AM10C-2412S-NZ [AIMTEC]
DC-DC Converter;
| 型号： | AM10C-2412S-NZ |
| 厂家： | 
AIMTEC |
| 描述： | DC-DC Converter |
| 文件： | 总4页 (文件大小：633K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Series AM10C-NZ
10 Watt | DC-DC Converter
Picture coming soon
FEATURES:
• Wide 2:1 Input Voltage Range
• High efficiency up to 88%
• 1500 VDC Isolation
• Over Current Protection
• No load consumption ≤ 0.12W
•
•
•
•
•
Operating Temperature -40ºC to +85ºC
Output Over Voltage protection
Continuous Short Circuit Protection
Input Under Voltage Protection
Remote On/Off control
Models
Single output
Output
Voltage
Output
Current max
Max
Input
Voltage (V)
Isolation
(VDC)
Efficiency
(%)
Model
Capacitive
Load (uF)
2200
(V)
5
12
15
24
(A)
2
0.83
0.66
0.41
AM10C-2405S-NZ
AM10C-2412S-NZ
AM10C-2415S-NZ
AM10C-2424S-NZ
18-36
18-36
18-36
18-36
1500
1500
1500
1500
83
87
88
88
470
330
100
*Add suffix “-ST” for optional screw terminal bottom plate
**Add suffix “-STD” for optional DIN Rail screw terminal bottom plate
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Parameters
Nominal
Typical
Maximum
Units
Voltage range
24 Vin
18-36
VDC
Filter
Pi
Absolute Maximum Rating (1s)
No Load Input Current
Input reflected ripple current
24 Vin
24 Vin
24 Vin
-0.7 - 50
12
VDC
mA
mA
40
15.5
10
Input Under voltage protection
Startup time
24 Vin
VDC
ms
Nominal input, resistive load
On
Off
3.5-12VDC or leave open
0-1.2VDC or connect to GND, idle current 6-10mA
Remote On/Off Control
Isolation Specifications
Parameters
Tested I/O voltage
Resistance
Conditions
60 sec, <1mA
500VDC
Typical
1500
Maximum
Units
VDC
MOhm
pF
>1000
Capacitance
I/O, 100KHz/0.1V
1000
Output Specifications
Parameters
Conditions
Typical
Maximum
Units
Voltage accuracy
5% to 100% load
±1
±3
%
Over voltage protection
Over current protection
Short Circuit protection
Short circuit restart
110-160
110-190
Continuous
Auto-Recovery
% of Vout
% of Iout
Line voltage regulation
Load voltage regulation
Temperature coefficient
Ripple & Noise
Transient recovery time
Transient recovery deviation
Full load, LL to HL
5% to 100% load
±0.5
±1
±0.03
100
500
±5
% of Vin
%
100% load
%/oC
mV p-p
µs
20MHz Bandwidth, 5-100% load
25% load step change
25% load step change
%
www.aimtec.com
F 051e R2
Tel: +1 514 620 2722
1 of 4
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AM10C-NZ
10 Watt | DC-DC Converter
General Specifications
Parameters
Switching frequency
Operating temperature
Storage temperature
Maximum case temperature
Cooling
Conditions
100% load
See derating curve
Typical
350
Maximum
Units
KHz
oC
-40 to +85
-55 to +125
oC
100
95
oC
Free air convection
Aluminum Alloy
Humidity
Case material
% RH
g
Pin mountable
15
35
55
Weight
With optional -ST mounting plate:
With optional -STD mounting plate:
Pin mountable
1 x 1 x 0.46 inches
25.40 x 25.40 x 11.70 mm
Dimensions (L x W x H)
With optional -ST mounting plate:
With optional -STD mounting plate:
2.99 x 1.24 x 0.84 inches 76.00 x 31.50 x 21.20 mm
2.99 x 1.24 x 1.02 inches 76.00 x 31.50 x 25.80 mm
>1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25oC)
MTBF
Maximum soldering temperature
1.5mm from case for 10 sec
300
oC
Environmental Specifications
Parameters
Test mode
Acceleration
10-55Hz
Vibration
10G, 30min one cycle, every axis tested
Safety Specifications
Parameters
Designed to meet IEC/EN/UL60950-1
EN 55022, class B (with the recommended EMC circuit)
Electrostatic Discharge Immunity
RF, Electromagnetic Field Immunity
Electrical Fast Transient / Burst Immunity
Surge Immunity
RF, Conducted Disturbance Immunity
Voltage dips, Short Interruptions & Voltage
variations Immunity
IEC 61000-4-2, Contact ±4KV, Criteria B
IEC 61000-4-3, 10V/m, Criteria A
IEC 61000-4-4, ±2KV, Criteria B (with the recommended EMC circuit)
IEC 61000-4-5, ±2KV, Criteria B (with the recommended EMC circuit)
IEC 61000-4-6, 3 Vrms, Criteria A
Standards
IEC 61000-4-29: 0-70%, Criteria B
Dimensions
Pin Out Specifications
Bottom View
Top View
25.40
(1.00)
Single
+V Input
-V Input
Pin
1
2
2.54
(0.10)
10.16
(0.40)
10.16
(0.40)
3
4
5
On/Off Control
+V Output
No pin
5
6
4
+V Output
-V Output
6
-V Output
+V
-V
Input
Input
CTRL
1
2
3
7.62
(0.30)
10.16
(0.40)
5.08
(0.20)
Side View
Printed Face
Dimensions mm (inch)
Case Tolerance ±0.50 (±0.02)
Pin Diameter 1.0 ± 0.10 (0.04 ± 0.004)
2.54
(0.10)
ᴓ 1.00
(0.39)
www.aimtec.com
F 051e R2
Tel: +1 514 620 2722
2 of 4
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AM10C-NZ
10 Watt | DC-DC Converter
Screw Terminal Option: AM10C-NZ-ST
Single
NC
-V Input
+V Input
Dual
NC
-V Input
+V Input
Pin
1
2
76.00
(2.99)
61.60
(2.43)
LED lamp
Ø3.30
3
4
5
6
-V Output -V Output
NC Common
+V Output +V Output
1
2
3
4
5
6
Top View
Note:
Ø3.30
Unit: mm (inch)
Wire range: 24-12 AWG
Tightening torque: Max 0.4 N*m
General tolerances: ±0.50 (±0.02)
Front View
DIN-RAIL Option: AM10C-NZ-STD
76.00
(2.99)
Single
NC
Dual
NC
Pin
1
61.60
(2.43)
LED lamp
2
3
-V Input
+V Input
-V Input
+V Input
4
5
6
-V Output -V Output
NC Common
+V Output +V Output
1
4
5
6
2
Top View
3
Note:
Front View
Unit: mm (inch)
Mounting rail: TS35
Wire range: 24-12 AWG
Tightening torque: Max 0.4 N*m
General tolerances: ±0.50 (±0.02)
www.aimtec.com
F 051e R2
Tel: +1 514 620 2722
3 of 4
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
Series AM10C-NZ
10 Watt | DC-DC Converter
Derating
Free Air Convection
º
C
5V model
65
100
80
º
C Other models
71
60
40
Safe Operating Area
20
0
65 71
60
85
80
100
- 40 - 20
0
20
40
º C
Ambient Temperature
Recommended EMC Circuits
CY1
1nF/2KV
LCM
4.7mH
F1
+Vo
C5
+Vin
C3
C4
C1
C2
MOV
DC-DC Converter
-Vo
-Vin
CY2
1nF/2KV
24V input
MOV
C1
C2
S20K30
680µF/50V
1µF/50V
C3
C4
C5
330µF/50V
4.7µF/50V
10µF/50V
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 051e R2
Tel: +1 514 620 2722
4 of 4
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
相关型号：
AM10C-2412S-NZ-STD
DC/DC Converter; Product Weight (grams): 55; Input voltage min (V): 18; Input voltage max (V): 36; Output voltage min: 12; Output voltage max: 12; Output voltage dual assymetric (y/n): Single; Output Power (W): 10; Max Output current (A): 0.83; Efficiency (%): 87; Max Capacitive load (µF): 470; Package type: 1x1; Mounting: PCB; W (in): 2.99; L (in): 1.24; H (in): 1.02; W (mm): 76; L (mm): 31.5; H (mm): 25.92; Min Operating temperature: -40; Max operating temperature (°C): 85; Isolation (VDC): 1500; EMC compliance 1: EN 55022 Class A; EMC compliance 2: EN 55022 Class B; Case material: Aluminum
AIMTEC
©2020 ICPDF网 联系我们和版权申明