APL111733GC-TRL [ANPEC]
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V; 1A低压降快速响应正可调稳压器和固定1.2V ， 1.8V ， 2.5V ， 2.85V ， 3.3V和5V
| 型号： | APL111733GC-TRL |
| 厂家： | 
ANPEC ELECTRONICS COROPRATION |
| 描述： | 1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V |
| 文件： | 总19页 (文件大小：299K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
APL1117
1A Low Dropout Fast Response Positive Adjustable Regulator and
Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
Features
General Description
The APL1117 is a low dropout three-terminal adjustable
regulators with 1A output current capability. In order to
obtain lower dropout voltage and faster transient
·
·
·
·
·
·
·
·
·
·
Guaranteed Output Voltage Accuracy within 2%
Fast Transient Response
Guaranteed Dropout Voltage at Multiple Currents
Load Regulation : 0.1% Typ.
response, which is critical for low voltage applications,
the APL1117 has been optimized. The device is available
in an adjustable version and fixed output voltages of 1.2V,
1.8V, 2.5V, 2.85V, 3.3V, and 5V. The output available volt-
age range of an adjustable version is from 1.25 to 10.7V
with an input supply below 12V. Dropout voltage is guar-
anteed at a maximum of 1.3V at 1A. Current limit is
trimmed to ensure specified output current and controlled
short-circuit current. On-chip thermal limiting provides
protection against any combination of overload that would
create excessive junction temperatures. The APL1117 is
available in the industry standard 3-pin TO-220, TO-252-
3, TO-263-3, and the low profile surface mount SOT-223
power packages which can be used in applications where
space is limited.
Line Regulation : 0.03% Typ.
Low Dropout Voltage : 1.1V Typ. at IOUT =1A
Current-Limit : 1A Typ. at TJ=25°C
On-Chip Thermal Limiting : 150°C Typ.
Adjustable Output : 1.25~10.7V
Standard 3-pin TO-220, TO-252-3, TO-263-3 and
SOT-223 Power Packages
·
Lead Free and Green Devices Available
(RoHS Compliant)
Applications
·
·
·
Active SCSI Terminators
Low Voltage Logic Supplies
Post Regulator for Switching Power Supply
Simplified Application Circuits
1.25V to 10.7V Adjustable Regulator
Improving Ripple Rejection
APL1117
APL1117
VIN
VOUT1
IN
OUT
VIN
IN
OUT
ADJ
VOUT
R1
ADJ
R1
121W
1%
+
121W
10mF
150mF
100m F
C2
+
+
10m F
R2
365W
C1
10mF
C1*
R2
1k
+
1%
* Needed if device is far from filter capacitors
R1 + R2
* C1 improves ripple rejection.
XC should be approximately
equal to R1 at ripple frequency
VOUT = 1.250V X
R1
5V Regulator with Shutdown
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and
advise customers to obtain the latest version of relevant information to verify before placing orders.
Copyright ã ANPEC Electronics Corp.
1
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Ordering and Marking Information
Package Code
APL1117
F : TO-220 G : TO-263-3 U : TO-252-3 V : SOT-223
Operating Ambient Temperature Range
C : 0 to 70 oC
Assembly Material
Handling Code
Handling Code
TU : Tube
Voltage Code
12 : 1.2V
33 : 3.3V
Assembly Material
TR : Tape & Reel
Temperature Range
Package Code
Voltage Code
18 : 1.8V
50 : 5V
25 : 2.5V
Blank : Adjustable Version
28 : 2.85V
L : Lead Free Device
G : Halogen and Lead Free Device
VV
APL1117 F/G/U:
APL1117 V:
XXXXX - Date Code ; VV-Voltage Code
APL1117
XXXXX
APL1117
XXXXX
APL1117
XXXXX
APL1117
XXXXXVV
XXXXX - Date Code ; VV-Voltage Code
Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which
are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020D for
MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen
free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by
weight).
Pin Configuration
Front View for TO-220
Front View for TO-263-3
3
2
1
VIN
3
2
1
VIN
VOUT
ADJ/GND
VOUT
ADJ/GND
TAB IS VOUT
Front View for TO-252-3
Front View for SOT-223
VIN
3
3
2
1
VIN
2
1
VOUT
TAB IS VOUT
TAB IS VOUT
VOUT
ADJ/GND
ADJ/GND
Copyright ã ANPEC Electronics Corp.
2
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Absolute Maximum Ratings (Note 1)
Symbol
Parameter
Rating
Unit
Input Voltage
APL1117, APL1117-33
APL1117-50
APL1117-12, APL1117-18, APL1117-25, APL1117-28
15
13
9
VIN
V
TJ
Junction Temperature Range
Storage Temperature Range
0 to 150
-65 to +150
260
°C
°C
°C
TSTG
TSDR
Maximum Lead Soldering Temperature, 10 Seconds
Note 1: The values here show the absolute maximum rating, and for normal usage please refer the test condition in Electrical
Characteristics Table.
Recommended Operating Conditions
Symbol
Parameter
Range
0 ~ 70
Unit
oC
oC
TA
TJ
Ambient Temperature
Junction Temperature
0 ~ 125
Electrical Characteristics
Unless otherwise noted, these specifications apply over CIN = 10mF , COUT = 10mF, and TA = 0 to 70°C. Typical values
refer to TA = 25°C.
APL1117
Symbol
Parameter
Test Conditions
Unit
Min.
Typ.
Max.
10mA£ IOUT £1A, 1.4V£(VIN -VOUT) £10.75V,
TJ = 0~125°C
VREF
Reference Voltage
Output Voltage
1.225
1.250
1.275
V
APL1117-12 TJ = 0~125°C,
1.176
1.764
2.450
2.790
3.235
4.900
1.200
1.800
2.500
2.850
3.300
5.000
1.224
1.836
2.550
2.910
3.365
5.100
0£ IOUT £ 1A, 2.65V£ VIN £9V
TJ = 0~125°C,
0£ IOUT £ 1A, 3.25V£ VIN £9V
APL1117-18
TJ = 0~125°C,
0£ IOUT £ 1A, 3.95V£ VIN £9V
APL1117-25
APL1117-28
APL1117-33
VOUT
V
TJ = 0~125°C,
0£ IOUT £1A, 4.25V£ VIN £9V
TJ = 0~125°C,
0£ IOUT £ 1A, 4.75V£ VIN £12V
APL1117-50 TJ = 0~125°C,
0£ IOUT £ 1A, 6.45V£ VIN £12V
Line Regulation
IOUT =10mA, 1.5V£(VIN -VOUT)£10.75V (Note 2)
IOUT = 0A, 2.65V£ VIN £9V (Note 2)
IOUT = 0A, 3.25V£ VIN £9V (Note 2)
IOUT = 0A, 3.95V£ VIN £9V (Note 2)
IOUT = 0A, 4.25V£ VIN £9V (Note 2)
IOUT = 0A, 4.75V£ VIN £12V (Note 2)
IOUT = 0A, 6.45V£ VIN £12V (Note 2)
APL1117
APL1117-12
APL1117-18
APL1117-25
APL1117-28
APL1117-33
APL1117-50
-
-
-
-
-
-
-
0.03
1
0.2
6
%
1
6
REGLINE
1
6
mV
1
6
1
6
1
6
Copyright ã ANPEC Electronics Corp.
3
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Electrical Characteristics (Cont.)
Unless otherwise noted, these specifications apply over CIN = 10mF , COUT = 10mF, and TA = 0 to 70°C. Typical values
refer to TA = 25°C.
APL1117
Symbol
Parameter
Load Regulation
Test Conditions
Unit
Min.
Typ.
Max.
(VIN -VOUT)=3V, 0£ IOUT £1A (Note 2)
VIN = 2.65V, 0£ IOUT £1A (Note 2)
VIN = 3.25V, 0£ IOUT £1A (Note 2)
VIN = 3.95V, 0£ IOUT £1A (Note 2)
VIN = 4.25V, 0£ IOUT £1A (Note 2)
VIN = 4.75V, 0£ IOUT £1A (Note 2)
VIN = 6.45V, 0£ IOUT £1A (Note 2)
APL1117
-
-
-
-
-
-
-
0.1
1
0.4
10
10
10
10
10
10
%
APL1117-12
APL1117-18
APL1117-25
APL1117-28
APL1117-33
APL1117-50
1
REGLOAD
1
mV
1
1
1
IOUT = 100mA (Note 3)
IOUT = 500mA (Note 3)
IOUT = 1A (Note 3)
1
1.05
1.1
1.1
1.2
1.3
VD
Dropout Voltage
-
V
ILIMIT
IADJ
Current-Limit
1000
-
-
-
mA
(VIN -VOUT) = 5V, TJ = 25°C
Adjust Pin Current
(VIN -VOUT) = 3V, IOUT = 10mA
60
120
mA
APL1117
Adjust Pin Current Change 10mA£ IOUT £1A,
-
-
0.2
1.7
5
-
DIADJ
mA
APL1117
1.4V£ (VIN -VOUT) £10.75V
Minimum Load Current
APL1117
IO
(VIN -VOUT) = 10.75V (Note 4)
mA
PSRR
TR
Ripple Rejection
fRIPPLE =120Hz, VRIPPLE = 1VP-P, (VIN -VOUT) = 3V
60
-
75
0.01
0.5
-
dB
%/ W
%
Thermal Regulation
Temperature Stability
Long-Term Stability
RMS Output Noise
0.02
TJ = 25°C, 30ms Pulse
TS
-
-
-
-
LS
-
0.3
%
TJ = 125°C, 1000Hrs.
VN
-
0.003
%
TJ = 25°C, 10Hz£F£10kHz, (% of VOUT
)
IOUT=100mA (Note2)
IOUT=500mA (Note2)
IOUT=1A (Note2)
1
1.05
1.1
1.1
1.2
1.3
VD
Dropout Voltage
-
V
ILIMIT
IADJ
Current-Limit
1000
-
-
-
mA
(VIN -VOUT)=5V, TJ=25°C
Adjust Pin Current
(VIN -VOUT)=3V, IOUT=10mA
60
120
mA
APL1117
Adjust Pin Current Change 10mA£ IOUT £1A,
-
-
0.2
1.7
5
-
DIADJ
mA
APL1117
1.4V£(VIN -VOUT) £10.75V
Minimum Load Current
APL1117
IO
(VIN -VOUT)=10.75V (Note 4)
mA
PSRR
TR
Ripple Rejection
fRIPPLE=120Hz, VRIPPLE=1VP-P, (VIN -VOUT)=3V
60
-
75
0.01
0.5
-
dB
%/W
%
Thermal Regulation
Temperature Stability
Long-Term Stability
RMS Output Noise
0.02
TJ=25°C, 30ms Pulse
TS
-
-
-
-
LS
-
0.3
%
TJ=125°C,1000Hrs.
VN
-
0.003
%
TJ=25°C,10Hz£F£10kHz, (% of VOUT
)
Copyright ã ANPEC Electronics Corp.
4
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Electrical Characteristics (Cont.)
Unless otherwise noted , these specifications apply over CIN = 10mF , COUT = 10mF , and TA = 0 to 70°C. Typical values
refer to TA = 25°C.
APL1117
Symbol
Parameter
Test Conditions
Unit
Min.
Typ.
Max.
15
10
3
SOT-223
Thermal Resistance Junction TO-252
-
-
-
qJC
°C/ W
to Case
TO-263
TO-220
3
OT
IQ
-
-
150
Over-Temperature Point
Quiescent Current
°C
5.5
5.5
10
10
mA
APL1117-12,18,25,28 VIN£9V
APL1117-33,50
VIN£12V
Note 2: See thermal regulation specifications for changes in output voltage due to heating effects. Load line regulations are measured
at a constant junction temperature by low duty cycle pulse testing.
Note 3: Dropout voltage is specified over the full output current range of the device. Dropout voltage is defined as the minimum input/
output differential measured at the specified output current. Test points and limits are also shown on the Dropout Voltage curve.
Note 4: Minimum load current is defined as the minimum output current required to maintain regulation.
Copyright ã ANPEC Electronics Corp.
5
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Typical Operating Characteristics
Load Transient Response
Line Transient Response
5
4.5
4
0.02
0.01
0
6
5
4
3
2
1
0
0.15
0.1
APL1117-33
APL1117-33
CIN=10mF
COUT=10mF Tantalum
VIN=5V
3.5
3
CIN=10mF
COUT=10mF Tantalum
IOUT=0.1A
2.5
2
0.05
0
-0.01
-0.02
-0.03
1.5
1
0.5
0
-100
-0.05
180
100
300
Time (mS)
500
700
900
-20
30
80
Time (mS)
130
Dropout Voltage vs. Output Current
Output Voltage vs. Input Voltage
1.25
1.2
6
APL1117-33
5
4
3
2
1
0
1.15
1.1
1.05
1
0.95
0.9
0
0.2
0.4
0.6
0.8
1
0
1
2
3
4
5
6
7
8
9
Output Current (A)
Input Voltage (V)
Input Current vs. Input Voltage
Current Limit vs. Input Voltage
6
5
4
3
2
1
0
2.4
APL1117-33
APL1117-33
2.2
2
1.8
1.6
1.4
1.2
1
0
2
4
6
8
10
12
5
7
9
11
13
Input Voltage (V)
Input Voltage (V)
Copyright ã ANPEC Electronics Corp.
6
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Typical Operating Characteristics (Cont.)
Output Voltage vs. Temperature
Output Voltage vs. Temperature
2.6
2.5
2.4
2.3
2.2
2.1
2
1.35
1.3
1.25
1.2
1.9
1.8
1.7
1.6
1.15
1.1
-50 -25
0
25
50
75
100 125
-50 -25
0
25
50
75
100 125
Temperature (°C)
Temperature (°C)
Output Voltage vs. Temperature
Output Voltage vs. Temperature
3.4
3.3
3.2
3.1
3
5.3
5.2
5.1
5
4.9
4.8
4.7
2.9
2.8
2.7
-50
-25
0
25
50
75 100 125
-50 -25
0
25
50
75
100 125
Temperature (°C)
Temperature (°C)
Input Current vs. Temperature
Current Limit vs. Temperature
APL1117-33
8
7
6
5
4
3
2
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1
APL1117-33
VIN-VOUT=5V
-50 -25
0
25
50
75 100 125
-50
0
50
100
150
Temperature (°C)
Temperature (°C)
Copyright ã ANPEC Electronics Corp.
7
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Typical Operating Characteristics (Cont.)
PSRR vs. Frequency
Adjustable Pin Current vs. Temperature
+0
70
Cadj=22mF
IOUT=0.1A
Vripple=1Vp-p
APL1117-33
APL1117-Adj
68
66
64
62
60
58
56
54
52
50
-10
-20
-30
-40
-50
-60
-70
-80
VIN-VOUT>=Vdropout
VIN-VOUT>=3V
-90
-100
10k
100
1k
200k
10
-50 -25
0
25
50
75 100 125
Frequency (Hz)
Temperature (°C)
Block Diagram
VOUT
VIN
Current-Limit
Thermal
Protection
Voltage
Regulation
ADJ/GND
Copyright ã ANPEC Electronics Corp.
8
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Application Information
Output Voltage
Rp
PARASITIC
LINE RESISTANCE
The APL1117 develops a 1.25V reference voltage between
the output and the adjust terminal. By placing a resistor
between these two terminals, a constant Current is caused
to flow through R1 and down through R2 to set the overall
output voltage. Normally, this current is chosen to be the
specified minimum load current of 10mA. For fixed volt-
age devices R1 and R2 are included in the device.
APL1117
IN OUT
ADJ
VIN
R1
RL
CONNECT
R1 TO CASE
R2
APL1117
VIN
VOUT
IN
OUT
ADJ
CONNECT
R2 TO LOAD
VREF
R1
R2
Figure 2. Connections for Best Load Regulation
IADJ
60mA
Input Capacitor
R2
R1
VOUT = VREF(1+
)+IADJR2
An input capacitor of 10mF or greater is recommended.
Tantalum or aluminum electrolytic capacitors can be used
for bypassing. Larger Values will improve ripple rejection
by bypassing the input to the regulator.
Figure 1. Basic Adjustable Regulator
Load Regulation
Output Capacitor
When the adjustable regulator is used, load regulation
will be limited by the resistance of the wire connecting the
regulator to the load. The data sheet specification for load
regulation is measured at the output pin of the device.
Best load regulation is obtained when the top of the re-
sistor divider (R1) is tied directly to the output pin of the
device not to the load. For fixed voltage, devices the top of
R1 is internally connected to the output, and the ground
pin can be connected to low side of the load. If R1 is
connected to the load, RP is multiplied by the divider ratio,
the effective resistance between the regulator and the
load would be:
The APL1117 requires an output capacitor to maintain sta-
bility and improve transient response. Proper capacitor
selection is important to ensure proper operation. The
APL1117 output capacitor selection is dependent upon
the ESR (equivalent series resistance) of the output ca-
pacitor to maintain stability. When the output capacitor is
10mF or greater, the output capacitor should have an ESR
less than 1W. This will improve transient response as
well as promote stability. A low-ESR solid tantalum ca-
pacitor works extremely well and provides good transient
response and stability over temperature.
Aluminum electrolytics can also be used, as long as the
ESR of the capacitor is <1W. The value of the output ca-
pacitor can be increased without limit. Higher capacitance
values help to improve transient response and ripple re-
jection and reduce output noise.
R2
Rp X (1+
), Rp = Parasitic Line Resistance
R1
Copyright ã ANPEC Electronics Corp.
9
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Application Information (Cont.)
60
55
50
45
40
35
30
Ripple Rejection
TA=25oC
The curves for Ripple Rejection were generated using an
adjustable device with the adjust pin bypassed. With a
22mF bypassing capacitor, 75dB ripple rejection is ob-
tainable at any output level. The impedance of the adjust
pin capacitor, at the ripple frequency, should be < R1. R1
is normally in the range of 100W to 200W. The size of the
required adjust pin capacitor is the function of the input
ripple frequency. At 120Hz, with R1=100W, the adjust pin
capacitor should be 13mF. For fixed voltage devices and
adjustable devices without an adjust pin capacitor, the
output ripple will increase as the ratio of the output volt-
age to the reference voltage (VOUT /VREF ).
0
2
4
6
8
10
12
14
Top Copper Area (cm2)
Figure 4. q(J-A) vs. copper area for the SOT-223 package
Thermal Consideration
The thermal resistance for each application will be af-
fected by thermal interactions with other components on
the board. Some experimentation will be necessary to
determine the actual value.
The APL1117 regulators have thermal protection to limit
junction temperature to 150ºC. However, the device is
recommended to be operated under 125ºC.
The power dissipation of APL1117 is equal to:
PD = (VIN - VOUT) x IOUT
A heatsink may be required depending on the maximum
power dissipation and maximum ambient temperature
of the application. Figure 3&4 show for the TO-252-3 and
SOT-223 the measured values q(J-A) for different copper
area sizes using a 2 layers, 1.6mm, and 6Sq. cm FR-4
PCB with 2oz. copper and a ground plane layer on the
backside area used for heatsinking. It can be used as a
rough guideline in estimating thermal resistance. Both
the TO-252-3 and SOT-223 packages use a copper plane
on the PCB and the PCB itself as a heatsink. To optimize
the heat sinking ability of the plane and PCB, solder the
tab of the package to the plane.
Maximum junction temperature is equal to:
TJUNCTION(Note) = TAMBIENT + (PD x qJA)
Note: TJUNCTION must not exceed 125°C
Safe Operation Area
Using the experiment result of previous Thermal Con-
sideration (choose the one with 1.5cmx1.5cm polygen
area) and q(J-A)=50°C/W spec, the safe operation area of
APL1117 in TO-252-3 and SOT-223 packages can be ob-
tained as Figure 5.
1200
50
TA=25oC
TA=25oC
1000
45
40
35
30
25
800
600
TA=55oC
400
TA=85oC
200
0
0.851 1.31.45 1.75 2.05 2.35 2.65 2.953.1
Input-Output Voltage Differential (V)
Figure 5. Safe Operation Area of APL1117 in TO-252-3
and SOT-223 packages (limited by Power Dissipation with
TJUNCTION < 125°C)
0
2
4
6
8
10
12
14
Top Copper Area (cm2)
Figure 3. q(J-A) vs. copper area for the TO-252-3 package
Copyright ã ANPEC Electronics Corp.
10
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Package Information
TO-220
E
A
E2
A1
E1
E/2
A2
b
e
c
b2
S
Y
M
B
O
L
TO-220
MILLIMETERS
INCHES
MIN.
3.56
0.51
2.03
0.38
1.14
0.36
MAX.
4.83
1.40
2.92
1.02
1.78
0.61
MIN.
MAX.
A
0.140
0.020
0.080
0.015
0.045
0.014
0.560
0.330
0.480
0.380
0.270
0.190
0.055
0.115
0.040
0.070
0.024
0.650
0.355
0.507
0.420
0.350
0.030
A1
A2
b
b2
c
D
14.22
8.38
16.51
9.02
D1
D2
E
12.19
9.65
12.88
10.67
8.89
E1
E2
6.86
0.76
e
H1
L
2.54 BSC
0.100 BSC
0.230
0.500
0.270
0.580
0.250
0.161
0.135
5.84
6.86
14.73
6.35
4.09
3.43
12.70
L1
P
0.139
0.100
3.53
2.54
Q
Note: Follow JEDEC TO-220 AB.
Copyright ã ANPEC Electronics Corp.
11
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Package Informaion
TO-252-3
SEATING PLANE <4 mils
E1
-T-
c2
E
A
b3
c
b
e
SEE VIEW A
GAUGE PLANE
SEATING PLANE
L
VIEW A
TO-252-3
S
Y
M
B
O
L
MILLIMETERS
MIN.
INCHES
MAX.
2.39
0.13
0.89
5.46
0.61
0.89
MIN.
MAX.
0.094
0.005
0.035
0.215
0.024
0.035
0.245
A
2.18
0.086
A1
b
0.020
0.195
0.018
0.018
0.210
0.180
0.250
0.150
0.50
4.95
b3
c
0.46
0.46
5.33
4.57
6.35
3.81
c2
D
D1
E
6.22
6.00
6.73
0.236
0.265
E1
e
0.236
6.00
2.29 BSC
0.090 BSC
0.370
0.035
0.035
0.410
0.070
0.080
0.040
8°
9.40
0.90
0.89
10.41
1.78
2.03
1.02
8°
H
L
L3
L4
0
0°
0°
Note : Follow JEDEC TO-252 .
Copyright ã ANPEC Electronics Corp.
12
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Package Information
TO-263-3
A
E1
c2
E
b
b2
c
e
SEE VIEW A
SEATING PLANE
GAUGE PLANE
L
VIEW A
S
Y
M
TO-263-3
MILLIMETERS
MIN.
INCHES
B
O
MAX.
4.83
0.25
0.99
1.78
0.74
MIN.
MAX.
0.190
0.010
0.039
0.070
0.029
0.065
0.380
0.354
0.450
0.354
L
A
4.06
0.160
0.000
0.020
0.045
0.015
0.045
0.330
0.236
0.380
0.245
A1
b
0.00
0.51
1.14
0.38
b2
c
c2
D
1.14
8.38
6.00
9.65
6.22
1.65
9.65
9.00
11.43
9.00
D1
E
E1
e
2.54 BSC
0.100 BSC
14.61
1.78
15.88
2.79
1.68
1.78
0.575
0.070
0.625
0.110
0.066
0.070
H
L
L1
L2
q
o
o
o
o
0
8
0
8
Note : Follow JEDEC TO-263 AB.
Copyright ã ANPEC Electronics Corp.
13
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Package Information
SOT-223
D
b2
SEE
VIEW A
e
c
e1
GAUGE PLANE
SEATING PLANE
L
b
VIEW A
SOT-223
S
Y
M
B
O
MILLIMETERS
MIN. MAX.
INCHES
MIN.
MAX.
L
A
1.80
0.10
1.70
0.84
3.10
0.071
0.004
0.067
0.033
0.122
0.013
0.264
0.287
0.146
0.001
0.059
0.026
0.114
0.009
0.248
0.264
0.130
A1
A2
b
0.02
1.50
0.66
2.90
b2
c
0.23
6.30
6.70
3.30
0.33
6.70
D
E
7.30
3.70
E1
e
2.30 BSC
4.60 BSC
0.091 BSC
0.181 BSC
e1
L
0.75
0.030
0
10
0°
10°
0
Note : 1. Follow from JEDEC TO-261 AA.
2. Dimension D and E1 are determined at the outermost extremes
of the plastic exclusive of mold flash, tie bar burrs, gate burrs,
and interlead flash, but including any mismatch between the top
and bottom of the plastic body.
Copyright ã ANPEC Electronics Corp.
14
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Carrier Tape & Reel Dimension
P0
P2
P1
OD0
A
K0
A0
A
OD1
B
B
SECTION A-A
SECTION B-B
d
T1
Application
TO-252-3
A
H
T1
C
d
D
W
E1
F
7.50±0.05
K0
16.4+2.00 13.0+0.50
-0.00 -0.20
330.0±2.00 50 MIN.
1.5 MIN.
D1
20.2 MIN. 16.0±0.30 1.75±0.10
P0
4.0±0.10
A
P1
8.0±0.10
H
P2 D0
T
A0
B0
1.5+0.10
-0.00
0.6+0.00
-0.40
2.0±0.05
1.5 MIN.
d
6.80±0.20 10.40±0.20 2.50±0.20
Application
TO-263-3
T1
C
D
W
E1
F
11.5±0.10
K0
24.4+2.00 13.0+0.50
-0.00 -0.20
330.0±2.00 50 MIN.
1.5 MIN.
D1
20.2 MIN. 24.0±0.30 1.75±0.10
P0
4.0±0.10
A
P1
16.0±0.10
H
P2 D0
T
A0
10.8±0.20 16.1±0.20
E1
B0
1.5+0.10
-0.00
0.6+0.00
-0.40
2.0±0.10
1.5 MIN.
d
5.2±0.20
F
Application
SOT-223
T1
C
D
W
12.4+2.00 13.0+0.50
-0.00 -0.20
320.0±2.00 50 MIN.
P0 P1
1.5 MIN.
D1
20.2 MIN. 12.00±0.30 1.75±0.10
5.50±0.05
K0
P2 D0
T
A0
B0
1.5+0.10
-0.00
0.6+0.00
-0.40
4.00±0.10 8.00±0.10 2.00±0.50
1.5 MIN.
6.90±0.20 7.50±0.20 2.10±0.20
(mm)
Copyright ã ANPEC Electronics Corp.
15
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Devices Per Unit
Package Type
TO-252-3
Unit
Quantity
2500
Tape & Reel
Tape & Reel
Tape & Reel
TO-263-3
800
SOT-223
2500
Taping Direction Information
TO-252-3
USER DIRECTION OF FEED
TO-263-3
USER DIRECTION OF FEED
Copyright ã ANPEC Electronics Corp.
16
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Taping Direction Information
SOT-223
USER DIRECTION OF FEED
Classification Profile
Copyright ã ANPEC Electronics Corp.
17
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Classification Reflow Profiles
Profile Feature
Sn-Pb Eutectic Assembly
Pb-Free Assembly
Preheat & Soak
100 °C
150 °C
60-120 seconds
150 °C
200 °C
60-120 seconds
Temperature min (Tsmin
)
Temperature max (Tsmax
)
Time (Tsmin to Tsmax) (ts)
Average ramp-up rate
(Tsmax to TP)
3 °C/second max.
3°C/second max.
Liquidous temperature (TL)
Time at liquidous (tL)
183 °C
60-150 seconds
217 °C
60-150 seconds
Peak package body Temperature
(Tp)*
See Classification Temp in table 1
20** seconds
See Classification Temp in table 2
30** seconds
Time (tP)** within 5°C of the specified
classification temperature (Tc)
Average ramp-down rate (Tp to Tsmax
)
6 °C/second max.
6 °C/second max.
6 minutes max.
8 minutes max.
Time 25°C to peak temperature
* Tolerance for peak profile Temperature (Tp) is defined as a supplier minimum and a user maximum.
** Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum.
Table 1. SnPb Eutectic Process – Classification Temperatures (Tc)
Volume mm3
350
Package
Thickness
<2.5 mm
³ 2.5 mm
Volume mm3
<350
235 °C
220 °C
220 °C
220 °C
Table 2. Pb-free Process – Classification Temperatures (Tc)
Package
Thickness
<1.6 mm
Volume mm3
Volume mm3
350-2000
260 °C
Volume mm3
<350
260 °C
260 °C
250 °C
>2000
260 °C
245 °C
245 °C
1.6 mm – 2.5 mm
³ 2.5 mm
250 °C
245 °C
Reliability Test Program
Test item
SOLDERABILITY
HOLT
Method
JESD-22, B102
JESD-22, A108
JESD-22, A102
JESD-22, A104
MIL-STD-883-3015.7
JESD-22, A115
JESD 78
Description
5 Sec, 245°C
1000 Hrs, Bias @ Tj=125°C
168 Hrs, 100%RH, 2atm, 121°C
500 Cycles, -65°C~150°C
VHBM≧2KV
PCT
TCT
HBM
MM
VMM≧200V
10ms, 1tr≧100mA
Latch-Up
Copyright ã ANPEC Electronics Corp.
18
www.anpec.com.tw
Rev. C.10 - Sep., 2010
APL1117
Customer Service
Anpec Electronics Corp.
Head Office :
No.6, Dusing 1st Road, SBIP,
Hsin-Chu, Taiwan, R.O.C.
Tel : 886-3-5642000
Fax : 886-3-5642050
Taipei Branch :
2F, No. 11, Lane 218, Sec 2 Jhongsing Rd.,
Sindian City, Taipei County 23146, Taiwan
Tel : 886-2-2910-3838
Fax : 886-2-2917-3838
Copyright ã ANPEC Electronics Corp.
Rev. C.10 - Sep., 2010
19
www.anpec.com.tw
相关型号：
APL111733GC-TUG
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111733GC-TUL
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111733UC-TRG
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111733UC-TRL
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111733UC-TUG
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111733UC-TUL
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111733VC-TRG
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111733VC-TRL
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111733VC-TUG
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111733VC-TUL
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111750FC-TRG
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111750FC-TRL
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
©2020 ICPDF网 联系我们和版权申明