EXB100-48S1V8 [ARTESYN]
54-100W DC/DC Isolated Converters; 54-100W DC / DC隔离转换器
| 型号： | EXB100-48S1V8 |
| 厂家： | 
ARTESYN TECHNOLOGIES |
| 描述： | 54-100W DC/DC Isolated Converters |
| 文件： | 总2页 (文件大小：59K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
EXB100 Series
S i n g l e o u t p u t
DC/DC CONVERTERS 54-100W DC/DC Isolated Converters
1
NEW Product
• Ultra wide trim range, 60% to 110% (1.08V to 5.5V)
• High efficiency, 91.5% @ 5V, 90.5% @ 3.3V, 87.5% @ 1.8V
• Basic insulation (input to output)
• Industry standard half-brick pin-out
• No minimum load
• Over-voltage and over-temperature protection
• Remote ON/OFF
The EXB100 series of 100W single output isolated DC/DC converters are specially
designed to meet the power needs of low voltage silicon. Housed in an open-frame
package with standard footprint, these latest generation converters offer efficiencies as
high as 91.5% (typical on 5V at 20A). The series comprises three 48V input models with
5V, 3.3V and 1.8V outputs. All models feature a wide input range, trimmable output
voltage and 30A output (5V is limited to 20A). Remote sense and remote ON/OFF
facilities are included as standard, and the converters are comprehensively protected
against over-current, over-voltage and over-temperature conditions.
TÜV
2 YEAR WARRANTY
All specifications are typical at nominal input, full load at 25°C unless otherwise stated
SPECIFICATIONS
OUTPUT SPECIFICATIONS
Voltage adjustability
EMC CHARACTERISTICS
60% to 110%
1.5%
Conducted emissions
Radiated emissions
EN55022 (See Note 7)
EN55022 (See Note 7)
EN55022
Level A
Level B
Level A
Output setpoint accuracy
(See Long Form Data Sheet)
Line regulation
Load regulation
Total error band
Minimum load
Overshoot
Low line to high line
±0.2% max.
±0.4% max.
3.0%
Immunity:
ESD air
ESD contact
Full load to min. load
EN61000-4-2 8kV, 15kV
EN61000-4-2 6kV, 8kV
Radiated field enclosure EN61000-4-3 10V/m
Conducted (DC power) EN61000-4-6 10V
0%
Conducted (signal)
Input transients
EN61000-4-6 10V
(See Note 5)
At turn-on and turn-off
None
ETS 300 132-2, ETR 283
Undershoot
None
GENERAL SPECIFICATIONS
Ripple and noise
5Hz to 20MHz
(See Note 1)
Deviation
100mV pk-pk
50mV rms
Efficiency
See table
1500VDC
Basic insulation
Input/output
Transient response
(See Note 2)
150mV
300µs recovery to
Switching frequency
(Fixed)
5V
3.3V, 1.8V
300kHz typ.
220kHz typ.
within total error band
Approvals and
standards (See Note 8)
TÜV Product Service
UL/cUL60950
INPUT SPECIFICATIONS
Input voltage range
Input current
36 to 75VDC
Material flammability
Weight
UL94V-0
45g (1.59oz)
115,000 hours
No load
150mA
20mA
Remote OFF
MTBF
Representative model:
MIL-HDBK-217F
1V8 @ 48Vin, 40ºC
Input current (max.)
Input reflected ripple
(See Note 3)
3.15A max. @ Io max.
and Vin = 36 to 75V
100% load, ground benign
BELLCORE 332
(See Note 4)
60mA (pk-pk)
591,000 hours
-40°C to +90°C
Remote ON/OFF
(See Note 5)
Open collector ref to -input
>2VDC
ENVIRONMENTAL SPECIFICATIONS
Logic compatibility
ON
OFF
Thermal performance
Operating ambient.
<1.2VDC
temperature
Non-operating
3,000m
-40°C to +125°C
Under-voltage lockout
Power up
Power down
36V
30V
Altitude derating
(above sea level)
20%
50%
10,000m
Start-up time
(See Note 6)
Power up
Remote ON/OFF
40ms
35ms
File Name: EXB100S.PDF Rev: 29 March 2002
EXB100 Series
S i n g l e o u t p u t
DC/DC CONVERTERS 54-100W DC/DC Isolated Converters
2
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
NEW Product
OUTPUT
POWER
(MAX.)
OUTPUT
OUTPUT
REGULATION
INPUT
OUTPUT
VOLTAGE
EFFICIENCY
(TYP.)
MODEL
OVP
CURRENT CURRENT
(9)
VOLTAGE
NUMBER
LINE
LOAD
(MIN.)
0A
(MAX.)
20A
100W
100W
54W
36-75VDC
36-75VDC
36-75VDC
6.0VDC
3.9VDC
2.2VDC
5.0V
3.3V
1.8V
91.5%
90.5%
87.5%
±0.2%
±0.2%
±0.2%
±0.4%
±0.4%
±0.4%
EXB100-48S05
EXB100-48S3V3
EXB100-48S1V8
0A
30A
0A
30A
Notes
PROTECTION
1
2
Measured as per recommended set-up. See Application Note 129 for details.
di/dt = 0.1A/µs, Vin = 48VDC, Tc = 25°C, load change = 0.5 lo max. to 0.75
lo max. and 0.75 lo max. to 0.5 lo max.
Recommended input fusing is a 5A HRC 200V rated fuse.
Measured with external filter. See Application Note 129 for details.
Signal line assumed <3m in length.
Start-up into resistive load.
The EXB100 meets levels A and B conducted emissions with external
components. See Application Note 129 for details.
Short circuit protection
Overvoltage protection
Continuous
Non-latching clamp
3
4
5
6
7
TELECOM SPECIFICATION
Central office interface A
ETS300-132-2 input voltage
and current requirements
8
9
This product is only for inclusion by professional installers within other
equipment and must not be operated as a stand alone product.
Negative remote ON/OFF option also available. Add suffix ‘-R’ to part
number, for example EXB100-48S3V3-R.
CAUTION: Hazardous internal voltages and high temperatures.
Ensure that unit is not user accessible.
PIN CONNECTIONS
Max open-frame
converter height
PIN NUMBER
FUNCTION
-Vin
1
2
3
4
5
6
7
8
9
seating plane
No Pin
Ø0.040 ±0.002
(Ø1.02 ±0.05)
6 Places
Remote ON/OFF
+Vin
Ø0.080 ±0.002
(Ø2.03 ±0.05)
Minimum clearance from
2 Places
seating plane to
underside components
+Vout
All dimensions in inches (mm)
General tolerance ±0.01in (±0.25mm)
except where specified otherwise
+Sense
Trim
2.280±0.02
(57.91±0.5)
-Sense
-Vout
Vin-
Vo-
Sense-
Trim
Sense+
Vo+
Remote
ON/OFF
Vin+
Bottom View
1.900
(48.26)
International Safety Standard Approvals
UL/cUL CAN/CSA 22.2 No. 60950-00 : UL 60950
File No. E174104
TÜV
TÜV Product Service. Certificate No. B 02 02 38572 031
Data Sheet © Artesyn Technologies
® 2002
The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising
from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein.
Please consult our website for the following items: ✔ Application Note ✔ Longform Data Sheet
www.a rte s yn.com
File Name: EXB100S.PDF Rev: 29 March 2002
相关型号：
©2020 ICPDF网 联系我们和版权申明