AT27BV020-90TU [ATMEL]
2-megabit (256K x 8) Unregulated Battery-Voltage High-speed OTP EPROM; 2兆位( 256K ×8 )非稳压电池电压高速OTP EPROM型号: | AT27BV020-90TU |
厂家: | ATMEL |
描述: | 2-megabit (256K x 8) Unregulated Battery-Voltage High-speed OTP EPROM |
文件: | 总15页 (文件大小:367K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Features
• Fast Read Access Time – 90 ns
• Dual Voltage Range Operation
– Unregulated Battery Power Supply Range, 2.7V to 3.6V
or Standard 5V 10% Supply Range
• Compatible with JEDEC Standard AT27C020
• Low-power CMOS Operation
– 20 µA Max (Less than 1 µA Typical) Standby for VCC = 3.6V
– 29 mW Max Active at 5 MHz for VCC = 3.6V
• Wide Selection of JEDEC Standard Packages
– 32-lead PLCC
2-megabit
(256K x 8)
– 32-lead TSOP
– 32-lead VSOP
Unregulated
Battery-Voltage
High-speed
OTP EPROM
• High Reliability CMOS Technology
– 2,000V ESD Protection
– 200 mA Latch-up Immunity
• Rapid Programming Algorithm – 100 µs/Byte (Typical)
• CMOS and TTL Compatible Inputs and Outputs
– JEDEC Standard for LVTTL and LVBO
• Integrated Product Identification Code
• Industrial Temperature Range
• Green (Pb/Halide-free) Packaging Option
AT27BV020
1. Description
The AT27BV020 is a high-performance, low-power, low-voltage, 2,097,152-bit, one-
time programmable, read-only memory (OTP EPROM) organized as 256K by 8 bits. It
requires only one supply in the range of 2.7 to 3.6V in normal read mode operation,
making it ideal for fast, portable systems using either regulated or unregulated battery
power.
Atmel’s innovative design techniques provide fast speeds that rival 5V parts while
keeping the low power consumption of a 3V supply. At VCC = 2.7V, any byte can be
accessed in less than 90 ns. With a typical power dissipation of only 18 mW at 5 MHz
and VCC = 3V, the AT27BV020 consumes less than one fifth the power of a standard
5V EPROM. Standby mode supply current is typically less than 1 µA at 3V. The
AT27BV020 simplifies system design and stretches battery lifetime even further by
eliminating the need for power supply regulation
The AT27BV020 is available in industry-standard JEDEC approved one-time pro-
grammable (OTP) plastic PLCC, TSOP and VSOP packages, as well as a 42-ball,
1 mm pitch. All devices feature two-line control (CE, OE) to give designers the flexibil-
ity to prevent bus contention.
The AT27BV020 operating with VCC at 3.0V produces TTL level outputs that are com-
patible with standard TTL logic devices operating at VCC = 5.0V. At VCC = 2.7V, the
part is compatible with JEDEC approved low voltage battery operation (LVBO) inter-
face specifications. The device is also capable of standard 5-volt operation making it
ideally suited for dual supply range systems or card products that are pluggable in
both 3-volt and 5-volt hosts.
0902F–EPROM–12/07
Atmel's AT27BV020 has additional features to ensure high quality and efficient production use.
The Rapid Programming Algorithm reduces the time required to program the part and guaran-
tees reliable programming. Programming time is typically only 100 µs/byte. The Integrated
Product Identification Code electronically identifies the device and manufacturer. This feature is
used by industry-standard programming equipment to select the proper programming algorithms
and voltages. The AT27BV020 programs exactly the same way as a standard 5V AT27C020
and uses the same programming equipment.
2. Pin Configurations
Pin Name
Function
A0 - A17
O0 - O7
CE
Addresses
Outputs
Chip Enable
Output Enable
Program Strobe
No Connect
OE
PGM
NC
2.1
32-lead TSOP, VSOP (Type 1) Top View
A11
A9
1
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE
A10
CE
O7
O6
O5
O4
O3
GND
O2
O1
O0
A0
2
A8
3
A13
A14
A17
PGM
VCC
VPP
A16
A15
A12
A7
4
5
6
7
8
9
10
11
12
13
14
15
16
A6
A1
A5
A2
A4
A3
2.2
32-lead PLCC Top View
A7
A6
A5
A4
A3
5
6
7
8
9
29 A14
28 A13
27 A8
26 A9
25 A11
24 OE
23 A10
22 CE
21 O7
A2 10
A1 11
A0 12
O0 13
2
AT27BV020
0902F–EPROM–12/07
AT27BV020
3. System Considerations
Switching between active and standby conditions via the Chip Enable pin may produce transient
voltage excursions. Unless accommodated by the system design, these transients may exceed
datasheet limits, resulting in device nonconformance. At a minimum, a 0.1 µF high frequency,
low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor
should be connected between the VCC and Ground terminals of the device, as close to the
device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards
with large EPROM arrays, a 4.7 µF bulk electrolytic capacitor should be utilized, again con-
nected between the VCC and Ground terminals. This capacitor should be positioned as close as
possible to the point where the power supply is connected to the array.
4. Block Diagram
5. Absolute Maximum Ratings*
Temperature under Bias .................................. -40°C to +85°C
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Storage Temperature..................................... -65°C to +125°C
Voltage on Any Pin with
Respect to Ground .........................................-2.0V to +7.0V(1)
Voltage on A9 with
Respect to Ground ......................................-2.0V to +14.0V(1)
VPP Supply Voltage with
Respect to Ground .......................................-2.0V to +14.0V(1)
Note:
1. Minimum voltage is -0.6V DC which may undershoot to -2.0V for pulses of less than 20 ns.Maximum output pin voltage is
VCC + 0.75V DC which may be exceeded if certain precautions are observed (consult application notes) and which may
overshoot to +7.0V for pulses of less than 20 ns.
3
0902F–EPROM–12/07
6. Operating Modes
Mode/Pin
CE
OE
VIL
VIH
X
PGM
X(1)
X
Ai
VPP
X
VCC
VCC
VCC
VCC
VCC
VCC
VCC
Outputs
DOUT
Read(2)
VIL
X
Ai
Output Disable(2)
Standby(2)
X
X
High-Z
High-Z
DIN
VIH
VIL
VIL
VIH
X
X
X
Rapid Program(3)
PGM Verify(3)
PGM Inhibit(3)
VIH
VIL
X
VIL
VIH
X
Ai
Ai
VPP
VPP
VPP
DOUT
X
High-Z
(4)
A9 = VH
Product Identification(3)(5)
VIL
VIL
X
X
VCC
Identification Code
A0 = VIH or VIL
A1 - A17 = VIL
Notes: 1. X Can be VIL or VIH.
2. Read, output disable, and standby modes require, 2.7V ≤VCC ≤3.6V, or 4.5V ≤VCC ≤5.5V.
3. Refer to Programming Characteristics. Programming modes requires VCC = 6.5V.
4. VH = 12.0 0.5V.
5. Two identifier bytes may be selected. All Ai inputs are held low (VIL), except A9 which is set to VH and A0 which is toggled
low (VIL) to select the Manufacturer’s Identification byte and high (VIH) to select the Device Code byte.
7. DC and AC Operating Conditions for Read Operation
AT27BV020-90
Industrial Operating Temperature (Case)
CC Power Supply
-40°C - 85°C
2.7V to 3.6V
5V 10%
V
4
AT27BV020
0902F–EPROM–12/07
AT27BV020
8. DC and Operating Characteristics for Read Operation
Symbol
Parameter
Condition
Min
Max
Units
VCC = 2.7V to 3.6V
ILI
Input Load Current
Output Leakage Current
VIN = 0V to VCC
1
µA
µA
µA
µA
µA
mA
V
ILO
VOUT = 0V to VCC
5
10
(2)
IPP1
VPP(1) Read/Standby Current VPP = VCC
I
SB1 (CMOS), CE = VCC 0.3V
20
ISB
ICC
VIL
VCC(1) Standby Current
VCC Active Current
Input Low Voltage
ISB2 (TTL), CE = 2.0 to VCC + 0.5V
100
f = 5 MHz, IOUT = 0 mA, CE = VIL, VCC = 3.6V
8
VCC = 3.0 to 3.6V
-0.6
-0.6
0.8
VCC = 2.7 to 3.6V
VCC = 3.0 to 3.6V
VCC = 2.7 to 3.6V
IOL = 2.0 mA
0.2 x VCC
VCC + 0.5
VCC + 0.5
0.4
V
2.0
V
VIH
Input High Voltage
Output Low Voltage
0.7 x VCC
V
V
VOL
I
OL = 100 µA
0.2
V
IOL = 20 µA
0.1
V
IOH = -2.0 mA
2.4
V
VOH
Output High Voltage
I
OH = -100 µA
VCC - 0.2
VCC - 0.1
V
IOH = -20 µA
V
VCC = 4.5V to 5.5V
ILI
Input Load Current
VIN = 0V to VCC
1
µA
µA
µA
µA
mA
mA
V
ILO
Output Leakage Current
VOUT = 0V to VCC
5
10
(2)
IPP1
VPP(1) Read/Standby Current VPP = VCC
ISB1 (CMOS), CE = VCC 0.3V
100
1
ISB
VCC(1) Standby Current
ISB2 (TTL), CE = 2.0 to VCC + 0.5V
f = 5 MHz, IOUT = 0 mA, CE = VIL
ICC
VIL
VIH
VOL
VCC Active Current
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
25
-0.6
2.0
0.8
VCC + 0.5
0.4
V
IOL = 2.1 mA
IOH = -400 µA
V
VOH
2.4
V
Notes: 1. VCC must be applied simultaneously with or before VPP, and removed simultaneously with or after VPP.
2. VPP may be connected directly to VCC, expect during programming. The supply current would then be the sum of ICC and IPP.
5
0902F–EPROM–12/07
9. AC Characteristics for Read Operation
VCC = 2.7V to 3.6V and 4.5V to 5.5V
AT27BV020-90
Symbol
Parameter
Condition
CE = OE = VIL
OE = VIL
Min
Max
90
Units
ns
(3)
tACC
Address to Output Delay
CE to Output Delay
(2)
tCE
90
ns
(2)(3)
tOE
OE to Output Delay
CE = VIL
50
ns
(4)(5)
tDF
OE or CE High to Output Float, Whichever Occurred First
40
ns
Output Hold from Address, CE or OE, Whichever
Occurred First
tOH
0
ns
10. AC Waveforms for Read Operation(1)
Notes: 1. Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified.
2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE
3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC
.
.
4. This parameter is only sampled and is not 100% tested.
5. Output float is defined as the point when data is no longer driven.
6
AT27BV020
0902F–EPROM–12/07
AT27BV020
11. Input Test Waveform and Measurement Level
tR, tF < 20 ns (10% to 90%)
12. Output Test Load
Note: CL = 100 pF including jig capacitance.
l
13. Pin Capacitance
f = 1 MHz, T = 25°C(1)
Symbol
CIN
Typ
4
Max
8
Units
pF
Conditions
VIN = 0V
COUT
8
12
pF
VOUT = 0V
Note:
1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested.
7
0902F–EPROM–12/07
14. Programming Waveforms(1)
Notes: 1. The Input Timing Reference is 0.8V for VIL and 2.0V for VIH.
2. tOE and tDFP are characteristics of the device but must be accommodated by the programmer.
3. When programming the AT27BV020 a 0.1 µF capacitor is required across VPP and ground to suppress spurious voltage
transients.
15. DC Programming Characteristics
TA = 25 5° C, VCC = 6.5 0.25V, VPP = 13.0 0.25V
Limits
Symbol
ILI
Parameter
Test Conditions
Min
Max
10
Units
µA
V
Input Load Current
VIN = VIL,VIH
VIL
Input Low Level
-0.6
2.0
0.8
VIH
Input High Level
VCC + 0.5
0.4
V
VOL
VOH
ICC2
IPP2
VID
Output Low Voltage
IOL = 2.1 mA
IOH = -400 µA
V
Output High Voltage
VCC Supply Current (Program and Verify)
VPP Supply Current
2.4
V
40
20
mA
mA
V
CE = PGM = VIL
A9 Product Identification Voltage
11.5
12.5
8
AT27BV020
0902F–EPROM–12/07
AT27BV020
16. AC Programming Characteristics
TA = 25 5°C, VCC = 6.5 0.25V, VPP = 13.0 0.25V
Limits
Symbol
tAS
Parameter
Test Conditions(1)
Min
2
Max
Units
µs
Address Setup Time
CE Setup Time
tCES
tOES
tDS
2
µs
OE Setup Time
Input Rise and Fall Times:
2
µs
(10% to 90%) 20 ns
Data Setup Time
2
µs
tAH
Address Hold Time
0
µs
Input Pulse Levels:
tDH
Data Hold Time
2
µs
0.45V to 2.4V
tDFP
tVPS
tVCS
tPW
OE High to Output Float Delay(3)
VPP Setup Time
0
130
ns
Input Timing Reference Level:
0.8V to 2.0V
2
µs
VCC Setup Time
2
µs
PGM Program Pulse Width(2)
95
105
150
µs
Output Timing Reference Level:
0.8V to 2.0V
tOE
Data Valid from OE
ns
VPP Pulse Rise Time During
Programming
tPRT
50
ns
Notes: 1. VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP.
2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven –
see timing diagram.
3. Program Pulse width tolerance is 100 µsec 5%.
17. Atmel’s AT27BV020 Integrated Product Identification Code(1)
Pins
Hex
Codes
A0
0
O7
0
O6
0
O5
0
O4
1
O3
1
O2
1
O1
1
O0
0
Data
Manufacturer
Device Type
1E
1
1
0
0
0
0
1
1
0
86
Note:
1. The AT27BV020 has the same Product Identification Code as the AT27C020. Both are programming compatible.
9
0902F–EPROM–12/07
18. RapidProgramming Algorithm
A 100 µs PGM pulse width is used to program. The address is set to the first location. VCC is
raised to 6.5V and VPP is raised to 13.0V. Each address is first programmed with one 100 µs
PGM pulse without verification. Then a verification/reprogramming loop is executed for each
address. In the event a byte fails to pass verification, up to 10 successive 100 µs pulses are
applied with a verification after each pulse. If the byte fails to verify after 10 pulses have been
applied, the part is considered failed. After the byte verifies properly, the next address is
selected until all have been checked. VPP is then lowered to 5.0V and VCC to 5.0V. All bytes are
read again and compared with the original data to determine if the device passes or fails.
10
AT27BV020
0902F–EPROM–12/07
AT27BV020
19. Ordering Information
19.1 Standard Package
I
CC (mA)
VCC = 3.6V
tACC (ns)
Active
Standby
0.02
Ordering Code
Package
Operation Range
90
8
AT27BV020-90JI
AT27BV020-90TI
AT27BV020-90VI
32J
Industrial
32T
32V(1)
(-40°C to 85°C)
Note:
Not recommended for new designs. Use Green package option.
19.2 Green Package Option (Pb/Halide-free)
I
CC (mA)
VCC = 3.6V
tACC (ns)
Active
Standby
0.02
Ordering Code
Package
Operation Range
90
8
AT27BV020-90JU
AT27BV020-90TU
32J
32T
Industrial
(-40°C to 85°C)
Note:
1. The 32-lead VSOP package is not recommended for new designs.
Package Type
32-lead, Plastic J-leaded Chip Carrier (PLCC)
32J
32T
32V
32-lead, Plastic Thin Small Outline Package (TSOP)
32-lead, Plastic Thin Small Outline Package (VSOP)
11
0902F–EPROM–12/07
20. Packaging Information
20.1 32J – PLCC
1.14(0.045) X 45˚
PIN NO. 1
IDENTIFIER
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
E2
E1
E
B1
B
e
A2
A1
D1
D
A
0.51(0.020)MAX
45˚ MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
MIN
3.175
1.524
0.381
12.319
11.354
9.906
14.859
13.894
12.471
0.660
0.330
MAX
3.556
2.413
–
NOM
NOTE
SYMBOL
A
–
D2
A1
A2
D
–
–
–
12.573
D1
D2
E
–
11.506 Note 2
10.922
–
Notes:
1. This package conforms to JEDEC reference MS-016, Variation AE.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
–
15.113
E1
E2
B
–
14.046 Note 2
13.487
–
–
–
0.813
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
B1
e
0.533
1.270 TYP
10/04/01
TITLE
DRAWING NO.
REV.
2325 Orchard Parkway
San Jose, CA 95131
32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC)
32J
B
R
12
AT27BV020
0902F–EPROM–12/07
AT27BV020
20.2 32T – TSOP
PIN 1
0º ~ 8º
c
Pin 1 Identifier
D1
D
L
b
L1
e
A2
E
GAGE PLANE
A
SEATING PLANE
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
MIN
–
MAX
1.20
0.15
1.05
20.20
NOM
–
NOTE
SYMBOL
A
A1
A2
D
0.05
0.95
19.80
18.30
7.90
0.50
–
1.00
Notes:
1. This package conforms to JEDEC reference MO-142, Variation BD.
2. Dimensions D1 and E do not include mold protrusion. Allowable
protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side.
3. Lead coplanarity is 0.10 mm maximum.
20.00
18.40
8.00
D1
E
18.50 Note 2
8.10
0.70
Note 2
L
0.60
L1
b
0.25 BASIC
0.22
0.17
0.10
0.27
0.21
c
–
e
0.50 BASIC
10/18/01
DRAWING NO. REV.
32T
TITLE
2325 Orchard Parkway
San Jose, CA 95131
32T, 32-lead (8 x 20 mm Package) Plastic Thin Small Outline
Package, Type I (TSOP)
B
R
13
0902F–EPROM–12/07
20.3 32V – VSOP
PIN 1
0º ~ 8º
c
Pin 1 Identifier
D1
D
L
b
L1
e
A2
E
GAGE PLANE
A
SEATING PLANE
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
MIN
–
MAX
1.20
0.15
1.05
14.20
NOM
–
NOTE
SYMBOL
A
A1
A2
D
0.05
0.95
13.80
12.30
7.90
0.50
–
1.00
Notes:
1. This package conforms to JEDEC reference MO-142, Variation BA.
2. Dimensions D1 and E do not include mold protrusion. Allowable
protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side.
3. Lead coplanarity is 0.10 mm maximum.
14.00
12.40
8.00
D1
E
12.50 Note 2
8.10
0.70
Note 2
L
0.60
L1
b
0.25 BASIC
0.22
0.17
0.10
0.27
0.21
c
–
e
0.50 BASIC
10/18/01
DRAWING NO. REV.
32V
TITLE
2325 Orchard Parkway
San Jose, CA 95131
32V, 32-lead (8 x 14 mm Package) Plastic Thin Small Outline
Package, Type I (VSOP)
B
R
14
AT27BV020
0902F–EPROM–12/07
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Atmel Europe
Le Krebs
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-en-
Yvelines Cedex
France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Product Contact
Web Site
Technical Support
Sales Contact
www.atmel.com
eprom@atmel.com
www.atmel.com/contacts
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2007 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, and others are registered trademarks or trademarks of
Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
0902F–EPROM–12/07
相关型号:
©2020 ICPDF网 联系我们和版权申明