AMLB-Z_13 [AIMTEC]
Up to 700mA | Step Up LED Driver; 高达700mA |进阶LED驱动器
| 型号： | AMLB-Z_13 |
| 厂家： | 
AIMTEC |
| 描述： | Up to 700mA | Step Up LED Driver |
| 文件： | 总7页 (文件大小：418K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Series AMLB-Z
Up to 700mA | Step Up LED Driver
FEATURES:
• Step UP DC/DC LED driver
• Constant current output
• High efficiency up to 94%
• Soft Start
•
Operating Temperature -40ºC to +85ºC
Open and Short circuit LED Protection
2”x1” case package
•
•
•
Drives LED strings of up to 48V
• PWM/Digital & Analog Voltage dimming
Models
Single output
Maximum
Output Voltage (V)
Rated
Input Voltage
Max Capacitive Efficiency Ripple & Noise
Model
Vo-Vin≥5V
(V)
load (µF)
(%)
(mV p-p)
Current (mA)
AMLB-3615Z
AMLB-3625Z
AMLB-3630Z
AMLB-3635Z
9-36
9-36
9-36
9-36
14-48
14-48
14-48
14-48
150
250
300
350
100
100
100
100
90
92
92
92
350
450
450
600
14-45 (Vin:9V-18V)
23-48 (Vin: 18V-36V)
14-38 (Vin:9V-18V)
23-48 (Vin: 18V-36V)
14-32 (Vin:9V-18V)
23-48 (Vin: 18V-36V
AMLB-3650Z
AMLB-3660Z
AMLB-3670Z
9-36
9-36
9-36
500
600
700
47
47
47
93
93
94
650
650
700
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load
unless otherwise specified.
Input Specifications
Parameters
Nominal
Typical
Maximum
Units
Voltage range
9-36
VDC
Filter
Capacitor
Absolute Maximum Rating
Peak Input Voltage time
DC/DC ON (Leave open if not used)
DC/DC OFF
38
100
VDC
ms
ON –Open
OFF(shutdown) – 0V
Remote pin drive current
<1.5
1.3
8
µA
VON/OFF ≤ 3V
(Vin : 9V-32V)
(Vin : 32V-36V)
Quiescent Input Current in Shutdown
mode
mA
Analog and PWM Dimming
Control(Leave open if unused) (DIM)
Analog DIM input voltage rang
Analog Adjust Output Current
DIM Pin Drive Current
Absolute Maximum Ratings: 8V
0.4 to 1.7
0-100
<1.5
V
%
µA
0.3≤Vdim≤1.3V
PWM Control Voltage Range Limits
1.7≤Vdim≤5.0
V
PWM Recommended Operating
Frequency
100Hz-100KHz
PWM Adjust Output Current
1 – 100 (see graph)
%
Output Specifications
Parameters
Current accuracy
Conditions
Typical
±5
Maximum
Units
%
Output Voltage range
Output current
See model table
Vout-Vin≥5V
14-48
See model table
VDC
Short Circuit protection
Over Voltage Protection
Under Voltage Protection
Soft Start Time
Temperature coefficient
Ripple & Noise
Automatic Recovery (Cut-off Output)
52.5
50
Vdc
V
Cool Start
≤7.6
ms
±0.03
%/oC
20MHz Bandwidth
See model table
www.aimtec.com
F 051e R12.E
Tel: +1 514 620 2722
1 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMLB-Z
Up to 700mA | Step Up LED Driver
General Specifications
Parameters
Operating frequency
Conditions
Depending on the model
AMLB-3615Z
Typical
360-380
Maximum
Units
KHz
-40 to +85
AMLB-3625Z; AMLB-3630Z
AMLB-3635Z
-40 to +80 (Vin 9-18V) / -40 to +85 (Vin 18-36V)
-40 to +75 (Vin 9-18V) / -40 to +85 (Vin 18-36V)
Operating temperature
oC
AMLB-3650Z
-40 to +70 (Vin 9-18V) / -40 to +80 (Vin 18-36V)
AMLB-3660Z; AMLB-3670Z
-40 to +70 (Vin 9-18V) / -40 to +75 (Vin 18-36V)
-55 to +125
Storage temperature
Maximum case temperature
Thermal Impedance
Cooling
oC
oC
100
Depending on the model
+13.7 to +17
oC/W
Free air convection
Humidity
95
% RH
Case material
Weight
Non-Conductive Black Plastic (UL94-V0 rated)
38
g
Dimensions (L x W x H)
MTBF
Maximum Soldering Temperature 1.5mm from case for 10sec.
2.03 x 1.03 x 0.62 inches
51.50 x 26.10 x 15.80 mm
> 1 290 000 hrs (MIL-HDBK-217 F at +25 oC/Vin=9V,Vout=38V)
260
oC
NOTES:
1. To prevent burning out the driver, the output voltage must be 5.0VDC higher than the input voltage
2. Do NOT exceed the maximum power ratings on each model
3. With output ripple being rather low, it is recommended not to increase the additional output capacitor so s not to increase the delay while starting up
under cool start conditions
4. This series offers protection in case the output is shorted. After the short occurs, the input current will be cut off and recovers when the short is removed
5. The reference value of under voltage protection (7.6V) means that under the condition of cool start and full discharge of output, the protection starts when
input voltage is lower than 7.6V
6. Note: PWM dimming means PWM signals are converted into mimic analog voltage by internal circuits and then do the dimming. The advantage of this
approach is to reduce the EMI
Safety Specifications
Parameters
Agency approvals
CE, EN 55015, EN 61547, NOTE: Designed to meet EN 55022 Class B, IEC/EN 60950-1 , UL8750,
IEC/EN 61347-2-13
Electrostatic Discharge Immunity
RF, Electromagnetic Field Immunity
Electrical Fast Transient/Burst Immunity
Surge Immunity
RF, Conducted Disturbance Immunity
Power frequency Magnetic Field Immunity
Voltage dips, Short Interruptions Immunity
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
Standards
Pin Out Specifications
Pin
Single
1
2
3
4
+Vi
DIM
ON/OFF
-Vi
+ DC Supply
PWM/Analog Dimming Control
Remote ON/OFF
-DC Supply
5
6
+LED
-LED
LED Anode connection
LED Cathode connection
www.aimtec.com
F 051e R12.E
Tel: +1 514 620 2722
2 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMLB-Z
Up to 700mA | Step Up LED Driver
Operating Temperature
Free Air Convection
AMLB-3615Z
AMLB-3625Z (Vin:18V-36V)
AMLB-3630Z (Vin:18V-36V)
AMLB-3635Z (Vin: 18V-36V)
100
80
AMLB-3650Z (Vin:18V-36V)
AMLB-3625Z (Vin:9V-18V)
AMLB-3630Z (Vin:9V-18V)
60
Safe Operating Area
AMLB-3635Z (Vin:9V-18V)
AMLB-3660Z (Vin:18V-36V)
AMLB-3670Z (Vin:18V-36V)
40
20
AMLB-3650Z (Vin:9V-18V)
AMLB-3660Z (Vin:9V-18V)
AMLB-3670Z (Vin:9V-18V)
0
70 75 85
-
-
100
40
20
0
20
40
60
80
Ambient Temperature
º C
Dimensions
51.50
(2.03)
45.72
(1.80)
5
1
2
26.10
(1.03)
20.32
(0.80)
Top View
20.32
(0.80)
3
4
6.77
(0.27)
6
Mechanical Tolerances
51.50
(2.03)
Case tolerance ± 0.5mm or ± 0.02 inches
Pin diameter 1.0 ± 0.05mm or 0.04 ± 0.002 inches
Pin Pitch tolerance: ± 0.35 or ± 0.014
15.80
(0.62)
5.08
(0.2)
min
1.00
(0.04)
45.72
(1.80)
www.aimtec.com
F 051e R12.E
Tel: +1 514 620 2722
3 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMLB-Z
Up to 700mA | Step Up LED Driver
EN55022 Class B Filter Suggestion:
L1
+Vin
+Vi
-Vi
1st
LED
+LED
NF
1
4
5
1
C3
C1
C2
AMLB-Z
6
2
3
1
DIM
PWM/Analog
Dimming Control
EN
Last
LED
-Vin
-LED
L2
C1à47uF/100V
C2à330uF/100V
C3à330uF/100V
L1à14uH/4A
L2à14uH/4A
NFà5.6mH/5A(Command Choke)
Application circuit examples:
+LED
+Vin
1
4
+LED
5
6
1st LED
+Vin
-Vin
1
1
4
5
6
AMLB-Z
3
AMLB-Z
-Vin
1st LED
Last LED
2
1
1
1
DIM
2
3
PWM/Analog
Dimming Control
EN
-LED
DIM
EN
PWM/Analog
Dimming Control
Last LED
1
1
-LED
+LED
5
+Vin
1st LED
1
4
1
AMLB-Z
SW
SW
ON
Vout
0V
-Vin
DIM
2
EN
6
Last LED
3
ON
OFF
1
OFF
normal
-LED
AC In
6.5Vac
to 25Vac
+Vin
+LED
-LED
1
5
6
1st LED
+
-
100uF to
330uF
1
0.1uF
optional
AMLB-Z
4
-Vin
Last LED
2
3
1
AC In
DIM
PWM/Analog
Dimming Control
EN
www.aimtec.com
F 051e R12.E
Tel: +1 514 620 2722
4 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMLB-Z
Up to 700mA | Step Up LED Driver
Under Voltage
Protection
Under Voltage Protection
R1
+LED
-LED
+Vin
1
X
7.6V
1st LED
5
1
12K
10K
7.5K
4.7K
3.3K
2.7K
2.4K
2.0K
1.8K
10.8V
11.6V
13.0V
16.5V
21.0V
24.1V
26.2V
29.8V
32.4V
AMLB-Z
R1
6
4
-Vin
DIM
2
EN
3
Last LED
1
*R1 Value only supplies the reference
Output Current Adjustment by External DC Control Voltage (VCTRL):
+Vin
+LED
5
1
2
1st LED
1
AMLB-Z
0.4V-1.7V
DC
+Vin
DIM
6
4
3
Last LED
-Vin
1
R1
EN
GND
-LED
If Vin is between 9 VDC and 36 VDC it is
recommended to use the circuit shown below
R2
DIM
+5v
30K
380K
+Vin
+LED
5
1st LED
1
1
R1
380K
AMLB-Z
DIM
-Vin
200K
2
1
VR
6
TL431
+Vin
+LED
-LED
Last LED
1
1st LED
3
5
6
4
1
1
AMLB-Z
EN
2
VR
200K
DIM
-LED
0V-1.7V
-Vin
4
3
Vin
5V
R1
1
EN
4.7K
18K
43K
62K
12V
24V
36V
0 – 10VDC
DIM
R1
1M
+Vin
+LED
1st LED
1
0V-1.7V
2 DIM
5
1
AMLB-Z
6
R2
-Vin
4
210K
3
1
EN
-LED
www.aimtec.com
F 051e R12.E
Tel: +1 514 620 2722
5 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMLB-Z
Up to 700mA | Step Up LED Driver
Output Current Adjustment by PWM Control:
A Pulse Width Modulation (PWM) signal with a duty cycle DPWM can be applied to the DIM pin as shown below.
+Vin
-Vin
+LED
1st LED
1
4
5
6
1
PWM
AMLB-Z
5V
0V
Last LED
2
3
1
DIM
EN
-LED
Driving DIM Via Open Collector Transistor
The DIM pin can also be driven via an open collector transistor as shown below.
+5V
12K
+LED
+Vin
1st LED
1
4
5
6
1
AMLB-Z
210K
GND
PWM
-Vin
Last LED
2
3
1
2SD1782K
DIM
EN
-LED
Driving the VADJ from a Microcontroller
The DIM can be driven from an open drain output of a microcontroller as shown below.
+5V
12K
+LED
+Vin
1st LED
5
1
1
MCU
AMLB-Z
4
-Vin
6
Last LED
2
3
1
2SK3018
DIM
EN
-LED
GND
www.aimtec.com
F 051e R12.E
Tel: +1 514 620 2722
6 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMLB-Z
Up to 700mA | Step Up LED Driver
Output Current Adjustment by PWM Control (Dimming):
A PWM signal must have a frequency of greater than 100Hz to prevent any visible flicker.
Output Current Adjustment by PWM Control (Flash):
Output Current vs DIM Voltage:
AMLB-3615Z
800
AMLB-3625Z
AMLB-3630Z
AMLB-3635Z
AMLB-3650Z
AMLB-3660Z
AMLB-3670Z
700
600
500
400
300
200
100
0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 3.0 4.0 5.0
DIM voltage (V)
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer
controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary
based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C,
humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all
internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for
release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications
which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at
www.aimtec.com.
www.aimtec.com
F 051e R12.E
Tel: +1 514 620 2722
7 of 7
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
相关型号：
©2020 ICPDF网 联系我们和版权申明