AT24C32 [ATMEL]
2-Wire Serial EEPROM; 2线串行EEPROM型号: | AT24C32 |
厂家: | ATMEL |
描述: | 2-Wire Serial EEPROM |
文件: | 总15页 (文件大小:240K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Features
• Low-Voltage and Standard-Voltage Operation
– 5.0 (VCC = 4.5V to 5.5V)
– 2.7 (VCC = 2.7V to 5.5V)
– 2.5 (VCC = 2.5V to 5.5V)
– 1.8 (VCC = 1.8V to 5.5V)
• Low-Power Devices (ISB = 2 µA @ 5.5V) Available
• Internally Organized 4096 x 8, 8192 x 8
• 2-Wire Serial Interface
• Schmitt Trigger, Filtered Inputs for Noise Suppression
• Bidirectional Data Transfer Protocol
• 100 kHz (1.8V, 2.5V, 2.7V) and 400 kHz (5V) Compatibility
• Write Protect Pin for Hardware Data Protection
• 32-Byte Page Write Mode (Partial Page Writes Allowed)
• Self-Timed Write Cycle (10 ms max)
• High Reliability
2-Wire
Serial EEPROM
32K (4096 x 8)
64K (8192 x 8)
– Endurance: 1 Million Write Cycles
– Data Retention: 100 Years
– ESD Protection: >3,000V
• Automotive Grade and Extended Temperature Devices Available
• 8-Pin JEDEC PDIP, 8-Pin and 14-Pin JEDEC SOIC, 8-Pin EIAJ SOIC,
and 8-pin TSSOP Packages
AT24C32
AT24C64
Description
The AT24C32/64 provides 32,768/65,536 bits of serial electrically erasable and pro-
grammable read only memory (EEPROM) organized as 4096/8192 words of 8 bits
each. The device’s cascadable feature allows up to 8 devices to share a common 2-
wire bus. The device is optimized for use in many industrial and commercial applica-
tions where low power and low voltage operation are essential. The AT24C32/64 is
available in space saving 8-pin JEDEC PDIP, 8-pin and 14-pin JEDEC SOIC, 8-pin
EIAJ SOIC, and 8-pin TSSOP packages and is accessed via a 2-wire serial interface.
In addition, the entire family is available in 5.0V (4.5V to 5.5V), 2.7V (2.7V to 5.5V),
2.5V (2.5V to 5.5V) and 1.8V (1.8V to 5.5V) versions.
8-Pin PDIP
Pin Configurations
A0
A1
1
2
3
4
8
7
6
5
VCC
WP
Pin Name
A0 to A2
SDA
Function
2-Wire, 32K
Address Inputs
Serial Data
A2
SCL
SDA
Serial E2PROM
GND
SCL
Serial Clock Input
Write Protect
8-Pin TSSOP
WP
A0
A1
A2
1
2
3
4
8
7
6
5
VCC
WP
SCL
SDA
14-Pin SOIC
GND
NC
A0
1
14
13
NC
2
VCC
WP
NC
8-Pin SOIC
A1
3
4
5
6
7
12
11
10
9
NC
A2
A0
A1
1
2
3
4
8
7
6
5
VCC
WP
SCL
SDA
NC
GND
NC
A2
SCL
SDA
8
GND
Rev. 0336F–08/98
Absolute Maximum Ratings*
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Operating Temperature.................................. -55°C to +125°C
Storage Temperature..................................... -65°C to +150°C
Voltage on Any Pin
with Respect to Ground.....................................-1.0V to +7.0V
Maximum Operating Voltage........................................... 6.25V
DC Output Current........................................................ 5.0 mA
Block Diagram
Device Addressing section). When the pins are not hard-
wired, the default A2, A1, and A0 are zero.
Pin Description
SERIAL CLOCK (SCL): The SCL input is used to positive
edge clock data into each EEPROM device and negative
edge clock data out of each device.
WRITE PROTECT (WP): The write protect input, when tied
to GND, allows normal write operations. When WP is tied
high to VCC, all write operations to the upper quandrant
(8/16K bits) of memory are inhibited. If left unconnected,
WP is internally pulled down to GND.
SERIAL DATA (SDA): The SDA pin is bidirectional for
serial data transfer. This pin is open-drain driven and may
be wire-ORed with any number of other open-drain or open
collector devices.
Memory Organization
DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1
and A0 pins are device address inputs that are hard wired
or left not connected for hardware compatibility with
AT24C16. When the pins are hardwired, as many as eight
32K/64K devices may be addressed on a single bus sys-
tem (device addressing is discussed in detail under the
AT24C32/64, 32K/64K SERIAL EEPROM: The 32K/64K is
internally organized as 256 pages of 32 bytes each. Ran-
dom word addressing requires a 12/13 bit data word
address.
AT24C32/64
2
AT24C32/64
Pin Capacitance(1)
Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V.
Symbol
CI/O
Test Condition
Max
8
Units
pF
Conditions
VI/O = 0V
VIN = 0V
Input/Output Capacitance (SDA)
Input Capacitance (A0, A1, A2, SCL)
CIN
6
pF
Note:
1. This parameter is characterized and is not 100% tested.
DC Characteristics
Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = +1.8V to +5.5V, TAC = 0°C to +70°C,
VCC = +1.8V to +5.5V (unless otherwise noted).
Symbol
VCC1
VCC2
VCC3
VCC4
ICC1
Parameter
Test Condition
Min
1.8
2.5
2.7
4.5
Typ
Max
5.5
5.5
5.5
5.5
1.0
3.0
0.1
2.0
0.5
2.0
0.5
2.0
Units
V
Supply Voltage
Supply Voltage
V
Supply Voltage
V
Supply Voltage
V
Supply Current VCC = 5.0V
Supply Current VCC = 5.0V
READ at 100 kHz
WRITE at 100 kHz
0.4
2.0
mA
mA
µA
ICC2
VCC = 1.8V
Standby Current
(1.8V option)
ISB1
VIN = VCC or VSS
VIN = VCC or VSS
V
CC = 5.5V
CC = 2.5V
V
µA
µA
Standby Current
(2.5V option)
ISB2
VCC = 5.5V
VCC = 2.7V
Standby Current
(2.7V option)
ISB3
VIN = VCC or VSS
VIN = VCC or VSS
VCC = 5.5V
Standby Current
(5V option)
ISB4
VCC = 4.5 - 5.5V
20
35
µA
ILI
Input Leakage Current
Output Leakage Current
Input Low Level(1)
VIN = VCC or VSS
0.10
0.05
3.0
3.0
µA
µA
V
ILO
VOUT = VCC or VSS
VIL
-0.6
VCC x 0.3
VCC + 0.5
0.4
VIH
VOL2
VOL1
Input High Level(1)
VCC x 0.7
V
Output Low Level VCC = 3.0V
Output Low Level VCC = 1.8V
IOL = 2.1 mA
V
IOL = 0.15 mA
0.2
V
Notes: 1. VIL min and VIH max are reference only and are not tested.
3
AC Characteristics
Applicable over recommended operating range from TA = -40°C to +85°C, VCC = +1.8V to +5.5V, CL = 1 TTL Gate and 100
pF (unless otherwise noted).
1.8-volt
2.7-, 2.5-volt
5.0-volt
Symbol
fSCL
Parameter
Min
Max
Min
Max
Min
Max
Units
kHz
µs
Clock Frequency, SCL
Clock Pulse Width Low
Clock Pulse Width High
Noise Suppression Time(1)
Clock Low to Data Out Valid
100
100
400
tLOW
tHIGH
tI
4.7
4.0
4.7
4.0
1.2
0.6
µs
100
4.5
100
4.5
50
ns
tAA
0.1
4.7
0.1
4.7
0.1
1.2
0.9
µs
Time the bus must be free
tBUF
µs
before a new transmission can start(1)
tHD.STA
tSU.STA
tHD.DAT
tSU.DAT
tR
Start Hold Time
4.0
4.7
0
4.0
4.7
0
0.6
0.6
0
µs
Start Set-up Time
Data In Hold Time
Data In Set-up Time
Inputs Rise Time(1)
Inputs Fall Time(1)
Stop Set-up Time
Data Out Hold Time
Write Cycle Time
5.0V, 25°C, Page Mode
µs
µs
200
200
100
ns
1.0
1.0
0.3
µs
tF
300
300
300
ns
tSU.STO
tDH
4.7
4.7
0.6
50
µs
ns
100
100
tWR
20
10
10
ms
Endurance(1)
1M
1M
1M
Write Cycles
Note:
1. This parameter is characterized and is not 100% tested.
Device Operation
CLOCK and DATA TRANSITIONS: The SDA pin is nor-
mally pulled high with an external device. Data on the SDA
pin may change only during SCL low time periods (refer to
Data Validity timing diagram). Data changes during SCL
high periods will indicate a start or stop condition as
defined below.
ACKNOWLEDGE: All addresses and data words are seri-
ally transmitted to and from the EEPROM in 8-bit words.
The EEPROM sends a zero during the ninth clock cycle to
acknowledge that it has received each word.
STANDBY MODE: The AT24C32/64 features a low power
standby mode which is enabled: a) upon power-up and b)
after the receipt of the STOP bit and the completion of any
internal operations.
START CONDITION: A high-to-low transition of SDA with
SCL high is a start condition which must precede any other
command (refer to Start and Stop Definition timing dia-
gram).
MEMORY RESET: After an interruption in protocol, power
loss or system reset, any 2-wire part can be reset by follow-
ing these steps:
STOP CONDITION: A low-to-high transition of SDA with
SCL high is a stop condition. After a read sequence, the
stop command will place the EEPROM in a standby power
mode (refer to Start and Stop Definition timing diagram).
(a) Clock up to 9 cycles, (b) look for SDA high in each cycle
while SCL is high and then (c) create a start condition as
SDA is high.
AT24C32/64
4
AT24C32/64
Bus Timing
SCL: Serial Clock, SDA: Serial Data I/O
Write Cycle Timing
SCL: Serial Clock, SDA: Serial Data I/O
(1)
WR
t
Note:
1. The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal clear/write
cycle.
5
Data Validity
Start and Stop Definition
Output Acknowledge
AT24C32/64
6
AT24C32/64
The data word address lower 5 bits are internally incre-
mented following the receipt of each data word. The higher
data word address bits are not incremented, retaining the
memory page row location. When the word address, inter-
nally generated, reaches the page boundary, the following
byte is placed at the beginning of the same page. If more
than 32 data words are transmitted to the EEPROM, the
data word address will “roll over” and previous data will be
overwritten.
Device Addressing
The 32K/64K EEPROM requires an 8-bit device address
word following a start condition to enable the chip for a read
or write operation (refer to Figure 1). The device address
word consists of a mandatory one, zero sequence for the
first four most significant bits as shown. This is common to
all 2-wire EEPROM devices.
The 32K/64K uses the three device address bits A2, A1, A0
to allow as many as eight devices on the same bus. These
bits must compare to their corresponding hardwired input
pins. The A2, A1, and A0 pins use an internal proprietary
circuit that biases them to a logic low condition if the pins
are allowed to float.
ACKNOWLEDGE POLLING: Once the internally-timed
write cycle has started and the EEPROM inputs are dis-
abled, acknowledge polling can be initiated. This involves
sending a start condition followed by the device address
word. The read/write bit is representative of the operation
desired. Only if the internal write cycle has completed will
the EEPROM respond with a zero, allowing the read or
write sequence to continue.
The eighth bit of the device address is the read/write opera-
tion select bit. A read operation is initiated if this bit is high
and a write operation is initiated if this bit is low.
Upon a compare of the device address, the EEPROM will
output a zero. If a compare is not made, the device will
return to standby state.
Read Operations
Read operations are initiated the same way as write opera-
tions with the exception that the read/write select bit in the
device address word is set to one. There are three read
operations: current address read, random address read
and sequential read.
NOISE PROTECTION: Special internal circuitry placed on
the SDA and SCL pins prevent small noise spikes from
activating the device. A low-VCC detector (5-volt option)
resets the device to prevent data corruption in a noisy envi-
ronment.
CURRENT ADDRESS READ: The internal data word
address counter maintains the last address accessed dur-
ing the last read or write operation, incremented by one.
This address stays valid between operations as long as the
chip power is maintained. The address “roll over” during
read is from the last byte of the last memory page, to the
first byte of the first page. The address “roll over” during
write is from the last byte of the current page to the first
byte of the same page.
DATA SECURITY: The AT24C32/64 has a hardware data
protection scheme that allows the user to write protect the
upper quadrant (8/16K bits) of memory when the WP pin is
at VCC
.
Write Operations
BYTE WRITE: A write operation requires two 8-bit data
word addresses following the device address word and
acknowledgment. Upon receipt of this address, the
EEPROM will again respond with a zero and then clock in
the first 8-bit data word. Following receipt of the 8-bit data
word, the EEPROM will output a zero and the addressing
device, such as a microcontroller, must terminate the write
sequence with a stop condition. At this time the EEPROM
enters an internally-timed write cycle, tWR, to the nonvolatile
memory. All inputs are disabled during this write cycle and
the EEPROM will not respond until the write is complete
(refer to Figure 2).
Once the device address with the read/write select bit set
to one is clocked in and acknowledged by the EEPROM,
the current address data word is serially clocked out. The
microcontroller does not respond with an input zero but
does generate a following stop condition (refer to Figure 4).
RANDOM READ: A random read requires a “dummy” byte
write sequence to load in the data word address. Once the
device address word and data word address are clocked in
and acknowledged by the EEPROM, the microcontroller
must generate another start condition. The microcontroller
now initiates a current address read by sending a device
address with the read/write select bit high. The EEPROM
acknowledges the device address and serially clocks out
the data word. The microcontroller does not respond with a
zero but does generate a following stop condition (refer to
Figure 5).
PAGE WRITE: The 32K/64K EEPROM is capable of 32-
byte page writes.
A page write is initiated the same way as a byte write, but
the microcontroller does not send a stop condition after the
first data word is clocked in. Instead, after the EEPROM
acknowledges receipt of the first data word, the microcon-
troller can transmit up to 31 more data words. The
EEPROM will respond with a zero after each data word
received. The microcontroller must terminate the page
write sequence with a stop condition (refer to Figure 3).
SEQUENTIAL READ: Sequential reads are initiated by
either a current address read or a random address read.
After the microcontroller receives a data word, it responds
with an acknowledge. As long as the EEPROM receives an
7
acknowledge, it will continue to increment the data word
address and serially clock out sequential data words. When
the memory address limit is reached, the data word
address will “roll over” and the sequential read will con-
tinue. The sequential read operation is terminated when
the microcontroller does not respond with a zero but does
generate a following stop condition (refer to Figure 6).
Figure 1. Device Address
Figure 2. Byte Write
Figure 3. Page Write
Notes: 1. * = DON’T CARE bits
2. † = DON’T CARE bits for the 32K
Figure 4. Current Address Read
Figure 5. Random Read
Note:
1. * = DON’T CARE bits
AT24C32/64
8
AT24C32/64
Figure 6. Sequential Read
9
AT24C32 Ordering Information
tWR (max)
(ms)
ICC (max)
ISB (max)
fMAX
(kHz)
(µA)
(µA)
Ordering Code
Package
Operation Range
10
3000
3000
1500
1500
35
400
400
100
100
AT24C32-10PC
AT24C32N-10SC
AT24C32W-10SC
AT24C32-10TC
AT24C32-10SC
8P3
8S1
8S2
8T
Commercial
(0°C to 70°C)
14S
35
AT24C32-10PI
AT24C32N-10SI
AT24C32W-10SI
AT24C32-10TI
AT24C32-10SI
8P3
8S1
8S2
8T
Industrial
(-40°C to 85°C)
14S
10
0.5
0.5
AT24C32-10PC-2.7
AT24C32N-10SC-2.7
AT24C32W-10SC-2.7
AT24C32-10TC-2.7
AT24C32-10SC-2.7
8P3
8S1
8S2
8T
Commercial
(0°C to 70°C)
14S
AT24C32-10PI-2.7
AT24C32N-10SI-2.7
AT24C32W-10SI-2.7
AT24C32-10TI-2.7
AT24C32-10SI-2.7
8P3
8S1
8S2
8T
Industrial
(-40°C to 85°C)
14S
Package Type
8P3
8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8-Lead, 0.200" Wide, Plastic Gull Wing Small Outline (EIAJ SOIC)
8-Lead, 0.170" Wide, Plastic Gull Wing Small Outline (TSSOP)
14-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (SOIC)
Options
8S1
8S2
8T
14S
Blank
-2.7
Standard Operation (4.5V to 5.5V)
Low Voltage (2.7V to 5.5V)
-2.5
Low Voltage (2.5V to 5.5V)
-1.8
Low Voltage (1.8V to 5.5V)
AT24C32/64
10
AT24C32/64
AT24C32 Ordering Information (Continued)
tWR (max)
(ms)
ICC (max)
ISB (max)
(µA)
fMAX
(kHz)
(µA)
Ordering Code
Package
Operation Range
10
1000
1000
800
0.5
0.5
0.1
0.1
100
100
100
100
AT24C32-10PC-2.5
AT24C32N-10SC-2.5
AT24C32W-10SC-2.5
AT24C32-10TC-2.5
AT24C32-10SC-2.5
8P3
8S1
8S2
8T
Commercial
(0°C to 70°C)
14S
AT24C32-10PI-2.5
AT24C32N-10SI-2.5
AT24C32W-10SI-2.5
AT24C32-10TI-2.5
AT24C32-10SI-2.5
8P3
8S1
8S2
8T
Industrial
(-40°C to 85°C)
14S
10
AT24C32-10PC-1.8
AT24C32N-10SC-1.8
AT24C32W-10SC-1.8
AT24C32-10TC-1.8
AT24C32-10SC-1.8
8P3
8S1
8S2
8T
Commercial
(0°C to 70°C)
14S
800
AT24C32-10PI-1.8
AT24C32N-10SI-1.8
AT24C32W-10SI-1.8
AT24C32-10TI-1.8
AT24C32-10SI-1.8
8P3
8S1
8S2
8T
Industrial
(-40°C to 85°C)
14S
Package Type
8P3
8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8-Lead, 0.200" Wide, Plastic Gull Wing Small Outline (EIAJ SOIC)
8-Lead, 0.170" Wide, Plastic Gull Wing Small Outline (TSSOP)
14-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (SOIC)
Options
8S1
8S2
8T
14S
Blank
-2.7
Standard Operation (4.5V to 5.5V)
Low Voltage (2.7V to 5.5V)
-2.5
Low Voltage (2.5V to 5.5V)
-1.8
Low Voltage (1.8V to 5.5V)
11
AT24C64 Ordering Information
tWR (max)
(ms)
ICC (max)
ISB (max)
fMAX
(kHz)
(µA)
(µA)
Ordering Code
Package
Operation Range
10
3000
3000
1500
1500
35
400
400
100
100
AT24C64-10PC
AT24C64N-10SC
AT24C64W-10SC
AT24C64-10TC
AT24C64-10SC
8P3
8S1
8S2
8T
Commercial
(0°C to 70°C)
14S
35
AT24C64-10PI
AT24C64N-10SI
AT24C64W-10SI
AT24C64-10TI
AT24C64-10SI
8P3
8S1
8S2
8T
Industrial
(-40°C to 85°C)
14S
10
0.5
0.5
AT24C64-10PC-2.7
AT24C64N-10SC-2.7
AT24C64W-10SC-2.7
AT24C64-10TC-2.7
AT24C64-10SC-2.7
8P3
8S1
8S2
8T
Commercial
(0°C to 70°C)
14S
AT24C64-10PI-2.7
AT24C64N-10SI-2.7
AT24C64W-10SI-2.7
AT24C64-10TI-2.7
AT24C64-10SI-2.7
8P3
8S1
8S2
8T
Industrial
(-40°C to 85°C)
14S
Package Type
8P3
8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8-Lead, 0.200" Wide, Plastic Gull Wing Small Outline (EIAJ SOIC)
8-Lead, 0.170" Wide, Plastic Gull Wing Small Outline (TSSOP)
14-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (SOIC)
Options
8S1
8S2
8T
14S
Blank
-2.7
Standard Operation (4.5V to 5.5V)
Low Voltage (2.7V to 5.5V)
-2.5
Low Voltage (2.5V to 5.5V)
-1.8
Low Voltage (1.8V to 5.5V)
AT24C32/64
12
AT24C32/64
AT24C64 Ordering Information (Continued)
tWR (max)
(ms)
ICC (max)
ISB (max)
fMAX
(kHz)
(µA)
(µA)
Ordering Code
Package
Operation Range
10
1000
1000
800
0.5
0.5
0.1
0.1
100
100
100
100
AT24C64-10PC-2.5
AT24C64N-10SC-2.5
AT24C64W-10SC-2.5
AT24C64-10TC-2.5
AT24C64-10SC-2.5
8P3
8S1
8S2
8T
Commercial
(0°C to 70°C)
14S
AT24C64-10PI-2.5
AT24C64N-10SI-2.5
AT24C64W-10SI-2.5
AT24C64-10TI-2.5
AT24C64-10SI-2.5
8P3
8S1
8S2
8T
Industrial
(-40°C to 85°C)
14S
10
AT24C64-10PC-1.8
AT24C64N-10SC-1.8
AT24C64W-10SC-1.8
AT24C64-10TC-1.8
AT24C64-10SC-1.8
8P3
8S1
8S2
8T
Commercial
(0°C to 70°C)
14S
800
AT24C64-10PI-1.8
AT24C64N-10SI-1.8
AT24C64W-10SI-1.8
AT24C64-10TI-1.8
AT24C64-10SI-1.8
8P3
8S1
8S2
8T
Industrial
(-40°C to 85°C)
14S
Package Type
8P3
8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8-Lead, 0.200" Wide, Plastic Gull Wing Small Outline (EIAJ SOIC)
8-Lead, 0.170" Wide, Plastic Gull Wing Small Outline (TSSOP)
14-Lead, 0.150" Wide, Plastic Gull Wing Small Outline (SOIC)
Options
8S1
8S2
8T
14S
Blank
-2.7
Standard Operation (4.5V to 5.5V)
Low Voltage (2.7V to 5.5V)
-2.5
Low Voltage (2.5V to 5.5V)
-1.8
Low Voltage (1.8V to 5.5V)
13
Packaging Information
8P3, 8-Lead, 0.300" Wide, Plastic Dual Inline
Package (PDIP)
8S1, 8-Lead, 0150" Wide, Plastic Gull Wing Small
Outline (JEDEC SOIC)
Dimensions in Inches and (Millimeters)
JEDEC STANDARD MS-001 BA
Dimensions in Inches and (Millimeters)
.400 (10.16)
.355 (9.02)
.020 (.508)
.013 (.330)
PIN
1
.244 (6.20)
.228 (5.79)
.157 (3.99)
.150 (3.81)
.280 (7.11)
.240 (6.10)
PIN 1
.037 (.940)
.027 (.690)
.300 (7.62) REF
.210 (5.33) MAX
.050 (1.27) BSC
.100 (2.54) BSC
.196 (4.98)
.189 (4.80)
SEATING
PLANE
.068 (1.73)
.053 (1.35)
.015 (.380) MIN
.150 (3.81)
.115 (2.92)
.022 (.559)
.014 (.356)
.070 (1.78)
.045 (1.14)
.010 (.254)
.004 (.102)
.325 (8.26)
.300 (7.62)
0
8
REF
.010 (.254)
.007 (.203)
0
REF
15
.012 (.305)
.008 (.203)
.050 (1.27)
.016 (.406)
.430 (10.9) MAX
8S2, 8-Lead, 0.200" Wide, Plastic Gull Wing Small
Outline (EIAJ SOIC)
8T, 8-Lead, Plastic Thin Small Outline Package
(TSSOP)
Dimensions in Inches and (Millimeters)
Dimensions in Millimeters and (Inches)*
PIN 1
.020 (.508)
.012 (.305)
6.50 (.256)
6.25 (.246)
.213 (5.41) .330 (8.38)
.205 (5.21) .300 (7.62)
PIN 1
0.30 (.012)
0.19 (.008)
.050 (1.27) BSC
3.10 (.122)
2.90 (.114)
.212 (5.38)
.203 (5.16)
.080 (2.03)
.070 (1.78)
1.05 (.041)
0.80 (.033)
1.20 (.047) MAX
.65 (.026) BSC
0.15 (.006)
0.05 (.002)
.013 (.330)
.004 (.102)
4.5 (.177)
4.3 (.169)
0.20 (.008)
0.09 (.004)
0
8
REF
.010 (.254)
.007 (.178)
0.75 (.030)
0.45 (.018)
0
8
REF
.035 (.889)
.020 (.508)
*Controlling dimension: millimeters
AT24C32/64
14
AT24C32/64
Packaging Information
14S, 14-Lead, 0.150" Wide, Plastic Gull Wing Small
Outline (SOIC)
Dimensions in Inches and (Millimeters)
.020 (.508)
.013 (.330)
.158 (4.01)
.152 (3.86)
.244 (6.20)
.228 (5.79)
PIN 1
.050 (1.27) BSC
.344 (8.74)
.337 (8.56)
.068 (1.73)
.053 (1.35)
.010 (.249)
.004 (.102)
0
8
REF
.010 (.249)
.008 (.191)
.050 (1.27)
.016 (.406)
15
相关型号:
©2020 ICPDF网 联系我们和版权申明