AT91SAM7S64B-AU 概述
AT91 ARM Thumb-based Microcontrollers AT91 ARM的Thumb-基于微控制器 微控制器 微控制器
AT91SAM7S64B-AU 规格参数
是否Rohs认证: | 符合 | 生命周期: | Obsolete |
零件包装代码: | QFP | 包装说明: | GREEN, MS-026, LQFP-64 |
针数: | 64 | Reach Compliance Code: | unknown |
ECCN代码: | 3A001.A.3 | HTS代码: | 8542.31.00.01 |
风险等级: | 5.74 | Samacsys Confidence: | 3 |
Samacsys Status: | Released | Samacsys PartID: | 579570 |
Samacsys Pin Count: | 64 | Samacsys Part Category: | Integrated Circuit |
Samacsys Package Category: | Quad Flat Packages | Samacsys Footprint Name: | 64-Lead LQFP |
Samacsys Released Date: | 2017-01-11 11:27:27 | Is Samacsys: | N |
具有ADC: | YES | 其他特性: | ALSO REQUIRES 3.3V SUPPLY |
地址总线宽度: | 位大小: | 32 | |
CPU系列: | ARM7 | 最大时钟频率: | 50 MHz |
DAC 通道: | NO | DMA 通道: | YES |
外部数据总线宽度: | JESD-30 代码: | S-PQFP-G64 | |
长度: | 10 mm | 湿度敏感等级: | 3 |
I/O 线路数量: | 32 | 端子数量: | 64 |
最高工作温度: | 85 °C | 最低工作温度: | -40 °C |
PWM 通道: | YES | 封装主体材料: | PLASTIC/EPOXY |
封装代码: | LFQFP | 封装等效代码: | QFP64,.47SQ,20 |
封装形状: | SQUARE | 封装形式: | FLATPACK, LOW PROFILE, FINE PITCH |
电源: | 1.8,3.3 V | 认证状态: | Not Qualified |
RAM(字节): | 16384 | ROM(单词): | 16384 |
ROM可编程性: | FLASH | 座面最大高度: | 1.6 mm |
速度: | 55 MHz | 子类别: | Microcontrollers |
最大供电电压: | 1.95 V | 最小供电电压: | 1.65 V |
标称供电电压: | 1.8 V | 表面贴装: | YES |
技术: | CMOS | 温度等级: | INDUSTRIAL |
端子形式: | GULL WING | 端子节距: | 0.5 mm |
端子位置: | QUAD | 宽度: | 10 mm |
uPs/uCs/外围集成电路类型: | MICROCONTROLLER, RISC | Base Number Matches: | 1 |
AT91SAM7S64B-AU 数据手册
通过下载AT91SAM7S64B-AU数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Features
• Incorporates the ARM7TDMI® ARM® Thumb® Processor
– High-performance 32-bit RISC Architecture
– High-density 16-bit Instruction Set
– Leader in MIPS/Watt
– EmbeddedICE™ In-circuit Emulation, Debug Communication Channel Support
• Internal High-speed Flash
– 512 Kbytes (AT91SAM7S512) Organized in Two Contiguous Banks of 1024 Pages
of 256 Bytes (Dual Plane)
– 256 Kbytes (AT91SAM7S256) Organized in 1024 Pages of 256 Bytes (Single Plane)
– 128 Kbytes (AT91SAM7S128) Organized in 512 Pages of 256 Bytes (Single Plane)
– 64 Kbytes (AT91SAM7S64) Organized in 512 Pages of 128 Bytes (Single Plane)
– 32 Kbytes (AT91SAM7S321/32) Organized in 256 Pages of 128 Bytes (Single Plane)
– 16 Kbytes (AT91SAM7S161/16 Organized in 256 Pages of 64 Bytes (Single Plane)
– Single Cycle Access at Up to 30 MHz in Worst Case Conditions
– Prefetch Buffer Optimizing Thumb Instruction Execution at Maximum Speed
– Page Programming Time: 6 ms, Including Page Auto-erase, Full Erase Time: 15 ms
– 10,000 Write Cycles, 10-year Data Retention Capability, Sector Lock Capabilities,
Flash Security Bit
AT91 ARM
Thumb-based
Microcontrollers
AT91SAM7S512
AT91SAM7S256
AT91SAM7S128
AT91SAM7S64
AT91SAM7S321
AT91SAM7S32
AT91SAM7S161
AT91SAM7S16
Summary
– Fast Flash Programming Interface for High Volume Production
• Internal High-speed SRAM, Single-cycle Access at Maximum Speed
– 64 Kbytes (AT91SAM7S512/256)
– 32 Kbytes (AT91SAM7S128)
– 16 Kbytes (AT91SAM7S64)
– 8 Kbytes (AT91SAM7S321/32)
– 4 Kbytes (AT91SAM7S161/16)
• Memory Controller (MC)
– Embedded Flash Controller, Abort Status and Misalignment Detection
• Reset Controller (RSTC)
– Based on Power-on Reset and Low-power Factory-calibrated Brown-out Detector
– Provides External Reset Signal Shaping and Reset Source Status
• Clock Generator (CKGR)
– Low-power RC Oscillator, 3 to 20 MHz On-chip Oscillator and one PLL
• Power Management Controller (PMC)
– Software Power Optimization Capabilities, Including Slow Clock Mode (Down to
500 Hz) and Idle Mode
– Three Programmable External Clock Signals
• Advanced Interrupt Controller (AIC)
– Individually Maskable, Eight-level Priority, Vectored Interrupt Sources
– Two (AT91SAM7S512/256/128/64/321/161) or One (AT91SAM7S32/16) External
Interrupt Source(s) and One Fast Interrupt Source, Spurious Interrupt Protected
• Debug Unit (DBGU)
– 2-wire UART and Support for Debug Communication Channel interrupt,
Programmable ICE Access Prevention
– Mode for General Purpose 2-wire UART Serial Communication
• Periodic Interval Timer (PIT)
NOTE: This is a summary document.
The complete document is available on
the Atmel website at www.atmel.com.
– 20-bit Programmable Counter plus 12-bit Interval Counter
• Windowed Watchdog (WDT)
– 12-bit key-protected Programmable Counter
– Provides Reset or Interrupt Signals to the System
6175GS–ATARM–24-Dec-08
– Counter May Be Stopped While the Processor is in Debug State or in Idle Mode
• Real-time Timer (RTT)
– 32-bit Free-running Counter with Alarm
– Runs Off the Internal RC Oscillator
• One Parallel Input/Output Controller (PIOA)
– Thirty-two (AT91SAM7S512/256/128/64/321/161) or twenty-one (AT91SAM7S32/16) Programmable I/O Lines Multiplexed
with up to Two Peripheral I/Os
– Input Change Interrupt Capability on Each I/O Line
– Individually Programmable Open-drain, Pull-up resistor and Synchronous Output
• Eleven (AT91SAM7S512/256/128/64/321/161) or Nine (AT91SAM7S32/16) Peripheral DMA Controller (PDC) Channels
• One USB 2.0 Full Speed (12 Mbits per Second) Device Port (Except for the AT91SAM7S32/16).
– On-chip Transceiver, 328-byte Configurable Integrated FIFOs
• One Synchronous Serial Controller (SSC)
– Independent Clock and Frame Sync Signals for Each Receiver and Transmitter
– I²S Analog Interface Support, Time Division Multiplex Support
– High-speed Continuous Data Stream Capabilities with 32-bit Data Transfer
• Two (AT91SAM7S512/256/128/64/321/161) or One (AT91SAM7S32/16) Universal Synchronous/Asynchronous Receiver
Transmitters (USART)
– Individual Baud Rate Generator, IrDA® Infrared Modulation/Demodulation
– Support for ISO7816 T0/T1 Smart Card, Hardware Handshaking, RS485 Support
– Full Modem Line Support on USART1 (AT91SAM7S512/256/128/64/321/161)
• One Master/Slave Serial Peripheral Interface (SPI)
– 8- to 16-bit Programmable Data Length, Four External Peripheral Chip Selects
• One Three-channel 16-bit Timer/Counter (TC)
– Three External Clock Input and Two Multi-purpose I/O Pins per Channel (AT91SAM7S512/256/128/64/321/161)
– One External Clock Input and Two Multi-purpose I/O Pins for the first Two Channels Only (AT91SAM7S32/16)
– Double PWM Generation, Capture/Waveform Mode, Up/Down Capability
• One Four-channel 16-bit PWM Controller (PWMC)
• One Two-wire Interface (TWI)
– Master Mode Support Only, All Two-wire Atmel EEPROMs and I2C Compatible Devices Supported
(AT91SAM7S512/256/128/64/321/32)
– Master, Multi-Master and Slave Mode Support, All Two-wire Atmel EEPROMs and I2C Compatible Devices Supported
(AT91SAM7S161/16)
• One 8-channel 10-bit Analog-to-Digital Converter, Four Channels Multiplexed with Digital I/Os
• SAM-BA™ Boot Assistant
– Default Boot program
– Interface with SAM-BA Graphic User Interface
• IEEE® 1149.1 JTAG Boundary Scan on All Digital Pins
• 5V-tolerant I/Os, including Four High-current Drive I/O lines, Up to 16 mA Each (AT91SAM7S161/16 I/Os Not 5V-tolerant)
• Power Supplies
– Embedded 1.8V Regulator, Drawing up to 100 mA for the Core and External Components
– 3.3V or 1.8V VDDIO I/O Lines Power Supply, Independent 3.3V VDDFLASH Flash Power Supply
– 1.8V VDDCORE Core Power Supply with Brown-out Detector
• Fully Static Operation: Up to 55 MHz at 1.65V and 85⋅ C Worst Case Conditions
• Available in 64-lead LQFP Green or 64-pad QFN Green Package (AT91SAM7S512/256/128/64/321/161) and 48-lead LQFP Green
or 48-pad QFN Green Package (AT91SAM7S32/16)
2
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
1. Description
Atmel’s AT91SAM7S is a series of low pincount Flash microcontrollers based on the 32-bit ARM
RISC processor. It features a high-speed Flash and an SRAM, a large set of peripherals, includ-
ing a USB 2.0 device (except for the AT91SAM7S32 and AT91SAM7S16), and a complete set
of system functions minimizing the number of external components. The device is an ideal
migration path for 8-bit microcontroller users looking for additional performance and extended
memory.
The embedded Flash memory can be programmed in-system via the JTAG-ICE interface or via
a parallel interface on a production programmer prior to mounting. Built-in lock bits and a secu-
rity bit protect the firmware from accidental overwrite and preserves its confidentiality.
The AT91SAM7S Series system controller includes a reset controller capable of managing the
power-on sequence of the microcontroller and the complete system. Correct device operation
can be monitored by a built-in brownout detector and a watchdog running off an integrated RC
oscillator.
The AT91SAM7S Series are general-purpose microcontrollers. Their integrated USB Device
port makes them ideal devices for peripheral applications requiring connectivity to a PC or cellu-
lar phone. Their aggressive price point and high level of integration pushes their scope of use far
into the cost-sensitive, high-volume consumer market.
1.1
Configuration Summary of the AT91SAM7S512, AT91SAM7S256, AT91SAM7S128,
AT91SAM7S64, AT91SAM7S321, AT91SAM7S32, AT91SAM7S161 and AT91SAM7S16
The AT91SAM7S512, AT91SAM7S256, AT91SAM7S128, AT91SAM7S64, AT91SAM7S321,
AT91SAM7S32, AT91SAM7S161 and AT91SAM7S16 differ in memory size, peripheral set and
package. Table 1-1 summarizes the configuration of the six devices.
Except for the AT91SAM7S32/16, all other AT91SAM7S devices are package and pinout
compatible.
Table 1-1.
Configuration Summary
USB
External
Flash
Organization SRAM
Device
Port
Interrupt PDC
TC
I/O 5V
I/O
Device
Flash
TWI
USART Source
Channels Channels Tolerant Lines
Package
LQFP/
QFN 64
AT91SAM7S512 512 Kbytes Master
AT91SAM7S256 256 Kbytes Master
AT91SAM7S128 128 Kbytes Master
AT91SAM7S64 64 Kbytes Master
AT91SAM7S321 32 Kbytes Master
AT91SAM7S32 32 Kbytes Master
dual plane
64 Kbytes 1
2(1) (2)
2(1) (2)
2(1) (2)
2(2)
2
2
2
2
2
1
2
1
11
11
11
11
11
9
3
Yes
Yes
Yes
Yes
Yes
Yes
No
32
32
32
32
32
21
32
21
LQFP/
QFN 64
single plane 64 Kbytes 1
single plane 32 Kbytes 1
single plane 16 Kbytes 1
3
LQFP/
QFN 64
3
LQFP/
QFN 64
3
LQFP/
QFN 64
single plane 8 Kbytes
single plane 8 Kbytes
single plane 4 Kbytes
single plane 4 Kbytes
1
2(2)
3
not
present
LQFP/
QFN 48
1
3(3)
3
Master/
AT91SAM7S161 16 Kbytes
Slave
1
2(2)
11
9
LQFP
Master/
AT91SAM7S16 16 Kbytes
Slave
not
present
LQFP/
QFN 48
1
3(3)
No
Notes: 1. Fractional Baud Rate.
2. Full modem line support on USART1.
3. Only two TC channels are accessible through the PIO.
3
6175GS–ATARM–24-Dec-08
2. Block Diagram
Figure 2-1. AT91SAM7S512/256/128/64/321/161 Block Diagram
TDI
TDO
TMS
TCK
ICE
ARM7TDMI
Processor
JTAG
SCAN
JTAGSEL
1.8 V
Voltage
VDDIN
GND
System Controller
AIC
Regulator
VDDOUT
TST
FIQ
VDDCORE
VDDIO
IRQ0-IRQ1
Memory Controller
SRAM
Embedded
Address
Decoder
64/32/16/8/4 Kbytes
Flash
PCK0-PCK2
PLLRC
Controller
PLL
PMC
Abort
Status
Misalignment
Detection
XIN
XOUT
OSC
VDDFLASH
ERASE
Flash
512/256/
128/64/32/16 Kbytes
RCOSC
VDDCORE
BOD
POR
Peripheral Bridge
Reset
Controller
VDDCORE
NRST
ROM
Peripheral Data
Controller
PGMRDY
PGMNVALID
PGMNOE
PGMCK
PGMM0-PGMM3
PGMD0-PGMD15
PGMNCMD
Fast Flash
Programming
Interface
11 Channels
PIT
WDT
RTT
APB
PGMEN0-PGMEN2
SAM-BA
PDC
PDC
DRXD
DTXD
DBGU
FIFO
DDM
DDP
USB Device
PIOA
PWM0
PWM1
PWM2
PWM3
TF
TK
TD
RD
RK
RF
TCLK0
TCLK1
TCLK2
TIOA0
TIOB0
TIOA1
TIOB1
RXD0
TXD0
SCK0
RTS0
CTS0
RXD1
TXD1
SCK1
RTS1
CTS1
DCD1
DSR1
DTR1
RI1
NPCS0
NPCS1
NPCS2
NPCS3
MISO
MOSI
SPCK
PDC
PWMC
USART0
PDC
PDC
PDC
SSC
PDC
USART1
Timer Counter
PDC
PDC
TC0
TC1
TC2
TWI
TIOA2
TIOB2
SPI
TWD
TWCK
PDC
PDC
ADTRG
AD0
AD1
AD2
AD3
ADC
AD4
AD5
AD6
AD7
ADVREF
4
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Figure 2-2. AT91SAM7S32/16 Block Diagram
TDI
TDO
TMS
ICE
ARM7TDMI
Processor
JTAG
SCAN
TCK
JTAGSEL
1.8 V
Voltage
Regulator
VDDIN
GND
System Controller
TST
VDDOUT
FIQ
VDDCORE
VDDIO
AIC
IRQ0
Memory Controller
SRAM
8/4 Kbytes
Embedded
Flash
Controller
Address
Decoder
PCK0-PCK2
PLLRC
PLL
PMC
Abort
Status
Misalignment
Detection
XIN
OSC
XOUT
VDDFLASH
ERASE
Flash
32/16 Kbytes
RCOSC
VDDCORE
BOD
Peripheral Bridge
Reset
Controller
POR
VDDCORE
NRST
Peripheral DMA
Controller
ROM
PGMRDY
PGMNVALID
PGMNOE
9 Channels
PIT
WDT
RTT
Fast Flash
Programming
Interface
PGMCK
APB
PGMM0-PGMM3
PGMD0-PGMD7
PGMNCMD
PGMEN0-PGMEN2
SAM-BA
PDC
PDC
DRXD
DTXD
DBGU
PIOA
PWM0
PWM1
PWM2
PWM3
TF
TK
TD
RD
RK
PWMC
SSC
RXD0
TXD0
SCK0
RTS0
CTS0
PDC
PDC
PDC
USART0
PDC
PDC
NPCS0
NPCS1
NPCS2
NPCS3
MISO
RF
TCLK0
SPI
Timer Counter
MOSI
SPCK
TIOA0
TIOB0
PDC
PDC
TC0
TC1
TC2
TWI
ADTRG
AD0
AD1
AD2
AD3
TIOA1
TIOB1
ADC
AD4
AD5
AD6
AD7
TWD
TWCK
ADVREF
5
6175GS–ATARM–24-Dec-08
3. Signal Description
Table 3-1.
Signal Description List
Active
Level
Signal Name
Function
Type
Comments
Power
Voltage and ADC Regulator Power Supply
Input
VDDIN
Power
3.0 to 3.6V
VDDOUT
VDDFLASH
VDDIO
Voltage Regulator Output
Flash Power Supply
I/O Lines Power Supply
Core Power Supply
PLL
Power
Power
Power
Power
Power
Ground
1.85V nominal
3.0V to 3.6V
3.0V to 3.6V or 1.65V to 1.95V
1.65V to 1.95V
VDDCORE
VDDPLL
GND
1.65V to 1.95V
Ground
Clocks, Oscillators and PLLs
XIN
Main Oscillator Input
Main Oscillator Output
PLL Filter
Input
Output
XOUT
PLLRC
PCK0 - PCK2
Input
Programmable Clock Output
Output
ICE and JTAG
Input
TCK
Test Clock
No pull-up resistor
No pull-up resistor
TDI
Test Data In
Input
TDO
Test Data Out
Test Mode Select
JTAG Selection
Output
TMS
Input
No pull-up resistor
Pull-down resistor(1)
JTAGSEL
Input
Flash Memory
Flash and NVM Configuration Bits Erase
Command
ERASE
Input
High
Pull-down resistor(1)
Reset/Test
NRST
TST
Microcontroller Reset
Test Mode Select
I/O
Low
Open-drain with pull-Up resistor
Pull-down resistor(1)
Input
High
Debug Unit
DRXD
DTXD
Debug Receive Data
Debug Transmit Data
Input
Output
AIC
PIO
IRQ0 - IRQ1
FIQ
External Interrupt Inputs
Fast Interrupt Input
Input
Input
IRQ1 not present on AT91SAM7S32/16
Pulled-up input at reset
PA0 - PA31
Parallel IO Controller A
I/O
PA0 - PA20 only on AT91SAM7S32/16
6
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Table 3-1.
Signal Description List (Continued)
Active
Signal Name
Function
Type
USB Device Port
Analog
Analog
USART
I/O
Level
Comments
DDM
DDP
USB Device Port Data -
USB Device Port Data +
not present on AT91SAM7S32/16
not present on AT91SAM7S32/16
SCK0 - SCK1
TXD0 - TXD1
RXD0 - RXD1
RTS0 - RTS1
CTS0 - CTS1
DCD1
Serial Clock
SCK1 not present on AT91SAM7S32/16
TXD1 not present on AT91SAM7S32/16
RXD1 not present on AT91SAM7S32/16
RTS1 not present on AT91SAM7S32/16
CTS1 not present on AT91SAM7S32/16
not present on AT91SAM7S32/16
Transmit Data
I/O
Receive Data
Input
Request To Send
Clear To Send
Output
Input
Data Carrier Detect
Data Terminal Ready
Data Set Ready
Ring Indicator
Input
DTR1
Output
Input
not present on AT91SAM7S32/16
DSR1
not present on AT91SAM7S32/16
RI1
Input
not present on AT91SAM7S32/16
Synchronous Serial Controller
TD
RD
TK
RK
TF
RF
Transmit Data
Output
Receive Data
Input
Transmit Clock
I/O
Receive Clock
I/O
Transmit Frame Sync
Receive Frame Sync
I/O
I/O
Timer/Counter
TCLK1 and TCLK2 not present on
AT91SAM7S32/16
TCLK0 - TCLK2
External Clock Inputs
Input
TIOA0 - TIOA2
TIOB0 - TIOB2
I/O Line A
I/O Line B
I/O
TIOA2 not present on AT91SAM7S32/16
TIOB2 not present on AT91SAM7S32/16
I/O
PWM Controller
PWM0 - PWM3
PWM Channels
Output
SPI
I/O
I/O
I/O
I/O
MISO
Master In Slave Out
Master Out Slave In
SPI Serial Clock
MOSI
SPCK
NPCS0
NPCS1-NPCS3
SPI Peripheral Chip Select 0
Low
Low
SPI Peripheral Chip Select 1 to 3
Output
7
6175GS–ATARM–24-Dec-08
Table 3-1.
Signal Description List (Continued)
Active
Level
Signal Name
Function
Type
Comments
Two-Wire Interface
TWD
Two-wire Serial Data
Two-wire Serial Clock
I/O
I/O
TWCK
Analog-to-Digital Converter
AD0-AD3
AD4-AD7
ADTRG
Analog Inputs
Analog Inputs
ADC Trigger
Analog
Analog
Input
Digital pulled-up inputs at reset
Analog Inputs
ADVREF
ADC Reference
Analog
Fast Flash Programming Interface
PGMEN0-PGMEN2 Programming Enabling
Input
Input
PGMM0-PGMM3
PGMD0-PGMD15
Programming Mode
Programming Data
PGMD0-PGMD7 only on
AT91SAM7S32/16
I/O
PGMRDY
PGMNVALID
PGMNOE
PGMCK
Programming Ready
Data Direction
Output
Output
Input
High
Low
Low
Programming Read
Programming Clock
Programming Command
Input
PGMNCMD
Input
Low
Note:
1. Refer to Section 6. “I/O Lines Considerations” on page 14.
8
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
4. Package and Pinout
The AT91SAM7S512/256/128/64/321 are available in a 64-lead LQFP or 64-pad QFN package.
The AT91SAM7S161 is available in a 64-Lead LQFP package.
The AT91SAM7S32/16 are available in a 48-lead LQFP or 48-pad QFN package.
4.1
64-lead LQFP and 64-pad QFN Package Outlines
Figure 4-1 and Figure 4-2 show the orientation of the 64-lead LQFP and the 64-pad QFN pack-
age. A detailed mechanical description is given in the section Mechanical Characteristics of the
full datasheet.
Figure 4-1. 64-lead LQFP Package (Top View)
48
33
49
32
17
64
1
16
Figure 4-2. 64-pad QFN Package (Top View)
48
33
49
32
64
17
1
16
9
6175GS–ATARM–24-Dec-08
4.2
64-lead LQFP and 64-pad QFN Pinout
Table 4-1.
AT91SAM7S512/256/128/64/321/161 Pinout(1)
1
2
3
4
5
6
7
8
ADVREF
GND
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
GND
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
TDI
PA6/PGMNOE
PA5/PGMRDY
PA4/PGMNCMD
PA27/PGMD15
PA28
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
TDO
JTAGSEL
TMS
VDDIO
AD4
PA16/PGMD4
PA15/PGMD3
PA14/PGMD2
PA13/PGMD1
PA24/PGMD12
VDDCORE
AD5
PA31
AD6
TCK
AD7
VDDCORE
ERASE
DDM
VDDIN
VDDOUT
NRST
TST
9
PA17/PGMD5/AD0
PA18/PGMD6/AD1
PA21/PGMD9
PA25/PGMD13
PA26/PGMD14
PA12/PGMD0
PA11/PGMM3
PA10/PGMM2
PA9/PGMM1
PA8/PGMM0
PA7/PGMNVALID
PA29
DDP
10
11
12
13
14
15
PA30
VDDIO
VDDFLASH
GND
PA3
VDDCORE
PA2/PGMEN2
VDDIO
PA19/PGMD7/AD2
PA22/PGMD10
PA23/PGMD11
PA20/PGMD8/AD3
XOUT
GND
XIN/PGMCK
PLLRC
VDDPLL
PA1/PGMEN1
PA0/PGMEN0
16
Note:
1. The bottom pad of the QFN package must be connected to ground.
10
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
4.3
48-lead LQFP and 48-pad QFN Package Outlines
Figure 4-3 and Figure 4-4 show the orientation of the 48-lead LQFP and the 48-pad QFN pack-
age. A detailed mechanical description is given in the section Mechanical Characteristics of the
full datasheet.
Figure 4-3. 48-lead LQFP Package (Top View)
36
25
37
48
24
13
1
12
Figure 4-4. 48-pad QFN Package (Top View)
36
25
37
24
48
13
1
12
4.4
48-lead LQFP and 48-pad QFN Pinout
Table 4-2.
AT91SAM7S32/16 Pinout(1)
ADVREF 13
GND 14
1
2
3
4
5
6
7
8
VDDIO
25
26
27
28
29
30
31
32
33
34
35
36
TDI
37
38
39
40
41
42
43
44
45
46
47
48
TDO
JTAGSEL
TMS
PA16/PGMD4
PA15/PGMD3
PA14/PGMD2
PA13/PGMD1
VDDCORE
PA6/PGMNOE
PA5/PGMRDY
PA4/PGMNCMD
NRST
AD4
AD5
15
16
17
18
19
20
21
22
23
24
TCK
AD6
VDDCORE
ERASE
VDDFLASH
GND
AD7
TST
VDDIN
VDDOUT
PA12/PGMD0
PA11/PGMM3
PA10/PGMM2
PA9/PGMM1
PA8/PGMM0
PA7/PGMNVALID
PA3
PA2/PGMEN2
VDDIO
9
10
PA17/PGMD5/AD0
PA18/PGMD6/AD1
PA19/PGMD7/AD2
PA20/AD3
XOUT
GND
XIN/PGMCK
PLLRC
11
PA1/PGMEN1
PA0/PGMEN0
12
VDDPLL
Note:
1. The bottom pad of the QFN package must be connected to ground.
11
6175GS–ATARM–24-Dec-08
5. Power Considerations
5.1
Power Supplies
The AT91SAM7S Series has six types of power supply pins and integrates a voltage regulator,
allowing the device to be supplied with only one voltage. The six power supply pin types are:
• VDDIN pin. It powers the voltage regulator and the ADC; voltage ranges from 3.0V to 3.6V,
3.3V nominal.
• VDDOUT pin. It is the output of the 1.8V voltage regulator.
• VDDIO pin. It powers the I/O lines and the USB transceivers; dual voltage range is
supported. Ranges from 3.0V to 3.6V, 3.3V nominal or from 1.65V to 1.95V, 1.8V nominal.
Note that supplying less than 3.0V to VDDIO prevents any use of the USB transceivers.
• VDDFLASH pin. It powers a part of the Flash and is required for the Flash to operate
correctly; voltage ranges from 3.0V to 3.6V, 3.3V nominal.
• VDDCORE pins. They power the logic of the device; voltage ranges from 1.65V to 1.95V,
1.8V typical. It can be connected to the VDDOUT pin with decoupling capacitor. VDDCORE
is required for the device, including its embedded Flash, to operate correctly.
During startup, core supply voltage (VDDCORE) slope must be superior or equal to 6V/ms.
• VDDPLL pin. It powers the oscillator and the PLL. It can be connected directly to the
VDDOUT pin.
No separate ground pins are provided for the different power supplies. Only GND pins are pro-
vided and should be connected as shortly as possible to the system ground plane.
In order to decrease current consumption, if the voltage regulator and the ADC are not used,
VDDIN, ADVREF, AD4, AD5, AD6 and AD7 should be connected to GND. In this case VDDOUT
should be left unconnected.
5.2
5.3
Power Consumption
The AT91SAM7S Series has a static current of less than 60 µA on VDDCORE at 25°C, including
the RC oscillator, the voltage regulator and the power-on reset. When the brown-out detector is
activated, 20 µA static current is added.
The dynamic power consumption on VDDCORE is less than 50 mA at full speed when running
out of the Flash. Under the same conditions, the power consumption on VDDFLASH does not
exceed 10 mA.
Voltage Regulator
The AT91SAM7S Series embeds a voltage regulator that is managed by the System Controller.
In Normal Mode, the voltage regulator consumes less than 100 µA static current and draws 100
mA of output current.
The voltage regulator also has a Low-power Mode. In this mode, it consumes less than 25 µA
static current and draws 1 mA of output current.
Adequate output supply decoupling is mandatory for VDDOUT to reduce ripple and avoid oscil-
lations. The best way to achieve this is to use two capacitors in parallel: one external 470 pF (or
1 nF) NPO capacitor must be connected between VDDOUT and GND as close to the chip as
possible. One external 2.2 µF (or 3.3 µF) X7R capacitor must be connected between VDDOUT
and GND.
12
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Adequate input supply decoupling is mandatory for VDDIN in order to improve startup stability
and reduce source voltage drop. The input decoupling capacitor should be placed close to the
chip. For example, two capacitors can be used in parallel: 100 nF NPO and 4.7 µF X7R.
5.4
Typical Powering Schematics
The AT91SAM7S Series supports a 3.3V single supply mode. The internal regulator is con-
nected to the 3.3V source and its output feeds VDDCORE and the VDDPLL. Figure 5-1 shows
the power schematics to be used for USB bus-powered systems.
Figure 5-1.
3.3V System Single Power Supply Schematic
VDDFLASH
Power Source
VDDIO
ranges
from 4.5V (USB)
to 18V
DC/DC Converter
VDDIN
Voltage
Regulator
3.3V
VDDOUT
VDDCORE
VDDPLL
13
6175GS–ATARM–24-Dec-08
6. I/O Lines Considerations
6.1
JTAG Port Pins
TMS, TDI and TCK are schmitt trigger inputs. TMS and TCK are 5-V tolerant, TDI is not. TMS,
TDI and TCK do not integrate a pull-up resistor.
TDO is an output, driven at up to VDDIO, and has no pull-up resistor.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level. The
JTAGSEL pin integrates a permanent pull-down resistor of about 15 kΩto GND, so that it can be
left unconnected for normal operations.
6.2
Test Pin
The TST pin is used for manufacturing test, fast programming mode or SAM-BA Boot Recovery
of the AT91SAM7S Series when asserted high. The TST pin integrates a permanent pull-down
resistor of about 15 kΩ to GND, so that it can be left unconnected for normal operations.
To enter fast programming mode, the TST pin and the PA0 and PA1 pins should be tied high
and PA2 tied to low.
To enter SAM-BA Boot Recovery, the TST pin and the PA0, PA1 and PA2 pins should be tied
high fo at least 10 seconds.
Driving the TST pin at a high level while PA0 or PA1 is driven at 0 leads to unpredictable results.
6.3
Reset Pin
The NRST pin is bidirectional with an open drain output buffer. It is handled by the on-chip reset
controller and can be driven low to provide a reset signal to the external components or asserted
low externally to reset the microcontroller. There is no constraint on the length of the reset pulse,
and the reset controller can guarantee a minimum pulse length. This allows connection of a sim-
ple push-button on the pin NRST as system user reset, and the use of the signal NRST to reset
all the components of the system.
The NRST pin integrates a permanent pull-up resistor to VDDIO.
6.4
6.5
ERASE Pin
The ERASE pin is used to re-initialize the Flash content and some of its NVM bits. It integrates a
permanent pull-down resistor of about 15 kΩ to GND, so that it can be left unconnected for nor-
mal operations.
PIO Controller A Lines
• All the I/O lines PA0 to PA31on AT91SAM7S512/256/128/64/321 (PA0 to PA20 on
AT91SAM7S32) are 5V-tolerant and all integrate a programmable pull-up resistor.
• All the I/O lines PA0 to PA31 on AT91SAM7S161 (PA0 to PA20 on AT91SAM7S16) are not
5V-tolerant and all integrate a programmable pull-up resistor.
Programming of this pull-up resistor is performed independently for each I/O line through the
PIO controllers.
5V-tolerant means that the I/O lines can drive voltage level according to VDDIO, but can be
driven with a voltage of up to 5.5V. However, driving an I/O line with a voltage over VDDIO while
the programmable pull-up resistor is enabled will create a current path through the pull-up resis-
14
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
tor from the I/O line to VDDIO. Care should be taken, in particular at reset, as all the I/O lines
default to input with the pull-up resistor enabled at reset.
6.6
I/O Line Drive Levels
The PIO lines PA0 to PA3 are high-drive current capable. Each of these I/O lines can drive up to
16 mA permanently.
The remaining I/O lines can draw only 8 mA.
However, the total current drawn by all the I/O lines cannot exceed 150 mA (100 mA for
AT91SAM7S32/16).
15
6175GS–ATARM–24-Dec-08
7. Processor and Architecture
7.1
7.2
7.3
ARM7TDMI Processor
• RISC processor based on ARMv4T Von Neumann architecture
– Runs at up to 55 MHz, providing 0.9 MIPS/MHz
• Two instruction sets
– ARM® high-performance 32-bit instruction set
– Thumb® high code density 16-bit instruction set
• Three-stage pipeline architecture
– Instruction Fetch (F)
– Instruction Decode (D)
– Execute (E)
Debug and Test Features
• Integrated EmbeddedICE™ (embedded in-circuit emulator)
– Two watchpoint units
– Test access port accessible through a JTAG protocol
– Debug communication channel
• Debug Unit
– Two-pin UART
– Debug communication channel interrupt handling
– Chip ID Register
• IEEE1149.1 JTAG Boundary-scan on all digital pins
Memory Controller
• Bus Arbiter
– Handles requests from the ARM7TDMI and the Peripheral DMA Controller
• Address decoder provides selection signals for
– Three internal 1 Mbyte memory areas
– One 256 Mbyte embedded peripheral area
• Abort Status Registers
– Source, Type and all parameters of the access leading to an abort are saved
– Facilitates debug by detection of bad pointers
• Misalignment Detector
– Alignment checking of all data accesses
– Abort generation in case of misalignment
• Remap Command
– Remaps the SRAM in place of the embedded non-volatile memory
– Allows handling of dynamic exception vectors
• Embedded Flash Controller
– Embedded Flash interface, up to three programmable wait states
16
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
– Prefetch buffer, buffering and anticipating the 16-bit requests, reducing the required
wait states
– Key-protected program, erase and lock/unlock sequencer
– Single command for erasing, programming and locking operations
– Interrupt generation in case of forbidden operation
7.4
Peripheral DMA Controller
• Handles data transfer between peripherals and memories
• Eleven channels: AT91SAM7S512/256/128/64/321/161
• Nine channels: AT91SAM7S32/16
– Two for each USART
– Two for the Debug Unit
– Two for the Serial Synchronous Controller
– Two for the Serial Peripheral Interface
– One for the Analog-to-digital Converter
• Low bus arbitration overhead
– One Master Clock cycle needed for a transfer from memory to peripheral
– Two Master Clock cycles needed for a transfer from peripheral to memory
• Next Pointer management for reducing interrupt latency requirements
• Peripheral DMA Controller (PDC) priority is as follows (from the highest priority to the lowest):
Receive
Receive
Receive
Receive
Receive
Receive
Transmit
Transmit
Transmit
Transmit
Transmit
DBGU
USART0
USART1
SSC
ADC
SPI
DBGU
USART0
USART1
SSC
SPI
17
6175GS–ATARM–24-Dec-08
8. Memories
8.1
8.2
8.3
AT91SAM7S512
• 512 Kbytes of Flash Memory, dual plane
– 2 contiguous banks of 1024 pages of 256 bytes
– Fast access time, 30 MHz single-cycle access in Worst Case conditions
– Page programming time: 6 ms, including page auto-erase
– Page programming without auto-erase: 3 ms
– Full chip erase time: 15 ms
– 10,000 write cycles, 10-year data retention capability
– 32 lock bits, protecting 32 sectors of 64 pages
– Protection Mode to secure contents of the Flash
• 64 Kbytes of Fast SRAM
– Single-cycle access at full speed
AT91SAM7S256
• 256 Kbytes of Flash Memory, single plane
– 1024 pages of 256 bytes
– Fast access time, 30 MHz single-cycle access in Worst Case conditions
– Page programming time: 6 ms, including page auto-erase
– Page programming without auto-erase: 3 ms
– Full chip erase time: 15 ms
– 10,000 write cycles, 10-year data retention capability
– 16 lock bits, protecting 16 sectors of 64 pages
– Protection Mode to secure contents of the Flash
• 64 Kbytes of Fast SRAM
– Single-cycle access at full speed
AT91SAM7S128
• 128 Kbytes of Flash Memory, single plane
– 512 pages of 256 bytes
– Fast access time, 30 MHz single-cycle access in Worst Case conditions
– Page programming time: 6 ms, including page auto-erase
– Page programming without auto-erase: 3 ms
– Full chip erase time: 15 ms
– 10,000 write cycles, 10-year data retention capability
– 8 lock bits, protecting 8 sectors of 64 pages
– Protection Mode to secure contents of the Flash
• 32 Kbytes of Fast SRAM
– Single-cycle access at full speed
18
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
8.4
8.5
8.6
AT91SAM7S64
• 64 Kbytes of Flash Memory, single plane
– 512 pages of 128 bytes
– Fast access time, 30 MHz single-cycle access in Worst Case conditions
– Page programming time: 6 ms, including page auto-erase
– Page programming without auto-erase: 3 ms
– Full chip erase time: 15 ms
– 10,000 write cycles, 10-year data retention capability
– 16 lock bits, protecting 16 sectors of 32 pages
– Protection Mode to secure contents of the Flash
• 16 Kbytes of Fast SRAM
– Single-cycle access at full speed
AT91SAM7S321/32
• 32 Kbytes of Flash Memory, single plane
– 256 pages of 128 bytes
– Fast access time, 30 MHz single-cycle access in Worst Case conditions
– Page programming time: 6 ms, including page auto-erase
– Page programming without auto-erase: 3 ms
– Full chip erase time: 15 ms
– 10,000 write cycles, 10-year data retention capability
– 8 lock bits, protecting 8 sectors of 32 pages
– Protection Mode to secure contents of the Flash
• 8 Kbytes of Fast SRAM
– Single-cycle access at full speed
AT91SAM7S161/16
• 16 Kbytes of Flash Memory, single plane
– 256 pages of 64 bytes
– Fast access time, 30 MHz single-cycle access in Worst Case conditions
– Page programming time: 6 ms, including page auto-erase
– Page programming without auto-erase: 3 ms
– Full chip erase time: 15 ms
– 10,000 write cycles, 10-year data retention capability
– 8 lock bits, protecting 8 sectors of 32 pages
– Protection Mode to secure contents of the Flash
• 4 Kbytes of Fast SRAM
– Single-cycle access at full speed
19
6175GS–ATARM–24-Dec-08
Figure 8-1.
AT91SAM7S512/256/128/64/321/32/161/16 Memory Mapping
Internal Memory Mapping
Note:
(1) Can be Flash or SRAM
depending on REMAP.
0x0000 0000
(1)
Flash before Remap
SRAM after Remap
1 MBytes
0x000F FFF
0x0010 0000
1 MBytes
1 MBytes
Internal Flash
Internal SRAM
0x001F FFF
0x0020 0000
0x002F FFF
0x0030 0000
Address Memory Space
Internal Memories
0x0000 0000
Reserved
253 MBytes
256 MBytes
0x0FFF FFFF
0x0FFF FFFF
0x1000 0000
System Controller Mapping
0xFFFF F000
AIC
512 Bytes/
128 registers
Peripheral Mapping
0xF000 0000
0xFFFF F1FF
0xFFFF F200
Reserved
TC0, TC1, TC2
Reserved
UDP
Undefined
(Abort)
14 x 256 MBytes
3,584 MBytes
0xFFF9 FFFF
0xFFFA 0000
512 Bytes/
128 registers
16 Kbytes
DBGU
0xFFFA 3FFF
0xFFFA 4000
0xFFFF F3FF
0xFFFF F400
0xFFFA FFFF
0xFFFB 0000
16 Kbytes
(Reserved on
AT91SAM7S32/16)
512 Bytes/
128 registers
0xFFFB 3FFF
0xFFFB 4000
PIOA
Reserved
0xFFFF F5FF
0xFFFF F600
0xFFFB 7FFF
0xFFFB 8000
TWI
16 Kbytes
0xEFFF FFFF
0xF000 0000
Reserved
0xFFFB BFFF
0xFFFB C000
0xFFFF FBFF
0xFFFF FC00
Reserved
USART0
USART1
Reserved
PWMC
0xFFFB FFFF
0xFFFC 0000
256 Bytes/
64 registers
16 Kbytes
PMC
0xFFFC 3FFF
0xFFFC 4000
16 Kbytes
(Reserved on
AT91SAM7S32/16)
0xFFFF FCFF
0xFFFF FD00
0xFFFF FD0F
Internal Peripherals 256M Bytes
16 Bytes/
4 registers
RSTC
0xFFFC 7FFF
0xFFFC 8000
Reserved
0xFFFC BFFF
0xFFFC C000
0xFFFF FFFF
16 Kbytes
0xFFFF FD20
RTT
16 Bytes/
4 registers
0xFFFC FFFF
0xFFFD 0000
0xFFFF FC2F
0xFFFF FD30
Reserved
16 Bytes/
4 registers
16 Bytes/
4 registers
PIT
0xFFFD 3FFF
0xFFFD 4000
0xFFFF FC3F
0xFFFF FD40
SSC
16 Kbytes
16 Kbytes
WDT
0xFFFD 7FFF
0xFFFD 8000
0xFFFF FD4F
ADC
Reserved
SPI
Reserved
0xFFFD BFFF
0xFFFD C000
0xFFFF FD60
4 Bytes/
1 register
VREG
0xFFFF FC6F
0xFFFF FD70
0xFFFD FFFF
0xFFFE 0000
16 Kbytes
Reserved
0xFFFF FEFF
0xFFFF FF00
0xFFFE 3FFF
0xFFFE 4000
Reserved
SYSC
256 Bytes/
64 registers
0xFFFF EFFF
0xFFFF F000
MC
0xFFFF FFFF
0xFFFF FFFF
20
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
8.7
Memory Mapping
8.7.1
Internal SRAM
• The AT91SAM7S512 embeds a high-speed 64-Kbyte SRAM bank.
• The AT91SAM7S256 embeds a high-speed 64-Kbyte SRAM bank.
• The AT91SAM7S128 embeds a high-speed 32-Kbyte SRAM bank.
• The AT91SAM7S64 embeds a high-speed 16-Kbyte SRAM bank.
• The AT91SAM7S321 embeds a high-speed 8-Kbyte SRAM bank.
• The AT91SAM7S32 embeds a high-speed 8-Kbyte SRAM bank.
• The AT91SAM7S161 embeds a high-speed 4-Kbyte SRAM bank.
• The AT91SAM7S16 embeds a high-speed 4-Kbyte SRAM bank
After reset and until the Remap Command is performed, the SRAM is only accessible at address
0x0020 0000. After Remap, the SRAM also becomes available at address 0x0.
8.7.2
8.7.3
Internal ROM
Internal Flash
The AT91SAM7S Series embeds an Internal ROM. The ROM contains the FFPI and the
SAM-BA program.
The internal ROM is not mapped by default.
• The AT91SAM7S512 features two contiguous banks (dual plane) of 256 Kbytes of Flash.
• The AT91SAM7S256 features one bank (single plane) of 256 Kbytes of Flash.
• The AT91SAM7S128 features one bank (single plane) of 128 Kbytes of Flash.
• The AT91SAM7S64 features one bank (single plane) of 64 Kbytes of Flash.
• The AT91SAM7S321/32 features one bank (single plane) of 32 Kbytes of Flash.
• The AT91SAM7S161/16 features one bank (single plane) of 16 Kbytes of Flash.
At any time, the Flash is mapped to address 0x0010 0000. It is also accessible at address 0x0
after the reset and before the Remap Command.
Figure 8-2. Internal Memory Mapping
0x0000 0000
Flash Before Remap
1 MBytes
SRAM After Remap
0x000F FFFF
0x0010 0000
Internal Flash
1 MBytes
1 MBytes
0x001F FFFF
0x0020 0000
Internal SRAM
256 MBytes
0x002F FFFF
0x0030 0000
Undefined Areas
(Abort)
253 MBytes
0x0FFF FFFF
21
6175GS–ATARM–24-Dec-08
8.8
Embedded Flash
8.8.1
Flash Overview
• The Flash of the AT91SAM7S512 is organized in two banks (dual plane) of 1024 pages of
256 bytes. The 524,288 bytes are organized in 32-bit words.
• The Flash of the AT91SAM7S256 is organized in 1024 pages (single plane) of 256 bytes. The
262,144 bytes are organized in 32-bit words.
• The Flash of the AT91SAM7S128 is organized in 512 pages (single plane) of 256 bytes. The
131,072 bytes are organized in 32-bit words.
• The Flash of the AT91SAM7S64 is organized in 512 pages (single plane) of 128 bytes. The
65,536 bytes are organized in 32-bit words.
• The Flash of the AT91SAM7S321/32 is organized in 256 pages (single plane) of 128 bytes.
The 32,768 bytes are organized in 32-bit words.
• The Flash of the AT91SAM7S161/16 is organized in 256 pages (single plane) of 64 bytes.
The 16,384 bytes are organized in 32-bit words.
• The Flash of the AT91SAM7S512/256/128 contains a 256-byte write buffer, accessible
through a 32-bit interface.
• The Flash of the AT91SAM7S64/321/32/161/16 contains a 128-byte write buffer, accessible
through a 32-bit interface.
The Flash benefits from the integration of a power reset cell and from the brownout detector.
This prevents code corruption during power supply changes, even in the worst conditions.
When Flash is not used (read or write access), it is automatically placed into standby mode.
8.8.2
Embedded Flash Controller
The Embedded Flash Controller (EFC) manages accesses performed by the masters of the sys-
tem. It enables reading the Flash and writing the write buffer. It also contains a User Interface,
mapped within the Memory Controller on the APB. The User Interface allows:
• programming of the access parameters of the Flash (number of wait states, timings, etc.)
• starting commands such as full erase, page erase, page program, NVM bit set, NVM bit
clear, etc.
• getting the end status of the last command
• getting error status
• programming interrupts on the end of the last commands or on errors
The Embedded Flash Controller also provides a dual 32-bit prefetch buffer that optimizes 16-bit
access to the Flash. This is particularly efficient when the processor is running in Thumb mode.
Two EFCs are embedded in the SAM7S512 to control each bank of 256 Kbytes. Dual plane
organization allows concurrent Read and Program. Read from one memory plane may be per-
formed even while program or erase functions are being executed in the other memory plane.
One EFC is embedded in the SAM7S256/128/64/32/321/161/16 to control the single plane
256/128/64/32/16 Kbytes.
22
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
8.8.3
Lock Regions
8.8.3.1
AT91SAM7S512
Two Embedded Flash Controllers each manage 16 lock bits to protect 16 regions of the flash
against inadvertent flash erasing or programming commands. The AT91SAM7S512 contains 32
lock regions and each lock region contains 64 pages of 256 bytes. Each lock region has a size of
16 Kbytes.
If a locked-region’s erase or program command occurs, the command is aborted and the
LOCKE bit in the MC_FSR register rises and the interrupt line rises if the LOCKE bit has been
written at 1 in the MC_FMR register.
The 16 NVM bits (or 32 NVM bits) are software programmable through the corresponding EFC
User Interface. The command “Set Lock Bit” enables the protection. The command “Clear Lock
Bit” unlocks the lock region.
Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash.
8.8.3.2
AT91SAM7S256
The Embedded Flash Controller manages 16 lock bits to protect 16 regions of the flash against
inadvertent flash erasing or programming commands. The AT91SAM7S256 contains 16 lock
regions and each lock region contains 64 pages of 256 bytes. Each lock region has a size of 16
Kbytes.
If a locked-region’s erase or program command occurs, the command is aborted and the
LOCKE bit in the MC_FSR register rises and the interrupt line rises if the LOCKE bit has been
written at 1 in the MC_FMR register.
The 16 NVM bits are software programmable through the EFC User Interface. The command
“Set Lock Bit” enables the protection. The command “Clear Lock Bit” unlocks the lock region.
Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash.
8.8.3.3
AT91SAM7S128
The Embedded Flash Controller manages 8 lock bits to protect 8 regions of the flash against
inadvertent flash erasing or programming commands. The AT91SAM7S128 contains 8 lock
regions and each lock region contains 64 pages of 256 bytes. Each lock region has a size of 16
Kbytes.
If a locked-region’s erase or program command occurs, the command is aborted and the
LOCKE bit in the MC_FSR register rises and the interrupt line rises if the LOCKE bit has been
written at 1 in the MC_FMR register.
The 8 NVM bits are software programmable through the EFC User Interface. The command “Set
Lock Bit” enables the protection. The command “Clear Lock Bit” unlocks the lock region.
Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash.
8.8.3.4
AT91SAM7S64
The Embedded Flash Controller manages 16 lock bits to protect 16 regions of the flash against
inadvertent flash erasing or programming commands. The AT91SAM7S64 contains 16 lock
regions and each lock region contains 32 pages of 128 bytes. Each lock region has a size of 4
Kbytes.
23
6175GS–ATARM–24-Dec-08
If a locked-region’s erase or program command occurs, the command is aborted and the
LOCKE bit in the MC_FSR register rises and the interrupt line rises if the LOCKE bit has been
written at 1 in the MC_FMR register.
The 16 NVM bits are software programmable through the EFC User Interface. The command
“Set Lock Bit” enables the protection. The command “Clear Lock Bit” unlocks the lock region.
Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash.
8.8.3.5
AT91SAM7S321/32
The Embedded Flash Controller manages 8 lock bits to protect 8 regions of the flash against
inadvertent flash erasing or programming commands. The AT91SAM7S321/32 contains 8 lock
regions and each lock region contains 32 pages of 128 bytes. Each lock region has a size of 4
Kbytes.
If a locked-region’s erase or program command occurs, the command is aborted and the
LOCKE bit in the MC_FSR register rises and the interrupt line rises if the LOCKE bit has been
written at 1 in the MC_FMR register.
The 8 NVM bits are software programmable through the EFC User Interface. The command “Set
Lock Bit” enables the protection. The command “Clear Lock Bit” unlocks the lock region.
Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash.
8.8.3.6
AT91SAM7S161/16
The Embedded Flash Controller manages 8 lock bits to protect 8 regions of the flash against
inadvertent flash erasing or programming commands. The AT91SAM7S161/16 contains 8 lock
regions and each lock region contains 32 pages of 64 bytes. Each lock region has a size of 2
Kbytes.
If a locked-region’s erase or program command occurs, the command is aborted and the
LOCKE bit in the MC_FSR register rises and the interrupt line rises if the LOCKE bit has been
written at 1 in the MC_FMR register.
The 8 NVM bits are software programmable through the EFC User Interface. The command “Set
Lock Bit” enables the protection. The command “Clear Lock Bit” unlocks the lock region.
Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash.
Table summarizes the configuration of the eight devices.
Flash Configuration Summary
Device
Number of Lock Bits
Number of Pages in the Lock Region
Page Size
256 bytes
256 bytes
256 bytes
128 bytes
128 bytes
64 bytes
AT91SAM7S512
AT91SAM7S256
AT91SAM7S128
AT91SAM7S64
32
16
8
64
64
64
32
32
32
16
8
AT91SAM7S321/32
AT91SAM7S161/16
8
24
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
8.8.4
Security Bit Feature
The AT91SAM7S Series features a security bit, based on a specific NVM Bit. When the security
is enabled, any access to the Flash, either through the ICE interface or through the Fast Flash
Programming Interface, is forbidden. This ensures the confidentiality of the code programmed in
the Flash.
This security bit can only be enabled, through the Command “Set Security Bit” of the EFC User
Interface. Disabling the security bit can only be achieved by asserting the ERASE pin at 1, and
after a full flash erase is performed. When the security bit is deactivated, all accesses to the
flash are permitted.
It is important to note that the assertion of the ERASE pin should always be longer than 50 ms.
As the ERASE pin integrates a permanent pull-down, it can be left unconnected during normal
operation. However, it is safer to connect it directly to GND for the final application.
8.8.5
Non-volatile Brownout Detector Control
Two general purpose NVM (GPNVM) bits are used for controlling the brownout detector (BOD),
so that even after a power loss, the brownout detector operations remain in their state.
These two GPNVM bits can be cleared or set respectively through the commands “Clear Gen-
eral-purpose NVM Bit” and “Set General-purpose NVM Bit” of the EFC User Interface.
• GPNVM Bit 0 is used as a brownout detector enable bit. Setting the GPNVM Bit 0 enables
the BOD, clearing it disables the BOD. Asserting ERASE clears the GPNVM Bit 0 and thus
disables the brownout detector by default.
• The GPNVM Bit 1 is used as a brownout reset enable signal for the reset controller. Setting
the GPNVM Bit 1 enables the brownout reset when a brownout is detected, Clearing the
GPNVM Bit 1 disables the brownout reset. Asserting ERASE disables the brownout reset by
default.
8.8.6
Calibration Bits
Eight NVM bits are used to calibrate the brownout detector and the voltage regulator. These bits
are factory configured and cannot be changed by the user. The ERASE pin has no effect on the
calibration bits.
8.9
Fast Flash Programming Interface
The Fast Flash Programming Interface allows programming the device through either a serial
JTAG interface or through a multiplexed fully-handshaked parallel port. It allows gang-program-
ming with market-standard industrial programmers.
The FFPI supports read, page program, page erase, full erase, lock, unlock and protect
commands.
The Fast Flash Programming Interface is enabled and the Fast Programming Mode is entered
when the TST pin and the PA0 and PA1 pins are all tied high and PA2 is tied low.
8.10 SAM-BA Boot Assistant
The SAM-BA™ Boot Recovery restores the SAM-BA Boot in the first two sectors of the on-chip
Flash memory. The SAM-BA Boot recovery is performed when the TST pin and the PA0, PA1
and PA2 pins are all tied high for 10 seconds.
25
6175GS–ATARM–24-Dec-08
The SAM-BA Boot Assistant is a default Boot Program that provides an easy way to program in
situ the on-chip Flash memory.
The SAM-BA Boot Assistant supports serial communication through the DBGU or through the
USB Device Port. (The AT91SAM7S32/16 have no USB Device Port.)
• Communication through the DBGU supports a wide range of crystals from 3 to 20 MHz via
software auto-detection.
• Communication through the USB Device Port is limited to an 18.432 MHz crystal. (
The SAM-BA Boot provides an interface with SAM-BA Graphic User Interface (GUI).
9. System Controller
The System Controller manages all vital blocks of the microcontroller: interrupts, clocks, power,
time, debug and reset.
The System Controller peripherals are all mapped to the highest 4 Kbytes of address space,
between addresses 0xFFFF F000 and 0xFFFF FFFF.
Figure 9-1 on page 27 and Figure 9-2 on page 28 show the product specific System Controller
Block Diagrams.
Figure 8-1 on page 20 shows the mapping of the of the User Interface of the System Controller
peripherals. Note that the memory controller configuration user interface is also mapped within
this address space.
26
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Figure 9-1. System Controller Block Diagram (AT91SAM7S512/256/128/64/321/161)
jtag_nreset
Boundary Scan
TAP Controller
System Controller
nirq
nfiq
irq0-irq1
fiq
Advanced
Interrupt
Controller
proc_nreset
ARM7TDMI
periph_irq[2..14]
PCK
int
debug
pit_irq
rtt_irq
wdt_irq
dbgu_irq
pmc_irq
rstc_irq
power_on_reset
force_ntrst
MCK
periph_nreset
dbgu_irq
Debug
Unit
force_ntrst
dbgu_rxd
dbgu_txd
pit_irq
security_bit
MCK
debug
Periodic
Interval
Timer
power_on_reset
flash_poe
SLCK
Real-Time
Timer
Embedded
Flash
rtt_irq
flash_wrdis
power_on_reset
cal
SLCK
debug
Watchdog
Timer
gpnvm[0..1]
wdt_irq
idle
proc_nreset
cal
gpnvm[0]
wdt_fault
WDRPROC
gpnvm[1]
MCK
en
bod_rst_en
Memory
Controller
flash_wrdis
proc_nreset
BOD
power_on_reset
jtag_nreset
flash_poe
periph_nreset
proc_nreset
Reset
Controller
Voltage
Regulator
Mode
POR
standby
cal
Voltage
Controller
rstc_irq
Regulator
NRST
SLCK
SLCK
RCOSC
OSC
periph_clk[2..14]
pck[0-2]
UDPCK
periph_clk[11]
USB Device
XIN
Power
Management
Controller
Port
MAINCK
periph_nreset
periph_irq[11]
usb_suspend
PCK
XOUT
UDPCK
MCK
PLLRC
PLL
PLLCK
int
pmc_irq
idle
periph_nreset
periph_clk[4..14]
usb_suspend
periph_nreset
Embedded
Peripherals
periph_nreset
periph_clk[2]
dbgu_rxd
periph_irq{2]
irq0-irq1
fiq
periph_irq[4..14]
PIO
Controller
dbgu_txd
in
PA0-PA31
out
enable
27
6175GS–ATARM–24-Dec-08
Figure 9-2. System Controller Block Diagram (AT91SAM7S32/16)
System Controller
jtag_nreset
Boundary Scan
TAP Controller
nirq
nfiq
irq0
Advanced
Interrupt
Controller
fiq
proc_nreset
ARM7TDMI
periph_irq[2..14]
PCK
int
debug
pit_irq
rtt_irq
wdt_irq
dbgu_irq
pmc_irq
rstc_irq
power_on_reset
force_ntrst
MCK
dbgu_irq
periph_nreset
Debug
Unit
force_ntrst
dbgu_rxd
dbgu_txd
pit_irq
security_bit
MCK
debug
Periodic
Interval
Timer
periph_nreset
flash_poe
SLCK
Real-Time
Timer
Embedded
Flash
rtt_irq
flash_wrdis
power_on_reset
cal
SLCK
debug
Watchdog
Timer
gpnvm[0..1]
wdt_irq
idle
proc_nreset
cal
gpnvm[0]
wdt_fault
WDRPROC
gpnvm[1]
MCK
en
bod_rst_en
Memory
Controller
flash_wrdis
proc_nreset
BOD
power_on_reset
jtag_nreset
flash_poe
periph_nreset
proc_nreset
Reset
Controller
Voltage
Regulator
Mode
POR
standby
cal
Voltage
Controller
rstc_irq
Regulator
NRST
SLCK
SLCK
RCOSC
OSC
periph_clk[2..14]
pck[0-2]
XIN
Power
Management
Controller
MAINCK
PCK
MCK
XOUT
PLLRC
PLL
PLLCK
int
pmc_irq
idle
periph_nreset
periph_clk[4..14]
periph_nreset
Embedded
Peripherals
periph_nreset
periph_clk[2]
dbgu_rxd
periph_irq{2]
irq0
periph_irq[4..14]
PIO
fiq
Controller
dbgu_txd
in
PA0-PA20
out
enable
28
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
9.1
Reset Controller
The Reset Controller is based on a power-on reset cell and one brownout detector. It gives the
status of the last reset, indicating whether it is a power-up reset, a software reset, a user reset, a
watchdog reset or a brownout reset. In addition, it controls the internal resets and the NRST pin
open-drain output. It allows to shape a signal on the NRST line, guaranteeing that the length of
the pulse meets any requirement.
Note that if NRST is used as a reset output signal for external devices during power-off, the
brownout detector must be activated.
9.1.1
Brownout Detector and Power-on Reset
The AT91SAM7S Series embeds a brownout detection circuit and a power-on reset cell. Both
are supplied with and monitor VDDCORE. Both signals are provided to the Flash to prevent any
code corruption during power-up or power-down sequences or if brownouts occur on the
VDDCORE power supply.
The power-on reset cell has a limited-accuracy threshold at around 1.5V. Its output remains low
during power-up until VDDCORE goes over this voltage level. This signal goes to the reset con-
troller and allows a full re-initialization of the device.
The brownout detector monitors the VDDCORE level during operation by comparing it to a fixed
trigger level. It secures system operations in the most difficult environments and prevents code
corruption in case of brownout on the VDDCORE.
Only VDDCORE is monitored.
When the brownout detector is enabled and VDDCORE decreases to a value below the trigger
level (Vbot-, defined as Vbot - hyst/2), the brownout output is immediately activated.
When VDDCORE increases above the trigger level (Vbot+, defined as Vbot + hyst/2), the reset
is released. The brownout detector only detects a drop if the voltage on VDDCORE stays below
the threshold voltage for longer than about 1µs.
The threshold voltage has a hysteresis of about 50 mV, to ensure spike free brownout detection.
The typical value of the brownout detector threshold is 1.68V with an accuracy of 2ꢀ and is
factory calibrated.
The brownout detector is low-power, as it consumes less than 20 µA static current. However, it
can be deactivated to save its static current. In this case, it consumes less than 1µA. The deac-
tivation is configured through the GPNVM bit 0 of the Flash.
29
6175GS–ATARM–24-Dec-08
9.2
Clock Generator
The Clock Generator embeds one low-power RC Oscillator, one Main Oscillator and one PLL
with the following characteristics:
• RC Oscillator ranges between 22 kHz and 42 kHz
• Main Oscillator frequency ranges between 3 and 20 MHz
• Main Oscillator can be bypassed
• PLL output ranges between 80 and 220 MHz
It provides SLCK, MAINCK and PLLCK.
Figure 9-3. Clock Generator Block Diagram
Clock Generator
Embedded
RC
Oscillator
Slow Clock
SLCK
XIN
Main
Oscillator
Main Clock
MAINCK
XOUT
PLL and
Divider
PLL Clock
PLLCK
PLLRC
Status
Power
Control
Management
Controller
9.3
Power Management Controller
The Power Management Controller uses the Clock Generator outputs to provide:
• the Processor Clock PCK
• the Master Clock MCK
• the USB Clock UDPCK (not present on AT91SAM7S32/16)
• all the peripheral clocks, independently controllable
• three programmable clock outputs
The Master Clock (MCK) is programmable from a few hundred Hz to the maximum operating fre-
quency of the device.
The Processor Clock (PCK) switches off when entering processor idle mode, thus allowing
reduced power consumption while waiting for an interrupt.
30
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Figure 9-4. Power Management Controller Block Diagram
Processor
Clock
Controller
PCK
int
Master Clock Controller
Idle Mode
SLCK
MAINCK
PLLCK
Prescaler
/1,/2,/4,...,/64
MCK
Peripherals
Clock Controller
periph_clk[2..14]
ON/OFF
Programmable Clock Controller
SLCK
MAINCK
PLLCK
Prescaler
/1,/2,/4,...,/64
pck[0..2]
USB Clock Controller
ON/OFF
usb_suspend
UDPCK
Divider
/1,/2,/4
PLLCK
9.4
Advanced Interrupt Controller
• Controls the interrupt lines (nIRQ and nFIQ) of an ARM Processor
• Individually maskable and vectored interrupt sources
– Source 0 is reserved for the Fast Interrupt Input (FIQ)
– Source 1 is reserved for system peripherals RTT, PIT, EFC, PMC, DBGU, etc.)
– Other sources control the peripheral interrupts or external interrupts
– Programmable edge-triggered or level-sensitive internal sources
– Programmable positive/negative edge-triggered or high/low level-sensitive external
sources
• 8-level Priority Controller
– Drives the normal interrupt of the processor
– Handles priority of the interrupt sources
– Higher priority interrupts can be served during service of lower priority interrupt
• Vectoring
– Optimizes interrupt service routine branch and execution
– One 32-bit vector register per interrupt source
– Interrupt vector register reads the corresponding current interrupt vector
• Protect Mode
– Easy debugging by preventing automatic operations
• Fast Forcing
– Permits redirecting any interrupt source on the fast interrupt
• General Interrupt Mask
– Provides processor synchronization on events without triggering an interrupt
31
6175GS–ATARM–24-Dec-08
9.5
Debug Unit
• Comprises:
– One two-pin UART
– One Interface for the Debug Communication Channel (DCC) support
– One set of Chip ID Registers
– One Interface providing ICE Access Prevention
• Two-pin UART
– Implemented features are compatible with the USART
– Programmable Baud Rate Generator
– Parity, Framing and Overrun Error
– Automatic Echo, Local Loopback and Remote Loopback Channel Modes
• Debug Communication Channel Support
– Offers visibility of COMMRX and COMMTX signals from the ARM Processor
• Chip ID Registers
– Identification of the device revision, sizes of the embedded memories, set of
peripherals
– Chip ID is 0x270B0A40 for AT91SAM7S512 Rev A
– Chip ID is 0x270B0940 for AT91SAM7S256 Rev A
– Chip ID is 0x270B0941 for AT91SAM7S256 Rev B
– Chip ID is 0x270A0740 for AT91SAM7S128 Rev A
– Chip ID is 0x270A0741 for AT91SAM7S128 Rev B
– Chip ID is 0x27090540 for AT91SAM7S64 Rev A
– Chip ID is 0x27090543 for AT91SAM7S64 Rev B
– Chip ID is 0x27080342 for AT91SAM7S321 Rev A
– Chip ID is 0x27080340 for AT91SAM7S32 Rev A
– Chip ID is 0x27080341 for AT91SAM7S32 Rev B
– Chip ID is 0x27050241 for AT9SAM7S161 Rev A
– Chip ID is 0x27050240 for AT91SAM7S16 Rev A
Note:
Refer to the errata section of the datasheet for updates on chip ID.
9.6
9.7
Periodic Interval Timer
• 20-bit programmable counter plus 12-bit interval counter
Watchdog Timer
• 12-bit key-protected Programmable Counter running on prescaled SCLK
• Provides reset or interrupt signals to the system
• Counter may be stopped while the processor is in debug state or in idle mode
9.8
Real-time Timer
• 32-bit free-running counter with alarm running on prescaled SCLK
• Programmable 16-bit prescaler for SLCK accuracy compensation
32
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
9.9
PIO Controller
• One PIO Controller, controlling 32 I/O lines (21 for AT91SAM7S32/16)
• Fully programmable through set/clear registers
• Multiplexing of two peripheral functions per I/O line
• For each I/O line (whether assigned to a peripheral or used as general-purpose I/O)
– Input change interrupt
– Half a clock period glitch filter
– Multi-drive option enables driving in open drain
– Programmable pull-up on each I/O line
– Pin data status register, supplies visibility of the level on the pin at any time
• Synchronous output, provides Set and Clear of several I/O lines in a single write
9.10 Voltage Regulator Controller
The aim of this controller is to select the Power Mode of the Voltage Regulator between Normal
Mode (bit 0 is cleared) or Standby Mode (bit 0 is set).
33
6175GS–ATARM–24-Dec-08
10. Peripherals
10.1 User Interface
The User Peripherals are mapped in the 256 MBytes of address space between 0xF000 0000
and 0xFFFF EFFF. Each peripheral is allocated 16 Kbytes of address space.
A complete memory map is provided in Figure 8-1 on page 20.
10.2 Peripheral Identifiers
The AT91SAM7S Series embeds a wide range of peripherals. Table 10-1 defines the Peripheral
Identifiers of the AT91SAM7S512/256/128/64/321/161. Table 10-2 defines the Peripheral Identi-
fiers of the AT91SAM7S32/16. A peripheral identifier is required for the control of the peripheral
interrupt with the Advanced Interrupt Controller and for the control of the peripheral clock with
the Power Management Controller.
Table 10-1. Peripheral Identifiers (AT91SAM7S512/256/128/64/321/161)
Peripheral
ID
Peripheral
Mnemonic
Peripheral
Name
External
Interrupt
0
AIC
Advanced Interrupt Controller
System
FIQ
1
SYSC(1)
PIOA
Reserved
ADC(1)
SPI
2
Parallel I/O Controller A
3
4
Analog-to Digital Converter
Serial Peripheral Interface
USART 0
5
6
US0
7
US1
USART 1
8
SSC
Synchronous Serial Controller
Two-wire Interface
PWM Controller
9
TWI
10
11
12
13
14
15 - 29
30
31
PWMC
UDP
USB Device Port
Timer/Counter 0
TC0
TC1
Timer/Counter 1
TC2
Timer/Counter 2
Reserved
AIC
Advanced Interrupt Controller
Advanced Interrupt Controller
IRQ0
IRQ1
AIC
Note:
1. Setting SYSC and ADC bits in the clock set/clear registers of the PMC has no effect. The Sys-
tem Controller is continuously clocked. The ADC clock is automatically started for the first
conversion. In Sleep Mode the ADC clock is automatically stopped after each conversion.
34
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Table 10-2. Peripheral Identifiers (AT91SAM7S32/16)
Peripheral
ID
Peripheral
Mnemonic
Peripheral
Name
External
Interrupt
0
AIC
SYSC(1)
Advanced Interrupt Controller
System
FIQ
1
2
PIOA
Parallel I/O Controller A
3
Reserved
ADC(1)
SPI
4
Analog-to Digital Converter
Serial Peripheral Interface
USART
5
6
US
7
Reserved
SSC
8
Synchronous Serial Controller
Two-wire Interface
9
TWI
10
11
12
13
14
15 - 29
30
31
PWMC
Reserved
TC0
PWM Controller
Timer/Counter 0
Timer/Counter 1
Timer/Counter 2
TC1
TC2
Reserved
AIC
Advanced Interrupt Controller
IRQ0
Reserved
Note:
1. Setting SYSC and ADC bits in the clock set/clear re gisters of the PMC has no effect. The Sys-
tem Controller is continuously clocked. The ADC clock is automatically started for the first
conversion. In Sleep Mode the ADC clock is automatically stopped after each conversion.
10.3 Peripheral Multiplexing on PIO Lines
The AT91SAM7S Series features one PIO controller, PIOA, that multiplexes the I/O lines of the
peripheral set.
PIO Controller A controls 32 lines (21 lines for AT91SAM7S32/16). Each line can be assigned to
one of two peripheral functions, A or B. Some of them can also be multiplexed with the analog
inputs of the ADC Controller.
Table 10-3, “Multiplexing on PIO Controller A (AT91SAM7S512/256/128/64/321/161),” on
page 36 and Table 10-4, “Multiplexing on PIO Controller A (AT91SAM7S32/16),” on page 37
define how the I/O lines of the peripherals A, B or the analog inputs are multiplexed on the PIO
Controller A. The two columns “Function” and “Comments” have been inserted for the user’s
own comments; they may be used to track how pins are defined in an application.
Note that some peripheral functions that are output only may be duplicated in the table.
All pins reset in their Parallel I/O lines function are configured as input with the programmable
pull-up enabled, so that the device is maintained in a static state as soon as a reset is detected.
35
6175GS–ATARM–24-Dec-08
10.4 PIO Controller A Multiplexing
Table 10-3. Multiplexing on PIO Controller A (AT91SAM7S512/256/128/64/321/161)
PIO Controller A
Peripheral B
Application Usage
Function Comments
I/O Line
PA0
Peripheral A
PWM0
PWM1
PWM2
TWD
Comments
High-Drive
High-Drive
High-Drive
High-Drive
TIOA0
TIOB0
SCK0
PA1
PA2
PA3
NPCS3
TCLK0
NPCS3
PCK0
PA4
TWCK
RXD0
TXD0
RTS0
CTS0
DRXD
DTXD
NPCS0
MISO
MOSI
SPCK
TF
PA5
PA6
PA7
PWM3
ADTRG
NPCS1
NPCS2
PWM0
PWM1
PWM2
PWM3
TIOA1
TIOB1
PCK1
PA8
PA9
PA10
PA11
PA12
PA13
PA14
PA15
PA16
PA17
PA18
PA19
PA20
PA21
PA22
PA23
PA24
PA25
PA26
PA27
PA28
PA29
PA30
PA31
TK
TD
AD0
AD1
AD2
AD3
RD
PCK2
RK
FIQ
RF
IRQ0
RXD1
TXD1
SCK1
RTS1
CTS1
DCD1
DTR1
DSR1
RI1
PCK1
NPCS3
PWM0
PWM1
PWM2
TIOA2
TIOB2
TCLK1
TCLK2
NPCS2
PCK2
IRQ1
NPCS1
36
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Table 10-4. Multiplexing on PIO Controller A (AT91SAM7S32/16)
PIO Controller A
Application Usage
I/O Line
PA0
Peripheral A
PWM0
PWM1
PWM2
TWD
Peripheral B
TIOA0
TIOB0
SCK0
Comments
High-Drive
High-Drive
High-Drive
High-Drive
Function
Comments
PA1
PA2
PA3
NPCS3
TCLK0
NPCS3
PCK0
PA4
TWCK
RXD0
TXD0
RTS0
CTS0
DRXD
DTXD
NPCS0
MISO
MOSI
SPCK
TF
PA5
PA6
PA7
PWM3
ADTRG
NPCS1
NPCS2
PWM0
PWM1
PWM2
PWM3
TIOA1
TIOB1
PCK1
PA8
PA9
PA10
PA11
PA12
PA13
PA14
PA15
PA16
PA17
PA18
PA19
PA20
TK
TD
AD0
AD1
AD2
AD3
RD
PCK2
RK
FIQ
RF
IRQ0
37
6175GS–ATARM–24-Dec-08
10.5 Serial Peripheral Interface
• Supports communication with external serial devices
– Four chip selects with external decoder allow communication with up to 15
peripherals
– Serial memories, such as DataFlash® and 3-wire EEPROMs
– Serial peripherals, such as ADCs, DACs, LCD Controllers, CAN Controllers and
Sensors
– External co-processors
• Master or slave serial peripheral bus interface
– 8- to 16-bit programmable data length per chip select
– Programmable phase and polarity per chip select
– Programmable transfer delays between consecutive transfers and between clock
and data per chip select
– Programmable delay between consecutive transfers
– Selectable mode fault detection
– Maximum frequency at up to Master Clock
10.6 Two-wire Interface
• Master Mode only (AT91SAM7S512/256/128/64/321/32)
• Master, Multi-Master and Slave Mode support (AT91SAM7S161/16)
• General Call supported in Slave Mode (AT91SAM7S161/16)
• Compatibility with I2C compatible devices (refer to the TWI sections of the datasheet)
• One, two or three bytes internal address registers for easy Serial Memory access
• 7-bit or 10-bit slave addressing
• Sequential read/write operations
10.7 USART
• Programmable Baud Rate Generator
• 5- to 9-bit full-duplex synchronous or asynchronous serial communications
– 1, 1.5 or 2 stop bits in Asynchronous Mode
– 1 or 2 stop bits in Synchronous Mode
– Parity generation and error detection
– Framing error detection, overrun error detection
– MSB or LSB first
– Optional break generation and detection
– By 8 or by 16 over-sampling receiver frequency
– Hardware handshaking RTS - CTS
– Modem Signals Management DTR-DSR-DCD-RI on USART1 (not present on
AT91SAM7S32/16)
– Receiver time-out and transmitter timeguard
– Multi-drop Mode with address generation and detection
• RS485 with driver control signal
38
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
• ISO7816, T = 0 or T = 1 Protocols for interfacing with smart cards
– NACK handling, error counter with repetition and iteration limit
• IrDA modulation and demodulation
– Communication at up to 115.2 Kbps
• Test Modes
– Remote Loopback, Local Loopback, Automatic Echo
10.8 Serial Synchronous Controller
• Provides serial synchronous communication links used in audio and telecom applications
• Contains an independent receiver and transmitter and a common clock divider
• Offers a configurable frame sync and data length
• Receiver and transmitter can be programmed to start automatically or on detection of
different event on the frame sync signal
• Receiver and transmitter include a data signal, a clock signal and a frame synchronization
signal
10.9 Timer Counter
• Three 16-bit Timer Counter Channels
– Two output compare or one input capture per channel (except for AT91SAM7S32/16
which have only two channels connected to the PIO)
• Wide range of functions including:
– Frequency measurement
– Event counting
– Interval measurement
– Pulse generation
– Delay timing
– Pulse Width Modulation
– Up/down capabilities
• Each channel is user-configurable and contains:
– Three external clock inputs (The AT91SAM7S32/16 have one)
– Five internal clock inputs, as defined in Table 10-5
Table 10-5. Timer Counter Clocks Assignment
TC Clock Input
TIMER_CLOCK1
TIMER_CLOCK2
TIMER_CLOCK3
TIMER_CLOCK4
TIMER_CLOCK5
Clock
MCK/2
MCK/8
MCK/32
MCK/128
MCK/1024
– Two multi-purpose input/output signals
– Two global registers that act on all three TC channels
39
6175GS–ATARM–24-Dec-08
10.10 PWM Controller
• Four channels, one 16-bit counter per channel
• Common clock generator, providing thirteen different clocks
– One Modulo n counter providing eleven clocks
– Two independent linear dividers working on modulo n counter outputs
• Independent channel programming
– Independent enable/disable commands
– Independent clock selection
– Independent period and duty cycle, with double buffering
– Programmable selection of the output waveform polarity
– Programmable center or left aligned output waveform
10.11 USB Device Port (Does not pertain to AT91SAM7S32/16)
• USB V2.0 full-speed compliant, 12 Mbits per second.
• Embedded USB V2.0 full-speed transceiver
• Embedded 328-byte dual-port RAM for endpoints
• Four endpoints
– Endpoint 0: 8 bytes
– Endpoint 1 and 2: 64 bytes ping-pong
– Endpoint 3: 64 bytes
– Ping-pong Mode (two memory banks) for isochronous and bulk endpoints
• Suspend/resume logic
10.12 Analog-to-digital Converter
• 8-channel ADC
• 10-bit 384 Ksamples/sec. or 8-bit 583 Ksamples/sec. Successive Approximation Register
ADC
• 2 LSB Integral Non Linearity, 1 LSB Differential Non Linearity
• Integrated 8-to-1 multiplexer, offering eight independent 3.3V analog inputs
• External voltage reference for better accuracy on low voltage inputs
• Individual enable and disable of each channel
• Multiple trigger source
– Hardware or software trigger
– External trigger pin
– Timer Counter 0 to 2 outputs TIOA0 to TIOA2 trigger
• Sleep Mode and conversion sequencer
– Automatic wakeup on trigger and back to sleep mode after conversions of all
enabled channels
• Four of eight analog inputs shared with digital signals
40
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
11. Package Drawings
The SAM7S series devices are available in LQFP and QFN package types.
11.1 LQFP Packages
Figure 11-1. 48-and 64-lead LQFP Package Drawing
41
6175GS–ATARM–24-Dec-08
Table 11-1. 48-lead LQFP Package Dimensions (in mm)
Millimeter
Inch
Symbol
Min
–
Nom
Max
1.60
0.15
1.45
Min
–
Nom
Max
0.063
0.006
0.057
A
A1
A2
D
–
–
0.05
1.35
–
1.40
0.002
0.053
–
0.055
0.354 BSC
0.276 BSC
0.354 BSC
0.276 BSC
–
9.00 BSC
7.00 BSC
9.00 BSC
7.00 BSC
–
D1
E
E1
R2
R1
q
0.08
0.08
0°
0.20
–
0.003
0.003
0°
0.008
–
–
–
3.5°
7°
3.5°
7°
θ1
θ2
θ3
c
0°
–
–
0°
–
–
11°
11°
0.09
0.45
12°
13°
13°
0.20
0.75
11°
12°
13°
13°
0.008
0.030
12°
11°
12°
–
0.004
0.018
–
L
0.60
0.024
0.039 REF
–
L1
S
1.00 REF
–
0.20
0.17
–
0.008
0.007
–
b
0.20
0.27
0.008
0.020 BSC.
0.217
0.217
0.011
e
0.50 BSC.
5.50
D2
E2
5.50
Tolerances of Form and Position
0.20
aaa
bbb
ccc
ddd
0.008
0.008
0.003
0.003
0.20
0.08
0.08
42
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Table 11-2. 64-lead LQFP Package Dimensions (in mm)
Millimeter
Inch
Symbol
Min
–
Nom
Max
1.60
0.15
1.45
Min
–
Nom
Max
0.063
0.006
0.057
A
A1
A2
D
–
–
0.05
1.35
–
0.002
0.053
–
0.055
0.472 BSC
0.383 BSC
0.472 BSC
0.383 BSC
–
1.40
12.00 BSC
D1
E
10.00 BSC
12.00 BSC
E1
R2
R1
q
10.00 BSC
0.08
0.08
0°
–
–
0.20
–
0.003
0.003
0°
0.008
–
–
3.5°
–
7°
3.5°
7°
θ1
θ2
θ3
c
0°
–
0°
–
–
11°
11°
0.09
0.45
12°
13°
13°
0.20
0.75
11°
12°
13°
13°
0.008
0.030
12°
11°
12°
–
0.004
0.018
–
L
0.60
1.00 REF
–
0.024
0.039 REF
–
L1
S
0.20
0.17
–
0.008
0.007
–
b
0.20
0.50 BSC.
7.50
7.50
0.27
0.008
0.020 BSC.
0.285
0.285
0.011
e
D2
E2
Tolerances of Form and Position
0.20
aaa
bbb
ccc
ddd
0.008
0.008
0.003
0.003
0.20
0.08
0.08
43
6175GS–ATARM–24-Dec-08
11.2 QFN Packages
Figure 11-2. 48-pad QFN Package
44
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Table 11-3. 48-pad QFN Package Dimensions (in mm)
Millimeter
Nom
–
Inch
Nom
Symbol
Min
–
Max
090
Min
–
Max
0.035
0.002
0.028
A
A1
A2
A3
b
–
–
–
0.050
0.70
–
–
–
0.65
–
0.026
0.008 REF
0.008
0.276 bsc
0.220
0.276 bsc
0.220
0.016
0.020 bsc
–
0.20 REF
0.20
0.18
5.45
0.23
5.75
0.007
0.215
0.009
0.226
D
7.00 bsc
5.60
D2
E
7.00 bsc
5.60
E2
L
5.45
0.35
5.75
0.45
0.215
0.014
0.226
0.018
0.40
e
0.50 bsc
–
R
0.09
–
0.004
–
Tolerances of Form and Position
0.10
aaa
bbb
ccc
0.004
0.004
0.002
0.10
0.05
45
6175GS–ATARM–24-Dec-08
Figure 11-3. 64-pad QFN Package Drawing
l
e
46
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Table 11-4. 64-pad QFN Package Dimensions (in mm)
Millimeter
Nom
–
Inch
Nom
Symbol
Min
–
Max
090
Min
–
Max
0.035
0.001
0.028
A
A1
A2
A3
b
–
–
–
0.05
0.70
–
–
–
0.65
–
0.026
0.008 REF
0.010
0.354 bsc
0.280
0.354 bsc
0.280
0.016
0.020 bsc
–
0.20 REF
0.25
0.23
6.95
0.28
7.25
0.009
0.274
0.011
0.285
D
9.00 bsc
7.10
D2
E
9.00 bsc
7.10
E2
L
6.95
0.35
7.25
0.45
0.274
0.014
0.285
0.018
0.40
e
0.50 bsc
–
R
0.125
–
0.0005
–
Tolerances of Form and Position
0.10
aaa
bbb
ccc
0.004
0.004
0.002
0.10
0.05
47
6175GS–ATARM–24-Dec-08
12. AT91SAM7S Ordering Information
Table 12-1. AT91SAM7S Series Ordering Information
Temperature
MLR A Ordering Code
MLR B Ordering Code
Package
Package Type
Operating Range
AT91SAM7S16-AU
AT91SAM7S16-MU
LQFP 48
QFN 48
Industrial
(-40⋅ C to 85⋅ C)
–
Green
Industrial
(-40⋅ C to 85⋅ C)
AT91SAM7S161-AU
–
LQFP 64
Green
Green
Green
Green
Green
Green
Green
AT91SAM7S32-AU-001
AT91SAM7S32-MU
AT91SAM7S32B-AU
AT91SAM7S32B-MU
LQFP 48
QFN 48
Industrial
(-40⋅ C to 85⋅ C)
AT91SAM7S321-AU
AT91SAM7S321-MU
LQFP 64
QFN 64
Industrial
(-40⋅ C to 85⋅ C)
–
AT91SAM7S64-AU-001
AT91SAM7S64-MU
AT91SAM7S64B-AU
AT91SAM7S64B-MU
LQFP 64
QFN 64
Industrial
(-40⋅ C to 85⋅ C)
AT91SAM7S128-AU-001
AT91SAM7S128-MU
LQFP 64
QFN 64
Industrial
(-40⋅ C to 85⋅ C)
–
–
AT91SAM7S256-AU-001
AT91SAM7S256-MU
LQFP 64
QFN 64
Industrial
(-40⋅ C to 85⋅ C)
AT91SAM7S512-AU
AT91SAM7S512-MU
LQFP 64
QFN 64
Industrial
(-40⋅ C to 85⋅ C)
–
48
AT91SAM7S Series Summary
6175GS–ATARM–24-Dec-08
AT91SAM7S Series Summary
Revision History
Change
Request
Ref.
Doc. Rev
Comments
First issue - Unqualified on Intranet
Corresponds to 6175A full datasheet approval loop.
Qualified on Intranet.
6175AS
6175BS
6175CS
Section 8. “Memories” on page 18 updated: 2 ms => 3 ms, 10 ms => 15 ms, 4 ms => 6 ms
CSR05-529
#2342
Section 12. ”AT91SAM7S Ordering Information” AT91SAM7S321 changed in Table 12-1 on page 48
“Features”, Table 1-1, “Configuration Summary,” on page 3, Section 4. ”Package and Pinout”
Section 12. ”AT91SAM7S Ordering Information” QFN package information added
6175DS
6175ES
#2444
specs
Section 10.11 on page 40 USB Device port, Ping-pong Mode includes Isochronous endpoints.
“Features” on page 1, and global: AT91SAM7S512 added to series. Reference to Manchester Encoder
removed from USART.
Section 8. ”Memories” Reformatted Memories, Consolidated Memory Mapping in Figure 8-1 on page 20
Section 10. ”Peripherals” Reordered sub sections.
#2748
Section 11. ”Package Drawings” QFN, LQFP package drawings added.
“ice_nreset” signals changed to” power_on_reset” in System Controller block diagrams, Figure 9-1 on
page 27 and Figure 9-2 on page 28.
#2832
(DBGU IP)
Section 4. ”Package and Pinout” LQFP and QFN Package Outlines replace Mechanical Overview.
Section 10.1 ”User Interface”, User peripherals are mapped between 0xF000 0000 and 0xFFFF EFFF.
SYSIRQ changed to SYSC in “Peripheral Identifiers” Table 10-1 and Table 10-2
rfo review
6175FS
AT91SAM7S161 and AT91SAM7S16 added to product family
BDs
Features: Timer Counter, on page 2 product specific information rewritten, Table 1-1, “Configuration
Summary,” on page 3, footnote explains TC on AT91SAM7S32/16 has only two channels accessible via
PIO, and in Section 10.9 ”Timer Counter”, precisions added to “compare and capture” output/input.
4208
Section 10.6 ”Two-wire Interface”, updated reference to I2C compatibility, internal address registers,
slave addressing, Modes for AT91SAM7S161/16
rfo review
“One Two-wire Interface (TWI)” on page 2, updated in Features
Section 10.12 ”Analog-to-digital Converter”, updated Successive Approximation Register ADC and the
INL, DNL values of LSB.
Section 8.8.3 ”Lock Regions”, locked-region’s erase or program command updated
Section 9.5 ”Debug Unit”, Chip ID updated.
4325
5063
5846
Section 6. ”I/O Lines Considerations”, JTAG Port Pin, Test Pin, Erase Pin, updated.
6175GS
“Features”,“Debug Unit (DBGU)” updated with “Mode for General Purpose 2-wire UART Serial
Communication”
Section 7.4 ”Peripheral DMA Controller”, added list of PDC priorities.
5913
5224
5685
rfo
Section 9. ”System Controller”, Figure 9-1 and Figure 9-2 RTT is reset by “power_on_reset”.
Section 9.1.1 ”Brownout Detector and Power-on Reset”, fourth paragraph reduced.
Section 9.5 ”Debug Unit”, the list; Section • ”Chip ID Registers”, chip IDs updated, added SAM7S32 Rev
B and SAM7S64 Rev B to the list.
Section 12. ”AT91SAM7S Ordering Information”, Updated product ordering information by MRL A and
MRL B versions.
49
6175GS–ATARM–24-Dec-08
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Atmel Europe
Le Krebs
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Unit 1-5 & 16, 19/F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
Hong Kong
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-en-
Yvelines Cedex
France
Tel: (852) 2245-6100
Fax: (852) 2722-1369
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Product Contact
Web Site
www.atmel.com
www.atmel.com/AT91SAM
Technical Support
AT91SAM Support
Atmel techincal support
Sales Contacts
www.atmel.com/contacts/
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifica-
tions and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically pro-
vided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted
for use as components in applications intended to support or sustain life.
© 2008 Atmel Corporation. All rights reserved. Atmel®, Atmel logo and combinations thereof, DataFlash®, SAM-BA® and others are registered trade-
marks or trademarks of Atmel Corporation or its subsidiaries. ARM®, the ARM Powered® logo, ARM7TDMI®, Thumb®,nd others are registered trademarks
or trademarks of ARM Limited. Other terms and product names may be the trademarks of others.
6175GS–ATARM–24-Dec-08
AT91SAM7S64B-AU 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
AT91SAM7S64B-MU | ATMEL | AT91 ARM Thumb-based Microcontrollers | 获取价格 | |
AT91SAM7S64C-AU | ATMEL | ARM-based Flash MCU | 获取价格 | |
AT91SAM7S64C-AU-999 | ATMEL | RISC Microcontroller, 32-Bit, FLASH, 55MHz, CMOS, PQFP64, GREEN, MS-026, LQFP-64 | 获取价格 | |
AT91SAM7S64C-AU-999 | MICROCHIP | IC MCU 32BIT 64KB FLASH 64LQFP | 获取价格 | |
AT91SAM7S64C-MU | ATMEL | ARM-based Flash MCU | 获取价格 | |
AT91SAM7S64C-MU | MICROCHIP | IC MCU 32BIT 64KB FLASH 64QFN | 获取价格 | |
AT91SAM7S64C-MU-999 | MICROCHIP | IC MCU 32BIT 64KB FLASH 64QFN | 获取价格 | |
AT91SAM7S64_05 | ATMEL | AT91 ARM Thumb-based Microcontrollers | 获取价格 | |
AT91SAM7SE-EK | ATMEL | Atmel Evaluation Kits | 获取价格 | |
AT91SAM7SE256 | ATMEL | Product Description | 获取价格 |
AT91SAM7S64B-AU 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6