= 5.0 mA
F
I
= 5.0 mA
F
40
20
40
20
-60 -40 -20
0
20 40
80 100
-60 -40 -20
0
20 40
80 100
60
60
T
– TEMPERATURE – C
T
– TEMPERATURE – C
A
A
Figure 4. Typical low level output current vs. temperature.
8-PIN DIP, SO-8
1000
T
= 25 C
A
100
10
I
+
F
F
V
–
1.0
0.1
0.01
0.001
1.1
1.2
1.3
1.4
1.5
1.6
V
– FORWARD VOLTAGE – V
F
Figure 5. Typical input diode forward characteristic.
PULSE GEN.
Z
f
= 50 Ω
O
t
= t = 5 ns
r
SINGLE CHANNEL
3.3V or 5V
DUAL CHANNEL
3.3V or 5V
I
F
I
F
PULSE GEN.
V
V
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
CC
CC
Z
= 50 Ω
O
R
L
t
= t = 5 ns
r
f
INPUT
OUTPUT V
O
0.1 µF
BYPASS
R
MONITORING
NODE
MONITORING
NODE
L
0.1 µF
OUTPUT V
INPUT
O
BYPASS
MONITORING
NODE
MONITORING
NODE
*C
L
R
C *
L
M
R
M
GND
GND
*C IS APPRO IMATELY 15
F
HICH INCLUDES
L
PROBE AND STRAY IRING CAPACITANCE.
I
I
= 7.50
A
A
F
INPUT
= 3.75
F
I
F
t
t
PLH
PHL
OUTPUT
V
O
1.5 V
Figure 6. Test circuit for tPHL and tPLH
.
14
100
80
150
120
V
F
= 5.0 V
CC
= 7.5 mA
V
F
= 3.3 V
CC
= 7.5 mA
I
I
t
, R = 4 KΩ
L
PLH
t
, R = 350 Ω
PHL
L
t
, R = 350 Ω
L
1 KΩ
4 KΩ
PLH
60
40
90
60
t
, R = 1 KΩ
L
PLH
t
, R = 350 Ω
L
PHL
t
, R = 350 Ω
L
PLH
20
0
30
0
-60 -40 -20
0
20 40
80 100
-60 -40 -20
0
20 40
80 100
60
60
T
– TEMPERATURE – C
T
- TEMPERATURE - ¡C
A
A
Figure 7. Typical propagation delay vs. temperature.
40
30
20
10
0
50
V
F
= 3.3 V
CC
= 7.5 mA
R
= 4 kΩ
L
I
40
30
20
10
0
V
F
= 5.0 V
CC
= 7.5 mA
I
R
= 350Ω
R
= 350 Ω
L
L
R
= 1 kΩ
L
-10
-60
-40 -20
0
20 40
80 100
60
-60
-40 -20
0
20 40
80 100
60
T
- TEMPERATURE - oC
T
– TEMPERATURE – C
A
A
Figure8. Typical pulse width distortion vs. temperature.
15
PULSE GEN.
= 50 Ω
Z
f
O
t = t = 5 ns
r
INPUT V
E
MONITORING NODE
3.3V or 5V
R
V
3.0 V
1.5 V
1
2
3
4
8
7
6
5
CC
INPUT
V
7.5 mA
F
E
0.1 µF
L
BYPASS
I
t
t
ELH
EHL
OUTPUT V
O
OUTPUT
MONITORING
NODE
V
O
1.5 V
*C
L
GND
*C IS APPROXIMATELY 15 pF WHICH INCLUDES
L
PROBE AND STRAY WIRING CAPACITANCE.
Figure 9. Test circuit for tEHL and tELH
.
I
F
SINGLE CHANNEL
DUAL CHANNEL
B
A
I
F
V
V
1
2
3
4
8
7
6
5
3.3V or 5V
OUTPUT V
1
2
3
4
8
7
6
5
3.3V or 5V
OUTPUT V
CC
CC
R
B
A
L
O
0.1 µF
R
MONITORING
NODE
L
BYPASS
V
FF
O
V
0.1 µF
FF
MONITORING
NODE
BYPASS
GND
GND
V
V
CM
CM
+
–
+
–
PULSE
PULSE
GENERATOR
GENERATOR
Z
= 50 Ω
Z = 50 Ω
O
O
V
PEA
CM
V
CM
0 V
5 V
S
S
ITCH AT A
ITCH AT B
I = 0
F
A
CM
H
V
O
V
= 7.5
MIN.
O
I
A
F
V
MA .
O
V
O
0.5 V
CM
L
Figure 10. Test circuit for common mode transient immunity and typical waveforms.
GND BUS (BACK)
V
BUS (FRONT)
NC
CC
ENABLE
OUTPUT
0.1µF
NC
10 mm MAX.
SINGLE CHANNEL
DEVICE ILLUSTRATED.
(SEE NOTE 5)
Figure 11. Recommended printed circuit board layout.
16
SINGLE CHANNEL DEVICE
3.3 V or 5V
3.3 V or 5V
8
6
V
CC1
V
CC2
R
L
220 Ω
I
F
+
2
3
D1*
V
0.1 µF
F
BYPASS
–
5
GND 1
GND 2
SHIELD
V
E
7
1
2
*DIODE D1 (1N916 OR EQUIVALENT) IS NOT REQUIRED FOR UNITS WITH OPEN COLLECTOR OUTPUT.
DUAL CHANNEL DEVICE
CHANNEL 1 SHOWN
3.3 V or 5V
3.3 V or 5V
8
7
V
CC1
V
CC2
R
L
220 Ω
I
F
+
1
2
D1*
V
0.1 µF
F
BYPASS
–
5
GND 1
GND 2
SHIELD
1
2
Figure 12. Recommended LVTTL interface circuit.
17
Application Information
Common-Mode Rejection for HCPL-260L Families:
Also, common-mode transients can capacitively cou-
ple from the LED anode (or cathode) to the output-side
ground causing current to be shunted away from the
LED (which can be bad if the LED is on) or conversely
cause current to be injected into the LED (bad if the LED
is meant to be off). Figure 14 shows the parasitic capaci-
tances which exists between LED anode/cathode and
Figure 13 shows the recommended drive circuit for op-
timal common-mode rejection performance. Two main
points to note are:
1. The enable pin is tied to V rather than floating (this
CC
applies to single-channel parts only).
2. Two LED-current setting resistors are used instead of
one. This is to balance I
mode transients.
variation during common-
LED
output ground (C and C ). Also shown in Figure 14 on
LA
LC
the input side is an AC-equivalent circuit.
If the enable pin is left floating, it is possible for common-
mode transients to couple to the enable pin, resulting in
common-mode failure. This failure mechanism only oc-
curs when the LED is on and the output is in the Low
State. It is identified as occurring when the transient out-
put voltage rises above 0.8 V. Therefore, the enable pin
For transients occurring when the LED is on, common-
mode rejection (CMR , since the output is in the “low”
L
state) depends upon the amount of LED current drive
(I ). For conditions where I is close to the switching
F
F
threshold (I ), CMR also depends on the extent which
TH
L
I
and I balance each other. In other words, any condi-
LP
LN
should be connected to either V or logic-level high for
CC
tion where common-mode transients cause a momen-
best common-mode performance with the output low
tary decrease in I will cause common-mode failure for
F
(CMR ). This failure mechanism is only present in single-
L
transients which are fast enough.
channel parts which have the enable function.
HCPL-260L
*
1
8
7
V
V
CC
CC+
0.01 µF
220 Ω
220 Ω
350 Ω
2
3
4
6
5
V
O
74LS04
OR ANY TOTEM-POLE
OUTPUT LOGIC GATE
GND
SHIELD
*
GND1
GND2
* HIGHER CMR MAY BE OBTAINABLE BY CONNECTING PINS 1, 4 TO INPUT GROUND (GND1).
Figure 13. Recommended drive circuit for High-CMR.
1
2
8
7
V
V
+
CC
O
1/2 R
1/2 R
0.01 µF
LED
LED
350 Ω
I
LP
C
I
LA
LN
3
4
6
5
15 pF
C
LC
GND
SHIELD
+
–
V
CM
Figure 14. AC equivalent circuit.
18
V
Likewise for common-mode transients which occur
when the LED is off (i.e. CMR , since the output is“high”),
CC
H
HCPL-260L
LED
if an imbalance between I and I results in a transient
LP
LN
1
2
420 Ω
I equal to or greater than the switching threshold of the
(MAX)
F
optocoupler, the transient“signal”may cause the output
2N3906
(ANY PNP)
to spike below 2 V (which constitutes a CMR failure).
H
74L504
(ANY
TTL/CMOS
GATE)
By using the recommended circuit in Figure 13, good
3
4
CMR can be achieved. The balanced I -setting resistors
LED
help equalize I and I to reduce the amount by which
LP
LN
I
is modulated from transient coupling through C
LED
LA
and C .
LC
CMR with Other Drive Circuits
CMR performance with drive circuits other than that
shown in Figure 13 may be enhanced by following these
guidelines:
Figure 15. TTL interface circuit.
V
CC
HCPL-260L
1. Use of drive circuits where current is shunted from the
LED in the LED “off” state (as shown in Figures 15 and
1
2
R
16). This is beneficial for good CMR .
H
2. Use of I > 3.5 mA. This is good for high CMR .
FH
L
74HC00
(OR ANY
LED
Figure 15 shows a circuit which can be used with any
totem-pole-output TTL/LSTTL/HCMOS logic gate. The
buffer PNP transistor allows the circuit to be used with
logic devices which have low current-sinking capability.
It also helps maintain the driving-gate power-supply cur-
rent at a constant level to minimize ground shifting for
other devices connected to the input-supply ground.
OPEN-COLLECTOR/
OPEN-DRAIN
3
4
LOGIC GATE)
Figure 16. TTL open-collector/open drain gate drive circuit.
When using an open-collector TTL or open-drain CMOS
logic gate, the circuit in Figure 16 may be used. When
using a CMOS gate to drive the optocoupler, the circuit
shown in Figure 17 may be used. The diode in parallel
V
CC
HCPL-260L
1N4148
1
2
with the R
LED.
speeds the turn-off of the optocoupler
LED
220 Ω
74HC04
(OR ANY
LED
TOTEM-POLE
OUTPUT LOGIC
GATE)
3
4
Figure 17. CMOS gate drive circuit.
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved. Obsoletes AV01-0581EN
AV02-0616EN - May 13, 2013
相关型号:
©2020 ICPDF网 联系我们和版权申明