AD534JDZ [ADI]
Internally Trimmed Precision IC Multiplier; 内部微调精密IC乘法器型号: | AD534JDZ |
厂家: | ADI |
描述: | Internally Trimmed Precision IC Multiplier |
文件: | 总21页 (文件大小:575K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Internally Trimmed
Precision IC Multiplier
AD534
FUNCTIONAL BLOCK DIAGRAM
FEATURES
STABLE
REFERENCE
AND BIAS
+V
S
Pretrimmed to 0.2ꢀ5 maximum 4-quadrant error (ADꢀ34L)
All inputs (X, Y, and Z) differential, high impedance for
[(X1 − X2)(Y1 − Y2)/10 V] + Z2 transfer function
Scale factor adjustable to provide up to ×100 gain
Low noise design: 90 μV rms, 10 Hz to10 kHz
Low cost, monolithic construction
SF
–V
S
TRANSFER FUNCTION
X
X
1
2
V-TO-1
V-TO-1
V-TO-1
(X – X ) (Y – Y )
1
2
1
2
– (Z – Z )
V
= A
A
1
2
OUT
SF
TRANSLINEAR
MULTIPLIER
ELEMENT
Y
Y
1
2
Excellent long-term stability
OUT
HIGH GAIN
OUTPUT
AMPLIFIER
APPLICATIONS
Z
Z
1
2
0.75 ATTEN
High quality analog signal processing
Differential ratio and percentage computations
Algebraic and trigonometric function synthesis
Wideband, high crest rms-to-dc conversion
Accurate voltage controlled oscillators and filters
Available in chip form
Figure 1.
GENERAL DESCRIPTION
The AD534 is a monolithic laser trimmed four-quadrant multi-
plier divider having accuracy specifications previously found
only in expensive hybrid or modular products. A maximum
multiplication error of ±±.ꢀ5ꢁ is guaranteed for the AD534L
without any external trimming. Excellent supply rejection, low
temperature coefficients and long-term stability of the on-chip
thin film resistors and buried Zener reference preserve accuracy
even under adverse conditions of use. It is the first multiplier to
offer fully differential, high impedance operation on all inputs,
including the Z input, a feature that greatly increases its
standard value of 1±.±± V; by means of an external resistor, this
can be reduced to values as low as 3 V.
The wide spectrum of applications and the availability of several
grades commend this multiplier as the first choice for all new
designs. The AD534J (±1ꢁ maximum error), AD534K (±±.5ꢁ
maximum), and AD534L (±±.ꢀ5ꢁ maximum) are specified for
operation over the ±°C to +7±°C temperature range. The AD534S
(±1ꢁ maximum) and AD534T (±±.5ꢁ maximum) are specified
over the extended temperature range, −55°C to +1ꢀ5°C. All
grades are available in hermetically sealed TO-1±± metal cans
and SBDIP packages. AD534K, AD534S, and AD534T chips are
also available.
flexibility and ease of use. The scale factor is pretrimmed to the
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©1977–2011 Analog Devices, Inc. All rights reserved.
IMPORTANT LINKS for the AD534*
Last content update 09/07/2013 04:03 pm
PARAMETRIC SELECTION TABLES
DESIGN SUPPORT
Submit your support request here:
Linear and Data Converters
Embedded Processing and DSP
Find Similar Products By Operating Parameters
Telephone our Customer Interaction Centers toll free:
DOCUMENTATION
Americas:
Europe:
China:
1-800-262-5643
00800-266-822-82
4006-100-006
AN-213: Low Cost, Two-Chip, Voltage -Controlled Amplifier and Video
Switch
India:
1800-419-0108
8-800-555-45-90
Working with Batteries
PCN#00-406
Russia:
Quality and Reliability
Lead(Pb)-Free Data
Aerospace Dice
Standard Space Level Products Program
Space Qualified Parts List
SAMPLE & BUY
AD534
EVALUATION KITS & SYMBOLS & FOOTPRINTS
Symbols and Footprints
View Price & Packaging
Request Evaluation Board
Request Samples
Check Inventory & Purchase
Find Local Distributors
DESIGN COLLABORATION COMMUNITY
Collaborate Online with the ADI support team and other designers
about select ADI products.
Follow us on Twitter: www.twitter.com/ADI_News
Like us on Facebook: www.facebook.com/AnalogDevicesInc
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet.
Note: Dynamic changes to the content on this page (labeled 'Important Links') does not
constitute a change to the revision number of the product data sheet.
This content may be frequently modified.
AD534
TABLE OF CONTENTS
Features .............................................................................................. 1
Functional Description.................................................................. 12
Provides Gain with Low Noise ..................................................... 12
Operation as a Multiplier .......................................................... 12
Operation as a Squarer .............................................................. 13
Operation as a Divider............................................................... 13
Operation as a Square Rooter................................................... 14
Unprecedented Flexibility ......................................................... 14
Applications Information.............................................................. 15
Outline Dimensions....................................................................... 17
Ordering Guide .......................................................................... 18
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 7
Thermal Resistance ...................................................................... 7
ESD Caution.................................................................................. 7
Pin Configurations and Function Descriptions ........................... 8
Typical Performance Characteristics ........................................... 10
REVISION HISTORY
4/11—Rev. B to Rev. C
Changes to Features Section, Figure 1, and
General Description Section........................................................... 1
Added Pin Configurations and Function Descriptions
Section................................................................................................ 8
Moved Provides Gain with Low Noise Section .......................... 12
Moved Unprecedented Flexibility Section .................................. 14
Updated Outline Dimensions....................................................... 17
Changes to Ordering Guide .......................................................... 18
Rev. C | Page 2 of 20
AD534
SPECIFICATIONS
TA = 25°C, ±±S = ±15 ±, R ≥ 2 kΩ, all minimum and maximum specifications are guaranteed, unless otherwise noted.
Table 1.
AD534J
Min Typ
AD534K
Typ
AD534L
Typ
Parameter
Max
Min
Max Min
Max
Unit
MULTIPLIER PERFORMANCE
Transfer Function
(X1 − X2 )(Y1 −Y2 )
(X1 − X2 )(Y1 −Y2 )
(X1 − X2 )(Y1 −Y2 )
+ Z2
+ Z2
0.ꢀ2
+ Z2
10 ±
10 ±
10 ±
Total Error 1 (−10 V ≤ X, Y ≤ +10 V)
TA = TMIN to TMAX
1.02
0.2ꢀ2
%
%
1.ꢀ
1.0
0.ꢀ
Total Error vs. Temperature
Scale Factor Error
0.022
0.01ꢀ
0.00ꢁ
%/°C
(SF = 10.000 V Nominal)3
Temperature Coefficient of
Scaling Voltage
Supply Rejection ( 1ꢀ V 1 V)
Nonlinearity, X (X = 20 V p-p,
Y = 10 V)
Nonlinearity, Y (Y = 20 V p-p, X = 10 V
Feedthroughꢂ, X (Y Nulled,
X = 20 V p-p ꢀ0 Hz)
0.2ꢀ
0.1
0.1
%
0.02
0.01
0.ꢂ
0.01
0.01
0.2
0.00ꢀ
0.01
0.10
%/°C
%
%
0.32
0.122
0.2
0.3
0.1
0.1ꢀ
0.12
0.32
0.00ꢀ
0.0ꢀ
0.12
0.122
%
%
Feedthroughꢂ, Y (X Nulled,
Y = 20 V p-p, ꢀ0 Hz)
Output Offset Voltage
Output Offset Voltage Drift
DYNAMICS
0.01
0.01
0.12
1ꢀ2
0.003
0.12
102
%
ꢀ
200
302
2
100
2
100
mV
μV/°C
Small Signal BW (VOUT = 0.1 rms)
1% Amplitude Error (CLOAD = 1000 pF)
Slew Rate (VOUT 20 p-p)
Settling Time (to 1%, D VOUT = 20 V)
NOISE
1
1
1
MHz
kHz
V/μs
μs
ꢀ0
20
2
ꢀ0
20
2
ꢀ0
20
2
Noise Spectral Density
SF = 10 V
SF = 3 Vꢀ
0.ꢁ
0.ꢂ
0.ꢁ
0.ꢂ
0.ꢁ
0.ꢂ
μV/√Hz
μV/√Hz
Wideband Noise
f = 10 Hz to ꢀ MHz
f = 10 Hz to 10 kHz
1
90
1
90
1
90
mV rms
μV rms
OUTPUT
Output Voltage Swing
Output Impedance (f ≤ 1 kHz)
Output Short-Circuit Current
112
0.1
112
112
0.1
V
Ω
0.1
(RL = 0 Ω, TA = TMIN to TMAX
)
30
70
30
70
30
70
mA
dB
Amplifier Open-Loop Gain (f = ꢀ0 Hz)
INPUT AMPLIFIERS (X, Y, and Z)6
Signal Voltage Range
Differential or Common Mode
Operating Differential
Offset Voltage (X, Y)
Offset Voltage Drift (X, Y)
Offset Voltage (Z)
10
12
ꢀ
100
ꢀ
10
12
2
ꢀ0
2
10
12
2
ꢀ0
2
V
V
202
302
102
1ꢀ2
102
102
mV
μV/°C
mV
μV/°C
dB
Offset Voltage Drift (Z)
CMRR
200
ꢁ0
100
90
100
90
602
702
702
Rev. C | Page 3 of 20
AD534
AD534J
Min Typ
AD534K
Typ
AD534L
Typ
Parameter
Max
Min
Max Min
Max
2.02
0.22
Unit
μA
μA
Bias Current
Offset Current
Differential Resistance
DIVIDER PERFORMANCE
Transfer Function (X1 > X2)
0.ꢁ
0.1
10
2.02
0.ꢁ
0.1
10
2.02
0.ꢁ
0.0ꢀ
10
MΩ
(Z2 −Z1 )
(Z2 −Z1 )
(Z2 −Z1 )
10 ±
+Y1
10 ±
+Y1
10 ±
+Y1
(X1 −X 2 )
(X1 −X 2 )
(X1 −X 2 )
Total Error1
X = 10 V, −10 V ≤ Z ≤ +10 V
X = 1 V, −1 V ≤ Z ≤ +1 V
0.1 V ≤ X ≤ 10 V, −10 V ≤ Z ≤ +10 V
SQUARER PERFORMANCE
Transfer Function
0.7ꢀ
2.0
2.ꢀ
0.3ꢀ
1.0
1.0
0.2
0.ꢁ
0.ꢁ
%
%
%
(X1 −X2 )2
(X1 −X2 )2
(X1 −X2 )2
+Z2
+Z2
+Z2
10 ±
10 ±
10 ±
Total Error (−10 V ≤ X ≤ +10 V)
SQUARE-ROOTER PERFORMANCE
Transfer Function (Z1 ≤ Z2)
Total Error1 (1 V ≤ Z ≤ 10 V)
POWER SUPPLY SPECIFICATIONS
Supply Voltage
0.6
0.3
0.2
%
%
√(10 V(Z2 – Z1)) + X2
√(10 V(Z2 – Z1)) + X2
√(10 V(Z2 – Z1)) + X2
1.0
0.ꢀ
0.2ꢀ
Rated Performance
Operating
Supply Current
Quiescent
1ꢀ
1ꢀ
1ꢀ
V
V
ꢁ
1ꢁ2
62
ꢁ
1ꢁ2
62
ꢁ
1ꢁ2
62
ꢂ
ꢂ
ꢂ
mA
1 Specifications given are percent of full scale, 10 V (that is, 0.01% = 1 mV).
2 Tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels.
3 Can be reduced down to 3 V using external resistor between –VS and SF.
ꢂ Irreducible component due to nonlinearity; excludes effect of offsets.
ꢀ Using external resistor adjusted to give SF = 3 V.
6 See Figure 1 for definition of sections.
Rev. C | Page ꢂ of 20
AD534
TA = 25°C, ±±S = ±15 ±, R ≥ 2 kΩ, all minimum and maximum specifications are guaranteed, unless otherwise noted.
Table 2.
AD534S
Min Typ
AD534T
Min Typ
Parameter
Max
Max
Unit
MULTIPLIER PERFORMANCE
Transfer Function
(X1 − X2 )(Y1 −Y2 )
(X1 − X2 )(Y1 −Y2 )
+ Z2
+ Z2
0.ꢀ2
10 ±
10 ±
Total Error 1 (−10 V ≤ X, Y ≤ +10 V)
TA = TMIN to TMAX
Total Error vs. Temperature
1.02
2.02
0.022
%
%
1.0
0.012 %/°C
Scale Factor Error
(SF = 10.000 V Nominal)3
Temperature Coefficient of Scaling Voltage
Supply Rejection ( 1ꢀ V 1 V)
Nonlinearity, X (X = 20 V p-p, Y = 10 V)
Nonlinearity, Y (Y = 20 V p-p, X = 10 V
Feedthroughꢂ, X (Y Nulled,
X = 20 V p-p, ꢀ0 Hz)
0.2ꢀ
0.02
0.01
0.ꢂ
0.1
%
%/°C
%
%
%
0.01
0.01
0.2
0.32
0.12
0.2
0.1
0.3
0.1ꢀ
0.32
%
Feedthroughꢂ, Y (X Nulled,
Y = 20 V p-p, ꢀ0 Hz)
0.01
ꢀ
0.01
2
0.12
1ꢀ2
3002
%
mV
μV/°C
Output Offset Voltage
Output Offset Voltage Drift
DYNAMICS
302
ꢀ002
Small Signal BW (VOUT = 0.1 rms)
1% Amplitude Error (CLOAD = 1000 pF)
Slew Rate (VOUT 20 p-p)
Settling Time (to 1%, ΔVOUT = 20 V)
NOISE
1
1
MHz
kHz
V/μs
μs
ꢀ0
20
2
ꢀ0
20
2
Noise Spectral Density
SF = 10 V
SF = 3 Vꢀ
0.ꢁ
0.ꢂ
0.ꢁ
0.ꢂ
μV/√Hz
μV/√Hz
Wideband Noise
f = 10 Hz to ꢀ MHz
f = 10 Hz to 10 kHz
1
90
1
90
mV/rms
μV/rms
OUTPUT
Output Voltage Swing
Output Impedance (f ≤ 1 kHz)
Output Short-Circuit Current (RL = 0 Ω, TA = TMIN to TMAX
Amplifier Open-Loop Gain (f = ꢀ0 Hz)
INPUT AMPLIFIERS (X, Y, and Z)6
Signal Voltage Range
112
112
V
0.1
30
70
0.1
30
70
Ω
mA
dB
)
Differential or Common Mode
Operating Differential
Offset Voltage (X, Y)
Offset Voltage Drift (X, Y)
Offset Voltage (Z)
Offset Voltage Drift (Z)
CMRR
Bias Current
10
12
ꢀ
100
ꢀ
10
12
2
1ꢀ0
2
V
V
202
102
mV
μV/°C
mV
μV/°C
dB
μA
μA
MΩ
302
ꢀ002
1ꢀ2
3002
602
ꢁ0
0.ꢁ
0.1
10
702
90
2.02
0.ꢁ
0.1
10
2.02
Offset Current
Differential Resistance
Rev. C | Page ꢀ of 20
AD534
AD534S
AD534T
Parameter
Min Typ
Max
Min Typ
Max
Unit
DIVIDER PERFORMANCE
Transfer Function (X1 > X2)
(Z2 −Z1 )
(X1 −X 2)
(Z2 −Z1 )
(X1 −X 2)
10 ±
+Y1
10 ±
+Y1
Total Error1
X = 10 V, −10 V ≤ Z ≤ +10 V
X = 1 V, −1 V ≤ Z ≤ +1 V
0.1 V ≤ X ≤ 10 V, −10 V ≤ Z ≤ +10 V
SQUARER PERFORMANCE
Transfer Function
0.7ꢀ
2.0
2.ꢀ
0.3ꢀ
1.0
1.0
%
%
%
(X1 −X2 )2
(X1 −X2 )2
+Z2
+Z2
10 ±
10 ±
Total Error (−10 V ≤ X ≤ +10 V)
SQUARE-ROOTER PERFORMANCE
Transfer Function (Z1 ≤ Z2)
Total Error1 (1 V ≤ Z ≤ 10 V)
POWER SUPPLY SPECIFICATIONS
Supply Voltage
0.6
0.3
%
%
√(10 V(Z2 – Z1)) + X2
√(10 V(Z2 – Z1)) + X2
1.0
0.ꢀ
Rated Performance
Operating
Supply Current
Quiescent
1ꢀ
1ꢀ
V
V
ꢁ
222
62
ꢁ
222
62
ꢂ
ꢂ
mA
1 Specifications given are percent of full scale, 10 V (that is, 0.01% = 1 mV).
2 Tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels.
3 Can be reduced down to 3 V using external resistor between –VS and SF.
ꢂ Irreducible component due to nonlinearity: excludes effect of offsets.
ꢀ Using external resistor adjusted to give SF = 3 V.
6 See Figure 1 for definition of sections.
Rev. C | Page 6 of 20
AD534
ABSOLUTE MAXIMUM RATINGS
X
+V
OUT
1
S
Table 3.
X
2
5
3
4
AD534J,
AD534K,
AD534L
AD534S,
AD534T
8
A
Parameter
0.076
(1.93)
Supply Voltage
Internal Power Dissipation
1ꢁ V
ꢀ00 mW
22 V
ꢀ00 mW
SF
Output Short Circuit to
Ground
Input Voltages (X1, X2, Y1, Y2,
Z1, Z2)
Z
1
Indefinite
VS
Indefinite
VS
Rated Operating
Temperature Range
Storage Temperature
Range
Lead Temperature Range,
60 sec Soldering
0°C to +70°C
−6ꢀ°C to +1ꢀ0°C
300°C
−ꢀꢀ°C to +12ꢀ°C
−6ꢀ°C to +1ꢀ0°C
300°C
Y
1
Y
–V
Z
2
2
S
0.100 (2.54)
Figure 2. Chip Dimensions and Bonding Diagram
Dimensions shown in inches and (mm)
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Contact factory for latest dimensions.
+V
S
470kΩ
TO APPROPRIATE
INPUT TERMINAL
50kΩ
1kΩ
THERMAL RESISTANCE
–V
S
Figure 3. Optional Trimming Configuration
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
ESD CAUTION
Table 4. Thermal Resistance
Package Type
θJA
1ꢀ0
9ꢀ
θJC
2ꢀ
2ꢀ
2ꢀ
Unit
°C/W
°C/W
°C/W
10-Pin TO-100 (H-10)
1ꢂ-Lead SBDIP (D-1ꢂ)
20-Terminal LCC (E-20-1)
9ꢀ
Rev. C | Page 7 of 20
AD534
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
+V
S
OUT
X1
9
8
10
Z1
7
6
AD534
TOP VIEW
(Not to
X2
1
Z2
2
Scale)
SF
5
3
4
–V
S
Y1
Y2
Figure 4. TO-100 (H-10) Pin Configuration
Table 5. H-10 Package Pin Function Descriptions
Pin No.
Mnemonic
Description
1
2
3
ꢂ
ꢀ
6
7
ꢁ
9
10
X2
SF
Y1
Y2
−VS
Z2
Z1
OUT
+VS
X1
Inverting Differential Input of the X Multiplicand Input.
Scale Factor Input.
Noninverting Differential Input of the Y Multiplicand Input.
Inverting Differential Input of the Y Multiplicand Input.
Negative Supply Rail.
Inverting Differential Input of the Z Reference Input.
Noninverting Differential Input of the Z Reference Input.
Product Output.
Positive Supply Rail.
Noninverting Differential Input of the X Multiplicand Input.
X1
X2
NC
SF
NC
Y1
Y2
1
2
3
4
5
6
7
14 +V
S
13 NC
12 OUT
11 Z1
AD534
TOP VIEW
(Not to Scale)
10 Z2
9
8
NC
–V
S
NC = NO CONNECT. DO NOT
CONNECT TO THIS PIN.
Figure 5. TO-100 (D-14) Pin Configuration
Table 6. D-14 Package Pin Function Descriptions
Pin No.
Mnemonic
Description
1
2
X1
X2
NC
SF
Noninverting Differential Input of the X Multiplicand Input.
Inverting Differential Input of the X Multiplicand Input.
No Connect. Do not connect to this pin.
Scale Factor Input.
3, ꢀ, 9, 13
ꢂ
6
7
ꢁ
10
11
12
1ꢂ
Y1
Y2
−VS
Z2
Z1
Noninverting Differential Input of the Y Multiplicand Input.
Inverting Differential Input of the Y Multiplicand Input.
Negative Supply Rail.
Inverting Differential Input of the Z Reference Input.
Noninverting Differential Input of the Z Reference Input.
Product Output.
OUT
+VS
Positive Supply rail.
Rev. C | Page ꢁ of 20
AD534
3
2
1
20 19
18
17
16
15
14
4
5
6
7
8
OUT
NC
Z1
NC
NC
SF
NC
NC
AD534
TOP VIEW
(Not to Scale)
NC
Z2
9
10 11 12 13
NC = NO CONNECT. DO NOT
CONNECT TO THIS PIN.
Figure 6. LCC (E-20-1) Pin Configuration
Table 7. E-20-1 Package Pin Function Descriptions
Pin No.
Mnemonic
Description
1, ꢂ, ꢀ, 7, ꢁ, 11, 13, 1ꢀ, 17, 19
2
3
6
NC
X1
X2
No Connect. Do not connect to this pin.
Noninverting Differential Input of the X Multiplicand Input.
Inverting Differential Input of the X Multiplicand Input.
Scale Factor Input.
SF
9
Y1
Y2
−VS
Z2
Z1
Noninverting Differential Input of the Y Multiplicand Input.
Inverting Differential Input of the Y Multiplicand Input.
Negative Supply Rail.
Inverting Differential Input of the Z Reference Input.
Noninverting Differential Input of the Z Reference Input.
Product Output.
10
12
1ꢂ
16
19
20
OUT
+VS
Positive Supply Rail.
Rev. C | Page 9 of 20
AD534
TYPICAL PERFORMANCE CHARACTERISTICS
Typical at 25°C, with ±±S = ±15 ± dc, unless otherwise noted.
14
1000
100
10
OUTPUT, R ≥ 2kΩ
L
12
10
8
ALL INPUTS, SF = 10V
X-FEEDTHROUGH
Y-FEEDTHROUGH
1
6
4
0.1
10
100
1k
10k
100k
1M
10M
8
10
12
14
16
18
20
FREQUENCY (Hz)
POSITIVE OR NEGATIVE SUPPLY (V)
Figure 7. Input/Output Signal Range vs. Supply Voltages
Figure 10. AC Feedthrough vs. Frequency
800
1.5
700
600
500
400
SCALING VOLTAGE = 10V
1
SCALING VOLTAGE = 10V
SCALING VOLTAGE = 3V
300
200
100
0
0.5
SCALING VOLTAGE = 3V
0
10
100
1k
10k
100k
–60 –40 –20
0
20
40
60
80
100 120 140
FREQUENCY (Hz)
TEMPERATURE (°C)
Figure 11. Noise Spectral Density vs. Frequency
Figure 8. Bias Current vs. Temperature (X, Y, or Z Input)
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
CONDITIONS:
10Hz TO 10kHz BANDWIDTH
TYPICAL FOR
ALL INPUTS
50
2.5
100
1k
10k
100k
1M
5.0
7.5
10.0
FREQUENCY (Hz)
SCALING VOLTAGE, SF (V)
Figure 9. Common-Mode Rejection Ratio vs. Frequency
Figure 12. Wideband Noise vs. Scaling Voltage
Rev. C | Page 10 of 20
AD534
10
0
60
40
0dB = 0.1V RMS, R = 2kΩ
L
V
V
= 100mV dc
= 10mV rms
X
Z
C
= 0pF
L
–10
20
0
V
V
= 1V dc
= 100mV rms
C
C
≤ 1000pF
= 0pF
C
L
≤ 1000pF
≤ 200pF
X
Z
L
F
C
F
–20
–30
NORMAL
CONNECTION
WITH ×10
FEEDBACK
ATTENUATOR
V
V
= 10V dc
= 1V rms
X
Z
–20
1k
100k
1M
10M
10k
10k
100k
FREQUENCY (Hz)
1M
10M
FREQUENCY (Hz)
Figure 14. Frequency Response vs. Divider Denominator Input Voltage
Figure 13. Frequency Response as a Multiplier
Rev. C | Page 11 of 20
AD534
FUNCTIONAL DESCRIPTION
inputs is now fully utilized. Bandwidth is unaffected by the use
of this option.
Figure 1 shows a functional block diagram of the AD534. Inputs
are converted to differential currents by three identical voltage-
to-current converters, each trimmed for zero offset. The product
of the X and Y currents is generated by a multiplier cell using
Gilbert’s translinear technique. An on-chip buried Zener
provides a highly stable reference, which is laser trimmed to
provide an overall scale factor of 10 ±. The difference between
XY/SF and Z is then applied to the high gain output amplifier.
This permits various closed-loop configurations and dramati-
cally reduces nonlinearities due to the input amplifiers, a
dominant source of distortion in earlier designs.
Supply voltages of ±15 ± are generally assumed. However,
satisfactory operation is possible down to ±8 ± (see Figure 7).
Because all inputs maintain a constant peak input capability of
±1.25 SF, some feedback attenuation is necessary to achieve
output voltage swings in excess of ±12 ± when using higher
supply voltages.
PROVIDES GAIN WITH LOW NOISE
The AD534 is the first general-purpose multiplier capable of
providing gains up to ×100, frequently eliminating the need for
separate instrumentation amplifiers to precondition the inputs.
The AD534 can be very effectively employed as a variable gain
differential input amplifier with high common-mode rejection.
The gain option is available in all modes and simplifies the
implementation of many function-fitting algorithms such as
those used to generate sine and tangent. The utility of this
feature is enhanced by the inherent low noise of the AD534:
90 μ± rms (depending on the gain), a factor of 10 lower than
previous monolithic multipliers. Drift and feedthrough are also
substantially reduced over earlier designs.
The effectiveness of the new scheme can be judged from the
fact that, under typical conditions as a multiplier, the nonlinear-
ity on the Y input, with X at full scale (±10 ±), is ±0.005ꢀ of FS.
Even at its worst point, which occurs when X = ±ꢁ.4 ±, nonlinear-
ity is typically only ±0.05ꢀ of FS. Nonlinearity for signals applied
to the X input, on the other hand, is determined almost entirely
by the multiplier element and is parabolic in form. This error is a
major factor in determining the overall accuracy of the unit and
therefore is closely related to the device grade.
The generalized transfer function for the AD534 is given by
(
X1 − X2 )(Y1 −Y2
)
OPERATION AS A MULTIPLIER
VOUT = A
−
(
Z1 − Z2
)
SF
Figure 15 shows the basic connection for multiplication. Note
that the circuit meets all specifications without trimming.
where:
A is the open-loop gain of the output amplifier, typically
70 dB at dc.
X1, Y1, Z1, X2, Y2, and Z2 are the input voltages (full scale = ±SF,
peak = ±1.25 SF).
SF is the scale factor, pretrimmed to 10.00 ± but adjustable by
the user down to 3 ±.
X
+V
+15V
1
S
X INPUT
±10V FS
±12V PK
OUTPUT, ±12V PK =
(X1 – X ) (Y1 – Y )
X
2
OUT
2
2
+ Z
AD534
2
10V
Z
Z
1
2
SF
OPTIONAL SUMMING
INPUT, Z, ±10V PK
Y
1
Y INPUT
±10V FS
±12V PK
–15V
Y
–V
2
S
In most cases, the open-loop gain can be regarded as infinite,
and SF is 10 ±. The operation performed by the AD534, can
then be described in terms of the following equation:
Figure 15. Basic Multiplier Connection
To reduce ac feedthrough to a minimum (as in a suppressed
carrier modulator), apply an external trim voltage (±30 m±
range required) to the X or Y input (see Figure 3). Figure 10
shows the typical ac feedthrough with this adjustment mode.
Note that the Y input is a factor of 10 lower than the X input
and should be used in applications where null suppression is
critical.
(X1 − X2)(Y1 −Y2 ) = 10 ± (Z1 − Z2)
The user can adjust SF for values between 10.00 ± and 3 ± by
connecting an external resistor in series with a potentiometer
between SF and −±S. The approximate value of the total
resistance for a given value of SF is given by the relationship:
SF
10 − SF
RS = 5.4kꢂ
The high impedance Z2 terminal of the AD534 can be used to
sum an additional signal into the output. In this mode, the
output amplifier behaves as a voltage follower with a 1 MHz
small signal bandwidth and a 20 ±/μs slew rate. This terminal
should always be referenced to the ground point of the driven
system, particularly if this is remote. Likewise, the differential
inputs should be referenced to their respective ground poten-
tials to realize the full accuracy of the AD534.
F
Due to device tolerances, allowance should be made to vary RSF
by ±25ꢀ using the potentiometer. Considerable reduction in
bias currents, noise, and drift can be achieved by decreasing SF.
This has the overall effect of increasing signal gain without the
customary increase in noise. Note that the peak input signal is
always limited to 1.25 SF (that is, ±5 ± for SF = 4 ±) so the
overall transfer function shows a maximum gain of 1.25. The
performance with small input signals, however, is improved by
using a lower scale factor because the dynamic range of the
A much lower scaling voltage can be achieved without any
reduction of input signal range using a feedback attenuator as
shown in Figure 1ꢁ. In this example, the scale is such that ±OUT
=
Rev. C | Page 12 of 20
AD534
(X1 – X2)(Y1 – Y2), so that the circuit can exhibit a maximum
gain of 10. This connection results in a reduction of bandwidth
to about 80 kHz without the peaking capacitor CF = 200 pF. In
addition, the output offset voltage is increased by a factor of 10
making external adjustments necessary in some applications.
Adjustment is made by connecting a 4.7 MΩ resistor between
Z1 and the slider of a potentiometer connected across the
supplies to provide ±300 m± of trim range at the output.
If the application depends on accurate operation for inputs that
are always less than ±3 ±, the use of a reduced value of SF is recom-
mended as described in the Functional Description section.
Alternatively, a feedback attenuator can be used to raise the
output level. This is put to use in the difference-of-squares
application to compensate for the factor of 2 loss involved in
generating the sum term (see Figure 20).
The difference of squares function is also used as the basis for a
novel rms-to-dc converter shown in Figure 27. The averaging
filter is a true integrator, and the loop seeks to zero its input. For
this to occur, (±IN)2 − (±OUT)2 = 0 ± (for signals whose period is
well below the averaging time constant). Therefore, ±OUT is
forced to equal the rms value of ±IN. The absolute accuracy of
this technique is very high; at medium frequencies and for
signals near full scale, it is determined almost entirely by the
ratio of the resistors in the inverting amplifier. The multiplier
scaling voltage affects only open-loop gain. The data shown is
typical of performance that can be achieved with an AD534K,
but even using an AD534J, this technique can readily provide
better than 1ꢀ accuracy over a wide frequency range, even for
crest factors in excess of 10.
X
+V
+15V
1
S
X INPUT
±10V FS
±12V PK
OUTPUT, ±12V PK =
(X – X ) (Y – Y )
X
2
OUT
1
2
1
2
(SCALE = 1V)
90kΩ
10kΩ
AD534
Z
SF
1
2
OPTIONAL PEAKING
CAPACITOR C = 200pF
F
Z
Y
1
Y INPUT
±10V FS
±12V PK
–15V
Y
2
–V
S
Figure 16. Connections for Scale Factor of Unity
Feedback attenuation also retains the capability for adding a
signal to the output. Signals can be applied to the high impedance
Z2 terminal where they are amplified by +10 or to the common
ground connection where they are amplified by +1. Input signals
can also be applied to the lower end of the 10 kΩ resistor, giving
a gain of −9. Other values of feedback ratio, up to ×100, can be
used to combine multiplication with gain.
OPERATION AS A DIVIDER
Figure 18 shows the connection required for division. Unlike
earlier products, the AD534 provides differential operation on
both numerator and denominator, allowing the ratio of two
floating variables to be generated. Further flexibility results
from access to a high impedance summing input to Y1. As with
all dividers based on the use of a multiplier in a feedback loop,
the bandwidth is proportional to the denominator magnitude,
as shown in Figure 14.
Occasionally, it may be desirable to convert the output to a
current into a load of unspecified impedance or dc level. For
example, the function of multiplication is sometimes followed
by integration; if the output is in the form of a current, a simple
capacitor provides the integration function. Figure 17 shows
how this can be achieved. This method can also be applied in
squaring, dividing, and square rooting modes by appropriate
choice of terminals. This technique is used in the voltage
controlled low-pass filter and the differential input voltage-to-
frequency converter shown in the Applications Information
section.
+
OUTPUT, ±12V PK =
10V (Z – Z )
X INPUT
(DENOMINATOR)
±10V FS
X
+V
+15V
1
S
2
1
+ Y
1
(X – X )
1
2
X
±12V PK
2
OUT
–
AD534
Z INPUT
(NUMERATOR)
±10V FS
Z
Z
SF
1
2
OPTIONAL
SUMMING
INPUT
X
+V
S
1
X INPUT
±10V FS
±12V PK
CURRENT-SENSING
RESISTOR, RS, 2kΩ MIN
±12V PK
Y
1
X
2
±10V PK
OUT
–15V
Y
–V
2
S
AD534
Z
Z
SF
1
2
(X – X ) (Y – Y )
1
RS
1
2
1
2
I
=
×
OUT
10V
Figure 18. Basic Divider Connection
Y
1
Y INPUT
±10V FS
±12V PK
INTEGRATOR
CAPACITOR
(SEE TEXT)
Without additional trimming, the accuracy of the AD534K and
AD534L is sufficient to maintain a 1ꢀ error over a 10 ± to 1 ±
denominator range. This range can be extended to 100:1 by
simply reducing the X offset with an externally generated trim
voltage (range required is ±3.5 m± maximum) applied to the
unused X input (see Figure 3). To trim, apply a ramp of +100 m±
to +± at 100 Hz to both X1 and Z1 (if X2 is used for offset adjust-
ment; otherwise, reverse the signal polarity) and adjust the trim
voltage to minimize the variation in the output
Y
–V
2
S
Figure 17. Conversion of Output to Current
OPERATION AS A SQUARER
Operation as a squarer is achieved in the same fashion as the
multiplier except that the X and Y inputs are used in parallel.
The differential inputs can be used to determine the output
polarity (positive for X1 = Yl and X2 = Y2, negative if either one
of the inputs is reversed). Accuracy in the squaring mode is
typically a factor of 2 better than in the multiplying mode and
the largest errors occurring with small values of output for
input below 1 ±.
Because the output is near 10 ±, it should be ac-coupled for
this adjustment. The increase in noise level and reduction in
bandwidth preclude operation much beyond a ratio of 100 to 1.
Rev. C | Page 13 of 20
AD534
As with the multiplier connection, overall gain can be introduced
by inserting a simple attenuator between the output and Y2
terminal. This option and the differential ratio capability of the
AD534 are used in the percentage computer application shown
in Figure 24. This configuration generates an output propor-
tional to the percentage deviation of one variable (A) with
respect to a reference variable (B), with a scale of 1ꢀ per volt.
In contrast to earlier devices, which were intolerant of capacitive
loads in the square root modes, the AD534 is stable with all
loads up to at least 1000 pF. For critical applications, a small
adjustment to the Z input offset (see Figure 3) improves
accuracy for inputs below 1 ±.
UNPRECEDENTED FLEXIBILITY
The precise calibration and differential Z input provide a degree
of flexibility found in no other currently available multiplier.
Standard multiplication, division, squaring, square-rooting
(MDSSR) functions are easily implemented while the restriction
to particular input/output polarities imposed by earlier designs
has been eliminated. Signals can be summed into the output,
with or without gain and with either a positive or negative
sense. Many new modes based on implicit function synthesis
have been made possible, usually requiring only external
passive components. The output can be in the form of a current,
if desired, facilitating such operations as integration.
OPERATION AS A SQUARE ROOTER
The operation of the AD534 in the square root mode is shown
in Figure 19. The diode prevents a latching condition, which
may occur if the input momentarily changes polarity. As shown,
the output is always positive; it can be changed to a negative
output by reversing the diode direction and interchanging the X
inputs. Because the signal input is differential, all combinations
of input and output polarities can be realized, but operation is
restricted to the one quadrant associated with each combination
of inputs.
OUTPUT, ±12V PK =
10V (Z – Z ) + X
2
2
1
R
L
REVERSE THIS
AND X INPUTS
FOR NEGATIVE
OUTPUTS
X
X
+V
+15V
(MUST BE
PROVIDED)
1
S
2
OUT
AD534
OPTIONAL
SUMMING
INPUT
–
+
Z
Z INPUT
±10V FS
±12V PK
SF
1
2
Z
X, ±10V PK
Y
Y
1
–15V
–V
2
S
Figure 19. Square-Rooter Connection
Rev. C | Page 1ꢂ of 20
AD534
APPLICATIONS INFORMATION
The versatility of the AD534 allows the creative designer to implement a variety of circuits such as wattmeters, frequency doublers, and
automatic gain controls.
X
+V
+15V
1
S
MODULATION
INPUT, ±E
M
E
M
X
2
OUT
OUTPUT = 1 ±
E sin ωt
C
10V
AD534
X
X
+V
+15V
A
B
1
S
Z
SF
A – B
2
1
2
2
2
A
– B
10V
OUTPUT =
2
Z
OUT
CARRIER INPUT
sin ωt
Y
1
E
30kΩ
10kΩ
C
AD534
Z
SF
1
2
–15V
Y
–V
2
S
Z
Y
Y
1
A + B
2
THE SF PIN OR A Z ATTENUATOR CAN BE USED TO PROVIDE OVERALL
SIGNAL AMPLIFICATION. OPERATION FROM A SINGLE SUPPLY POSSIBLE;
–15V
–V
2
S
BIAS Y TO V /2.
2
S
Figure 23. Linear AM Modulator
Figure 20. Difference of Squares
X
+V
+15V
1
2
S
CONTROL INPUT,
, 0V TO ±5V
E
E
E
S
C
C
X
OUTPUT, ±12V PK =
0.005µF
OUT
0.1V
SET GAIN
1kΩ
39kΩ
1kΩ
AD534
X
X
+V
+15V
1
2
S
2kΩ
9kΩ
1kΩ
Z
–V
SF
1
2
S
A – B
B
OUTPUT = (100V)
(1% PER VOLT)
OUT
Z
Y
1
AD534
SIGNAL INPUT,
Z
E , ±5V PK
SF
1
2
S
–15V
Y
–V
2
S
A INPUT (±)
Z
NOTES
1. GAIN IS × 10 PER VOLT OF E , ZERO TO × 50.
B INPUT,
(+V ONLY)
Y
Y
1
2
C
E
2. WIDEBAND (10Hz TO 30kHz) OUTPUT NOISE IS 3mV rms,
TYP CORRESPONDING TO A.F.S. SNR OF 70dB.
–15V
–V
S
3. NOISE REFERRED TO SIGNAL INPUT, WITH E = ±5V, IS
C
60µV rms, TYP.
OTHER SCALES, FROM 10% PER VOLT TO 0.1% PER VOLT
CAN BE OBTAINED BY ALTERING THE FEEDBACK RATIO.
4. BANDWIDTH IS DC TO 20kHz, –3dB, INDEPENDENT OF GAIN.
Figure 24. Percentage Computer
Figure 21. Voltage-Controlled Amplifier
X
X
+V
+15V
1
2
S
OUT
OUTPUT = (10V) sin θ
X
X
+V
+15V
1
S
18kΩ
4.7kΩ
4.3kΩ
E
θ
π
AD534
WHERE θ =
×
Z
10kΩ
10V
SF
1
2
2
OUTPUT, ±5V/PK =
y
2
OUT
INPUT, E
θ
AD534
Z
(10V)
Y
Y
1
2
1 + y
WHERE y =
0V TO +10V
Z
Z
SF
3kΩ
1
2
Y
(10V)
–15V
–V
S
Y
1
INPUT, Y ±10V FS
–15V
USING CLOSE TOLERANCE RESISTORS AND AD543L,
ACCURACY OF FIT IS WITHIN ±0.5% AT ALL POINTS.
θ IS IN RADIANS.
Y
–V
2
S
Figure 22. Sine Function Generator
Figure 25. Bridge Linearization Function
Rev. C | Page 1ꢀ of 20
AD534
+15V
2kΩ
ADJ 8kHz
39kΩ
X
X
+V
+15V
3pF to 30pF
2
1
S
82kΩ
2
OUT
ADJ
1kHz
7
OUTPUT
±15V APPROX.
AD534
3
Z
1
SF
500Ω 2.2kΩ
AD211
(= R)
PINS 5, 6, 8 TO +15V
PINS 1, 4 TO –15V
Z
2
+
–
Y
Y
1
0.01
(= C)
CONTROL INPUT,
100mV TO 10V
E
1
CR
C
f =
×
= 1kHz PER VOLT
E
C
40
–15V
–V
2
S
WITH VALUES SHOWN
CALIBRATION PROCEDURE:
WITH E = 1.0V, ADJUST POTENTIOMETER TO SET f = 1.000kHz WITH
C
E
= 8.0V, ADJUST TRIMMER CAPACITOR TO SET f = 8.000kHz. LINEARITY
C
WILL TYPICALLY BE WITHIN ±0.1% OF FS FORANY OTHER INPUT.
DUE TO DELAYS IN THE COMPARATOR, THIS TECHNIQUE IS NOT SUITABLE
FOR MAXIMUM FREQUENCIES ABOVE 10kHz. FOR FREQUENCIES ABOVE
10kHz THE AD537 VOLTAGE-TO-FREQUENCY CONVERTER IS RECOMMENDED.
A TRIANGLE-WAVE OF ±5V PK APPEARS ACROSS THE 0.01µF CAPACITOR: IF
USED AS AN OUTPUT, A VOLTAGE-FOLLOWER SHOULD BE INTERPOSED.
Figure 26. Differential Input Voltage-to-Frequency Converter
MATCHED TO 0.025%
20kΩ
10kΩ
10kΩ
AD741K
5kΩ
X
X
+V
+15V
10kΩ
1
S
10µF
NONPOLAR
INPUT
5V RMS FS
±10V PEAK
+
OUT
2
10µF SOLID Ta
RMS + DC
MODE
AC RMS
AD534
SF
10kΩ
OUTPUT
0V TO 5V
Z
Z
1
10kΩ
2
AD741J
+15V
Y
Y
1
10MΩ
–V
S
2
ZERO
ADJ
–15V
20kΩ
CALIBRATION PROCEDURE:
WITH MODE SWITCH IN ‘RMS + DC’ POSITION, APPLY AN INPUT OF +1.00V DC.
ADJUST ZERO UNTIL OUTPUT READS SAME AS INPUT. CHECK FOR INPUTS
OF ±10V; OUTPUT SHOULD BE WITHIN ±0.05% (5mV).
ACCURACY IS MAINTAINED FROM 60Hz TO 100kHz, AND IS TYPICALLY HIGH
BY 0.5% AT 1MHz FOR V = 4V RMS (SINE, SQUARE, OR TRIANGLULAR-WAVE).
IN
PROVIDED THAT THE PEAK INPUT IS NOT EXCEEDED, CREST FACTORS UP
TO AT LEAST 10 HAVE NO APPRECIABLE EFFECT ON ACCURACY.
INPUT IMPEDANCE IS ABOUT 10kΩ; FOR HIGH (10MΩ) IMPEDANCE, REMOVE
MODE SWITCH AND INPUT COUPLING COMPONENTS.
FOR GUARANTEED SPECIFICATIONS THE AD536A AND AD636 ARE OFFERED
AS A SINGLE PACKAGE RMS-TO-DC CONVERTER.
Figure 27. Wideband, High-Crest Factor, RMS-to-DC Converter
Rev. C | Page 16 of 20
AD534
OUTLINE DIMENSIONS
REFERENCE PLANE
0.500 (12.70)
MIN
0.160 (4.06)
0.110 (2.79)
0.185 (4.70)
0.165 (4.19)
6
7
5
8
0.021 (0.53)
0.016 (0.40)
0.115
(2.92)
BSC
4
0.045 (1.14)
0.025 (0.65)
9
3
10
0.034 (0.86)
0.025 (0.64)
2
1
0.230 (5.84)
BSC
BASE & SEATING PLANE
0.040 (1.02) MAX
0.050 (1.27) MAX
36° BSC
DIMENSIONS PER JEDEC STANDARDS MO-006-AF
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 28. 10-Pin Metal Header Package [TO-100]
(H-10)
Dimensions shown in inches and (millimeters)
0.005 (0.13) MIN
0.080 (2.03) MAX
8
14
0.310 (7.87)
1
0.220 (5.59)
7
PIN 1
0.100 (2.54)
BSC
0.320 (8.13)
0.290 (7.37)
0.765 (19.43) MAX
0.060 (1.52)
0.015 (0.38)
0.200 (5.08)
MAX
0.150
(3.81)
MIN
0.200 (5.08)
0.125 (3.18)
0.015 (0.38)
0.008 (0.20)
SEATING
PLANE
0.070 (1.78)
0.030 (0.76)
0.023 (0.58)
0.014 (0.36)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 29. 14-Lead Side-Brazed Ceramic Dual In-Line Package [SBDIP]
(D-14)
Dimensions shown in inches and (millimeters)
0.200 (5.08)
0.075 (1.91)
REF
REF
0.100 (2.54)
0.064 (1.63)
0.100 (2.54) REF
0.095 (2.41)
0.015 (0.38)
MIN
0.075 (1.90)
3
19
18
20
4
8
0.028 (0.71)
0.022 (0.56)
1
0.358 (9.09)
0.342 (8.69)
SQ
0.358
0.011 (0.28)
0.007 (0.18)
R TYP
(9.09)
MAX
SQ
BOTTOM
VIEW
0.050 (1.27)
BSC
14
0.075 (1.91)
13
9
REF
45° TYP
0.088 (2.24)
0.054 (1.37)
0.055 (1.40)
0.045 (1.14)
0.150 (3.81)
BSC
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 30. 20-Terminal Ceramic Leadless Chip Carrier [LCC]
(E-20-1)
Dimensions shown in inches and (millimeters)
Rev. C | Page 17 of 20
AD534
ORDERING GUIDE
Model1
Temperature Range
Package Description
Package Option
D-1ꢂ
D-1ꢂ
D-1ꢂ
D-1ꢂ
D-1ꢂ
D-1ꢂ
H-10
H-10
H-10
H-10
H-10
H-10
ADꢀ3ꢂJD
0°C to +70°C
1ꢂ-Lead Side Brazed Ceramic Dual In-Line Package [SBDIP]
1ꢂ-Lead Side Brazed Ceramic Dual In-Line Package [SBDIP]
1ꢂ-Lead Side Brazed Ceramic Dual In-Line Package [SBDIP]
1ꢂ-Lead Side Brazed Ceramic Dual In-Line Package [SBDIP]
1ꢂ-Lead Side Brazed Ceramic Dual In-Line Package [SBDIP]
1ꢂ-Lead Side Brazed Ceramic Dual In-Line Package [SBDIP]
10-Pin Metal Header Package [TO-100]
10-Pin Metal Header Package [TO-100]
10-Pin Metal Header Package [TO-100]
10-Pin Metal Header Package [TO-100]
10-Pin Metal Header Package [TO-100]
10-Pin Metal Header Package [TO-100]
Chip
1ꢂ-Lead Side Brazed Ceramic Dual In-Line Package [SBDIP]
1ꢂ-Lead Side Brazed Ceramic Dual In-Line Package [SBDIP]
1ꢂ-Lead Side Brazed Ceramic Dual In-Line Package [SBDIP]
1ꢂ-Lead Side Brazed Ceramic Dual In-Line Package [SBDIP]
20-Terminal Ceramic Leadless Chip Carrier [LCC]
20-Terminal Ceramic Leadless Chip Carrier [LCC]
10-Pin Metal Header Package [TO-100]
10-Pin Metal Header Package [TO-100]
10-Pin Metal Header Package [TO-100]
10-Pin Metal Header Package [TO-100]
Chip
ADꢀ3ꢂJDZ
ADꢀ3ꢂKD
0°C to +70°C
0°C to +70°C
ADꢀ3ꢂKDZ
ADꢀ3ꢂLD
0°C to +70°C
0°C to +70°C
ADꢀ3ꢂLDZ
ADꢀ3ꢂJH
0°C to +70°C
0°C to +70°C
ADꢀ3ꢂJHZ
ADꢀ3ꢂKH
0° C to +70°C
0°C to +70°C
ADꢀ3ꢂKHZ
ADꢀ3ꢂLH
0°C to +70°C
0°C to +70°C
ADꢀ3ꢂLHZ
ADꢀ3ꢂK Chips
ADꢀ3ꢂSD
ADꢀ3ꢂSD/ꢁꢁ3B
ADꢀ3ꢂTD
ADꢀ3ꢂTD/ꢁꢁ3B
ADꢀ3ꢂSE/ꢁꢁ3B
ADꢀ3ꢂTE/ꢁꢁ3B
ADꢀ3ꢂSH
ADꢀ3ꢂSH/ꢁꢁ3B
ADꢀ3ꢂTH
0°C to +70°C
0°C to +70°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
−ꢀꢀ°C to +12ꢀ°C
D-1ꢂ
D-1ꢂ
D-1ꢂ
D-1ꢂ
E-20-1
E-20-1
H-10
H-10
H-10
H-10
ADꢀ3ꢂTH/ꢁꢁ3B
ADꢀ3ꢂS Chips
ADꢀ3ꢂT Chips
Chip
1 Z = RoHS Compliant Part.
Rev. C | Page 1ꢁ of 20
AD534
NOTES
Rev. C | Page 19 of 20
AD534
NOTES
©1977–2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09675-0-4/11(C)
Rev. C | Page 20 of 20
©2020 ICPDF网 联系我们和版权申明