A43L1632AG-7UF [AMICC]
DRAM;
| 型号： | A43L1632AG-7UF |
| 厂家： | 
AMIC TECHNOLOGY |
| 描述： | DRAM 动态存储器 |
| 文件： | 总44页 (文件大小：746K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
A43L1632A
Preliminary
512K X 32 Bit X 4 Banks Synchronous DRAM
Document Title
512K X 32 Bit X 4 Banks Synchronous DRAM
Revision History
Rev. No. History
Issue Date
Remark
0.0
0.1
Initial issue
March 21, 2007
February 19, 2008
Preliminary
Add part numbering scheme
PRELIMINARY (February, 2008, Version 0.1)
AMIC Technology, Corp.
A43L1632A
Preliminary
512K X 32 Bit X 4 Banks Synchronous DRAM
Features
JEDEC standard 3.3V power supply
Auto & self refresh
LVTTL compatible with multiplexed address
64ms refresh period (4K cycle)
86 Pin TSOP (II)
Four banks / Pulse RAS
Commercial operating temperature range: 0ºC to + 70ºC
Industrial operating temperature range: -40ºC to +85ºC
for -U series
Available in 90 Balls CSP (8mm X 13mm)
Package is available to lead free (-F series)
MRS cycle with address key programs
- CAS Latency (2,3)
- Burst Length (1,2,4,8 & full page)
- Burst Type (Sequential & Interleave)
All inputs are sampled at the positive going edge of the
system clock
All Pb-free (Lead-free) products are RoHS compliant
Burst Read Single-bit Write operation
DQM for masking
Clock Frequency (max) : 166MHz @ CL=3 (-6)
143MHz @ CL=3 (-7)
General Description
The A43L1632A is 67,108,864 bits Low Power
synchronous high data rate Dynamic RAM organized as 2
X 1,048,576 words by 32 bits, fabricated with AMIC’s high
performance CMOS technology. Synchronous design
allows precise cycle control with the use of system clock.
I/O transactions are possible on every clock cycle. Range
of operating frequencies, programmable latencies allows
the same device to be useful for a variety of high
bandwidth, high performance memory system applications.
Pin Configuration
90 Balls CSP (8 mm x 13 mm)
Top View
90 Ball (8X13) CSP
1
2
3
7
8
9
A
B
C
D
E
F
DQ26
DQ28
VSSQ
VSSQ
VDDQ
VSS
A4
DQ24
VDDQ
DQ27
DQ29
DQ31
DQM3
A5
VSS
VSSQ
DQ25
DQ30
NC
VDD
VDDQ
DQ22
DQ17
NC
DQ23
VSSQ
DQ20
DQ18
DQ16
DQM2
A0
DQ21
DQ19
VDDQ
VDDQ
VSSQ
VDD
A2
A3
A1
G
H
J
A6
A10
NC
A7
A8
NC
BA1
NC
CLK
CKE
A9
BA0
CS
RAS
K
DQM1
NC
NC
DQM0
CAS
VDD
DQ6
WE
DQ7
DQ5
DQ3
VSSQ
DQ0
L
VDDQ
VSSQ
VSSQ
DQ11
DQ8
DQ10
DQ12
VDDQ
DQ15
VSS
DQ9
VSSQ
VDDQ
VDDQ
DQ4
M
N
P
R
DQ14
VSSQ
VSS
DQ1
VDDQ
VDD
DQ13
DQ2
PRELIMINARY (February, 2008, Version 0.1)
1
AMIC Technology, Corp.
A43L1632A
Pin Configuration (continued)
TSOP (II)
PRELIMINARY (February, 2008, Version 0.1)
2
AMIC Technology, Corp.
A43L1632A
Block Diagram
LWE
DQM
Data Input Register
Bank Select
512K X 32
512K X 32
512K X 32
512K X 32
CLK
DQi
Column Decoder
ADD
Latency & Burst Length
LRAS
Programming Register
LWCBR
LCAS
DQM
LRAS
LCBR
LWE
Timing Register
DQM
CLK
CKE
CS
RAS
CAS
WE
PRELIMINARY (February, 2008, Version 0.1)
3
AMIC Technology, Corp.
A43L1632A
Pin Descriptions
Symbol
Name
Description
CLK
CS
System Clock
Chip Select
Active on the positive going edge to sample all inputs.
Disables or Enables device operation by masking or enabling all inputs except CLK,
CKE and DQM
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one clock + tss prior to new command.
Disable input buffers for power down in standby.
CKE
Clock Enable
Row / Column addresses are multiplexed on the same pins.
Row address : RA0~RA10, Column address: CA0~CA7
Selects bank to be activated during row address latch time.
Selects band for read/write during column address latch time.
A0~A10
Address
BA0, BA1
Bank Select Address
Row Address Strobe
Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
RAS
CAS
Latches column addresses on the positive going edge of the CLK with CAS low.
Enables column access.
Column Address
Strobe
Write Enable
Enables write operation and Row precharge.
WE
Makes data output Hi-Z, t SHZ after the clock and masks the output.
Blocks data input when DQM0-3 active.
Data Input/Output
Mask
DQM0-3
DQ0-31
Data Input/Output
Data inputs/outputs are multiplexed on the same pins.
Power
Supply/Ground
VDD/VSS
Power Supply: +3.3V±0.3V/Ground
Data Output
Power/Ground
VDDQ/VSSQ
NC/RFU
Provide isolated Power/Ground to DQs for improved noise immunity.
No Connection
PRELIMINARY (February, 2008, Version 0.1)
4
AMIC Technology, Corp.
A43L1632A
Absolute Maximum Ratings*
*Comments
Voltage on any pin relative to VSS (Vin, Vout ) . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5V to +3.6V
Voltage on VDD supply relative to VSS (VDD, VDDQ )
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.5V to + 3.6V
Storage Temperature (TSTG) . . . . . . . . . . -55°C to +150°C
Soldering Temperature X Time (TSLODER) . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C X 10sec
Power Dissipation (PD) . . . . . . . . . . . . . . . . . . . . . . . . .0.8W
Short Circuit Current (Ios) . . . . . . . . . . . . . . . . . . . . 50mA
Permanent device damage may occur if “Absolute Maximum
Ratings” are exceeded.
Functional operation should be restricted to recommended
operating condition.
Exposure to higher than recommended voltage for extended
periods of time could affect device reliability.
Capacitance (TA=25°C, f=1MHz)
Parameter
Input Capacitance
Symbol
CI1
Condition
A0 to A10, BA0, BA1
Min
2.5
2.5
Typ
Max
4
Unit
pF
CI2
CLK, CKE,
DQM
,
,
, WE ,
4
pF
CS RAS CAS
Data Input/Output Capacitance
CI/O
DQ0 to DQ31
4
6.5
pF
DC Electrical Characteristics
Recommend operating conditions (Voltage referenced to VSS = 0V, TA = 0ºC to +70ºC or TA = -40ºC to +85ºC)
Parameter
Supply Voltage
Symbol
Min
3
Typ
Max
Unit
V
Note
VDD,VDDQ
3.3
3.6
Input High Voltage
VIH
VIL
VOH
VOL
IIL
2
-
0
-
VDD+0.3
V
Input Low Voltage
-0.3
2.0
-
0.8
-
V
Note 1
IOH = -1mA
IOL = 1mA
Note 2
Output High Voltage
Output Low Voltage
Input Leakage Current
Output Leakage Current
Output Loading Condition
V
-
0.4
5
V
-5
-
μA
μA
IOL
-5
-
5
Note 3
See Figure 1
Note: 1. VIL (min) = -2.0V AC (pulse width ≤ 3ns).
2. Any input 0V ≤ VIN ≤ VDD + 0.3V, all other pins are not under test = 0V
3. Dout is disabled, 0V ≤ Vout ≤ VDD
PRELIMINARY (February, 2008, Version 0.1)
5
AMIC Technology, Corp.
A43L1632A
Decoupling Capacitance Guide Line
Recommended decoupling capacitance added to power line at board.
Parameter
Symbol
Value
Unit
μF
Decoupling Capacitance between VDD and VSS
Decoupling Capacitance between VDDQ and VSSQ
CDC1
CDC2
0.1 + 0.01
0.1 + 0.01
μF
Note: 1. VDD and VDDQ pins are separated each other.
All VDD pins are connected in chip. All VDDQ pins are connected in chip.
2. VSS and VSSQ pins are separated each other
All VSS pins are connected in chip. All VSSQ pins are connected in chip.
DC Electrical Characteristics
(Recommended operating condition unless otherwise noted, TA = 0 to 70°C or TA = -40ºC to +85ºC)
Speed
CAS
Latency
Unit Note
-7
Symbol
Parameter
Test Conditions
Burst Length = 1
-6
3
2
130
130
Operating Current
(One Bank Active)
Icc1
tRC ≥ tRC(min), tCC ≥ tCC(min),
IOL = 0mA
mA
mA
1
110
Icc2 P
CKE ≤ VIL(max), tCC = 15ns
2
2
Precharge Standby Current
in power-down mode
Icc2 PS
CKE & CLK ≤ VIL(max), tCC = ∞
CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 15ns
12
7
ICC2N
Precharge Standby Current
in non power-down mode
Input signals are changed one time during 30ns
mA
mA
CKE ≥ VIH(min), CLK ≤ VIL(max), tCC = ∞
Input signals are stable
ICC2NS
ICC3P
CKE ≤ VIL(max), tCC = 15ns
CKE ≤ VIL(max), tCC = ∞
4
4
Active Standby Current in
power-down mode
ICC3PS
CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 15ns
Input signals are changed one time during 30ns
40
35
ICC3N
Active Standby current in
non power-down mode
(One Bank Active)
mA
mA
CKE ≥ VIH(min), CLK ≤ VIL(max), tCC = ∞
Input signals are stable
ICC3NS
3
150
140
140
120
Operating Current
(Burst Mode)
IOL = 0mA, Page Burst
All bank Activated, tCCD = tCCD (min)
ICC4
1
2
2
120
3
ICC5
ICC6
Refresh Current
mA
mA
tRC ≥ tRC (min)
120
2
2
Self Refresh Current
CKE ≤ 0.2V
Note: 1. Measured with outputs open. Addresses are changed only one time during tCC(min).
2. Refresh period is 64ms. Addresses are changed only one time during tCC(min).
PRELIMINARY (February, 2008, Version 0.1)
6
AMIC Technology, Corp.
A43L1632A
AC Operating Test Conditions
(VDD = 3.3V ±0.3V, TA = 0°C to +70°C or TA = -40ºC to +85ºC)
Parameter
Value
AC input levels
VIH/VIL = 2.4V/0.4V
1.4V
Input timing measurement reference level
Input rise and all time (See note3)
Output timing measurement reference level
Output load condition
tr/tf = 1ns/1ns
1.4V
See Fig.2
2.5V
V
V
OH(DC) = 2.0V, IOH = -1mA
OL(DC) = 0.4V, IOL = 1mA
VTT =1.05V
1200
Ω
50
Ω
Output
ZO=50Ω
OUTPUT
30pF
870
Ω
30pF
(Fig. 2) AC Output Load Circuit
(Fig. 1) DC Output Load Circuit
PRELIMINARY (February, 2008, Version 0.1)
7
AMIC Technology, Corp.
A43L1632A
AC Characteristics
(AC operating conditions unless otherwise noted)
-6
-7
Symbol
Parameter
Unit
Note
Min
6
Max
Min
Max
CAS Latency=3
7
10
-
1000
1000
ns
ns
1
tCC
CLK cycle time
CAS Latency=2
CAS Latency=3
CAS Latency=2
10
-
5.5
5.5
CLK to valid
output delay
tSAC
tOH
tCH
1,2
-
6
-
6
Output data hold time
CAS Latency=3
CAS Latency=2
2
-
-
2
-
-
ns
ns
2
3
2.5
3
3
CLK high pulse
width
-
3
-
CLK low pulse CAS Latency=3
width
2.5
3
-
3
-
tCL
tSS
ns
ns
3
3
CAS Latency=2
-
3
-
Input setup
time
CAS Latency=3
CAS Latency=2
1.5
2.5
1
-
1.75
2.5
1
-
-
-
tSH
Input hold time
-
-
ns
ns
3
2
tSLZ
CLK to output in Low-Z
1
-
1
-
CAS Latency=3
CAS Latency=2
-
5.5
6
-
5.5
6
CLK to output
in Hi-Z
tSHZ
ns
-
-
-
Note : 1. Parameters depend on programmed CAS latency.
2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter.
3. Assumed input rise and fall time (tr & tf) = 1ns.
If tr & tf is longer than 1ns, transient time compensation should be considered,
i.e., [(tr + tf)/2-1]ns should be added to the parameter.
PRELIMINARY (February, 2008, Version 0.1)
8
AMIC Technology, Corp.
A43L1632A
Operating AC Parameter
(AC operating conditions unless otherwise noted)
Version
Symbol
Parameter
Unit
Note
-6
-7
tRRD(min)
tRCD(min)
Row active to row active delay
2
CLK
CLK
1
1
3
3
RAS to
delay
CAS
tRP(min)
tRAS(min)
tRAS(max)
tRC(min)
Row precharge time
Row active time
3
7
3
7
CLK
CLK
μs
1
1
100
Row cycle time
10
10
CLK
1
tRDL(min)
tCDL(min)
tBDL(min)
tCCD(min)
Last data in to row precharge
Last data in to new col. Address delay
Last data in to burst stop
2
1
1
1
2
1
CLK
CLK
CLK
CLK
2
2
2
3
Col. Address to col. address delay
CAS Latency = 3
CAS Latency = 2
Number of valid output
data
ea
4
Note: 1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time and
then rounding off to the next higher integer.
2. Minimum delay is required to complete write.
3. All parts allow every cycle column address change.
4. In case of row precharge interrupt, auto precharge and read burst stop.
PRELIMINARY (February, 2008, Version 0.1)
9
AMIC Technology, Corp.
A43L1632A
Simplified Truth Table
Command
CKEn-1 CKEn CS RAS
DQM BA0 A10 A9~A0
BA1 /AP
Notes
CAS
L
WE
L
Register
Refresh
Mode Register Set
H
H
X
L
L
X
OP CODE
1,2
3
3
3
Auto Refresh
Self
H
L
L
L
L
L
H
H
X
X
Entry
Exit
H
H
Refresh
L
H
X
X
X
X
H
L
X
L
X
H
X
H
3
Bank Active & Row Addr.
H
V
V
Row Addr.
Column
Address
(A0~A7)
Read & Column Auto Precharge Disable
L
4
H
X
L
H
L
H
X
Address
Auto Precharge Enable
H
4,5
Column
Address
(A0~A7)
Write &
Auto Precharge Disable
Auto Precharge Enable
L
4
H
H
H
X
X
X
L
L
L
H
H
L
L
H
H
L
L
L
X
X
X
V
Column Address
H
4,5
Burst Stop
Precharge
X
6
Bank Selection
Both Banks
V
X
L
X
H
H
L
X
V
X
X
H
X
V
X
X
V
X
V
X
X
H
X
V
X
V
X
X
H
X
V
Entry
H
L
L
H
L
X
X
X
Clock Suspend or
Active Power Down
X
X
Exit
X
H
L
Entry
H
Precharge Power Down Mode
H
L
Exit
L
H
H
H
X
X
V
X
DQM
X
X
7
H
L
X
V
X
V
No Operation Command
(V = Valid, X = Don’t Care, H = Logic High, L = Logic Low)
Note : 1. OP Code: Operand Code
A0~A10, BA0, BA1: Program keys. (@MRS)
2. MRS can be issued only when all banks are at precharge state.
A new command can be issued after 2 clock cycle of MRS.
3. Auto refresh functions is same as CBR refresh of DRAM.
The automatical precharge without Row precharge command is meant by “Auto”.
Auto/Self refresh can be issued only when all banks are at precharge state.
4. BA0, BA1 : Bank select address.
If both BA1 and BA0 are “Low” at read, write, row active and precharge, bank A is selected.
If both BA1 is “Low” and BA0 is “High” at read, write, row active and precharge, bank B is selected.
If both BA1 is “High” and BA0 is “Low” at read, write, row active and precharge, bank C is selected.
If both BA1 and BA0 are “High” at read, write, row active and precharge, bank D is selected.
If A10/AP is “High” at row precharge, BA1 and BA0 is ignored and all banks are selected.
5. During burst read or write with auto precharge, new read/write command cannot be issued.
Another bank read/write command can be issued at every burst length.
6. Burst stop command is valid at every burst length.
7. DQM sampled at positive going edge of a CLK masks the data-in at the very CLK (Write DQM latency is 0)
but masks the data-out Hi-Z state after 2 CLK cycles. (Read DQM latency is 2)
PRELIMINARY (February, 2008, Version 0.1)
10
AMIC Technology, Corp.
A43L1632A
Mode Register Filed Table to Program Modes
Register Programmed with MRS
Address
BA0~ BA1
A10/AP
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
Function
RFU
RFU
W.B.L
TM
CAS Latency
BT
Burst Length
(Note 3)
(Note 2)
(Note 1)
Test Mode
CAS Latency
A6 A5 A4 Latency
Burst Type
Burst Length
A8 A7
Type
Mode Register Set
Vendor
A3
Type
A2 A1 A0
BT=0
BT=1
0
0
1
0
1
0
0
0
0
0
0
1
0
1
0
Reserved
0
1
Sequential
Interleave
0
0
0
0
0
1
0
1
0
1
2
4
1
2
4
1
2
Use
Only
1
1
0
1
1
1
1
1
0
0
1
1
1
0
1
0
1
3
0
1
1
1
1
1
0
0
1
1
1
0
1
0
1
8
8
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
256(Full)
Reserved
Reserved
Reserved
Reserved
Write Burst Length
Length
A9
0
Burst
1
Single Bit
Note : 1. RFU(Reserved for Future Use) should stay “0” during MRS cycle.
2. If A9 is high during MRS cycle, “Burst Read Single Bit Write” function will be enabled.
3. BA0, BA1 must be 0,0 to select the Mode Register.
PRELIMINARY (February, 2008, Version 0.1)
11
AMIC Technology, Corp.
A43L1632A
Power Up Sequence
1. Apply power and start clock, Attempt to maintain CKE = “H”, DQM = “H” and the other pins are NOP condition at inputs.
2. Maintain stable power, stable clock and NOP input condition for a minimum of 200μs.
3. Issue precharge commands for all banks of the devices.
4. Issue 2 or more auto-refresh commands.
5. Issue a mode register set command to initialize the mode register.
cf.) Sequence of 4 & 5 may be changed.
The device is now ready for normal operation.
Burst Sequence (Burst Length = 4)
Initial address
Sequential
Interleave
A1
0
A0
0
0
1
2
3
1
2
3
0
2
3
0
1
3
0
1
2
0
1
2
3
1
0
3
2
2
3
2
1
0
0
1
3
0
1
1
0
1
1
Burst Sequence (Burst Length = 8)
Initial address
Sequential
Interleave
A2
A1
A0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
2
3
4
5
6
7
1
2
3
4
5
6
7
0
2
3
4
5
6
7
0
1
3
4
5
6
7
0
1
2
4
5
6
7
0
1
2
3
5
6
7
0
1
2
3
4
5
7
0
1
2
3
4
5
6
7
1
2
3
0
1
6
7
4
5
3
2
1
0
7
6
5
4
4
5
6
7
0
1
2
3
5
4
7
6
1
0
3
2
6
7
4
5
2
3
0
1
7
6
5
4
3
2
1
0
6
7
0
1
2
3
4
0
1
2
3
4
5
6
0
3
2
5
4
7
6
PRELIMINARY (February, 2008, Version 0.1)
12
AMIC Technology, Corp.
A43L1632A
Device Operations
Clock (CLK)
command decoder so that
address inputs are ignored.
,
and
, and all the
WE
RAS CAS
Power-Up
The clock input is used as the reference for all SDRAM
operations. All operations are synchronized to the positive
going edge of the clock. The clock transitions must be
monotonic between VIL and VIH. During operation with CKE
high all inputs are assumed to be in valid state (low or high)
for the duration of set up and hold time around positive edge
of the clock for proper functionality and ICC specifications.
The following sequence is recommended for POWER UP
1. Power must be applied to either CKE and DQM inputs to
pull them high and other pins are NOP condition at the
inputs before or along with VDD (and VDDQ) supply.
The clock signal must also be asserted at the same time.
2. After VDD reaches the desired voltage, a minimum pause
of 200 microseconds is required with inputs in NOP
condition.
Clock Enable (CLK)
The clock enable (CKE) gates the clock onto SDRAM. If CKE
goes low synchronously with clock (set-up and hold time
same as other inputs), the internal clock is suspended from
the next clock cycle and the state of output and burst address
is frozen as long as the CKE remains low. All other inputs are
ignored from the next clock cycle after CKE goes low. When
all banks are in the idle state and CKE goes low
synchronously with clock, the SDRAM enters the power down
mode from the next clock cycle. The SDRAM remains in the
power down mode ignoring the other inputs as long as CKE
remains low. The power down exit is synchronous as the
internal clock is suspended. When CKE goes high at least
“tSS + 1 CLOCK” before the high going edge of the clock, then
the SDRAM becomes active from the same clock edge
accepting all the input commands.
3. All banks must be precharged now.
4. Perform a minimum of 2 Auto refresh cycles to stabilize the
internal circuitry.
5. Perform a MODE REGISTER SET cycle to program the
CAS latency, burst length and burst type as the default
value of mode register is undefined.
At the end of one clock cycle from the mode register set
cycle, the device is ready for operation.
When the above sequence is used for Power-up, all the
out-puts will be in high impedance state. The high
impedance of outputs is not guaranteed in any other
power-up sequence.
cf.) Sequence of 4 & 5 may be changed.
Mode Register Set (MRS)
The mode register stores the data for controlling the various
operation modes of SDRAM. It programs the CAS latency,
addressing mode, burst length, test mode and various vendor
specific options to make SDRAM useful for variety of different
applications. The default value of the mode register is not
defined, therefore the mode register must be written after
power up to operate the SDRAM. The mode register is
Bank Select (BA0, BA1)
This SDRAM is organized as 4 independent banks of
524,288 words X 32 bits memory arrays. The BA0, BA1
inputs is latched at the time of assertion of
and
CAS
RAS
to select the bank to be used for the operation. The bank
select BA0, BA1 is latched at bank activate, read, write mode
register set and precharge operations.
written by asserting low on
,
,
,
(The
WE
CS RAS CAS
SDRAM should be in active mode with CKE already high
prior to writing the mode register). The state of address pins
A0~A10, BA0 and BA1 in the same cycle as
Address Input (A0 ~ A10)
The 19 address bits required to decode the 524,288 word
locations are multiplexed into 11 address input pins
,
,
,
going low is the data written in the
WE
CAS
CS RAS
mode register. One clock cycle is required to complete the
write in the mode register. The mode register contents can
be changed using the same command and clock cycle
requirements during operation as long as all banks are in the
idle state. The mode register is divided into various fields
depending on functionality. The burst length field uses
A0~A2, burst type uses A3, addressing mode uses A4~A6,
A7~A8, A10, BA0 and BA1 are used for vendor specific
options or test mode. And the write burst length is
programmed using A9. A7~A8, A10, BA0 and BA1 must be
set to low for normal SDRAM operation.
(A0~A10). The 11 bit row address is latched along with
,
RAS
BA0 and BA1 during bank activate command. The 8 bit
column address is latched along with
BA1during read or write command.
,
, BA0 and
WE
CAS
NOP and Device Deselect
When
,
and
are high, the SDRAM performs
WE
RAS CAS
no operation (NOP). NOP does not initiate any new
operation, but is needed to complete operations which
require more than single clock like bank activate, burst read,
auto refresh, etc. The device deselect is also a NOP and is
Refer to table for specific codes for various burst length,
addressing modes and CAS latencies. BA0 and BA1 have to
be set to “0” to enter the Mode Register.
entered by asserting
high.
high disables the
CS
CS
PRELIMINARY (February, 2008, Version 0.1)
13
AMIC Technology, Corp.
A43L1632A
cycle as the burst write command. The input buffer is
deselected at the end of the burst length, even though the
internal writing may not have been completed yet. The burst
write can be terminated by issuing a burst read and DQM for
blocking data inputs or burst write in the same or the other
active bank. The burst stop command is valid only at full
page burst length where the writing continues at the end of
burst and the burst is wrap around. The write burst can also
be terminated by using DQM for blocking data and
precharging the bank “tRDL” after the last data input to be
written into the active row. See DQM OPERATION also.
Device Operations (continued)
Bank Activate
The bank activate command is used to select a random row
in an idle bank. By asserting low on
and
with
CS
RAS
desired row and bank addresses, a row access is initiated.
The read or write operation can occur after a time delay of
tRCD(min) from the time of bank activation. tRCD(min) is an
internal timing parameter of SDRAM, therefore it is
dependent on operating clock frequency. The minimum
number of clock cycles required between bank activate and
read or write command should be calculated by dividing
tRCD(min) with cycle time of the clock and then rounding off
the result to the next higher integer. The SDRAM has 4
internal banks on the same chip and shares part of the
internal circuitry to reduce chip area, therefore it restricts the
activation of all banks simultaneously. Also the noise
generated during sensing of each bank of SDRAM is high
requiring some time for power supplies to recover before the
other bank can be sensed reliably. tRRD(min) specifies the
minimum time required between activating different banks.
The number of clock cycles required between different bank
activation must be calculated similar to tRCD specification. The
minimum time required for the bank to be active to initiate
sensing and restoring the complete row of dynamic cells is
determined by tRAS(min) specification before a precharge
command to that active bank can be asserted. The maximum
time any bank can be in the active state is determined by
tRAS(max). The number of cycles for both tRAS(min) and
tRAS(max) can be calculated similar to tRCD specification.
DQM Operation
The DQM is used to mask input and output operation. It
works similar to
during read operation and inhibits writing
OE
during write operation. The read latency is two cycles from
DQM and zero cycle for write, which means DQM masking
occurs two cycles later in the read cycle and occurs in the
same cycle during write cycle. DQM operation is
synchronous with the clock, therefore the masking occurs for
a complete cycle. The DQM signal is important during burst
interrupts of write with read or precharge in the SDRAM. Due
to asynchronous nature of the internal write, the DQM
operation is critical to avoid unwanted or incomplete writes
when the complete burst write is not required.
Precharge
The precharge operation is performed on an active bank by
asserting low on
,
,
and A10/AP with valid BA
WE
CS RAS
of the bank to be precharged. The precharge command can
be asserted anytime after tRAS(min) is satisfied from the bank
activate command in the desired bank. “tRP” is defined as the
minimum time required to precharge a bank.
Burst Read
The burst read command is used to access burst of data on
consecutive clock cycles from an active row in an active
bank. The burst read command is issued by asserting low on
The minimum number of clock cycles required to complete
row precharge is calculated by dividing “tRP” with clock cycle
time and rounding up to the next higher integer. Care should
be taken to make sure that burst write is completed or DQM
is used to inhibit writing before precharge command is
asserted. The maximum time any bank can be active is
specified by tRAS(max). Therefore, each bank has to be
precharged within tRAS(max) from the bank activate
command. At the end of precharge, the bank enters the idle
state and is ready to be activated again.
and
with
being high on the positive edge of
WE
CS
CAS
the clock. The bank must be active for at least tRCD(min)
before the burst read command is issued. The first output
appears CAS latency number of clock cycles after the issue
of burst read command. The burst length, burst sequence
and latency from the burst read command is determined by
the mode register which is already programmed. The burst
read can be initiated on any column address of the active
row. The address wraps around if the initial address does not
start from a boundary such that number of outputs from each
I/O are equal to the burst length programmed in the mode
register. The output goes into high-impedance at the end of
the burst, unless a new burst read was initiated to keep the
data output gapless. The burst read can be terminated by
issuing another burst read or burst write in the same bank or
the other active bank or a precharge command to the same
bank. The burst stop command is valid at every page burst
length.
Entry to Power Down, Auto refresh, Self refresh and Mode
register Set etc, is possible only when all banks are in idle
state.
Auto Precharge
The precharge operation can also be performed by using
auto precharge. The SDRAM internally generates the timing
to satisfy tRAS(min) and “tRP” for the programmed burst length
and CAS latency. The auto precharge command is issued at
the same time as burst read or burst write by asserting high
on A10/AP. If burst read or burst write command is issued
with low on A10/AP, the bank is left active until a new
command is asserted. Once auto precharge command is
given, no new commands are possible to that particular bank
until the bank achieves idle state.
Burst Write
The burst write command is similar to burst read command,
and is used to write data into the SDRAM consecutive clock
cycles in adjacent addresses depending on burst length and
burst sequence. By asserting low on
,
and
with
WE
CS CAS
valid column address, a write burst is initiated. The data
inputs are provided for the initial address in the same clock
PRELIMINARY (February, 2008, Version 0.1)
14
AMIC Technology, Corp.
A43L1632A
preferred refresh mode when the SDRAM is being used for
normal data transactions. The auto refresh cycle can be
performed once in 15.6us or a burst of 4096 auto refresh
cycles once in 64ms.
All Banks Precharge
All banks can be precharged at the same time by using
Precharge all command. Asserting low on
,
and
CS RAS
with high on A10/AP after both banks have satisfied
WE
Self Refresh
tRAS(min) requirement, performs precharge on all banks. At
the end of tRP after performing precharge all, all banks are in
idle state.
The self refresh is another refresh mode available in the
SDRAM. The self refresh is the preferred refresh mode for
data retention and low power operation of SDRAM. In self
refresh mode, the SDRAM disables the internal clock and all
the input buffers except CKE. The refresh addressing and
timing is internally generated to reduce power consumption.
The self refresh mode is entered from all banks idle state by
Auto Refresh
The storage cells of SDRAM need to be refreshed every
64ms to maintain data. An auto refresh cycle accomplishes
refresh of a single row of storage cells. The internal counter
increments automatically on every auto refresh cycle to
refresh all the rows. An auto refresh command is issued by
asserting low on
,
,
and CKE with high on
CS RAS CAS
. Once the self refresh mode is entered, only CKE state
WE
being low matters, all the other inputs including clock are
ignored to remain in the self refresh.
asserting low on
,
and
with high on CKE and
CS RAS
CAS
. The auto refresh command can only be asserted with
WE
The self refresh is exited by restarting the external clock and
then asserting high on CKE. This must be followed by NOP’s
for a minimum time of “tRC” before the SDRAM reaches idle
state to begin normal operation. If the system uses burst auto
refresh during normal operation, it is recommended to used
burst 4096 auto refresh cycles immediately after exiting self
refresh.
all banks being in idle state and the device is not in power
down mode (CKE is high in the previous cycle). The time
required to complete the auto refresh operation is specified
by “tRC(min)”. The minimum number of clock cycles required
can be calculated by dividing “tRC” with clock cycle time and
then rounding up to the next higher integer. The auto refresh
command must be followed by NOP’s until the auto refresh
operation is completed. All banks will be in the idle state at
the end of auto refresh operation. The auto refresh is the
PRELIMINARY (February, 2008, Version 0.1)
15
AMIC Technology, Corp.
A43L1632A
Basic feature And Function Descriptions
1. CLOCK Suspend
1) Click Suspended During Write (BL=4)
2) Clock Suspended During Read (BL=4)
CLK
CMD
CKE
WR
RD
Masked by CKE
Masked by CKE
Internal
CLK
DQ(CL2)
DQ(CL3)
D0
D0
D1
D1
D2
D2
D3
D3
Q0
Q1
Q0
Q2
Q1
Q3
Q2
Q3
Not Written
Suspended Dout
Note: CLK to CLK disable/enable=1 clock
2. DQM Operation
2) Read Mask (BL=4)
1) Write Mask (BL=4)
CLK
CMD
WR
RD
DQM
Masked by CKE
D3
Masked by CKE
Q2
Hi-Z
Hi-Z
DQ(CL2)
DQ(CL3)
D0
D0
D1
D1
Q0
Q3
Q2
D3
Q1
Q3
DQM to Data-in Mask = 0CLK
DQM to Data-out Mask = 2
2) Read Mask (BL=4)
CLK
CMD
CKE
RD
DQM
Hi-Z
Hi-Z
Hi-Z
Hi-Z
Hi-Z
Q0
Q2
Q1
Q4
Q3
Q6
Q5
Q7
Q6
Q8
Q7
DQ(CL2)
DQ(CL3)
Hi-Z
* Note : 1. DQM makes data out Hi-Z after 2 clocks which should masked by CKE “L”.
2. DQM masks both data-in and data-out.
PRELIMINARY (February, 2008, Version 0.1)
16
AMIC Technology, Corp.
A43L1632A
3. CAS Interrupt (I)
1) Read interrupted by Read (BL=4)Note 1
CLK
CMD
RD
A
RD
B
ADD
DQ(CL2)
DQ(CL3)
QA0 QB0 QB1 QB2 QB3
QA0 QB0 QB1 QB2 QB3
t
CCD
Note2
2) Write interrupted by Write (BL =2)
3) Write interrupted by Read (BL =2)
CLK
WR WR
WR
RD
CMD
t
CCD
tCCD
Note2
Note2
ADD
DQ
A
B
A
B
DA0 DB0 DB1
DQ(CL2)
DQ(CL3)
DA0
QB0 QB1
t
CDL
Note3
DA0
QB0 QB1
t
CDL
Note3
Note : 1. By “Interrupt”, It is possible to stop burst read/write by external command before the end of burst.
By “ Interrupt”, to stop burst read/write by access; read, write and block write.
CAS
2. tCCD :
CAS
to
delay. (=1CLK)
CAS
CAS
3. tCDL : Last data in to new column address delay. (= 1CLK).
PRELIMINARY (February, 2008, Version 0.1)
17
AMIC Technology, Corp.
A43L1632A
4. CAS Interrupt (II) : Read Interrupted Write & DQM
(1) CL=2, BL=4
CLK
i) CMD
RD
RD
WR
D0
DQM
DQ
ii) CMD
D1
D2
D3
D2
WR
DQM
DQ
Hi-Z
D0
D1
D3
D2
D1
RD
RD
WR
iii) CMD
DQM
DQ
Hi-Z
D0
D1
D3
D2
iv) CMD
WR
DQM
DQ
Hi-Z
Note 1
Q0
D0
D3
(2) CL=3, BL=4
CLK
i) CMD
DQM
RD
RD
RD
RD
WR
D0
DQ
D1
D2
D3
D2
ii) CMD
WR
DQM
DQ
D0
D1
D3
D2
iii) CMD
WR
DQM
DQ
D0
D1
D3
D2
D1
iv) CMD
WR
DQM
DQ
Hi-Z
D0
D1
D3
D2
v) CMD
RD
WR
DQM
DQ
Hi-Z
Q0
D0
D3
Note 2
* Note : 1. To prevent bus contention, there should be at least one gap between data in and data out.
2. To prevent bus contention, DQM should be issued which makes a least one gap between data in and data out.
PRELIMINARY (February, 2008, Version 0.1)
18
AMIC Technology, Corp.
A43L1632A
5. Write Interrupted by Precharge & DQM
CLK
Note 2
CMD
WR
D0
PRE
Note 1
DQM
DQ
D1
D2 D3
Masked by DQM
Note : 1. To prevent bus contention, DQM should be issued which makes at least one gap between data in and data out.
2. To inhibit invalid write, DQM should be issued.
3. This precharge command and burst write command should be of the same bank, otherwise it is not precharge interrupt
but only another bank precharge of four banks operation.
4. For -6/7, tRDL=1CLK product can be supported within restricted amounts and it will be distinguished by bucket code
“NV” from the next generation, tRDL will be only 2CLK for every clock frequency.
6. Precharge
1 ) N o rm a l W rite (B L = 4 )
C L K
C M D
D Q
W R
D 0
P R E
D 1
D 2
D 3
tR D L
2 ) R e a d (B L = 4 )
C L K
C M D
R D
P R E
Q 2
D Q (C L 2 )
Q 0
Q 1
Q 0
Q 3
Q 2
D Q (C L 3 )
Q 1
Q 3
7. Auto Precharge
1) Normal Write (BL=4)
CLK
CMD
DQ
WR
D0
D1
D2
D3
Note 1
Auto Precharge Starts
2) Read (BL=4)
CLK
CMD
DQ(CL2)
DQ(CL3)
RD
Q0
Q1
Q0
Q2
Q1
Q3
Q2
Q3
Note 1
Auto Precharge Starts
* Note : 1. tRDL : Last data in to row precharge delay.
2. Number of valid output data after row precharge : 1, 2 for
Latency = 2, 3 respectively.
CAS
3. The row active command of the precharge bank can be issued after tRP from this point.
The new read/write command of other activated bank can be issued from this point.
At burst read/write with auto precharge,
interrupt of the same/another bank is illegal.
CAS
4. For -6/7, tRDL=1CLK product can be supported within restricted amounts and it will be distinguished by bucket code
“NV” from the next generation, tRDL will be only 2CLK for every clock frequency.
PRELIMINARY (February, 2008, Version 0.1)
19
AMIC Technology, Corp.
A43L1632A
8. Burst Stop & Interrupted by Precharge
1) Normal Write (BL=4)
CLK
2) Write Burst Stop (BL=8)
CLK
CMD
CMD
WR
PRE
WR
STOP
DQM
DQ
DQM
DQ
D0
D1
D2
D3
D0
D1
D2
D3
D4
D5
tRDL Note 1
t
BDL Note 2
1) Read Interrupted by Precharge (BL=4)
CLK
4) Read Burst Stop (BL=4)
CLK
CMD
CMD
RD
PRE
Q0
RD
STOP
Q0
Note 3
1
1
DQ(CL2)
DQ(CL3)
Q1
Q0
DQ(CL2)
DQ(CL3)
Q1
Q0
2
2
Q1
Q1
9. MRS
Mode Register Set
CLK
Note 1
PRE
MRS
ACT
CMD
t
RP
2CLK
Note : 1. tRDL: 1CLK
2. tBDL: 1CLK; Last data in to burst stop delay.
Read or write burst stop command is valid at every burst length.
3. Number of valid output data after row precharge or burst stop: 1,2 for CAS latency = 2, 3 respectively.
4. PRE: All banks precharge if necessary.
MRS can be issued only when all banks are in precharged state.
5. For -6/7, tRDL=1CLK product can be supported within restricted amounts and it will be distinguished by bucket
code “NV” from the next generation, tRDL will be only 2CLK for every clock frequency.
PRELIMINARY (February, 2008, Version 0.1)
20
AMIC Technology, Corp.
A43L1632A
10. Clock Suspend Exit & Power Down Exit
1) Clock Suspend (=Active Power Down) Exit
CLK
2) Power Down (=Precharge Power Down) Exit
CLK
CKE
CKE
t
SS
t
SS
Note 2
Note 1
Internal
CLK
Internal
CLK
NOP
ACT
RD
CMD
CMD
11. Auto Refresh & Self Refresh
Note 3
1) Auto Refresh
CLK
Note 4
Note 5
CKE
PRE
Internal
CLK
AR
CMD
CMD
t
RP
tRC
Note 6
2) Self Refresh
CLK
Note 4
CMD
CKE
PRE
SR
CMD
t
RP
tRC
* Note : 1. Active power down : one or more bank active state.
2. Precharge power down : both bank precharge state.
3. The auto refresh is the same as CBR refresh of conventional DRAM.
No precharge commands are required after Auto Refresh command.
During tRC from auto refresh command, other command can not be accepted.
4. Before executing auto/self refresh command, both banks must be idle state.
5. MRS, Bank Active, Auto/Self Refresh, Power Down Mode Entry.
6. During self refresh mode, refresh interval and refresh operation are performed internally.
After self refresh entry, self refresh mode is kept while CKE is LOW.
During self refresh mode, all inputs expect CKE will be don’t cared, and outputs will be in Hi-Z state.
During tRC from self refresh exit command, any other command can not be accepted.
Before/After self refresh mode, burst auto refresh cycle (4K cycles ) is recommended.
PRELIMINARY (February, 2008, Version 0.1)
21
AMIC Technology, Corp.
A43L1632A
12. About Burst Type Control
At MRS A3=”0”. See the BURST SEQUENCE TABE.(BL=4,8)
BL=1,2,4,8 and full page wrap around.
At MRS A3=” 1”. See the BURST SEQUENCE TABE.(BL=4,8)
BL=4,8 At BL=1,2 Interleave Counting = Sequential Counting
Sequential counting
Basic
MODE
Interleave counting
Every cycle Read/Write Command with random column address can realize
Random Column Access.
That is similar to Extended Data Out (EDO) Operation of convention DRAM.
Random
MODE
Random column Access
tCCD = 1 CLK
13. About Burst Length Control
At MRS A2,1,0 = “000”.
At auto precharge, tRAS should not be violated.
1
Basic
MODE
At MRS A2,1,0 = “001”.
At auto precharge, tRAS should not be violated.
2
4
8
At MRS A2,1,0 = “010”
At MRS A2,1,0 = “011”.
At MRS A9=”1”.
Read burst = 1,2,4,8, full page/write Burst =1
At auto precharge of write, tRAS should not be violated.
Special
BRSW
MODE
Before the end of burst, Row precharge command of the same bank
Stops read/write burst with Row precharge.
tRDL= 2 with DQM, valid DQ after burst stop is 1,2 for CL=2,3 respectively
Interrupt
RAS
(Interrupted by Precharge)
Interrupt
MODE
During read/write burst with auto precharge,
interrupt cannot be issued.
RAS
Before the end of burst, new read/write stops read/write burst and starts new
read/write burst or block write.
Interrupt
CAS
During read/write burst with auto precharge,
interrupt can not be issued.
CAS
PRELIMINARY (February, 2008, Version 0.1)
22
AMIC Technology, Corp.
A43L1632A
Power On Sequence for Low Power SDRAM
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
CS
High level is necessary
tRP
tRC
RAS
CAS
WE
ADDR
BA0, BA1
A10/AP
KEY
Ra
BS
Ra
High-Z
DQ
DQM
High level is necessary
Precharge
(All Banks)
Auto Refresh
Auto Refresh
Mode Regiser Set
Row Active
(A-Bank)
: Don't care
PRELIMINARY (February, 2008, Version 0.1)
23
AMIC Technology, Corp.
A43L1632A
Single Bit Read-Write-Read Cycles (Same Page) @CAS Latency=3, Burst Length=1
tCH
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
tCL
tCC
High
tRAS
tRC
tSH
*Note 1
CS
tSS
tRCD
tRP
tSH
RAS
tSS
tCCD
tSH
CAS
WE
tSS
tSH
tSS
tSS
tSH
ADDR
Ra
Ca
Cb
Cc
Rb
tSS
tSH
*Note 2,3
*Note 2,3
*Note 2,3 *Note 4
*Note 2
*Note 2
BA0, BA1
BA
BA
BA
BA
BA
BA
*Note 3
*Note 3
*Note 3 *Note 4
A10/AP
DQ
Ra
Rb
tRAC
tSH
tSH
tSAC
tSLZ
Qa
Db
Qc
tSS
tOH
tSHZ
tSS
DQM
Read
Write
Row Active
Read
Row Active
Precharge
: Don't care
PRELIMINARY (February, 2008, Version 0.1)
24
AMIC Technology, Corp.
A43L1632A
* Note : 1. All inputs can be don’t care when
is high at the CLK high going edge.
CS
2. Bank active & read/write are controlled by BA0, BA1.
BA1
BA0
Active & Read/Write
Bank A
0
0
1
1
0
1
0
1
Bank B
Bank C
Bank D
3. Enable and disable auto precharge function are controlled by A10/AP in read/write command.
A10/AP BA1
BA0
0
Operation
0
0
Disable auto precharge, leave bank A active at end of burst.
Disable auto precharge, leave bank B active at end of burst.
Disable auto precharge, leave bank C active at end of burst.
Disable auto precharge, leave bank D active at end of burst.
Enable auto precharge, precharge bank A at end of burst.
Enable auto precharge, precharge bank B at end of burst.
Enable auto precharge, precharge bank C at end of burst.
Enable auto precharge, precharge bank D at end of burst.
1
0
1
0
1
0
0
1
0
1
1
1
0
1
1
4. A10/AP and BA0, BA1 control bank precharge when precharge command is asserted.
A10/AP
BA1
0
BA0
0
Precharge
Bank A
0
0
0
0
1
0
1
Bank B
1
0
Bank C
1
1
Bank D
X
X
All Banks
PRELIMINARY (February, 2008, Version 0.1)
25
AMIC Technology, Corp.
A43L1632A
Read & Write Cycle at Same Bank @Burst Length=4
*Note : 1. Minimum row cycle times is required to complete internal DRAM operation.
2. Row precharge can interrupt burst on any cycle. [CAS latency-1] number of valid output data is available after Row
precharge. Last valid output will be Hi-Z(tSHZ) after the clock.
3. Output will be Hi-Z after the end of burst. (1, 2, 4, 8 & Full page bit burst)
PRELIMINARY (February, 2008, Version 0.1)
26
AMIC Technology, Corp.
A43L1632A
Page Read & Write Cycle at Same Bank @Burst Length=4, tRDL=2CLK
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
*Note 2
WE
ADDR
BA0
Ra
Ca
Cb
Cc
Cd
Rb
BA1
Ra
Rb
A10/AP
tRDL
DQ
(CL=2)
High-Z
Qa0
Qa1
Qb0
Qb1
Qb2
Dc0
Dc0
Dc1
Dd0
Dd0
Dd1
Dd1
tRCD
tDAL
*Note 4
DQ
(CL=3)
Qa0
Qa1
Qb0
Qb1
Dc1
High-Z
tCDL
*Note1
*Note3
*Note3
DQM
(CL=2)
*Note1
DQM
(CL=3)
Row Active
(A-Bank)
Write
(A-Bank)
Write
(A-Bank)
Read
(A-Bank)
Read
(A-Bank)
Precharge
(A-Bank)
Row Active
(A-Bank)
: Don't care
*Note : 1. To write data before burst read ends, DQM should be asserted three cycle prior to write command to avoid bus contention.
2. Row precharge will interrupt writing. Last data input, tRDL before Row precharge, will be written.
3. DQM should mask invalid input data on precharge command cycle when asserting precharge before end of burst. Input data
after Row precharge cycle will be masked internally.
4. tDAL, last data in to active delay, is tRDL + tRP.
PRELIMINARY (February, 2008, Version 0.1)
27
AMIC Technology, Corp.
A43L1632A
Read & Write Cycle at Different Bank @Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
WE
ADDR
BA0
RAa
CAa
RDd
CDb
RBc
CBc
BA1
A10/AP
RAa
RDb
RBc
tCDL
*Note 1
DQ
(CL=2)
QAa0 QAa1 QAa2 QAa3
DDb0 DDb1 DDb2 DDb3
DDb0 DDb1 DDb2 DDb3
QBc0 QBc1 QBc2
QBc0 QBc1
High-Z
High-Z
DQ
(CL=3)
QAa0 QAa1 QAa2 QAa3
DQM
(CL=2)
DQM
(CL=3)
Row Active
(A-Bank)
Read
(A-Bank)
Precharge
(A-Bank)
Write
(D-Bank)
Read
(B-Bank)
Row Active
(D-Bank)
Row Active
(B-Bank)
: Don't care
* Note : tCDL should be met to complete write.
PRELIMINARY (February, 2008, Version 0.1)
28
AMIC Technology, Corp.
A43L1632A
Read & Write Cycle with Auto Precharge @Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
WE
RAa
RBb
CAa
CBb
ADDR
BA0
BA1
RAa
RBb
A10/AP
DQ
(CL=2)
QAa0 QAa1 QAa2 QAa3
DDb0 DDb1 DDb2 DDb3
DDb0 DDb1 DDb2 DDb3
DQ
(CL=3)
QAa0 QAa1 QAa2 QAa3
DQM
Row Active
(A-Bank)
Auto Precharge
Start Point
(A-Bank/CL=3)
Auto Precharge
Start Point
(D-Bank)
Read with
Auto Precharge
(A-Bank)
Write with
Auto Precharge
(D-Bank)
Auto Precharge
Start Point
(A-Bank/CL=2)
Row Active
(D-Bank)
: Don't care
*Note : tRCD should be controlled to meet minimum tRAS before internal precharge start.
(In the case of Burst Length=1 & 2, BRSW mode)
PRELIMINARY (February, 2008, Version 0.1)
29
AMIC Technology, Corp.
A43L1632A
Clock Suspension & DQM Operation Cycle @CAS Latency=2, Burst Length=4
* Note : DQM is needed to prevent bus contention.
PRELIMINARY (February, 2008, Version 0.1)
30
AMIC Technology, Corp.
A43L1632A
Read Interrupted by Precharge & Read Burst Stop Cycle @Full Page Burst
* Note : 1. At full page mode, burst is finished by burst stop or precharge.
2. About the valid DQs after burst stop, it is same as the case of Precharge interrupt.
Both cases are illustrated above timing diagram. See the label A, B on them.
But at burst write, Burst stop and Precharge interrupt should be compared carefully.
Refer the timing diagram of “Full page write burst stop cycle”.
3. Burst stop is valid at every burst length.
PRELIMINARY (February, 2008, Version 0.1)
31
AMIC Technology, Corp.
A43L1632A
Write Interrupted by Precharge Command & Write Burst Stop Cycle @Full Page Bust, tRDL=2CLK
* Note : 1. At full page mode, burst is finished by burst stop or precharge.
2. Data-in at the cycle of interrupted by precharge cannot be written into the corresponding memory cell.
It is defined by AC parameter of tRDL.
DQM at write interrupted by precharge command is needed to prevent invalid write.
DQM should mask invalid input data on precharge command cycle when asserting precharge before end of burst.
Input data after Row precharge cycle will be masked internally.
3. Burst stop is valid at every burst length.
PRELIMINARY (February, 2008, Version 0.1)
32
AMIC Technology, Corp.
A43L1632A
Burst Read Single Bit Write Cycle @Burst Length=2
* Note : 1. BRSW mode is enabled by setting A9 “High” at MRS (Mode Register Set).
At the BRSW Mode, the burst length at write is fixed to “1” regardless of programed burst length.
2. When BRSW write command with auto precharge is executed, keep it in mind that tRAS should not be violated.
Auto precharge is executed at the burst-end cycle, so in the case of BRSW write command,
the next cycle starts the precharge.
PRELIMINARY (February, 2008, Version 0.1)
33
AMIC Technology, Corp.
A43L1632A
Active/Precharge Power Down Mode @CAS Latency=2, Burst Length=4
* Note : 1. All banks should be in idle state prior to entering precharge power down mode.
2. CKE should be set high at least “1CLK + tSS” prior to Row active command.
3. Cannot violate minimum refresh specification. (64ms)
PRELIMINARY (February, 2008, Version 0.1)
34
AMIC Technology, Corp.
A43L1632A
Self Refresh Entry & Exit Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
* Note 4
* Note 2
tRC min.
tSS
* Note 6
* Note 1
* Note 3
tSS
* Note 5
CS
RAS
CAS
* Note 7
* Note 7
WE
ADDR
BA1, BA0
A10/AP
DQ
High-Z
High-Z
DQM
Self Refresh Exit
Auto Refresh
Self Refresh Entry
: Don't care
* Note : TO ENTER SELF REFRESH MODE
1. with CKE should be low at the same clock cycle.
CS RAS CAS
,
&
2. After 1 clock cycle, all the inputs including the system clock can be don’t care except for CKE.
3. The device remains in self refresh mode as long as CKE stays “Low”.
(cf.) Once the device enters self refresh mode, minimum tRAS is required before exit from self refresh.
TO EXIT SELF REFRESH MODE
4. System clock restart and be stable before returning CKE high.
5.
starts from high.
CS
6. Minimum tRC is required after CKE going high to complete self refresh exit.
7. Before/After self refresh mode, AUTO REFRESH commands must be issued every 15.6μs or less as both SELF
REFRESH and AUTO REFRESH utilize the row refresh counter.
PRELIMINARY (February, 2008, Version 0.1)
35
AMIC Technology, Corp.
A43L1632A
Mode Register Set Cycle
Auto Refresh Cycle
0
1
2
3
4
5
6
0
1
2
3
4
5
6
7
8
9
10
CLOCK
CKE
High
High
*Note 2
CS
tRC
RAS
CAS
* Note 1
WE
* Note 3
Key
Ra
ADDR
DQ
Hi-Z
Hi-Z
DQM
MRS
Auto Refresh
New Command
: Don't care
New
Command
* All banks precharge should be completed before Mode Register Set cycle and auto refresh cycle.
MODE REGISTER SET CYCLE
* Note : 1.
,
,
&
activation at the same clock cycle with address key will set internal mode register.
WE
CS RAS CAS
2. Minimum 2 clock cycles is required before new
3. Please refer to Mode Register Set table.
activation.
RAS
PRELIMINARY (February, 2008, Version 0.1)
36
AMIC Technology, Corp.
A43L1632A
Function Truth Table (Table 1)
Current
CS RAS
BA
Address
Action
Note
CAS
WE
State
H
L
L
L
L
L
L
L
H
L
L
L
L
L
L
L
H
L
L
L
L
L
L
L
H
L
L
L
L
L
L
L
H
L
L
L
L
L
L
X
H
H
H
L
X
H
H
L
X
H
L
X
X
X
X
X
NOP
NOP
X
ILLEGAL
2
2
X
H
L
BA
BA
BA
X
CA, A10/AP ILLEGAL
IDLE
H
H
L
RA
A10/AP
X
Row Active; Latch Row Address
L
NOP
4
5
5
L
H
L
Auto Refresh or Self Refresh
L
L
OP Code
Mode Register Access
X
H
H
H
H
L
X
H
H
L
X
H
L
X
X
X
X
X
NOP
NOP
Row
X
ILLEGAL
2
2
Active
H
L
BA
BA
BA
BA
X
CA,A10/AP Begin Read; Latch CA; Determine AP
CA,A10/AP Begin Write; Latch CA; Determine AP
L
H
H
L
H
L
RA
PA
X
ILLEGAL
L
Precharge
L
X
X
H
L
ILLEGAL
X
H
H
H
H
L
X
H
H
L
X
X
NOP(Continue Burst to End →Row Active)
NOP(Continue Burst to End →Row Active)
Term burst →Row Active
X
X
X
X
H
L
BA
BA
BA
BA
X
CA,A10/AP Term burst; Begin Read; Latch CA; Determine AP
CA,A10/AP Term burst; Begin Write; Latch CA; Determine AP
3
3
2
3
Read
L
H
H
L
H
L
RA
ILLEGAL
L
A10/AP
Term Burst; Precharge timing for Reads
ILLEGAL
L
X
X
H
L
X
X
X
X
X
H
H
H
H
L
X
H
H
L
X
NOP(Continue Burst to End→Row Active)
NOP(Continue Burst to End→Row Active)
Term burst →Row Active
X
X
H
L
BA
BA
BA
BA
X
CA,A10/AP Term burst; Begin Read; Latch CA; Determine AP
CA,A10/AP Term burst; Begin Write; Latch CA; Determine AP
3
3
2
3
Write
L
H
H
L
H
L
RA
ILLEGAL
L
A10/AP
Term Burst; Precharge timing for Writes
ILLEGAL
L
X
X
H
L
X
X
X
X
X
H
H
H
H
L
X
H
H
L
X
NOP(Continue Burst to End→Precharge)
NOP(Continue Burst to End→Precharge)
ILLEGAL
X
Read with
Auto
Precharge
X
H
L
BA
BA
BA
X
CA,A10/AP ILLEGAL
CA,A10/AP ILLEGAL
2
2
L
H
L
X
X
RA, PA
X
ILLEGAL
ILLEGAL
L
2
PRELIMINARY (February, 2008, Version 0.1)
37
AMIC Technology, Corp.
A43L1632A
Function Truth Table (Table 1, Continued)
Current
CS
BS
Address
Action
Note
CAS
WE
RAS
State
H
L
L
L
L
L
L
H
L
L
L
L
L
L
H
L
L
L
L
L
L
H
L
L
L
L
H
X
H
H
H
H
L
X
H
H
L
X
H
L
X
X
X
X
X
NOP(Continue Burst to End→Precharge)
NOP(Continue Burst to End→Precharge)
ILLEGAL
Write with
Auto
X
H
L
BS
BS
BS
X
CA,A10/AP ILLEGAL
CA,A10/AP ILLEGAL
2
2
Precharge
L
H
L
X
X
X
H
L
RA, PA
ILLEGAL
L
X
X
X
X
ILLEGAL
2
X
H
H
H
L
X
H
H
L
X
NOP→Idle after tRP
NOP→Idle after tRP
ILLEGAL
X
X
Precharge
X
H
L
BS
BS
BS
X
CA,A10/AP ILLEGAL
2
2
2
4
H
H
L
RA
ILLEGAL
L
A10/AP
NOP→Idle after tRP
ILLEGAL
L
X
X
H
L
X
X
X
X
X
H
H
H
L
X
H
H
L
X
NOP→Row Active after tRCD
NOP→Row Active after tRCD
ILLEGAL
X
X
Row
Activating
X
H
L
BS
BS
BS
X
CA,A10/AP ILLEGAL
2
2
2
2
H
H
L
RA
ILLEGAL
L
A10/AP
ILLEGAL
L
X
X
X
X
X
X
X
X
X
X
X
X
X
X
ILLEGAL
X
H
H
L
X
H
L
X
NOP→Idle after tRC
NOP→Idle after tRC
ILLEGAL
X
Refreshing
X
H
L
X
ILLEGAL
L
X
ILLEGAL
X
X
X
NOP→Idle after 2 clocks
L
L
L
L
H
H
H
L
H
H
L
H
L
H
X
X
X
X
X
X
X
NOP→Idle after 2 clocks
ILLEGAL
Mode
Register
Accessing
X
X
ILLEGAL
X
ILLEGAL
Abbreviations
RA = Row Address
NOP = No Operation Command
BA = Bank Address
CA = Column Address
AP = Auto Precharge
PA = Precharge All
Note: 1. All entries assume that CKE was active (High) during the preceding clock cycle and the current clock cycle.
2. Illegal to bank in specified state: Function may be legal in the bank indicated by BA, depending on the state of that bank.
3. Must satisfy bus contention, bus turn around, and/or write recovery requirements.
4. NOP to bank precharging or in idle state. May precharge bank indicated by BA (and PA).
5. Illegal if any banks is not idle.
PRELIMINARY (February, 2008, Version 0.1)
38
AMIC Technology, Corp.
A43L1632A
Function Truth Table for CKE (Table 2)
Current
State
CKE CKE
CS
RAS
Address
Action
Note
CAS
WE
n-1
n
H
X
X
H
L
X
X
H
H
H
L
X
X
H
H
L
X
X
H
L
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
RA
X
INVALID
L
L
H
H
H
H
H
L
6
6
Exit Self Refresh→ABI after tRC
Exit Self Refresh→ABI after tRC
ILLEGAL
Self
L
L
Refresh
L
L
X
X
X
X
X
H
L
ILLEGAL
L
L
X
X
X
X
H
H
L
ILLEGAL
L
X
X
H
L
X
X
X
H
H
H
L
NOP(Maintain Self Refresh)
INVALID
H
L
X
H
H
H
H
H
L
7
7
Exit Power Down→ABI
Exit Power Down→ABI
ILLEGAL
Both
Bank
Precharge
Power
L
L
L
L
L
X
X
X
X
X
H
L
ILLEGAL
Down
L
L
X
X
X
X
H
H
L
ILLEGAL
L
X
X
H
L
X
X
X
H
H
H
L
NOP(Maintain Power Down Mode)
Refer to Table 1
Enter Power Down
Enter Power Down
ILLEGAL
H
H
H
H
H
H
H
H
L
H
L
8
8
L
All
Banks
Idle
L
L
L
L
X
H
H
L
ILLEGAL
L
L
H
L
Row (& Bank ) Active
Enter Self Refresh
L
L
L
8
L
L
L
L
OPCODE MRS
L
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
NOP
H
H
L
H
L
Refer to Operations in Table 1
Begin Clock Suspend next cycle
Exit Clock Suspend next cycle
Maintain clock Suspend
Any State
Other than
Listed
9
9
H
L
Above
L
Abbreviations : ABI = All Banks Idle
Note: 6. After CKE’s low to high transition to exit self refresh mode, a minimum of tRC(min) has to be elapse before issuing a new
command.
7. CKE low to high transition is asynchronous as if it restarts internal clock.
A minimum setup time “tSS + one clock” must be satisfied before any command can be issued other than exit.
8. Power-down and self refresh can be entered only when all the banks are in idle state.
9. Must be a legal command.
PRELIMINARY (February, 2008, Version 0.1)
39
AMIC Technology, Corp.
A43L1632A
Part Numbering Scheme
X
X XX X X X X X
XX
A43
Package Material
Blank: normal
F: PB free
Temperature
Blank :0°C ~ 70°C
I:-25°C ~ 85°C
U:-40°C ~ 85°C
Speed
95: 105 MHz
75: 133 MHz
7: 143 MHz
6: 166 MHz
55: 183 MHz
5: 200 MHz
Package Type
V: TSOP
G: CSP
Device Version*
Mobile Function*
I/O Width
16: 16 I/O
32: 32 I/O
Device Density
06: 1M
16: 2M
26: 4M
36: 8M
46: 16M
83: 256K
Operating Vcc
L: 3V~3.6V
P: 2.3V~2.7V
E: 1.7V~1.95V
Device Type
A43: AMIC SDRAM
* Optional
PRELIMINARY (February, 2008, Version 0.1)
40
AMIC Technology, Corp.
A43L1632A
Ordering Information
Part No.
Min. Cycle Time
(ns)
Max. Clock
Frequency (MHz)
Access Time
Package
A43L1632AV-6F
A43L1632AV-6UF
A43L1632AG-6F
A43L1632AG-6UF
A43L1632AV-7F
A43L1632AV-7UF
A43L1632AG-7F
A43L1632AG-7UF
86 Pin Pb-Free TSOP (II)
86 Pin Pb-Free TSOP (II)
90 ball Pb-Free CSP
6
166
6 ns
90 ball Pb-Free CSP
86 Pin Pb-Free TSOP (II)
86 Pin Pb-Free TSOP (II)
90 ball Pb-Free CSP
7
143
7 ns
90 ball Pb-Free CSP
Note: -U is for industrial operating temperature range -40ºC to +85ºC.
PRELIMINARY (February, 2008, Version 0.1)
41
AMIC Technology, Corp.
A43L1632A
Package Information
90LD STF BGA (8 x 13mm) Outline Dimensions
unit: mm
-A-
aaa
D
D
1
Pin #1
e
-B-
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
aaa
1 2 3 4 5 6 7 8 9
See Detail B
See Detail A
CAVITY
M
C
eee C A B
M
fff
// bbb C
B
A
b
-C-
ddd C
SOLDER BALL
1
2
SEATING PLANE
Detail A
Detail B
Dimensions in mm
Dimensions in inches
Symbol
Min
-
Nom
-
Max
1.40
0.40
0.94
0.40
8.10
13.10
-
Min
-
Nom
-
Max
0.055
0.016
0.037
0.016
0.319
0.516
-
A
A1
0.30
0.84
0.32
7.90
12.90
-
0.35
0.89
0.36
8.00
13.00
6.40
11.20
0.80
0.45
0.10
0.10
0.12
0.15
0.08
9/15
0.012
0.033
0.013
0.311
0.508
-
0.014
0.035
0.014
0.315
0.512
0.252
0.441
0.031
0.018
0.004
0.004
0.005
0.006
0.003
9/15
A2
c
D
E
D1
E1
-
-
-
-
e
-
-
-
-
b
0.40
0.50
0.016
0.020
aaa
bbb
ccc
ddd
eee
MD/ME
Notes:
1. PRIMARY DATUM C AND SEATING PLANE ARE DEFINED BY THE
SPHERICAL CROWNS OF THE SOLDER BALLS.
2. DIMENSION b IS MEASURED AT THE MAXIMUM SOLDER BALL
DIAMETER, PARALLEL TO PRIMARY DATUM C.
3. THERE SHALL BE A MINIMUM CLEARANCE OF 0.25mm BETWEEN
THE EDGE OF THE SOLDER BALL AND THE BODY EDGE.
4. REFERENCE DOCUMENT : JEDEC MO-205.
5. THE PATTERN OF PIN 1 FIDUCIAL IS FOR REFERENCE ONLY.
PRELIMINARY (February, 2008, Version 0.1)
42
AMIC Technology, Corp.
A43L1632A
Package Information
TSOP 86L (Type II) Outline Dimensions
unit: inches/mm
D
Detail "A"
86
44
c
1
43
R
1
0.21 REF
R2
0.665 REF
S
Gauge Plane
-C-
A1
-C-
θ
e
b
0.10
θ
1
Seating Plane
L
L
1
Detail "A"
Dimensions in inches
Dimensions in mm
Symbol
Min
-
Nom
Max
Min
Nom
Max
1.20
A
-
0.047
0.006
0.041
0.011
0.008
-
-
A1
A2
b
0.002
0.037
0.007
0.005
0.004
0.05
0.95
0.17
0.12
0.10
0.15
1.05
0.27
0.21
0.039
1.00
-
-
c
-
-
D
0.875 BSC
22.22 BSC
S
0.024 REF
0.61 REF
E
0.463 BSC
11.76 BSC
E1
e
0.400 BSC
10.16 BSC
0.020 BSC
0.50 BSC
L
0.016
0.020
0.024
0.40
0.50
0.60
L1
R1
R2
θ
0.031 REF
0.80 REF
0.005
0.005
0°
-
-
-
-
-
0.010
8°
0.12
0.12
0°
-
-
-
-
-
0.25
8°
0°
-
0°
-
θ1
Notes:
1. The maximum value of dimension D includes end flash.
2. Dimension E does not include resin fins.
3. Dimension S includes end flash.
PRELIMINARY (February, 2008, Version 0.1)
43
AMIC Technology, Corp.
相关型号：
©2020 ICPDF网 联系我们和版权申明