AM29LV641DL90RWHI [AMD]
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control; 64兆位(4M ×16位) CMOS 3.0伏只统一部门快闪记忆体与VersatileI控制型号: | AM29LV641DL90RWHI |
厂家: | AMD |
描述: | 64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control |
文件: | 总57页 (文件大小:1413K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Am29LV640D/Am29LV641D
Data Sheet
July 2003
The following document specifies Spansion memory products that are now offered by both Advanced
Micro Devices and Fujitsu. Although the document is marked with the name of the company that orig-
inally developed the specification, these products will be offered to customers of both AMD and
Fujitsu.
Continuity of Specifications
There is no change to this datasheet as a result of offering the device as a Spansion product. Any
changes that have been made are the result of normal datasheet improvement and are noted in the
document revision summary, where supported. Future routine revisions will occur when appropriate,
and changes will be noted in a revision summary.
Continuity of Ordering Part Numbers
AMD and Fujitsu continue to support existing part numbers beginning with “Am” and “MBM”. To order
these products, please use only the Ordering Part Numbers listed in this document.
For More Information
Please contact your local AMD or Fujitsu sales office for additional information about Spansion
memory solutions.
Publication Number 22366 Revision B Amendment +8 Issue Date September 20, 2002
Am29LV640D/Am29LV641D
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only
Uniform Sector Flash Memory with VersatileIO Control
DISTINCTIVE CHARACTERISTICS
■ Single power supply operation
■ Compatibility with JEDEC standards
— 3.0 to 3.6 volt read, erase, and program operations
— Pinout and software compatible with single-power
supply Flash
■ VersatileIO control
— Superior inadvertent write protection
— Device generates output voltages and tolerates data
input voltages on the DQ input/ouputs as determined
by the voltage on VIO
■ Minimum 1 million erase cycle guarantee per sector
■ Package options
■ High performance
— 48-pin TSOP (Am29LV641DH/DL only)
— 56-pin SSOP (Am29LV640DH/DL only)
— 63-ball Fine-Pitch BGA (Am29LV640DU only)
— 64-ball Fortified BGA (Am29LV640DU only)
— Access times as fast as 90 ns
■ Manufactured on 0.23 µm process technology
■ CFI (Common Flash Interface) compliant
■ Erase Suspend/Erase Resume
— Provides device-specific information to the system,
allowing host software to easily reconfigure for
different Flash devices
— Suspends an erase operation to read data from, or
program data to, a sect27
■ SecSi (Secured Silicon) Sector region
— or that is not being erased, then resumes the erase
operation
— 128-word sector for permanent, secure identification
through an 8-word random Electronic Serial Number
■ Data# Polling and toggle bits
— May be programmed and locked at the factory or by
— Provides a software method of detecting program or
the customer
erase operation completion
— Accessible through a command sequence
■ Unlock Bypass Program command
■ Ultra low power consumption (typical values at 3.0 V,
— Reduces overall programming time when issuing
5 MHz)
multiple program command sequences
— 9 mA typical active read current
— 26 mA typical erase/program current
— 200 nA typical standby mode current
■ Ready/Busy# pin (RY/BY#) (Am29LV640DU in FBGA
package only)
— Provides a hardware method of detecting program or
■ Flexible sector architecture
erase cycle completion
— One hundred twenty-eight 32 Kword sectors
■ Hardware reset pin (RESET#)
■ Sector Protection
— Hardware method to reset the device for reading array
data
— A hardware method to lock a sector to prevent
program or erase operations within that sector
■ WP# pin (Am29LV641DH/DL in TSOP,
— Sectors can be locked in-system or via programming
Am29LV640DH/DL in SSOP only)
equipment
— At VIL, protects the first or last 32 Kword sector,
— Temporary Sector Unprotect feature allows code
regardless of sector protect/unprotect status
changes in previously locked sectors
— At VIH, allows removal of sector protection
— An internal pull up to VCC is provided
■ Embedded Algorithms
— Embedded Erase algorithm automatically
preprograms and erases the entire chip or any
combination of designated sectors
■ ACC pin
— Accelerates programming time for higher throughput
during system production
— Embedded Program algorithm automatically writes
■ Program and Erase Performance (VHH not applied to
and verifies data at specified addresses
the ACC input pin)
— Word program time: 11 µs typical
— Sector erase time: 0.9 s typical for each 32 Kword
sector
Publication# 22366 Rev: B Amendment/+8
Issue Date: September 20, 2002
Refer to AMD’s Website (www.amd.com) for the latest information.
GENERAL DESCRIPTION
The Am29LV640DU/Am29LV641DU is a 64 Mbit, 3.0
Volt (3.0 V to 3.6 V) single power supply flash memory
devices organized as 4,194,304 words. Data appears
on DQ0-DQ15. The device is designed to be pro-
grammed in-system with the standard system 3.0 volt
VCC supply. A 12.0 volt VPP is not required for program
or erase operations. The device can also be pro-
grammed in standard EPROM programmers.
gle) status bits. After a program or erase cycle has
been completed, the device is ready to read array data
or accept another command.
The sector erase architecture allows memory sec-
tors to be erased and reprogrammed without affecting
the data contents of other sectors. The device is fully
erased when shipped from the factory.
Hardware data protection measures include a low
VCC detector that automatically inhibits write opera-
tions during power transitions. The hardware sector
protection feature disables both program and erase
operations in any combination of sectors of memory.
This can be achieved in-system or via programming
equipment.
Access times of 90 and 120 ns are available for appli-
cations where VIO ≥ VCC. Access times of 100 and 120
ns are available for applications where VIO < VCC. The
device is offered in 48-pin TSOP, 56-pin SSOP, 63-ball
Fine-Pitch BGA and 64-ball Fortified BGA packages.
To eliminate bus contention each device has separate
chip enable (CE#), write enable (WE#) and output en-
able (OE#) controls.
The Erase Suspend/Erase Resume feature enables
the user to put erase on hold for any period of time to
read data from, or program data to, any sector that is
not selected for erasure. True background erase can
thus be achieved.
Each device requires only a single 3.0 Volt power
supply (3.0 V to 3.6 V) for both read and write func-
tions. Internally generated and regulated voltages are
provided for the program and erase operations.
The hardware RESET# pin terminates any operation
in progress and resets the internal state machine to
reading array data. The RESET# pin may be tied to
the system reset circuitry. A system reset would thus
also reset the device, enabling the system micropro-
cessor to read boot-up firmware from the Flash mem-
ory device.
The device is entirely command set compatible with
the JEDEC single-power-supply Flash standard.
Commands are written to the command register using
standard microprocessor write timing. Register con-
tents serve as inputs to an internal state-machine that
controls the erase and programming circuitry. Write
cycles also internally latch addresses and data
needed for the programming and erase operations.
Reading data out of the device is similar to reading
from other Flash or EPROM devices.
The device offers a standby mode as a power-saving
feature. Once the system places the device into the
standby mode power consumption is greatly reduced.
Device programming occurs by executing the program
command sequence. This initiates the Embedded
Program algorithm—an internal algorithm that auto-
matically times the program pulse widths and verifies
proper cell margin. The Unlock Bypass mode facili-
tates faster programming times by requiring only two
write cycles to program data instead of four.
The SecSi (Secured Silicon) Sector provides an
minimum 128-word area for code or data that can be
permanently protected. Once this sector is protected,
no further programming or erasing within the sector
can occur.
The Write Protect (WP#) feature protects the first or
last sector by asserting a logic low on the WP# pin.
The protected sector will still be protected even during
accelerated programming.
Device erasure occurs by executing the erase com-
mand sequence. This initiates the Embedded Erase
algorithm—an internal algorithm that automatically
preprograms the array (if it is not already pro-
grammed) before executing the erase operation. Dur-
ing erase, the device automatically times the erase
pulse widths and verifies proper cell margin.
The accelerated program (ACC) feature allows the
system to program the device at a much faster rate.
When ACC is pulled high to VHH, the device enters the
Unlock Bypass mode, enabling the user to reduce the
time needed to do the program operation. This feature
is intended to increase factory throughput during sys-
tem production, but may also be used in the field if de-
sired.
The VersatileIO™ (VIO) control allows the host system
to set the voltage levels that the device generates and
tolerates on CE# and DQ I/Os to the same voltage
level that is asserted on VIO. VIO is available in two
configurations (1.8–2.9 V and 3.0–5.0 V) for operation
in various system environments.
AMD’s Flash technology combines years of Flash
memory manufacturing experience to produce the
highest levels of quality, reliability and cost effective-
ness. The device electrically erases all bits within a
sector simultaneously via Fowler-Nordheim tunnelling.
The data is programmed using hot electron injection.
The host system can detect whether a program or
erase operation is complete by observing the RY/BY#
pin, by reading the DQ7 (Data# Polling), or DQ6 (tog-
2
Am29LV640D/Am29LV641D
September 20, 2002
TABLE OF CONTENTS
Product Selector Guide . . . . . . . . . . . . . . . . . . . . . 4
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . 5
Special Handling Instructions for FBGA/fBGA Packages .........8
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Ordering Information . . . . . . . . . . . . . . . . . . . . . . 10
Device Bus Operations . . . . . . . . . . . . . . . . . . . . . 11
Table 1. Device Bus Operations .....................................................11
RY/BY#: Ready/Busy# ............................................................ 31
DQ6: Toggle Bit I ....................................................................31
Figure 6. Toggle Bit Algorithm........................................................ 31
DQ2: Toggle Bit II ................................................................... 32
Reading Toggle Bits DQ6/DQ2 ...............................................32
DQ5: Exceeded Timing Limits ................................................ 32
DQ3: Sector Erase Timer ....................................................... 32
Table 11. Write Operation Status ................................................... 33
Absolute Maximum Ratings . . . . . . . . . . . . . . . . 34
Figure 7. Maximum Negative Overshoot Waveform ..................... 34
Figure 8. Maximum Positive Overshoot Waveform....................... 34
Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . 34
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 9. ICC1 Current vs. Time (Showing
Active and Automatic Sleep Currents) ........................................... 36
Figure 10. Typical ICC1 vs. Frequency............................................ 36
Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 11. Test Setup.................................................................... 37
Table 12. Test Specifications ......................................................... 37
Key to Switching Waveforms. . . . . . . . . . . . . . . . 37
Figure 12. Input Waveforms and
Measurement Levels...................................................................... 37
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 38
Read-Only Operations ...........................................................38
Figure 13. Read Operation Timings ............................................... 38
Hardware Reset (RESET#) .................................................... 39
Figure 14. Reset Timings ............................................................... 39
Erase and Program Operations ..............................................40
Figure 15. Program Operation Timings.......................................... 41
Figure 16. Accelerated Program Timing Diagram.......................... 41
Figure 17. Chip/Sector Erase Operation Timings .......................... 42
Figure 18. Data# Polling Timings
VersatileIO (V ) Control ..................................................... 11
IO
Requirements for Reading Array Data ...................................11
Writing Commands/Command Sequences ............................12
Accelerated Program Operation ......................................................12
Autoselect Functions .......................................................................12
Standby Mode ........................................................................ 12
Automatic Sleep Mode ...........................................................12
RESET#: Hardware Reset Pin ...............................................12
Output Disable Mode .............................................................. 13
Table 2. Sector Address Table ........................................................13
Autoselect Mode ..................................................................... 17
Table 3. Autoselect Codes, (High Voltage Method) .......................17
Sector Group Protection and Unprotection ............................. 18
Table 4. Sector Group Protection/Unprotection Address Table .....18
Write Protect (WP#) ................................................................19
Temporary Sector Group Unprotect ....................................... 19
Figure 1. Temporary Sector Group Unprotect Operation................ 19
Figure 2. In-System Sector Group Protect/Unprotect Algorithms ... 20
SecSi (Secured Silicon) Sector Flash Memory Region .......... 21
Table 5. SecSi Sector Contents ......................................................21
Hardware Data Protection ......................................................21
Low VCC Write Inhibit .....................................................................21
Write Pulse “Glitch” Protection ........................................................22
Logical Inhibit ..................................................................................22
Power-Up Write Inhibit ....................................................................22
Common Flash Memory Interface (CFI). . . . . . . 22
Table 6. CFI Query Identification String.......................................... 22
System Interface String................................................................... 23
Table 8. Device Geometry Definition .............................................. 23
Table 9. Primary Vendor-Specific Extended Query ........................ 24
Command Definitions . . . . . . . . . . . . . . . . . . . . . 24
Reading Array Data ................................................................24
Reset Command .....................................................................25
Autoselect Command Sequence ............................................25
Enter SecSi Sector/Exit SecSi Sector Command Sequence ..25
Word Program Command Sequence .....................................25
Unlock Bypass Command Sequence ..............................................26
Figure 3. Program Operation .......................................................... 26
Chip Erase Command Sequence ........................................... 26
Sector Erase Command Sequence ........................................27
Erase Suspend/Erase Resume Commands ........................... 27
Figure 4. Erase Operation............................................................... 28
Command Definitions ............................................................. 29
Command Definitions...................................................................... 29
Write Operation Status . . . . . . . . . . . . . . . . . . . . . 30
DQ7: Data# Polling ................................................................. 30
Figure 5. Data# Polling Algorithm ................................................... 30
(During Embedded Algorithms)...................................................... 43
Figure 19. Toggle Bit Timings
(During Embedded Algorithms)...................................................... 44
Figure 20. DQ2 vs. DQ6................................................................. 44
Temporary Sector Unprotect .................................................. 45
Figure 21. Temporary Sector Group Unprotect Timing Diagram ... 45
Figure 22. Sector Group Protect and Unprotect Timing Diagram .. 46
Alternate CE# Controlled Erase and Program Operations ..... 47
Figure 23. Alternate CE# Controlled Write
(Erase/Program) Operation Timings .............................................. 48
Erase And Programming Performance . . . . . . . 49
Latchup Characteristics. . . . . . . . . . . . . . . . . . . . 49
TSOP Pin Capacitance . . . . . . . . . . . . . . . . . . . . . 49
Data Retention. . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . 50
SSO056—56-Pin Shrink Small Outline Package (SSOP) ......50
FBE063—63-Ball Fine-Pitch Ball Grid Array
(FBGA) 12 x 11 mm package .................................................51
LAA064—64-Ball Fortified Ball Grid Array
(FBGA) 13 x 11 mm package .................................................52
TS 048—48-Pin Standard TSOP ............................................53
TSR048—48-Pin Reverse TSOP ........................................... 54
Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 55
September 20, 2002
Am29LV640D/Am29LV641D
3
PRODUCT SELECTOR GUIDE
Part Number
Am29LV640D/Am29LV641D
VCC = 3.0–3.6 V, VIO = 3.0–5.0 V
VCC = 3.0–3.6 V, VIO = 1.8–2.9 V
90R
120R
121R
120
Speed Option
101R
100
100
35
Max Access Time (ns)
CE# Access Time (ns)
OE# Access Time (ns)
90
90
35
120
50
Note: See “AC Characteristics” for full specifications.
BLOCK DIAGRAM
DQ0–DQ15
RY/BY# (Note 1)
VCC
Sector Switches
VSS
VIO
Erase Voltage
Generator
Input/Output
RESET#
Buffers
WE#
State
WP#
Control
(Note 2)
Command
Register
ACC
PGM Voltage
Generator
Data
Latch
Chip Enable
Output Enable
Logic
STB
CE#
OE#
Y-Decoder
Y-Gating
STB
VCC Detector
Timer
Cell Matrix
X-Decoder
A0–A21
Notes:
1. RY/BY# is only available in the FBGA package.
2. WP# is only available in the TSOP and SSOP packages.
4
Am29LV640D/Am29LV641D
September 20, 2002
CONNECTION DIAGRAMS
A15
A14
A13
A12
A11
A10
A9
1
2
3
4
5
6
7
8
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A16
VIO
VSS
DQ15
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
A8
48-Pin Standard TSOP
(Am29LV641DH/DL only)
A21
A20
WE#
RESET#
ACC
WP#
A19
A18
A17
A7
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
A6
A5
A4
A3
A2
A1
OE#
VSS
CE#
A0
A16
VIO
1
2
3
4
5
6
7
8
48
A15
A14
A13
A12
A11
A10
A9
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
VSS
DQ15
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
A8
48-Pin Reverse TSOP
(Am29LV641DH/DL only)
9
A21
A20
WE#
RESET#
ACC
WP#
A19
A18
A17
A7
A6
A5
A4
A3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
OE#
VSS
CE#
A0
A2
A1
September 20, 2002
Am29LV640D/Am29LV641D
5
CONNECTION DIAGRAMS
ACC
WP#
A19
A18
A17
A7
1
2
3
4
5
6
7
8
9
56 RESET#
55 WE#
54 A20
53 A21
52 A8
51 A9
A6
50 A10
49 A11
48 A12
47 A13
46 A14
45 A15
44 NC
A5
A4
A3 10
A2 11
A1 12
56-Pin SSOP
(Am29LV640DH/DL
only)
NC 13
NC 14
43 NC
NC 15
42 NC
NC 16
41 NC
A0 17
40 A16
39 VIO
CE# 18
VSS 19
OE# 20
DQ0 21
DQ8 22
DQ1 23
DQ9 24
DQ2 25
DQ10 26
DQ3 27
DQ11 28
38 VSS
37 DQ15
36 DQ7
35 DQ14
34 DQ6
33 DQ13
32 DQ5
31 DQ12
30 DQ4
29 VCC
6
Am29LV640D/Am29LV641D
September 20, 2002
CONNECTION DIAGRAM
63-Ball Fine-Pitch BGA (FBGA)
Top View, Balls Facing Down
(Am29LV640DU only)
L8
M8
A8
B8
NC
NC
NC*
NC*
A7
B7
C7
D7
E7
F7
G7
H7
J7
K7
L7
M7
VSS
NC
NC
NC*
NC*
A13
A12
A14
A15
A16
VIO
DQ15
C6
A9
D6
A8
E6
F6
G6
H6
J6
K6
A10
A11
DQ7
DQ14
DQ13
DQ6
C5
D5
E5
F5
G5
H5
J5
K5
VCC
WE# RESET#
A21
A19
DQ5
DQ12
DQ4
C4
D4
E4
F4
G4
H4
J4
K4
RY/BY#
ACC
A18
A20
DQ2
DQ10
DQ11
DQ3
C3
A7
D3
E3
A6
F3
A5
G3
H3
J3
K3
A17
DQ0
DQ8
DQ9
DQ1
C2
A3
D2
A4
E2
A2
F2
A1
G2
A0
H2
J2
K2
L2
M2
A2
VSS
CE#
OE#
NC*
NC*
NC*
A1
B1
L1
M1
* Balls are shorted together via the substrate but not connected to the die.
NC*
NC*
NC*
NC*
September 20, 2002
Am29LV640D/Am29LV641D
7
CONNECTION DIAGRAMS
64-Ball Fortified BGA (FBGA)
Top View, Balls Facing Down
(Am29LV640DU only)
A8
B8
C8
D8
E8
F8
G8
H8
RFU
RFU
RFU
VIO
VSS
RFU
RFU
RFU
A7
B7
C7
D7
E7
F7
G7
H7
A13
A12
A14
A15
A16
NC
DQ15
VSS
A6
A9
B6
A8
C6
D6
E6
F6
G6
H6
DQ6
A10
A11
DQ7
DQ14
DQ13
A5
B5
C5
D5
E5
F5
G5
H5
WE# RESET#
A21
A19
DQ5
DQ12
VCC
DQ4
A4
B4
C4
D4
E4
F4
G4
H4
RY/BY#
ACC
A18
A20
DQ2
DQ10
DQ11
DQ3
A3
A7
B3
C3
A6
D3
A5
E3
F3
G3
H3
A17
DQ0
DQ8
DQ9
DQ1
A2
A3
B2
A4
C2
A2
D2
A1
E2
A0
F2
G2
H2
CE#
OE#
VSS
A1
B1
C1
D1
E1
F1
G1
H1
RFU
RFU
RFU
RFU
RFU
VIO
RFU
RFU
Flash memory devices in BGA packages may be
damaged if exposed to ultrasonic cleaning methods.
The package and/or data integrity may be compromised
if the package body is exposed to temperatures above
150°C for prolonged periods of time.
Special Handling Instructions for
FBGA/fBGA Packages
Special handling is required for Flash Memory products
in BGA packages.
8
Am29LV640D/Am29LV641D
September 20, 2002
PIN DESCRIPTION
LOGIC SYMBOL
A0–A21
= 22 Addresses inputs
22
DQ0–DQ15 = 16 Data inputs/outputs
A0–A21
16
CE#
OE#
WE#
WP#
= Chip Enable input
= Output Enable input
= Write Enable input
DQ0–DQ15
CE#
OE#
WE#
WP#
ACC
= Hardware Write Protect input (N/A on
FBGA)
ACC
= Acceleration Input
RESET#
RY/BY#
VCC
= Hardware Reset Pin input
= Ready/Busy output (FBGA only)
RESET#
VIO
RY/BY#
= 3.0 volt-only single power supply
(see Product Selector Guide for
speed options and voltage
supply tolerances)
Note: WP# is not available on the FBGA package. RY/BY#
is not available on the TSOP and SSOP packages.
VIO
VSS
NC
= Output Buffer power
= Device Ground
= Pin Not Connected Internally
September 20, 2002
Am29LV640D/Am29LV641D
9
ORDERING INFORMATION
Standard Products
AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is
formed by a combination of the following:
Am29LV640D
Am29LV641D
H
90R
E
I
N
OPTIONAL PROCESSING
Blank= Standard Processing
N
=
32-byte ESN devices
(Contact an AMD representative for more information)
TEMPERATURE RANGE
I
=
=
Industrial (–40°C to +85°C)
Extended (–55°C to +125°C)
E
PACKAGE TYPE
E
=
=
=
=
48-Pin Thin Small Outline Package (TSOP) Standard Pinout (TS 048)
48-Pin Thin Small Outline Package (TSOP) Reverse Pinout (TSR048)
56-Pin Shrink Small Outline Package (SSO056)
F
Z
PC
64-Ball Fortified Ball Grid Array (FBGA),
1.0 mm pitch, 13 x 11 mm package (LAA064)
WH
=
63-Ball Fine-Pitch Ball Grid Array (FBGA)
0.80 mm pitch, 11 x 12 mm package (FBE063)
SPEED OPTION
See Product Selector Guide and Valid Combinations
SECTOR ARCHITECTURE AND SECTOR WRITE PROTECTION (WP# = 0)
H
L
=
=
=
Uniform sector device, highest address sector protected
Uniform sector device, lowest address sector protected
Uniform sector device (WP# not available)
U
DEVICE NUMBER/DESCRIPTION
Am29LV640DU/DH/DL, Am29LV641DH/DL
64 Megabit (4 M x 16-Bit) CMOS Uniform Sector Flash Memory with VersatileIO Control
3.0 Volt-only Read, Program, and Erase
Valid Combinations for
TSOP and SSOP Packages
Valid Combinations for BGA Packages
Package
Speed/
IO Range
Speed/VIO Range
V
AM29LV640DH90R,
90ns,
Order Number
Marking
PCI L640DU90N
WHI L640DU90R
PCI L640DU01N
WHI L640DU01R
AM29LV640DL90R
V
V
V
V
V
V
V
V
IO = 3.0 V – 5.0 V
90 ns, VIO
3.0 V – 5.0 V
=
ZI
EI, FI
AM29LV640DU90R
AM29LV640DH101R,
AM29LV640DL101R
100 ns,
IO = 1.8 V – 2.9 V
I
100 ns, VIO
1.8 V – 2.9 V
=
AM29LV641DH90R,
AM29LV641DL90R
90 ns
IO = 3.0 V – 5.0 V
AM29LV640DU101R
AM29LV640DU120R
PCI,
AM29LV641DH101R,
AM29LV641DL101R
100 ns
IO = 1.8 V – 2.9 V
L640DU12N
PCE
120 ns, VIO
3.0 V – 5.0 V
=
WHI,
AM29LV640DH120R,
AM29LV640DL120R
120 ns,
IO = 3.0 V – 5.0 V
L640DU12R
WHE
I,
E
ZI, ZE
PCI,
AM29LV640DH121R,
AM29LV640DL121R
120 ns,
IO = 1.8 V – 2.9 V
L640DU21N
PCE
120 ns, VIO
1.8 V – 2.9 V
=
AM29LV640DU121R
WHI,
AM29LV641DH120R,
AM29LV641DL120R
120 ns,
IO = 3.0 V – 5.0 V
L640DU21R
WHE
EI, FI, EE, FE
Note: LV640DU has RY/BY#, but no WP#.
AM29LV641DH121R,
AM29LV641DL121R
120 ns
IO = 1.8 V – 2.9 V
Valid Combinations
Note: LV640/641DH & DL have WP#, but no RY/BY#. U
Valid Combinations list configurations planned to be supported in vol-
ume for this device. Consult the local AMD sales office to confirm
availability of specific valid combinations and to check on newly re-
leased combinations.
designator in base part number replaced by H or L.
10
Am29LV640D/Am29LV641D
September 20, 2002
DEVICE BUS OPERATIONS
This section describes the requirements and use of
the device bus operations, which are initiated through
the internal command register. The command register
itself does not occupy any addressable memory loca-
tion. The register is a latch used to store the com-
mands, along with the address and data information
needed to execute the command. The contents of the
register serve as inputs to the internal state machine.
The state machine outputs dictate the function of the
device. Table 1 lists the device bus operations, the in-
puts and control levels they require, and the resulting
output. The following subsections describe each of
these operations in further detail.
Table 1. Device Bus Operations
Addresses
(Note 2)
DQ0–
DQ15
Operation
CE# OE# WE# RESET#
WP#
X
ACC
X
Read
L
L
L
H
H
H
L
L
H
H
AIN
AIN
AIN
DOUT
Write (Program/Erase)
Accelerated Program
(Note 3)
(Note 3)
X
(Note 4)
(Note 4)
L
H
VHH
VCC
0.3 V
±
VCC ±
0.3 V
Standby
X
X
X
H
X
High-Z
Output Disable
Reset
L
H
X
H
X
H
L
X
X
X
X
X
X
High-Z
High-Z
X
SA, A6 = L,
A1 = H, A0 = L
Sector Group Protect (Note 2)
L
L
H
H
X
L
L
X
VID
VID
VID
H
H
H
X
X
X
(Note 4)
(Note 4)
(Note 4)
Sector Group Unprotect
(Note 2)
SA, A6 = H,
A1 = H, A0 = L
Temporary Sector Group
Unprotect
X
AIN
Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 8.5–12.5 V, VHH = 11.5–12.5 V, X = Don’t Care, SA = Sector Address,
AIN = Address In, DIN = Data In, DOUT = Data Out
Notes:
1. Addresses are A21:A0. Sector addresses are A21:A15.
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the “Sector Group
Protection and Unprotection” section.
3. If WP# = VIL, the first or last sector remains protected. If WP# = VIH, the first or last sector will be protected or unprotected as
determined by the method described in “Sector Group Protection and Unprotection”. All sectors are unprotected when shipped
from the factory (The SecSi Sector may be factory protected depending on version ordered.)
4. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm (see Figure 2).
VersatileIO (VIO) Control
Requirements for Reading Array Data
The VersatileIO™ (VIO) control allows the host system
to set the voltage levels that the device generates and
tolerates on CE# and DQ I/Os to the same voltage
level that is asserted on VIO. VIO is available in two
configurations (1.8–2.9 V and 3.0–5.0 V) for operation
in various system environments.
To read array data from the outputs, the system must
drive the CE# and OE# pins to VIL. CE# is the power
control and selects the device. OE# is the output con-
trol and gates array data to the output pins. WE#
should remain at VIH.
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory
content occurs during the power transition. No com-
mand is necessary in this mode to obtain array data.
Standard microprocessor read cycles that assert valid
addresses on the device address inputs produce valid
For example, a VI/O of 4.5–5.0 volts allows for I/O at
the 5 volt level, driving and receiving signals to and
from other 5 V devices on the same data bus.
September 20, 2002
Am29LV640D/Am29LV641D
11
data on the device data outputs. The device remains
enabled for read access until the command register
contents are altered.
lect Command Sequence sections for more informa-
tion.
Standby Mode
See “Requirements for Reading Array Data” for more
information. Refer to the AC Read-Only Operations
table for timing specifications and to Figure 13 for the
timing diagram. ICC1 in the DC Characteristics table
represents the active current specification for reading
array data.
When the system is not reading or writing to the de-
vice, it can place the device in the standby mode. In
this mode, current consumption is greatly reduced,
and the outputs are placed in the high impedance
state, independent of the OE# input.
The device enters the CMOS standby mode when the
CE# and RESET# pins are both held at VCC ± 0.3 V.
(Note that this is a more restricted voltage range than
VIH.) If CE# and RESET# are held at VIH, but not within
VCC ± 0.3 V, the device will be in the standby mode,
but the standby current will be greater. The device re-
quires standard access time (tCE) for read access
when the device is in either of these standby modes,
before it is ready to read data.
Writing Commands/Command Sequences
To write a command or command sequence (which in-
cludes programming data to the device and erasing
sectors of memory), the system must drive WE# and
CE# to VIL, and OE# to VIH.
The device features an Unlock Bypass mode to facil-
itate faster programming. Once the device enters the
Unlock Bypass mode, only two write cycles are re-
quired to program a word or byte, instead of four. The
“Word Program Command Sequence” section has de-
tails on programming data to the device using both
standard and Unlock Bypass command sequences.
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
ICC3 in the DC Characteristics table represents the
standby current specification.
An erase operation can erase one sector, multiple sec-
tors, or the entire device. Table 2 indicates the address
space that each sector occupies.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device en-
ergy consumption. The device automatically enables
ICC2 in the DC Characteristics table represents the ac-
tive current specification for the write mode. The AC
Characteristics section contains timing specification
tables and timing diagrams for write operations.
this mode when addresses remain stable for tACC
+
30 ns. The automatic sleep mode is independent of
the CE#, WE#, and OE# control signals. Standard ad-
dress access timings provide new data when ad-
dresses are changed. While in sleep mode, output
data is latched and always available to the system.
ICC4 in the DC Characteristics table represents the
automatic sleep mode current specification.
Accelerated Program Operation
The device offers accelerated program operations
through the ACC function. This function is primarily in-
tended to allow faster manufacturing throughput dur-
ing system production.
If the system asserts VHH on this pin, the device auto-
matically enters the aforementioned Unlock Bypass
mode, temporarily unprotects any protected sectors,
and uses the higher voltage on the pin to reduce the
time required for program operations. The system
would use a two-cycle program command sequence
as required by the Unlock Bypass mode. Removing
VHH from the ACC pin returns the device to normal op-
eration. Note that the ACC pin must not be at VHH for
operations other than accelerated programming, or
device damage may result.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of re-
setting the device to reading array data. When the RE-
SET# pin is driven low for at least a period of tRP, the
device immediately terminates any operation in
progress, tristates all output pins, and ignores all
read/write commands for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is
ready to accept another command sequence, to en-
sure data integrity.
Autoselect Functions
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at VSS±0.3 V, the device
draws CMOS standby current (ICC4). If RESET# is held
at VIL but not within VSS±0.3 V, the standby current will
be greater.
If the system writes the autoselect command se-
quence, the device enters the autoselect mode. The
system can then read autoselect codes from the inter-
nal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in
this mode. Refer to the Autoselect Mode and Autose-
12
Am29LV640D/Am29LV641D
September 20, 2002
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firm-
ware from the Flash memory.
pleted within a time of tREADY (not during Embedded
Algorithms). The system can read data tRH after the
RESET# pin returns to VIH.
Refer to the AC Characteristics tables for RESET# pa-
rameters and to Figure 14 for the timing diagram.
If RESET# is asserted during a program or erase op-
eration, the RY/BY# pin remains a “0” (busy) until the
internal reset operation is complete, which requires a
time of tREADY (during Embedded Algorithms). The
system can thus monitor RY/BY# to determine
whether the reset operation is complete. If RESET# is
asserted when a program or erase operation is not ex-
ecuting (RY/BY# pin is “1”), the reset operation is com-
Output Disable Mode
When the OE# input is at VIH, output from the device is
disabled. The output pins are placed in the high
impedance state.
Table 2. Sector Address Table
16-bit Address Range
(in hexadecimal)
Sector
SA0
A21
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
A20
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
A19
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
A18
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
A17
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
A16
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
A15
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
000000–007FFF
008000–00FFFF
010000–017FFF
018000–01FFFF
020000–027FFF
028000–02FFFF
030000–037FFF
038000–03FFFF
040000–047FFF
048000–04FFFF
050000–057FFF
058000–05FFFF
060000–067FFF
068000–06FFFF
070000–077FFF
078000–07FFFF
080000–087FFF
088000–08FFFF
090000–097FFF
098000–09FFFF
0A0000–0A7FFF
0A8000–0AFFFF
0B0000–0B7FFF
0B8000–0BFFFF
0C0000–0C7FFF
0C8000–0CFFFF
SA1
SA2
SA3
SA4
SA5
SA6
SA7
SA8
SA9
SA10
SA11
SA12
SA13
SA14
SA15
SA16
SA17
SA18
SA19
SA20
SA21
SA22
SA23
SA24
SA25
September 20, 2002
Am29LV640D/Am29LV641D
13
Table 2. Sector Address Table (Continued)
16-bit Address Range
(in hexadecimal)
Sector
SA26
SA27
SA28
SA29
SA30
SA31
SA32
SA33
SA34
SA35
SA36
SA37
SA38
SA39
SA40
SA41
SA42
SA43
SA44
SA45
SA46
SA47
SA48
SA49
SA50
SA51
SA52
SA53
SA54
SA55
SA56
SA57
SA58
SA59
SA60
A21
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
A20
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
A19
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
A18
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
A17
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
A16
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
A15
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0D0000–0D7FFF
0D8000–0DFFFF
0E0000–0E7FFF
0E8000–0EFFFF
0F0000–0F7FFF
0F8000–0FFFFF
100000–107FFF
108000–10FFFF
110000–117FFF
118000–11FFFF
120000–127FFF
128000–12FFFF
130000–137FFF
138000–13FFFF
140000–147FFF
148000–14FFFF
150000–157FFF
158000–15FFFF
160000–167FFF
168000–16FFFF
170000–177FFF
178000–17FFFF
180000–187FFF
188000–18FFFF
190000–197FFF
198000–19FFFF
1A0000–1A7FFF
1A8000–1AFFFF
1B0000–1B7FFF
1B8000–1BFFFF
1C0000–1C7FFF
1C8000–1CFFFF
1D0000–1D7FFF
1D8000–1DFFFF
1E0000–1E7FFF
14
Am29LV640D/Am29LV641D
September 20, 2002
Table 2. Sector Address Table (Continued)
16-bit Address Range
(in hexadecimal)
Sector
SA61
SA62
SA63
SA64
SA65
SA66
SA67
SA68
SA69
SA70
SA71
SA72
SA73
SA74
SA75
SA76
SA77
SA78
SA79
SA80
SA81
SA82
SA83
SA84
SA85
SA86
SA87
SA88
SA89
SA90
SA91
SA92
SA93
SA94
SA95
A21
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
A20
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
A19
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
A18
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
A17
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
A16
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
A15
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1E8000–1EFFFF
1F0000–1F7FFF
1F8000–1FFFFF
200000–207FFF
208000–20FFFF
210000–217FFF
218000–21FFFF
220000–227FFF
228000–22FFFF
230000–237FFF
238000–23FFFF
240000–247FFF
248000–24FFFF
250000–257FFF
258000–25FFFF
260000–267FFF
268000–26FFFF
270000–277FFF
278000–27FFFF
280000–287FFF
288000–28FFFF
290000–297FFF
298000–29FFFF
2A0000–2A7FFF
2A8000–2AFFFF
2B0000–2B7FFF
2B8000–2BFFFF
2C0000–2C7FFF
2C8000–2CFFFF
2D0000–2D7FFF
2D8000–2DFFFF
2E0000–2E7FFF
2E8000–2EFFFF
2F0000–2F7FFF
2F8000–2FFFFF
September 20, 2002
Am29LV640D/Am29LV641D
15
Table 2. Sector Address Table (Continued)
16-bit Address Range
(in hexadecimal)
Sector
SA96
A21
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
A20
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
A19
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
A18
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
A17
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
A16
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
A15
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
300000–307FFF
308000–30FFFF
310000–317FFF
318000–31FFFF
320000–327FFF
328000–32FFFF
330000–337FFF
338000–33FFFF
340000–347FFF
348000–34FFFF
350000–357FFF
358000–35FFFF
360000–367FFF
368000–36FFFF
370000–377FFF
378000–37FFFF
380000–387FFF
388000–38FFFF
390000–397FFF
398000–39FFFF
3A0000–3A7FFF
3A8000–3AFFFF
3B0000–3B7FFF
3B8000–3BFFFF
3C0000–3C7FFF
3C8000–3CFFFF
3D0000–3D7FFF
3D8000–3DFFFF
3E0000–3E7FFF
3E8000–3EFFFF
3F0000–3F7FFF
3F8000–3FFFFF
SA97
SA98
SA99
SA100
SA101
SA102
SA103
SA104
SA105
SA106
SA107
SA108
SA109
SA110
SA111
SA112
SA113
SA114
SA115
SA116
SA117
SA118
SA119
SA120
SA121
SA122
SA123
SA124
SA125
SA126
SA127
Note: All sectors are 32 Kwords in size.
16
Am29LV640D/Am29LV641D
September 20, 2002
Table 3. In addition, when verifying sector protection,
the sector address must appear on the appropriate
highest order address bits (see Table 2). Table 3
shows the remaining address bits that are don’t care.
When all necessary bits have been set as required,
the programming equipment may then read the corre-
sponding identifier code on DQ7–DQ0.
Autoselect Mode
The autoselect mode provides manufacturer and de-
vice identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equip-
ment to automatically match a device to be pro-
grammed with its corresponding programming
algorithm. However, the autoselect codes can also be
accessed in-system through the command register.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in Table 10. This method
does not require VID. Refer to the Autoselect Com-
mand Sequence section for more information.
When using programming equipment, the autoselect
mode requires VID (8.5 V to 12.5 V) on address pin A9.
Address pins A6, A1, and A0 must be as shown in
Table 3. Autoselect Codes, (High Voltage Method)
A21
to
A14
to
A8
to
A5
to
Description
CE# OE# WE# A15
A10 A9 A7 A6 A2 A1 A0
DQ15 to DQ0
Manufacturer ID: AMD
L
L
L
L
H
H
X
X
X
X
VID
VID
X
X
L
L
X
X
L
L
L
0001h
Device ID: LV640DU/H/L,
LV641DH/L
H
22D7h
Sector Protection
Verification
XX01h (protected),
XX00h (unprotected)
L
L
L
L
H
H
SA
X
X
X
VID
X
X
L
L
X
X
H
H
L
SecSi Sector Indicator Bit
(DQ7), WP# protects
highest address sector
(LV640DH/641DH), or
no WP# (LV640DU)
XX98h (factory locked),
XX18h (not factory locked)
VID
H
SecSi Sector Indicator Bit
(DQ7), WP# protects
lowest address sector
(LV640DL/641DL)
XX88h (factory locked),
XX08h (not factory locked)
L
L
H
X
X
VID
X
L
X
H
H
Legend: L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care.
September 20, 2002
Am29LV640D/Am29LV641D
17
Table 4. Sector Group Protection/Unprotection
Address Table
Sector Group Protection and
Unprotection
Sector Group
SA0–SA3
A21–A17
00000
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
10001
10010
10011
10100
10101
10110
10111
11000
11001
11010
11011
11100
11101
11110
11111
The hardware sector group protection feature disables
both program and erase operations in any sector
group. In this device, a sector group consists of four
adjacent sectors that are protected or unprotected at
the same time (see Table 4). The hardware sector
group unprotection feature re-enables both program
and erase operations in previously protected sector
groups. Sector group protection/unprotection can be
implemented via two methods.
SA4–SA7
SA8–SA11
SA12–SA15
SA16–SA19
SA20–SA23
SA24–SA27
SA28–SA31
SA32–SA35
SA36–SA39
SA40–SA43
SA44–SA47
SA48–SA51
SA52–SA55
SA56–SA59
SA60–SA63
SA64–SA67
SA68–SA71
SA72–SA75
SA76–SA79
SA80–SA83
SA84–SA87
SA88–SA91
SA92–SA95
SA96–SA99
SA100–SA103
SA104–SA107
SA108–SA111
SA112–SA115
SA116–SA119
SA120–SA123
SA124–SA127
Sector protection/unprotection requires VID on the RE-
SET# pin only, and can be implemented either in-sys-
tem or via programming equipment. Figure 2 shows
the algorithms and Figure 22 shows the timing dia-
gram. This method uses standard microprocessor bus
cycle timing. For sector group unprotect, all unpro-
tected sector groups must first be protected prior to
the first sector group unprotect write cycle.
The device is shipped with all sector groups unpro-
tected. AMD offers the option of programming and
protecting sector groups at its factory prior to shipping
the device through AMD’s ExpressFlash™ Service.
Contact an AMD representative for details.
It is possible to determine whether a sector group is
protected or unprotected. See the Autoselect Mode
section for details.
Note: All sector groups are 128 Kwords in size.
18
Am29LV640D/Am29LV641D
September 20, 2002
Write Protect (WP#)
The Write Protect function provides a hardware
method of protecting the first or last sector without
using VID.
START
If the system asserts VIL on the WP# pin, the device
disables program and erase functions in the first or
last sector independently of whether those sectors
were protected or unprotected using the method de-
scribed in “Sector Group Protection and Unprotection”.
Note that if WP# is at VIL when the device is in the
standby mode, the maximum input load current is in-
creased. See the table in “DC Characteristics”.
RESET# = VID
(Note 1)
Perform Erase or
Program Operations
RESET# = VIH
If the system asserts VIH on the WP# pin, the device
reverts to whether the first or last sector was previ-
ously set to be protected or unprotected using the
method described in “Sector Group Protection and Un-
protection”.
Temporary Sector
Group Unprotect
Completed (Note 2)
Temporary Sector Group Unprotect
(Note: In this device, a sector group consists of four adjacent
sectors that are protected or unprotected at the same time
(see Table 4)).
Notes:
1. All protected sector groups unprotected (If WP# = VIL,
the first or last sector will remain protected).
This feature allows temporary unprotection of previ-
ously protected sector groups to change data in-sys-
tem. The Sector Group Unprotect mode is activated by
setting the RESET# pin to VID (8.5 V – 12.5 V). During
this mode, formerly protected sector groups can be
programmed or erased by selecting the sector group
addresses. Once VID is removed from the RESET#
pin, all the previously protected sector groups are
protected again. Figure 1 shows the algorithm, and
Figure 21 shows the timing diagrams, for this feature.
2. All previously protected sector groups are protected
once again.
Figure 1. Temporary Sector Group
Unprotect Operation
September 20, 2002
Am29LV640D/Am29LV641D
19
START
START
PLSCNT = 1
PLSCNT = 1
RESET# = VID
Protect all sector
groups: The indicated
portion of the sector
group protect algorithm
must be performed for all
unprotected sector
groups prior to issuing
the first sector group
unprotect address
RESET# = VID
Wait 1 µs
Wait 1 µs
Temporary Sector
Group Unprotect
Mode
Temporary Sector
Group Unprotect
Mode
No
First Write
Cycle = 60h?
No
First Write
Cycle = 60h?
Yes
Yes
Set up sector
group address
All sector
groups
No
protected?
Sector Group Protect:
Write 60h to sector
group address with
A6 = 0, A1 = 1,
A0 = 0
Yes
Set up first sector
group address
Sector Group
Unprotect:
Wait 150 µs
Write 60h to sector
group address with
A6 = 1, A1 = 1,
A0 = 0
Verify Sector Group
Protect: Write 40h
to sector group
address twith A6 = 0,
A1 = 1, A0 = 0
Reset
PLSCNT = 1
Increment
PLSCNT
Wait 15 ms
Verify Sector Group
Unprotect: Write
40h to sector group
address with
A6 = 1, A1 = 1,
A0 = 0
Read from
sector group address
with A6 = 0,
A1 = 1, A0 = 0
Increment
PLSCNT
No
No
PLSCNT
= 25?
Read from
sector group
address with A6 = 1,
A1 = 1, A0 = 0
Data = 01h?
Yes
No
Yes
Set up
next sector group
address
Protect
another
sector group?
Yes
No
PLSCNT
= 1000?
Data = 00h?
Yes
Device failed
No
Yes
Remove VID
from RESET#
Last sector
group
verified?
No
Device failed
Write reset
command
Yes
Remove VID
from RESET#
Sector Group
Unprotect
Sector Group
Protect
Sector Group
Protect complete
Write reset
command
Algorithm
Algorithm
Sector Group
Unprotect complete
Figure 2. In-System Sector Group Protect/Unprotect Algorithms
Am29LV640D/Am29LV641D
20
September 20, 2002
vices are then shipped from AMD’s factory with the
SecSi Sector permanently locked. Contact an AMD
representative for details on using AMD’s Express-
Flash service.
SecSi (Secured Silicon) Sector Flash
Memory Region
The SecSi (Secured Silicon) Sector feature provides a
Flash memory region that enables permanent part
identification through an Electronic Serial Number
(ESN). The SecSi Sector is 128 words in length, and
uses a SecSi Sector Indicator Bit (DQ7) to indicate
whether or not the SecSi Sector is locked when
shipped from the factory. This bit is permanently set at
the factory and cannot be changed, which prevents
cloning of a factory locked part. This ensures the secu-
rity of the ESN once the product is shipped to the field.
Customer Lockable: SecSi Sector NOT
Programmed or Protected At the Factory
As an alternative to the factory-locked version, the de-
vice may be ordered such that the customer may pro-
gram and protect the 128-word SecSi sector.
Programming and protecting the SecSi Sector must be
used with caution since, once protected, there is no
procedure available for unprotecting the SecSi Sector
area and none of the bits in the SecSi Sector memory
space can be modified in any way.
AMD offers the device with the SecSi Sector either
factory locked or customer lockable. The fac-
tory-locked version is always protected when shipped
from the factory, and has the SecSi (Secured Silicon)
Sector Indicator Bit permanently set to a “1.” The cus-
tomer-lockable version is shipped with the SecSi Sec-
tor unprotected, allowing customers to utilize that
sector in any manner they choose. The customer-lock-
able version also has the SecSi Sector Indicator Bit
permanently set to a “0.” Thus, the SecSi Sector Indi-
cator Bit prevents customer-lockable devices from
being used to replace devices that are factory locked.
The SecSi Sector area can be protected using one of
the following procedures:
■ Write the three-cycle Enter SecSi Sector Region
command sequence, and then follow the in-system
sector protect algorithm as shown in Figure 2, ex-
cept that RESET# may be at either VIH or VID. This
allows in-system protection of the SecSi Sector
without raising any device pin to a high voltage.
Note that this method is only applicable to the SecSi
Sector.
The SecSi sector address space in this device is allo-
cated as follows:
■ Write the three-cycle Enter SecSi Sector Region
command sequence, and then use the alternate
method of sector protection described in the “Sector
Group Protection and Unprotection” section.
Table 5. SecSi Sector Contents
SecSi Sector
Address Range
Standard
Factory Locked Factory Locked
ExpressFlash
Customer
Lockable
Once the SecSi Sector is programmed, locked and
verified, the system must write the Exit SecSi Sector
Region command sequence to return to reading and
writing within the remainder of the array.
ESN or
determined by
customer
000000h–000007h
000008h–00007Fh
ESN
Determined by
customer
Determined by
customer
Unavailable
The system accesses the SecSi Sector through a
command sequence (see “Enter SecSi Sector/Exit
SecSi Sector Command Sequence”). After the system
has written the Enter SecSi Sector command se-
quence, it may read the SecSi Sector by using the ad-
dresses normally occupied by the first sector (SA0).
This mode of operation continues until the system is-
sues the Exit SecSi Sector command sequence, or
until power is removed from the device. On power-up,
or following a hardware reset, the device reverts to
sending commands to sector SA0.
Hardware Data Protection
The command sequence requirement of unlock cycles
for programming or erasing provides data protection
against inadvertent writes (refer to Table 10 for com-
mand definitions). In addition, the following hardware
data protection measures prevent accidental erasure
or programming, which might otherwise be caused by
spurious system level signals during VCC power-up
and power-down transitions, or from system noise.
Low VCC Write Inhibit
Factory Locked: SecSi Sector Programmed and
Protected At the Factory
When VCC is less than VLKO, the device does not ac-
cept any write cycles. This protects data during VCC
power-up and power-down. The command register
and all internal program/erase circuits are disabled,
and the device resets to the read mode. Subsequent
writes are ignored until VCC is greater than VLKO. The
system must provide the proper signals to the control
pins to prevent unintentional writes when VCC is
In devices with an ESN, the SecSi Sector is protected
when the device is shipped from the factory. The SecSi
Sector cannot be modified in any way. A factory locked
device has an 8-word random ESN at addresses
000000h–000007h.
Customers may opt to have their code programmed by
AMD through the AMD ExpressFlash service. The de-
greater than VLKO
.
September 20, 2002
Am29LV640D/Am29LV641D
21
Write Pulse “Glitch” Protection
CE# and WE# must be a logical zero while OE# is a
logical one.
Noise pulses of less than 5 ns (typical) on OE#, CE#
or WE# do not initiate a write cycle.
Power-Up Write Inhibit
Logical Inhibit
If WE# = CE# = VIL and OE# = VIH during power up,
the device does not accept commands on the rising
edge of WE#. The internal state machine is automati-
cally reset to the read mode on power-up.
Write cycles are inhibited by holding any one of OE# =
VIL, CE# = VIH or WE# = VIH. To initiate a write cycle,
COMMON FLASH MEMORY INTERFACE (CFI)
The Common Flash Interface (CFI) specification out-
lines device and host system software interrogation
handshake, which allows specific vendor-specified
software algorithms to be used for entire families of
devices. Software support can then be device-inde-
pendent, JEDEC ID-independent, and forward- and
backward-compatible for the specified flash device
families. Flash vendors can standardize their existing
interfaces for long-term compatibility.
given in Tables 6–9. To terminate reading CFI data,
the system must write the reset command.
The system can also write the CFI query command
when the device is in the autoselect mode. The device
enters the CFI query mode, and the system can read
CFI data at the addresses given in Tables 6–9. The
system must write the reset command to return the de-
vice to the autoselect mode.
For further information, please refer to the CFI Specifi-
cation and CFI Publication 100, available via the
World Wide Web at http://www.amd.com/prod-
ucts/nvd/overview/cfi.html. Alternatively, contact an
AMD representative for copies of these documents.
This device enters the CFI Query mode when the sys-
tem writes the CFI Query command, 98h, to address
55h, any time the device is ready to read array data.
The system can read CFI information at the addresses
Table 6. CFI Query Identification String
Description
Addresses (x16)
Data
10h
11h
12h
0051h
0052h
0059h
Query Unique ASCII string “QRY”
13h
14h
0002h
0000h
Primary OEM Command Set
15h
16h
0040h
0000h
Address for Primary Extended Table
17h
18h
0000h
0000h
Alternate OEM Command Set (00h = none exists)
Address for Alternate OEM Extended Table (00h = none exists)
19h
1Ah
0000h
0000h
22
Am29LV640D/Am29LV641D
September 20, 2002
Table 7. System Interface String
Description
Addresses (x16)
Data
V
CC Min. (write/erase)
1Bh
0027h
D7–D4: volt, D3–D0: 100 millivolt
VCC Max. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
1Ch
0036h
1Dh
1Eh
1Fh
20h
21h
22h
23h
24h
25h
26h
0000h
0000h
0004h
0000h
000Ah
0000h
0005h
0000h
0004h
0000h
VPP Min. voltage (00h = no VPP pin present)
VPP Max. voltage (00h = no VPP pin present)
Typical timeout per single byte/word write 2N µs
Typical timeout for Min. size buffer write 2N µs (00h = not supported)
Typical timeout per individual block erase 2N ms
Typical timeout for full chip erase 2N ms (00h = not supported)
Max. timeout for byte/word write 2N times typical
Max. timeout for buffer write 2N times typical
Max. timeout per individual block erase 2N times typical
Max. timeout for full chip erase 2N times typical (00h = not supported)
Table 8. Device Geometry Definition
Addresses (x16)
Data
Description
27h
0017h
Device Size = 2N byte
28h
29h
0001h
0000h
Flash Device Interface description (refer to CFI publication 100)
2Ah
2Bh
0000h
0000h
Max. number of byte in multi-byte write = 2N
(00h = not supported)
2Ch
0001h
Number of Erase Block Regions within device
2Dh
2Eh
2Fh
30h
007Fh
0000h
0000h
0001h
Erase Block Region 1 Information
(refer to the CFI specification or CFI publication 100)
31h
32h
33h
34h
0000h
0000h
0000h
0000h
Erase Block Region 2 Information (refer to CFI publication 100)
Erase Block Region 3 Information (refer to CFI publication 100)
Erase Block Region 4 Information (refer to CFI publication 100)
35h
36h
37h
38h
0000h
0000h
0000h
0000h
39h
3Ah
3Bh
3Ch
0000h
0000h
0000h
0000h
September 20, 2002
Am29LV640D/Am29LV641D
23
Table 9. Primary Vendor-Specific Extended Query
Data Description
Addresses (x16)
40h
41h
42h
0050h
0052h
0049h
Query-unique ASCII string “PRI”
43h
44h
0031h
0033h
Major version number, ASCII
Minor version number, ASCII
Address Sensitive Unlock (Bits 1-0)
00b = Required, 01b = Not Required
45h
0000h
Silicon Revision Number (Bits 7-2) 000000b = 0.23 µm Process Technology
Erase Suspend
46h
47h
48h
49h
4Ah
4Bh
4Ch
0002h
0004h
0001h
0004h
0000h
0000h
0000h
00 = Not Supported, 01 = To Read Only, 02 = To Read & Write
Sector Protect
00 = Not Supported, X = Number of sectors in per group
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
Sector Protect/Unprotect scheme
04 = 29LV800A mode
Simultaneous Operation
00 = Not Supported, XX = Number of Sectors in Bank
Burst Mode Type
00 = Not Supported, 01 = Supported
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
ACC (Acceleration) Supply Minimum
4Dh
4Eh
00B5h
00C5h
Bits 7–4 = Hex Value in Volts, Bits 0–3 = BCD Value in 100 mV
ACC (Acceleration) Supply Maximum
Bits 7–4 = Hex Value in Volts, Bits 0–3 = BCD Value in 100 mV
Top/Bottom Boot Sector Flag
00h = Uniform Sector, No WP# Control
04h = Uniform Sector, WP# Protects Bottom Sector
05h = Uniform Sector, WP# Protects Top Sector
4Fh
000Xh
COMMAND DEFINITIONS
Writing specific address and data commands or se-
quences into the command register initiates device op-
erations. Table 10 defines the valid register command
sequences. Writing incorrect address and data val-
ues or writing them in the improper sequence resets
the device to reading array data.
Reading Array Data
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is ready to read array data
after completing an Embedded Program or Embedded
Erase algorithm.
All addresses are latched on the falling edge of WE#
or CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens
first. Refer to the AC Characteristics section for timing
diagrams.
After the device accepts an Erase Suspend command,
the device enters the erase-suspend-read mode, after
which the system can read data from any
non-erase-suspended sector. After completing a pro-
gramming operation in the Erase Suspend mode, the
system may once again read array data with the same
exception. See the Erase Suspend/Erase Resume
Commands section for more information.
24
Am29LV640D/Am29LV641D
September 20, 2002
The system must issue the reset command to return
the device to the read (or erase-suspend-read) mode
if DQ5 goes high during an active program or erase
operation, or if the device is in the autoselect mode.
See the next section, Reset Command, for more infor-
mation.
The autoselect command sequence is initiated by first
writing two unlock cycles. This is followed by a third
write cycle that contains the autoselect command. The
device then enters the autoselect mode. The system
may read at any address any number of times without
initiating another autoselect command sequence:
See also Requirements for Reading Array Data in the
Device Bus Operations section for more information.
The Read-Only Operations table provides the read pa-
rameters, and Figure 13 shows the timing diagram.
■ A read cycle at address XX00h returns the manu-
facturer code.
■ A read cycle at address XX01h returns the device
code.
■ A read cycle to an address containing a sector
group address (SA), and the address 02h on A7–A0
returns 01h if the sector group is protected, or 00h
if it is unprotected. (Refer to Table 4 for valid sector
addresses).
Reset Command
Writing the reset command resets the device to the
read or erase-suspend-read mode. Address bits are
don’t cares for this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to the read
mode. Once erasure begins, however, the device ig-
nores reset commands until the operation is complete.
The system must write the reset command to return to
the read mode (or erase-suspend-read mode if the de-
vice was previously in Erase Suspend).
Enter SecSi Sector/Exit SecSi Sector
Command Sequence
The reset command may be written between the
sequence cycles in a program command sequence
before programming begins. This resets the device to
the read mode. If the program command sequence is
written while the device is in the Erase Suspend mode,
writing the reset command returns the device to the
erase-suspend-read mode. Once programming be-
gins, however, the device ignores reset commands
until the operation is complete.
The SecSi Sector region provides a secured data area
containing an 8-word random Electronic Serial Num-
ber (ESN). The system can access the SecSi Sector
region by issuing the three-cycle Enter SecSi Sector
command sequence. The device continues to access
the SecSi Sector region until the system issues the
four-cycle Exit SecSi Sector command sequence. The
Exit SecSi Sector command sequence returns the de-
vice to normal operation. Table 10 shows the address
and data requirements for both command sequences.
See also “SecSi (Secured Silicon) Sector Flash
Memory Region” for further information.
The reset command may be written between the se-
quence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command
must be written to return to the read mode. If the de-
vice entered the autoselect mode while in the Erase
Suspend mode, writing the reset command returns the
device to the erase-suspend-read mode.
Word Program Command Sequence
Programming is a four-bus-cycle operation. The pro-
gram command sequence is initiated by writing two
unlock write cycles, followed by the program set-up
command. The program address and data are written
next, which in turn initiate the Embedded Program al-
gorithm. The system is not required to provide further
controls or timings. The device automatically provides
internally generated program pulses and verifies the
programmed cell margin. Table 10 shows the address
and data requirements for the byte program command
sequence.
If DQ5 goes high during a program or erase operation,
writing the reset command returns the device to the
read mode (or erase-suspend-read mode if the device
was in Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host
system to access the manufacturer and device codes,
and determine whether or not a sector is protected.
Table 10 shows the address and data requirements.
This method is an alternative to that shown in Table 3,
which is intended for PROM programmers and re-
quires VID on address pin A9. The autoselect com-
mand sequence may be written to an address that is
either in the read or erase-suspend-read mode. The
autoselect command may not be written while the de-
vice is actively programming or erasing.
When the Embedded Program algorithm is complete,
the device then returns to the read mode and ad-
dresses are no longer latched. The system can deter-
mine the status of the program operation by using
DQ7, DQ6, or RY/BY#. Refer to the Write Operation
Status section for information on these status bits.
Any commands written to the device during the Em-
bedded Program Algorithm are ignored. Note that a
September 20, 2002
Am29LV640D/Am29LV641D
25
hardware reset immediately terminates the program
operation. The program command sequence should
be reinitiated once the device has returned to the read
mode, to ensure data integrity.
table in the AC Characteristics section for parameters,
and Figure 15 for timing diagrams.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed
from “0” back to a “1.” Attempting to do so may
cause the device to set DQ5 = 1, or cause the DQ7
and DQ6 status bits to indicate the operation was suc-
cessful. However, a succeeding read will show that the
data is still “0.” Only erase operations can convert a
“0” to a “1.”
START
Write Program
Command Sequence
Unlock Bypass Command Sequence
Data Poll
from System
The unlock bypass feature allows the system to pro-
gram words to the device faster than using the stan-
dard program command sequence. The unlock
bypass command sequence is initiated by first writing
two unlock cycles. This is followed by a third write
cycle containing the unlock bypass command, 20h.
The device then enters the unlock bypass mode. A
two-cycle unlock bypass program command sequence
is all that is required to program in this mode. The first
cycle in this sequence contains the unlock bypass pro-
gram command, A0h; the second cycle contains the
program address and data. Additional data is pro-
grammed in the same manner. This mode dispenses
with the initial two unlock cycles required in the stan-
dard program command sequence, resulting in faster
total programming time. Table 10 shows the require-
ments for the command sequence.
Embedded
Program
algorithm
in progress
Verify Data?
No
Yes
No
Increment Address
Last Address?
Yes
Programming
Completed
Note: See Table 10 for program command sequence.
During the unlock bypass mode, only the Unlock By-
pass Program and Unlock Bypass Reset commands
are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset com-
mand sequence. The first cycle must contain the data
90h. The second cycle must contain the data 00h. The
device then returns to the read mode.
Figure 3. Program Operation
Chip Erase Command Sequence
The device offers accelerated program operations
through the ACC pin. When the system asserts VHH on
the ACC pin, the device automatically enters the Un-
lock Bypass mode. The system may then write the
two-cycle Unlock Bypass program command se-
quence. The device uses the higher voltage on the
ACC pin to accelerate the operation. Note that the
ACC pin must not be at VHH for operations other than
accelerated programming, or device damage may re-
sult.
Chip erase is a six bus cycle operation. The chip erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase
algorithm. The device does not require the system to
preprogram prior to erase. The Embedded Erase algo-
rithm automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical
erase. The system is not required to provide any con-
trols or timings during these operations. Table 10
shows the address and data requirements for the chip
erase command sequence.
Figure 3 illustrates the algorithm for the program oper-
ation. Refer to the Erase and Program Operations
26
Am29LV640D/Am29LV641D
September 20, 2002
When the Embedded Erase algorithm is complete, the
device returns to the read mode and addresses are no
longer latched. The system can determine the status
of the erase operation by using DQ7, DQ6, DQ2, or
RY/BY#. Refer to the Write Operation Status section
for information on these status bits.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses
are no longer latched. The system can determine the
status of the erase operation by reading DQ7, DQ6,
DQ2, or RY/BY#. Note that while the Embedded Erase
operation is in progress, the system can read data
from the non-erasing sector. Refer to the Write Opera-
tion Status section for information on these status bits.
Any commands written during the chip erase operation
are ignored. However, note that a hardware reset im-
mediately terminates the erase operation. If that oc-
curs, the chip erase command sequence should be
reinitiated once the device has returned to reading
array data, to ensure data integrity.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other com-
mands are ignored. However, note that a hardware
reset immediately terminates the erase operation. If
that occurs, the sector erase command sequence
should be reinitiated once the device has returned to
reading array data, to ensure data integrity.
Figure 4 illustrates the algorithm for the erase opera-
tion. Refer to the Erase and Program Operations ta-
bles in the AC Characteristics section for parameters,
and Figure 17 section for timing diagrams.
Figure 4 illustrates the algorithm for the erase opera-
tion. Refer to the Erase and Program Operations ta-
bles in the AC Characteristics section for parameters,
and Figure 17 section for timing diagrams.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector
erase command sequence is initiated by writing two
unlock cycles, followed by a set-up command. Two ad-
ditional unlock cycles are written, and are then fol-
lowed by the address of the sector to be erased, and
the sector erase command. Table 10 shows the ad-
dress and data requirements for the sector erase com-
mand sequence.
Erase Suspend/Erase Resume
Commands
The Erase Suspend command, B0h, allows the sys-
tem to interrupt a sector erase operation and then read
data from, or program data to, any sector not selected
for erasure. This command is valid only during the
sector erase operation, including the 50 µs time-out
period during the sector erase command sequence.
The Erase Suspend command is ignored if written dur-
ing the chip erase operation or Embedded Program
algorithm.
The device does not require the system to preprogram
prior to erase. The Embedded Erase algorithm auto-
matically programs and verifies the entire memory for
an all zero data pattern prior to electrical erase. The
system is not required to provide any controls or tim-
ings during these operations.
When the Erase Suspend command is written during
the sector erase operation, the device requires a max-
imum of 20 µs to suspend the erase operation. How-
ever, when the Erase Suspend command is written
during the sector erase time-out, the device immedi-
ately terminates the time-out period and suspends the
erase operation.
After the command sequence is written, a sector erase
time-out of 50 µs occurs. During the time-out period,
additional sector addresses and sector erase com-
mands may be written. Loading the sector erase buffer
may be done in any sequence, and the number of sec-
tors may be from one sector to all sectors. The time
between these additional cycles must be less than 50
µs, otherwise erasure may begin. Any sector erase
address and command following the exceeded
time-out may or may not be accepted. It is recom-
mended that processor interrupts be disabled during
this time to ensure all commands are accepted. The
interrupts can be re-enabled after the last Sector
Erase command is written. Any command other than
Sector Erase or Erase Suspend during the
time-out period resets the device to the read
mode. The system must rewrite the command se-
quence and any additional addresses and commands.
After the erase operation has been suspended, the
device enters the erase-suspend-read mode. The sys-
tem can read data from or program data to any sector
not selected for erasure. (The device “erase sus-
pends” all sectors selected for erasure.) Reading at
any address within erase-suspended sectors pro-
duces status information on DQ7–DQ0. The system
can use DQ7, or DQ6 and DQ2 together, to determine
if a sector is actively erasing or is erase-suspended.
Refer to the Write Operation Status section for infor-
mation on these status bits.
After an erase-suspended program operation is com-
plete, the device returns to the erase-suspend-read
mode. The system can determine the status of the
program operation using the DQ7 or DQ6 status bits,
just as in the standard word program operation.
The system can monitor DQ3 to determine if the sec-
tor erase timer has timed out (See the section on DQ3:
Sector Erase Timer.). The time-out begins from the ris-
ing edge of the final WE# pulse in the command
sequence.
September 20, 2002
Am29LV640D/Am29LV641D
27
Refer to the Write Operation Status section for more
information.
In the erase-suspend-read mode, the system can also
issue the autoselect command sequence. Refer to the
Autoselect Mode and Autoselect Command Sequence
sections for details.
START
Write Erase
Command Sequence
(Notes 1, 2)
To resume the sector erase operation, the system
must write the Erase Resume command. The address
of the erase-suspended sector is required when writ-
ing this command. Further writes of the Resume com-
mand are ignored. Another Erase Suspend command
can be written after the chip has resumed erasing.
Data Poll to Erasing
Bank from System
Embedded
Erase
algorithm
in progress
No
Data = FFh?
Yes
Erasure Completed
Notes:
1. See Table 10 for erase command sequence.
2. See the section on DQ3 for information on the sector
erase timer.
Figure 4. Erase Operation
28
Am29LV640D/Am29LV641D
September 20, 2002
Command Definitions
Table 10. Command Definitions
Bus Cycles (Notes 1–4)
Third Fourth
Addr
First
Second
Fifth
Sixth
Command
Sequence
Addr Data Addr Data
Data
Addr
Data
Addr Data Addr Data
Read (Note 5)
Reset (Note 6)
Manufacturer ID
Device ID
1
1
4
4
RA
XXX
555
555
RD
F0
AA
AA
2AA
2AA
55
55
555
555
90
90
X00
X01
0001
22D7
SecSi Sector Factory
Protect (Note 8)
(see
Note 8)
4
4
555
555
AA
AA
2AA
2AA
55
55
555
555
90
X03
Sector Group Protect Verify
(Note 9)
XX00/
XX01
90 (SA)X02
88
Enter SecSi Sector Region
Exit SecSi Sector Region
Program
3
4
4
3
555
555
555
555
AA
AA
AA
AA
2AA
2AA
2AA
2AA
55
55
55
55
555
555
555
555
90
A0
20
XXX
PA
00
PD
Unlock Bypass
Unlock Bypass Program (Note 10)
2
XXX
A0
PA
PD
Unlock Bypass Reset (Note 11)
Chip Erase
2
6
6
1
1
1
XXX
555
555
BA
90
AA
AA
B0
30
XXX
2AA
2AA
00
55
55
555
555
80
80
555
555
AA
AA
2AA
2AA
55
55
555
SA
10
30
Sector Erase
Erase Suspend (Note 12)
Erase Resume (Note 13)
CFI Query (Note 14)
BA
55
98
Legend:
X = Don’t care
PD = Data to be programmed at location PA. Data latches on the rising
edge of WE# or CE# pulse, whichever happens first.
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A21–A15 uniquely select any sector.
latch on the falling edge of the WE# or CE# pulse, whichever happens
later.
Notes:
1. See Table 1 for description of bus operations.
8. If WP# protects the highest address sector (or if WP# is not
available), the data is 98h for factory locked and 18h for not
factory locked. If WP# protects the lowest address sector, the
data is 88h for factory locked and 08h for not factor locked.
2. All values are in hexadecimal.
3. Except for the read cycle and the fourth cycle of the autoselect
command sequence, all bus cycles are write cycles.
9. The data is 00h for an unprotected sector group and 01h for a
protected sector group.
4. During unlock cycles, (when lower address bits are 555 or 2AAh
as shown in table) address bits higher than A11 (except where BA
is required) and data bits higher than DQ7 are don’t cares.
10. The Unlock Bypass command is required prior to the Unlock
Bypass Program command.
5. No unlock or command cycles required when device is in read
mode.
11. The Unlock Bypass Reset command is required to return to the
read mode when the device is in the unlock bypass mode.
6. The Reset command is required to return to the read mode (or to
the erase-suspend-read mode if previously in Erase Suspend)
when the device is in the autoselect mode, or if DQ5 goes high
(while the device is providing status information).
12. The system may read and program in non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase
operation.
7. The fourth cycle of the autoselect command sequence is a read
cycle. Data bits DQ15–DQ8 are don’t care. See the Autoselect
Command Sequence section for more information.
13. The Erase Resume command is valid only during the Erase
Suspend mode.
14. Command is valid when device is ready to read array data or when
device is in autoselect mode.
September 20, 2002
Am29LV640D/Am29LV641D
29
WRITE OPERATION STATUS
The device provides several bits to determine the status of
a program or erase operation: DQ2, DQ3, DQ5, DQ6, and
DQ7. Table 11 and the following subsections describe the
function of these bits. DQ7 and DQ6 each offer a method
for determining whether a program or erase operation is
complete or in progress. The device also provides a hard-
ware-based output signal, RY/BY#, to determine whether
an Embedded Program or Erase operation is in progress or
has been completed.
invalid. Valid data on DQ0–DQ7 will appear on suc-
cessive read cycles.
Table 11 shows the outputs for Data# Polling on DQ7.
Figure 5 shows the Data# Polling algorithm. Figure 18
in the AC Characteristics section shows the Data#
Polling timing diagram.
START
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system
whether an Embedded Program or Erase algorithm is in
progress or completed, or whether the device is in Erase
Suspend. Data# Polling is valid after the rising edge of the
final WE# pulse in the command sequence.
Read DQ7–DQ0
Addr = VA
During the Embedded Program algorithm, the device out-
puts on DQ7 the complement of the datum programmed to
DQ7. This DQ7 status also applies to programming during
Erase Suspend. When the Embedded Program algorithm is
complete, the device outputs the datum programmed to
DQ7. The system must provide the program address to
read valid status information on DQ7. If a program address
falls within a protected sector, Data# Polling on DQ7 is ac-
tive for approximately 1 µs, then the device returns to the
read mode.
Yes
DQ7 = Data?
No
No
DQ5 = 1?
Yes
During the Embedded Erase algorithm, Data# Polling
produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the device enters the Erase
Suspend mode, Data# Polling produces a “1” on DQ7.
The system must provide an address within any of the
sectors selected for erasure to read valid status infor-
mation on DQ7.
Read DQ7–DQ0
Addr = VA
Yes
DQ7 = Data?
After an erase command sequence is written, if all
sectors selected for erasing are protected, Data# Poll-
ing on DQ7 is active for approximately 100 µs, then
the device returns to the read mode. If not all selected
sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the se-
lected sectors that are protected. However, if the sys-
tem reads DQ7 at an address within a protected
sector, the status may not be valid.
No
PASS
FAIL
Notes:
1. VA = Valid address for programming. During a sector
erase operation, a valid address is any sector address
within the sector being erased. During chip erase, a
valid address is any non-protected sector address.
Just prior to the completion of an Embedded Program
or Erase operation, DQ7 may change asynchronously
with DQ0–DQ6 while Output Enable (OE#) is asserted
low. That is, the device may change from providing
status information to valid data on DQ7. Depending on
when the system samples the DQ7 output, it may read
the status or valid data. Even if the device has com-
pleted the program or erase operation and DQ7 has
valid data, the data outputs on DQ0–DQ6 may be still
2. DQ7 should be rechecked even if DQ5 = “1” because
DQ7 may change simultaneously with DQ5.
Figure 5. Data# Polling Algorithm
30
Am29LV640D/Am29LV641D
September 20, 2002
Table 11 shows the outputs for Toggle Bit I on DQ6.
Figure 6 shows the toggle bit algorithm. Figure 19 in
the “AC Characteristics” section shows the toggle bit
timing diagrams. Figure 20 shows the differences be-
tween DQ2 and DQ6 in graphical form. See also the
subsection on DQ2: Toggle Bit II.
RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin
which indicates whether an Embedded Algorithm is in
progress or complete. The RY/BY# status is valid after
the rising edge of the final WE# pulse in the command
sequence. Since RY/BY# is an open-drain output, sev-
eral RY/BY# pins can be tied together in parallel with a
pull-up resistor to VCC
.
If the output is low (Busy), the device is actively eras-
ing or programming. (This includes programming in
the Erase Suspend mode.) If the output is high
(Ready), the device is in the read mode, the standby
mode, or the device is in the erase-suspend-read
mode.
START
Read DQ7–DQ0
Table 11 shows the outputs for RY/BY#.
Read DQ7–DQ0
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or com-
plete, or whether the device has entered the Erase
Suspend mode. Toggle Bit I may be read at any ad-
dress, and is valid after the rising edge of the final
WE# pulse in the command sequence (prior to the
program or erase operation), and during the sector
erase time-out.
No
Toggle Bit
= Toggle?
Yes
No
During an Embedded Program or Erase algorithm op-
eration, successive read cycles to any address cause
DQ6 to toggle. The system may use either OE# or
CE# to control the read cycles. When the operation is
complete, DQ6 stops toggling.
DQ5 = 1?
Yes
Read DQ7–DQ0
After an erase command sequence is written, if all sectors
selected for erasing are protected, DQ6 toggles for approxi-
mately 100 µs, then returns to reading array data. If not all
selected sectors are protected, the Embedded Erase algo-
rithm erases the unprotected sectors, and ignores the se-
lected sectors that are protected.
Twice
Toggle Bit
= Toggle?
No
The system can use DQ6 and DQ2 together to determine
whether a sector is actively erasing or is erase-suspended.
When the device is actively erasing (that is, the Embedded
Erase algorithm is in progress), DQ6 toggles. When the de-
vice enters the Erase Suspend mode, DQ6 stops toggling.
However, the system must also use DQ2 to determine
which sectors are erasing or erase-suspended. Alterna-
tively, the system can use DQ7 (see the subsection on
DQ7: Data# Polling).
Yes
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Note: The system should recheck the toggle bit even if
DQ5 = “1” because the toggle bit may stop toggling as DQ5
changes to “1.” See the subsections on DQ6 and DQ2 for
more information.
If a program address falls within a protected sector,
DQ6 toggles for approximately 1 µs after the program
command sequence is written, then returns to reading
array data.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded Pro-
gram algorithm is complete.
Figure 6. Toggle Bit Algorithm
September 20, 2002
Am29LV640D/Am29LV641D
31
the toggle bit and DQ5 through successive read cy-
cles, determining the status as described in the previ-
ous paragraph. Alternatively, it may choose to perform
other system tasks. In this case, the system must start
at the beginning of the algorithm when it returns to de-
termine the status of the operation (top of Figure 6).
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indi-
cates whether a particular sector is actively erasing
(that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit
II is valid after the rising edge of the final WE# pulse in
the command sequence.
DQ5: Exceeded Timing Limits
DQ2 toggles when the system reads at addresses
within those sectors that have been selected for era-
sure. (The system may use either OE# or CE# to con-
trol the read cycles.) But DQ2 cannot distinguish
whether the sector is actively erasing or is erase-sus-
pended. DQ6, by comparison, indicates whether the
device is actively erasing, or is in Erase Suspend, but
cannot distinguish which sectors are selected for era-
sure. Thus, both status bits are required for sector and
mode information. Refer to Table 11 to compare out-
puts for DQ2 and DQ6.
DQ5 indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under these
conditions DQ5 produces a “1,” indicating that the program
or erase cycle was not successfully completed.
The device may output a “1” on DQ5 if the system tries
to program a “1” to a location that was previously pro-
grammed to “0.” Only an erase operation can
change a “0” back to a “1.” Under this condition, the
device halts the operation, and when the timing limit
has been exceeded, DQ5 produces a “1.”
Under both these conditions, the system must write
the reset command to return to the read mode (or to
the erase-suspend-read mode if the device was previ-
ously in the erase-suspend-program mode).
Figure 6 shows the toggle bit algorithm in flowchart
form, and the section “DQ2: Toggle Bit II” explains the
algorithm. See also the DQ6: Toggle Bit I subsection.
Figure 19 shows the toggle bit timing diagram. Figure
20 shows the differences between DQ2 and DQ6 in
graphical form.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not
erasure has begun. (The sector erase timer does not
apply to the chip erase command.) If additional
sectors are selected for erasure, the entire time-out
also applies after each additional sector erase com-
mand. When the time-out period is complete, DQ3
switches from a “0” to a “1.” If the time between addi-
tional sector erase commands from the system can be
assumed to be less than 50 µs, the system need not
monitor DQ3. See also the Sector Erase Command
Sequence section.
Reading Toggle Bits DQ6/DQ2
Refer to Figure 6 for the following discussion. When-
ever the system initially begins reading toggle bit sta-
tus, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically,
the system would note and store the value of the tog-
gle bit after the first read. After the second read, the
system would compare the new value of the toggle bit
with the first. If the toggle bit is not toggling, the device
has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the fol-
lowing read cycle.
After the sector erase command is written, the system
should read the status of DQ7 (Data# Polling) or DQ6
(Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is
“1,” the Embedded Erase algorithm has begun; all fur-
ther commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the
device will accept additional sector erase commands.
To ensure the command has been accepted, the sys-
tem software should check the status of DQ3 prior to
and following each subsequent sector erase com-
mand. If DQ3 is high on the second status check, the
last command might not have been accepted.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the sys-
tem also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should
then determine again whether the toggle bit is tog-
gling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer
toggling, the device has successfully completed the
program or erase operation. If it is still toggling, the de-
vice did not completed the operation successfully, and
the system must write the reset command to return to
reading array data.
Table 11 shows the status of DQ3 relative to the other
status bits.
The remaining scenario is that the system initially de-
termines that the toggle bit is toggling and DQ5 has
not gone high. The system may continue to monitor
32
Am29LV640D/Am29LV641D
September 20, 2002
Table 11. Write Operation Status
DQ7
(Note 2)
DQ5
(Note 1)
DQ2
(Note 2)
RY/BY#
(Note 3)
Status
DQ6
DQ3
N/A
1
Embedded Program Algorithm
Embedded Erase Algorithm
Erase
DQ7#
0
Toggle
Toggle
0
0
No toggle
Toggle
0
0
Standard
Mode
1
No toggle
0
N/A
Toggle
1
Suspended Sector
Erase-Suspend-
Read
Erase
Suspend
Mode
Non-Erase
Data
Data
Data
0
Data
N/A
Data
N/A
1
0
Suspended Sector
Erase-Suspend-Program
DQ7#
Toggle
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.
Refer to the section on DQ5 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
3. RY/BY# is only available on the FBGA package.
September 20, 2002
Am29LV640D/Am29LV641D
33
ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . . . –65°C to +150°C
20 ns
20 ns
+0.8 V
Ambient Temperature
with Power Applied . . . . . . . . . . . . . –65°C to +125°C
–0.5 V
–2.0 V
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . .–0.5 V to +4.0 V
VIO. . . . . . . . . . . . . . . . . . . . . . . . .–0.5 V to +5.5 V
20 ns
A9, OE#, ACC, and RESET#
(Note 2). . . . . . . . . . . . . . . . . . . .–0.5 V to +12.5 V
Figure 7. Maximum Negative
Overshoot Waveform
All other pins (Note 1) . . . . . . –0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is –0.5 V.
During voltage transitions, input or I/O pins may
overshoot VSS to –2.0 V for periods of up to 20 ns.
Maximum DC voltage on input or I/O pins is VCC +0.5 V.
See Figure 7. During voltage transitions, input or I/O pins
may overshoot to VCC +2.0 V for periods up to 20 ns. See
Figure 8.
20 ns
VCC
+2.0 V
VCC
+0.5 V
2. Minimum DC input voltage on pins A9, OE#, ACC, and
RESET# is –0.5 V. During voltage transitions, A9, OE#,
ACC, and RESET# may overshoot VSS to –2.0 V for
periods of up to 20 ns. See Figure 7. Maximum DC input
voltage on pin A9, OE#, ACC, and RESET# is +12.5 V
which may overshoot to +14.0 V for periods up to 20 ns.
2.0 V
20 ns
20 ns
Figure 8. Maximum Positive
Overshoot Waveform
3. No more than one output may be shorted to ground at a
time. Duration of the short circuit should not be greater
than one second.
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This
is a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating
conditions for extended periods may affect device reliability.
OPERATING RANGES
Industrial (I) Devices
Ambient Temperature (TA) . . . . . . . . . –40°C to +85°C
Extended (E) Devices
Ambient Temperature (TA) . . . . . . . . –55°C to +125°C
Supply Voltages
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0–3.6 V
VIO . . . . . . . . . . . . . . . . .either 1.8–2.9 V or 3.0–5.0 V
(see Ordering Information section)
Operating ranges define those limits between which the
functionality of the device is guaranteed.
34
Am29LV640D/Am29LV641D
September 20, 2002
DC CHARACTERISTICS
CMOS Compatible
Parameter
Symbol
Parameter Description
Test Conditions
VIN = VSS to VCC
VCC = VCC max
VCC = VCC max; A9 = 12.5 V
Min
Typ
Max
±1.0
35
Unit
µA
,
ILI
Input Load Current (Note 1)
A9, ACC Input Load Current
Output Leakage Current
ILIT
µA
VOUT = VSS to VCC
VCC = VCC max
,
ILO
±1.0
µA
5 MHz
1 MHz
9
2
16
4
VCC Active Read Current
(Notes 2, 3)
ICC1
CE# = VIL, OE# = VIH
mA
ICC2
ICC3
ICC4
ICC5
VCC Active Write Current (Notes 3, 4) CE# = VIL, OE# = VIH, WE# = VIL
26
30
mA
µA
µA
µA
CE#, RESET# = VCC ± 0.3 V,
VCC Standby Current (Note 3)
WP# = VIH
0.2
0.2
0.2
5
5
5
VCC Reset Current (Note 3)
RESET# = VSS ± 0.3 V, WP# = VIH
VIH = VCC ± 0.3 V;
VIL = VSS ± 0.3 V, WP# = VIH
Automatic Sleep Mode (Notes 3, 5)
ACC pin
5
10
30
mA
mA
V
IACC
ACC Accelerated Program Current
CE# = VIL, OE# = VIH
V
CC pin
15
VIL
VIH
Input Low Voltage (Note 6)
Input High Voltage (Note 6)
–0.5
0.8
0.7 x VCC
VCC + 0.3
V
Voltage for ACC Program
Acceleration
VHH
VID
VCC = 3.0 V ± 10%
11.5
8.5
12.5
V
V
Voltage for Autoselect and
Temporary Sector Unprotect
VCC = 3.0 V ± 10%
12.5
0.45
VOL
VOH1
VOH2
VLKO
Output Low Voltage
IOL = 4.0 mA, VCC = VCC min
V
V
V
V
IOH = –2.0 mA, VCC = VCC min
IOH = –100 µA, VCC = VCC min
0.8 VIO
VIO–0.4
2.3
Output High Voltage
Low VCC Lock-Out Voltage (Note 7)
2.5
Notes:
1. On the WP# pin only, the maximum input load current when WP# = VIL is ± 5.0 µA.
2. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH.
3. Maximum ICC specifications are tested with VCC = VCCmax.
4. ICC active while Embedded Erase or Embedded Program is in progress.
5. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. Typical sleep mode current is
200 nA.
6. If VIO < VCC, maximum VIL for CE# and DQ I/Os is 0.3 VIO. If VIO < VCC, minimum VIH for CE# and DQ I/Os is 0.7 VIO. Maximum VIH
for these connections is VIO + 0.3 V
7. Not 100% tested.
September 20, 2002
Am29LV640D/Am29LV641D
35
DC CHARACTERISTICS
Zero-Power Flash
25
20
15
10
5
0
0
500
1000
1500
2000
2500
3000
3500
4000
Time in ns
Note: Addresses are switching at 1 MHz
Figure 9. ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents)
12
10
8
3.6 V
3.0 V
6
4
2
0
1
2
3
4
5
Frequency in MHz
Note: T = 25 °C
Figure 10. Typical ICC1 vs. Frequency
Am29LV640D/Am29LV641D
36
September 20, 2002
TEST CONDITIONS
Table 12. Test Specifications
3.3 V
90R,
120R,
Test Condition
Output Load
101R
121R
Unit
2.7 kΩ
1 TTL gate
Device
Under
Test
Output Load Capacitance, CL
(including jig capacitance)
30
100
pF
C
L
6.2 kΩ
Input Rise and Fall Times
Input Pulse Levels
5
0.0–3.0
ns
V
Input timing measurement
reference levels (See Note)
1.5
V
V
Note: Diodes are IN3064 or equivalent
Output timing measurement
reference levels
0.5 VIO
Figure 11. Test Setup
Note: If VIO < VCC, the reference level is 0.5 VIO.
KEY TO SWITCHING WAVEFORMS
WAVEFORM
INPUTS
OUTPUTS
Steady
Changing from H to L
Changing from L to H
Changing, State Unknown
Don’t Care, Any Change Permitted
Does Not Apply
Center Line is High Impedance State (High Z)
3.0 V
1.5 V
0.5 VIO V
Input
Measurement Level
Output
0.0 V
Note: If VIO < VCC, the input measurement reference level is 0.5 VIO.
Figure 12. Input Waveforms and
Measurement Levels
September 20, 2002
Am29LV640D/Am29LV641D
37
AC CHARACTERISTICS
Read-Only Operations
Parameter
Speed Options
120R,
JEDEC
tAVAV
Std.
tRC
Description
Test Setup
90R
90
90
90
35
30
30
101R
100
100
100
35
121R
120
120
120
50
Unit
ns
Read Cycle Time (Note 1)
Min
CE#, OE# = VIL Max
tAVQV
tELQV
tGLQV
tEHQZ
tGHQZ
tACC
tCE
tOE
tDF
Address to Output Delay
ns
Chip Enable to Output Delay
Output Enable to Output Delay
Chip Enable to Output High Z (Note 1)
Output Enable to Output High Z (Note 1)
OE# = VIL
Max
Max
Max
Max
ns
ns
30
30
ns
tDF
30
30
ns
Output Hold Time From Addresses, CE# or
OE#, Whichever Occurs First
tAXQX
tOH
Min
Min
Min
0
0
ns
ns
ns
Read
Output Enable Hold
tOEH
Toggle and
Data# Polling
Time (Note 1)
10
Notes:
1. Not 100% tested.
2. See Figure 11 and Table 12 for test specifications.
tRC
Addresses Stable
tACC
Addresses
CE#
tRH
tRH
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
Output Valid
HIGH Z
HIGH Z
Outputs
RESET#
RY/BY#
0 V
Figure 13. Read Operation Timings
38
Am29LV640D/Am29LV641D
September 20, 2002
AC CHARACTERISTICS
Hardware Reset (RESET#)
Parameter
JEDEC
Std
Description
All Speed Options
Unit
RESET# Pin Low (During Embedded Algorithms)
to Read Mode (See Note)
tReady
Max
Max
20
µs
RESET# Pin Low (NOT During Embedded
Algorithms) to Read Mode (See Note)
tReady
500
ns
tRP
tRH
tRPD
tRB
RESET# Pulse Width
Min
Min
Min
Min
500
50
20
0
ns
ns
µs
ns
Reset High Time Before Read (See Note)
RESET# Low to Standby Mode
RY/BY# Recovery Time
Note: Not 100% tested.
RY/BY#
CE#, OE#
RESET#
tRH
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
RY/BY#
tRB
CE#, OE#
RESET#
tRP
Figure 14. Reset Timings
September 20, 2002
Am29LV640D/Am29LV641D
39
AC CHARACTERISTICS
Erase and Program Operations
Parameter
Speed Options
120R,
JEDEC
tAVAV
Std.
tWC
tAS
Description
90R
101R
100
0
121R
Unit
ns
Write Cycle Time (Note 1)
Address Setup Time
Min
Min
90
120
tAVWL
ns
Address Setup Time to OE# low during toggle bit
polling
tASO
tAH
Min
Min
Min
15
45
0
ns
ns
ns
tWLAX
Address Hold Time
45
45
50
50
Address Hold Time From CE# or OE# high
during toggle bit polling
tAHT
tDVWH
tWHDX
tDS
tDH
Data Setup Time
Min
Min
Min
45
0
ns
ns
ns
Data Hold Time
tOEPH
Output Enable High during toggle bit polling
20
Read Recovery Time Before Write
(OE# High to WE# Low)
tGHWL
tGHWL
Min
0
ns
tELWL
tWHEH
tCS
tCH
CE# Setup Time
Min
Min
Min
Min
Typ
Typ
Typ
Min
Min
Min
Min
0
0
ns
ns
ns
ns
µs
µs
sec
ns
µs
ns
ns
CE# Hold Time
tWLWH
tWP
Write Pulse Width
Write Pulse Width High
35
35
30
11
7
50
tWHDL
tWPH
tWHWH1
tWHWH1
tWHWH2
tWHWH1 Word Programming Operation (Note 2)
tWHWH1 Accelerated Word Programming Operation (Note 2)
tWHWH2 Sector Erase Operation (Note 2)
0.9
250
50
0
tVHH
tVCS
tRB
VHH Rise and Fall Time (Note 1)
VCC Setup Time (Note 1)
Write Recovery Time from RY/BY#
Program/Erase Valid to RY/BY# Delay
tBUSY
90
Notes:
1. Not 100% tested.
2. See the “Erase And Programming Performance” section for more information.
40
Am29LV640D/Am29LV641D
September 20, 2002
AC CHARACTERISTICS
Program Command Sequence (last two cycles)
Read Status Data (last two cycles)
tAS
PA
tWC
Addresses
555h
PA
PA
tAH
CE#
OE#
tCH
tWHWH1
tWP
WE#
Data
tWPH
tCS
tDS
tDH
PD
DOUT
A0h
Status
tBUSY
tRB
RY/BY#
VCC
tVCS
otes:
. PA = program address, PD = program data, DOUT is the true data at the program address.
. Illustration shows device in word mode.
Figure 15. Program Operation Timings
VHH
VIL or VIH
VIL or VIH
ACC
tVHH
tVHH
Figure 16. Accelerated Program Timing Diagram
September 20, 2002
Am29LV640D/Am29LV641D
41
AC CHARACTERISTICS
Erase Command Sequence (last two cycles)
Read Status Data
VA
tAS
SA
tWC
VA
Addresses
CE#
2AAh
555h for chip erase
tAH
tCH
OE#
tWP
WE#
tWPH
tWHWH2
tCS
tDS
tDH
In
Data
Complete
55h
30h
Progress
10 for Chip Erase
tBUSY
tRB
RY/BY#
VCC
tVCS
Notes:
1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”.
2. These waveforms are for the word mode.
Figure 17. Chip/Sector Erase Operation Timings
42
Am29LV640D/Am29LV641D
September 20, 2002
AC CHARACTERISTICS
tRC
VA
Addresses
VA
VA
tACC
tCE
CE#
tCH
tOE
OE#
WE#
tOEH
tDF
tOH
High Z
High Z
DQ7
Valid Data
Complement
Complement
True
DQ0–DQ6
Valid Data
Status Data
True
Status Data
tBUSY
RY/BY#
Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data
read cycle.
Figure 18. Data# Polling Timings
(During Embedded Algorithms)
September 20, 2002
Am29LV640D/Am29LV641D
43
AC CHARACTERISTICS
tAHT
tAS
Addresses
tAHT
tASO
CE#
tOEH
WE#
tCEPH
tOEPH
OE#
tDH
Valid Data
tOE
Valid
Status
Valid
Status
Valid
Status
DQ6/DQ2
Valid Data
(first read)
(second read)
(stops toggling)
RY/BY#
Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status
read cycle, and array data read cycle
Figure 19. Toggle Bit Timings
(During Embedded Algorithms)
Enter
Embedded
Erasing
Erase
Suspend
Enter Erase
Suspend Program
Erase
Resume
Erase
Erase Suspend
Read
Erase
Suspend
Program
Erase
Complete
WE#
Erase
Erase Suspend
Read
DQ6
DQ2
Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle
DQ2 and DQ6.
Figure 20. DQ2 vs. DQ6
44
Am29LV640D/Am29LV641D
September 20, 2002
AC CHARACTERISTICS
Temporary Sector Unprotect
Parameter
JEDEC
Std
Description
All Speed Options
Unit
tVIDR
VID Rise and Fall Time (See Note)
Min
Min
500
ns
RESET# Setup Time for Temporary Sector
Unprotect
tRSP
4
4
µs
µs
RESET# Hold Time from RY/BY# High for
Temporary Sector Group Unprotect
tRRB
Min
Note: Not 100% tested.
VID
VID
RESET#
VSS, VIL,
or VIH
VSS, VIL,
or VIH
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRRB
tRSP
RY/BY#
Figure 21. Temporary Sector Group Unprotect Timing Diagram
September 20, 2002
Am29LV640D/Am29LV641D
45
AC CHARACTERISTICS
V
ID
IH
V
RESET#
SA, A6,
A1, A0
Valid*
Valid*
Valid*
Status
Sector Group Protect or Unprotect
Verify
40h
Data
60h
60h
Sector Group Protect: 150 µs,
Sector Group Unprotect: 15 ms
1 µs
CE#
WE#
OE#
For sector group protect, A6 = 0, A1 = 1, A0 = 0. For sector group unprotect, A6 = 1, A1 = 1, A0 = 0.
Figure 22. Sector Group Protect and Unprotect Timing Diagram
46
Am29LV640D/Am29LV641D
September 20, 2002
AC CHARACTERISTICS
Alternate CE# Controlled Erase and Program Operations
Parameter
Speed Options
120R,
JEDEC
tAVAV
Std
tWC
tAS
Description
90R
101R
100
0
121R
Unit
ns
Write Cycle Time (Note 1)
Address Setup Time
Address Hold Time
Data Setup Time
Data Hold Time
Min
Min
Min
Min
Min
90
120
tAVWL
tELAX
tDVEH
tEHDX
ns
tAH
tDS
tDH
45
45
45
50
50
ns
45
ns
0
ns
Read Recovery Time Before Write
(OE# High to WE# Low)
tGHEL
tGHEL
Min
0
ns
tWLEL
tEHWH
tELEH
tWS
tWH
tCP
WE# Setup Time
WE# Hold Time
Min
Min
Min
Min
Typ
0
ns
ns
ns
ns
µs
0
CE# Pulse Width
CE# Pulse Width High
45
45
30
11
50
tEHEL
tCPH
tWHWH1
tWHWH1 Word Programming Operation (Note 2)
Accelerated Word Programming Operation
(Note 2)
tWHWH1
tWHWH2
Notes:
tWHWH1
Typ
Typ
7
µs
tWHWH2 Sector Erase Operation (Note 2)
0.9
sec
1. Not 100% tested.
2. See the “Erase And Programming Performance” section for more information.
September 20, 2002
Am29LV640D/Am29LV641D
47
AC CHARACTERISTICS
555 for program
PA for program
2AA for erase
SA for sector erase
555 for chip erase
Data# Polling
Addresses
PA
tWC
tWH
tAS
tAH
WE#
OE#
tGHEL
tWHWH1 or 2
tCP
CE#
Data
tWS
tCPH
tDS
tBUSY
tDH
DQ7#
DOUT
tRH
A0 for program
55 for erase
PD for program
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Notes:
1. Figure indicates last two bus cycles of a program or erase operation.
2. PA = program address, SA = sector address, PD = program data.
3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device.
4. Waveforms are for the word mode.
Figure 23. Alternate CE# Controlled Write (Erase/Program) Operation Timings
48
Am29LV640D/Am29LV641D
September 20, 2002
ERASE AND PROGRAMMING PERFORMANCE
Parameter
Typ (Note 1) Max (Note 2)
Unit
sec
sec
Comments
Sector Erase Time
Chip Erase Time
0.9
15
Excludes 00h programming
prior to erasure (Note 4)
115
Excludes system level
overhead (Note 5)
Word Program Time
11
300
µs
Accelerated Word Program Time
Chip Program Time (Note 3)
Notes:
7
210
144
µs
48
sec
1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC, 1,000,000 cycles. Additionally,
programming typicals assume checkerboard pattern.
2. Under worst case conditions of 90°C, VCC = 3.0 V, 1,000,000 cycles.
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most words
program faster than the maximum program times listed.
4. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table
10 for further information on command definitions.
6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles.
LATCHUP CHARACTERISTICS
Description
Min
Max
Input voltage with respect to VSS on all pins except I/O pins
(including A9, OE#, and RESET#)
–1.0 V
12.5 V
Input voltage with respect to VSS on all I/O pins
VCC Current
–1.0 V
VCC + 1.0 V
+100 mA
–100 mA
Note: Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time.
TSOP PIN CAPACITANCE
Parameter
Symbol
Parameter Description
Input Capacitance
Test Setup
VIN = 0
Typ
6
Max
7.5
12
Unit
pF
CIN
COUT
CIN2
Output Capacitance
Control Pin Capacitance
VOUT = 0
VIN = 0
8.5
7.5
pF
9
pF
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0 MHz.
DATA RETENTION
Parameter Description
Test Conditions
150°C
Min
10
Unit
Years
Years
Minimum Pattern Data Retention Time
125°C
20
September 20, 2002
Am29LV640D/Am29LV641D
49
PHYSICAL DIMENSIONS
SSO056—56-Pin Shrink Small Outline Package (SSOP)
Dwg rev AB; 10/99
50
Am29LV640D/Am29LV641D
September 20, 2002
PHYSICAL DIMENSIONS
FBE063—63-Ball Fine-Pitch Ball Grid Array (FBGA) 12 x 11 mm package
Dwg rev AF; 10/99
September 20, 2002
Am29LV640D/Am29LV641D
51
PHYSICAL DIMENSIONS
LAA064—64-Ball Fortified Ball Grid Array (FBGA) 13 x 11 mm package
52
Am29LV640D/Am29LV641D
September 20, 2002
PHYSICAL DIMENSIONS
TS 048—48-Pin Standard TSOP
Dwg rev AA; 10/99
Note: For reference only. BSC is an ANSI standard for Basic Space Centering.
September 20, 2002
Am29LV640D/Am29LV641D
53
PHYSICAL DIMENSIONS
TSR048—48-Pin Reverse TSOP
Dwg rev AA; 10/99
* For reference only. BSC is an ANSI standard for Basic Space Centering.
54
Am29LV640D/Am29LV641D
September 20, 2002
REVISION SUMMARY
Ordering Information
Revision A (April 26, 1999)
Added the valid combinations for the SSOP package.
Initial release.
Revision A+6 (September 28, 1999)
Revision A+1 (May 4, 1999)
Connection Diagrams
Global
Clarified which packages are available for a particular
part number.
Deleted references to the 4-word unique ESN. Re-
placed references to VCCQ with VIO.
Device Bus Operations
Connection Diagrams
VersatileIO Control: Added comment to contact AMD
for more information on this feature.
63-ball FBGA: Corrected signal for ball H7 to VIO.
Ordering Information
DC Characteristics
Added “U” designator description.
CMOS Compatible table: Added notes (1 and 2) for ILI
and test conditions column.
SecSi (Secured Silicon) Sector Flash Memory
Region
Test Conditions
In the third paragraph, replaced references to boot
sectors with SA0. Added table to show SecSi sector
contents.
In Test Specifications table and Input Waveforms and
Meaurement Levels figure, changed the output mea-
surement level to VIO/2.
DC Characteristics table
AC Characteristics
Added VIO = VCC as a test condition for ICC1 and ICC2
Changed VHH minimum specification from 8.5 V to
11.5 V.
.
Read-only Operations table: Added note for test setup
column.
Revision B (June 20, 2000)
Revision A+2 (May 14, 1999)
Global
Ordering Information
Deleted references to 150 ns speed option. Added
more information and specifications on VIO feature, in-
cluding part number distinctions. At VIO < VCC, the
available speed options are 100 ns and 120 ns. At VIO
≥ VCC, the available speed options are 90 ns and 120
ns. Changed data sheet status to “Preliminary.”
Clarified the differences between the H, L, and U
designators.
Revision A+3 (June 7, 1999)
Product Selector Guide
Added note under table.
Distinctive Characteristics
Ordering Information
Clarified on which devices RY/BY# and WP# are avail-
able. Clarified package options for devices.
Deleted the “0” from the 120 and 150 ns part numbers.
Corrected the FBGA package marking for the 150 ns
speed option.
Ordering Information
Clarified on which devices RY/BY# and WP# are avail-
able. Clarified package options for devices. Reinstated
“0” into the 120 ns speed part number for VIO = 3.0 V
to 5.0 V; added part numbers for VIO = 1.8 V to 2.9 V.
Revision A+4 (June 25, 1999)
Global
Information on the 56-pin SSOP package has been
added: pinout information and physical dimension
drawings.
Device Bus Operations table
In the legend, corrected the VHH voltage range.
SecSi Sector Contents table
Command Definitions
Corrected ending address in second row to 7Fh.
Corrected the data for SecSi Sector protection in Note
9. Added device ID data to the table.
DC Characteristics table
Redefined VOH1 and VOH2 in terms of VIO. Added note
relative to VIO for VIH and VIL. Deleted note regarding
Revision A+5 (August 2, 1999)
Block Diagram
test condition assumption of VIO = VCC
.
Separated WP# and ACC.
September 20, 2002
Am29LV640D/Am29LV641D
55
Test Conditions
where VIO ≥ VCC, and 100 and 120 ns speeds are avail-
able where VIO < VCC
.
Test Conditions table: Redefined output timing mea-
surement reference level as 0.5 VIO.
Revision B+4 (March 8, 2001)
Added note to table and figure.
Table 4, Sector Group Protection/Unprotection
Address Table
Erase and Program Opeations table, Alternate CE#
Controlled Erase and Program Operations table,
Erase and Programming Performance table
Corrected the sector group address bits for sectors
64–127.
Changed the typical sector erase time to 1.6 s.
Revision B+5 (October 11, 2001)
AC Characteristics—Figure 15. Program
Operations Timing and Figure 17. Chip/Sector
Erase Operations
Connection Diagrams, Ordering Information,
Physical Dimensions
Deleted tGHWL and changed OE# waveform to start at
high.
Added 64-ball Fortified BGA package information.
Revision B+6 (January 10, 2002)
Physical Dimensions
Global
Replaced figures with more detailed illustrations.
Clarified description of VersatileIO (VIO) in the follow-
ing sections: Distinctive Characteristics; General De-
scription; VersatileIO (VIO) Control; Operating Ranges;
DC Characteristics; CMOS compatible.
Revision B+1 (August 4, 2000)
Global
Added trademarks for SecSi Sector.
Reduced typical sector erase time from 1.6 s to 0.9 s.
Accelerated Program Operation (page 12), Unlock
Bypass Command Sequence (page 26)
DC Characteristics
Changed minimum VOH1 from 0.85VIO to 0.8VIO. De-
Added caution note regarding ACC pin.
leted reference to Note 6 for both VOH1 and VOH2
.
Absolute Maximum Ratings
Erase and Program Performance table
Corrected the maximum voltage on VIO to +5.5V.
Reduced typical sector erase time from 1.6 s to 0.9 s.
Changed typical chip program time from 90 s to 115 s.
DC Characteristics table
Added WP# = VIH to test conditions for standby cur-
Revision B+7 (April 15, 2002)
rents ICC3, ICC4, ICC5
.
Ordering Information
Revision B+2 (October 18, 2000)
Added N designator for Fortified BGA package mark-
ings.
Distinctive Characteristics
Corrected package options for 56-pin SSOP as being
available on Am29LV640DH/DL only.
Common Flash Interface (CFI)
Revised data value at address 44h. Clarified descrip-
tion of data for addresses 45–47h, 49, 4A, 4D–4Fh.
Revision B+3 (January 18, 2001)
Table 10, Command Definitions
Global
Clarified and combined Notes 4 and 5 into Note 4.
Deleted “Preliminary” status from document.
General Description
Revision B+8 (September 20, 2002)
In the second paragraph, corrected references to VIO
voltage ranges. The 90 and 120 speeds are available
Sector Erase Command Sequence
Changed sentence arrangement in fourth paragraph.
Trademarks
Copyright © 2002 Advanced Micro Devices, Inc. All rights reserved.
AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc.
ExpressFlash is a trademark of Advanced Micro Devices, Inc.
Product names used in this publication are for identification purposes only and may be trademarks of their respective companies.
56
Am29LV640D/Am29LV641D
September 20, 2002
相关型号:
AM29LV641DL90RWHIN
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DL90RZE
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DL90RZEN
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DL90RZI
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DL90RZIN
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DU101REE
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DU101REEN
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DU101REI
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DU101REIN
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DU101RFE
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DU101RFEN
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
AM29LV641DU101RFI
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI Control
AMD
©2020 ICPDF网 联系我们和版权申明