AT45DB081D-SSU-2.5_技术文档

Features

• Single 2.5V or 2.7V to 3.6V Supply

• RapidS Serial Interface: 66MHz Maximum Clock Frequency

– SPI Compatible Modes 0 and 3

• User Configurable Page Size

– 256-Bytes per Page

– 264-Bytes per Page

– Page Size Can Be Factory Pre-configured for 256-Bytes

• Page Program Operation

– Intelligent Programming Operation

– 4,096 Pages (256/264-Bytes/Page) Main Memory

• Flexible Erase Options

8-megabit

2.5V or 2.7V

DataFlash

– Page Erase (256-Bytes)

– Block Erase (2-Kbytes)

– Sector Erase (64-Kbytes)

– Chip Erase (8Mbits)

AT45DB081D

• Two SRAM Data Buffers (256-/264-Bytes)

– Allows Receiving of Data while Reprogramming the Flash Array

• Continuous Read Capability through Entire Array

– Ideal for Code Shadowing Applications

• Low-power Dissipation

– 7mA Active Read Current Typical

– 25μA Standby Current Typical

– 15μA Deep Power Down Typical

• Hardware and Software Data Protection Features

– Individual Sector

• Sector Lockdown for Secure Code and Data Storage

– Individual Sector

• Security: 128-byte Security Register

– 64-byte User Programmable Space

– Unique 64-byte Device Identifier

• JEDEC Standard Manufacturer and Device ID Read

• 100,000 Program/Erase Cycles Per Page Minimum

• Data Retention – 20 Years

• Industrial Temperature Range

• Green (Pb/Halide-free/RoHS Compliant) Packaging Options

1. Description

The Adesto^®AT45DB081D is a 2.5V or 2.7V, serial-interface Flash memory

ideally suited for a wide variety of digital voice-, image-, program code- and data-stor-

age applications. The AT45DB081D supports RapidS^™serial interface for

applications requiring very high speed operations. RapidS serial interface is SPI com-

patible for frequencies up to 66MHz. Its 8,650,752-bits of memory are organized as

4,096 pages of 256-bytes or 264-bytes each. In addition to the main memory, the

AT45DB081D also contains two SRAM buffers of 256-/264-bytes each. The buffers

allow the receiving of data while a page in the main Memory is being reprogrammed,

as well as writing a continuous data stream. EEPROM emulation (bit or byte alterabil-

ity) is easily handled with a self-contained three step read-modify-write operation.

Unlike conventional Flash memories that are accessed randomly with multiple

3596O–DFLASH–1/2013

address lines and a parallel interface, the Adesto^™DataFlash^®uses a RapidS serial interface to

sequentially access its data. The simple sequential access dramatically reduces active pin

count, facilitates hardware layout, increases system reliability, minimizes switching noise, and

reduces package size. The device is optimized for use in many commercial and industrial appli-

cations where high-density, low-pin count, low-voltage and low-power are essential.

To allow for simple in-system reprogrammability, the AT45DB081D does not require high input

voltages for programming. The device operates from a single power supply, 2.5V to 3.6V or 2.7V

to 3.6V, for both the program and read operations. The AT45DB081D is enabled through the

chip select pin (CS) and accessed via a three-wire interface consisting of the Serial Input (SI),

Serial Output (SO), and the Serial Clock (SCK).

All programming and erase cycles are self-timed.

2. Pin Configurations and Pinouts

Figure 2-1. MLF (VDFN) Top View

SI

SCK

1

2

3

4

8

7

6

5

SO

GND

VCC

WP

RESET

CS

Figure 2-2. SOIC Top View

SI

SCK

1

2

3

4

8

SO

7

6

5

GND

RESET

CS

VCC

WP

Note:

1. The metal pad on the bottom of the MLF package is floating. This pad can be a “No Connect”

or connected to GND

2

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

Table 2-1.

Symbol

Pin Configurations

Asserted

State

Name and Function

Type

Chip Select: Asserting the CS pin selects the device. When the CS pin is deasserted, the device

will be deselected and normally be placed in the standby mode (not Deep Power-Down mode),

and the output pin (SO) will be in a high-impedance state. When the device is deselected, data

will not be accepted on the input pin (SI).

CS

Low

Input

A high-to-low transition on the CS pin is required to start an operation, and a low-to-high

transition is required to end an operation. When ending an internally self-timed operation such as

a program or erase cycle, the device will not enter the standby mode until the completion of the

operation.

Serial Clock: This pin is used to provide a clock to the device and is used to control the flow of

data to and from the device. Command, address, and input data present on the SI pin is always

latched on the rising edge of SCK, while output data on the SO pin is always clocked out on the

falling edge of SCK.

SCK

–

Input

Serial Input: The SI pin is used to shift data into the device. The SI pin is used for all data input

including command and address sequences. Data on the SI pin is always latched on the rising

edge of SCK.

SI

–

Input

Serial Output: The SO pin is used to shift data out from the device. Data on the SO pin is always

clocked out on the falling edge of SCK.

SO

Output

Write Protect: When the WP pin is asserted, all sectors specified for protection by the Sector

Protection Register will be protected against program and erase operations regardless of

whether the Enable Sector Protection command has been issued or not. The WP pin functions

independently of the software controlled protection method. After the WP pin goes low, the

content of the Sector Protection Register cannot be modified.

If a program or erase command is issued to the device while the WP pin is asserted, the device

will simply ignore the command and perform no operation. The device will return to the idle state

once the CS pin has been deasserted. The Enable Sector Protection command and Sector

Lockdown command, however, will be recognized by the device when the WP pin is asserted.

WP

Low

Input

The WP pin is internally pulled-high and may be left floating if hardware controlled protection will

not be used. However, it is recommended that the WP pin also be externally connected to V_CC

whenever possible.

Reset: A low state on the reset pin (RESET) will terminate the operation in progress and reset

the internal state machine to an idle state. The device will remain in the reset condition as long as

a low level is present on the RESET pin. Normal operation can resume once the RESET pin is

brought back to a high level.

RESET

Low

Input

The device incorporates an internal power-on reset circuit, so there are no restrictions on the

RESET pin during power-on sequences. If this pin and feature are not utilized it is recommended

that the RESET pin be driven high externally.

Device Power Supply: The V_CCpin is used to supply the source voltage to the device.

V_CC

–

Power

Operations at invalid V_CCvoltages may produce spurious results and should not be attempted.

Ground: The ground reference for the power supply. GND should be connected to the system

ground.

GND

Ground

3

3596O–DFLASH–1/2013

3. Block Diagram

WP

FLASH MEMORY ARRAY

PAGE (256-/264-BYTES)

BUFFER 1 (256-/264-BYTES)

BUFFER 2 (256-/264-BYTES)

SCK

CS

I/O INTERFACE

RESET

VCC

GND

SI

SO

4. Memory Array

To provide optimal flexibility, the memory array of the AT45DB081D is divided into three levels of granularity comprising of

sectors, blocks, and pages. The “Memory Architecture Diagram” illustrates the breakdown of each level and details the

number of pages per sector and block. All program operations to the DataFlash occur on a page by page basis. The erase

operations can be performed at the chip, sector, block or page level.

Figure 4-1. Memory Architecture Diagram

SECTOR ARCHITECTURE

BLOCK ARCHITECTURE

PAGE ARCHITECTURE

BLOCK 0

BLOCK 1

BLOCK 2

8 Pages

PAGE 0

PAGE 1

SECTOR 0a

SECTOR 0a = 8 Pages

2,048 / 2,112-bytes

SECTOR 0b = 248 Pages

63,488 / 65,472-bytes

PAGE 6

PAGE 7

PAGE 8

PAGE 9

BLOCK 30

BLOCK 31

BLOCK 32

BLOCK 33

SECTOR 1 = 256 Pages

65,536 / 67,584-bytes

SECTOR 2 = 256 Pages

65,536 / 67,584-bytes

PAGE 14

PAGE 15

PAGE 16

PAGE 17

PAGE 18

BLOCK 62

BLOCK 63

BLOCK 64

BLOCK 65

SECTOR 14 = 256 Pages

65,536 / 67,584-bytes

SECTOR 15 = 256 Pages

65,536 / 67,584-bytes

BLOCK 510

BLOCK 511

PAGE 4,094

PAGE 4,095

Block = 2,048 / 2,112-bytes

Page = 256 / 264-bytes

4

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

5. Device Operation

The device operation is controlled by instructions from the host processor. The list of instructions

and their associated opcodes are contained in Table 15-1 on page 27 through Table 15-7 on

page 30. A valid instruction starts with the falling edge of CS followed by the appropriate 8-bit

opcode and the desired buffer or main memory address location. While the CS pin is low, tog-

gling the SCK pin controls the loading of the opcode and the desired buffer or main memory

address location through the SI (serial input) pin. All instructions, addresses, and data are trans-

ferred with the most significant bit (MSB) first.

Buffer addressing for the DataFlash standard page size (264-bytes) is referenced in the data-

sheet using the terminology BFA8 - BFA0 to denote the nine address bits required to designate

a byte address within a buffer. Main memory addressing is referenced using the terminology

PA11 - PA0 and BA8 - BA0, where PA11 - PA0 denotes the 12 address bits required to desig-

nate a page address and BA8 - BA0 denotes the nine address bits required to designate a byte

address within the page.

For “Power of 2” binary page size (256-bytes) the Buffer addressing is referenced in the data-

sheet using the conventional terminology BFA7 - BFA0 to denote the eight address bits required

to designate a byte address within a buffer. Main memory addressing is referenced using the

terminology A19 - A0, where A19 - A8 denotes the 12 address bits required to designate a page

address and A7 - A0 denotes the eight address bits required to designate a byte address within

a page.

6. Read Commands

By specifying the appropriate opcode, data can be read from the main memory or from either

one of the two SRAM data buffers. The DataFlash supports RapidS protocols for Mode 0 and

Mode 3. Please refer to the “Detailed Bit-level Read Timing” diagrams in this datasheet for

details on the clock cycle sequences for each mode.

6.1

Continuous Array Read (Legacy Command: E8H): Up to 66MHz

By supplying an initial starting address for the main memory array, the Continuous Array Read

command can be utilized to sequentially read a continuous stream of data from the device by

simply providing a clock signal; no additional addressing information or control signals need to

be provided. The DataFlash incorporates an internal address counter that will automatically

increment on every clock cycle, allowing one continuous read operation without the need of

additional address sequences. To perform a continuous read from the DataFlash standard page

size (264-bytes), an opcode of E8H must be clocked into the device followed by three address

bytes (which comprise the 24-bit page and byte address sequence) and four don’t care bytes.

The first 12 bits (PA11 - PA0) of the 21-bit address sequence specify which page of the main

memory array to read, and the last nine bits (BA8 - BA0) of the 21-bit address sequence specify

the starting byte address within the page. To perform a continuous read from the binary page

size (256-bytes), the opcode (E8H) must be clocked into the device followed by three address

bytes and four don’t care bytes. The first 12 bits (A19 - A8) of the 20-bits sequence specify which

page of the main memory array to read, and the last eight bits (A7 - A0) of the 20-bits address

sequence specify the starting byte address within the page. The don’t care bytes that follow the

address bytes are needed to initialize the read operation. Following the don’t care bytes, addi-

tional clock pulses on the SCK pin will result in data being output on the SO (serial output) pin.

The CS pin must remain low during the loading of the opcode, the address bytes, the don’t care

bytes, and the reading of data. When the end of a page in main memory is reached during a

5

3596O–DFLASH–1/2013

Continuous Array Read, the device will continue reading at the beginning of the next page with

no delays incurred during the page boundary crossover (the crossover from the end of one page

to the beginning of the next page). When the last bit in the main memory array has been read,

the device will continue reading back at the beginning of the first page of memory. As with cross-

ing over page boundaries, no delays will be incurred when wrapping around from the end of the

array to the beginning of the array.

A low-to-high transition on the CS pin will terminate the read operation and tri-state the output

pin (SO). The maximum SCK frequency allowable for the Continuous Array Read is defined by

the f_CAR1specification. The Continuous Array Read bypasses both data buffers and leaves the

contents of the buffers unchanged.

6.2

Continuous Array Read (High Frequency Mode: 0BH): Up to 66MHz

This command can be used with the serial interface to read the main memory array sequentially

in high speed mode for any clock frequency up to the maximum specified by f_CAR1. To perform a

continuous read array with the page size set to 264-bytes, the CS must first be asserted then an

opcode 0BH must be clocked into the device followed by three address bytes and a dummy

byte. The first 12 bits (PA11 - PA0) of the 21-bit address sequence specify which page of the

main memory array to read, and the last nine bits (BA8 - BA0) of the 21-bit address sequence

specify the starting byte address within the page. To perform a continuous read with the page

size set to 256-bytes, the opcode, 0BH, must be clocked into the device followed by three

address bytes (A19 - A0) and a dummy byte. Following the dummy byte, additional clock pulses

on the SCK pin will result in data being output on the SO (serial output) pin.

The CS pin must remain low during the loading of the opcode, the address bytes, and the read-

ing of data. When the end of a page in the main memory is reached during a Continuous Array

Read, the device will continue reading at the beginning of the next page with no delays incurred

during the page boundary crossover (the crossover from the end of one page to the beginning of

the next page). When the last bit in the main memory array has been read, the device will con-

tinue reading back at the beginning of the first page of memory. As with crossing over page

boundaries, no delays will be incurred when wrapping around from the end of the array to the

beginning of the array. A low-to-high transition on the CS pin will terminate the read operation

and tri-state the output pin (SO). The maximum SCK frequency allowable for the Continuous

Array Read is defined by the f_CAR1specification. The Continuous Array Read bypasses both

data buffers and leaves the contents of the buffers unchanged.

6.3

Continuous Array Read (Low Frequency Mode: 03H): Up to 33MHz

This command can be used with the serial interface to read the main memory array sequentially

without a dummy byte up to maximum frequencies specified by f_CAR2. To perform a continuous

read array with the page size set to 264-bytes, the CS must first be asserted then an opcode,

03H, must be clocked into the device followed by three address bytes (which comprise the 24-bit

page and byte address sequence). The first 12 bits (PA11 - PA0) of the 21-bit address sequence

specify which page of the main memory array to read, and the last nine bits (BA8 - BA0) of the

21-bit address sequence specify the starting byte address within the page. To perform a contin-

uous read with the page size set to 256-bytes, the opcode, 03H, must be clocked into the device

followed by three address bytes (A19 - A0). Following the address bytes, additional clock pulses

on the SCK pin will result in data being output on the SO (serial output) pin.

The CS pin must remain low during the loading of the opcode, the address bytes, and the read-

ing of data. When the end of a page in the main memory is reached during a Continuous Array

Read, the device will continue reading at the beginning of the next page with no delays incurred

6

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

during the page boundary crossover (the crossover from the end of one page to the beginning of

the next page). When the last bit in the main memory array has been read, the device will con-

tinue reading back at the beginning of the first page of memory. As with crossing over page

boundaries, no delays will be incurred when wrapping around from the end of the array to the

beginning of the array. A low-to-high transition on the CS pin will terminate the read operation

and tri-state the output pin (SO). The Continuous Array Read bypasses both data buffers and

leaves the contents of the buffers unchanged.

6.4

Main Memory Page Read

A main memory page read allows the user to read data directly from any one of the 4,096 pages

in the main memory, bypassing both of the data buffers and leaving the contents of the buffers

unchanged. To start a page read from the DataFlash standard page size (264-bytes), an opcode

of D2H must be clocked into the device followed by three address bytes (which comprise the

24-bit page and byte address sequence) and four don’t care bytes. The first 12 bits (PA11 -

PA0) of the 21-bit address sequence specify the page in main memory to be read, and the last

nine bits (BA8 - BA0) of the 21-bit address sequence specify the starting byte address within

that page. To start a page read from the binary page size (256-bytes), the opcode D2H must be

clocked into the device followed by three address bytes and four don’t care bytes. The first 12

bits (A19 - A8) of the 20-bits sequence specify which page of the main memory array to read,

and the last eight bits (A7 - A0) of the 20-bits address sequence specify the starting byte

address within the page. The don’t care bytes that follow the address bytes are sent to initialize

the read operation. Following the don’t care bytes, additional pulses on SCK result in data being

output on the SO (serial output) pin. The CS pin must remain low during the loading of the

opcode, the address bytes, the don’t care bytes, and the reading of data. When the end of a

page in main memory is reached, the device will continue reading back at the beginning of the

same page. A low-to-high transition on the CS pin will terminate the read operation and tri-state

the output pin (SO). The maximum SCK frequency allowable for the Main Memory Page Read is

defined by the f_SCKspecification. The Main Memory Page Read bypasses both data buffers and

leaves the contents of the buffers unchanged.

6.5

Buffer Read

The SRAM data buffers can be accessed independently from the main memory array, and utiliz-

ing the Buffer Read Command allows data to be sequentially read directly from the buffers. Four

opcodes, D4H or D1H for buffer 1 and D6H or D3H for buffer 2 can be used for the Buffer Read

Command. The use of each opcode depends on the maximum SCK frequency that will be used

to read data from the buffer. The D4H and D6H opcode can be used at any SCK frequency up to

the maximum specified by f_CAR1. The D1H and D3H opcode can be used for lower frequency

read operations up to the maximum specified by f_CAR2

.

To perform a buffer read from the standard DataFlash buffer (264-bytes), the opcode must be

clocked into the device followed by three address bytes comprised of 15 don’t care bits and

nine buffer address bits (BFA8 - BFA0). To perform a buffer read from the binary buffer (256-

bytes), the opcode must be clocked into the device followed by three address bytes comprised

of 16 don’t care bits and eight buffer address bits (BFA7 - BFA0). Following the address bytes,

one don’t care byte must be clocked in to initialize the read operation. The CS pin must remain

low during the loading of the opcode, the address bytes, the don’t care bytes, and the reading of

data. When the end of a buffer is reached, the device will continue reading back at the beginning

of the buffer. A low-to-high transition on the CS pin will terminate the read operation and tri-state

the output pin (SO).

7

3596O–DFLASH–1/2013

7. Program and Erase Commands

7.1

Buffer Write

Data can be clocked in from the input pin (SI) into either buffer 1 or buffer 2. To load data into the

standard DataFlash buffer (264-bytes), a 1-byte opcode, 84H for buffer 1 or 87H for buffer 2,

must be clocked into the device, followed by three address bytes comprised of 15 don’t care bits

and nine buffer address bits (BFA8 - BFA0). The nine buffer address bits specify the first byte in

the buffer to be written. To load data into the binary buffers (256-bytes each), a 1-byte opcode

84H for buffer 1 or 87H for buffer 2, must be clocked into the device, followed by three address

bytes comprised of 16 don’t care bits and eight buffer address bits (BFA7 - BFA0). The eight buf-

fer address bits specify the first byte in the buffer to be written. After the last address byte has

been clocked into the device, data can then be clocked in on subsequent clock cycles. If the end

of the data buffer is reached, the device will wrap around back to the beginning of the buffer.

Data will continue to be loaded into the buffer until a low-to-high transition is detected on the CS

pin.

7.2

Buffer to Main Memory Page Program with Built-in Erase

Data written into either buffer 1 or buffer 2 can be programmed into the main memory. A 1-byte

opcode, 83H for buffer 1 or 86H for buffer 2, must be clocked into the device. For the DataFlash

standard page size (264-bytes), the opcode must be followed by three address bytes consist of

three don’t care bits, 12 page address bits (PA11 - PA0) that specify the page in the main mem-

ory to be written and nine don’t care bits. To perform a buffer to main memory page program

with built-in erase for the binary page size (256-bytes), the opcode 83H for buffer 1 or 86H for

buffer 2, must be clocked into the device followed by three address bytes consisting of four don’t

care bits 12 page address bits (A19 - A8) that specify the page in the main memory to be written

and eight don’t care bits. When a low-to-high transition occurs on the CS pin, the part will first

erase the selected page in main memory (the erased state is a logic 1) and then program the

data stored in the buffer into the specified page in main memory. Both the erase and the pro-

gramming of the page are internally self-timed and should take place in a maximum time of t_EP.

During this time, the status register will indicate that the part is busy.

7.3

Buffer to Main Memory Page Program without Built-in Erase

A previously-erased page within main memory can be programmed with the contents of either

buffer 1 or buffer 2. A 1-byte opcode, 88H for buffer 1 or 89H for buffer 2, must be clocked into

the device. For the DataFlash standard page size (264-bytes), the opcode must be followed by

three address bytes consist of three don’t care bits, 12 page address bits (PA11 - PA0) that

specify the page in the main memory to be written and nine don’t care bits. To perform a buffer

to main memory page program without built-in erase for the binary page size (256-bytes), the

opcode 88H for buffer 1 or 89H for buffer 2, must be clocked into the device followed by three

address bytes consisting of four don’t care bits, 12 page address bits (A19 - A8) that specify the

page in the main memory to be written and eight don’t care bits. When a low-to-high transition

occurs on the CS pin, the part will program the data stored in the buffer into the specified page in

the main memory. It is necessary that the page in main memory that is being programmed has

been previously erased using one of the erase commands (Page Erase or Block Erase). The

programming of the page is internally self-timed and should take place in a maximum time of t_P.

During this time, the status register will indicate that the part is busy.

8

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

7.4

Page Erase

The Page Erase command can be used to individually erase any page in the main memory array

allowing the Buffer to Main Memory Page Program to be utilized at a later time. To perform a

page erase in the DataFlash standard page size (264-bytes), an opcode of 81H must be loaded

into the device, followed by three address bytes comprised of three don’t care bits, 12 page

address bits (PA11 - PA0) that specify the page in the main memory to be erased and nine don’t

care bits. To perform a page erase in the binary page size (256-bytes), the opcode 81H must be

loaded into the device, followed by three address bytes consist of four don’t care bits, 12 page

address bits (A19 - A8) that specify the page in the main memory to be erased and eight don’t

care bits. When a low-to-high transition occurs on the CS pin, the part will erase the selected

page (the erased state is a logical 1). The erase operation is internally self-timed and should

take place in a maximum time of t_PE. During this time, the status register will indicate that the

part is busy.

7.5

Block Erase

A block of eight pages can be erased at one time. This command is useful when large amounts

of data has to be written into the device. This will avoid using multiple Page Erase Commands.

To perform a block erase for the DataFlash standard page size (264-bytes), an opcode of 50H

must be loaded into the device, followed by three address bytes comprised of three don’t care

bits, nine page address bits (PA11 -PA3) and 12 don’t care bits. The nine page address bits are

used to specify which block of eight pages is to be erased. To perform a block erase for the

binary page size (256-bytes), the opcode 50H must be loaded into the device, followed by three

address bytes consisting of four don’t care bits, nine page address bits (A19 - A11) and 11 don’t

care bits. The nine page address bits are used to specify which block of eight pages is to be

erased. When a low-to-high transition occurs on the CS pin, the part will erase the selected

block of eight pages. The erase operation is internally self-timed and should take place in a max-

imum time of t_BE. During this time, the status register will indicate that the part is busy.

Table 7-1.

Block Erase Addressing

PA11/

A19

PA10/

A18

PA9/

A17

PA8/

A16

PA7/

A15

PA6/

A14

PA5/

A13

PA4/

A12

PA3/

A11

PA2/

A10

PA1/

A9

PA0/

A8

Block

0

1

0

1

0

1

X

0

1

2

3

•

1

0

1

0

1

0

1

X

508

509

510

511

9

3596O–DFLASH–1/2013

7.6

Sector Erase

The Sector Erase command can be used to individually erase any sector in the main memory.

There are 16 sectors and only one sector can be erased at one time. To perform sector 0a or

sector 0b erase for the DataFlash standard page size (264-bytes), an opcode of 7CH must be

loaded into the device, followed by three address bytes comprised of three don’t care bits, nine

page address bits (PA11 - PA3) and 12 don’t care bits. To perform a sector 1-15 erase, the

opcode 7CH must be loaded into the device, followed by three address bytes comprised of

three don’t care bits, four page address bits (PA11 - PA8) and 17 don’t care bits. To perform

sector 0a or sector 0b erase for the binary page size (256-bytes), an opcode of 7CH must be

loaded into the device, followed by three address bytes comprised of four don’t care bit and nine

page address bits (A19 - A11) and 11 don’t care bits. To perform a sector 1-15 erase, the

opcode 7CH must be loaded into the device, followed by three address bytes comprised of four

don’t care bit and four page address bits (A19 - A16) and 16 don’t care bits. The page address

bits are used to specify any valid address location within the sector which is to be erased. When

a low-to-high transition occurs on the CS pin, the part will erase the selected sector. The erase

operation is internally self-timed and should take place in a maximum time of t_SE. During this

time, the status register will indicate that the part is busy.

Table 7-2.

Sector Erase Addressing

PA11/

A19

PA10/

A18

PA9/

A17

PA8/

A16

PA7/

A15

PA6/

A14

PA5/

A13

PA4/

A12

PA3/

A11

PA2/

A10

PA1/

A9

PA0/

A8

Sector

0

1

0

1

0

1

X

0a

0b

1

X

2

•

1

0

1

0

1

0

1

X

12

13

14

15

7.7

Chip Erase

The entire main memory can be erased at one time by using the Chip Erase command.

To execute the Chip Erase command, a 4-byte command sequence C7H, 94H, 80H and 9AH

must be clocked into the device. Since the entire memory array is to be erased, no address

bytes need to be clocked into the device, and any data clocked in after the opcode will be

ignored. After the last bit of the opcode sequence has been clocked in, the CS pin can be deas-

serted to start the erase process. The erase operation is internally self-timed and should take

place in a time of t_CE. During this time, the Status Register will indicate that the device is busy.

The Chip Erase command will not affect sectors that are protected or locked down; the contents

of those sectors will remain unchanged. Only those sectors that are not protected or locked

down will be erased.

10

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

The WP pin can be asserted while the device is erasing, but protection will not be activated until

the internal erase cycle completes.

Table 7-3.

Chip Erase Command

Command

Byte 1

Byte 2

Byte 3

Byte 4

Chip Erase

C7H

94H

80H

9AH

Figure 7-1. Chip Erase

CS

Opcode

Byte 1

Opcode

Byte 2

Opcode

Byte 3

Opcode

Byte 4

SI

Each transition

represents 8 bits

Note:

Refer to errata regarding Chip Erase on page 52.

7.8

Main Memory Page Program Through Buffer

This operation is a combination of the Buffer Write and Buffer to Main Memory Page Program

with Built-in Erase operations. Data is first clocked into buffer 1 or buffer 2 from the input pin (SI)

and then programmed into a specified page in the main memory. To perform a main memory

page program through buffer for the DataFlash standard page size (264-bytes), a 1-byte

opcode, 82H for buffer 1 or 85H for buffer 2, must first be clocked into the device, followed by

three address bytes. The address bytes are comprised of three don’t care bits, 12 page address

bits, (PA11 - PA0) that select the page in the main memory where data is to be written, and nine

buffer address bits (BFA8 - BFA0) that select the first byte in the buffer to be written. To perform

a main memory page program through buffer for the binary page size (256-bytes), the opcode

82H for buffer 1 or 85H for buffer 2, must be clocked into the device followed by three address

bytes consisting of four don’t care bits, 12 page address bits (A19 - A8) that specify the page in

the main memory to be written, and eight buffer address bits (BFA7 - BFA0) that selects the first

byte in the buffer to be written. After all address bytes are clocked in, the part will take data from

the input pins and store it in the specified data buffer. If the end of the buffer is reached, the

device will wrap around back to the beginning of the buffer. When there is a low-to-high transi-

tion on the CS pin, the part will first erase the selected page in main memory to all 1s and then

program the data stored in the buffer into that memory page. Both the erase and the program-

ming of the page are internally self-timed and should take place in a maximum time of t_EP

During this time, the status register will indicate that the part is busy.

.

8. Sector Protection

Two protection methods, hardware and software controlled, are provided for protection against

inadvertent or erroneous program and erase cycles. The software controlled method relies on

the use of software commands to enable and disable sector protection while the hardware con-

trolled method employs the use of the Write Protect (WP) pin. The selection of which sectors

that are to be protected or unprotected against program and erase operations is specified in the

nonvolatile Sector Protection Register. The status of whether or not sector protection has been

enabled or disabled by either the software or the hardware controlled methods can be deter-

mined by checking the Status Register.

11

3596O–DFLASH–1/2013

8.1

Software Sector Protection

8.1.1

Enable Sector Protection Command

Sectors specified for protection in the Sector Protection Register can be protected from program

and erase operations by issuing the Enable Sector Protection command. To enable the sector

protection using the software controlled method, the CS pin must first be asserted as it would be

with any other command. Once the CS pin has been asserted, the appropriate 4-byte command

sequence must be clocked in via the input pin (SI). After the last bit of the command sequence

has been clocked in, the CS pin must be deasserted after which the sector protection will be

enabled.

Table 8-1.

Command

Enable Sector Protection Command

Byte 1

Byte 2

Byte 3

Byte 4

Enable Sector Protection

3DH

2AH

7FH

A9H

Figure 8-1. Enable Sector Protection

CS

Opcode

Byte 1

Opcode

Byte 2

Opcode

Byte 3

Opcode

Byte 4

SI

Each transition

represents 8 bits

8.1.2

Disable Sector Protection Command

To disable the sector protection using the software controlled method, the CS pin must first be

asserted as it would be with any other command. Once the CS pin has been asserted, the

appropriate 4-byte sequence for the Disable Sector Protection command must be clocked in via

the input pin (SI). After the last bit of the command sequence has been clocked in, the CS pin

must be deasserted after which the sector protection will be disabled. The WP pin must be in the

deasserted state; otherwise, the Disable Sector Protection command will be ignored.

Table 8-2.

Command

Disenable Sector Protection Command

Byte 1

Byte 2

Byte 3

Byte 4

Disable Sector Protection

3DH

2AH

7FH

9AH

Figure 8-2. Disable Sector Protection

CS

Opcode

Byte 1

Opcode

Byte 2

Opcode

Byte 3

Opcode

Byte 4

SI

Each transition

represents 8 bits

8.1.3

Various Aspects About Software Controlled Protection

Software controlled protection is useful in applications in which the WP pin is not or cannot be

controlled by a host processor. In such instances, the WP pin may be left floating (the WP pin is

internally pulled high) and sector protection can be controlled using the Enable Sector Protection

and Disable Sector Protection commands.

12

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

If the device is power cycled, then the software controlled protection will be disabled. Once the

device is powered up, the Enable Sector Protection command should be reissued if sector pro-

tection is desired and if the WP pin is not used.

9. Hardware Controlled Protection

Sectors specified for protection in the Sector Protection Register and the Sector Protection Reg-

ister itself can be protected from program and erase operations by asserting the WP pin and

keeping the pin in its asserted state. The Sector Protection Register and any sector specified for

protection cannot be erased or reprogrammed as long as the WP pin is asserted. In order to

modify the Sector Protection Register, the WP pin must be deasserted. If the WP pin is perma-

nently connected to GND, then the content of the Sector Protection Register cannot be changed.

If the WP pin is deasserted, or permanently connected to V_CC, then the content of the Sector

Protection Register can be modified.

The WP pin will override the software controlled protection method but only for protecting the

sectors. For example, if the sectors were not previously protected by the Enable Sector Protec-

tion command, then simply asserting the WP pin would enable the sector protection within the

maximum specified t_WPEtime. When the WP pin is deasserted; however, the sector protection

would no longer be enabled (after the maximum specified t_WPDtime) as long as the Enable Sec-

tor Protection command was not issued while the WP pin was asserted. If the Enable Sector

Protection command was issued before or while the WP pin was asserted, then simply deassert-

ing the WP pin would not disable the sector protection. In this case, the Disable Sector

Protection command would need to be issued while the WP pin is deasserted to disable the sec-

tor protection. The Disable Sector Protection command is also ignored whenever the WP pin is

asserted.

A noise filter is incorporated to help protect against spurious noise that may inadvertently assert

or deassert the WP pin.

The table below details the sector protection status for various scenarios of the WP pin, the

Enable Sector Protection command, and the Disable Sector Protection command.

Figure 9-1. WP Pin and Protection Status

1

2

3

WP

Table 9-1.

WP Pin and Protection Status

Sector

Protection

Register

Time

Period

Enable Sector Protection

Disable Sector

Protection Command

Sector Protection

Status

WP Pin

High

Command

Command Not Issued Previously

X

Disabled

Enabled

Read/Write

1

2

–

Issue Command

–

Issue Command

Low

X

Enabled

Read Only

Command Issued During Period 1

or 2

Not Issued Yet

Issue Command

–

Enabled

Disabled

Enabled

Read/Write

3

High

–

Issue Command

13

3596O–DFLASH–1/2013

9.1

Sector Protection Register

The nonvolatile Sector Protection Register specifies which sectors are to be protected or unpro-

tected with either the software or hardware controlled protection methods. The Sector Protection

Register contains 16-bytes of data, of which byte locations 0 through 15 contain values that

specify whether sectors 0 through 15 will be protected or unprotected. The Sector Protection

Register is user modifiable and must first be erased before it can be reprogrammed. Table 9-3

illustrates the format of the Sector Protection Register.:

Table 9-2.

Sector Protection Register

Sector Number

Protected

0 (0a, 0b)

1 to 15

FFH

See Table 9-3

Unprotected

00H

Table 9-3.

Sector 0 (0a, 0b)

0a

(Page 0-7)

Bit 7, 6

00

0b

(Page 8-255)

Data

Value

Bit 5, 4

00

Bit 3, 2

xx

Bit 1, 0

xx

Sectors 0a, 0b Unprotected

Protect Sector 0a

0xH

CxH

3xH

11

00

xx

Protect Sector 0b (Page 8-255)

00

11

xx

Protect Sectors 0a (Page 0-7), 0b

(Page 8-255)⁽¹⁾

11

xx

FxH

Note:

1. The default value for bytes 0 through 15 when shipped from Adesto is 00H

x = don’t care

9.1.1

Erase Sector Protection Register Command

In order to modify and change the values of the Sector Protection Register, it must first be

erased using the Erase Sector Protection Register command.

To erase the Sector Protection Register, the CS pin must first be asserted as it would be with

any other command. Once the CS pin has been asserted, the appropriate 4-byte opcode

sequence must be clocked into the device via the SI pin. The 4-byte opcode sequence must

start with 3DH and be followed by 2AH, 7FH, and CFH. After the last bit of the opcode sequence

has been clocked in, the CS pin must be deasserted to initiate the internally self-timed erase

cycle. The erasing of the Sector Protection Register should take place in a time of t_PE, during

which time the Status Register will indicate that the device is busy. If the device is powered-

down before the completion of the erase cycle, then the contents of the Sector Protection Regis-

ter cannot be guaranteed.

The Sector Protection Register can be erased with the sector protection enabled or disabled.

Since the erased state (FFH) of each byte in the Sector Protection Register is used to indicate

that a sector is specified for protection, leaving the sector protection enabled during the erasing

of the register allows the protection scheme to be more effective in the prevention of accidental

programming or erasing of the device. If for some reason an erroneous program or erase com-

mand is sent to the device immediately after erasing the Sector Protection Register and before

the register can be reprogrammed, then the erroneous program or erase command will not be

processed because all sectors would be protected.

14

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

Table 9-4.

Erase Sector Protection Register Command

Command

Byte 1

Byte 2

2AH

Byte 3

Byte 4

Erase Sector Protection Register

3DH

7FH

CFH

Figure 9-2. Erase Sector Protection Register

CS

Opcode

Byte 1

Opcode

Byte 2

Opcode

Byte 3

Opcode

Byte 4

SI

Each transition

represents 8 bits

9.1.2

Program Sector Protection Register Command

Once the Sector Protection Register has been erased, it can be reprogrammed using the Pro-

gram Sector Protection Register command.

To program the Sector Protection Register, the CS pin must first be asserted and the appropri-

ate 4-byte opcode sequence must be clocked into the device via the SI pin. The 4-byte opcode

sequence must start with 3DH and be followed by 2AH, 7FH, and FCH. After the last bit of the

opcode sequence has been clocked into the device, the data for the contents of the Sector

Protection Register must be clocked in. As described in Section 9.1, the Sector Protection Reg-

ister contains 16-bytes of data, so 16-bytes must be clocked into the device. The first byte of

data corresponds to sector zero, the second byte corresponds to sector one, and so on with the

last byte of data corresponding to sector 15.

After the last data byte has been clocked in, the CS pin must be deasserted to initiate the inter-

nally self-timed program cycle. The programming of the Sector Protection Register should take

place in a time of t_P, during which time the Status Register will indicate that the device is busy. If

the device is powered-down during the program cycle, then the contents of the Sector Protection

Register cannot be guaranteed.

If the proper number of data bytes is not clocked in before the CS pin is deasserted, then the

protection status of the sectors corresponding to the bytes not clocked in can not be guaranteed.

For example, if only the first two bytes are clocked in instead of the complete 16-bytes, then the

protection status of the last 14 sectors cannot be guaranteed. Furthermore, if more than 16-

bytes of data is clocked into the device, then the data will wrap back around to the beginning of

the register. For instance, if 17-bytes of data are clocked in, then the 17^thbyte will be stored at

byte location zero of the Sector Protection Register.

If a value other than 00H or FFH is clocked into a byte location of the Sector Protection Register,

then the protection status of the sector corresponding to that byte location cannot be guaran-

teed. For example, if a value of 17H is clocked into byte location two of the Sector Protection

Register, then the protection status of sector two cannot be guaranteed.

The Sector Protection Register can be reprogrammed while the sector protection enabled or dis-

abled. Being able to reprogram the Sector Protection Register with the sector protection enabled

allows the user to temporarily disable the sector protection to an individual sector rather than dis-

abling sector protection completely.

The Program Sector Protection Register command utilizes the internal SRAM buffer 1 for pro-

cessing. Therefore, the contents of the buffer 1 will be altered from its previous state when this

command is issued.

15

3596O–DFLASH–1/2013

Table 9-5.

Program Sector Protection Register Command

Command

Byte 1

Byte 2

2AH

Byte 3

Byte 4

Program Sector Protection Register

3DH

7FH

FCH

Figure 9-3. Program Sector Protection Register

CS

SI

Opcode

Byte 1

Opcode

Byte 2

Opcode

Byte 3

Opcode

Byte 4

Data Byte

n

Data Byte

n + 1

Data Byte

n + 15

Each transition

represents 8 bits

9.1.3

Read Sector Protection Register Command

To read the Sector Protection Register, the CS pin must first be asserted. Once the CS pin has

been asserted, an opcode of 32H and three dummy bytes must be clocked in via the SI pin. After

the last bit of the opcode and dummy bytes have been clocked in, any additional clock pulses on

the SCK pins will result in data for the content of the Sector Protection Register being output on

the SO pin. The first byte corresponds to sector 0 (0a, 0b), the second byte corresponds to sec-

tor one and the last byte (byte 16) corresponds to sector 15. Once the last byte of the Sector

Protection Register has been clocked out, any additional clock pulses will result in undefined

data being output on the SO pin. The CS must be deasserted to terminate the Read Sector Pro-

tection Register operation and put the output into a high-impedance state.

Table 9-6.

Read Sector Protection Register Command

Command

Byte 1

Byte 2

xxH

Byte 3

Byte 4

Read Sector Protection Register

32H

xxH

Note:

xx = Dummy Byte

Figure 9-4. Read Sector Protection Register

CS

Opcode

X

SI

Data Byte

n

Data Byte

n + 1

Data Byte

n + 15

SO

Each transition

represents 8 bits

9.1.4

Various Aspects About the Sector Protection Register

The Sector Protection Register is subject to a limit of 10,000 erase/program cycles. Users are

encouraged to carefully evaluate the number of times the Sector Protection Register will be

modified during the course of the applications’ life cycle. If the application requires that the Sec-

tor Protection Register be modified more than the specified limit of 10,000 cycles because the

application needs to temporarily unprotect individual sectors (sector protection remains enabled

while the Sector Protection Register is reprogrammed), then the application will need to limit this

practice. Instead, a combination of temporarily unprotecting individual sectors along with dis-

abling sector protection completely will need to be implemented by the application to ensure that

the limit of 10,000 cycles is not exceeded.

16

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

10. Security Features

10.1 Sector Lockdown

The device incorporates a Sector Lockdown mechanism that allows each individual sector to be

permanently locked so that it becomes read only. This is useful for applications that require the

ability to permanently protect a number of sectors against malicious attempts at altering program

code or security information. Once a sector is locked down, it can never be erased or pro-

grammed, and it can never be unlocked.

To issue the Sector Lockdown command, the CS pin must first be asserted as it would be for

any other command. Once the CS pin has been asserted, the appropriate 4-byte opcode

sequence must be clocked into the device in the correct order. The 4-byte opcode sequence

must start with 3DH and be followed by 2AH, 7FH, and 30H. After the last byte of the command

sequence has been clocked in, then three address bytes specifying any address within the sec-

tor to be locked down must be clocked into the device. After the last address bit has been

clocked in, the CS pin must then be deasserted to initiate the internally self-timed lockdown

sequence.

The lockdown sequence should take place in a maximum time of t_P, during which time the Status

Register will indicate that the device is busy. If the device is powered-down before the comple-

tion of the lockdown sequence, then the lockdown status of the sector cannot be guaranteed. In

this case, it is recommended that the user read the Sector Lockdown Register to determine the

status of the appropriate sector lockdown bits or bytes and reissue the Sector Lockdown com-

mand if necessary.

Table 10-1. Sector Lockdown

Command

Byte 1

Byte 2

Byte 3

Byte 4

Sector Lockdown

3DH

2AH

7FH

30H

Figure 10-1. Sector Lockdown

CS

SI

Address

Bytes

Opcode

Byte 1

Opcode

Byte 2

Opcode

Byte 3

Opcode

Byte 4

Address

Bytes

Address

Bytes

Each transition

represents 8 bits

17

3596O–DFLASH–1/2013

10.1.1

Sector Lockdown Register

Sector Lockdown Register is a nonvolatile register that contains 16-bytes of data, as shown

below:

Table 10-2. Sector Lockdown Register

Sector Number

Locked

0 (0a, 0b)

1 to 15

FFH

See Below

Unlocked

00H

Table 10-3. Sector 0 (0a, 0b)

0a

0b

(Page 0-7)

(Page 8-255)

Data

Value

Bit 7, 6

00

Bit 5, 4

00

Bit 3, 2

00

Bit 1, 0

00

Sectors 0a, 0b Unlocked

00H

C0H

30H

F0H

Sector 0a Locked (Page 0-7)

Sector 0b Locked (Page 8-255)

Sectors 0a, 0b Locked (Page 0-255)

11

00

11

00

11

00

10.1.2

Reading the Sector Lockdown Register

The Sector Lockdown Register can be read to determine which sectors in the memory array are

permanently locked down. To read the Sector Lockdown Register, the CS pin must first be

asserted. Once the CS pin has been asserted, an opcode of 35H and three dummy bytes must

be clocked into the device via the SI pin. After the last bit of the opcode and dummy bytes have

been clocked in, the data for the contents of the Sector Lockdown Register will be clocked out

on the SO pin. The first byte corresponds to sector 0 (0a, 0b) the second byte corresponds to

sector one and the las byte (byte 16) corresponds to sector 15. After the last byte of the Sector

Lockdown Register has been read, additional pulses on the SCK pin will simply result in unde-

fined data being output on the SO pin.

Deasserting the CS pin will terminate the Read Sector Lockdown Register operation and put the

SO pin into a high-impedance state.

Table 10-4 details the values read from the Sector Lockdown Register.

Table 10-4. Sector Lockdown Register

Command

Byte 1

Byte 2

Byte 3

Byte 4

Read Sector Lockdown Register

35H

xxH

Note:

xx = Dummy Byte

Figure 10-2. Read Sector Lockdown Register

CS

Opcode

X

SI

Data Byte

n + 1

Data Byte

n + 15

SO

n

Each transition

represents 8 bits

18

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

10.2 Security Register

The device contains a specialized Security Register that can be used for purposes such as

unique device serialization or locked key storage. The register is comprised of a total of 128-

bytes that is divided into two portions. The first 64-bytes (byte locations 0 through 63) of the

Security Register are allocated as a one-time user programmable space. Once these 64-bytes

have been programmed, they cannot be reprogrammed. The remaining 64-bytes of the register

(byte locations 64 through 127) are factory programmed by Adesto and will contain a unique

value for each device. The factory programmed data is fixed and cannot be changed.

Table 10-5. Security Register

Security Register Byte Number

0

1



62

63

64

65



126

127

Data Type

One-time User Programmable

Factory Programmed by Adesto

10.2.1

Programming the Security Register

The user programmable portion of the Security Register does not need to be erased before it is

programmed.

To program the Security Register, the CS pin must first be asserted and the appropriate 4-byte

opcode sequence must be clocked into the device in the correct order. The 4-byte opcode

sequence must start with 9BH and be followed by 00H, 00H, and 00H. After the last bit of the

opcode sequence has been clocked into the device, the data for the contents of the 64-byte user

programmable portion of the Security Register must be clocked in.

After the last data byte has been clocked in, the CS pin must be deasserted to initiate the inter-

nally self-timed program cycle. The programming of the Security Register should take place in a

time of t_P, during which time the Status Register will indicate that the device is busy. If the device

is powered-down during the program cycle, then the contents of the 64-byte user programmable

portion of the Security Register cannot be guaranteed.

If the full 64-bytes of data is not clocked in before the CS pin is deasserted, then the values of

the byte locations not clocked in cannot be guaranteed. For example, if only the first two bytes

are clocked in instead of the complete 64-bytes, then the remaining 62-bytes of the user pro-

grammable portion of the Security Register cannot be guaranteed. Furthermore, if more than 64-

bytes of data is clocked into the device, then the data will wrap back around to the beginning of

the register. For instance, if 65-bytes of data are clocked in, then the 65^thbyte will be stored at

byte location 0 of the Security Register.

The user programmable portion of the Security Register can only be programmed one

time. Therefore, it is not possible to only program the first two bytes of the register and then pro-

gram the remaining 62-bytes at a later time.

The Program Security Register command utilizes the internal SRAM buffer 1 for processing.

Therefore, the contents of the buffer 1 will be altered from its previous state when this command

is issued.

Figure 10-3. Program Security Register

CS

Opcode

Byte 1

Opcode

Byte 2

Opcode

Byte 3

Opcode

Byte 4

Data Byte

n

Data Byte

n + 1

Data Byte

n + 63

SI

Each transition

represents 8 bits

19

3596O–DFLASH–1/2013

10.2.2

Reading the Security Register

The Security Register can be read by first asserting the CS pin and then clocking in an opcode

of 77H followed by three dummy bytes. After the last don’t care bit has been clocked in, the con-

tent of the Security Register can be clocked out on the SO pin. After the last byte of the Security

Register has been read, additional pulses on the SCK pin will simply result in undefined data

being output on the SO pins.

Deasserting the CS pin will terminate the Read Security Register operation and put the SO pin

into a high-impedance state.

Figure 10-4. Read Security Register

CS

SI

Opcode

X

Data Byte

n

Data Byte

n + 1

Data Byte

n + x

SO

Each transition

represents 8 bits

11. Additional Commands

11.1 Main Memory Page to Buffer Transfer

A page of data can be transferred from the main memory to either buffer 1 or buffer 2. To start

the operation for the DataFlash standard page size (264-bytes), a 1-byte opcode, 53H for buffer

1 and 55H for buffer 2, must be clocked into the device, followed by three address bytes com-

prised of three don’t care bits, 12 page address bits (PA11 - PA0), which specify the page in

main memory that is to be transferred, and nine don’t care bits. To perform a main memory page

to buffer transfer for the binary page size (256-bytes), the opcode 53H for buffer 1 or 55H for buf-

fer 2, must be clocked into the device followed by three address bytes consisting of four don’t

care bits, 12 page address bits (A19 - A8) which specify the page in the main memory that is to

be transferred, and eight don’t care bits. The CS pin must be low while toggling the SCK pin to

load the opcode and the address bytes from the input pin (SI). The transfer of the page of data

from the main memory to the buffer will begin when the CS pin transitions from a low to a high

state. During the transfer of a page of data (t_XFR), the status register can be read to determine

whether the transfer has been completed.

11.2 Main Memory Page to Buffer Compare

A page of data in main memory can be compared to the data in buffer 1 or buffer 2. To initiate

the operation for DataFlash standard page size, a 1-byte opcode, 60H for buffer 1 and 61H for

buffer 2, must be clocked into the device, followed by three address bytes consisting of three

don’t care bits, 12 page address bits (PA11 - PA0) that specify the page in the main memory that

is to be compared to the buffer, and nine don’t care bits. To start a main memory page to buffer

compare for a binary page size, the opcode 60H for buffer 1 or 61H for buffer 2, must be clocked

into the device followed by three address bytes consisting of four don’t care bits, 12 page

address bits (A19 - A8) that specify the page in the main memory that is to be compared to the

buffer, and eight don’t care bits. The CS pin must be low while toggling the SCK pin to load the

opcode and the address bytes from the input pin (SI). On the low-to-high transition of the CS pin,

the data bytes in the selected main memory page will be compared with the data bytes in buffer

1 or buffer 2. During this time (t_COMP), the status register will indicate that the part is busy. On

20

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

completion of the compare operation, bit six of the status register is updated with the result of

the compare.

11.3 Auto Page Rewrite

This mode is only needed if multiple bytes within a page or multiple pages of data are modified in

a random fashion within a sector. This mode is a combination of two operations: Main Memory

Page to Buffer Transfer and Buffer to Main Memory Page Program with Built-in Erase. A page of

data is first transferred from the main memory to buffer 1 or buffer 2, and then the same data

(from buffer 1 or buffer 2) is programmed back into its original page of main memory. To start the

rewrite operation for the DataFlash standard page size (264-bytes), a 1-byte opcode, 58H for

buffer 1 or 59H for buffer 2, must be clocked into the device, followed by three address bytes

comprised of three don’t care bits, 12 page address bits (PA11-PA0) that specify the page in

main memory to be rewritten and nine don’t care bits. To initiate an auto page rewrite for a

binary page size (256-bytes), the opcode 58H for buffer 1 or 59H for buffer 2, must be clocked

into the device followed by three address bytes consisting of four don’t care bits, 12 page

address bits (A19 - A8) that specify the page in the main memory that is to be written and eight

don’t care bits. When a low-to-high transition occurs on the CS pin, the part will first transfer data

from the page in main memory to a buffer and then program the data from the buffer back into

same page of main memory. The operation is internally self-timed and should take place in a

maximum time of t_EP. During this time, the status register will indicate that the part is busy.

If a sector is programmed or reprogrammed sequentially page by page, then the programming

algorithm shown in Figure 25-1 (page 45) is recommended. Otherwise, if multiple bytes in a

page or several pages are programmed randomly in a sector, then the programming algorithm

shown in Figure 25-2 (page 46) is recommended. Each page within a sector must be

updated/rewritten at least once within every 20,000 cumulative page erase/program operations

in that sector. Please contact Adesto for availability of devices that are specified to exceed the

20K cycle cumulative limit.

11.4 Status Register Read

The status register can be used to determine the device’s ready/busy status, page size, a Main

Memory Page to Buffer Compare operation result, the Sector Protection status or the device

density. The Status Register can be read at any time, including during an internally self-timed

program or erase operation. To read the status register, the CS pin must be asserted and the

opcode of D7H must be loaded into the device. After the opcode is clocked in, the 1-byte status

register will be clocked out on the output pin (SO), starting with the next clock cycle. The data in

the status register, starting with the MSB (bit 7), will be clocked out on the SO pin during the next

eight clock cycles. After the one byte of the status register has been clocked out, the sequence

will repeat itself (as long as CS remains low and SCK is being toggled). The data in the status

register is constantly updated, so each repeating sequence will output new data.

Ready/busy status is indicated using bit seven of the status register. If bit seven is a one, then

the device is not busy and is ready to accept the next command. If bit seven is a zero, then the

device is in a busy state. Since the data in the status register is constantly updated, the user

must toggle SCK pin to check the ready/busy status. There are several operations that can

cause the device to be in a busy state: Main Memory Page to Buffer Transfer, Main Memory

Page to Buffer Compare, Buffer to Main Memory Page Program, Main Memory Page Program

through Buffer, Page Erase, Block Erase, Sector Erase, Chip Erase and Auto Page Rewrite.

21

3596O–DFLASH–1/2013

The result of the most recent Main Memory Page to Buffer Compare operation is indicated using

bit six of the status register. If bit six is a zero, then the data in the main memory page matches

the data in the buffer. If bit six is a one, then at least one bit of the data in the main memory page

does not match the data in the buffer.

Bit one in the Status Register is used to provide information to the user whether or not the sector

protection has been enabled or disabled, either by software-controlled method or hardware-con-

trolled method. A logic one indicates that sector protection has been enabled and logic zero

indicates that sector protection has been disabled.

Bit zero in the Status Register indicates whether the page size of the main memory array is con-

figured for “power of 2” binary page size (256-bytes) or the DataFlash standard page size (264-

bytes). If bit zero is a one, then the page size is set to 256-bytes. If bit zero is a zero, then the

page size is set to 264-bytes.

The device density is indicated using bits five, four, three, and two of the status register. For the

Adesto AT45DB081D, the four bits are 1001 The decimal value of these four binary bits does not

equate to the device density; the four bits represent a combinational code relating to differing

densities of DataFlash devices. The device density is not the same as the density code indicated

in the JEDEC device ID information. The device density is provided only for backward

compatibility.

Table 11-1. Status Register Format

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

RDY/BUSY

COMP

1

0

1

PROTECT

PAGE SIZE

12. Deep Power-down

After initial power-up, the device will default in standby mode. The Deep Power-down command

allows the device to enter into the lowest power consumption mode. To enter the Deep Power-

down mode, the CS pin must first be asserted. Once the CS pin has been asserted, an opcode

of B9H command must be clocked in via input pin (SI). After the last bit of the command has

been clocked in, the CS pin must be de-asserted to initiate the Deep Power-down operation.

After the CS pin is de-asserted, the will device enter the Deep Power-down mode within the

maximum t_EDPDtime. Once the device has entered the Deep Power-down mode, all instructions

are ignored except for the Resume from Deep Power-down command.

Table 12-1. Deep Power-down

Command

Opcode

Deep Power-down

B9H

Figure 12-1. Deep Power-down

CS

SI

Opcode

Each transition

represents 8 bits

22

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

12.1 Resume from Deep Power-down

The Resume from Deep Power-down command takes the device out of the Deep Power-down

mode and returns it to the normal standby mode. To Resume from Deep Power-down mode, the

CS pin must first be asserted and an opcode of ABH command must be clocked in via input pin

(SI). After the last bit of the command has been clocked in, the CS pin must be de-asserted to

terminate the Deep Power-down mode. After the CS pin is de-asserted, the device will return to

the normal standby mode within the maximum t_RDPDtime. The CS pin must remain high during

the t_RDPDtime before the device can receive any commands. After resuming form Deep Power-

down, the device will return to the normal standby mode.

Table 12-2. Resume from Deep Power-down

Command

Opcode

Resume from Deep Power-down

ABH

Figure 12-2. Resume from Deep Power-Down

CS

Opcode

SI

Each transition

represents 8 bits

13. “Power of 2” Binary Page Size Option

“Power of 2” binary page size Configuration Register is a user-programmable nonvolatile regis-

ter that allows the page size of the main memory to be configured for binary page size (256-

bytes) or DataFlash standard page size (264-bytes). The “power of 2” page size is a one-time

programmable configuration register and once the device is configured for “power of 2”

page size, it cannot be reconfigured again. The devices are initially shipped with the page

size set to 264-bytes. The user has the option of ordering binary page size (256-bytes) devices

from the factory. For details, please refer to Section 26. ”Ordering Information” on page 47.

For the binary “power of 2” page size to become effective, the following steps must be followed:

1. Program the one-time programmable configuration resister using opcode sequence

3DH, 2AH, 80H and A6H (please see Section 13.1).

2. Power cycle the device (i.e. power down and power up again).

3. User can now program the page for the binary page size.

If the above steps are not followed in setting the the page size prior to page programming, user

may expect incorrect data during a read operation.

The address format will be changed after the device is configured for “power of 2” page size.

See Section 21.7 ”Command Sequence for Read/Write Operations for Page Size 256-Bytes

(Except Status Register Read, Manufacturer and Device ID Read)” on page 38.

23

3596O–DFLASH–1/2013

13.1 Programming the Configuration Register

To program the Configuration Register for “power of 2” binary page size, the CS pin must first be

asserted as it would be with any other command. Once the CS pin has been asserted, the

appropriate 4-byte opcode sequence must be clocked into the device in the correct order. The

4-byte opcode sequence must start with 3DH and be followed by 2AH, 80H, and A6H. After the

last bit of the opcode sequence has been clocked in, the CS pin must be deasserted to initiate

the internally self-timed program cycle. The programming of the Configuration Register should

take place in a time of t_P, during which time the Status Register will indicate that the device is

busy. The device must be power-cycled after the completion of the program cycle to set the

“power of 2” page size. If the device is powered-down before the completion of the program

cycle, then setting the Configuration Register cannot be guaranteed. However, the user should

check bit zero of the status register to see whether the page size was configured for binary page

size. If not, the command can be re-issued again.

Table 13-1. Programming the Configuration Register

Command

Byte 1

Byte 2

Byte 3

Byte 4

Power of Two Page Size

3DH

2AH

80H

A6H

Figure 13-1. Program Configuration Register

CS

Opcode

Byte 1

Opcode

Byte 2

Opcode

Byte 3

Opcode

Byte 4

SI

Each transition

represents 8 bits

14. Manufacturer and Device ID Read

Identification information can be read from the device to enable systems to electronically query

and identify the device while it is in system. The identification method and the command opcode

comply with the JEDEC standard for “Manufacturer and Device ID Read Methodology for SPI

Compatible Serial Interface Memory Devices”. The type of information that can be read from the

device includes the JEDEC defined Manufacturer ID, the vendor specific Device ID, and the ven-

dor specific Extended Device Information.

To read the identification information, the CS pin must first be asserted and the opcode of 9FH

must be clocked into the device. After the opcode has been clocked in, the device will begin out-

putting the identification data on the SO pin during the subsequent clock cycles. The first byte

that will be output will be the Manufacturer ID followed by two bytes of Device ID information.

The fourth byte output will be the Extended Device Information String Length, which will be 00H

indicating that no Extended Device Information follows. As indicated in the JEDEC standard,

reading the Extended Device Information String Length and any subsequent data is optional.

Deasserting the CS pin will terminate the Manufacturer and Device ID Read operation and put

the SO pin into a high-impedance state. The CS pin can be deasserted at any time and does not

require that a full byte of data be read.

24

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

14.1 Manufacturer and Device ID Information

14.1.1

Byte 1 – Manufacturer ID

JEDEC Assigned Code

Hex

Value

Bit 7

0

Bit 6

0

Bit 5

0

Bit 4

1

Bit 3

1

Bit 2

1

Bit 1

1

Bit 0

1

1FH

Manufacturer ID

1FH = Adesto

14.1.2

Byte 2 – Device ID (Part 1)

Family Code

Density Code

Hex

Value

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Family Code

001 = DataFlash

00101 = 8-Mbit

25H

0

1

0

1

0

1

Density Code

14.1.3

Byte 3 – Device ID (Part 2)

MLC Code

Product Version Code

Hex

Value

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

MLC Code

000 = 1-bit/Cell Technology

00000 = Initial Version

00H

0

Product Version

14.1.4

Byte 4 – Extended Device Information String Length

Byte Count

Hex

Value

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

00H

0

Byte Count

00H = 0 Bytes of Information

CS

9FH

Opcode

SI

1FH

25H

00H

Data

SO

Manufacturer ID

Byte n

Device ID

Byte 1

Device ID

Byte 2

Extended

Device

Information

String Length

Extended

Device

Information

Byte x

Extended

Device

Information

Byte x + 1

Each transition

represents 8 bits

This information would only be output

if the Extended Device Information String Length

value was something other than 00H.

Note:

Based on JEDEC publication 106 (JEP106), Manufacturer ID data can be comprised of any number of bytes. Some manufacturers may have

Manufacturer ID codes that are two, three or even four bytes long with the first byte(s) in the sequence being 7FH. A system should detect code

7FH as a “Continuation Code” and continue to read Manufacturer ID bytes. The first non-7FH byte would signify the last byte of Manufacturer ID

data. For Adesto (and some other manufacturers), the Manufacturer ID data is comprised of only one byte.

25

3596O–DFLASH–1/2013

14.2 Operation Mode Summary

The commands described previously can be grouped into four different categories to better

describe which commands can be executed at what times.

Group A commands consist of:

1. Main Memory Page Read

2. Continuous Array Read

3. Read Sector Protection Register

4. Read Sector Lockdown Register

5. Read Security Register

Group B commands consist of:

1. Page Erase

2. Block Erase

3. Sector Erase

4. Chip Erase

5. Main Memory Page to Buffer 1 (or 2) Transfer

6. Main Memory Page to Buffer 1 (or 2) Compare

7. Buffer 1 (or 2) to Main Memory Page Program with Built-in Erase

8. Buffer 1 (or 2) to Main Memory Page Program without Built-in Erase

9. Main Memory Page Program through Buffer 1 (or 2)

10. Auto Page Rewrite

Group C commands consist of:

1. Buffer 1 (or 2) Read

2. Buffer 1 (or 2) Write

3. Status Register Read

4. Manufacturer and Device ID Read

Group D commands consist of:

1. Erase Sector Protection Register

2. Program Sector Protection Register

3. Sector Lockdown

4. Program Security Register

If a Group A command is in progress (not fully completed), then another command in Group A,

B, C, or D should not be started. However, during the internally self-timed portion of Group B

commands, any command in Group C can be executed. The Group B commands using buffer 1

should use Group C commands using buffer 2 and vice versa. Finally, during the internally self-

timed portion of a Group D command, only the Status Register Read command should be

executed.

26

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

15. Command Tables

Table 15-1. Read Commands

Command

Opcode

D2H

E8H

Main Memory Page Read

Continuous Array Read (Legacy Command)

Continuous Array Read (Low Frequency)

Continuous Array Read (High Frequency)

Buffer 1 Read (Low Frequency)

Buffer 2 Read (Low Frequency)

Buffer 1 Read

03H

0BH

D1H

D3H

D4H

D6H

Buffer 2 Read

Table 15-2. Program and Erase Commands

Command

Opcode

Buffer 1 Write

84H

Buffer 2 Write

87H

Buffer 1 to Main Memory Page Program with Built-in Erase

Buffer 2 to Main Memory Page Program with Built-in Erase

Buffer 1 to Main Memory Page Program without Built-in Erase

Buffer 2 to Main Memory Page Program without Built-in Erase

Page Erase

83H

86H

88H

89H

81H

Block Erase

50H

Sector Erase

7CH

Chip Erase

C7H, 94H, 80H, 9AH

Main Memory Page Program Through Buffer 1

Main Memory Page Program Through Buffer 2

82H

85H

Table 15-3. Protection and Security Commands

Command

Opcode

Enable Sector Protection

Disable Sector Protection

Erase Sector Protection Register

Program Sector Protection Register

Read Sector Protection Register

Sector Lockdown

3DH + 2AH + 7FH + A9H

3DH + 2AH + 7FH + 9AH

3DH + 2AH + 7FH + CFH

3DH + 2AH + 7FH + FCH

32H

3DH + 2AH + 7FH + 30H

27

3596O–DFLASH–1/2013

Table 15-3. Protection and Security Commands

Command

Opcode

Read Sector Lockdown Register

Program Security Register

Read Security Register

35H

9BH + 00H + 00H + 00H

77H

Table 15-4. Additional Commands

Command

Opcode

53H

Main Memory Page to Buffer 1 Transfer

Main Memory Page to Buffer 2 Transfer

Main Memory Page to Buffer 1 Compare

Main Memory Page to Buffer 2 Compare

Auto Page Rewrite through Buffer 1

Auto Page Rewrite through Buffer 2

Deep Power-down

55H

60H

61H

58H

59H

B9H

ABH

D7H

9FH

Resume from Deep Power-down

Status Register Read

Manufacturer and Device ID Read

Table 15-5. Legacy Commands⁽¹⁾

Command

Opcode

54H

Buffer 1 Read

Buffer 2 Read

56H

Main Memory Page Read

Continuous Array Read

Status Register Read

52H

68H

57H

Note:

1. These legacy commands are not recommended for new designs

28

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

Table 15-6. Detailed Bit-level Addressing Sequence for Binary Page Size (256-Bytes)

Page Size = 256-bytes

Address Byte

Additional

Don’t Care

Bytes

Opcode

N/A

1

03h

0Bh

50h

53h

55h

58h

59h

60h

61h

77h

7Ch

81h

82h

83h

84h

85h

86h

87h

88h

89h

9Fh

B9h

ABh

D1h

D2h

D3h

D4h

D6h

D7h

E8h

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

N/A

4

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

N/A

x

N/A

x

N/A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

x

A

N/A

1

x

1

x

N/A

4

N/A

x

N/A

x

A

Notes: x = Don’t Care

29

3596O–DFLASH–1/2013

Table 15-7. Detailed Bit-level Addressing Sequence for the DataFlash Standard Page Size (264-Bytes)

Page Size = 264-bytes

Address Byte

Additional

Don’t Care

Bytes

Opcode

N/A

1

03h

0Bh

50h

53h

55h

58h

59h

60h

61h

77h

7Ch

81h

82h

83h

84h

85h

86h

87h

88h

89h

9Fh

B9h

ABh

D1h

D2h

D3h

D4h

D6h

D7h

E8h

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

N/A

4

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

B

x

P

x

N/A

x

N/A

x

N/A

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

P

x

B

x

P

x

P

x

B

N/A

1

x

1

x

N/A

4

N/A

x

N/A

x

P

B

Notes: P = Page Address Bit

B = Byte/Buffer Address Bit

x = Don’t Care

30

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

16. Power-on/Reset State

When power is first applied to the device, or when recovering from a reset condition, the device

will default to Mode 3. In addition, the output pin (SO) will be in a high impedance state, and a

high-to-low transition on the CS pin will be required to start a valid instruction. The mode (Mode

3 or Mode 0) will be automatically selected on every falling edge of CS by sampling the inactive

clock state.

16.1 Initial Power-up/Reset Timing Restrictions

At power up, the device must not be selected until the supply voltage reaches the V_CC(min.) and

further delay of t_VCSL. During power-up, the internal Power-on Reset circuitry keeps the device in

reset mode until the V_CCrises above the Power-on Reset threshold value (V_POR). At this time, all

operations are disabled and the device does not respond to any commands. After power up is

applied and the V_CCis at the minimum operating voltage V_CC(min.), the t_VCSLdelay is required

before the device can be selected in order to perform a read operation.

Similarly, the t_PUWdelay is required after the V_CCrises above the Power-on Reset threshold

value (V_POR) before the device can perform a write (Program or Erase) operation. After initial

power-up, the device will default in Standby mode.

Table 16-1. Initial Power-up/Reset Timing Restrictions

Symbol

t_VCSL

Parameter

Min

Typ

Max

Units

μs

V_CC(min.) to Chip Select low

Power-Up Device Delay before Write Allowed

Power-ON Reset Voltage

70

t_PUW

20

ms

V

V_POR

1.5

2.5

17. System Considerations

The RapidS serial interface is controlled by the clock SCK, serial input SI and chip select CS

pins. These signals must rise and fall monotonically and be free from noise. Excessive noise or

ringing on these pins can be misinterpreted as multiple edges and cause improper operation of

the device. The PC board traces must be kept to a minimum distance or appropriately termi-

nated to ensure proper operation. If necessary, decoupling capacitors can be added on these

pins to provide filtering against noise glitches.

As system complexity continues to increase, voltage regulation is becoming more important. A

key element of any voltage regulation scheme is its current sourcing capability. Like all Flash

memories, the peak current for DataFlash occur during the programming and erase operation.

The regulator needs to supply this peak current requirement. An under specified regulator can

cause current starvation. Besides increasing system noise, current starvation during program-

ming or erase can lead to improper operation and possible data corruption.

31

3596O–DFLASH–1/2013

18. Electrical Specifications

Table 18-1. Absolute Maximum Ratings*

*NOTICE:

Stresses beyond those listed under “Absolute

Maximum Ratings” may cause permanent dam-

age to the device. The "Absolute Maximum Rat-

ings" are stress ratings only and functional

operation of the device at these or any other con-

ditions beyond those indicated in the operational

sections of this specification is not implied. Expo-

sure to absolute maximum rating conditions for

extended periods may affect device reliability.

Voltage Extremes referenced in the "Absolute

Maximum Ratings" are intended to accommo-

date short duration undershoot/overshoot condi-

tions and does not imply or guarantee functional

device operation at these levels for any extended

period of time

Temperature under Bias ................................ -55C to +125C

Storage Temperature..................................... -65C to +150C

All Input Voltages (except V_CCbut including NC pins)

with Respect to Ground ...................................-0.6V to +6.25V

All Output Voltages

with Respect to Ground .............................-0.6V to V_CC+ 0.6V

Table 18-2. DC and AC Operating Range

AT45DB081D (2.5V Version)

-40C to 85C

AT45DB081D

-40C to 85C

2.7V to 3.6V

Operating Temperature (Case)

V_CCPower Supply

Ind.

2.5V to 3.6V

Note:

1. After power is applied and V_CCis at the minimum specified datasheet value, the system should wait 10 ms before an opera-

tional mode is started

32

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

Table 18-3. DC Characteristics

Symbol

Parameter

Condition

Min

Typ

Max

Units

CS, RESET, WP = V_IH, all

inputs at CMOS levels

I_DP

Deep Power-down Current

15

25

μA

CS, RESET, WP = V_IH, all

inputs at CMOS levels

I_SB

Standby Current

25

7

50

10

12

14

15

17

μA

mA

f = 20MHz; I_OUT= 0mA;

V_CC= 3.6V

f = 33MHz; I_OUT= 0mA;

8

V_CC= 3.6V

Active Current, Read

Operation

(1)

I_CC1

f = 50MHz; I_OUT= 0mA;

10

11

12

V_CC= 3.6V

f = 66MHz; I_OUT= 0mA;

V

_CC= 3.6V

Active Current, Program/Erase

Operation

I_CC2

V

I_LI

Input Load Current

Output Leakage Current

Input Low Voltage

V_IN= CMOS levels

V_I/O= CMOS levels

1

μA

V

I_LO

V_IL

V_IH

V_OL

V_OH

V_CCx 0.3

Input High Voltage

Output Low Voltage

Output High Voltage

V_CCx 0.7

V

I_OL= 1.6mA; V_CC= 2.7V

0.4

V

I_OH= -100μA

V_CC- 0.2V

V

Notes: 1. I_CC1during a buffer read is 20mA maximum @ 20MHz

2. All inputs (SI, SCK, CS#, WP#, and RESET#) are guaranteed by design to be 5V tolerant

33

3596O–DFLASH–1/2013

Table 18-4. AC Characteristics – RapidS/Serial Interface

AT45DB081D

(2.5V Version)

AT45DB081D

Typ

Symbol

f_SCK

Parameter

Min

Typ

Max

50

Min

Max

66

Units

MHz

SCK Frequency

f_CAR1

SCK Frequency for Continuous Array Read

50

66

SCK Frequency for Continuous Array Read

(Low Frequency)

f_CAR2

33

MHz

t_WH

t_WL

SCK High Time

6.8

0.1

50

5

6.8

0.1

50

5

ns

SCK Low Time

(1)

t_SCKR

SCK Rise Time, Peak-to-Peak (Slew Rate)

SCK Fall Time, Peak-to-Peak (Slew Rate)

Minimum CS High Time

CS Setup Time

V/ns

ns

(1)

t_SCKF

t_CS

t_CSS

t_CSH

t_SU

ns

CS Hold Time

5

ns

Data In Setup Time

2

ns

t_H

Data In Hold Time

3

ns

t_HO

Output Hold Time

0

ns

t_DIS

t_V

Output Disable Time

27

35

8

27

35

6

ns

Output Valid

ns

t_WPE

t_WPD

t_EDPD

t_RDPD

t_XFR

t_comp

WP Low to Protection Enabled

WP High to Protection Disabled

CS High to Deep Power-down Mode

CS High to Standby Mode

Page to Buffer Transfer Time

Page to Buffer Compare Time

1

μs

1

μs

3

μs

35

200

35

200

μs

Page Erase and Programming Time

(256-/264-bytes)

t_EP

14

35

14

35

ms

t_P

Page Programming Time (256-/264-bytes)

Page Erase Time (256-/264-bytes)

Block Erase Time (2,048-/2,112-bytes)

Sector Erase Time (65,536/67,584)

Chip Erase Time

2

13

30

0.7

7

4

2

13

30

0.7

7

4

ms

s

t_PE

t_BE

t_SE

t_CE

t_RST

t_REC

32

75

1.3

22

32

75

1.3

22

s

RESET Pulse Width

10

μs

RESET Recovery Time

1

34

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

19. Input Test Waveforms and Measurement Levels

2.4V

AC

DRIVING

LEVELS

1.5V

MEASUREMENT

LEVEL

0.45V

t_R, t_F< 2 ns (10% to 90%)

20. Output Test Load

DEVICE

UNDER

TEST

30pF

21. AC Waveforms

Six different timing waveforms are shown on page 36. Waveform 1 shows the SCK signal being

low when CS makes a high-to-low transition, and waveform 2 shows the SCK signal being high

when CS makes a high-to-low transition. In both cases, output SO becomes valid while the

SCK signal is still low (SCK low time is specified as t_WL). Timing waveforms 1 and 2 conform to

RapidS serial interface but for frequencies up to 66MHz. Waveforms 1 and 2 are compatible with

SPI Mode 0 and SPI Mode 3, respectively.

Waveform 3 and waveform 4 illustrate general timing diagram for RapidS serial interface. These

are similar to waveform 1 and waveform 2, except that output SO is not restricted to become

valid during the t_WLperiod. These timing waveforms are valid over the full frequency range (max-

imum frequency = 66MHz) of the RapidS serial case.

35

3596O–DFLASH–1/2013

21.1 Waveform 1 – SPI Mode 0 Compatible (for Frequencies up to 66MHz)

t_CS

CS

t_CSS

t_WH

t_WL

t_CSH

SCK

SO

SI

t_V

t_HO

t_DIS

HIGH IMPEDANCE

t_SU

HIGH IMPEDANCE

VALID OUT

t_H

VALID IN

21.2 Waveform 2 – SPI Mode 3 Compatible (for Frequencies up to 66MHz)

t_CS

CS

t_CSS

t_WL

t_WH

t_CSH

SCK

SO

t_V

t_HO

t_DIS

HIGH Z

HIGH IMPEDANCE

VALID OUT

t_H

t_SU

VALID IN

SI

21.3 Waveform 3 – RapidS Mode 0 (F_MAX= 66MHz)

t_CS

CS

t_CSS

t_WH

t_WL

t_CSH

SCK

SO

SI

t_V

t_HO

VALID OUT

t_DIS

HIGH IMPEDANCE

t_SU

HIGH IMPEDANCE

t_H

VALID IN

21.4 Waveform 4 – RapidS Mode 3 (F_MAX= 66MHz)

t_CS

CS

t_CSS

t_WL

t_WH

t_CSH

SCK

SO

t_V

t_HO

t_DIS

HIGH Z

HIGH IMPEDANCE

VALID OUT

t_H

t_SU

VALID IN

SI

36

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

21.5 Utilizing the RapidS Function

To take advantage of the RapidS function's ability to operate at higher clock frequencies, a full

clock cycle must be used to transmit data back and forth across the serial bus. The DataFlash is

designed to always clock its data out on the falling edge of the SCK signal and clock data in on

the rising edge of SCK.

For full clock cycle operation to be achieved, when the DataFlash is clocking data out on the fall-

ing edge of SCK, the host controller should wait until the next falling edge of SCK to latch the

data in. Similarly, the host controller should clock its data out on the rising edge of SCK in order

to give the DataFlash a full clock cycle to latch the incoming data in on the next rising edge of

SCK.

Figure 21-1. RapidS Mode

Slave CS

1

8

1

8

1

2

3

4

5

6

7

2

3

4

5

6

7

SCK

B

E

A

C

D

MSB

LSB

MOSI

MISO

BYTE-MOSI

H

G

I

F

MSB

LSB

BYTE-SO

MOSI = Master Out, Slave In

MISO = Master In, Slave Out

The Master is the host controller and the Slave is the DataFlash

The Master always clocks data out on the rising edge of SCK and always clocks data in on the falling edge of SCK.

The Slave always clocks data out on the falling edge of SCK and always clocks data in on the rising edge of SCK.

A. Master clocks out first bit of BYTE-MOSI on the rising edge of SCK

B. Slave clocks in first bit of BYTE-MOSI on the next rising edge of SCK

C. Master clocks out second bit of BYTE-MOSI on the same rising edge of SCK

D. Last bit of BYTE-MOSI is clocked out from the Master

E. Last bit of BYTE-MOSI is clocked into the slave

F. Slave clocks out first bit of BYTE-SO

G. Master clocks in first bit of BYTE-SO

H. Slave clocks out second bit of BYTE-SO

I. Master clocks in last bit of BYTE-SO

37

3596O–DFLASH–1/2013

21.6 Reset Timing

CS

t

CSS

REC

SCK

RESET

t

RST

HIGH IMPEDANCE

SO (OUTPUT)

SI (INPUT)

Note:

The CS signal should be in the high state before the RESET signal is deasserted

21.7 Command Sequence for Read/Write Operations for Page Size 256-Bytes

(Except Status Register Read, Manufacturer and Device ID Read)

SI (INPUT)

CMD

8 bits

X X X X X X X X X X X X X X X

X X X X X X X X

LSB

MSB

4 Don’t Care

Bits

Page Address

(A19 - A8)

Byte/Buffer Address

(A7 - A0/BFA7 - BFA0)

21.8 Command Sequence for Read/Write Operations for Page Size 264-Bytes

(Except Status Register Read, Manufacturer and Device ID Read)

SI (INPUT)

CMD

8 bits

X X X X X X X X X X X X X X X

X

X X X X X X X X

LSB

MSB

3 Don’t Care

Bits

Page Address

(PA11 - PA0)

Byte/Buffer Address

(BA8 - BA0/BFA8 - BFA0)

38

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

22. Write Operations

The following block diagram and waveforms illustrate the various write sequences available.

FLASH MEMORY ARRAY

PAGE (256-/264-BYTES)

BUFFER 1 TO

MAIN MEMORY

PAGE PROGRAM

BUFFER 2 TO

MAIN MEMORY

PAGE PROGRAM

BUFFER 1 (256-/264-BYTES)

BUFFER 2 (256-/264-BYTES)

BUFFER 1

WRITE

BUFFER 2

WRITE

I/O INTERFACE

SI

22.1 Buffer Write

Completes writing into selected buffer

CS

BINARY PAGE SIZE

16 DON'T CARE + BFA7-BFA0

SI (INPUT)

n

n+1

CMD

X

BFA7-0

X···X, BFA8

Last Byte

22.2 Buffer to Main Memory Page Program (Data from Buffer Programmed into Flash Page)

Starts self-timed erase/program operation

CS

BINARY PAGE SIZE

A19-A8 + 8 DON'T CARE BITS

SI (INPUT)

XXXX XX

CMD

PA10-7

PA6, X

Each transition

represents 8 bits

n = 1st byte read

n+1 = 2nd byte read

39

3596O–DFLASH–1/2013

23. Read Operations

The following block diagram and waveforms illustrate the various read sequences available.

FLASH MEMORY ARRAY

PAGE (256-/264-BYTES)

MAIN MEMORY

PAGE TO

MAIN MEMORY

PAGE TO

BUFFER 1

BUFFER 2

BUFFER 1 (256-/264-BYTES)

BUFFER 2 (256-/264-BYTES)

BUFFER 1

READ

MAIN MEMORY

PAGE READ

BUFFER 2

READ

I/O INTERFACE

SO

23.1 Main Memory Page Read

CS

ADDRESS FOR BINARY PAGE SIZE

A15-A8

A19-A16

A7-A0

SI (INPUT)

PA11-7

BA7-0

X

PA6-0, BA8

CMD

4 Dummy Bytes for Serial

SO (OUTPUT)

n

n+1

23.2 Main Memory Page to Buffer Transfer (Data from Flash Page Read into Buffer)

Starts reading page data into buffer

CS

BINARY PAGE SIZE

A19-A8 + 8 DON'T CARE BITS

CMD

PA11-7

SI (INPUT)

PA6-0, X

XXXX XXXX

SO (OUTPUT)

40

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

23.3 Buffer Read

CS

BINARY PAGE SIZE

15 DON'T CARE + BFA8-BFA0

1 Dummy Byte

X

CMD

X

X..X, BFA9-8

BFA7- 0

SI (INPUT)

n

n+1

SO (OUTPUT)

Each transition

represents 8 bits

24. Detailed Bit-level Read Waveform –

RapidS Serial Interface Mode 0/Mode 3

24.1 Continuous Array Read (Legacy Opcode E8H)

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34

62 63 64 65 66 67 68 69 70 71 72

SCK

SI

OPCODE

ADDRESS BITS

32 DON'T CARE BITS

1

0

1

0

A

X

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

SO

MSB

BIT 0 OF

PAGE n+1

BIT 2047/2111

OF PAGE n

24.2 Continuous Array Read (Opcode 0BH)

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

SCK

SI

OPCODE

ADDRESS BITS A19 - A0

DON'T CARE

X

0

1

0

1

A

X

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

SO

MSB

41

3596O–DFLASH–1/2013

24.3 Continuous Array Read (Low Frequency: Opcode 03H)

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39 40

SCK

SI

OPCODE

ADDRESS BITS A19-A0

0

1

A

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

SO

MSB

24.4 Main Memory Page Read (Opcode: D2H)

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34

62 63 64 65 66 67 68 69 70 71 72

SCK

SI

OPCODE

ADDRESS BITS

32 DON'T CARE BITS

1

0

1

0

1

0

A

X

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

SO

MSB

24.5 Buffer Read (Opcode D4H or D6H)

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

SCK

ADDRESS BITS

BINARY PAGE SIZE = 16 DON'T CARE + BFA7-BFA0

STANDARD DATAFLASH PAGE SIZE =

15 DON'T CARE + BFA8-BFA0

DON'T CARE

OPCODE

1

0

1

0

1

0

X

A

X

SI

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

SO

MSB

42

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

24.6 Buffer Read (Low Frequency: Opcode D1H or D3H)

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39 40

SCK

ADDRESS BITS

BINARY PAGE SIZE = 16 DON'T CARE + BFA7-BFA0

STANDARD DATAFLASH PAGE SIZE =

15 DON'T CARE + BFA8-BFA0

OPCODE

1

0

1

0

1

X

A

SI

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

SO

MSB

24.7 Read Sector Protection Register (Opcode 32H)

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39 40

SCK

SI

OPCODE

DON'T CARE

0

1

0

1

0

X

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

SO

MSB

24.8 Read Sector Lockdown Register (Opcode 35H)

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39 40

SCK

SI

OPCODE

DON'T CARE

0

1

0

1

0

1

X

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

SO

MSB

43

3596O–DFLASH–1/2013

24.9 Read Security Register (Opcode 77H)

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39 40

SCK

SI

OPCODE

DON'T CARE

0

1

0

1

X

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

SO

MSB

24.10 Status Register Read (Opcode D7H)

CS

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

SCK

SI

OPCODE

1

0

1

0

1

MSB

STATUS REGISTER DATA

HIGH-IMPEDANCE

D

SO

MSB

24.11 Manufacturer and Device Read (Opcode 9FH)

CS

0

6

7

8

14 15 16

22 23 24

30 31 32

38

SCK

SI

OPCODE

9FH

HIGH-IMPEDANCE

1FH

DEVICE ID BYTE 1 DEVICE ID BYTE 2

00H

SO

Note: Each transition

shown for SI and SO represents one byte (8 bits)

44

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

25. Auto Page Rewrite Flowchart

Figure 25-1. Algorithm for Programming or Reprogramming of the Entire Array Sequentially

START

provide address

and data

BUFFER WRITE

(84H, 87H)

MAIN MEMORY PAGE PROGRAM

THROUGH BUFFER

(82H, 85H)

BUFFER TO MAIN

MEMORY PAGE PROGRAM

(83H, 86H)

END

Notes: 1. This type of algorithm is used for applications in which the entire array is programmed sequentially, filling the array page-by-

page.

2. A page can be written using either a Main Memory Page Program operation or a Buffer Write operation followed by a Buffer

to Main Memory Page Program operation.

3. The algorithm above shows the programming of a single page. The algorithm will be repeated sequentially for each page

within the entire array.

45

3596O–DFLASH–1/2013

Figure 25-2. Algorithm for Randomly Modifying Data

START

provide address of

page to modify

MAIN MEMORY PAGE

If planning to modify multiple

bytes currently stored within

a page of the Flash array

TO BUFFER TRANSFER

(53H, 55H)

BUFFER WRITE

(84H, 87H)

MAIN MEMORY PAGE PROGRAM

THROUGH BUFFER

(82H, 85H)

BUFFER TO MAIN

MEMORY PAGE PROGRAM

(83H, 86H)

(2)

AUTO PAGE REWRITE

(58H, 59H)

INCREMENT PAGE

(2)

ADDRESS POINTER

END

Notes: 1. To preserve data integrity, each page of an DataFlash sector must be updated/rewritten at least once within every 10,000

cumulative page erase and program operations.

2. A Page Address Pointer must be maintained to indicate which page is to be rewritten. The Auto Page Rewrite command

must use the address specified by the Page Address Pointer.

3. Other algorithms can be used to rewrite portions of the Flash array. Low-power applications may choose to wait until 10,000

cumulative page erase and program operations have accumulated before rewriting all pages of the sector. See application

note AN-4 (“Using Serial DataFlash”) for more details.

46

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

26. Ordering Information

26.1 Ordering Code Detail

A T 4 5 D B 0 8 1 D – S S U

Designator

Product Family

Device Grade

U = Matte Sn lead finish, industrial

temperature range (-40°C to +85°C)

Device Density

Package Option

M

= 8-pad, 6 x 5 x 1mm MLF (VDFN)

8 = 8-megabit

SS = 8-lead, 0.150" wide SOIC

= 8-lead, 0.209" wide SOIC

S

Interface

1 = Serial

Device Revision

26.2 Green Package Options (Pb/Halide-free/RoHS Compliant)

Ordering Code⁽¹⁾⁽²⁾

Package

Lead Finish

Operating Voltage

f_SCK(MHz)

Operation Range

AT45DB081D-MU

AT45DB081D-MU-SL954⁽³⁾

AT45DB081D-MU-SL955⁽⁴⁾

8M1-A

AT45DB081D-SSU

AT45DB081D-SSU-SL954⁽³⁾

AT45DB081D-SSU-SL955⁽⁴⁾

8S1

8S2

Matte Sn

2.7V to 3.6V

66

Industrial

AT45DB081D-SU

(-40C to 85C)

AT45DB081D-SU-SL954⁽³⁾

AT45DB081D-SU-SL955⁽⁴⁾

AT45DB081D-MU-2.5

AT45DB081D-SSU-2.5

AT45DB081D-SU-2.5

8M1-A

8S1

Matte Sn

2.5V to 3.6V

50

8S2

Notes: 1. The shipping carrier option is not marked on the devices.

2. Standard parts are shipped with the page size set to 264-bytes. The user is able to configure these parts to a 256-byte page

size if desired.

3. Parts ordered with suffix SL954 are shipped in bulk with the page size set to 256-bytes. Parts will have a 954 or SL954

marked on them.

4. Parts ordered with suffix SL955 are shipped in tape and reel with the page size set to 256-bytes. Parts will have a 954 or

SL954 marked on them.

Package Type

8M1-A

8S1

8-pad, 6 x 5 x 1.00mm Body, Very Thin Dual Flat Package No Lead MLF^™(VDFN)

8-lead, 0.150” Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC)

8-lead, 0.209” Wide, Plastic Gull Wing Small Outline Package (EIAJ SOIC)

8S2

47

3596O–DFLASH–1/2013

27. Packaging Information

27.1 8M1-A – MLF (VDFN)

D

D1

0

Pin 1 ID

E

E1

SIDE VIEW

TOP VIEW

A3

A1

A2

A

0.08

C

COMMON DIMENSIONS

D2

(Unit of Measure = mm)

0.45

MIN

–

MAX

1.00

0.05

NOM

0.85

–

NOTE

SYMBOL

Pin #1 Notch

(0.20 R)

e

A

A1

A2

A3

b

–

E2

0.65 TYP

0.20 TYP

0.40

6.00

5.75

3.40

5.00

4.75

4.00

1.27

0.60

–

b

0.35

5.90

5.70

3.20

4.90

4.70

3.80

0.48

6.10

5.80

3.60

5.10

4.80

4.20

D

D1

D2

E

L

K

BOTTOM VIEW

E1

E2

e

L

0

0.50

–

0.75

12^o

–

K

0.25

–

8/28/08

GPC

YBR

DRAWING NO.

TITLE

REV.

8M1-A, 8-pad, 6 x 5 x 1.00mm Body, Thermally

Enhanced Plastic Very Thin Dual Flat No

Lead Package (VDFN)

Package Drawing Contact:

contact@adestotech.com

8M1-A

D

48

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

27.2 8S1 – JEDEC SOIC

C

1

E

E1

L

N

Ø

TOP VIIEWW

END VIEW

e

b

A

COMMON DIMENSIONS

(Unit of Measure = mm)

MIN

1.35

0.10

MAX

1.75

0.25

NOM

NOTE

SYMBOL

A1

A

–

A1

b

0.31

0.17

4.80

3.81

5.79

–

0.51

0.25

5.05

3.99

6.20

C

D

E1

E

e

–

D

–

SIDE VIEW

1.27 BSC

Notes: This drawing is for general information only.

Refer to JEDEC Drawing MS-012, Variation AA

for proper dimensions, tolerances, datums, etc.

L

0.40

0°

–

1.27

8°

Ø

5/19/10

TITLE

GPC

DRAWING NO.

REV.

Package Drawing Contact:

contact@adestotech.com

8S1, 8-lead (0.150”Wide Body), Plastic Gull

Wing Small Outline (JEDEC SOIC)

SWB

8S1

F

49

3596O–DFLASH–1/2013

27.3 8S2 – EIAJ SOIC

C

1

E

E1

L

End View

N

Top View

q

e

b

A

A1

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL

MIN

1.70

0.05

0.35

0.15

5.13

5.18

7.70

0.51

0˚

NOM

MAX

2.16

0.25

0.48

0.35

5.35

5.40

8.26

0.85

8˚

NOTE

A

D

A1

b

Side View

4

C

D

E1

E

Notes: 1. This drawing is for general information only; refer to

EIAJ Drawing EDR-7320 for additional information.

2. Mismatch of the upper and lower dies and resin burrs

are not included.

2

3. Determines the true geometric position.

4. Values b,C apply to plated terminal. The standard

thickness of the plating layer shall measure between

0.007 to .021mm.

L

q

3

e

1.27 BSC

4/15/08

TITLE

GPC

DRAWING NO.

REV.

8S2, 8-lead, 0.208” Body, Plastic Small

Outline Package (EIAJ)

Package Drawing Contact:

contact@adestotech.com

STN

8S2

F

50

AT45DB081D

3596O–DFLASH–1/2013

AT45DB081D

28. Revision History

Revision Level – Release Date History

A – November 2005

B – March 2006

Initial Release

Added Preliminary.

Added text, in “Programming the Configuration Register”, to indicate

that power cycling is required to switch to “power of 2” page size

after the opcode enable has been executed.

Added “Legacy Commands” table.

Corrected PA3 in opcode 50h for addressing sequence with

standard page size. Corrected Chip Erase opcode from 7CH to

C7H. Clarified the commands B and C usage for operation mode.

C – July 2006

Removed Preliminary.

D – November 2006

E – February 2007

Added errata regarding Chip Erase.

Changed various timing parameters under Table 18-4.

Removed RDY/BUSY pin references.

Removed SER/BYTE statement from SI and SO pin descriptions in

Table 2-1.

Added additional text to “power of 2” binary page size option.

F – August 2007

G – January 2008

Changed t_VSCLfrom 50μs to 70μs.

Changed t_RDPDfrom 30μs to 35μs.

Added additional text, in “power of 2” binary page size option, to

indicate that the address format is changed for devices with page

size set to 256-bytes.

Corrected typographical error to indicate that Figure 13-1 indicates

Program Configuration Register.

H – January 2008

I – April 2008

Removed DataFlash card pinout.

Added part number ordering code details for suffixes SL954/955

Added ordering code details.

J – February 2009

Changed t_DIS(Typ and Max) to 27ns and 35ns, respectively.

Changed Deep Power-Down Current values

- Increased typical value from 5μA to 15μA.

- Increased maximum value from 15μA to25 μA.

K – March 2009

L – April 2009

Updated Absolute Maximum Ratings

Removed Chip Erase Errata

Changed t_SE(Typ) 1.6 to 0.7 and (Max) 5 to 1.3

Changed t_CE(Typ) TBD to 7 and (Max) TBD to 22

M – May 2010

Changed from 10,000 to 20,000 cumulative page erase/program

operations and added the contact statement in section 11.3.

N – November 2012

O - January 2013

Update to Adesto.

change to 2 buffers in diagram 22-1

51

3596O–DFLASH–1/2013

29. Errata

29.1 No Errata Conditions

52

AT45DB081D

3596O–DFLASH–1/2013

Corporate Office

California | USA

Adesto Headquarters

1250 Borregas Avenue

Sunnyvale, CA 94089

Phone: (+1) 408.400.0578

Email: contact@adestotech.com

Adesto^®, the Adesto logo, CBRAM^®, and DataFlash^®are registered trademarks or trademarks of Adesto Technologies. All other marks are the property of their respective

owners.

Disclaimer: The information in this document is provided in connection with Adesto products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this

document or in connection with the sale of Adesto products. EXCEPT AS SET FORTH IN THE ADESTO TERMS AND CONDITIONS OF SALES LOCATED ON THE ADESTO WEBSITE, ADESTO

ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ADESTO BE LIABLE FOR ANY DIRECT, INDIRECT,

CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF

INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ADESTO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Adesto makes no

representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time

without notice. Adesto does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Adesto products are not suitable for, and shall not be used in,

automotive applications. Adesto products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.


型号：	AT45DB081D-SSU-2.5
厂家：	ADI
描述：	8-megabit 2.5V or 2.7V DataFlash 8兆位2.5V或2.7V的DataFlash 内存集成电路光电二极管时钟
文件：	总53页 (文件大小：1867K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

AT45DB081D-SSU-2.5 [ADI]

相关型号：

AT45DB081D-SSU-SL954

AT45DB081D-SSU-SL954

AT45DB081D-SSU-SL955

AT45DB081D-SSU-SL955

AT45DB081D-SU

AT45DB081D-SU

AT45DB081D-SU-2.5

AT45DB081D-SU-2.5

AT45DB081D-SU-SL954

AT45DB081D-SU-SL954

AT45DB081D-SU-SL955

AT45DB081D-SU-SL955