EVAL-AD1974EBZ [ADI]
4 ADC with PLL, 192 kHz, 24-Bit Codec; 4 ADC,具有锁相环, 192千赫, 24位编解码器![EVAL-AD1974EBZ](http://pdffile.icpdf.com/pdf1/p00119/img/icpdf/EVAL-AD1974EB_654585_icpdf.jpg)
型号: | EVAL-AD1974EBZ |
厂家: | ![]() |
描述: | 4 ADC with PLL, 192 kHz, 24-Bit Codec |
文件: | 总24页 (文件大小:493K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
4 ADC with PLL,
192 kHz, 24-Bit Codec
AD1974
FEATURES
GENERAL DESCRIPTION
Phase-locked loop generated or direct master clock
Low EMI design
107 dB dynamic range and SNR
−94 dB THD + N
Single 3.3 V supply
Tolerance for 5 V logic inputs
The AD1974 is a high performance, single-chip codec that pro-
vides four analog-to-digital converters (ADCs) with differential
inputs using the Analog Devices, Inc. patented multibit sigma-
delta (Σ-Δ) architecture. An SPI port is included, allowing a
microcontroller to adjust volume and many other parameters.
The AD1974 operates from 3.3 V digital and analog supplies.
The AD1974 is available in a single-ended output 48-lead LQFP.
Supports 24 bits and 8 kHz to 192 kHz sample rates
Differential ADC input
The AD1974 is designed for low EMI. This consideration is
apparent in both the system and circuit design architectures.
By using the on-board phase-locked loop (PLL) to derive the
master clock from the LR clock or from an external crystal,
the AD1974 eliminates the need for a separate high frequency
master clock and can also be used with a suppressed bit clock.
The ADCs are designed using the latest continuous time archi-
tectures from Analog Devices to further minimize EMI. By
using 3.3 V supplies, power consumption is minimized, further
reducing emissions.
Log volume control with autoramp function
SPI®-controllable for flexibility
Software-controllable clickless mute
Software power-down
Right justified, left justified, I2S, and TDM modes
Master and slave modes up to 16-channel input/output
Available in a 48-lead LQFP
APPLICATIONS
Automotive audio systems
Home Theater Systems
Set-top boxes
Digital audio effects processors
FUNCTIONAL BLOCK DIAGRAM
DIGITAL AUDIO
INPUT/OUTPUT
AD1974
SERIAL DATA PORT
SDATA
OUT
ADC
QUAD
DEC
FILTER
ADC
ADC
ADC
ANALOG
AUDIO
INPUTS
CLOCKS
48kHz/
96kHz/192kHz
TIMING MANAGEMENT
AND CONTROL
(CLOCK AND PLL)
CONTROL PORT
SPI
PRECISION
VOLTAGE
REFERENCE
12.48MHz
CONTROL DATA
INPUT/OUTPUT
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2007 Analog Devices, Inc. All rights reserved.
AD1974
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 11
Analog-to-Digital Converters (ADCs).................................... 11
Clock Signals............................................................................... 11
Reset and Power-Down ............................................................. 11
Serial Control Port ..................................................................... 12
Power Supply and Voltage Reference....................................... 12
Serial Data Ports—Data Format............................................... 12
TDM Modes................................................................................ 13
Daisy-Chain Mode..................................................................... 15
Control Registers............................................................................ 18
PLL and Clock Control Registers............................................. 18
AUXPORT Control Registers................................................... 19
ADC Control Registers.............................................................. 20
Additional Modes....................................................................... 22
Application Circuits ....................................................................... 23
Outline Dimensions....................................................................... 24
Ordering Guide............................................................................... 24
Applications....................................................................................... 1
General Description......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Test Conditions............................................................................. 3
Analog Performance Specifications........................................... 3
Crystal Oscillator Specifications................................................. 4
Digital Input/Output Specifications........................................... 4
Power Supply Specifications........................................................ 5
Digital Filters................................................................................. 5
Timing Specifications .................................................................. 5
Absolute Maximum Ratings............................................................ 7
Thermal Resistance ...................................................................... 7
ESD Caution.................................................................................. 7
Pin Configuration and Function Descriptions............................. 8
Typical Performance Characteristics ........................................... 10
REVISION HISTORY
4/07—Revision 0: Initial Version
Rev. 0 | Page 2 of 24
AD1974
SPECIFICATIONS
TEST CONDITIONS
Performance of all channels is identical, exclusive of the interchannel gain mismatch and interchannel phase deviation specifications.
Supply Voltages (AVDD, DVDD)
Temperature Range 1
Master Clock
3.3 V
As specified in Table 1 and Table 2
12.288 MHz (48 kHz fS, 256 × fS mode)
Input Sample Rate
48 kHz
Measurement Bandwidth
Word Width
20 Hz to 20 kHz
24 bits
Load Capacitance (Digital Output) 20 pF
Load Current (Digital Output)
Input Voltage High
1 mA or 1.5 kΩ to ½ DVDD supply
2.0 V
0.8 V
Input Voltage Low
1 Functionally guaranteed at −40°C to +125°C case temperature.
ANALOG PERFORMANCE SPECIFICATIONS
Specifications guaranteed at 25°C (ambient).
Table 1.
Parameter
Conditions
Min
Typ
Max
Unit
ANALOG-TO-DIGITAL CONVERTERS
ADC Resolution
All ADCs
24
Bits
Full-Scale Input Voltage (Differential)
Dynamic Range
1.9
V rms
20 Hz to 20 kHz, −60 dB input
No Filter (RMS)
With A-Weighted Filter (RMS)
Total Harmonic Distortion + Noise (THD + N) −1 dBFS
98
100
102
105
−96
dB
dB
dB
−87
Gain Error
−10
+10
%
Interchannel Gain Mismatch
Offset Error
Gain Drift
Interchannel Isolation
CMRR
−0.25
−10
+0.25
+10
dB
0
mV
ppm/°C
dB
100
−110
55
100 mV rms, 1 kHz
dB
100 mV rms, 20 kHz
55
dB
Input Resistance
Input Capacitance
14
10
kΩ
pF
Input Common-Mode Bias Voltage
REFERENCE
1.5
V
Internal Reference Voltage
External Reference Voltage
Common-Mode Reference Output
FILTR pin
FILTR pin
CM pin
1.50
1.50
1.50
V
V
V
1.32
1.68
Rev. 0 | Page 3 of 24
AD1974
Specifications measured at 130°C (case).
Table 2.
Parameter
Conditions
Min
Typ
Max
Unit
ANALOG-TO-DIGITAL CONVERTERS
ADC Resolution
All ADCs
24
Bits
Full-Scale Input Voltage (Differential)
Dynamic Range
1.9
V rms
20 Hz to 20 kHz, −60 dB input
No Filter (RMS)
With A-Weighted Filter (RMS)
Total Harmonic Distortion + Noise (THD + N) −1 dBFS
Gain Error
95
97
102
105
−96
dB
dB
dB
%
−87
+10
−10
Interchannel Gain Mismatch
Offset Error
−0.25
−10
+0.25
+10
dB
mV
0
REFERENCE
Internal Reference Voltage
External Reference Voltage
Common-Mode Reference Output
FILTR pin
FILTR pin
CM pin
1.50
1.50
1.50
V
V
V
1.32
1.68
CRYSTAL OSCILLATOR SPECIFICATIONS
Table 3.
Parameter
Min
Typ
Max
Unit
Transconductance
3.5
Mmhos
DIGITAL INPUT/OUTPUT SPECIFICATIONS
−40°C < TA < +130°C, DVDD = 3.3 V 10ꢀ.
Table 4.
Parameter
Conditions/Comments
Min
2.0
2.2
Typ
Max
Unit
V
V
Input Voltage High (VIH)
Input Voltage High (VIH)
Input Voltage Low (VIL)
Input Leakage
MCLKI pin
0.8
10
10
V
IIH @ VIH = 2.4 V
IIL @ VIL = 0.8 V
IOH = 1 mA
μA
μA
V
High Level Output Voltage (VOH
)
DVDD − 0.60
Low Level Output Voltage (VOL
Input Capacitance
)
IOL = 1 mA
0.4
5
V
pF
Rev. 0 | Page 4 of 24
AD1974
POWER SUPPLY SPECIFICATIONS
Table 5.
Parameter
SUPPLIES
Voltage
Conditions/Comments
Min
Typ
Max
Unit
DVDD
AVDD
3.0
3.0
3.3
3.3
3.6
3.6
V
V
Digital Current
Normal Operation
MCLK = 256 fS
fS = 48 kHz
fS = 96 kHz
fS = 192 kHz
fS = 48 kHz to 192 kHz
56
65
95
2.0
mA
mA
mA
mA
Power-Down
Analog Current
Normal Operation
Power-Down
74
23
mA
mA
DISSIPATION
Operation
MCLK = 256 fS, 48 kHz
All Supplies
Digital Supply
Analog Supply
429
185
244
83
mW
mW
mW
mW
Power-Down, All Supplies
POWER SUPPLY REJECTION RATIO
Signal at Analog Supply Pins
1 kHz, 200 mV p-p
20 kHz, 200 mV p-p
50
50
dB
dB
DIGITAL FILTERS
Table 6.
Parameter
Mode
All modes @ 48 kHz
Factor
Min
Typ
Max
Unit
ADC DECIMATION FILTER
Pass Band
Pass-Band Ripple
Transition Band
Stop Band
0.4375 fS
21
0.015
24
27
kHz
dB
kHz
kHz
dB
0.5 fS
0.5625 fS
Stop-Band Attenuation
Group Delay
79
22.9844 fS
479
μs
TIMING SPECIFICATIONS
−40°C < TA < +130°C, DVDD = 3.3 V 10ꢀ.
Table 7.
Parameter
Condition
Comments
Min
Max Unit
INPUT MASTER CLOCK (MCLK)
AND RESET
tMH
tMH
MCLK duty cycle
MCLK frequency
ADC clock source = PLL clock @ 256 fS, 384 fS, 512 fS, 768 fS 40
60
60
%
%
ADC clock source = direct MCLK @ 512 fS (bypass
on-chip PLL)
40
fMCLK
fMCLK
tPDR
PLL mode, 256 fS reference
Direct 512 fS mode
6.9
13.8 MHz
27.6 MHz
ns
Low
15
tPDRR
Recovery
Reset to active output
4096
tMCLK
Rev. 0 | Page 5 of 24
AD1974
Parameter
PLL
Condition
Comments
Min
Max Unit
Lock Time
256 fS VCO Clock
Output Duty Cycle
MCLK_O Pin
SPI PORT
tCCH
MCLK and LRCLK input
10
60
ms
%
40
See Figure 5
CCLK high
CCLK low
35
35
ns
ns
tCCL
fCCLK
CCLK frequency
fCCLK = 1/tCCP; only tCCP shown in Figure 5
10
MHz
tCDS
tCDH
tCLS
tCLH
tCLHIGH
tCOE
tCOD
tCOH
CDATA setup
CDATA hold
Setup
Hold
High
COUT enable
COUT delay
COUT hold
COUT tristate
To CCLK rising
From CCLK rising
To CCLK rising
From CCLK falling
Not shown in Figure 5
From CCLK falling
From CCLK falling
From CCLK falling, not shown in Figure 5
From CCLK falling
10
10
10
10
10
ns
ns
ns
ns
ns
ns
ns
ns
ns
30
30
30
tCOTS
30
ADC SERIAL PORT
See Figure 13
tABH
tABL
tALS
tALH
tALS
tABDD
ABCLK high
ABCLK low
ALRCLK setup
ALRCLK hold
ALRCLK skew
ASDATA delay
Slave mode
Slave mode
10
10
10
5
ns
ns
ns
ns
ns
ns
To ABCLK rising, slave mode
From ABCLK rising, slave mode
From ABCLK falling, master mode
From ABCLK falling
See Figure 12
−8
+8
18
AUXILIARY INTERFACE
tXDS
tXDH
tXBH
tXBL
tXLS
tXLH
AAUXDATA setup
AAUXDATA hold
AUXBCLK high
AUXBCLK low
AUXLRCLK setup
AUXLRCLK hold
To AUXBCLK rising
From AUXBCLK rising
10
5
10
10
10
5
ns
ns
ns
ns
ns
ns
To AUXBCLK rising
From AUXBCLK rising
Rev. 0 | Page 6 of 24
AD1974
ABSOLUTE MAXIMUM RATINGS
Table 8.
THERMAL RESISTANCE
Parameter
Rating
θJA represents thermal resistance, junction-to-ambient; θJC
represents the thermal resistance, junction-to-case. All
characteristics are for a 4-layer board.
Analog (AVDD)
Digital (DVDD)
Input Current (Except Supply Pins)
Analog Input Voltage (Signal Pins)
Digital Input Voltage (Signal Pins)
−0.3 V to +3.6 V
−0.3 V to +3.6 V
20 mA
–0.3 V to AVDD + 0.3 V
−0.3 V to DVDD + 0.3 V
Table 9.
Package Type
θJA
θJC
Unit
Operating Temperature Range (Case) −40°C to +125°C
Storage Temperature Range −65°C to +150°C
48-Lead LQFP
50.1
17
°C/W
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 7 of 24
AD1974
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
48 47 46 45 44 43 42 41 40 39 38 37
1
2
36
35
34
33
32
31
30
29
28
27
26
25
AGND
MCLKI/XI
MCLKO/XO
AGND
AVDD
NC
AGND
FILTR
AGND
AVDD
AGND
NC
3
4
5
AD1974
TOP VIEW
(Not to Scale)
6
7
NC
NC
SINGLE-ENDED
OUTPUT
8
NC
NC
9
NC
NC
10
11
12
PD/RST
NC
CLATCH
CCLK
DGND
DGND
13 14 15 16 17 18 19 20 21 22 23 24
NC = NO CONNECT
Figure 2. AD1974 Single-Ended Output, 48-Lead LQFP Pin Configuration
Table 10. Pin Function Description
Pin No.
Type1 Mnemonic
Description
1, 4, 32, 34, 36
I
AGND
Analog Ground.
2
3
I
O
I
MCLKI/XI
MCLKO/XO
AVDD
Master Clock Input/Crystal Oscillator Input.
Master Clock Output/Crystal Oscillator Output.
Analog Power Supply. Connect to analog 3.3 V supply.
No Connect.
5, 33, 37, 48
6 to 9, 11, 16, 28 to 31
NC
10
12, 25
13
14
15
17
18
19
20
21
22
23
24
26
27
35
38
39
40
41
42
43
I
PD/RST
DGND
DVDD
AUXDATA2
AUXDATA1
AUXBCLK
AUXLRCLK
ASDATA2
ASDATA1
ABCLK
ALRCLK
CIN
COUT
CCLK
CLATCH
FILTR
Power-Down/Reset (Active Low).
I
I
Digital Ground.
Digital Power Supply. Connect to digital 3.3 V supply.
Auxiliary Data Input 2 (From External ADC 2).
Auxiliary Data Input 1 (From External ADC 1).
Auxiliary Bit Clock.
I/O
I/O
I/O
I/O
I/O
O
I/O
I/O
I
Auxiliary Left-Right Framing Clock.
ADC Serial Data Output 2 (ADC 2 Left and ADC 2 Right)/ADC TDM Data Input.
ADC Serial Data Output 1 (ADC 1 Left and ADC 1 Right)/ADC TDM Data Output.
Serial Bit Clock for ADCs.
Left-Right Framing Clock for ADCs.
Control Data Input (SPI).
Control Data Output (SPI).
Control Clock Input (SPI).
Latch Input for Control Data (SPI).
I/O
I
I
O
O
I
I
I
Voltage Reference Filter Capacitor Connection. Bypass with 10 μF||100 nF to AGND.
Common-Mode Reference Filter Capacitor Connection. Bypass with 47 μF||100 nF to AGND.
ADC1 Left Positive Input.
ADC1 Left Negative Input.
ADC1 Right Positive Input.
CM
ADC1LP
ADC1LN
ADC1RP
ADC1RN
ADC2LP
I
I
ADC1 Right Negative Input.
ADC2 Left Positive Input.
Rev. 0 | Page 8 of 24
AD1974
Pin No.
44
45
46
47
Type1 Mnemonic
Description
I
ADC2LN
ADC2RP
ADC2RN
LF
ADC2 Left Negative Input.
ADC2 Right Positive Input.
ADC2 Right Negative Input.
PLL Loop Filter, Return to AVDD.
I
I
O
1 I = input, O = output.
Rev. 0 | Page 9 of 24
AD1974
TYPICAL PERFORMANCE CHARACTERISTICS
0.10
0.08
0.06
0.04
0.02
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–0.02
–0.04
–0.06
–0.08
–0.10
0
5000 10000 15000 20000 25000 30000 35000 40000
FREQUENCY (kHz)
0
2000 4000 6000 8000 10000 12000 14000 16000 18000
FREQUENCY (kHz)
Figure 4. ADC Stop-Band Filter Response, 48 kHz
Figure 3. ADC Pass-Band Filter Response, 48 kHz
Rev. 0 | Page 10 of 24
AD1974
THEORY OF OPERATION
The internal clock for the ADCs is 256 × fS for all clock modes.
By default, the on-board PLL generates this internal master clock
from an external clock. A direct 512 × fS (referenced to 48 kHz
mode) master clock can be used for the ADCs if selected in the
PLL and Clock Control 1 register.
ANALOG-TO-DIGITAL CONVERTERS (ADCS)
There are four ADC channels in the AD1974 configured as two
stereo pairs with differential inputs. The ADCs can operate at a
nominal sample rate of 48 kHz, 96 kHz, or 192 kHz. The ADCs
include on-board digital antialiasing filters with a 79 dB stop-
band attenuation and a linear phase response, operating at
an oversampling ratio of 128 (48 kHz, 96 kHz, and 192 kHz
modes). Digital outputs are supplied through two serial data
output pins (one for each stereo pair) as well as a common
frame (ALRCLK) and bit clock (ABCLK). Alternatively, one
of the time division multiplexed (TDM) modes can be used
to access up to 16 channels on a single TDM data line.
Note that it is not possible to use a direct clock for the ADCs
set to the 192 kHz mode. It is required that the on-chip PLL be
used in this mode.
The PLL can be powered down in the PLL and Clock Control 0
register. To ensure reliable locking when changing PLL modes,
or if the reference clock is unstable at power-on, power down
the PLL and then power it back up when the reference clock has
stabilized.
The ADCs must be driven from a differential signal source for
best performance. The input pins of the ADCs connect to inter-
nal switched capacitors. To isolate the external driving op amp
from the glitches caused by the internal switched capacitors,
each input pin should be isolated by using a series connected,
external, 100 Ω resistor together with a 1 nF capacitor connected
from each input to ground. This capacitor must be of high quality,
for instance, a ceramic NPO capacitor or a polypropylene film
capacitor.
The internal MCLK can be disabled in the PLL and Clock Control
0 register to reduce power dissipation when the AD1974 is idle.
The clock should be stable before it is enabled. Unless a stand-
alone mode is selected (see the Serial Control Port section), the
clock is disabled by reset and must be enabled by writing to the
SPI or I2C port for normal operation.
To maintain the highest performance possible, it is recom-
mended that the clock jitter of the internal master clock signal
be limited to less than 300 ps rms time interval error (TIE). Even
at these levels, extra noise or tones can appear in the outputs if
the jitter spectrum contains large spectral peaks. If the internal
PLL is not being used, it is highly recommended that an inde-
pendent crystal oscillator generate the master clock. In addition,
it is especially important that the clock signal should not be
passed through an FPGA, CPLD, DSP, or other large digital
chip before being applied to the AD1974. In most cases, this
induces clock jitter due to the sharing of common power and
ground connections with other unrelated digital output signals.
When the PLL is used, jitter in the reference clock is attenuated
above a certain frequency depending on the loop filter.
The differential inputs have a nominal common-mode voltage
of 1.5 V. The voltage at the common-mode reference pin (CM)
can be used to bias external op amps to buffer the input signals
(see the Power Supply and Voltage Reference section). The inputs
can also be ac-coupled and do not need an external dc bias to CM.
A digital high-pass filter can be switched in line with the ADCs
under serial control to remove residual dc offsets. It has a 1.4 Hz,
6 dB per octave cutoff at a 48 kHz sample rate. The cutoff fre-
quency scales directly with sample frequency.
The voltage at CM can be used to bias the external op amps that
buffer the output signals (see the Power Supply and Voltage
Reference section).
RESET AND POWER-DOWN
CLOCK SIGNALS
The reset pin sets all the control registers to their default settings.
To avoid pops, reset does not power down the analog outputs.
After reset is deasserted, and the PLL acquires a lock condition,
an initialization routine runs inside the AD1974. This initializa-
tion lasts for approximately 256 master clock cycles.
The on-chip PLL can be selected to reference the input sample
rate from either the LRCLK or AUXLRCK pins or 256, 384, 512,
or 768 times the sample rate, referenced to the 48 kHz mode from
the MCLKI/XI pin. The default at power-up is 256 × fS from
MCLKI. In 96 kHz mode, the master clock frequency stays
at the same absolute frequency; therefore, the actual mul-
tiplication rate is divided by 2. In 192 kHz mode, the actual
multiplication rate is divided by 4. For example, if the AD1974
is programmed in 256 × fS mode, the frequency of the master
clock input is 256 × 48 kHz = 12.288 MHz. If the AD1974 is
then switched to 96 kHz operation (by writing to the SPI or
I2C port), the frequency of the master clock should remain at
12.288 MHz (128 × fS). In 192 kHz mode, this becomes 64 × fS.
The PLL and Clock Control 0 register and the ADC Control 1
register power down their respective sections using power down
PD RST
bits. All other register settings are retained. The
/
pin
should be pulled low by an external resistor to guarantee proper
startup.
Rev. 0 | Page 11 of 24
AD1974
Table 11. Standalone Mode Selection
CLATCH
ADC Clocks
Slave
Master
CIN
0
0
COUT
CCLK
0
1
0
0
0
0
tCLS
tCLH
tCCH tCCL
tCCP
CLATCH
tCOTS
CCLK
tCDS tCDH
CIN
D23
D22
D9
D8
D8
D0
D0
tCOE
COUT
D9
tCOD
Figure 5. Format of the SPI Signal
means of a ferrite bead in series with each supply. It is
important that the analog supply be as clean as possible.
SERIAL CONTROL PORT
The AD1974 has an SPI control port that permits the program-
ming and reading back of the internal control registers for the
ADCs and the clock system. There is also a standalone mode
available for operation without serial control that is configured
at reset using the serial control pins. All registers are set to
default, except the internal MCLK enable, which is set to 1;
ADC BCLK and LRCLK master/slave, which are set by COUT.
Standalone mode only supports stereo mode with an I2S data
format and 256 fS MCLK rate (see Table 11 for details). Using a
weak pull-up resistor in applications that have a microcontroller
is highly recommended. This pull-up resistor ensures that the
AD1974 recognizes the presence of a microcontroller.
All digital inputs are compatible with TTL and CMOS levels.
All outputs are driven from the 3.3 V DVDD supply and are
compatible with TTL and 3.3 V CMOS levels.
The ADC internal voltage reference (VREF) is brought out
on FILTR and should be bypassed as close as possible to the
AD1974 with a parallel combination of 10 μF and 100 nF. Any
external current drawn should be limited to less than 50 μA.
VREF can be disabled in the PLL and Clock Control 1 register
and FILTR can be driven from an external source. The ADC
input gain varies by the inverse ratio.
CM is the internal common-mode reference. It should be
bypassed as close as possible to the AD1974, with a parallel
combination of 47 μF and 100 nF. This voltage can be used to
bias external op amps to the common-mode voltage of the input
and output signal pins. The output current should be limited to
less than 0.5 mA source and 2 mA sink.
The SPI control port of the AD1974 is a 4-wire serial control
port. The format is similar to that of the Motorola SPI® format
except that the input data-word is 24 bits wide. The serial bit
clock and latch can be completely asynchronous to the sample
rate of the ADCs. Figure 5 shows the format of the SPI signal.
The first byte is a global address with a read/write bit. For the
W
AD1974, the address is 0x04, shifted left one bit due to the R/
bit. The second byte is the AD1974 register address and the
third byte is the data.
SERIAL DATA PORTS—DATA FORMAT
The four ADC channels use a common serial bit clock (ABCLK)
and a left-right framing clock (ALRCLK) in the serial data port.
The clock signals are all synchronous with the sample rate. The
normal stereo serial modes are shown in Figure 11.
The ADC serial data modes default to I2S. The ports can also be
programmed for left justified, right justified, and TDM modes.
The word width is 24 bits by default and can be programmed
for 16 or 20 bits. The ADC serial formats and serial clock polarity
are programmable according to the ADC Control 1 register.
The ADC serial ports are programmable to become the bus
masters according to the ADC Control 2 register. By default,
both ADC serial ports are in the slave mode.
POWER SUPPLY AND VOLTAGE REFERENCE
The AD1974 is designed for 3.3 V supplies. Separate power
supply pins (Pin 5, Pin 13, Pin 33, Pin 37, and Pin 38) are pro-
vided for the analog and digital sections. These pins should be
bypassed with 100 nF ceramic chip capacitors, as close to the
pins as possible, to minimize noise pickup. A bulk aluminum
electrolytic capacitor of at least 22 μF should also be placed
on the same PC board as the codec. For critical applications,
improved performance is obtained with separate supplies for
the analog and digital sections. If this is not possible, it is rec-
ommended that the analog and digital supplies be isolated by
Rev. 0 | Page 12 of 24
AD1974
put stream follow four on-chip ADC channel slots. It should be
noted that due to the high ABCLK frequency, this mode is
available only in the 48 kHz/44.1 kHz/32 kHz sample rate.
TDM MODES
The AD1974 serial ports also have several different TDM serial
data modes. The first and most commonly used configuration
is shown in Figure 6 where the ADC serial port outputs one
data stream consisting of four on-chip ADCs followed by four
unused slots. In this mode, ABCLK is set to 256 fS (8-channel
TDM mode).
ALRCLK
256 BCLKs
ABCLK
32 BCLKs
SLOT 1 SLOT 2 SLOT 3 SLOT 4
LEFT 1 RIGHT 1 LEFT 2 RIGHT 2
UNUSED UNUSED UNUSED UNUSED
ADATA
The I/O pins of the serial ports are defined according to the
serial mode selected. For a detailed description of the function
of each pin in TDM and AUX Modes, see Table 12.
ALRCLK
ABCLK
MSB
MSB–1
MSB–2
ADATA
The AD1974 allows system configurations with more than four
ADC channels (see Figure 7 and Figure 8) that use 8 ADCs and
16 ADCs. In this mode, four AUX channel slots in the TDM out-
Figure 6. ADC TDM (8-Channel I2S Mode.
Table 12. Pin Function Changes in TDM and AUX Modes
Pin Name
ASDATA1
ASDATA2
AUXDATA1
AUXDATA2
ALRCLK
ABCLK
AUXLRCLK
AUXBCLK
Stereo Mode
TDM Mode
AUX Mode
ADC1 data output
ADC2 data output
Not used (ground)
Not used (ground)
ADC LRCLK input/output
ADC BCLK input/output
Not used (ground)
Not used (ground)
ADC TDM data output
ADC TDM data input
Not used (ground)
ADCTDM data output
Not used (float)
AUXDATA in 1 (from external ADC1)
AUXDATA in 2 (from external ADC2)
ADCTDM frame sync input/output
ADCTDM BCLK input/output
AUXLRCLK input/output
Not used (ground)
ADC TDM frame sync input/output
ADC TDM BCLK input/output
Not used (ground)
Not used (ground)
AUXBCLK input/output
ALRCLK
ABCLK
FOUR-AUX ADC CHANNELS
FOUR-ON-CHIP DAC CHANNELS
ADCR1 ADCL2
ASDATA1
(TDM_OUT)
ADCL1
ADCR2
AUXL1
AUXR1
AUXL2
AUXR2
32 BITS
MSB
AUXLRCLK
(AUX PORT)
LEFT
RIGHT
AUXBCLK
(AUX PORT)
AUXDATA1
(AUX1_IN)
MSB
MSB
MSB
AUXDATA2
(AUX2_IN)
MSB
Figure 7. 8-Channel AUX ADC Mode
Rev. 0 | Page 13 of 24
AD1974
ALRCLK
ABCLK
FOUR-ON-CHIP
ADC CHANNELS
AUXILIARY ADC CHANNELS
UNUSED SLOTS
ASDATA1
(TDM_OUT)
ADCL1 ADCR1 ADCL2 ADCR2 AUXL1 AUXR1 AUXL2 AUXR2 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED
32 BITS
MSB
AUXLRCLK
(AUX PORT)
LEFT
RIGHT
AUXBCLK
(AUX PORT)
AUXDATA1
(AUX1_IN)
MSB
MSB
MSB
AUXDATA2
(AUX2_IN)
MSB
Figure 8. 16-Channel AUX ADC Mode
Rev. 0 | Page 14 of 24
AD1974
The I/O pins of the serial ports are defined according to the
DAISY-CHAIN MODE
serial mode selected. See Table 13 for a detailed description
of the function of each pin. See Figure 14 for a typical AD1974
configuration with two external stereo ADCs.
The AD1974 also allows a daisy-chain configuration to
expand the system to 8 ADCs and 16 ADCs (see Figure 9 and
Figure 10). There are two configurations for the ADC port to
work in daisy-chain mode. The first one is with an ABCLK at
256 fS shown in Figure 9. The second configuration is with an
ABCLK at 512 fS shown in Figure 10. Note that in the 512 fS
ABCLK mode, the ADC channels occupy the first eight slots,
the second eight slots are empty. The TDM_IN of the first
AD1974 must be grounded in all modes of operation. The
second AD1974 is the device attached to the DSP TDM port.
Figure 11 through Figure 13 show the serial mode formats.
For maximum flexibility, the polarity of LRCLK and BCLK
are programmable. All of the clocks are shown with their
normal polarity. The default mode is I2S.
ALRCLK
ABCLK
FOUR ADC CHANNELS OF THE SECOND IC IN THE CHAIN
ASDATA1 (TDM_OUT
FOUR ADC CHANNELS OF THE FIRST IC IN THE CHAIN
ADCL1
ADCR1
ADCL2
ADCR2
ADCL1
ADCR1
ADCL2
ADCR2
OF THE SECOND AD1974
IN THE CHAIN)
ASDATA2 (TDM_IN
OF THE SECOND AD1974
IN THE CHAIN)
ADCL1
ADCR1
ADCL2
ADCR2
32 BITS
FIRST
AD1974
SECOND
AD1974
DSP
MSB
Figure 9. ADC TDM Daisy-Chain Mode (256 fS ABCLK, Two AD1974 Daisy Chains)
ALRCLK
ABCLK
FOUR ADC CHANNELS OF
FOUR ADC CHANNELS OF
THE SECOND IC IN THE CHAIN THE FIRST IC IN THE CHAIN
ASDATA1 (TDM_OUT
OF THE SECOND AD1974
IN THE CHAIN)
ADCL1 ADCR1 ADCL2 ADCR2 ADCL1 ADCR1 ADCL2 ADCR2 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED
ASDATA2 (TDM_IN
OF THE SECOND AD1974
IN THE CHAIN)
ADCL1 ADCR1 ADCL2 ADCR2 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED
32 BITS
FIRST
AD1974
SECOND
DSP
AD1974
MSB
Figure 10. ADC TDM Daisy-Chain Mode (512 fS ABCLK, Two AD1974 Daisy Chains)
Rev. 0 | Page 15 of 24
AD1974
LEFT CHANNEL
RIGHT CHANNEL
ALRCLK
ABCLK
ASDATA
MSB
LSB
MSB
LSB
LEFT JUSTIFIED MODE—16 BITS TO 24 BITS PER CHANNEL
LEFT CHANNEL
ALRCLK
RIGHT CHANNEL
ABCLK
MSB
I S MODE—16 BITS TO 24 BITS PER CHANNEL
LSB
ASDATA
MSB
LSB
2
LEFT CHANNEL
RIGHT CHANNEL
ALRCLK
ABCLK
ASDATA
MSB
LSB
MSB
LSB
RIGHT JUSTIFIED MODE—SELECT NUMBER OF BITS PER CHANNEL
ALRCLK
ABCLK
MSB
MSB
ASDATA
LSB
LSB
DSP MODE—16 BITS TO 24 BITS PER CHANNEL
1/fS
NOTES
1. DSP MODE DOES NOT IDENTIFY CHANNEL.
2. LRCLK NORMALLY OPERATES AT fS EXCEPT FOR DSP MODE WHICH IS 2 × fS.
3. BCLK FREQUENCY IS NORMALLY 64 × LRCLK BUT MAY BE OPERATED IN BURST MODE.
Figure 11. Stereo Serial Modes
tXBH
AUXBCLK
tXBL
tXLS
tXLH
AUXRCLK
tXDS
AUXDATA
LEFT JUSTIFIED
MODE
MSB
tXDH
MSB–1
tXDS
MSB
AUXDATA
2
I C JUSTIFIED
MODE
tXDH
tXDS
MSB
tXDS
LSB
AUXDATA
RIGHT JUSTIFIED
MODE
tXDH
tXDH
Figure 12. Auxiliary Serial Timing
Rev. 0 | Page 16 of 24
AD1974
tABH
ABCLK
tABL
tALS
tALH
ALRCLK
tABDD
ASDATA
LEFT JUSTIFIED
MODE
MSB
MSB–1
MSB
tABDD
ASDATA
I C JUSTIFIED
2
MODE
tABDD
ASDATA
RIGHT JUSTIFIED
MODE
MSB
LSB
Figure 13. ADC Serial Timing
Table 13. Pin Function Changes in TDM and AUX Modes (Replication of Table 12)
Pin Name
ASDATA1
ASDATA2
AUXDATA1
AUXDATA2
ALRCLK
ABCLK
AUXLRCLK
AUXBCLK
Stereo Mode
TDM Mode
AUX Mode
ADC1 data output
ADC2 data output
Not used (ground)
Not used (ground)
ADC LRCLK input/output
ADC BCLK input/output
Not used (ground)
Not used (ground)
ADC TDM data output
ADC TDM data input
Not used (ground)
ADCTDM data output
Not used (float)
AUXDATA in 1 (from external ADC1)
AUXDATA in 2 (from external ADC2)
ADCTDM frame sync input/output
ADCTDM BCLK input/output
AUXLRCLK input/output
Not used (ground)
ADC TDM Frame Sync input/output
ADC TDM BCLK input/output
Not used (ground)
Not used (ground)
AUXBCLK input/output
SHARC IS RUNNING
30MHz
IN SLAVE MODE
SHARC
(INTERRUPT-DRIVEN)
12.288MHz
LRCLK
BCLK
AUX
ADC 1
DATA
ASDATA1 ALRCLK ABCLK
MCLK
AUXBCLK
AUXLRCLK
AD1974
LRCLK
BCLK
AUX
AUXDATA1
AUXDATA2
MCLK
TDM MASTER
AUX MASTER
ADC 2
DATA
MCLK
Figure 14. Example of AUX Mode Connection to SHARC® (AD1974 as TDM Master/AUX Master Shown)
Rev. 0 | Page 17 of 24
AD1974
CONTROL REGISTERS
2
W
The format is the same for I C and SPI ports. The global address for the AD1974 is 0x04, shifted left one bit due to the R/ bit. All
registers are reset to 0.
Note that the first setting in each control register parameter is the default setting.
Table 14. Register Format
Global Address
R/W
Register Address
Data
23:17
16
15:8
7:0
Bit
Table 15. Register Addresses Description
Address
Function
0
1
2
3
4
5
PLL and Clock Control 0
PLL and Clock Control 1
AUXPORT Control 0
AUXPORT Control 1
AUXPORT Control 2
Reserved
6
Reserved
7
Reserved
8
Reserved
9
Reserved
10
11
12
13
14
15
16
Reserved
Reserved
Reserved
Reserved
ADC Control 0
ADC Control 1
ADC Control 2
PLL AND CLOCK CONTROL REGISTERS
Table 16. PLL and Clock Control 0
Bit
Value
Function
Description
0
0
1
Normal operation
Power-down
PLL power-down
2:1
4:3
6:5
7
00
01
10
11
00
01
10
11
00
01
10
11
0
INPUT 256 (×44.1 kHz or 48 kHz)
INPUT 384 (×44.1 kHz or 48 kHz)
INPUT 512 (×44.1 kHz or 48 kHz)
INPUT 768 (×44.1 kHz or 48 kHz)
XTAL oscillator enabled
256 × fS VCO output
512 × fS VCO output
Off
MCLKI/XI pin functionality (PLL active), master clock rate setting
MCLKO/XO pin, master clock rate setting
PLL input
MCLKI/XI
AUXLRCLK
ALRCLK
Reserved
Disable: ADC idle
Enable: ADC active
Internal MCLK enable
1
Rev. 0 | Page 18 of 24
AD1974
Table 17. PLL and Clock Control 1
Bit
Value
Function
PLL clock
MCLK
Description
0
0
1
AUXPORT clock source select
1
0
1
PLL clock
MCLK
ADC clock source select
2
0
1
Enabled
Disabled
Not locked
Locked
On-chip voltage reference
PLL lock indicator (read only)
3
0
1
7:4
0000
Reserved
AUXPORT CONTROL REGISTERS
Table 18. AUXPORT Control 0
Bit
Value
Function
Description
0
0
Reserved
Reserved
1
Reserved
2:1
5:3
00
01
10
11
32 kHz/44.1 kHz/48 kHz
64 kHz/88.2 kHz/96 kHz
128 kHz/176.4 kHz/192 kHz
Reserved
Sample rate
000
001
010
011
100
101
110
111
00
1
0
8
12
16
Reserved
Reserved
Reserved
AUXDATA delay (AUXBCLK periods)
7:6
Stereo (normal)
Serial format
01
Reserved
10
11
ADC AUX mode (ADC-, TDM-coupled)
Reserved
Table 19. AUXPORT Control 1
Bit
Value
Function
Reserved
Reserved
64 (two channels)
Reserved
Reserved
Reserved
Left low
Description
0
0
1
2:1
00
01
10
11
0
AUXBCLKs per frame
3
4
5
6
7
AUXLRCLK polarity
AUXLRCLK master/slave
AUXBCLK master/slave
AUXBCLK source
1
Left high
Slave
Master
0
1
0
1
Slave
Master
0
1
AUXBCLK pin
Internally generated
Normal
0
AUXBCLK polarity
1
Inverted
Rev. 0 | Page 19 of 24
AD1974
Table 20. AUXPORT Control 2
Bit
Value
Function
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
24
Description
0
0
1
2:1
4:3
00
01
10
11
00
01
10
11
0
Word width
20
Reserved
16
5
Reserved
Reserved
Reserved
1
7:6
00
ADC CONTROL REGISTERS
Table 21. ADC Control 0
Bit
Value
Function
Description
0
0
Normal
Power-down
1
Power down
1
0
1
Off
On
High-pass filter
ADC1L mute
2
0
Unmute
1
Mute
3
0
Unmute
ADC1R mute
1
Mute
4
0
Unmute
ADC2L mute
1
Mute
5
0
Unmute
ADC2R mute
1
Mute
7:6
00
01
10
11
32 kHz/44.1 kHz/48 kHz
64 kHz/88.2 kHz/96 kHz
128 kHz/176.4 kHz/192 kHz
Reserved
Output sample rate
Table 22. ADC Control 1
Bit
Value
Function
Description
1:0
00
24
Word width
01
20
10
Reserved
11
16
4:2
000
001
010
011
100
101
110
111
1
0
8
12
SDATA delay (BCLK periods)
16
Reserved
Reserved
Reserved
Rev. 0 | Page 20 of 24
AD1974
Bit
Value
00
01
10
11
0
Function
Description
6:5
Stereo
Serial format
TDM (daisy chain)
ADC AUX mode (TDM-coupled)
Reserved
7
Latch in midcycle (normal)
Latch in at end of cycle (pipeline)
BCLK active edge (TDM_IN)
1
Table 23. ADC Control 2
Bit
Value
Function
Description
0
0
50/50 (allows 32-/24-/20-/16-BCLK per channel)
LRCLK format
1
Pulse (32-BCLK/channel)
1
0
Drive out on falling edge (DEF)
BCLK polarity
1
Drive out on rising edge
2
0
1
Left low
Left high
Slave
Master
64
128
256
512
LRCLK polarity
LRCLK master/slave
BCLKs per frame
3
0
1
5:4
00
01
10
11
0
6
7
Slave
BCLK master/slave
BCLK source
1
Master
ABCLK pin
Internally generated
0
1
Rev. 0 | Page 21 of 24
AD1974
ADDITIONAL MODES
To relax the requirement for the setup time of the AD1974 in
cases of high speed TDM data transmission, the AD1974 can
latch in the data using the falling edge of ABCLK. This effec-
tively dedicates the entire BCLK period to the setup time. This
mode is useful in cases where the source has a large delay time
in the serial data driver. Figure 16 shows this pipeline mode of
data transmission.
The AD1974 offers several additional modes for board level
design enhancements. To reduce the EMI in board level design,
serial data can be transmitted without an explicit BCLK. See
Figure 15 for an example of an ADC TDM data transmission
mode that does not require high speed ABCLK. This configura-
tion is applicable when the AD1974 master clock is generated
by the PLL with the ALRCLK as the PLL reference frequency.
ALRCLK
32 BITS
INTERNAL
ABCLK
ASDATA2
ALRCLK
INTERNAL
ABCLK
ASDATA2
Figure 15. Serial ADC Data Transmission in TDM Format Without ABCLK
(Applicable Only If PLL Locks to ALRCLK)
ALRCLK
ABCLK
DATA MUST BE VALID
AT THIS BCLK EDGE
MSB
ASDATA1
Figure 16. I2S Pipeline Mode in ADC Serial Data Transmission
(Applicable in Stereo and TDM Useful for High Frequency TDM Transmission)
Rev. 0 | Page 22 of 24
AD1974
APPLICATION CIRCUITS
Typical applications circuits are shown in Figure 17 and Figure 18. Figure 17 shows a typical ADC input filter circuit. Recommended loop
filters for LR clock and master clock as the PLL reference are shown in Figure 18.
120pF
LRCLK
39nF
MCLK
5.6nF
600Z
LF
LF
5.76kΩ
5.76kΩ
AUDIO
INPUT
2
3
+
–
2.2nF
390pF
100pF
1
OP275
+
3.32kΩ
562Ω
AVDD2
AVDD2
4.7µF
+
5.76kΩ
237Ω
Figure 18. Recommended Loop Filters for LRCLK or MCLK PLL Reference
ADCxN
1nF
120pF
NPO
100pF
5.76kΩ
1nF
6
5
NPO
237Ω
–
4.7µF
+
7
OP275
+
ADCxP
Figure 17. Typical ADC Input Filter Circuit
Rev. 0 | Page 23 of 24
AD1974
OUTLINE DIMENSIONS
9.20
9.00 SQ
8.80
0.75
0.60
0.45
1.60
MAX
37
48
36
1
PIN 1
7.20
TOP VIEW
(PINS DOWN)
7.00 SQ
6.80
1.45
1.40
1.35
0.20
0.09
7°
3.5°
0°
0.08
COPLANARITY
25
12
0.15
0.05
13
24
SEATING
PLANE
0.27
0.22
0.17
VIEW A
0.50
BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BBC
Figure 19. 48-Lead Low Profile Quad Flat Package [LQFP]
(ST-48)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
–40°C to +105°C
–40°C to +105°C
Package Description
48-Lead LQFP
48-Lead LQFP, 13”Reel
Evaluation Board
Evaluation Board
Package Option
ST-48
ST-48
AD1974YSTZ1, 2
AD1974YSTZ-RL1, 2
EVAL-AD1974EB
EVAl-AD1974EBZ1
1 Z = RoHS Compliant Part.
2 Single-ended output; SPI control port.
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06614-0-4/07(0)
Rev. 0 | Page 24 of 24
相关型号:
©2020 ICPDF网 联系我们和版权申明