APL1117-33GC-TU [ANPEC]
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V and 3.3V; 1A低压降快速响应正可调稳压器和固定1.8V ， 2.5V ， 2.85V和3.3V
| 型号： | APL1117-33GC-TU |
| 厂家： | 
ANPEC ELECTRONICS COROPRATION |
| 描述： | 1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V and 3.3V |
| 文件： | 总18页 (文件大小：158K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
APL1117
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed
1.8V, 2.5V, 2.85V and 3.3V
Features
General Description
The APL1117 is a low dropout three-terminal adjust-
able regulators with 1A output current capability. In
order to obtain lower dropout voltage and faster tran-
sient response, which is critical for low voltage ap-
plications , the APL1117 has been optimized. The
device is available in an adjustable version and fixed
output voltages of 1.8V, 2.5V, 2.85V and 3.3V. The
output available voltage range of an adjustable ver-
sion is from 1.25~10.7V with an input supply below
12V. Dropout voltage is guaranteed at a maximum of
1.3V at 1A. Current limit is trimmed to ensure speci-
fied output current and controlled short-circuit current.
On-chip thermal limiting provides protection against
any combination of overload that would create exces-
sive junction temperatures. The APL1117 is available
in the industry standard 3-pin TO-220, TO-252, TO-
263, and the low profile surface mount SOT-223
power packages which can be used in applications
where space is limited.
•
•
•
Guaranteed Output Voltage Accuracy within 2%
Fast Transient Response
Guaranteed Dropout Voltage at Multiple
Currents
•
•
•
•
•
•
•
Load Regulation : 0.1% Typ.
Line Regulation : 0.03% Typ.
Low Dropout Voltage : 1.1V Typ. at IOUT =1A
Current Limit : 1A Typ. at TJ=25°C
On-Chip Thermal Limiting : 150°C Typ.
Adjustable Output : 1.25~10.7V
Standard 3-pin TO-220, TO-252, TO-263 and
SOT-223 Power Packages
Applications
Pin Description
Front View for TO-220
•
•
•
•
Active SCSI Terminators
3
Low Voltage Logic Supplies
Battery-Powered Circuitry
VIN
2
1
VOUT
Post Regulator for Switching Power Supply
ADJ/GND
Front View for TO-263
VIN
VOUT
3
2
1
TAB is VOUT
ADJ/GND
Front View for TO-252
VIN
3
2
1
TAB IS VOUT
VOUT
ADJ/GND
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise
customers to obtain the latest version of relevant information to verify before placing orders.
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
1
www.anpec.com.tw
APL1117
Pin Description (Cont.)
Front View for SOT-223
3
2
1
IN
T A B IS V O
U T
O U T
A D J /G N D
Ordering and Marking Information
P ackage C ode
F : TO -220
A P L1117-
G : TO -263
U : TO -252
V : S O T-223
T em p. R ange
H andling C ode
°
C : 0 to 70
C
H andling C ode
TU : T ube
V oltage C ode
18 : 1.8V
T em p. R ange
P ackage C ode
TR : Tape & R eel
25 : 2.5V 28 : 2.85V
33 : 3.3V
V oltage C ode
B lank : A djusta ble V ersion
A P L1117
X X X X X
- D ate C ode
- D ate C ode
X X X X X
X X X X X
A P L1117 F /G /U :
A P L1117 V
:
X X X X X
X X X X X
-
-
D ate C ode
A P L1117
X X X X X
18
A P L1117
X X X X X 18
A P L1117-18F /G /U :
A P L1117-18V :
D ate C ode
A P L1117
X X X X X
25
A P L1117
X X X X X 25
A P L1117-25F /G /U :
A P L1117-28F /G /U :
A P L1117 -33F /G /U :
A P L1117-25V :
A P L1117-28V :
X X X X X
X X X X X
X X X X X
-
-
-
D ate C ode
D ate C ode
D ate C ode
X X X X X - D ate C ode
X X X X X - D ate C ode
A P L1117
X X X X X
28
A P L1117
X X X X X 28
A P L1117
X X X X X
33
A P L1117
X X X X X 33
A P L1117-33V :
X X X X X - D ate C ode
A P L1117
X X X X X
Absolute Maximum Ratings
Symbol
Parameter
Rating(Note)
Unit
VI
Input Voltage
APL1117, APL1117-33
APL1117-18, APL1117-25, APL1117-28
15
9
V
TJ
Operating Junction Temperature Range
Control Section
C
°
0 to 125
0 to 150
Power Transistor
TSTG
TL
Storage Temperature Range
-65 to +150
C
C
°
Lead Temperature (Soldering, 10 second)
260
°
Note : The values here show the absolute maximum rating, and for normal usage please refer the test condition in Electrical
Characteristics Table.
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
2
www.anpec.com.tw
APL1117
Electrical Characteristics (Cont.)
Symbol
Parameter
Test Conditions
1A, 1.4V (V -V
APL1117
Min. Typ. Max.
Unit
VREF
Reference Voltage
V
10mA I
)
10.75V,
≤
≤
≤
≤
OUT
IN
OUT
1.225 1.250 1.275
T =0~125 C
°
J
VOUT
Output Voltage
APL1117-18
T =0~125 C,
°
J
1.764 1.800 1.836
2.450 2.500 2.550
2.790 2.850 2.910
3.235 3.300 3.365
0.03 0.2
0 I
1.5A, 3.5V V 9V,
≤ ≤
≤
≤
OUT
IN
APL1117-25
APL1117-28
APL1117-33
T =0~125 C,
°
J
0 I
≤
1A, 4V V 9V,
≤ ≤
≤
OUT
IN
V
T =0~125 C,
°
J
0 I
1A, 4.25V V 9V,
≤ ≤
≤
≤
OUT
IN
T =0~125 C,
°
J
0 I
≤
1A, 4.75V V 12V,
≤ ≤
≤
OUT
IN
REGLINE Line Regulation
APL1117
(Note1)
%
mV
IOUT=10mA, 1.5V (V -V ) 10.75V
IOUT=0A, 3.5V V 9V
IOUT=0A, 4V V 5.5V
IOUT=0A, 4.25V V 5.15V
≤
≤
IN
OUT
(Note1)
APL1117-18
APL1117-25
APL1117-28
APL1117-33
1
1
1
1
6
6
6
6
≤
≤
IN
(Note1)
≤
≤
IN
(Note1)
(Note1)
≤
≤
≤
≤
IN
IOUT=0A, 4.75V V 7.75V
IN
REGLOAD Load Regulation
(Note1)
APL1117
APL1117-18
APL1117-25
APL1117-28
APL1117-33
0.1
1
1
1
1
0.4
10
10
10
10
%
mV
(VIN -VOUT)=3V, 0 I
1A
≤
≤
OUT
(Note1)
V =3.5V, 0 I
1A
≤
≤
IN
OUT
(Note1)
V =4V, 0 I
1A
≤
≤
IN
OUT
(Note1)
V =4.25V, 0 I
1A
1A
≤
≤
IN
OUT
(Note1)
V =4.75V, 0 I
≤
≤
IN
OUT
(Note2)
VD
Dropout Voltage
IOUT=100mA
IOUT=500mA
1
1.1
(Note2)
1.05 1.2
V
(Note2)
IOUT=1A
1.1
1.3
ILIMIT
IADJ
Current Limit
1000
mA
(VIN -VOUT)=5V, T =25 C
°
J
Adjust Pin Current (VIN -VOUT)=3V, IOUT=10mA
APL1117
Adjust Pin Current
Change APL1117
60
120
5
A
µ
0.2
I
10mA I
1A,
≤
A
∆
≤
µ
OUT
ADJ
1.4V (V -V
(VIN -VOUT)=10.75V
)
OUT
10.75V
≤
≤
IN
(Note3)
IO
Minimum Load
Current APL1117
1.7
75
mA
dB
PSRR Ripple Rejection
fRIPPLE=120Hz, VRIPPLE=1VP-P,
(VIN -VOUT)=3V
60
TR
TS
Thermal Regulation
0.01 0.02 %/ W
T =25 C, 30ms Pulse
°
J
Temperature
Stability
0.5
%
LS
Long -Term
Stability
0.3
%
T =125 C,1000Hrs.
°
J
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
3
www.anpec.com.tw
APL1117
Electrical Characteristics (Cont.)
APL1117
Min. Typ. Max.
0.003
Symbol
VN
Parameter
Test Conditions
T =25 C,10Hz F 10kHz, (% of V
Unit
RMS Output Noise
%
)
OUT
°
≤ ≤
J
Thermal Resistance Junction to Case, at Tab
15
50
C/ W
°
θth
Junction to Ambient
OT
IQ
Over Temperature
Point
Quiescent Current
150
C
°
APL1117-18
APL1117-25
APL1117-28
APL1117-33
5.5
5.5
5.5
5.5
10
10
10
10
mA
VIN 9V
≤
VIN 9V
≤
VIN 9V
≤
VIN 12V
≤
Note 1 : See thermal regulation specifications for changes in output voltage due to heating effects. Load line regulations are mea-
sured at a constant junction temperature by low duty cycle pulse testing.
Note 2 : Dropout voltage is specified over the full output current range of the device. Dropout voltage is defined as the minimum input/output
differential measured at the specified output current. Test points and limits are also shown on the Dropout Voltage curve.
Note 3 : Minimum load current is defined as the minimum output current required to maintain regulation.
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
4
www.anpec.com.tw
APL1117
Application Circuits
1.25V to 10.7V Adjustable Regulator
APL1117
Improving Ripple Rejection
APL1117
VIN
IN
OUT
VOUT1
VIN
IN
OUT
ADJ
VOUT
R1
121
R1
121Ω
1%
ADJ
+
Ω
10µ F
100µF
C2
150µ F
+
+
10µ
F
C1*
R2
365Ω
R2
1k
C1
10µF
+
1%
* C1 improves ripple rejection.
XC should be approximately
equal to R1 at ripple frequency
* Needed if device is far from filter capacitors
R1 + R2
V
OUT = 1.250V X
R1
5V Regulator with Shutdown
APL1117
VIN
IN
OUT
ADJ
5V
121
1%
Ω
+
10µ
F
+
1k
100µ
F
TTL
365
1%
Ω
1k
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
5
www.anpec.com.tw
APL1117
Typical Characteristics
Load Transietn Response
Line Transient Response
APL1117-33
APL1117-33
5
0.02
0.01
0
6
5
4
3
2
1
0
0.15
0.1
4.5
4
3.5
3
CIN=10µF
COUT=10µF Tantalum
IOUT=0.1A
2.5
0.05
0
CIN=10µF
2
1.5
1
-0.01
-0.02
-0.03
COUT=10µF Tantalum
VIN=5V
0.5
0
-0.05
-100
100
300
500
700
900
-20
30
80
130
180
Time (µS)
Time (µS)
Dropout Voltage vs. Output Current
Output Voltage vs. Input Voltage
APL1117-33
1.25
1.2
3.5
3
1.15
1.1
2.5
2
1.05
1
1.5
1
0.95
0.9
0.5
0
0
0.2
0.4
0.6
0.8
1
0
1
2
3
4
5
6
7
8
9
Output Current (A)
Input Voltage (V)
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
6
www.anpec.com.tw
APL1117
Typical Characteristics Cont.
Input Current vs. Input Voltage
Current Limit vs. Input Voltage
APL1117-33
APL1117-33
2.4
2.2
2
6
5
4
3
2
1
0
1.8
1.6
1.4
1.2
1
0
2
4
6
8
10
12
5
7
9
11
13
Input Voltage (V)
Input Voltage (V)
Output Voltage vs. Temperature
Output Voltage vs. Temperature
3.4
3.3
3.2
3.1
3
2.6
2.5
2.4
2.3
2.2
2.1
2
1.9
1.8
1.7
1.6
2.9
2.8
2.7
-50
-25
0
25
50
75
100
125
-50
-25
0
25
50
75
100
125
Temperature (°C)
Temperature (°C)
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
7
www.anpec.com.tw
APL1117
Typical Characteristics Cont.
Adjustable Pin Current vs. Temperature
Input Current vs. Tmeperature
APL1117-33
APL1117-Adj
8
7
6
5
4
3
2
70
68
66
64
62
60
58
56
54
52
50
-50
-25
0
25
50
75
100 125
-50
-25
0
25
50
75
100
125
Temperature (°C)
Temperature (°C)
Current Limit vs. Temperature
PSRR vs. Frequency
APL1117-33
APL1117-33
1.9
+0
Cadj=22µF
-10 IOUT=0.1A
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1
Vripple=1Vp-p
-20
-30
-40
-50
-60
-70
-80
VIN-VOUT=5V
VIN-VOUT>=Vdropout
-90
VIN-VOUT>=3V
-100
10k 20k
50 100 200
500 1k 2k
5k
50k 200k
-50
0
50
100
150
10 20
Temperature (°C)
Frequency (Hz)
Copyright ANPEC Electronics Corp.
8
www.anpec.com.tw
6
Rev. B.8 - Jun., 2003
APL1117
Application Information
Rp
Output Voltage
PARASITIC
APL1117
IN OUT
ADJ
LINE RESISTANCE
The APL1117 develops a 1.25V reference voltage
between the output and the adjust terminal. By plac-
ing a resistor between these two terminals, a con-
stant Current is caused to flow through R1 and down
through R2 to set the overall output voltage. Normally
this current is chosen to be the specified minimum
load current of 10mA. For fixed voltage devices R1
and R2 are included in the device.
VIN
R1
RL
CONNECT
R1 TO CASE
R2
CONNECT
R2 TO LOAD
APL1117
VIN
VOUT
IN
OUT
ADJ
Figure 2. Connections for Best Load Regulation
VREF
R1
R2
Input Capacitor
IADJ
60µA
An input capacitor of 10µF or greater is
recommended. Tantalum, or aluminum electrolytic
capacitors can be used for bypassing. Larger Val-
ues will improve ripple rejection by bypassing the in-
put to the regulator.
R2
)+IADJR2
R1
V
OUT = VREF(1+
Figure 1. Basic Adjustable Regulator
Load Regulation
Output Capacitor
When the adjustable regulator is used. Load regula-
tion will be limited by the resistance of the wire con-
necting the regulator to the load. The data sheet speci-
fication for load regulation is measured at the output
pin of the device. Best load regulation is obtained
when the top of the resistor divider (R1) is tied di-
rectly to the output pin of the device, not to the load.
For fixed voltage devices the top of R1 is internally
connected to the output, and the ground pin can be
connected to low side of the load. If R1 were con-
nected to the load, RP is multiplied by the divider
ratio, the effective resistance between the regulator
and the load would be:
The APL1117 requires an output capacitor to main-
tain stability and improve transient response. Proper
capacitor selection is important to ensure proper
operation. The APL1117 output capacitor selection
is dependent upon the ESR (equivalent series
resistance) of the output capacitor to maintain stability.
When the output capacitor is 10uF or greater, the
output capacitor should have an ESR less than 1Ω.
This will improve transient response as well as pro-
mote stability. A low-ESR solid tantalum capacitor
works extremely well and provides good transient re-
sponse and stability over temperature.
R2
Rp X (1+ ), Rp = Parasitic Line Resistance
R1
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
9
www.anpec.com.tw
APL1117
Application Information (Cont.)
Figure 3&4 shows for the TO-252 and SOT-223 the
measured values of θ(J-A) for different copper area
sizes using a 2 layers, 1.6mm, and 6Sq. cm FR-4
PCB with 2oz. copper and a ground plane layer on
the backside area used for heatsinking. It can be
used as a rough guideline in estimating thermal
resistance.
Output Capacitor (Cont.)
Aluminum electrolytics can also be used, as long as
the ESR of the capacitor is <1Ω. The value of the
output capacitor can be increased without limit. Higher
capacitance values help to improve transient response
and ripple rejection and reduce output noise.
Ripple Rejection
50
TA=25°C
The curves for Ripple Rejection were generated us-
ing an adjustable device with the adjust pin bypassed.
With a 22µF bypassing capacitor 75dB ripple rejec-
tion is obtainable at any output level. The impedance
of the adjust pin capacitor, at the ripple frequency,
should be < R1. R1 is normally in the range of 100Ω-
200Ω. The size of the required adjust pin capacitor
is a function of the input ripple frequency. At 120Hz,
with R1=100Ω, the adjust pin capacitor should be
13µF. For fixed voltage devices, and adjustable de-
vices without an adjust pin capacitor, the output ripple
will increase as the ratio of the output voltage to the
reference voltage (VOUT /VREF ).
45
40
35
30
25
0
2
4
6
8
10
12
14
2
Top Copper Area (cm )
Figure 3.
θ(J-A) vs. copper area for the SOT-252 package
Thermal Considerations
APL1117 has thermal protection which limits junction
temperature to 150°C. However, device functionality
is only guaranteed to a maximum junction tempera-
ture of +125°C.
Both the TO-220, TO-252, TO-263 and SOT-223
packages use a copper plane on the PCB and the
PCB itself as a heatsink. To optimize the heat sinking
ability of the plane and PCB, solder the tab of the
package to the plane.
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
10
www.anpec.com.tw
APL1117
Application Information (Cont.)
Thermal Considerations (Cont.)
60
TA=25°C
55
50
45
40
35
30
0
2
4
6
8
10
12
14
2
Top Copper Area (cm )
Figure 4.
θ(J-A) vs. copper area for the SOT-223 package
The thermal resistance for each application will be
affected by thermal interactions with other compo-
nents on the board. Some experimentation will be
necessary to determine the actual value.
The power dissipation of APL1117 is equal to :
PD = (VIN - VOUT) x IOUT
Maximum junction temperature is equal to :
TJUNCTION = TAMBIENT + (PD x θJA)
Note: TJUNCTION must not exceed 125°C
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
11
www.anpec.com.tw
APL1117
Package Information
TO-220 ( Reference JEDEC Registration TO-220)
D
Q
b
e
E
b1
e1
L1
L
H1
A
c
J1
F
Millimeters
Dim
Inches
Min.
3.56
1.14
0.51
0.31
14.23
2.29
4.83
9.65
0.51
5.84
2.03
12.7
3.65
3.53
2.54
Max.
4.83
1.78
1.14
1.14
16.51
2.79
5.33
10.67
1.40
6.86
2.92
14.73
6.35
4.09
3.43
Min.
0.140
0.045
0.020
0.012
0.560
0.090
0.190
0.380
0.020
0.230
0.080
0.500
0.143
0.139
0.100
Max.
0.190
0.070
0.045
0.045
0.650
0.110
0.210
0.420
0.055
0.270
0.115
0.580
0.250
0.161
0.135
A
b1
b
c
D
e
e1
E
F
H1
J1
L
L1
R
Q
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
12
www.anpec.com.tw
APL1117
Package Informaion
TO-252( Reference JEDEC Registration TO-252)
E
A
b2
C1
L2
D
H
L1
L
b
C
e1
A1
D1
E1
Millimeters
Dim
Inches
Min.
2.18
Max.
2.39
1.27
0.89
5.461
0.58
0.58
6.22
Min.
Max.
0.094
0.050
0.035
0.215
0.023
0.023
0.245
A
A1
b
0.086
0.035
0.020
0.205
0.018
0.018
0.210
0.89
0.508
5.207
0.46
b2
C
C1
D
0.46
5.334
D1
E
5.2 REF
5.3 REF
0.205 REF
0.209 REF
6.35
6.73
0.250
0.265
E1
e1
H
3.96
9.398
0.51
0.64
0.89
5.18
0.156
0.370
0.020
0.025
0.035
0.204
0.410
10.41
L
L1
L2
1.02
0.040
0.080
2.032
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
13
www.anpec.com.tw
APL1117
Package Information
TO-263 ( Reference JEDEC Registration TO-263)
E
TERMINAL 4
L2
E1
D1
D
L
L3
b2
b
e
e1
A
c2
R
Φ
1
L1
DETAIL "A"ROTED
L4
c
Millimeters
Inches
Min.
Max.
Min.
Max.
Dim
A
b
4.06
0.51
1.14
4.83
1.016
1.651
0.160
0.02
0.190
0.040
0.065
b2
c
0.045
0.38 TYP.
2.54 TYP
0.015 TYP.
0.100 TYP
c2
D
e
e1
L
L1
L2
L3
1.14
8.64
9.65
1.40
9.65
10.54
0.045
0.340
0.380
0.055
0.380
0.415
14.60
2.24
1.02
1.20
15.88
2.84
2.92
1.78
0.575
0.090
0.040
0.050
0.625
0.110
0.112
0.070
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
14
www.anpec.com.tw
APL1117
Package Information
SOT-223( Reference JEDEC Registration SOT-223)
D
A
a
B1
c
H
E
L
K
e
A1
e1
b
B
Dim
Millimeters
Inches
Min.
Max.
1.80
0.08
0.80
3.10
0.32
6.70
3.70
Min.
0.06
Max.
0.07
A
A1
B
B1
c
1.50
0.02
0.60
2.90
0.28
6.30
3.30
0.02
0.11
0.01
0.25
0.13
0.03
0.12
0.01
0.26
0.15
D
E
e
2.3 BSC
4.6 BSC
0.09 BSC
0.18 BSC
e1
H
L
6.70
0.91
1.50
7.30
1.10
2.00
0.26
0.04
0.06
0.29
0.04
0.08
K
0
10
0
10
°
α
°
°
°
13
13
°
β
°
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
15
www.anpec.com.tw
APL1117
Physical Specifications
Terminal Material
Lead Solderability
Packaging
Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb
Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.
2500 devices per reel
Reflow Condition (IR/Convection or VPR Reflow)
Reference JEDEC Standard J-STD-020A APRIL 1999
Peak temperature
°
183 C
Pre-heat temperature
Time
Classification Reflow Profiles
Convection or IR/
Convection
VPR
°
±
°
°
Average ramp-up rate(183 C to Peak)
3 C/second max.
120 seconds max.
60 ~ 150 seconds
10 ~ 20 seconds
10 C /second max.
°
25 C)
Preheat temperature 125
°
C
Temperature maintained above 183
Time within 5 C of actual peak temperature
Peak temperature range
°
60 seconds
° °
215~ 219 C or 235 +5/-0 C
°
°
220 +5/-0 C or 235 +5/-0 C
Ramp-down rate
°
°
6 C /second max.
10 C /second max.
°
6 minutes max.
Time 25 C to peak temperature
Package Reflow Conditions
pkg. thickness < 2.5mm and pkg.
volume <
pkg. thickness < 2.5mm and
pkg. thickness
and all bags
≥ 2.5mm
≥
pkg. volume
350 mm
°
°
C
Convection 220 +5/-0 C
Convection 235 +5/-0
°
°
C
VPR 215-219 C
VPR 235 +5/-0
IR/Convection 235 +5/-0 C
°
°
IR/Convection 220 +5/-0 C
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
16
www.anpec.com.tw
APL1117
Reliability test program
Test item
SOLDERABILITY
HOLT
PCT
TST
Method
Description
MIL-STD-883D-2003
MIL-STD-883D-1005.7
JESD-22-B, A102
MIL-STD-883D-1011.9
MIL-STD-883D-3015.7
JESD 78
245 C , 5 SEC
°
1000 Hrs Bias @ 125 C
°
168 Hrs, 100 % RH , 121 C
°
-65 C ~ 150 C, 200 Cycles
VHBM > 2KV, VMM > 200V
10ms , Itr > 100mA
°
°
ESD
Latch-Up
Carrier Tape & Reel Dimension
t
D
P
Po
E
P1
Bo
F
W
Ao
J
D1
Ko
T2
C
A
B
T1
A
B
C
J
T 1
T 2
W
P
E
A p p lic a tio n
T O -2 5 2
1 6 .4 + 0 .3
-0 .2
1 6 + 0 .3
- 0 .1
3 3 0
3
1 0 0
2
1 3
0 . 5
2
0 .5
2 .5 0 .5
8
0 .1
±
±
±
±
±
±
1 .7 5 ± 0 .1
F
D
D 1
1 .5 + 0 .1 1 .5 0 .2 5 4 .0
P o
P 1
A o
B o
K o
t
7 .5
0 .1
0 .1 2 .0
0 .1 6 .8
0 .1 1 0 .4 0 .1 2 .5 0 .1
0 .3 0 .0 5
±
±
±
±
±
±
±
P
±
±
A
B
C
J
T 1
T 2
W
E
A p p lic a tio n
T O -2 6 3
2 4 + 0 .3
- 0 .1
3 8 0
F
3
8 0
2
1 3
0 . 5
2
0 .5
2 4
4
2
0 .3
1 6
0 .1 1 .7 5 0 .1
±
±
±
±
±
±
±
D
D 1
0 .1 1 .5 + 0 .1 1 .5 0 .2 5 4 .0
P o
P 1
A o
0 .1 1 0 .8
B o
K o
t
0 .3 5 0 .0 1
±
11 .5
0 .1 2 .0
0 .1 1 6 .1 0 .1 5 .2 0 .1
±
±
±
±
±
±
W
±
±
3
A
B
C
J
T 1
T 2
0 .2
P
E
A p p lic a tio n
S O T -2 2 3
1 2 .7 5
0 .1 5
±
3 3 0
1
6 2 1 .5
2
0 .6
1 2 .4 + 0 .2
P 1
2
1 2
0 .3
8
0 .1
1 .7 5 0 .1
±
±
±
±
±
±
F
D
D 1
P o
±
A o
B o
K o
2 .1 0 .1
t
5 .5
0 .0 5 1 .5 + 0 .1
1 .5 + 0 .1 4 .0
0 .1 2 .0
0 .0 5 6 .9
0 .1
7 .5 0 .1
0 .3 0 .0 5
±
±
±
±
±
±
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
17
www.anpec.com.tw
APL1117
Cover Tape Dimensions
Application
TO- 252
TO- 263
Carrier Width
Cover Tape Width
Devices Per Reel
16
24
12
13.3
21.3
9.3
2500
1000
2500
SOT- 223
Customer Service
Anpec Electronics Corp.
Head Office :
5F, No. 2 Li-Hsin Road, SBIP,
Hsin-Chu, Taiwan, R.O.C.
Tel : 886-3-5642000
Fax : 886-3-5642050
Taipei Branch :
7F, No. 137, Lane 235, Pac Chiao Rd.,
Hsin Tien City, Taipei Hsien, Taiwan, R. O. C.
Tel : 886-2-89191368
Fax : 886-2-89191369
Copyright ANPEC Electronics Corp.
Rev. B.8 - Jun., 2003
18
www.anpec.com.tw
相关型号：
APL1117-33UC-TR
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V and 3.3V
ANPEC
APL1117-33UC-TU
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V and 3.3V
ANPEC
APL1117-33VC-TR
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V and 3.3V
ANPEC
APL1117-33VC-TU
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V and 3.3V
ANPEC
APL111712FC-TRG
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111712FC-TRL
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111712FC-TUG
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111712FC-TUL
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111712GC-TRG
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111712GC-TRL
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111712GC-TUG
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
APL111712GC-TUL
1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.2V,1.8V, 2.5V, 2.85V, 3.3V and 5V
ANPEC
©2020 ICPDF网 联系我们和版权申明