SSM2380 [ADI]
Filterless, Stereo, Class-D Audio Amplifier;
| 型号： | SSM2380 |
| 厂家： | 
ADI |
| 描述： | Filterless, Stereo, Class-D Audio Amplifier |
| 文件： | 总32页 (文件大小：691K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
2 × 2 W, Filterless, Stereo, Class-D
Audio Amplifier with ALC and I2C
SSM2380
The SSM2380 features a high efficiency, low noise modulation
scheme that requires no external LC output filters. The modulation
continues to provide high efficiency even at low output power.
The SSM2380 operates with 93% efficiency at 1.4 W into 8 Ω
or with 85% efficiency at 2 W into 4 Ω from a 5.0 V supply and
has an SNR of >100 dB.
FEATURES
Filterless, stereo, Class-D amplifier with Σ-Δ modulation
2 W into 4 Ω load and 1.4 W into 8 Ω load at 5.0 V supply
with <1% total harmonic distortion plus noise (THD + N)
Highly configurable I2C interface for gain adjust, automatic
level control (ALC), and ultralow EMI emissions mode
MODE pin can disable I2C interface for more traditional
stereo amplifier configuration
Stereo-to-mono mixer option via I2C control
93% efficiency at 5.0 V, 1.4 W into 8 Ω speaker
Signal-to-noise ratio (SNR): >100 dB
Single-supply operation from 2.5 V to 5.5 V
Ultralow shutdown current: 20 nA
Short-circuit and thermal protection
Pop-and-click suppression
Available in 16-ball, 2.0 mm × 2.0 mm WLCSP
Spread-spectrum pulse density modulation is used to provide
lower EMI-radiated emissions compared with other Class-D
architectures. An added benefit of spread-spectrum Σ-Δ modu-
lation is that no synchronization (SYNC) is needed when using
multiple Class-D amplifiers. For applications that require long
speaker cables (>10 cm), the SSM2380 includes a user-selectable
ultralow EMI emissions mode that eliminates the need for EMI
filters at the Class-D outputs.
The SSM2380 has a micropower shutdown mode with a typical
shutdown current of 20 nA. Shutdown is enabled by applying
SD
a logic low to the
pin or through an optional independent
APPLICATIONS
channel soft shutdown via I2C.
Mobile phones
MP3 players
Portable electronics
The device also includes pop-and-click suppression circuitry.
This suppression circuitry minimizes voltage glitches at the
output during turn-on and turn-off, reducing audible noise
on activation and deactivation.
GENERAL DESCRIPTION
The SSM2380 is a fully integrated, high efficiency, stereo, Class-D
audio amplifier. It is designed to maximize performance for mobile
phone applications. The application circuit requires a minimum
of external components and operates from a single 2.5 V to 5.5 V
supply. It is capable of delivering 2 W of continuous output power
with <1% THD + N driving a 4 Ω load from a 5.0 V supply.
The SSM2380 features a highly flexible I2C interface with many
useful settings. Using the I2C control interface, the gain of the
SSM2380 can be selected from 1 dB to 24 dB (plus mute) in
47 steps with no external components. Other features accessed
from the I2C interface include independent left/right channel
shutdown, variable ultralow EMI emission control mode, auto-
matic level control (ALC) for high quality speaker protection,
and stereo-to-mono mixing operation.
The fully differential inputs of the SSM2380 provide excellent
rejection of common-mode noise on the input. Input coupling
capacitors can be omitted if the dc input common-mode voltage
is approximately VDD/2.
The SSM2380 is specified over the commercial temperature
range of −40°C to +85°C. It has built-in thermal shutdown
and output short-circuit protection. It is available in a 16-ball,
2 mm × 2 mm wafer level chip scale package (WLCSP).
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2010–2011 Analog Devices, Inc. All rights reserved.
SSM2380
TABLE OF CONTENTS
Features .............................................................................................. 1
Mixer Mode................................................................................. 18
Applications Information.............................................................. 19
Layout .......................................................................................... 19
Input Capacitor Selection.......................................................... 19
Power Supply Decoupling ......................................................... 20
Typical Application Circuits ......................................................... 21
I2C Interface .................................................................................... 24
Register Map ................................................................................... 25
Register Map Details ...................................................................... 26
Register R0: Left Channel Gain Control, Address 0x00........ 26
Register R1: Right Channel Gain Control, Address 0x01..... 26
Register R2: Mode Control, Address 0x02.............................. 27
Register R3: ALC Control 1, Address 0x03............................. 27
Register R4: ALC Control 2, Address 0x04............................. 28
Register R5: Shutdown, Address 0x05..................................... 29
Register R6: Error, Address 0x06.............................................. 29
Register R7: Error Clear, Address 0x07................................... 29
Register R8: Reset, Address 0x08 ............................................. 29
Outline Dimensions....................................................................... 30
Ordering Guide .......................................................................... 30
Applications....................................................................................... 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Functional Block Diagram .............................................................. 3
Specifications..................................................................................... 4
I2C Timing Characteristics.......................................................... 5
Absolute Maximum Ratings............................................................ 6
Thermal Resistance ...................................................................... 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 8
Theory of Operation ...................................................................... 14
Overview...................................................................................... 14
Pop-and-Click Suppression....................................................... 14
Output Modulation Description .............................................. 14
Operating Modes........................................................................ 15
ALC Mode Operation................................................................ 15
Gain Select Mode Operation .................................................... 16
I2C Control Mode Operation.................................................... 16
Automatic Level Control (ALC)............................................... 16
REVISION HISTORY
2/11—Rev. 0 to Rev. A
Changes to Setting the ALC Threshold Voltage Section........... 15
10/10—Revision 0: Initial Version
Rev. A | Page 2 of 32
SSM2380
FUNCTIONAL BLOCK DIAGRAM
10µF
VDD 2.5V TO 5.5V
0.1µF
VDD
SSM2380
VDD
FET
22nF
INR+
OUTR+
OUTR–
RIGHT IN+
Σ-∆
MODULATOR
INR–
DRIVER
RIGHT IN–
22nF
SCK
SDA
MODE
GAIN
CONTROL
(+ALC)
EDGE
SD
2
I C
INTERNAL
EMI
EMISSION CONTROL
SHUTDOWN
BIAS
OSCILLATOR CONTROL
22nF
22nF
INL+
INL–
OUTL+
OUTL–
LEFT IN+
LEFT IN–
Σ-∆
FET
DRIVER
MODULATOR
GND
GND
GAIN1
GAIN0
ALCTH
GAIN = 6dB, 12dB, 18dB, OR 24dB
Figure 1.
Rev. A | Page 3 of 32
SSM2380
SPECIFICATIONS
VDD = 5.0 V, TA = 25°C, RL = 8 Ω +33 μH, gain = 6 dB, I2C control mode, unless otherwise noted.
Table 1.
Parameter
Symbol
Test Conditions/Comments1
f = 1 kHz, 20 kHz bandwidth
RL = 8 Ω, THD = 1%, VDD = 5.0 V
RL = 8 Ω, THD = 1%, VDD = 3.6 V
RL = 8 Ω, THD = 10%, VDD = 5.0 V
RL = 8 Ω, THD = 10%, VDD = 3.6 V
RL = 4 Ω, THD = 1%, VDD = 5.0 V
RL = 4 Ω, THD = 1%, VDD = 3.6 V
RL = 4 Ω, THD = 10%, VDD = 5.0 V
RL = 4 Ω, THD = 10%, VDD = 3.6 V
PO = 1.4 W into 8 Ω, VDD = 5.0 V
Normal, low EMI mode
Min
Typ
Max
Unit
DEVICE CHARACTERISTICS
Output Power
PO
1.43
0.73
1.8
0.92
2.581
1.3
W
W
W
W
W
W
W
W
3.21
1.62
Efficiency
η
93
91
0.005
%
%
%
Ultralow EMI mode
Total Harmonic Distortion Plus
Noise
THD + N PO = 1 W into 8 Ω, f = 1 kHz, VDD = 5.0 V
PO = 0.5 W into 8 Ω, f = 1 kHz, VDD = 3.6 V
VCM
0.005
%
V
Input Common-Mode Voltage
Range
1.0
VDD − 1.0
Common-Mode Rejection Ratio
Channel Separation
Average Switching Frequency
Differential Output Offset
Voltage
CMRRGSM VCM = 2.5 V 100 mV at 217 Hz, output referred
55
78
325
2.0
dB
dB
kHz
mV
XTALK
fSW
PO = 100 mW, f = 1 kHz
VOOS
Gain = 6 dB
POWER SUPPLY
Supply Voltage Range
Power Supply Rejection Ratio
VDD
PSRR
PSRRGSM
Guaranteed from PSRR test
VDD = 2.5 V to 5.0 V, dc input floating
VRIPPLE = 100 mV at 217 Hz, inputs ac-grounded,
CIN = 0.1 μF
2.5
70
5.5
V
dB
dB
85
60
Supply Current, Stereo
ISY
VIN = 0 V, no load, VDD = 5.0 V
VIN = 0 V, no load, VDD = 3.6 V
VIN = 0 V, no load, VDD = 2.5 V
VIN = 0 V, RL = 8 Ω + 33 μH, VDD = 5.0 V
VIN = 0 V, RL = 8 Ω + 33 μH, VDD = 3.6 V
VIN = 0 V, RL = 8 Ω + 33 μH, VDD = 2.5 V
SD = GND
6.8
6.0
5.8
7.0
6.1
5.5
20
mA
mA
mA
mA
mA
mA
nA
Shutdown Current
ISD
GAIN CONTROL
Closed-Loop Gain
SHUTDOWN CONTROL
Input Voltage High
Input Voltage Low
Turn-On Time
Gain
GAINx = I2C control mode
1
24
dB
VIH
VIL
tWU
tSD
1.35
V
0.35
V
SD rising edge from GND to VDD
SD falling edge from VDD to GND
SD = GND
7
ms
μs
kΩ
Turn-Off Time
5
Output Impedance
ZOUT
>100
NOISE PERFORMANCE
Output Voltage Noise
en
VDD = 3.6 V, f = 20 Hz to 20 kHz, inputs are
ac-grounded, gain = 6 dB, A-weighted
30
μV rms
Signal-to-Noise Ratio
SNR
PO = 1.4 W, RL = 8 Ω, gain = 6 dB
PO = 1.4 W, RL = 8 Ω, gain = 24 dB
100
90
dB
dB
1 Although the SSM2380 has good quality above 2 W, continuous output power beyond 2 W must be avoided due to device packaging limitations.
Rev. A | Page 4 of 32
SSM2380
I2C TIMING CHARACTERISTICS
Table 2.
Limit
Parameter
Unit
ns
ns
ns
ꢀs
kHz
ns
ns
ns
ns
Description
tMIN
600
600
600
1.3
0
tMAX
tSCS
tSCH
tPH
tPL
fSCK
tDS
tDH
tRT
Start condition setup time
Start condition hold time
SCK pulse width high
SCK pulse width low
SCK frequency
Data setup time
Data hold time
SDA and SCK rise time
SDA and SCK fall time
Stop condition setup time
526
100
900
300
300
tFT
tHCS
600
ns
Timing Diagram
tSCH
tHCS
SDA
tDS
tSCS
tPH
tPL
SCK
tRT
tDH
tFT
Figure 2. I2C Timing
Rev. A | Page 5 of 32
SSM2380
ABSOLUTE MAXIMUM RATINGS
Absolute maximum ratings apply at 25°C, unless otherwise noted.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3.
Parameter
Rating
Supply Voltage
Input Voltage
Common-Mode Input Voltage
ESD Susceptibility
6 V
VDD
VDD
4 kV
Table 4. Thermal Resistance
Package Type
16-Lead, 2.0 mm × 2.0 mm WLCSP
PCB
θJA
θJB
Unit
2S2P 57
14
°C/W
Storage Temperature Range
Operating Temperature Range
Junction Temperature Range
Lead Temperature
(Soldering, 60 sec)
−65°C to +150°C
−40°C to +85°C
−65°C to +165°C
300°C
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. A | Page 6 of 32
SSM2380
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
BALL A1
INDICATOR
1
2
3
4
OUTL+
VDD
VDD
OUTR+
A
B
OUTL–
GND
GND
OUTR–
SDA
ALCTH
GAIN1
SCK
EDGE
GAIN0
SD
MODE
INL–
C
D
INL+
INR–
INR+
TOP VIEW
(BALL SIDE DOWN)
Not to Scale
Figure 3. Pin Configuration (Bottom View)
Table 5. Pin Function Descriptions
Pin No.
Mnemonic
OUTL+
VDD
OUTR+
OUTL−
GND
Description
A1
A2, A3
A4
B1
B2, B3
B4
Noninverting Output for Left Channel.
Power Supply for Output Amplifiers.
Noninverting Output for Right Channel.
Inverting Output for Left Channel.
Ground for Output Amplifiers.
OUTR−
SD
Inverting Output for Right Channel.
Shutdown Input. Active low digital input.
C1
C2
C3
MODE
SCK/EDGE/GAIN0
Three-Mode Interface Control Pin.
2-Wire I2C Control Interface Clock Input (SCK). MODE is connected to GND.
Low Emissions Mode Enable Pin (EDGE). MODE is floating.
Gain Select Pin, LSB (GAIN0). MODE is connected to VDD.
C4
SDA/ALCTH/GAIN1 2-Wire I2C Control Interface Data Input/Output (SDA). MODE is connected to GND.
Variable Threshold Voltage for ALC (ALCTH). MODE is floating.
Gain Select Pin, MSB (GAIN1). MODE is connected to VDD.
D1
D2
D3
D4
INL+
INL−
INR−
INR+
Noninverting Input for Left Channel.
Inverting Input for Left Channel.
Inverting Input for Right Channel.
Noninverting Input for Right Channel.
Rev. A | Page 7 of 32
SSM2380
TYPICAL PERFORMANCE CHARACTERISTICS
EDGE pin = GND, unless otherwise noted.
100
100
10
1
R
= 8Ω + 33µH
R = 8Ω + 33µH
L
GAIN = 24dB
L
GAIN = 6dB
V
= 2.5V
V
= 2.5V
DD
DD
10
1
V
= 3.6V
V
= 3.6V
DD
DD
V
= 5V
V
= 5V
DD
DD
0.1
0.1
0.01
0.01
0.001
0.0001
0.001
0.0001
0.001
0.01
0.1
1
10
0.001
0.01
0.1
1
10
OUTPUT POWER (W)
OUTPUT POWER (W)
Figure 4. THD + N vs. Output Power into 8 Ω, Gain = 6 dB
Figure 7. THD + N vs. Output Power into 8 Ω, Gain = 24 dB
100
10
1
100
10
1
R
= 4Ω + 15µH
R = 4Ω + 15µH
L
GAIN = 24dB
L
GAIN = 6dB
V
= 2.5V
DD
V
= 2.5V
DD
V
= 3.6V
V
= 3.6V
DD
DD
V
= 5V
V
= 5V
DD
DD
0.1
0.1
0.01
0.01
0.001
0.0001
0.001
0.0001
0.001
0.01
0.1
1
10
0.001
0.01
0.1
1
10
OUTPUT POWER (W)
OUTPUT POWER (W)
Figure 5. THD + N vs. Output Power into 4 Ω, Gain = 6 dB
Figure 8. THD + N vs. Output Power into 4 Ω, Gain = 24 dB
100
10
100
10
1
V
R
= 5V
= 8Ω + 33µH
V
R
= 5V
DD
= 8Ω + 33µH
L
DD
L
GAIN = 6dB
GAIN = 24dB
1
1W
0.1
1W
0.5W
0.1
0.01
0.001
0.0001
0.5W
0.01
0.25W
0.25W
100
0.001
10
100
1k
10k
100k
10
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 6. THD + N vs. Frequency, VDD = 5 V, RL = 8 Ω, Gain = 6 dB
Figure 9. THD + N vs. Frequency, VDD = 5 V, RL = 8 Ω, Gain = 24 dB
Rev. A | Page 8 of 32
SSM2380
100
10
1
100
10
1
V
R
= 5V
= 4Ω + 15µH
V
R
= 5V
DD
= 4Ω + 15µH
L
DD
L
GAIN = 6dB
GAIN = 24dB
2W
2W
0.1
0.1
1W
1W
0.01
0.01
0.5W
0.5W
0.001
0.001
10
100
1k
FREQUENCY (Hz)
10k
100k
10
100
1k
FREQUENCY (Hz)
10k
100k
Figure 10. THD + N vs. Frequency, VDD = 5 V, RL = 4 Ω, Gain = 6 dB
Figure 13. THD + N vs. Frequency, VDD = 5 V, RL = 4 Ω, Gain = 24 dB
100
100
V
= 3.6V
V
= 3.6V
DD
DD
R
= 8Ω + 33µH
R
= 8Ω + 33µH
L
L
GAIN = 6dB
GAIN = 24dB
10
1
10
1
0.5W
0.5W
0.1
0.1
0.25W
0.25W
0.01
0.01
0.125W
100
0.125W
1k
0.001
0.001
10
100
10k
100k
10
1k
FREQUENCY (Hz)
10k
100k
FREQUENCY (Hz)
Figure 11. THD + N vs. Frequency, VDD = 3.6 V, RL = 8 Ω, Gain = 6 dB
Figure 14. THD + N vs. Frequency, VDD = 3.6 V, RL = 8 Ω, Gain = 24 dB
100
100
V
= 3.6V
V
= 3.6V
DD
DD
R
= 4Ω + 15µH
R
= 4Ω + 15µH
L
L
GAIN = 6dB
GAIN = 24dB
10
1
10
1
1W
1W
0.1
0.1
0.5W
0.5W
0.01
0.01
0.25W
1k
0.25W
0.001
0.001
10
100
1k
10k
100k
10
100
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 12. THD + N vs. Frequency, VDD = 3.6 V, RL = 4 Ω, Gain = 6 dB
Figure 15. THD + N vs. Frequency, VDD = 3.6 V, RL = 4 Ω, Gain = 24 dB
Rev. A | Page 9 of 32
SSM2380
100
100
10
1
V
R
= 2.5V
= 8Ω + 33µH
V
R
= 2.5V
DD
= 8Ω + 33µH
L
DD
L
GAIN = 6dB
GAIN = 24dB
10
1
0.25W
0.25W
0.1
0.1
0.125W
0.125W
0.01
0.01
0.0625W
100
0.0625W
1k
0.001
0.001
10
100
10k
100k
10
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 16. THD + N vs. Frequency, VDD = 2.5 V, RL = 8 Ω, Gain = 6 dB
Figure 19. THD + N vs. Frequency, VDD = 2.5 V, RL = 8 Ω, Gain = 24 dB
100
100
V
= 2.5V
V
= 2.5V
DD
DD
R
= 4Ω + 15µH
R
= 4Ω + 15µH
L
L
GAIN = 6dB
GAIN = 24dB
10
1
10
1
0.5W
0.5W
0.1
0.1
0.25W
0.25W
0.01
0.01
0.125W
0.125W
0.001
0.001
10
100
1k
FREQUENCY (Hz)
10k
100k
10
100
1k
FREQUENCY (Hz)
10k
100k
Figure 17. THD + N vs. Frequency, VDD = 2.5 V, RL = 4 Ω, Gain = 6 dB
Figure 20. THD + N vs. Frequency, VDD = 2.5 V, RL = 4 Ω, Gain = 24 dB
7.5
7.0
BOTH CHANNELS
BOTH CHANNELS
GAIN = 6dB
7.0
GAIN = 24dB
6.5
R
= 4Ω + 15µH
L
6.5
6.0
5.5
5.0
4.5
4.0
R
= 4Ω + 15µH
L
6.0
5.5
5.0
R
= 8Ω + 33µH
L
R
= 8Ω + 33µH
L
NO LOAD
NO LOAD
4.5
4.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
2.5
3.0
3.5
4.0
4.5
5.0
5.5
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 18. Supply Current vs. Supply Voltage, Gain = 6 dB
Figure 21. Supply Current vs. Supply Voltage, Gain = 24 dB
Rev. A | Page 10 of 32
SSM2380
2.0
1.8
1.6
2.0
1.8
1.6
f = 1kHz
= 8Ω + 33µH
GAIN = 6dB
f = 1kHz
R = 8Ω + 33µH
L
GAIN = 24dB
R
L
1.4
1.2
1.0
0.8
0.6
0.4
1.4
1.2
1.0
0.8
0.6
0.4
THD + N = 10%
THD + N = 10%
THD + N = 1%
THD + N = 1%
0.2
0
0.2
0
2.5
3.0
3.5
4.0
4.5
5.0
2.5
3.0
3.5
4.0
4.5
5.0
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 22. Maximum Output Power vs. Supply Voltage, RL = 8 Ω, Gain = 6 dB
Figure 25. Maximum Output Power vs. Supply Voltage, RL = 8 Ω, Gain = 24 dB
3.5
3.5
f = 1kHz
f = 1kHz
R
= 4Ω + 15µH
R = 4Ω + 15µH
GAIN = 24dB
L
L
3.0
2.5
2.0
1.5
1.0
0.5
3.0
2.5
2.0
1.5
1.0
0.5
GAIN = 6dB
THD + N = 10%
THD + N = 10%
THD + N = 1%
THD + N = 1%
0
2.5
0
2.5
3.0
3.5
4.0
4.5
5.0
3.0
3.5
4.0
4.5
5.0
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 23. Maximum Output Power vs. Supply Voltage, RL = 4 Ω, Gain = 6 dB
Figure 26. Maximum Output Power vs. Supply Voltage, RL = 4 Ω, Gain = 24 dB
100
100
R
= 4Ω + 15µH
V
= 2.5V
L
DD
90
80
70
60
50
40
30
90
80
70
60
50
40
30
V
= 3.6V
R = 8Ω + 33µH
L
DD
V
= 5V
DD
V
= 3.6V
DD
V
= 2.5V
DD
V
= 5V
DD
20
10
0
20
10
0
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
OUTPUT POWER (W)
OUTPUT POWER (W)
Figure 24. Efficiency vs. Output Power into 8 Ω
Figure 27. Efficiency vs. Output Power into 4 Ω
Rev. A | Page 11 of 32
SSM2380
0.8
1.6
1.4
BOTH CHANNELS
= 8Ω + 33µH
GAIN = 6dB
BOTH CHANNELS
R = 4Ω + 15µH
L
GAIN = 6dB
R
L
0.7
0.6
0.5
0.4
0.3
1.2
1.0
0.8
0.6
V
= 5V
V
= 5V
DD
DD
V
= 3.6V
V
= 3.6V
DD
DD
V
= 2.5V
V
= 2.5V
DD
DD
0.2
0.1
0
0.4
0.2
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0
1
2
3
4
5
6
OUTPUT POWER (W)
OUTPUT POWER (W)
Figure 28. Supply Current vs. Output Power into 8 Ω
Figure 31. Supply Current vs. Output Power into 4 Ω
0
–10
–20
–30
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–40
–50
–60
–70
–80
–90
–100
10
100
1k
10k
100k
10
100
1k
10k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 29. Common-Mode Rejection Ratio (CMRR) vs. Frequency
Figure 32. Power Supply Rejection Ratio (PSRR) vs. Frequency
0
V
V
R
= 5V
DD
RIPPLE
= 8Ω + 33µH
= 500mV rms
–20
–40
–60
L
LEFT TO RIGHT
–80
RIGHT TO LEFT
–100
–120
–140
10
100
1k
10k
100k
FREQUENCY (Hz)
Figure 30. Crosstalk vs. Frequency
Rev. A | Page 12 of 32
SSM2380
6
5
6
5
OUTPUT
OUTPUT
SD INPUT
4
3
4
3
2
2
1
1
0
0
SD INPUT
–1
–2
–1
–2
–2
0
2
4
6
8
10
12
14
16
18
20
–160 –120 –80 –40
0
40
80
120 160 200 240
TIME (ms)
TIME (µs)
Figure 33. Turn-On Response
Figure 34. Turn-Off Response
Rev. A | Page 13 of 32
SSM2380
THEORY OF OPERATION
The SSM2380 has a pop-and-click suppression architecture that
reduces these output transients, resulting in noiseless activation
and deactivation.
OVERVIEW
The SSM2380 stereo, Class-D audio amplifier features a filterless
modulation scheme that greatly reduces the external component
count, conserving board space and, thus, reducing system cost.
The SSM2380 does not require an output filter but, instead, relies
on the inherent inductance of the speaker coil and the natural
filtering of the speaker and human ear to fully recover the audio
component of the square wave output.
OUTPUT MODULATION DESCRIPTION
The SSM2380 uses three-level, Σ-Δ output modulation. Each
output can swing from GND to VDD and vice versa. Ideally, when
no input signal is present, the output differential voltage is 0 V
because there is no need to generate a pulse. In a real-world
situation, noise sources are always present.
Most Class-D amplifiers use some variation of pulse-width
modulation (PWM), but the SSM2380 uses Σ-Δ modulation to
determine the switching pattern of the output devices, resulting
in a number of important benefits.
Due to the constant presence of noise, a differential pulse is
generated, when required, in response to this stimulus. A small
amount of current flows into the inductive load when the differ-
ential pulse is generated.
•
Σ-Δ modulators do not produce a sharp peak with many
harmonics in the AM frequency band, as pulse-width
modulators often do.
Most of the time, however, the output differential voltage is 0 V,
due to the Analog Devices, Inc., three-level, Σ-Δ output modu-
lation. This feature ensures that the current flowing through the
inductive load is small.
•
Σ-Δ modulation provides the benefits of reducing the
amplitude of spectral components at high frequencies,
that is, reducing EMI emissions that might otherwise
be radiated by speakers and long cable traces.
When the user wants to send an input signal, an output pulse
(OUTx+ and OUTx−) is generated to follow the input voltage.
The differential pulse density (VOUT) is increased by raising the
input signal level. Figure 35 depicts three-level, Σ-Δ output
modulation with and without input stimulus.
•
•
The SSM2380 does not require external EMI filtering for
twisted speaker cable lengths shorter than 10 cm. If longer
speaker cables are used, the SSM2380 has an emission sup-
pression mode that allows significantly longer speaker cable.
Due to the inherent spread-spectrum nature of Σ-Δ modu-
lation, the need for modulator synchronization is eliminated
for designs that incorporate multiple SSM2380 amplifiers.
OUTPUT = 0V
+5V
OUT+
0V
+5V
OUT–
0V
+5V
Using the I2C control interface, the gain of the SSM2380 can
be selected from 1 dB to 24 dB (plus mute) in 47 steps with no
external components and fixed input impedance. Other features
accessed from the I2C interface include the following:
V
0V
OUT
–5V
OUTPUT > 0V
+5V
OUT+
OUT–
0V
+5V
•
•
•
Independent left/right channel shutdown
Variable ultralow EMI emission control mode
Automatic level control (ALC) for high quality speaker
protection
0V
+5V
V
OUT
0V
OUTPUT < 0V
+5V
OUT+
OUT–
•
Stereo-to-mono mixing operation
0V
+5V
The SSM2380 also offers protection circuits for overcurrent and
overtemperature protection.
0V
0V
V
OUT
–5V
POP-AND-CLICK SUPPRESSION
Figure 35. Three-Level, Σ-Δ Output Modulation
With and Without Input Stimulus
Voltage transients at the output of audio amplifiers can occur
when shutdown is activated or deactivated. Voltage transients
as low as 10 mV can be heard as an audio pop in the speaker.
Clicks and pops can also be classified as undesirable audible
transients generated by the amplifier system and, therefore, as
not coming from the system input signal. Such transients may
be generated when the amplifier system changes its operating
mode. For example, the following may be sources of audible
transients: system power-up and power-down, mute and
unmute, input source change, and sample rate change.
Rev. A | Page 14 of 32
SSM2380
Maximum output power is derived from VTH using the
following equation:
OPERATING MODES
The SSM2380 has three unique operating modes, controlled by
the MODE pin. When MODE (Ball C2) is connected to GND,
the SSM2380 operates in I2C control mode; Ball C3 and Ball C4
function as SCK and SDA for the I2C input. In I2C control mode,
the user has full control of all internal registers of the SSM2380
(see Table 11).
2
(Limit×V )/100
⎛
⎞
DD
⎜
⎜
⎟
⎟
2
⎝
⎠
POUT
=
RSP
where RSP is the speaker impedance.
When MODE (Ball C2) is connected to VDD, the SSM2380
operates in gain select mode; Ball C3 and Ball C4 function as
the gain select pins, GAIN0 and GAIN1. All ALC and emission
control features are disabled in gain select mode, and the user
can set the gain to 6 dB, 12 dB, 18 dB, or 24 dB only.
95
90
85
80
75
70
65
60
When MODE (Ball C2) is not connected (floating), the SSM2380
operates in ALC mode; Ball C3 and Ball C4 function as EDGE and
ALCTH. In ALC mode, the default gain is 18 dB. The user can
enable or disable the emission control (EMI) feature by connect-
ing EDGE (Ball C3) to VDD or GND. In addition to emission
control, the ALC is activated. The user must connect a resistor
from ALCTH (Ball C4) to GND. This resistor allows the user to
TYPICAL CONDITION
55
INTERNAL RESISTOR – 20%
INTERNAL RESISTOR + 20%
50
limit the output level to any setting from 45% to 90% of VDD
.
45
100
1k
10k
100k
1M
RESISTOR (Ω)
Table 6. MODE Pin Selection Guide
Figure 36. Output Voltage Limit (VTH) vs. RTH
SSM2380 Ball
Operating Mode
Gain select mode
I2C control mode
Ball C2 (MODE)
Ball C3 Ball C4
In ALC mode, the attack, hold, and release times associated
with ALC operation are at fixed levels, as indicated in Table 7.
High (connected to VDD) GAIN0
Low (connected to GND) SCK
Open (floating)
GAIN1
SDA
Table 7. Attack, Hold, and Release Times for ALC Mode
EDGE
ALCTH ALC mode
Time
Duration
Attack Time
Hold Time
Release Time
256 ꢀs (per 0.5 dB step)
90 ms to 120 ms (nonadjustable)
128 ms (per 0.5 dB step)
ALC MODE OPERATION
When MODE is not connected (floating), the SSM2380 is in ALC
mode, disabling the I2C interface. In ALC mode, the user has
control of only two functions: setting the ALC threshold voltage
and activating or deactivating the emission limiting circuitry.
Activating or Deactivating the Emission Limiting Circuitry
To activate or deactivate the emission limiting circuitry, connect
EDGE (Ball C3) to GND or to VDD. When EDGE is connected
to GND, the SSM2380 is in normal operating mode, deactivating
the emission limiting function. The device operates with maximum
efficiency and noise level performance in this setting. The user
can also pass FCC Class B emission testing with 10 cm twisted
pair speaker wire for loudspeaker connection.
Setting the ALC Threshold Voltage
To set the ALC threshold voltage, connect ALCTH (Ball C4)
to GND with a series resistor. Figure 36 shows the relationship
between the RTH resistor setting and the output voltage limit as
a percentage of the supply rail.
To calculate the resistor value, use the following equations:
If longer speaker wire is desired, connect the EDGE pin to VDD
to activate the emission limiting circuitry. The trade-off is slightly
lower efficiency and noise performance. The penalty for using the
emission control circuitry is far less than the decreased perfor-
mance observed when using a ferrite bead based EMI filter for
emission limiting purposes.
Limit (%) = 100 × (REXT + 53)/(2.2 × REXT + 58) kꢀ
R
EXT = (53 − 58 × Limit/100)/(2.2 × (Limit/100 – 1))%
For example, to set an 80% limit,
EXT = (53 − 58 × 80/100)/(2.2 × (80/100 − 1) kꢀ
Therefore, 8.7 kΩ is required.
R
Rev. A | Page 15 of 32
SSM2380
Figure 37 shows the input vs. output and gain characteristics
of the ALC that is implemented in the SSM2380.
GAIN SELECT MODE OPERATION
When MODE is connected to VDD, the SSM2380 is in gain
select mode, disabling the I2C interface. The ALC and emission
limiting functions are also disabled. Ball C3 and Ball C4 function
as the gain select pins, GAIN0 and GAIN1. Table 8 shows the
user-selectable gain settings for the SSM2380.
5.6
5.2
4.8
4.4
4.0
3.6
Table 8. Gain Settings in Gain Select Mode
3.2
2.8
2.4
GAIN0 (Ball C3)
GAIN1 (Ball C4)
Gain Setting (dB)
GND
VDD
GND
VDD
GND
GND
VDD
VDD
6
2.0
12
18
24
INPUT
GAIN = 6dB
GAIN = 12dB
GAIN = 18dB
GAIN = 24dB
1.6
1.2
0.8
0.4
0
I2C CONTROL MODE OPERATION
0
20
40
60
80
100 120 140 160 180 200
TIME (ms)
When MODE is connected to GND, the SSM2380 operates in
I2C control mode, enabling Ball C3 and Ball C4 to act as SCK
and SDA for the I2C input. In I2C control mode, the user has
full control of all features of the SSM2380 (see Table 11).
Figure 37. Input vs. Output and Gain Characteristics
When the input level is small and below the ALC threshold value,
the gain of the amplifier stays at the preset gain setting. When
the input exceeds the ALC threshold value, the ALC gradually
reduces the gain from the preset gain setting down to 1 dB.
•
Gain control: 48-step, left/right independent control
(ALC is off)
ALC Compression and Limiting Modes
•
ALC control (limiter/compressor): configurable attack
and release times; configurable threshold voltage (16 level
settings, 64% to 96% of VDD); optional fixed-power mode
(does not track rail)
The ALC implemented on the SSM2380 has two operation
modes: compression and limiting. When the ALC is triggered
for medium-level input signals, the ALC is in compression mode.
In this mode, an increase of the output signal is one-third the
increase of the input signal. For example, if the input signal
increases by 3 dB, the ALC reduces the amplifier gain by 2 dB
and thus the output signal increases by only 1 dB.
•
•
Output stage: active emissions edge rate control
(four settings)
Mixer: option to send left channel input to both left and
right channel outputs or to send right channel input to
both outputs
As the input signal becomes very large, the ALC transitions to
limiting mode. In this mode, the output stays at a given threshold
level, VTH, even if the input signal grows larger. As an example of
limiting mode operation, when a large input signal increases by
3 dB, the ALC reduces the amplifier gain by 3 dB and thus the
output increases by 0 dB. When the amplifier gain is reduced to
1 dB, the ALC cannot reduce the gain further, and the output
increases again. This is because the total range of the ALC opera-
tion has bottomed out due to extreme input voltage at high gain. To
avoid potential speaker damage, the maximum input amplitude
should not be large enough to exceed the maximum attenuation
(to a level of 1 dB) of the limiting mode.
AUTOMATIC LEVEL CONTROL (ALC)
Automatic level control (ALC) is a function that automatically
adjusts amplifier gain to generate the desired output amplitude
with reference to a particular input stimulus. The primary use for
the ALC is to protect an audio power amplifier or speaker load
from the damaging effects of clipping or current overloading.
This is accomplished by limiting the output amplitude of the
amplifier upon reaching a preset threshold voltage. Another
benefit of the ALC is that it makes sound sources with a wide
dynamic range more intelligible by boosting low level signals,
while in turn limiting very high level signals.
Before activating the ALC by setting the ALC_EN bit (Bit 7 in
Register R4), the user has full control of the left and right channel
PGA gain (programmable in Register R0 and Register R1). After
the ALC is activated (ALC_EN = 1), the user has no control over
the gain settings in Register R0 and Register R1; the left channel
PGA gain is locked into the device and controls the gain for both
the left and right channels. To change the gain, the user must
reset the ALC_EN bit to 0 and then load the new gain settings.
Rev. A | Page 16 of 32
SSM2380
3.5
3.0
Attack Time, Hold Time, and Release Time
When the amplifier input signal exceeds a preset threshold,
the ALC reduces amplifier gain rapidly until the output voltage
settles to a target level. This target level is maintained for a certain
period. If the input voltage does not exceed the threshold again,
the ALC increases the gain gradually.
2.5
2.0
1.5
1.0
The attack time is the time taken to reduce the gain from maxi-
mum to minimum. The hold time is the time that the reduced
gain is maintained. The release time is the time taken to increase
the gain from minimum to maximum. These times are shown
in Table 9.
00 (LIMITER MODE)
01 (COMPRESSION MODE 1)
10 (COMPRESSION MODE 2)
11 (COMPRESSION MODE 3)
3.6V × 0.77 = 2.772V
0.5
0
Table 9. Attack, Hold, and Release Times for I2C Control Mode
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9 1.0
INPUT VOLTAGE (V)
Time1
Duration
Figure 39. Adjustable Compression Settings, VDD = 3.6 V,
ALC Threshold Level = 77%
Attack Time
Hold Time
Release Time
32 ꢀs to 4 ms (per 0.5 dB step)
90 ms to 120 ms
4 ms to 512 ms (per 0.5 dB step)
4.5
4.0
1 The attack time and release time can be adjusted using the I2C interface.
The hold time cannot be adjusted.
3.5
3.0
2.5
2.0
1.5
Soft-Knee Compression
Often performed using sophisticated DSP algorithms, soft-knee
compression provides maximum sound quality with effective
speaker protection. Instead of using a fixed compression setting
prior to limiting, the SSM2380 allows for a much more subtle
transition into limiting mode, preserving the original sound
quality of the source audio. Figure 38 to Figure 40 show the
various soft-knee compression settings. If desired, compression
can be disabled. When compression is disabled, the part operates
in limiter-only mode.
00 (LIMITER MODE)
1.0
01 (COMPRESSION MODE 1)
10 (COMPRESSION MODE 2)
11 (COMPRESSION MODE 3)
5.0V × 0.77 = 3.85V
0.5
0
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8 2.0
INPUT VOLTAGE (V)
Figure 40. Adjustable Compression Setting, VDD = 5.0 V,
ALC Threshold Level = 77%
2.5
ALC Soft Transition
The ALC operation of the SSM2380 incorporates techniques to
reduce the audible artifacts associated with gain change transi-
tions. First, the gain is changed in small increments of 0.5 dB.
In addition to this small step size, the rate of gain change is
reduced, proportional to the attack time setting. This feature
drastically reduces and virtually eliminates the presence of zipper
noise and other artifacts associated with gain transitions during
ALC operation. Figure 41 shows the soft transition operation.
2.0
1.5
1.0
00 (LIMITER MODE)
01 (COMPRESSION MODE 1)
10 (COMPRESSION MODE 2)
0.5
11 (COMPRESSION MODE 3)
2.5V × 0.77 = 1.925V
NORMAL TRANSITION
0
0
0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50
INPUT VOLTAGE (V)
0.5dB
Figure 38. Adjustable Compression Settings, VDD = 2.5 V,
ALC Threshold Level = 77%
SOFT TRANSITION (32µs TO 256µs)
0.5dB
Figure 41. Soft Transition
Rev. A | Page 17 of 32
SSM2380
When the ALC is active, the following options are acceptable:
MIXER MODE
When I2C control mode is activated, the user can send left
channel input to both left and right channel outputs or send
right channel input to both outputs. This is achieved by
selecting Register R2, Bit 0 or Bit 1.
•
•
•
Left output = left input; right output = right input
Left output = left input; right output = left input
Left output = right input; right output = right input
To use the following options, the ALC must be disabled:
Using Mixer Mode with the ALC
•
•
•
Left output = left input + right input; right output = right
input
Left output = left input; right output = left input + right
input
Left output = left input + right input; right output = left
input + right input
If the ALC is enabled and the user also wishes to use the mixer
operation, follow the guidelines in this section. Left channel
gain controls the ALC; therefore, sending left channel input
to the left and right channel outputs poses no problem for the
ALC. However, to source the right channel input to the left and
right channel outputs when using the ALC, the user must first
load the left channel gain (Register R0, Bit 7).
With the ALC disabled, the user can also use the full mixer
capability; that is, if the user wishes to mix the right and left
inputs for both the right and left outputs, the ALC must be
disabled. If the user needs both the mixing and ALC functions,
the left or right channel must be muted to avoid problems.
Rev. A | Page 18 of 32
SSM2380
APPLICATIONS INFORMATION
Table 10. Input Impedance for I2C Control Mode
LAYOUT
LGAIN[5:0],
RGAIN[5:0]
As output power increases, care must be taken to lay out printed
circuit board (PCB) traces and wires properly among the amplifier,
load, and power supply. A good practice is to use short, wide
PCB tracks to decrease voltage drops and minimize inductance.
Ensure that track widths are at least 200 mil for every inch of
track length for lowest DCR, and use 1 oz or 2 oz copper PCB
traces to further reduce IR drops and inductance. A poor layout
increases voltage drops, consequently affecting efficiency. Use
large traces for the power supply inputs and amplifier outputs
to minimize losses due to parasitic trace resistance.
Gain (dB)
24.0
23.5
23.0
22.5
22.0
21.5
21.0
20.5
20.0
19.5
19.0
18.5
18.0
17.5
17.0
16.5
16.0
15.5
15.0
14.5
14.0
13.5
13.0
12.5
12.0
11.5
11.0
10.5
10.0
9.5
9.0
8.5
8.0
7.5
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
RIN (kΩ)
7.3
7.7
8.1
8.5
101110
101101
101100
101011
101010
101001
101000
100111
100110
100101
100100
100011
100010
100001
100000
011111
011110
011101
011100
011011
011010
011001
011000
010111
010110
010101
010100
010011
010010
010001
010000
001111
001110
001101
001100
001011
001010
001001
001000
000111
000110
000101
000100
000011
000010
000001
000000
9.0
9.5
10.0
10.5
11.1
11.7
12.3
12.9
13.6
14.3
15.0
15.8
16.6
17.4
18.3
19.2
20.1
21.1
22.1
23.1
24.2
25.3
26.4
27.6
28.8
30.0
31.3
32.6
34.0
35.3
36.7
38.1
39.6
41.1
42.6
44.1
45.6
47.1
48.7
50.3
51.8
53.4
55.0
Proper grounding guidelines help to improve audio performance,
minimize crosstalk between channels, and prevent switching
noise from coupling into the audio signal. To maintain high
output swing and high peak output power, the PCB traces that
connect the output pins to the load, as well as the PCB traces to
the supply pins, should be as wide as possible to maintain the
minimum trace resistances. It is also recommended that a large
ground plane be used for minimum impedances.
In addition, good PCB layout isolates critical analog paths from
sources of high interference. High frequency circuits (analog and
digital) should be separated from low frequency circuits. Properly
designed multilayer PCBs can reduce EMI emissions and increase
immunity to the RF field by a factor of 10 or more compared with
double-sided boards. A multilayer board allows a complete layer
to be used for the ground plane, whereas the ground plane side
of a double-sided board is often disrupted by signal crossover.
If the system has separate analog and digital ground and power
planes, the analog ground plane should be directly beneath the
analog power plane, and, similarly, the digital ground plane should
be directly beneath the digital power plane. There should be no
overlap between analog and digital ground planes or between
analog and digital power planes.
INPUT CAPACITOR SELECTION
The SSM2380 does not require input coupling capacitors if the
input signal is biased from 1.0 V to VDD − 1.0 V. Input capacitors
are required if the input signal is not biased within this recom-
mended input dc common-mode voltage range, if high-pass
filtering is needed, or if a single-ended source is used. If high-
pass filtering is needed at the input, the input capacitor and the
input resistor of the SSM2380 form a high-pass filter whose
corner frequency is determined by the following equation:
fC = 1/(2π × RIN × CIN)
The input capacitor can significantly affect the performance of
the circuit. Not using input capacitors degrades both the output
offset of the amplifier and the dc PSRR performance.
In I2C control mode, the input impedance changes depending on
the gain setting from Register R0 and Register R1 (LGAIN[5:0]
and RGAIN[5:0] bits). Table 10 shows the RIN value for each
PGA gain setting.
1.0
Rev. A | Page 19 of 32
SSM2380
The power supply inputs must be decoupled with a good
quality, low ESL, low ESR capacitor, usually of approximately
4.7 μF. This capacitor bypasses low frequency noises to the
ground plane.
POWER SUPPLY DECOUPLING
To ensure high efficiency, low total harmonic distortion (THD),
and high PSRR, proper power supply decoupling is necessary.
Noise transients on the power supply lines are short-duration
voltage spikes. Although the actual switching frequency is typi-
cally 325 kHz, these spikes can contain frequency components
that extend into the hundreds of megahertz.
For high frequency transient noises, use a 0.1 μF capacitor
as close as possible to the VDD pins of the device. Placing the
decoupling capacitors as close as possible to the SSM2380 helps
to maintain efficient performance.
Rev. A | Page 20 of 32
SSM2380
TYPICAL APPLICATION CIRCUITS
GAIN
MODULATOR
MODULATOR
INL
OUTL
ALC
GAIN
INR
OUTR
Figure 42. SSM2380 Mixer Operation Block Diagram
VDD
B1
C26
MPZ1608S121A
OUT_L+
10µF
C27
0.1µF
C33
510pF
GND
A1
GND
H6
HDR1X2
C34
510pF
C22
R14
R15
0Ω
0Ω
D1
D2
B2
L INPUT +
L INPUT–
INL+
OUTL+
OUTL–
0.22µF
C23
MPZ1608S121A
OUT_L–
B1
INL–
0.22µF
U8
B3
SSM2380
MPZ1608S121A
C24
OUT_R+
R16
R17
0Ω
0Ω
D4
D3
A4
B4
R INPUT +
R INPUT–
INR+
INR–
OUTR+
OUTR–
0.22µF
C25
C35
510pF
0.22µF
C2
C4
C3
MODE
SDA
H7
HDR1X2
C1
GND
STDN
SD
C36
GND
SCK
510pF
B4
MPZ1608S121A
OUT_R–
GND
I2C[0..1]
SDA
SCK
I2CVDD
R20
2.5kΩ
R21
2.5kΩ
Figure 43. SSM2380 Typical Schematic, I2C Control Mode
10µF
VDD 2.5V TO 5.5V
0.1µF
SSM2380
VDD
VDD
FET
22nF
22nF
INR+
INR–
OUTR+
OUTR–
RIGHT IN+
RIGHT IN–
Σ-∆
MODULATOR
DRIVER
SCK
SDA
GAIN
CONTROL
(+ALC)
2
INTERNAL
EMI
I C
BIAS
OSCILLATOR CONTROL
MODE = GND
SD
SHUTDOWN
22nF
22nF
INL+
INL–
OUTL+
OUTL–
LEFT IN+
LEFT IN–
Σ-∆
FET
DRIVER
MODULATOR
GND
GND
2
I C OPERATION (MODE PIN = GND)
Figure 44. SSM2380 I2C Control Mode Configuration (MODE Pin = GND)
Rev. A | Page 21 of 32
SSM2380
VDD
B1
C26
MPZ1608S121A
OUT_L+
10µF
C27
0.1µF
C33
510pF
GND
H6
HDR1X2
GND
C34
510pF
C22
D1
D2
A1
B1
B2
L INPUT +
L INPUT–
INL+
INL–
OUTL+
OUTL–
0.22µF
C23
MPZ1608S121A
OUT_L–
0.22µF
U8
SSM2380
B3
MPZ1608S121A
C24
OUT_R+
D4
D3
A4
B4
R INPUT +
R INPUT –
INR+
INR–
OUTR+
OUTR–
0.22µF
C25
C35
510pF
0.22µF
C2
C3
C4
MODE
EDGE
H7
HDR1X2
C1
GND
STDN
SD
C36
ALCTH
510pF
B4
MPZ1608S121A
OUT_R–
FLOAT
EMI CTRL
GND
R20
12kΩ
ALC THRESHOLD RESISTOR
GND
Figure 45. SSM2380 Typical Schematic, ALC Mode
10µF
VDD 2.5V TO 5.5V
0.1µF
SSM2380
VDD
VDD
FET
22nF
22nF
INR+
INR–
OUTR+
OUTR–
RIGHT IN+
Σ-∆
MODULATOR
DRIVER
RIGHT IN–
18dB
GAIN
(+ALC)
2
I C
DISABLED
EDGE
SD
INTERNAL
EMI
MODE = OPEN
EMISSION CONTROL
SHUTDOWN
BIAS
OSCILLATOR CONTROL
22nF
22nF
INL+
INL–
OUTL+
OUTL–
LEFT IN+
LEFT IN–
Σ-∆
FET
DRIVER
MODULATOR
GND
GND
ALCTH
ALC OPERATION (MODE PIN = OPEN)
R
TH
Figure 46. SSM2380 ALC Mode Configuration (MODE Pin = Open (Floating))
Rev. A | Page 22 of 32
SSM2380
VDD
B1
C26
MPZ1608S121A
OUT_L+
10µF
C27
0.1µF
C33
510pF
GND
H6
HDR1X2
GND
C34
510pF
C22
R14
R15
0Ω
0Ω
D1
D2
A1
B1
B2
L INPUT +
L INPUT–
INL+
INL–
OUTL+
OUTL–
0.22µF
C23
MPZ1608S121A
OUT_L–
0.22µF
U8
SSM2380
B3
MPZ1608S121A
C24
OUT_R+
R16
R17
0Ω
0Ω
D4
D3
A4
B4
R INPUT +
R INPUT –
INR+
INR–
OUTR+
OUTR–
0.22µF
C25
C35
510pF
0.22µF
I2CVDD
C2
C4
C3
MODE
GAIN1
GAIN0
H7
HDR1X2
C1
STDN
GND
SD
C36
510pF
B4
MPZ1608S121A
OUT_R–
GND
GAIN SELECT G1
GAIN SELECT G0
Figure 47. SSM2380 Typical Schematic, Gain Select Mode
10µF
VDD 2.5V TO 5.5V
0.1µF
VDD
SSM2380
VDD
FET
22nF
INR+
INR–
OUTR+
OUTR–
RIGHT IN+
RIGHT IN–
Σ-∆
MODULATOR
DRIVER
22nF
2
I C
GAIN
CONTROL
INTERNAL
EMI
MODE = VDD
BIAS
DISABLED
OSCILLATOR CONTROL
SD
SHUTDOWN
22nF
22nF
INL+
INL–
OUTL+
OUTL–
LEFT IN+
LEFT IN–
Σ-∆
FET
DRIVER
MODULATOR
GND
GND
GAIN1
GAIN0
GAIN = 6dB, 12dB,
18dB, OR 24dB
GAIN OPERATION (MODE PIN = VDD)
Figure 48. SSM2380 Gain Select Mode Configuration (MODE Pin = VDD)
Rev. A | Page 23 of 32
SSM2380
I2C INTERFACE
The I2C interface provides access to the user-selectable control
registers and operates with a 2-wire interface.
SDA generates the serial control data-word, and SCK clocks the
serial data. The I2C bus address (Bits[A7:A1]) is 0x31 (01100010
for write and 01100011 for read). Bit A0 is the designated
read/write bit.
Each control register consists of 16 bits, MSB first. Bits[B15:B9]
are the register map address, and Bits[B8:B0] are the register data
for the associated register map.
SDA
SCK
S
P
8
9
8
9
8
9
1 TO 7
1 TO 7
1 TO 7
DATA
START ADDR
R/W
ACK
SUBADDRESS
ACK
ACK
STOP
Figure 49. SSM2380 2-Wire I2C Generalized Clocking Diagram
WRITE
S
S
A7 ... A1 A0 A(S) B15 ... B9 B8 A(S) B7 ... B0 A(S)
0
P
SEQUENCE
DEVICE
ADDRESS
REGISTER
ADDRESS
REGISTER
DATA
READ
SEQUENCE
A7 ... A1 A0 A(S)
0
B15 ... B9
0
A(S)
S
A7 ... A1 A0 A(S)
1
B7 ... B0 A(M)
...
0
B8 A(M)
0
P
DEVICE
ADDRESS
REGISTER
ADDRESS
DEVICE
ADDRESS
REGISTER
DATA
(SLAVE DRIVE)
S = START BIT.
P = STOP BIT.
2
A0 = I C R/W BIT.
A(S) = ACKNOWLEDGE BY SLAVE.
A(M) = ACKNOWLEDGE BY MASTER.
A(M) = ACKNOWLEDGE BY MASTER (INVERSION).
Figure 50. I2C Write and Read Sequences
Rev. A | Page 24 of 32
SSM2380
REGISTER MAP
Table 11. Register Map
Reg Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
LGAIN[5:0]
Bit 1
Bit 0
Default
R0
0x00
Left channel
gain control
LTOR
LMUTE
00100010
R1
0x01
Right channel RTOL
gain control
RMUTE
RGAIN[5:0]
00100010
R2
R3
R4
R5
R6
R7
R8
0x02
0x03
0x04
0x05
0x06
0x07
0x08
Mode control
ALC Control 1
0
0
0
0
EDGE[1:0]
OCREC
OTREC
R2L
L2R
00001100
00101011
01001011
00000011
00000000
00000000
00000000
RTIME[2:0]
LTIME[2:0]
ALC Control 2 ALC_EN
COMP[1:0]
ALC_VFIX
ALCLV[3:0]
Shutdown
Error
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
STDNR
STDNL
OCR
0
OCL
0
OTW
OTP
0
Error clear
Reset
0
0
0
0
0
Rev. A | Page 25 of 32
SSM2380
REGISTER MAP DETAILS
REGISTER R0: LEFT CHANNEL GAIN CONTROL, ADDRESS 0x00
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
LTOR
LMUTE
LGAIN[5:0]
Table 12. Left Channel Gain Control Register Bit Descriptions
Bits
Bit Name
Description
7
LTOR
Left-to-right channel gain data load control.
0 = disable simultaneous loading of left channel gain data to left and right channel registers (default).
1 = enable simultaneous loading of left channel gain data to left and right channel registers.
6
LMUTE
Left channel input mute.
0 = disable mute (default).
1 = enable mute on left channel amplifier.
[5:0]
LGAIN[5:0]
Left channel gain control. Each step represents a 0.5 dB increase in gain. For ALC operation, these bits control
the gain setting for both the left and right channels. If the ALC_EN bit in Register R4 is set to 1, these bits cannot
be changed.
Setting
000000
…
Gain
1 dB
…
100010
…
18 dB (default)
…
101101
101110 to 111111
23.5 dB
24 dB
REGISTER R1: RIGHT CHANNEL GAIN CONTROL, ADDRESS 0x01
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RTOL
RMUTE
RGAIN[5:0]
Table 13. Right Channel Gain Control Register Bit Descriptions
Bits
Bit Name
Description
7
RTOL
Right-to-left channel gain data load control.
0 = disable simultaneous loading of right channel gain data to left and right channel registers (default).
1 = enable simultaneous loading of right channel gain data to left and right channel registers.
6
RMUTE
Right channel input mute.
0 = disable mute (default).
1 = enable mute on right channel amplifier.
[5:0]
RGAIN[5:0]
Right channel gain control. Each step represents a 0.5 dB increase in gain. If the ALC_EN bit in Register R4 is set
to 1, these bits cannot be changed.
Setting
000000
…
Gain
1 dB
…
100010
…
18 dB (default)
…
101101
101110 to 111111
23.5 dB
24 dB
Rev. A | Page 26 of 32
SSM2380
REGISTER R2: MODE CONTROL, ADDRESS 0x02
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
EDGE[1:0]
OCREC
OTREC
R2L
L2R
Table 14. Mode Control Register Bit Descriptions
Bits
Bit Name
Description
[5:4]
EDGE[1:0]
Edge rate control.
Setting
00
01
Rate Control
Normal mode (default)
Slow edge
10
11
Slow edge (VDD > 3.0 V recommended)
Slow edge (VDD > 4.0 V recommended)
3
2
1
0
OCREC
OTREC
R2L
Overcurrent autorecovery enable.
0 = disabled.
1 = enabled (default).
Overtemperature autorecovery enable.
0 = disabled.
1 = enabled (default).
Right channel signal mix enable (send right channel input to left and right channel outputs).
0 = mix disabled (default).
1 = mix enabled.
L2R
Left channel signal mix enable (send left channel input to left and right channel outputs).
0 = mix disabled (default).
1 = mix enabled.
REGISTER R3: ALC CONTROL 1, ADDRESS 0x03
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
LTIME[2:0]
Bit 0
0
0
RTIME[2:0]
Table 15. ALC Control 1 Register Bit Descriptions
Bits
Bit Name
Description
[5:3]
RTIME[2:0]
Release time setting (0.5 dB step).
Setting
Release Time
000
001
4 ms/step (6 dB/48 ms)
8 ms/step
010
16 ms/step
011
32 ms/step
100
64 ms/step
101
110
128 ms/step (default)
256 ms/step
111
512 ms/step
[2:0]
LTIME[2:0]
Attack time setting (0.5 dB step).
Setting
000
001
Attack Time
32 ꢀs/step (6 dB/384 ꢀs)
64 ꢀs/step
010
128 ꢀs/step
011
100
256 ꢀs/step (default)
512 ꢀs/step
101
1 ms/step
110
2 ms/step
111
4 ms/step
Rev. A | Page 27 of 32
SSM2380
REGISTER R4: ALC CONTROL 2, ADDRESS 0x04
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ALC_EN
COMP[1:0]
ALC_VFIX
ALCLV[3:0]
Table 16. ALC Control 2 Register Bit Descriptions
Bits
Bit Name
Description
7
ALC_EN
ALC enable (gain setting loaded to ALC control).
0 = disabled (default).
1 = enabled.
[6:5]
COMP[1:0]
Compressor setting.
Setting
00
Compression
Limiter mode (1:∞)
01
Compression Mode 1 (1:4 to 1:∞)
10
11
Compression Mode 2 (1:1.7 to 1:4 to 1:∞) (default)
Compression Mode 3 (1:2 to 1:2.5 to 1:∞)
4
ALC_VFIX
ALC threshold mode setting.
0 = supply tracking (default).
1 = fixed power.
[3:0]
ALCLV[3:0]
ALC threshold level setting. See Table 17 for a complete list of the settings (default value is 1011).
Table 17. ALC Threshold Level Settings
Supply Tracking Mode
(ALC_VFIX = 0)
ALCLV[3:0]
Value
1111
1110
1101
1100
1011
1010
1001
1000
0111
0110
0101
0100
0011
0010
0001
0000
Fixed Power Mode (ALC_VFIX = 1)
% of VDD
96
93
90
88
85
83
80
78
76
74
72
70
69
67
66
64
Voltage Limit (V)
4.36
4.25
4.13
4.01
3.89
3.77
3.65
3.54
3.42
3.30
3.18
3.06
2.95
2.83
2.71
2.59
Power, 8 Ω Load (W)
Power, 4 Ω Load (W)
1.19
1.13
1.06
1.0
2.38
2.25
2.13
2.01
1.89
1.78
1.67
1.56
1.46
1.36
1.27
1.17
1.09
1.00
0.92
0.84
0.95
0.89
0.83
0.78
0.73
0.68
0.63
0.59
0.54
0.50
0.46
0.42
Rev. A | Page 28 of 32
SSM2380
REGISTER R5: SHUTDOWN, ADDRESS 0x05
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
0
STDNR
STDNL
Table 18. Shutdown Register Bit Descriptions
Bits
Bit Name
Description
1
STDNR
Right channel shutdown control.
0 = power up right channel.
1 = power down right channel (default).
0
STDNL
Left channel shutdown control.
0 = power up left channel.
1 = power down left channel (default).
REGISTER R6: ERROR, ADDRESS 0x06
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
OCR
OCL
OTW
OTP
Table 19. Error Register Bit Descriptions (Read-Only Register)
Bits
Bit Name
Description
3
OCR
Overcurrent error bit, right channel.
0 = no error detected (default).
1 = error state flagged (if OCREC bit in the mode control register is set to 1).
2
1
0
OCL
OTW
OTP
Overcurrent error bit, left channel.
0 = no error detected (default).
1 = error state flagged (if OCREC bit in the mode control register is set to 1).
Overtemperature warning bit.
0 = no error detected (default).
1 = warning state flagged (if OTREC bit in the mode control register is set to 1).
Overtemperature error bit.
0 = no error detected (default).
1 = error state flagged (if OTREC bit in the mode control register is set to 1).
REGISTER R7: ERROR CLEAR, ADDRESS 0x07
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
0
0
0
Table 20. Error Clear Register Bit Descriptions
Bits
Bit Name
Description
[7:0]
Error clear
Recovery from error condition. Used when autorecovery is disabled.
REGISTER R8: RESET, ADDRESS 0x08
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
0
0
0
Table 21. Reset Register Bit Descriptions
Bits
Bit Name
Description
[7:0]
Reset
Clear all registers to their default values. Used when autorecovery is disabled.
Rev. A | Page 29 of 32
SSM2380
OUTLINE DIMENSIONS
0.640
0.595
0.550
2.000
1.960 SQ
1.920
SEATING
PLANE
3
2
1
4
A
BALL 1
IDENTIFIER
B
C
D
0.340
0.320
0.300
0.50
REF
0.05 MAX
0.345
0.330
0.315
TOP VIEW
(BALL SIDE DOWN)
BOTTOM VIEW
(BALL SIDE UP)
COPLANARITY
0.270
0.240
0.210
Figure 51. 16-Ball Wafer Level Chip Scale Package [WLCSP]
(CB-16-3)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Temperature Range
Package Description
Package Option
CB-16-3
CB-16-3
SSM2380CBZ-REEL
SSM2380CBZ-REEL7
EVAL-SSM2380Z
−40°C to +85°C
−40°C to +85°C
16-Ball Wafer Level Chip Scale Package [WLCSP]
16-Ball Wafer Level Chip Scale Package [WLCSP]
Evaluation Board
1 Z = RoHS Compliant Part.
Rev. A | Page 30 of 32
SSM2380
NOTES
Rev. A | Page 31 of 32
SSM2380
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
©2010–2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08752-0-2/11(A)
Rev. A | Page 32 of 32
相关型号：
©2020 ICPDF网 联系我们和版权申明