A43E06161V-95F [AMICC]
512K X 16 Bit X 2 Banks Synchronous DRAM; 512K ×16位×2组同步DRAM
| 型号： | A43E06161V-95F |
| 厂家： | 
AMIC TECHNOLOGY |
| 描述： | 512K X 16 Bit X 2 Banks Synchronous DRAM |
| 文件： | 总46页 (文件大小：1290K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
A43E06161
Preliminary
512K X 16 Bit X 2 Banks Synchronous DRAM
Document Title
512K X 16 Bit X 2 Banks Synchronous DRAM
Revision History
Rev. No. History
Issue Date
May 3, 2005
July 31, 2005
Remark
0.0
0.1
Initial issue
Preliminary
Modify tSS from 3ns to 2ns
Modify tSH from 1.5ns to 1ns
Modify ICC6 from 0.5mA to 200μA
PRELIMINARY (July, 2005, Version 0.1)
AMIC Technology, Corp.
A43E06161
Preliminary
512K X 16 Bit X 2 Banks Synchronous DRAM
Features
ꢀLow power supply
ꢀIndustrial operating temperature range: -40ºC to +85ºC
for –U
- VDD: 1.8V
- VDDQ: 1.8V
ꢀPb-Free type for -F
ꢀLVCMOS compatible with multiplexed address
ꢀBurst Read Single-bit Write operation
ꢀDQM for masking
ꢀAuto & self refresh
ꢀ32ms refresh period (2K cycle)
ꢀAvailable in 50-pin TSOP(II) package
ꢀDual banks / Pulse RAS
ꢀMRS cycle with address key programs
- CAS Latency (2,3)
- Burst Length (1,2,4,8 & full page)
- Burst Type (Sequential & Interleave)
ꢀAll inputs are sampled at the positive going edge of the
system clock
ꢀDeep Power Down Mode
ꢀClock Frequency: 105MHz @ CL=3 (-95)
133MHz @ CL=3 (-75)
General Description
The A43E06161 is 16,777,216 bits synchronous high data
rate Dynamic RAM organized as 2 X 524,288 words by 16
bits, fabricated with AMIC’s high performance CMOS
technology. Synchronous design allows precise cycle control
with the use of system clock. I/O transactions are possible on
every clock cycle. Range of operating frequencies,
programmable latencies allows the same device to be useful
for a variety of high bandwidth, high performance memory
system applications.
Pin Configuration
ꢀTSOP (II)
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26
A43E06161V
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
PRELIMINARY (July, 2005, Version 0.1)
1
AMIC Technology, Corp.
A43E06161
Block Diagram
LWE
Data Input Register
Bank Select
LDQM
512K X 16
512K X 16
CLK
DQi
Column Decoder
ADD
Latency & Burst Length
LRAS
Programming Register
LWCBR
LCAS
LDQM
LRAS
LCBR
LWE
Timing Register
L(U)DQM
CLK
CKE
CS
RAS
CAS
WE
PRELIMINARY (July, 2005, Version 0.1)
2
AMIC Technology, Corp.
A43E06161
Pin Descriptions
Symbol
Name
Description
CLK
CS
System Clock
Chip Select
Active on the positive going edge to sample all inputs.
Disables or Enables device operation by masking or enabling all inputs except CLK,
CKE and L(U)DQM
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one clock + tss prior to new command.
Disable input buffers for power down in standby.
CKE
Clock Enable
Row / Column addresses are multiplexed on the same pins.
Row address : RA0~RA10, Column address: CA0~CA7
Selects bank to be activated during row address latch time.
Selects band for read/write during column address latch time.
A0~A10/AP
BA
Address
Bank Select Address
Row Address Strobe
Latches row addresses on the positive going edge of the CLK with RAS low.
Enables row access & precharge.
RAS
CAS
Latches column addresses on the positive going edge of the CLK with CAS low.
Enables column access.
Column Address
Strobe
Write Enable
Enables write operation and Row precharge.
WE
Makes data output Hi-Z, t SHZ after the clock and masks the output.
Blocks data input when L(U)DQM active.
Data Input/Output
Mask
L(U)DQM
DQ0-15
Data Input/Output
Data inputs/outputs are multiplexed on the same pins.
Power
Supply/Ground
VDD/VSS
Power Supply: +1.7V~1.95V/Ground
Data Output
Power/Ground
VDDQ/VSSQ
NC/RFU
Provide isolated Power/Ground to DQs for improved noise immunity.
No Connection
PRELIMINARY (July, 2005, Version 0.1)
3
AMIC Technology, Corp.
A43E06161
Absolute Maximum Ratings*
*Comments
Voltage on any pin relative to VSS (Vin, Vout ) . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +2.6V
Voltage on VDD supply relative to VSS (VDD, VDDQ )
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +2.6V
Storage Temperature (TSTG) . . . . . . . . . . -55°C to +150°C
Soldering Temperature X Time (TSLODER) . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C X 10sec
Power Dissipation (PD) . . . . . . . . . . . . . . . . . . . . . . . 0.8W
Short Circuit Current (Ios) . . . . . . . . . . . . . . . . . . . . 50mA
Permanent device damage may occur if “Absolute Maximum
Ratings” are exceeded.
Functional operation should be restricted to recommended
operating condition.
Exposure to higher than recommended voltage for extended
periods of time could affect device reliability.
Capacitance (TA=25°C, f=1MHz)
Parameter
Input Capacitance
Symbol
CI1
Condition
Min
2.0
2.0
Typ
Max
4.0
Unit
pF
A0 to A10, BA
CLK, CKE,
CI2
4.0
pF
,
,
,
,
WE
CS RAS CAS
UDQM, LDQM
Data Input/Output Capacitance
CI/O
DQ0 to DQ15
3.5
6.0
pF
DC Electrical Characteristics
Recommend operating conditions (Voltage referenced to VSS = 0V, TA = -25ºC to +70ºC or -40ºC to +85ºC)
Parameter
Supply Voltage
Symbol
VDD
VDDQ
VIH
Min
Typ
Max
1.95
1.95
VDD+0.3
0.3
Unit
V
Note
1.7
1.8
DQ Supply Voltage
Input High Voltage
1.7
1.8
V
0.8 x VDDQ
-
0
-
V
Input Low Voltage
VIL
-0.3
V
Note 1
Output High Voltage
Output Low Voltage
Input Leakage Current
Output Leakage Current
Output Loading Condition
VOH
VDDQ-0.2
-
V
IOH = -0.1mA
IOL = 0.1mA
Note 2
VOL
-
-
0.2
V
IIL
-1
-
1
µA
µA
IOL
-1.5
-
1.5
Note 3
See Figure 1
Note: 1. VIL (min) = -1.5V AC (pulse width ≤ 5ns).
2. Any input 0V ≤ VIN ≤ VDD + 0.3V, all other pins are not under test = 0V
3. Dout is disabled, 0V ≤ Vout ≤ VDD
PRELIMINARY (July, 2005, Version 0.1)
4
AMIC Technology, Corp.
A43E06161
Decoupling Capacitance Guide Line
Recommended decoupling capacitance added to power line at board.
Parameter
Symbol
Value
Unit
µF
Decoupling Capacitance between VDD and VSS
Decoupling Capacitance between VDDQ and VSSQ
CDC1
CDC2
0.1 + 0.01
0.1 + 0.01
µF
Note: 1. VDD and VDDQ pins are separated each other.
All VDD pins are connected in chip. All VDDQ pins are connected in chip.
2. VSS and VSSQ pins are separated each other
All VSS pins are connected in chip. All VSSQ pins are connected in chip.
DC Electrical Characteristics
(Recommended operating condition unless otherwise noted, TA = 0 to 70°C or -40ºC to +85ºC)
Speed
CAS
Symbol
Parameter
Test Conditions
Unit Notes
Latency
-75
-95
Operating Current
(One Bank Active)
Burst Length = 1
Icc1
20
mA
mA
1
tRC ≥ tRC(min), tCC ≥ tCC(min), IOL = 0mA
Icc2 P
Precharge Standby
Current in power-
down mode
CKE ≤ VIL(max), tCC = 15ns
0.3
0.1
Icc2 PS
CKL ≤ VIL(max), tCC = ∞
CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 15ns
ICC2N
Precharge Standby
Current in non
power-down mode
5
2
Input signals are changed one time during 30ns
mA
CKE ≥ VIH(min), CLK ≤ VIL(max), tCC = ∞
Input signals are stable.
ICC2NS
ICC3 P
Active Standby
Current in power-
down mode
mA
mA
2
CKE ≤ VIL(max), tCC = 15ns
Active Standby
current in non
power-down mode
(One Bank Active)
CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 15ns
Input signals are changed one time during 30ns
10
ICC3N
ICC4
Operating Current
(Burst Mode)
IOL = 0mA, Page Burst
All bank Activated, tCCD = tCCD (min)
20
mA
1
2
ICC5
ICC6
Refresh Current
20
mA
tRC ≥ tRC (min)
CKE ≤ 0.2V
Self Refresh
Current
200
µA
Deep Power Down
Current
ICC7
CKE ≤ 0.2V
10
µA
Note: 1. Measured with outputs open. Addresses are changed only one time during tCC(min).
2. Refresh period is 32ms. Addresses are changed only one time during tCC(min).
PRELIMINARY (July, 2005, Version 0.1)
5
AMIC Technology, Corp.
A43E06161
AC Operating Test Conditions
(VDD = 1.8V ±0.3V, TA = 0°C to +70°C or -40ºC to +85ºC)
Parameter
AC input levels
Value
Unit
V
0.9 x VDDQ / 0.2
0.5 x VDDQ
tr / tf = 1 / 1
0.5 x VDDQ
See Fig.2
Input timing measurement reference level
Input rise and all time (See note3)
Output timing measurement reference level
Output load condition
V
ns
V
1.8V
VOH(DC) = VDDQ-0.2V, IOH = -0.1mA
VOL(DC) = 0.2V, IOL = 0.1mA
VTT = 0.5V x VDDQ
13.9Ω
50Ω
Output
ZO=50Ω
OUTPUT
30pF
10.6Ω
30pF
(Fig. 2) AC Output Load Circuit
(Fig. 1) DC Output Load Circuit
AC Characteristics
(AC operating conditions unless otherwise noted)
-75
-95
Symbol
Parameter
Unit
Note
Min
7.5
12
-
Max
Min
Max
CL=3
CL=2
CL=3
CL=2
9.5
15
-
tCC
CLK cycle time
1000
1000
ns
1
6
9
-
7
8
-
CLK to valid
Output delay
tSAC
tOH
tCH
ns
ns
ns
1,2
2
-
-
Output data hold time
2.5
3
2.5
3.5
3.5
3.5
3.5
2
CL=3
CL=2
CL=3
CL=2
CL=3
CL=2
-
-
CLK high pulse width
3
3
-
-
3
-
-
tCL
tSS
CLK low pulse width
Input setup time
ns
ns
3
3
3
-
-
2
-
-
2
-
2
-
tSH
Input hold time
1
-
1
-
ns
ns
3
2
tSLZ
CLK to output in Low-Z
1
-
1
-
CL=3
CL=2
-
6
8
-
7
8
tSHZ
CLK to output in Hi-Z
ns
-
-
CL=CAS Latency.
*All AC parameters are measured from half to half.
Note : 1. Parameters depend on programmed CAS latency.
2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter.
3. Assumed input rise and fall time (tr & tf) = 1ns.
If tr & tf is longer than 1ns, transient time compensation should be considered,
i.e., [(tr + tf)/2-1]ns should be added to the parameter.
PRELIMINARY (July, 2005, Version 0.1)
6
AMIC Technology, Corp.
A43E06161
Operating AC Parameter
(AC operating conditions unless otherwise noted)
Version
Symbol
Parameter
Unit
Note
-75
2
-95
2
tRRD(min)
tRCD(min)
Row active to row active delay
CLK
ns
1
1
27
28.5
RAS to
delay
CAS
tRP(min)
tRAS(min)
tRAS(max)
tRC(min)
Row precharge time
Row active time
27
57
28.5
57
ns
ns
µs
ns
1
1
100
Row cycle time
84
85.5
1
tCDL(min)
tRDL(min)
tBDL(min)
tCCD(min)
Last data in new col. Address delay
Last data in row precharge
7.5
2
8.5
2
ns
CLK
ns
2
1, 2
2
Last data in to burst stop
7.5
7.5
9.5
9.5
Col. Address to col. Address delay
ns
Note: 1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time and
then rounding off to the next higher integer.
2. Minimum delay is required to complete write.
3. All parts allow every cycle column address change.
PRELIMINARY (July, 2005, Version 0.1)
7
AMIC Technology, Corp.
A43E06161
Simplified Truth Table
Command
CKEn-1 CKEn CS RAS
DQM BA A10/ A9~A0
Notes
CAS
L
WE
L
AP
Register
Mode Register Set
Auto Refresh
1,2
H
H
X
L
L
X
X
OP CODE
3
3
3
Refresh
H
L
L
L
L
L
H
H
X
X
Entry
Self
H
H
Refresh
Exit
L
H
X
X
X
H
L
X
L
X
H
X
H
3
4
Bank Active & Row Addr.
H
V
V
Row Addr.
Read &
Column Addr.
Auto Precharge Disable
Auto Precharge Enable
Auto Precharge Disable
Auto Precharge Enable
L
H
L
Column
Addr.
4
H
X
L
H
L
H
X
4,5
4
Write &
Column
Addr.
H
H
X
X
L
L
H
H
L
L
L
X
X
V
Column Addr.
H
4,5
Burst Stop
Precharge
H
X
Bank Selection
Both Banks
V
X
L
H
X
L
L
H
L
X
X
H
L
H
X
L
H
X
X
H
X
V
X
X
H
X
H
X
H
X
X
H
X
V
X
H
X
X
H
X
V
X
Entry
H
L
L
H
L
X
X
X
Clock Suspend or
Active Power Down
X
X
Exit
Entry
H
H
L
Precharge Power Down Mode
Exit
L
H
H
H
X
X
V
X
H
DQM
X
X
6
7
7
L
H
L
H
X
H
X
H
X
L
No Operation Command
Deep Power Down Entry
Deep Power Down Exit
H
L
L
X
X
X
X
H
X
X
(V = Valid, X = Don’t Care, H = Logic High, L = Logic Low)
Note : 1. OP Code : Operand Code
A0~A10/AP,BA : Program keys. (@MRS)
2. MRS can be issued only at both banks precharge state.
A new command can be issued after 2 clock cycle of MRS.
3. Auto refresh functions as same as CBR refresh of DRAM.
The automatical precharge without Row precharge command is meant by “Auto”.
Auto/Self refresh can be issued only at both precharge state.
4. BA : Bank select address.
If “Low” at read, write, Row active and precharge, bank A is selected.
If “High” at read, write, Row active and precharge, bank B is selected.
If A10/AP is “High” at Row precharge, BA is ignored and both banks are selected.
5. During burst read or write with auto precharge, new read write command cannot be issued.
Another bank read write command can be issued at every burst length.
6. DQM sampled at positive going edge of a CLK masks the data-in at the very CLK (Write DQM latency is 0),
but makes the data-out Hi-Z state after 2 CLK cycles. (Read DQM latency is 2)
7. After Deep Power Down mode exit, a full new initialization of the memory device is mandatory.
PRELIMINARY (July, 2005, Version 0.1)
8
AMIC Technology, Corp.
A43E06161
Mode Register Filed Table to Program Modes
Register Programmed with MRS
Address
BA
A10/AP
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
Function
RFU
RFU
W.B.L
TM
CAS Latency
BT
Burst Length
(Note 1)
(Note 2)
Test Mode
Type
CAS Latency
A6 A5 A4 Latency
Burst Type
Burst Length
A8 A7
A3
Type
A2 A1 A0
BT=0
BT=1
Reserved
Reserved
4
0
0
1
1
0
1
0
1
Mode Register Set
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Reserved
-
0
1
Sequential
Interleave
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1
2
Vendor
Use
2
4
Only
3
8
8
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
256(Full)
Reserved
Reserved
Reserved
Reserved
Write Burst Length
Length
A9
0
Burst
1
Single Bit
(Note 3)
Power Up Sequence
1. Apply power and start clock, Attempt to maintain CKE = “H”, DQM = “H” and the other pins are NOP condition at inputs.
2. Maintain stable power, stable clock and NOP input condition for a minimum of 200µs.
3. Issue precharge commands for all banks of the devices.
4. Issue 2 or more auto-refresh commands.
5. Issue a mode register set command to initialize the mode register.
cf.) Sequence of 4 & 5 may be changed.
The device is now ready for normal operation.
Note : 1. RFU(Reserved for Future Use) should stay “0” during MRS cycle.
2. If A9 is high during MRS cycle, “Burst Read Single Bit Write” function will be enabled.
3. The full column burst (256bit) is available only at Sequential mode of burst type.
PRELIMINARY (July, 2005, Version 0.1)
9
AMIC Technology, Corp.
A43E06161
Burst Sequence (Burst Length = 4)
Initial address
Sequential
Interleave
A1
0
A0
0
0
1
2
3
1
2
3
0
2
3
0
1
3
0
1
2
0
1
2
3
1
0
3
2
2
3
2
1
0
0
1
3
0
1
1
0
1
1
Burst Sequence (Burst Length = 8)
Initial address
Sequential
Interleave
A2
A1
A0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
2
3
4
5
6
7
1
2
3
4
5
6
7
0
2
3
4
5
6
7
0
1
3
4
5
6
7
0
1
2
4
5
6
7
0
1
2
3
5
6
7
0
1
2
3
4
5
7
0
1
2
3
4
5
6
7
1
2
3
0
1
6
7
4
5
3
2
1
0
7
6
5
4
4
5
6
7
0
1
2
3
5
4
7
6
1
0
3
2
6
7
4
5
2
3
0
1
7
6
5
4
3
2
1
0
6
7
0
1
2
3
4
0
1
2
3
4
5
6
0
3
2
5
4
7
6
PRELIMINARY (July, 2005, Version 0.1)
10
AMIC Technology, Corp.
A43E06161
1. Power must be applied to either CKE and DQM inputs to
pull them high and other pins are NOP condition at the
inputs before or along with VDD (and VDDQ) supply.
The clock signal must also be asserted at the same time.
2. After VDD reaches the desired voltage, a minimum pause
of 200 microseconds is required with inputs in NOP
condition.
3. Both banks must be precharged now.
4. Perform a minimum of 2 Auto refresh cycles to stabilize the
internal circuitry.
Device Operations
Clock (CLK)
The clock input is used as the reference for all SDRAM
operations. All operations are synchronized to the positive
going edge of the clock. The clock transitions must be
monotonic between VIL and VIH. During operation with CKE
high all inputs are assumed to be in valid state (low or high)
for the duration of set up and hold time around positive edge
of the clock for proper functionality and ICC specifications.
5. Perform a MODE REGISTER SET cycle to program the
CAS latency, burst length and burst type as the default
value of mode register is undefined.
Clock Enable (CLK)
The clock enable (CKE) gates the clock onto SDRAM. If CKE
goes low synchronously with clock (set-up and hold time
same as other inputs), the internal clock is suspended form
the next clock cycle and the state of output and burst address
is frozen as long as the CKE remains low. All other inputs are
ignored from the next clock cycle after CKE goes low. When
both banks are in the idle state and CKE goes low
synchronously with clock, the SDRAM enters the power down
mode form the next clock cycle. The SDRAM remains in the
power down mode ignoring the other inputs as long as CKE
remains low. The power down exit is synchronous as the
internal clock is suspended. When CKE goes high at least
“tSS + 1 CLOCK” before the high going edge of the clock, then
the SDRAM becomes active from the same clock edge
accepting all the input commands.
At the end of one clock cycle from the mode register set
cycle, the device is ready for operation.
When the above sequence is used for Power-up, all the
out-puts will be in high impedance state. The high
impedance of outputs is not guaranteed in any other
power-up sequence.
cf.) Sequence of 4 & 5 may be changed.
Mode Register Set (MRS)
The mode register stores the data for controlling the various
operation modes of SDRAM. It programs the CAS latency,
addressing mode, burst length, test mode and various vendor
specific options to make SDRAM useful for variety of different
applications. The default value of the mode register is not
defined, therefore the mode register must be written after
power up to operate the SDRAM. The mode register is
Bank Select (BA)
written by asserting low on
SDRAM should be in active mode with CKE already high
prior to writing the mode register). The state of address pins
,
,
,
(The
WE
CS RAS CAS
This SDRAM is organized as two independent banks of
524,288 words X 16 bits memory arrays. The BA inputs is
latched at the time of assertion of
and
to select
CAS
RAS
A0~A10/AP
and
BA
in
the
same
cycle
as
the bank to be used for the operation. When BA is asserted
low, bank A is selected. When BA is asserted high, bank B is
selected. The bank select BA is latched at bank activate,
read, write mode register set and precharge operations.
,
,
,
going low is the data written in the
WE
CS RAS CAS
mode register. One clock cycle is required to complete the
write in the mode register. The mode register contents can
be changed using the same command and clock cycle
requirements during operation as long as both banks are in
the idle state. The mode register is divided into various fields
depending on functionality. The burst length field uses
A0~A2, burst type uses A3, addressing mode uses A4~A6,
A7~A8, A10/AP and BA are used for vendor specific options
or test mode. And the write burst length is programmed using
A9. A7~A8, A10/AP and BA must be set to low for normal
SDRAM operation.
Address Input (A0 ~ A10/AP)
The 19 address bits required to decode the 524,288 word
locations are multiplexed into 11 address input pins
(A0~A10/AP). The 11 bit row address is latched along with
and BA during bank activate command. The 8 bit
RAS
column address is latched along with
,
and BA
WE
CAS
during read or write command.
Refer to table for specific codes for various burst length,
addressing modes and CAS latencies.
NOP and Device Deselect
Bank Activate
When
,
and
are high, the SDRAM performs
WE
RAS CAS
The bank activate command is used to select a random row
no operation (NOP). NOP does not initiate any new
operation, but is needed to complete operations which
require more than single clock like bank activate, burst read,
auto refresh, etc. The device deselect is also a NOP and is
in an idle bank. By asserting low on
and
with
CS
RAS
desired row and bank addresses, a row access is initiated.
The read or write operation can occur after a time delay of
tRCD(min) from the time of bank activation. tRCD(min) is an
internal timing parameter of SDRAM, therefore it is
dependent on operating clock frequency. The minimum
number of clock cycles required between bank activate and
read or write command should be calculated by dividing
tRCD(min) with cycle time of the clock and then rounding off
the result to the next higher integer. The SDRAM has two
internal banks on the same chip and shares part of the
internal circuitry to reduce chip area, therefore it restricts the
entered by asserting
high.
high disables the
CS
CS
command decoder so that
address inputs are ignored.
,
and , and all the
WE
RAS CAS
Power-Up
The following sequence is recommended for POWER UP
PRELIMINARY (July, 2005, Version 0.1)
11
AMIC Technology, Corp.
A43E06161
activation of both banks immediately. Also the noise
generated during sensing of each bank of SDRAM is high
requiring some time for power supplies recover before the
other bank can be sensed reliably. tRRD(min) specifies the
minimum time required between activating different banks.
The number of clock cycles required between different bank
activation must be calculated similar to tRCD specification. The
minimum time required for the bank to be active to initiate
sensing and restoring the complete row of dynamic cells is
determined by tRAS(min) specification before a precharge
command to that active bank can be asserted. The maximum
time any bank can be in the active state is determined by
tRAS(max). The number of cycles for both tRAS(min) and
tRAS(max) can be calculated similar to tRCD specification.
DQM and zero cycle for write, which means DQM masking
occurs two cycles later in the read cycle and occurs in the
same cycle during write cycle. DQM operation is
synchronous with the clock, therefore the masking occurs for
a complete cycle. The DQM signal is important during burst
interrupts of write with read or precharge in the SDRAM. Due
to asynchronous nature of the internal write, the DQM
operation is critical to avoid unwanted or incomplete writes
when the complete burst write is not required.
Precharge
The precharge operation is performed on an active bank by
asserting low on
,
,
and A10/AP with valid BA
WE
CS RAS
of the bank to be precharged. The precharge command can
be asserted anytime after tRAS(min) is satisfied from the bank
activate command in the desired bank. “tRP” is defined as the
minimum time required to precharge a bank.
Burst Read
The burst read command is used to access burst of data on
consecutive clock cycles from an active row in an active
bank. The burst read command is issued by asserting low on
The minimum number of clock cycles required to complete
row precharge is calculated by dividing “tRP” with clock cycle
time and rounding up to the next higher integer. Care should
be taken to make sure that burst write is completed or DQM
is used to inhibit writing before precharge command is
asserted. The maximum time any bank can be active is
specified by tRAS(max). Therefore, each bank has to be
precharged within tRAS(max) from the bank activate
command. At the end of precharge, the bank enters the idle
state and is ready to be activated again.
and
with
being high on the positive edge of
WE
CS
CAS
the clock. The bank must be active for at least tRCD(min)
before the burst read command is issued. The first output
appears CAS latency number of clock cycles after the issue
of burst read command. The burst length, burst sequence
and latency from the burst read command is determined by
the mode register which is already programmed. The burst
read can be initiated on any column address of the active
row. The address wraps around if the initial address does not
start from a boundary such that number of outputs from each
I/O are equal to the burst length programmed in the mode
register. The output goes into high-impedance at the end of
the burst, unless a new burst read was initiated to keep the
data output gapless. The burst read can be terminated by
issuing another burst read or burst write in the same bank or
the other active bank or a precharge command to the same
bank. The burst stop command is valid at every page burst
length.
Entry to Power Down, Auto refresh, Self refresh and Mode
register Set etc, is possible only when both banks are in idle
state.
Auto Precharge
The precharge operation can also be performed by using
auto precharge. The SDRAM internally generates the timing
to satisfy tRAS(min) and “tRP” for the programmed burst length
and CAS latency. The auto precharge command is issued at
the same time as burst read or burst write by asserting high
on A10/AP. If burst read or burst write command is issued
with low on A10/AP, the bank is left active until a new
command is asserted. Once auto precharge command is
given, no new commands are possible to that particular bank
until the bank achieves idle state.
Burst Write
The burst write command is similar to burst read command,
and is used to write data into the SDRAM consecutive clock
cycles in adjacent addresses depending on burst length and
burst sequence. By asserting low on
,
and
with
WE
CS CAS
Both Banks Precharge
valid column address, a write burst is initiated. The data
inputs are provided for the initial address in the same clock
cycle as the burst write command. The input buffer is
deselected at the end of the burst length, even though the
internal writing may not have been completed yet. The writing
can not complete to burst length. The burst write can be
terminated by issuing a burst read and DQM for blocking
data inputs or burst write in the same or the other active
bank. The burst stop command is valid only at full page burst
length where the writing continues at the end of burst and the
burst is wrap around. The write burst can also be terminated
by using DQM for blocking data and precharging the bank
“tRDL” after the last data input to be written into the active row.
See DQM OPERATION also.
Both banks can be precharged at the same time by using
Precharge all command. Asserting low on
,
and
CS RAS
with high on A10/AP after both banks have satisfied
WE
tRAS(min) requirement, performs precharge on both banks. At
the end of tRP after performing precharge all, both banks are
in idle state.
Auto Refresh
The storage cells of SDRAM need to be refreshed every
32ms to maintain data. An auto refresh cycle accomplishes
refresh of a single row of storage cells. The internal counter
increments automatically on every auto refresh cycle to
refresh all the rows. An auto refresh command is issued by
DQM Operation
asserting low on
,
and
with high on CKE and
CAS
CS RAS
The DQM is used to mask input and output operation. It
. The auto refresh command can only be asserted with
WE
both banks being in idle state and the device is not in power
down mode (CKE is high in the previous cycle). The time
required to complete the auto refresh operation is specified
works similar to
during read operation and inhibits writing
OE
during write operation. The read latency is two cycles from
PRELIMINARY (July, 2005, Version 0.1)
12
AMIC Technology, Corp.
A43E06161
by “tRC(min)”. The minimum number of clock cycles required
can be calculated by driving “tRC” with clock cycle time and
then rounding up to the next higher integer. The auto refresh
command must be followed by NOP’s until the auto refresh
operation is completed. Both banks will be in the idle state at
the end of auto refresh operation. The auto refresh is the
preferred refresh mode when the SDRAM is being used for
normal data transactions. The auto refresh cycle can be
performed once in 15.6us or a burst of 2048 auto refresh
cycles once in 32ms.
. Once the self refresh mode is entered, only CKE state
being low matters, all the other inputs including clock are
ignored to remain in the self refresh.
The self refresh is exited by restarting the external clock and
then asserting high on CKE. This must be followed by NOP’s
for a minimum time of “tRC” before the SDRAM reaches idle
state to begin normal operation. If the system uses burst auto
refresh during normal operation, it is recommended to used
burst 2048 auto refresh cycles immediately after exiting self
refresh.
WE
Self Refresh
Deep Power Down Mode
The self refresh is another refresh mode available in the
SDRAM. The self refresh is the preferred refresh mode for
data retention and low power operation of SDRAM. In self
refresh mode, the SDRAM disables the internal clock and all
the input buffers except CKE. The refresh addressing and
timing is internally generated to reduce power consumption.
The self refresh mode is entered from all banks idle state by
The Deep Power Down Mode is an unique function on Low
Power SDRAMs with very low standby currents. All internal
voltage generators inside the Low Power SDRAMs are
stopped and all memory data will be lost in this mode. To
enter the Deep Power Down Mode all banks must be
precharged and the necessary Precharged Delay tRP must
occur.
asserting low on
,
,
and CKE with high on
CS RAS CAS
PRELIMINARY (July, 2005, Version 0.1)
13
AMIC Technology, Corp.
A43E06161
Basic feature And Function Descriptions
1. CLOCK Suspend
1) Click Suspended During Write (BL=4)
2) Clock Suspended During Read (BL=4)
CLK
CMD
CKE
WR
RD
Masked by CKE
Masked by CKE
Internal
CLK
DQ(CL2)
DQ(CL3)
D0
D0
D1
D1
D2
D2
D3
D3
Q0
Q1
Q0
Q2
Q1
Q3
Q2
Q3
Not Written
Suspended Dout
Note: CLK to CLK disable/enable=1 clock
2. DQM Operation
2) Read Mask (BL=4)
1) Write Mask (BL=4)
CLK
CMD
WR
RD
DQM
Masked by CKE
D3
Masked by CKE
Q1
Hi-Z
Hi-Z
DQ(CL2)
DQ(CL3)
D0
D0
D1
D1
Q0
Q3
Q2
D3
Q1
Q3
DQM to Data-in Mask = 0CLK
DQM to Data-out Mask = 2
2) Read Mask (BL=4)
CLK
CMD
CKE
RD
DQM
Hi-Z
Hi-Z
Hi-Z
Hi-Z
Q0
Q2
Q1
Q4
Q3
Q6
Q5
Q7
Q6
Q8
Q7
DQ(CL2)
DQ(CL3)
Hi-Z
Hi-Z
* Note : 1. DQM makes data out Hi-Z after 2 clocks which should masked by CKE “L”.
2. DQM masks both data-in and data-out.
PRELIMINARY (July, 2005, Version 0.1)
14
AMIC Technology, Corp.
A43E06161
3. CAS Interrupt (I)
1) Read interrupted by Read (BL=4)Note 1
CLK
CMD
RD
A
RD
B
ADD
DQ(CL2)
DQ(CL3)
QA0 QB0 QB1 QB2 QB3
QA0 QB0 QB1 QB2 QB3
t
CCD
Note2
2) Write interrupted by Write (BL =2)
3) Write interrupted by Read (BL =2)
CLK
WR WR
WR
RD
CMD
t
CCD
tCCD
Note2
Note2
ADD
DQ
A
B
A
B
DA0 DB0 DB1
DQ(CL2)
DQ(CL3)
DA0
QB0 QB1
t
CDL
Note3
DA0
QB0 QB1
t
CDL
Note3
Note : 1. By “Interrupt”, It is possible to stop burst read/write by external command before the end of burst.
By “ Interrupt”, to stop burst read/write by access; read, write and block write.
CAS
2. tCCD :
CAS
to
delay. (=1CLK)
CAS
CAS
3. tCDL : Last data in to new column address delay. (= 1CLK).
PRELIMINARY (July, 2005, Version 0.1)
15
AMIC Technology, Corp.
A43E06161
4. CAS Interrupt (II) : Read Interrupted Write & DQM
(1) CL=2, BL=4
CLK
i) CMD
RD
RD
WR
D0
DQM
DQ
ii) CMD
D1
D2
D3
D2
WR
DQM
DQ
Hi-Z
D0
D1
D3
D2
D1
RD
RD
WR
iii) CMD
DQM
DQ
Hi-Z
D0
D1
D3
D2
iv) CMD
WR
DQM
DQ
Hi-Z
Note 1
Q0
D0
D3
(2) CL=3, BL=4
CLK
i) CMD
DQM
RD
RD
RD
RD
WR
D0
DQ
D1
D2
D3
D2
ii) CMD
WR
DQM
DQ
D0
D1
D3
D2
iii) CMD
WR
DQM
DQ
D0
D1
D3
D2
D1
iv) CMD
WR
DQM
DQ
Hi-Z
D0
D1
D3
D2
v) CMD
RD
WR
DQM
DQ
Hi-Z
Q0
D0
D3
Note 2
* Note : 1. To prevent bus contention, there should be at least one gap between data in and data out.
2. To prevent bus contention, DQM should be issued which makes a least one gap between data in and data out.
PRELIMINARY (July, 2005, Version 0.1)
16
AMIC Technology, Corp.
A43E06161
5. Write Interrupted by Precharge & DQM
CLK
Note 2
Note 1
CMD
WR
D0
PRE
D3
DQM
DQ
D1
D2
Masked by DQM
Note : 1. To inhibit invalid write, DQM should be issued.
2. This precharge command and burst write command should be of the same bank, otherwise it is not precharge
interrupt but only another bank precharge of dual banks operation.
6. Precharge
1) Normal Write (BL=4)
CLK
CMD
DQ
WR
D0
PRE
D1
D2
D3
t
RDL
2) Read (BL=4)
CLK
CMD
RD
PRE
Q2
DQ(CL2)
Q0
Q1
Q0
Q3
Q2
DQ(CL3)
Q1
Q3
7. Auto Precharge
1) Normal Write (BL=4)
CLK
CMD
DQ
WR
D0
D1
D2
D3
Note 1
Auto Precharge Starts
2) Read (BL=4)
CLK
CMD
DQ(CL2)
DQ(CL3)
RD
Q0
Q1
Q0
Q2
Q1
Q3
Q2
Q3
Note 1
Auto Precharge Starts
* Note : 1. The row active command of the precharge bank can be issued after tRP from this point.
The new read/write command of other active bank can be issued from this point.
At burst read/write with auto precharge,
interrupt of the same/another bank is illegal.
CAS
PRELIMINARY (July, 2005, Version 0.1)
17
AMIC Technology, Corp.
A43E06161
8. Burst Stop & Precharge Interrupt
1) Write Interrupted by Precharge (BL=4)
CLK
2) Write Burst Stop (BL=8)
CLK
CMD
CMD
WR
PRE
WR
STOP
DQM
DQ
D0
D1
D2
D3
DQ
D1
D0
D2
Note 1
t
RDL
t
BDL (note 2)
3) Read Interrupted by Precharge (BL=4)
CLK
4) Read Burst Stop (BL=4)
CLK
CMD
CMD
DQ(CL2)
DQ(CL3)
RD
RD
PRE
Q0
STOP
Q0
Note 3
1
Note 3
1
DQ(CL2)
DQ(CL3)
Q1
Q0
Q1
Q0
2
2
Q1
Q1
9. MRS
Mode Register Set
CLK
Note 4
PRE
MRS ACT
1CLK
CMD
t
RP
Note : 1. tRDL : 2CLK, Last Data in to Row Precharge.
2. tBDL : 1CLK, Last Data in to Burst Stop Delay.
3. Number of valid output data after Row precharge or burst stop : 1,2 for CAS latency=2,3 respectively.
4. PRE : Both banks precharge if necessary.
MRS can be issued only at all bank precharge state.
PRELIMINARY (July, 2005, Version 0.1)
18
AMIC Technology, Corp.
A43E06161
10. Clock Suspend Exit & Power Down Exit
1) Clock Suspend (=Active Power Down) Exit
CLK
2) Power Down (=Precharge Power Down) Exit
CLK
CKE
CKE
t
SS
t
SS
Note 2
Note 1
Internal
CLK
Internal
CLK
NOP
ACT
RD
CMD
CMD
11. Auto Refresh & Self Refresh
Note 3
1) Auto Refresh
CLK
Note 4
Note 5
CKE
PRE
Internal
CLK
AR
CMD
CMD
t
RP
tRC
Note 6
2) Self Refresh
CLK
Note 4
CMD
CKE
PRE
SR
CMD
t
RP
tRC
* Note : 1. Active power down : one or more bank active state.
2. Precharge power down : both bank precharge state.
3. The auto refresh is the same as CBR refresh of conventional DRAM.
No precharge commands are required after Auto Refresh command.
During tRC from auto refresh command, any other command can not be accepted.
4. Before executing auto/self refresh command, both banks must be idle state.
5. MRS, Bank Active, Auto/Self Refresh, Power Down Mode Entry.
6. During self refresh mode, refresh interval and refresh operation are performed internally.
After self refresh entry, self refresh mode is kept while CKE is LOW.
During self refresh mode, all inputs expect CKE will be don’t cared, and outputs will be in Hi-Z state.
During tRC from self refresh exit command, any other command can not be accepted.
Before/After self refresh mode, burst auto refresh cycle (2K cycles ) is recommended.
PRELIMINARY (July, 2005, Version 0.1)
19
AMIC Technology, Corp.
A43E06161
12. About Burst Type Control
At MRS A3=”0”. See the BURST SEQUENCE TABE.(BL=4,8)
BL=1,2,4,8 and full page wrap around.
At MRS A3=” 1”. See the BURST SEQUENCE TABE.(BL=4,8)
BL=4,8 At BL=1,2 Interleave Counting = Sequential Counting
Sequential counting
Basic
MODE
Interleave counting
Every cycle Read/Write Command with random column address can realize
Random Column Access.
That is similar to Extended Data Out (EDO) Operation of convention DRAM.
Random
MODE
Random column Access
tCCD = 1 CLK
13. About Burst Length Control
At MRS A2,1,0 = “000”.
At auto precharge, tRAS should not be violated.
1
Basic
MODE
At MRS A2,1,0 = “001”.
At auto precharge, tRAS should not be violated.
At MRS A2,1,0 = “010”
2
4
8
At MRS A2,1,0 = “011”.
At MRS A9=”1”.
Read burst = 1,2,4,8, full page/write Burst =1
At auto precharge of write, tRAS should not be violated.
Before the end of burst, Row precharge command of the same bank
Stops read/write burst with Row precharge.
Special
BRSW
MODE
Interrupt
RAS
(Interrupted by Precharge)
tRDL= 2 with DQM, valid DQ after burst stop is 1,2 for CL=2,3 respectively
Interrupt
MODE
During read/write burst with auto precharge,
Before the end of burst, new read/write stops read/write burst and starts new
read/write burst or block write.
interrupt cannot be issued.
RAS
Interrupt
CAS
During read/write burst with auto precharge,
interrupt can not be issued.
CAS
PRELIMINARY (July, 2005, Version 0.1)
20
AMIC Technology, Corp.
A43E06161
Power On Sequence & Auto Refresh
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
CS
High level is necessary
tRP
tRC
RAS
CAS
ADDR
BA
KEY
Ra
KEY
KEY
BS
Ra
A10/AP
WE
DQM
DQ
High level is necessary
High-Z
Precharge
(All Banks)
Auto Refresh
Auto Refresh
Mode Regiser Set
Row Active
(A-Bank)
: Don't care
PRELIMINARY (July, 2005, Version 0.1)
21
AMIC Technology, Corp.
A43E06161
Single Bit Read-Write-Read Cycles (Same Page) @CAS Latency=3, Burst Length=1
tCH
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
tCL
tCC
High
tRAS
tRC
tSH
*Note 1
CS
tSS
tRCD
tRP
tSH
RAS
tSS
tCCD
tSH
CAS
ADDR
BA
tSS
tSH
tSS
Ra
Ca
Cb
Cc
Rb
tSS
tSH
*Note 2,3
*Note 2,3
*Note 2,3 *Note 4
*Note 2
*Note 2
BS
BS
BS
BS
BS
BS
*Note 3
*Note 3
*Note 3 *Note 4
A10/AP
Ra
Rb
tSH
WE
tSS
tSS
tSH
tSH
DQM
DQ
tRAC
tSAC
tSLZ
Qa
Db
Qc
tSS
tOH
tSHZ
Read
Write
Row Active
Read
Row Active
Precharge
: Don't care
PRELIMINARY (July, 2005, Version 0.1)
22
AMIC Technology, Corp.
A43E06161
* Note : 1. All inputs can be don’t care when
is high at the CLK high going edge.
CS
2. Bank active & read/write are controlled by BA.
BA
0
Active & Read/Write
Bank A
1
Bank B
3. Enable and disable auto precharge function are controlled by A10/AP in read/write command.
A10/AP
BA
0
Operation
Disable auto precharge, leave bank A active at end of burst.
Disable auto precharge, leave bank B active at end of burst.
Enable auto precharge, precharge bank A at end of burst.
Enable auto precharge, precharge bank B at end of burst.
0
1
0
1
1
4. A10/AP and BA control bank precharge when precharge command is asserted.
A10/AP
BA
0
Precharge
Bank A
0
0
1
1
Bank B
X
Both Bank
PRELIMINARY (July, 2005, Version 0.1)
23
AMIC Technology, Corp.
A43E06161
Read & Write Cycle at Same Bank @Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
*Note 1
RC
t
CS
tRCD
RAS
CAS
*Note 2
ADDR
BA
Ra
Ca0
Rb
Cb0
A10/AP
Ra
Rb
WE
DQM
tOH
DQ
(CL = 2)
Qa0
Qa1
Qa2
Qa3
Qa2
Db0
Db0
Db1
Db2
Db3
t
RAC
*Note 4
t
RDL
t
SAC
tSHZ
*Note 3
t
OH
DQ
(CL = 3)
Qa0
Qa1
Qa3
Db1
Db2
Db3
t
RAC
*Note 4
t
RDL
t
SHZ
t
SAC
*Note 3
Row Active
(A-Bank)
Precharge
(A-Bank)
Row Active
(A-Bank)
Write
(A-Bank)
Read
(A-Bank)
Precharge
(A-Bank)
: Don't care
*Note : 1. Minimum row cycle times is required to complete internal DRAM operation.
2. Row precharge can interrupt burst on any cycle. [CAS latency-1] valid output data available after Row
enters precharge. Last valid output will be Hi-Z after tSHZ from the clock.
3. Access time from Row address. tCC*(tRCD + CAS latency-1) + tSAC
4. Output will be Hi-Z after the end of burst. (1,2,4 & 8)
At Full page bit burst, burst is wrap-around.
PRELIMINARY (July, 2005, Version 0.1)
24
AMIC Technology, Corp.
A43E06161
Page Read & Write Cycle at Same Bank @Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
t
RCD
RAS
CAS
*Note 2
ADDR
BA
Ra
Ca0
Cb0
Cc0
Cd0
A10/AP
Ra
t
RDL
t
CDL
WE
*Note 2
*Note1
*Note3
DQM
DQ
(CL=2)
Qa0
Qa1
Qb0
Qa1
Qb1
Qb0
Dc0
Dc1
Dc1
Dd0
Dd0
Dd1
Dd1
DQ
(CL=3)
Qa0
Dc0
Row Active
(A-Bank)
Write
(A-Bank)
Write
(A-Bank)
Read
(A-Bank)
Read
(A-Bank)
Precharge
(A-Bank)
: Don't care
*Note : 1. To write data before burst read ends, DQM should be asserted three cycle prior to write command to avoid bus contention.
2. Row precharge will interrupt writing. Last data input, tRDL before Row precharge, will be written.
3. DQM should mask invalid input data on precharge command cycle when asserting precharge before end of burst. Input data
after Row precharge cycle will be masked internally.
PRELIMINARY (July, 2005, Version 0.1)
25
AMIC Technology, Corp.
A43E06161
Page Read Cycle at Different Bank @Burst Length = 4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
*Note 1
CS
RAS
CAS
*Note 2
RAa
RAa
CAa
RBb
RBb
CBb
CAc
CBd
CAe
ADDR
BA
A10/AP
WE
DQM
DQ
(CL=2)
QAa0 QAa1 QAa2 QAa3 QBb0 QBb1 QBb2 QBb3 QAc0 QAc1 QBd0 QBd1 QAe0 QAe1
QAa0 QAa1 QAa2 QAa3 QBb0 QBb1 QBb2 QBb3 QAc0 QAc1 QBd0 QBd1 QAe0 QAe1
DQ
(CL=3)
Read
(A-Bank)
Read
(B-Bank)
Read
(A-Bank)
Precharge
(A-Bank)
Row Active
(B-Bank)
Read
(B-Bank)
Row Active
(A-Bank)
Read
(A-Bank)
: Don't care
* Note : 1.
can be don’t care when
, and
RAS CAS
are high at the clock high going edge.
WE
CS
2. To interrupt a burst read by row precharge, both the read ad the precharge banks must be the same.
PRELIMINARY (July, 2005, Version 0.1)
26
AMIC Technology, Corp.
A43E06161
Page Write Cycle at Different Bank @Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
*Note 2
RAa
RAa
CAa
RBb
RBb
CBb
CAc
CBd
ADDR
BA
A10/AP
DQ
DAa0 DAa1 DAa2 DAa3 DBb0 DBb1 DBb2 DBb3 DAc0 DAc1 DBd0 DBd1
tRDL
t
CDL
WE
*Note 1
DQM
Row Active
(B-Bank)
Write
(B-Bank)
Precharge
(Both Banks)
Write
(A-Bank)
Row Active with
(A-Bank)
Write
(A-Bank)
Write
(B-Bank)
: Don't care
* Note:
1. To interrupt burst write by Row precharge, DQM should be asserted to mask invalid input data.
2. To interrupt burst write by Row precharge, both the write and precharge banks must be the same.
PRELIMINARY (July, 2005, Version 0.1)
27
AMIC Technology, Corp.
A43E06161
Read & Write Cycle at Different Bank @Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
RAa
CAa
RBb
CBb
RAc
CAc
ADDR
BA
A10/AP
RAa
RBb
RAc
tCDL
*Note 1
WE
DQM
DQ
(CL=2)
QAa0 QAa1 QAa2 QAa3
DBb0 DBb1 DBb2 DBb3
DBb0 DBb1 DBb2 DBb3
QAc0 QAc1 QAc2
QAc0 QAc1
DQ
(CL=3)
QAa0 QAa1 QAa2 QAa3
Row Active
(A-Bank)
Read
(A-Bank)
Precharge
(A-Bank)
Write
(B-Bank)
Read
(A-Bank)
Row Active
(B-Bank)
Row Active
(A-Bank)
: Don't care
* Note : tCDL should be met to complete write.
PRELIMINARY (July, 2005, Version 0.1)
28
AMIC Technology, Corp.
A43E06161
Read & Write Cycle with Auto Precharge I @Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
RAa
RAa
RBb
RBb
CAa
CBb
ADDR
BA
A10/AP
WE
DQM
DQ
(CL=2)
QAa0 QAa1 QAa2 QAa3
DBb0 DBb1 DBb2 DBb3
DBb0 DBb1 DBb2 DBb3
DQ
(CL=3)
QAa0 QAa1 QAa2 QAa3
Row Active
(A-Bank)
Auto Precharge
Start Point
Read with
Auto Precharge
(A-Bank)
Auto Precharge
Start Point
(A-Bank)
Write with
Auto Precharge
(B-Bank)
(B-Bank)
Row Active
(B-Bank)
: Don't care
*Note : tRCD should be controlled to meet minimum tRAS before internal precharge start.
(In the case of Burst Length=1 & 2, BRSW mode)
PRELIMINARY (July, 2005, Version 0.1)
29
AMIC Technology, Corp.
A43E06161
Read & Write Cycle with Auto Precharge II @Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
Ra
Rb
Ca
Cb
Ra
Ca
ADDR
BA
Ra
Rb
Ra
A10/AP
WE
DQM
Qa0
Qa1
Qa0
Qb0 Qb1
Qa1 Qb0
Qb2
Qb3
Da0
Da0
Da1
Da1
DQ
(CL=2)
Qb1
Qb2
Qb3
DQ
(CL=3)
Read without
Auto Precharge
(B-Bank)
Auto Precharge
Strart Point
Row Active
(A-Bank)
Read with
Auto Pre
Charge
Precharge
(B-Bank)
Row Active
(A-Bank)
Write with
Auto Precharge
(A-Bank)
(A-Bank)
(A-Bank) *Note 1
Row Active
(B-Bank)
: Don't care
* Note : When Read(Write) command with auto precharge is issued at A-Bank after A and B Bank activation.
- if read(Write) command without auto precharge is issued at B-Bank before A Bank auto precharge starts, A Bank auto
precharge will start at B Bank read command input point.
- Any command can not be issued at A Bank during tRP after A Bank auto precharge starts.
PRELIMINARY (July, 2005, Version 0.1)
30
AMIC Technology, Corp.
A43E06161
Read & Write Cycle with Auto Precharge III @Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
Ra
Ca
Rb
Cb
ADDR
BA
A10/AP
Ra
Rb
WE
DQM
DQ
(CL=2)
Qa0
Qa1
Qa2 Qa3
Qa1 Qa2
Qb0
Qb1
Qb2
Qb3
DQ
(CL=3)
Qa0
Qa3
Qb0
Qb1
Db2
Db3
* Note 1
Row Active
(A-Bank)
Read with
Auto Preharge
(A-Bank)
Read with
Auto Precharge
(B-Bank)
Auto Precharge
Start Point
Auto Precharge
Start Point
(A-Bank)
(B-Bank)
Row Active
(B-Bank)
: Don't care
* Note : Any command to A-bank is not allowed in this period.
tRP is determined from at auto precharge start point
PRELIMINARY (July, 2005, Version 0.1)
31
AMIC Technology, Corp.
A43E06161
Read Interrupted by Precharge Command & Read Burst Stop Cycle (@Burst Length = Full Page)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
ADDR
BA
RAa
RAa
CAa
CAb
* Note 1
* Note 1
A10/AP
WE
DQM
* Note 2
1
1
DQ
(CL=2)
QAa1 QAa2 QAa3 QAa4
QAb0 QAb1 QAb2 QAb3 QAb4 QAb5
QAa0
2
2
DQ
(CL=3)
QAa0 QAa1 QAa2 QAa3 QAa4
QAb0 QAb1 QAb2 QAb3 QAb4 QAb5
Read
(A-Bank)
Read
(A-Bank)
Precharge
(A-Bank)
Row Active
(A-Bank)
Burst Stop
: Don't care
* Note : 1. At full page mode, burst is wrap-around at the end of burst. So auto precharge is impossible.
2. About the valid DQ’s after burst stop, it is same as the case of
interrupt.
RAS
Both cases are illustrated above timing diagram. See the label 1,2 on them.
But at burst write, burst stop and interrupt should be compared carefully.
RAS
Refer the timing diagram of “Full page write burst stop cycle”.
3. Burst stop is valid at every burst length.
PRELIMINARY (July, 2005, Version 0.1)
32
AMIC Technology, Corp.
A43E06161
Write Interrupted by Precharge Command & Write Burst Stop Cycle (@ Burst Length = Full Page)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
ADDR
BA
RAa
RAa
CAa
CAb
* Note 1
* Note 1
A10/AP
t
RDL
t
BDL
WE
* Note 3
DQM
DQ
* Note 2
DAa0 DAa1 DAa2 DAa3 DAa4
DAb0 DAb1 DAb2 DAb3 DAb4 DAb5
Write
(A-Bank)
Write
(A-Bank)
Precharge
(A-Bank)
Row Active
(A-Bank)
Burst Stop
: Don't care
* Note : 1. At full page mode, burst is wrap-around at the end of burst. So auto precharge is impossible.
2. Data-in at the cycle of burst stop command cannot be written into corresponding memory cell.
It is defined by AC parameter of tBDL(=1CLK).
3. Data-in at the cycle of interrupted by precharge cannot be written into the corresponding memory cell.
It is defined by AC parameter of tRDL(=2CLK).
DQM at write interrupted by precharge command is needed to ensure tRDL of 2CLK.
DQM should mask invalid input data on precharge command cycle when asserting precharge before end of burst.
Input data after Row precharge cycle will be masked internally.
4. Burst stop is valid only at every burst length.
PRELIMINARY (July, 2005, Version 0.1)
33
AMIC Technology, Corp.
A43E06161
Burst Read Single Bit Write Cycle @Burst Length=2, BRSW
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
High
CS
RAS
CAS
* Note 2
RAa
RAa
CAa
CBc
CAd
RBb
RBb
CAb
RAc
ADDR
BA
A10/AP
RAc
WE
DQM
DQ
(CL=2)
QAb0 QAb1
DBc0
DBc0
QAd0 QAd1
DAa0
DAa0
DQ
(CL=3)
QAb0 QAb1
QAd0 QAd1
Row Active
(A-Bank)
Read
(A-Bank)
Precharge
(A-Bank)
Row Active
(A-Bank)
Row Active
(B-Bank)
Write with
Auto Precharge
(B-Bank)
Read with
Auto Precharge
(A-Bank)
Write
(A-Bank)
: Don't care
* Note : 1. BRSW mode is enabled by setting A9 “High” at MRS (Mode Register Set).
At the BRSW Mode, the burst length at write is fixed to “1” regardless of programed burst length.
2. When BRSW write command with auto precharge is executed, keep it in mind that tRAS should not be violated.
Auto precharge is executed at the burst-end cycle, so in the case of BRSW write command,
The next cycle starts the precharge.
PRELIMINARY (July, 2005, Version 0.1)
34
AMIC Technology, Corp.
A43E06161
Clock Suspension & DQM Operation Cycle @CAS Latency = 2, Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
CS
RAS
CAS
Ra
Ca
Cb
Cc
ADDR
BA
A10/AP
Ra
WE
* Note 1
DQM
DQ
Qa0
Qa1
Qb0
Qb1
Dc0
Dc2
Qa2
Qa3
t
SHZ
tSHZ
Clock
Suspension
Write
DQM
Row Active
Read
Read
Read DQM
Clock
Suspension
Write
: Don't care
* Note : DQM needed to prevent bus contention.
PRELIMINARY (July, 2005, Version 0.1)
35
AMIC Technology, Corp.
A43E06161
Active/Precharge Power Down Mode @CAS Lantency=2, Burst Length=4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
* Note 2
SS
t
SS
t
t
SS
tSS
* Note 1
*Note 3
CS
RAS
CAS
Ra
Ca
ADDR
BA
Ra
A10/AP
WE
DQM
DQ
Qa0
Qa1
Qa2
Precharge
Power-down
Exit
Precharge
Power-down
Entry
Read
Precharge
Row Active
Active
Power-down
Exit
Active
Power-down
Entry
: Don't care
* Note : 1. All banks should be in idle state prior to entering precharge power down mode.
2. CKE should be set high at least “1CLK + tSS” prior to Row active command.
3. Cannot violate minimum refresh specification. (32ms)
PRELIMINARY (July, 2005, Version 0.1)
36
AMIC Technology, Corp.
A43E06161
Self Refresh Entry & Exit Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
CKE
* Note 4
* Note 2
t
RC min.
t
SS
* Note 6
* Note 1
* Note 3
t
SS
* Note 5
CS
RAS
CAS
* Note 7
* Note 7
ADDR
BA
A10/AP
WE
DQM
DQ
Hi-Z
Hi-Z
Self Refresh Exit
Auto Refresh
Self Refresh Entry
: Don't care
* Note : TO ENTER SELF REFRESH MODE
1. with CKE should be low at the same clock cycle.
CS RAS CAS
,
&
2. After 1 clock cycle, all the inputs including the system clock can be don’t care except for CKE.
3. The device remains in self refresh mode as long as CKE stays “Low”.
(cf.) Once the device enters self refresh mode, minimum tRAS is required before exit from self refresh.
TO EXIT SELF REFRESH MODE
4. System clock restart and be stable before returning CKE high.
5.
starts from high.
CS
6. Minimum tRC is required after CKE going high to complete self refresh exit.
7. 2K cycle of burst auto refresh is required before self refresh entry and after self refresh exit.
If the system uses burst refresh.
PRELIMINARY (July, 2005, Version 0.1)
37
AMIC Technology, Corp.
A43E06161
Mode Register Set Cycle
Auto Refresh Cycle
0
1
2
3
4
5
6
0
1
2
3
4
5
6
7
8
9
10
CLOCK
CKE
High
High
*Note 2
CS
t
RC
RAS
CAS
* Note 1
* Note 3
Key
Ra
ADDR
WE
DQM
DQ
Hi-Z
Hi-Z
MRS
Auto Refresh
New Command
: Don't care
New
Command
* Both banks precharge should be completed before Mode Register Set cycle and auto refresh cycle.
MODE REGISTER SET CYCLE
* Note : 1.
,
,
&
activation at the same clock cycle with address key will set internal mode register.
WE
CS RAS CAS
2. Minimum 2 clock cycles should be met before new
3. Please refer to Mode Register Set table.
activation.
RAS
PRELIMINARY (July, 2005, Version 0.1)
38
AMIC Technology, Corp.
A43E06161
Deep Power Down Mode Entry
CLK
CKE
CS
WE
CAS
RAS
ADDR
DQM
DQ
input
DQ
output
High-Z
t
RP
Precharge Command
Normal Mode
Deep Power Down Entry
Deep Power Down Mode
PRELIMINARY (July, 2005, Version 0.1)
39
AMIC Technology, Corp.
A43E06161
Deep Power Down Mode Exit
CLK
CKE
CS
RAS
CAS
WE
200 us
t
RP
tRC
New
Command
Accepted
Here
Mode
Register Mode
Set Register Set
Extended
Deep Power
Down Exit
All Banks
Precharge Refresh
Auto
Auto
Refresh
The deep power down mode is exited by asserting CKE high. After the exit, the following sequence is needed to enter a new
command:
1. Maintain NOP input conditions for a minimum of 200µs
2. Issue precharge commands for all banks of the device
3. Issue eight or more auto-refresh commands
4. Issue a mode register set command to initialize the mode register
5. Issue an extended mode register set command to initialize the extended mode register
PRELIMINARY (July, 2005, Version 0.1)
40
AMIC Technology, Corp.
A43E06161
Function Truth Table (Table 1)
Current
CS RAS
BA
Address
Action
Note
CAS
WE
State
H
L
L
L
L
L
L
L
H
L
L
L
L
L
L
L
H
L
L
L
L
L
L
L
H
L
L
L
L
L
L
L
H
L
L
L
L
L
L
X
H
H
H
L
X
H
H
L
X
H
L
X
X
X
X
X
NOP
NOP
X
ILLEGAL
2
2
X
H
L
BA
BA
BA
X
CA, A10/AP ILLEGAL
IDLE
H
H
L
RA
Row Active; Latch Row Address
L
PA
NOP
4
5
5
L
H
L
X
Auto Refresh or Self Refresh
L
L
OP Code
Mode Register Access
X
H
H
H
H
L
X
H
H
L
X
H
L
X
X
X
X
X
NOP
NOP
Row
X
ILLEGAL
2
2
Active
H
L
BA
BA
BA
BA
X
CA,A10/AP Begin Read; Latch CA; Determine AP
CA,A10/AP Begin Write; Latch CA; Determine AP
L
H
H
L
H
L
RA
PA
X
ILLEGAL
L
Precharge
L
X
X
H
L
ILLEGAL
X
H
H
H
H
L
X
H
H
L
X
X
NOP(Continue Burst to End →Row Active)
NOP(Continue Burst to End →Row Active)
Term burst →Row Active
X
X
X
X
H
L
BA
BA
BA
BA
X
CA,A10/AP Term burst; Begin Read; Latch CA; Determine AP
3
3
2
3
Read
L
CA,AP
Term burst; Begin Write; Latch CA; Determine AP
ILLEGAL
H
H
L
H
L
RA
PA
X
L
Term Burst; Precharge timing for Reads
ILLEGAL
L
X
X
H
L
X
H
H
H
H
L
X
H
H
L
X
X
NOP(Continue Burst to End→Row Active)
NOP(Continue Burst to End→Row Active)
ILLEGAL
X
X
X
X
H
L
BA
BA
BA
BA
X
CA,A10/AP Term burst; Begin Read; Latch CA; Determine AP
CA,A10/AP Term burst; Begin Read; Latch CA; Determine AP
3
3
2
3
Write
L
H
H
L
H
L
RA
ILLEGAL
L
A10/AP
Term Burst; Precharge timing for Writes
ILLEGAL
L
X
X
H
L
X
X
X
X
X
H
H
H
H
L
X
H
H
L
X
NOP(Continue Burst to End→Precharge)
NOP(Continue Burst to End→Precharge)
ILLEGAL
X
Read with
Auto
Precharge
X
H
L
BA
BA
BA
X
CA,A10/AP ILLEGAL
CA,A10/AP ILLEGAL
2
2
L
H
L
X
X
RA, PA
X
ILLEGAL
ILLEGAL
L
2
PRELIMINARY (July, 2005, Version 0.1)
41
AMIC Technology, Corp.
A43E06161
Function Truth Table (Table 1, Continued)
Current
CS RAS
BA
Address
Action
Note
CAS
WE
State
H
L
L
L
L
L
L
H
L
L
L
L
L
L
H
L
L
L
L
L
L
H
L
L
L
L
X
H
H
H
H
L
X
H
H
L
X
H
L
X
X
X
X
X
NOP(Continue Burst to End→Precharge)
NOP(Continue Burst to End→Precharge)
ILLEGAL
Write with
Auto
X
H
L
BA
BA
BA
X
CA,A10/AP ILLEGAL
CA,A10/AP ILLEGAL
2
2
Precharge
L
H
L
X
X
X
H
L
RA, PA
ILLEGAL
L
X
X
X
X
ILLEGAL
2
X
H
H
H
L
X
H
H
L
X
NOP→Idle after tRP
NOP→Idle after tRP
ILLEGAL
X
X
Precharge
X
H
L
BA
BA
BA
X
CA,A10/AP ILLEGAL
2
2
2
4
H
H
L
RA
PA
X
ILLEGAL
L
NOP→Idle after tRP
ILLEGAL
L
X
X
H
L
X
H
H
H
L
X
H
H
L
X
X
NOP→Row Active after tRCD
NOP→Row Active after tRCD
ILLEGAL
X
X
X
X
Row
Activating
X
H
L
BA
BA
BA
X
CA,A10/AP ILLEGAL
2
2
2
2
H
H
L
RA
PA
X
ILLEGAL
L
ILLEGAL
L
X
X
X
X
X
X
ILLEGAL
X
H
H
L
X
H
L
X
X
NOP→Idle after tRC
NOP→Idle after tRC
ILLEGAL
X
X
Refreshing
X
X
H
L
X
X
ILLEGAL
L
X
X
ILLEGAL
Abbreviations
RA = Row Address
NOP = No Operation Command
BA = Bank Address
AP = Auto Precharge
PA = Precharge All
CA = Column Address
Note: 1. All entries assume that CKE was active (High) during the preceding clock cycle and the current clock cycle.
2. Illegal to bank in specified state : Function may be legal in the bank indicated by BA, depending on the state of that
bank.
3. Must satisfy bus contention, bus turn around, and/or write recovery requirements.
4. NOP to bank precharging or in idle state. May precharge bank indicated by BA (and PA).
5. Illegal if any banks is not idle.
PRELIMINARY (July, 2005, Version 0.1)
42
AMIC Technology, Corp.
A43E06161
Function Truth Table for CKE (Table 2)
Current
State
CKE CKE
CS
RAS
Address
Action
Note
CAS
WE
n-1
n
H
X
X
H
L
X
X
H
H
H
L
X
X
H
H
L
X
X
H
L
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
INVALID
L
L
H
H
H
H
H
L
6
6
Exit Self Refresh→ABI after tRC
Exit Self Refresh→ABI after tRC
ILLEGAL
Self
L
L
Refresh
L
L
X
X
X
X
X
H
L
ILLEGAL
L
L
X
X
X
X
H
H
L
ILLEGAL
L
X
X
H
L
X
X
X
H
H
H
L
NOP(Maintain Self Refresh)
INVALID
H
L
X
H
H
H
H
H
L
7
7
Exit Power Down→ABI
Exit Power Down→ABI
ILLEGAL
Both
Bank
Precharge
Power
L
L
L
L
L
X
X
X
X
X
H
L
ILLEGAL
Down
L
L
X
X
X
X
H
H
L
ILLEGAL
L
X
X
H
L
X
X
X
H
H
H
L
NOP(Maintain Power Down Mode)
Refer to Table 1
H
H
H
H
H
H
H
H
L
H
L
Enter Power Down
Enter Power Down
ILLEGAL
8
8
L
All
Banks
Idle
L
L
L
L
X
X
H
L
ILLEGAL
L
L
H
L
ILLEGAL
L
L
L
Enter Self Refresh
ILLEGAL
8
L
L
L
L
L
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
NOP
H
H
L
H
L
Refer to Operations in Table 1
Begin Clock Suspend next cycle
Exit Clock Suspend next cycle
Maintain clock Suspend
Any State
Other than
Listed
9
9
H
L
Above
L
Abbreviations : ABI = All Banks Idle
Note: 6. After CKE’s low to high transition to exit self refresh mode. And a time of tRC(min) has to be elapse after CKE’s low to
high transition to issue a new command.
7. CKE low to high transition is asynchronous as if restarts internal clock.
A minimum setup time “tSS + one clock” must be satisfied before any command other than exit.
8. Power-down and self refresh can be entered only from the all banks idle state.
9. Must be a legal command.
PRELIMINARY (July, 2005, Version 0.1)
43
AMIC Technology, Corp.
A43E06161
Ordering Information
Part No.
Min. Cycle Time
(ns)
Max. Clock Frequency
(MHz)
Access Time
Package
A43E06161V-75
A43E06161V-75F
A43E06161V-75U
A43E06161V-75UF
A43E06161V-95
A43E06161V-95F
A43E06161V-95U
A43E06161V-95UF
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
133
133
133
133
105
105
105
105
6 ns
6 ns
6 ns
6 ns
7 ns
7 ns
7 ns
7 ns
50 TSOP (II)
50 Pb-Free TSOP (II)
50 TSOP (II)
50 Pb-Free TSOP (II)
50 TSOP (II)
50 Pb-Free TSOP (II)
50 TSOP (II)
50 Pb-Free TSOP (II)
Note: -U is for industrial operating temperature range -40ºC to +85ºC.
PRELIMINARY (July, 2005, Version 0.1)
44
AMIC Technology, Corp.
A43E06161
Package Information
TSOP 50L (Type II) Outline Dimensions
unit: inches/mm
Detail "A"
50
26
R0.15 REF.
R0.15 REF.
θ
L
L
1
1
25
D
Detail "A"
e
b
0.1
Seating Plane
Dimensions in inches
Dimensions in mm
Symbol
Min
-
Nom
Max
0.047
-
Min
-
Nom
Max
1.20
-
A
-
-
A1
A2
b
0.002
0.037
0.012
0.005
0.821
0.455
0.396
-
-
0.05
0.95
0.30
0.12
-
0.040
-
0.041
0.018
0.008
1.016
1.05
0.45
0.21
-
-
c
-
D
E
0.825
0.463
0.400
0.031
0.020
-
0.829 20.855 20.955 21.055
0.471
0.404
-
11.56
10.06
-
11.76
10.16
0.800
0.50
-
11.96
10.26
-
E1
e
L
0.016
0°
0.024
5°
0.40
0°
0.60
5°
θ
Notes:
1. The maximum value of dimension D includes end flash.
2. Dimension E does not include resin fins.
3. Dimension S includes end flash.
PRELIMINARY (July, 2005, Version 0.1)
45
AMIC Technology, Corp.
相关型号：
©2020 ICPDF网 联系我们和版权申明