ADSP-2189MKST-300 [ADI]
DSP Microcomputer; 微电脑DSP型号: | ADSP-2189MKST-300 |
厂家: | ADI |
描述: | DSP Microcomputer |
文件: | 总32页 (文件大小:243K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
a
DSP Microcomputer
ADSP-2189M
FUNCTIONAL BLOCK DIAGRAM
FEATURES
PERFORMANCE
POWER-DOWN
CONTROL
13.3 ns Instruction Cycle Time @ 2.5 Volts (Internal),
75 MIPS Sustained Performance
Single-Cycle Instruction Execution
Single-Cycle Context Switch
FULL MEMORY
MODE
MEMORY
PROGRAMMABLE
DATA ADDRESS
GENERATORS
DATA
MEMORY
48K
؋
PROGRAM
MEMORY
32K
؋
I/O
PROGRAM
SEQUENCER
EXTERNAL
ADDRESS
BUS
AND
FLAGS
DAG 2
DAG 1
16 BIT
24 BIT
EXTERNAL
DATA
3-Bus Architecture Allows Dual Operand Fetches in
Every Instruction Cycle
Multifunction Instructions
Power-Down Mode Featuring Low CMOS Standby
Power Dissipation with 200 CLKIN Cycle Recovery
from Power-Down Condition
PROGRAM MEMORY ADDRESS
DATA MEMORY ADDRESS
BUS
BYTE DMA
CONTROLLER
PROGRAM MEMORY DATA
DATA MEMORY DATA
OR
EXTERNAL
DATA
BUS
Low Power Dissipation in Idle Mode
ARITHMETIC UNITS
SERIAL PORTS
SPORT 0 SPORT 1
TIMER
INTERNAL
DMA
ALU
SHIFTER
MAC
PORT
INTEGRATION
ADSP-2100 BASE
ARCHITECTURE
HOST MODE
ADSP-2100 Family Code Compatible (Easy to Use Alge-
braic Syntax), with Instruction Set Extensions
192K Bytes of On-Chip RAM, Configured as 32K Words
On-Chip Program Memory RAM and 48K Words On-
Chip Data Memory RAM
Dual Purpose Program Memory for Both Instruction
and Data Storage
Independent ALU, Multiplier/Accumulator and Barrel
Shifter Computational Units
Six External Interrupts
13 Programmable Flag Pins Provide Flexible System
Signaling
UART Emulation through Software SPORT Reconfiguration
ICE-Port™ Emulator Interface Supports Debugging in
Final Systems
Two Independent Data Address Generators
Powerful Program Sequencer Provides Zero Overhead
Looping Conditional Instruction Execution
Programmable 16-Bit Interval Timer with Prescaler
100-Lead LQFP
GENERAL DESCRIPTION
The ADSP-2189M is a single-chip microcomputer optimized
for digital signal processing (DSP) and other high speed nu-
meric processing applications.
SYSTEM INTERFACE
Flexible I/O Structure Allows 2.5 V or 3.3 V Operation;
All Inputs Tolerate Up to 3.6 V, Regardless of Mode
16-Bit Internal DMA Port for High Speed Access to On-
Chip Memory (Mode Selectable)
4 MByte Memory Interface for Storage of Data Tables
and Program Overlays (Mode Selectable)
8-Bit DMA to Byte Memory for Transparent Program
and Data Memory Transfers (Mode Selectable)
I/O Memory Interface with 2048 Locations Supports
Parallel Peripherals (Mode Selectable)
The ADSP-2189M combines the ADSP-2100 family base archi-
tecture (three computational units, data address generators and
a program sequencer) with two serial ports, a 16-bit internal
DMA port, a byte DMA port, a programmable timer, Flag I/O,
extensive interrupt capabilities, and on-chip program and data
memory.
The ADSP-2189M integrates 192K bytes of on-chip memory
configured as 32K words (24-bit) of program RAM and 48K
words (16-bit) of data RAM. Power-down circuitry is also pro-
vided to meet the low power needs of battery operated portable
equipment. The ADSP-2189M is available in a 100-lead LQFP
package.
Programmable Memory Strobe and Separate I/O
Memory Space Permits “Glueless” System Design
Programmable Wait-State Generation
In addition, the ADSP-2189M supports new instructions, which
include bit manipulations—bit set, bit clear, bit toggle, bit test—
new ALU constants, new multiplication instruction (x squared),
biased rounding, result free ALU operations, I/O memory trans-
fers and global interrupt masking, for increased flexibility.
Two Double-Buffered Serial Ports with Companding
Hardware and Automatic Data Buffering
Automatic Booting of On-Chip Program Memory from
Byte-Wide External Memory, e.g., EPROM, or
Through Internal DMA Port
ICE-Port is a trademark of Analog Devices, Inc.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
World Wide Web Site: http://www.analog.com
© Analog Devices, Inc., 2000
ADSP-2189M
The EZ-ICE performs a full range of functions, including:
Fabricated in a high speed, low power, CMOS process, the
ADSP-2189M operates with a 13.3 ns instruction cycle time.
Every instruction can execute in a single processor cycle.
• In-target operation
• Up to 20 breakpoints
• Single-step or full-speed operation
The ADSP-2189M’s flexible architecture and comprehensive
instruction set allow the processor to perform multiple opera-
tions in parallel. In one processor cycle, the ADSP-2189M can:
• Registers and memory values can be examined and altered
• PC upload and download functions
• Instruction-level emulation of program booting and execution
• Complete assembly and disassembly of instructions
• C source-level debugging
• Generate the next program address
• Fetch the next instruction
• Perform one or two data moves
• Update one or two data address pointers
• Perform a computational operation
See “Designing An EZ-ICE-Compatible Target System” in the
ADSP-2100 Family EZ-Tools Manual (ADSP-2181 sections) as
well as the Designing an EZ-ICE compatible System section of
this data sheet for the exact specifications of the EZ-ICE target
board connector.
This takes place while the processor continues to:
• Receive and transmit data through the two serial ports
• Receive and/or transmit data through the internal DMA port
• Receive and/or transmit data through the byte DMA port
• Decrement timer
Additional Information
This data sheet provides a general overview of ADSP-2189M
functionality. For additional information on the architecture and
instruction set of the processor, refer to the ADSP-2100 Family
User’s Manual, Third Edition. For more information about the
development tools, refer to the ADSP-2100 Family Develop-
ment Tools Data Sheet.
DEVELOPMENT SYSTEM
The ADSP-2100 Family Development Software, a complete set
of tools for software and hardware system development, sup-
ports the ADSP-2189M. The System Builder provides a high
level method for defining the architecture of systems under
development. The Assembler has an algebraic syntax that is easy
to program and debug. The Linker combines object files into an
executable file. The Simulator provides an interactive instruc-
tion-level simulation with a reconfigurable user interface to
display different portions of the hardware environment.
ARCHITECTURE OVERVIEW
The ADSP-2189M instruction set provides flexible data moves
and multifunction (one or two data moves with a computation)
instructions. Every instruction can be executed in a single pro-
cessor cycle. The ADSP-2189M assembly language uses an
algebraic syntax for ease of coding and readability. A compre-
hensive set of development tools supports program development.
A PROM Splitter generates PROM programmer compatible
files. The C Compiler, based on the Free Software Foundation’s
GNU C Compiler, generates ADSP-2189M assembly source
code. The source code debugger allows programs to be cor-
rected in the C environment. The Runtime Library includes over
100 ANSI-standard mathematical and DSP-specific functions.
POWER-DOWN
CONTROL
FULL MEMORY
MODE
MEMORY
PROGRAMMABLE
DATA ADDRESS
GENERATORS
DATA
PROGRAM
MEMORY
32K
؋
I/O
PROGRAM
SEQUENCER
EXTERNAL
ADDRESS
BUS
MEMORY
48K
؋
AND
FLAGS
DAG 2
DAG 1
16 BIT
24 BIT
EXTERNAL
DATA
The EZ-KIT Lite is a hardware/software kit offering a complete
development environment for the entire ADSP-21xx family: an
ADSP-218x-based evaluation board with PC monitor software
plus Assembler, Linker, Simulator and PROM Splitter software.
The ADSP-218x EZ-KIT Lite is a low cost, easy to use hard-
ware platform on which you can quickly get started with your
DSP software design. The EZ-KIT Lite includes the following
features:
PROGRAM MEMORY ADDRESS
DATA MEMORY ADDRESS
BUS
BYTE DMA
CONTROLLER
PROGRAM MEMORY DATA
DATA MEMORY DATA
OR
EXTERNAL
DATA
BUS
ARITHMETIC UNITS
SERIAL PORTS
SPORT 0 SPORT 1
TIMER
INTERNAL
DMA
PORT
ALU
SHIFTER
MAC
ADSP-2100 BASE
ARCHITECTURE
HOST MODE
• 33 MHz ADSP-218x
• Full 16-bit Stereo Audio I/O with AD1847 SoundPort®
Codec
Figure 1. Functional Block Diagram
• RS-232 Interface to PC with Windows 3.1 Control Software
• EZ-ICE Connector for Emulator Control
• DSP Demo Programs
Figure 1 is an overall block diagram of the ADSP-2189M. The
processor contains three independent computational units: the
ALU, the multiplier/accumulator (MAC) and the shifter. The
computational units process 16-bit data directly and have provi-
sions to support multiprecision computations. The ALU per-
forms a standard set of arithmetic and logic operations; division
primitives are also supported. The MAC performs single-cycle
multiply, multiply/add and multiply/subtract operations with 40
bits of accumulation. The shifter performs logical and arith-
metic shifts, normalization, denormalization and derive expo-
nent operations.
The ADSP-218x EZ-ICE® Emulator aids in the hardware de-
bugging of an ADSP-2189M system. The emulator consists of
hardware, host computer resident software and the target board
connector. The ADSP-2189M integrates on-chip emulation
support with a 14-pin ICE-Port interface. This interface pro-
vides a simpler target board connection that requires fewer
mechanical clearance considerations than other ADSP-2100
Family EZ-ICEs. The ADSP-2189M device need not be re-
moved from the target system when using the EZ-ICE, nor are
any adapters needed. Due to the small footprint of the EZ-ICE
connector, emulation can be supported in final board designs.
The shifter can be used to efficiently implement numeric
format control including multiword and block floating-point
representations.
EZ-ICE and SoundPort are registered trademarks of Analog Devices, Inc.
–2–
REV. A
ADSP-2189M
The internal result (R) bus connects the computational units so
that the output of any unit may be the input of any unit on the
next cycle.
RESET signal. The two serial ports provide a complete synchro-
nous serial interface with optional companding in hardware and
a wide variety of framed or frameless data transmit and receive
modes of operation.
A powerful program sequencer and two dedicated data address
generators ensure efficient delivery of operands to these compu-
tational units. The sequencer supports conditional jumps, sub-
routine calls and returns in a single cycle. With internal loop
counters and loop stacks, the ADSP-2189M executes looped
code with zero overhead; no explicit jump instructions are re-
quired to maintain loops.
Each port can generate an internal programmable serial clock or
accept an external serial clock.
The ADSP-2189M provides up to 13 general-purpose flag pins.
The data input and output pins on SPORT1 can be alternatively
configured as an input flag and an output flag. In addition, eight
flags are programmable as inputs or outputs and three flags are
always outputs.
Two data address generators (DAGs) provide addresses for
simultaneous dual operand fetches (from data memory and
program memory). Each DAG maintains and updates four
address pointers. Whenever the pointer is used to access data
(indirect addressing), it is post-modified by the value of one of
four possible modify registers. A length value may be associated
with each pointer to implement automatic modulo addressing
for circular buffers.
A programmable interval timer generates periodic interrupts. A
16-bit count register (TCOUNT) decrements every n processor
cycles, where n is a scaling value stored in an 8-bit register
(TSCALE). When the value of the count register reaches zero,
an interrupt is generated and the count register is reloaded from
a 16-bit period register (TPERIOD).
Serial Ports
Efficient data transfer is achieved with the use of five internal
buses:
The ADSP-2189M incorporates two complete synchronous
serial ports (SPORT0 and SPORT1) for serial communications
and multiprocessor communication.
• Program Memory Address (PMA) Bus
• Program Memory Data (PMD) Bus
• Data Memory Address (DMA) Bus
• Data Memory Data (DMD) Bus
• Result (R) Bus
Here is a brief list of the capabilities of the ADSP-2189M
SPORTs. For additional information on Serial Ports, refer to
the ADSP-2100 Family User’s Manual, Third Edition.
• SPORTs are bidirectional and have a separate, double-buff-
ered transmit and receive section.
The two address buses (PMA and DMA) share a single external
address bus, allowing memory to be expanded off-chip and the
two data buses (PMD and DMD) share a single external data
bus. Byte memory space and I/O memory space also share the
external buses.
• SPORTs can use an external serial clock or generate their
own serial clock internally.
• SPORTs have independent framing for the receive and trans-
mit sections. Sections run in a frameless mode or with frame
synchronization signals internally or externally generated.
Frame sync signals are active high or inverted, with either of
two pulsewidths and timings.
Program memory can store both instructions and data, permit-
ting the ADSP-2189M to fetch two operands in a single cycle,
one from program memory and one from data memory. The
ADSP-2189M can fetch an operand from program memory and
the next instruction in the same cycle.
• SPORTs support serial data word lengths from 3 to 16 bits
and provide optional A-law and µ-law companding according
to CCITT recommendation G.711.
In lieu of the address and data bus for external memory connec-
tion, the ADSP-2189M may be configured for 16-bit Internal
DMA port (IDMA port) connection to external systems. The
IDMA port is made up of 16 data/address pins and five control
pins. The IDMA port provides transparent, direct access to the
DSPs on-chip program and data RAM.
• SPORT receive and transmit sections can generate unique
interrupts on completing a data word transfer.
• SPORTs can receive and transmit an entire circular buffer of
data with only one overhead cycle per data word. An interrupt
is generated after a data buffer transfer.
An interface to low cost byte-wide memory is provided by the
Byte DMA port (BDMA port). The BDMA port is bidirectional
and can directly address up to four megabytes of external RAM
or ROM for off-chip storage of program overlays or data tables.
• SPORT0 has a multichannel interface to selectively receive
and transmit a 24- or 32-word, time-division multiplexed,
serial bitstream.
The byte memory and I/O memory space interface supports
slow memories and I/O memory-mapped peripherals with pro-
grammable wait-state generation. External devices can gain
control of external buses with bus request/grant signals (BR,
BGH and BG). One execution mode (Go Mode) allows the
ADSP-2189M to continue running from on-chip memory.
Normal execution mode requires the processor to halt while
buses are granted.
• SPORT1 can be configured to have two external interrupts
(IRQ0 and IRQ1) and the Flag In and Flag Out signals. The
internally generated serial clock may still be used in this con-
figuration.
PIN DESCRIPTIONS
The ADSP-2189M will be available in a 100-lead LQFP pack-
age. In order to maintain maximum functionality and reduce
package size and pin count, some serial port, programmable
flag, interrupt and external bus pins have dual, multiplexed
functionality. The external bus pins are configured during
RESET only, while serial port pins are software configurable
during program execution. Flag and interrupt functionality is
retained concurrently on multiplexed pins. In cases where pin
The ADSP-2189M can respond to eleven interrupts. There can
be up to six external interrupts (one edge-sensitive, two level-
sensitive and three configurable) and seven internal interrupts
generated by the timer, the serial ports (SPORTs), the Byte
DMA port and the power-down circuitry. There is also a master
REV. A
–3–
ADSP-2189M
NOTES
functionality is reconfigurable, the default state is shown in plain
text; alternate functionality is shown in italics.
1Interrupt/Flag Pins retain both functions concurrently. If IMASK is set to
enable the corresponding interrupts, then the DSP will vector to the appropri-
ate interrupt vector address when the pin is asserted, either by external devices,
or set as a programmable flag.
Common-Mode Pins
Pin
# of
2SPORT configuration determined by the DSP System Control Register. Soft-
ware configurable.
Name(s)
Pins I/O Function
Memory Interface Pins
RESET
BR
1
1
1
1
1
1
1
1
1
1
1
1
I
I
Processor Reset Input
Bus Request Input
Bus Grant Output
The ADSP-2189M processor can be used in one of two modes,
Full Memory Mode, which allows BDMA operation with full
external overlay memory and I/O capability, or Host Mode,
which allows IDMA operation with limited external addressing
capabilities. The operating mode is determined by the state of
the Mode C pin during RESET and cannot be changed while
the processor is running.
BG
O
O
O
O
O
O
O
O
O
I
BGH
DMS
PMS
IOMS
BMS
CMS
RD
Bus Grant Hung Output
Data Memory Select Output
Program Memory Select Output
Memory Select Output
Byte Memory Select Output
Combined Memory Select Output
Memory Read Enable Output
Memory Write Enable Output
Full Memory Mode Pins (Mode C = 0)
Pin
Name
# of
Pins
I/O
Function
WR
A13:0
14
O
Address Output Pins for Program,
Data, Byte and I/O Spaces
Data I/O Pins for Program, Data,
Byte and I/O Spaces (8 MSBs are
also used as Byte Memory addresses.)
IRQ2
Edge- or Level-Sensitive Interrupt
Requests1
D23:0
24
I/O
PF7
IRQL1
PF6
IRQL0
PF5
IRQE
PF4
Mode D
I/O Programmable I/O Pin.
Level-Sensitive Interrupt Requests1
I/O Programmable I/O Pin
Level-Sensitive Interrupt Requests1
I/O Programmable I/O Pin
Edge-Sensitive Interrupt Requests1
I/O Programmable I/O Pin
1
1
1
1
I
Host Mode Pins (Mode C = 1)
I
Pin
Name
# of
Pins
I/O
Function
I
IAD15:0 16
I/O
O
IDMA Port Address/Data Bus
Address Pin for External I/O,
Program, Data, or Byte Access1
Data I/O Pins for Program, Data
Byte and I/O Spaces
I
Mode Select Input—Checked Only
During RESET
A0
1
PF3
I/O Programmable I/O Pin During
Normal Operation
D23:8
16
I/O
IWR
IRD
IAL
IS
1
1
1
1
1
I
I
I
I
IDMA Write Enable
IDMA Read Enable
IDMA Address Latch Pin
IDMA Select
IDMA Port Acknowledge Config-
Mode C
1
I
Mode Select Input—Checked Only
During RESET
PF2
I/O Programmable I/O Pin During
Normal Operation
I
IACK
O
Mode B
PF1
1
1
Mode Select Input—Checked
Only During RESET
urable in Mode D; Open Drain
I/O Programmable I/O Pin During
NOTE
1In Host Mode, external peripheral addresses can be decoded using the A0,
Normal Operation
Mode Select Input—Checked Only
During RESET
CMS, PMS, DMS and IOMS signals.
Mode A
PF0
I
Interrupts
The interrupt controller allows the processor to respond to the
eleven possible interrupts and reset with minimum overhead.
The ADSP-2189M provides four dedicated external interrupt
input pins, IRQ2, IRQL0, IRQL1 and IRQE (shared with the
PF7:4 pins). In addition, SPORT1 may be reconfigured for
IRQ0, IRQ1, FLAG_IN and FLAG_OUT, for a total of six
external interrupts. The ADSP-2189M also supports internal
interrupts from the timer, the byte DMA port, the two serial
ports, software and the power-down control circuit. The inter-
rupt levels are internally prioritized and individually maskable
(except power-down and reset). The IRQ2, IRQ0 and IRQ1
input pins can be programmed to be either level- or edge-sensi-
tive. IRQL0 and IRQL1 are level-sensitive and IRQE is edge-
sensitive. The priorities and vector addresses of all interrupts are
shown in Table I.
I/O Programmable I/O Pin During
Normal Operation
I
CLKIN, XTAL 2
CLKOUT
SPORT0
SPORT1
IRQ1:0, FI, FO
Clock or Quartz Crystal Input
Processor Clock Output
1
5
5
O
I/O Serial Port I/O Pins
I/O Serial Port I/O Pins
Edge- or Level-Sensitive Interrupts,
Flag In, Flag Out2
PWD
1
1
3
2
4
I
Power-Down Control Input
Power-Down Control Output
Output Flags
Internal VDD (2.5 V) Power
External VDD (2.5 V or 3.3 V)
Power
PWDACK
FL0, FL1, FL2
VDDINT
O
O
I
VDDEXT
I
GND
EZ-Port
10
9
I
Ground
I/O For Emulation Use
–4–
REV. A
ADSP-2189M
Table I. Interrupt Priority and Interrupt Vector Addresses
Interrupt Vector
Third Edition, “System Interface” chapter, for detailed infor-
mation about the power-down feature.
•
Quick recovery from power-down. The processor begins
executing instructions in as few as 200 CLKIN cycles.
Source Of Interrupt
Address (Hex)
RESET (or Power-Up with PUCR = 1) 0000 (Highest Priority)
•
Support for an externally generated TTL or CMOS proces-
sor clock. The external clock can continue running during
power-down without affecting the lowest power rating and
200 CLKIN cycle recovery.
Power-Down (Nonmaskable)
IRQ2
002C
0004
IRQL1
0008
IRQL0
000C
•
•
Support for crystal operation includes disabling the oscillator
to save power (the processor automatically waits approxi-
mately 4096 CLKIN cycles for the crystal oscillator to start
or stabilize) and letting the oscillator run to allow 200 CLKIN
cycle start up.
SPORT0 Transmit
SPORT0 Receive
IRQE
BDMA Interrupt
SPORT1 Transmit or IRQ1
SPORT1 Receive or IRQ0
Timer
0010
0014
0018
001C
0020
0024
Power-down is initiated by either the power-down pin
(PWD) or the software power-down force bit. Interrupt
support allows an unlimited number of instructions to be
executed before optionally powering down. The power-down
interrupt also can be used as a nonmaskable, edge-sensitive
interrupt.
0028 (Lowest Priority)
Interrupt routines can either be nested with higher priority
interrupts taking precedence or processed sequentially. Inter-
rupts can be masked or unmasked with the IMASK register.
Individual interrupt requests are logically ANDed with the bits
in IMASK; the highest priority unmasked interrupt is then
selected. The power-down interrupt is nonmaskable.
•
Context clear/save control allows the processor to continue
where it left off or start with a clean context when leaving the
power-down state.
The ADSP-2189M masks all interrupts for one instruction cycle
following the execution of an instruction that modifies the IMASK
register. This does not affect serial port autobuffering or DMA
transfers.
•
•
The RESET pin also can be used to terminate power-down.
Power-down acknowledge pin indicates when the processor
has entered power-down.
The interrupt control register, ICNTL, controls interrupt nest-
ing and defines the IRQ0, IRQ1 and IRQ2 external interrupts to
be either edge- or level-sensitive. The IRQE pin is an external
edge-sensitive interrupt and can be forced and cleared. The
IRQL0 and IRQL1 pins are external level-sensitive interrupts.
Idle
When the ADSP-2189M is in the Idle Mode, the processor
waits indefinitely in a low power state until an interrupt occurs.
When an unmasked interrupt occurs, it is serviced; execution
then continues with the instruction following the IDLE instruc-
tion. In Idle mode IDMA, BDMA and autobuffer cycle steals
still occur.
The IFC register is a write-only register used to force and clear
interrupts. On-chip stacks preserve the processor status and are
automatically maintained during interrupt handling. The stacks
are twelve levels deep to allow interrupt, loop and subroutine
nesting. The following instructions allow global enable or dis-
able servicing of the interrupts (including power-down), regard-
less of the state of IMASK. Disabling the interrupts does not
affect serial port autobuffering or DMA.
Slow Idle
The IDLE instruction is enhanced on the ADSP-2189M to let
the processor’s internal clock signal be slowed, further reducing
power consumption. The reduced clock frequency, a program-
mable fraction of the normal clock rate, is specified by a select-
able divisor given in the IDLE instruction.
The format of the instruction is:
ENA INTS;
DIS INTS;
IDLE (n);
When the processor is reset, interrupt servicing is enabled.
where n = 16, 32, 64 or 128. This instruction keeps the proces-
sor fully functional, but operating at the slower clock rate. While
it is in this state, the processor’s other internal clock signals,
such as SCLK, CLKOUT and timer clock, are reduced by the
same ratio. The default form of the instruction, when no clock
divisor is given, is the standard IDLE instruction.
LOW POWER OPERATION
The ADSP-2189M has three low power modes that significantly
reduce the power dissipation when the device operates under
standby conditions. These modes are:
• Power-Down
• Idle
• Slow Idle
When the IDLE (n) instruction is used, it effectively slows down
the processor’s internal clock and thus its response time to in-
coming interrupts. The one-cycle response time of the standard
idle state is increased by n, the clock divisor. When an enabled
interrupt is received, the ADSP-2189M will remain in the idle
state for up to a maximum of n processor cycles (n = 16, 32, 64,
or 128) before resuming normal operation.
The CLKOUT pin may also be disabled to reduce external
power dissipation.
Power-Down
The ADSP-2189M processor has a low power feature that lets
the processor enter a very low power dormant state through
hardware or software control. Here is a brief list of power-
down features. Refer to the ADSP-2100 Family User’s Manual,
When the IDLE (n) instruction is used in systems that have an
externally generated serial clock (SCLK), the serial clock rate
may be faster than the processor’s reduced internal clock rate.
Under these conditions, interrupts must not be generated at a
REV. A
–5–
ADSP-2189M
faster rate than can be serviced, due to the additional time the
processor takes to come out of the idle state (a maximum of n
processor cycles).
Clock Signals
The ADSP-2189M can be clocked by either a crystal or a TTL-
compatible clock signal.
The CLKIN input cannot be halted, changed during operation,
or operated below the specified frequency during normal opera-
tion. The only exception is while the processor is in the power-
down state. For additional information, refer to Chapter 9,
ADSP-2100 Family User’s Manual, Third Edition for detailed
information on this power-down feature.
SYSTEM INTERFACE
Figure 2 shows typical basic system configurations with the
ADSP-2189M, two serial devices, a byte-wide EPROM and
optional external program and data overlay memories (mode
selectable). Programmable Wait-State generation allows the
processor connects easily to slow peripheral devices. The
ADSP-2189M also provides four external interrupts and two
serial ports or six external interrupts and one serial port. Host
Memory Mode allows access to the full external data bus, but
limits addressing to a single address bit (A0). Additional system
peripherals can be added in this mode through the use of exter-
nal hardware to generate and latch address signals.
If an external clock is used, it should be a TTL-compatible
signal running at half the instruction rate. The signal is con-
nected to the processor’s CLKIN input. When an external clock
is used, the XTAL input must be left unconnected.
The ADSP-2189M uses an input clock with a frequency equal
to half the instruction rate; a 37.50 MHz input clock yields a
13.3 ns processor cycle (which is equivalent to 75 MHz). Nor-
mally, instructions are executed in a single processor cycle. All
device timing is relative to the internal instruction clock rate,
which is indicated by the CLKOUT signal when enabled.
FULL MEMORY MODE
ADSP-2189M
A
14
13-0
1/2x CLOCK
OR
CRYSTAL
ADDR13-0
CLKIN
A0-A21
D
23-16
XTAL
Because the ADSP-2189M includes an on-chip oscillator cir-
cuit, an external crystal may be used. The crystal should be
connected across the CLKIN and XTAL pins, with two capaci-
tors connected as shown in Figure 3. Capacitor values are de-
pendent on crystal type and should be specified by the crystal
manufacturer. A parallel-resonant, fundamental frequency,
microprocessor-grade crystal should be used.
BYTE
24
D
15-8
FL0-2
MEMORY
DATA
DATA23-0
IRQ2/PF7
IRQE/PF4
IRQL0/PF5
IRQL1/PF6
BMS
CS
A
10-0
WR
RD
ADDR
DATA
MODE D/PF3
MODE C/PF2
MODE B/PF1
MODE A/PF0
D
23-8
I/O SPACE
(PERIPHERALS)
2048 LOCATIONS
IOMS
CS
SPORT1
SCLK1
A
13-0
ADDR
DATA
A clock output (CLKOUT) signal is generated by the processor
at the processor’s cycle rate. This can be enabled and disabled
by the CLKODIS bit in the SPORT0 Autobuffer Control
Register.
OVERLAY
MEMORY
TWO 8K
RFS1 OR IRQ0
TFS1 OR IRQ1
DT1 OR FO
DR1 OR FI
D
23-0
SERIAL
DEVICE
PM SEGMENTS
PMS
DMS
CMS
TWO 8K
DM SEGMENTS
SPORT0
SCLK0
RFS0
TFS0
DT0
BR
BG
BGH
SERIAL
DEVICE
PWD
PWDACK
DR0
XTAL
CLKIN
CLKOUT
HOST MEMORY MODE
DSP
ADSP-2189M
CLKIN
1/2x CLOCK
OR
CRYSTAL
1
A0
XTAL
FL0-2
Figure 3. External Crystal Connections
16
IRQ2/PF7
DATA23-8
IRQE/PF4
IRQL0/PF5
IRQL1/PF6
Reset
BMS
The RESET signal initiates a master reset of the ADSP-2189M.
The RESET signal must be asserted during the power-up se-
quence to assure proper initialization. RESET during initial
power-up must be held long enough to allow the internal clock
to stabilize. If RESET is activated any time after power-up, the
clock continues to run and does not require stabilization time.
MODE D/PF3
MODE C/PF2
MODE B/PF1
MODE A/PF0
WR
RD
SPORT1
SCLK1
RFS1 OR IRQ0
TFS1 OR IRQ1
DT1 OR FO
DR1 OR FI
IOMS
SERIAL
DEVICE
The power-up sequence is defined as the total time required for
the crystal oscillator circuit to stabilize after a valid VDD is ap-
plied to the processor and for the internal phase-locked loop
(PLL) to lock onto the specific crystal frequency. A minimum of
2000 CLKIN cycles ensures that the PLL has locked but does
not include the crystal oscillator start-up time. During this
power-up sequence the RESET signal should be held low. On
any subsequent resets, the RESET signal must meet the mini-
SPORT0
SCLK0
RFS0
TFS0
DT0
PMS
DMS
CMS
SERIAL
DEVICE
BR
BG
BGH
DR0
IDMA PORT
IRD/D6
IWR/D7
IS/D4
IAL/D5
IACK/D3
PWD
PWDACK
SYSTEM
INTERFACE
OR
CONTROLLER
16
IAD15-0
mum pulsewidth specification, tRSP
.
The RESET input contains some hysteresis; however, if you use
an RC circuit to generate your RESET signal, the use of an
external Schmidt trigger is recommended.
Figure 2. ADSP-2189M Basic System Interface
–6–
REV. A
ADSP-2189M
Table II. ADSP-2189M Modes of Operation
MODE A Booting Method
MODE D MODE C
MODE B
X
0
0
0
BDMA feature is used to load the first 32 program memory words from the
byte memory space. Program execution is held off until all 32 words have
been loaded. Chip is configured in Full Memory Mode.1
X
0
1
0
0
No automatic boot operations occur. Program execution starts at external
memory location 0. Chip is configured in Full Memory Mode. BDMA can
still be used but the processor does not automatically use or wait for these
operations.
0
1
0
BDMA feature is used to load the first 32 program memory words from the
byte memory space. Program execution is held off until all 32 words have
been loaded. Chip is configured in Host Mode. IACK has active pull-down.
(REQUIRES ADDITIONAL HARDWARE).
0
1
1
1
0
0
1
0
IDMA feature is used to load any internal memory as desired. Program ex-
ecution is held off until internal program memory location 0 is written to.
Chip is configured in Host Mode. IACK has active pull-down.1
BDMA feature is used to load the first 32 program memory words from the
byte memory space. Program execution is held off until all 32 words have
been loaded. Chip is configured in Host Mode; IACK requires external pull-
down. (REQUIRES ADDITIONAL HARDWARE).
1
1
0
1
IDMA feature is used to load any internal memory as desired. Program ex-
ecution is held off until internal program memory location 0 is written to.
Chip is configured in Host Mode. IACK requires external pull-down.1
NOTE
1Considered as standard operating settings. Using these configurations allows for easier design and better memory management.
The master reset sets all internal stack pointers to the empty
stack condition, masks all interrupts and clears the MSTAT
register. When RESET is released, if there is no pending bus
request and the chip is configured for booting, the boot-loading
sequence is performed. The first instruction is fetched from
on-chip program memory location 0x0000 once boot loading
completes.
Passive Configuration involves the use a pull-up or pull-down
resistor connected to the Mode C pin. To minimize power
consumption, or if the PF2 pin is to be used as an output in the
DSP application, a weak pull-up or pull-down, on the order of
10 kΩ, can be used. This value should be sufficient to pull the
pin to the desired level and still allow the pin to operate as a
programmable flag output without undue strain on the processor’s
output driver. For minimum power consumption during power-
down, reconfigure PF2 to be an input, as the pull-up or pull-
down will hold the pin in a known state and will not switch.
Power Supplies
The ADSP-2189M has separate power supply connections for
the internal (VDDINT) and external (VDDEXT) power supplies.
The internal supply must meet the 2.5 V requirement. The
external supply can be connected to either a 2.5 V or 3.3 V
supply. All external supply pins must be connected to the same
supply. All input and I/O pins can tolerate input voltages up
to 3.6 V regardless of the external supply voltage. This fea-
ture provides maximum flexibility in mixing 2.5 V and 3.3 V
components.
Active Configuration involves the use of a three-statable ex-
ternal driver connected to the Mode C pin. A driver’s output
enable should be connected to the DSP’s RESET signal such
that it only drives the PF2 pin when RESET is active (low).
When RESET is deasserted, the driver should three-state, thus
allowing full use of the PF2 pin as either an input or output. To
minimize power consumption during power-down, configure
the programmable flag as an output when connected to a three-
stated buffer. This ensures that the pin will be held at a constant
level and will not oscillate should the three-state driver’s level
hover around the logic switching point.
MODES OF OPERATION
Setting Memory Mode
Memory Mode selection for the ADSP-2189M is made during
chip reset through the use of the Mode C pin. This pin is multi-
plexed with the DSP’s PF2 pin, so care must be taken in how
the mode selection is made. The two methods for selecting the
value of Mode C are active and passive.
IACK Configuration
Mode D = 0 and in host mode: IACK is an active, driven signal
and cannot be wire OR-ed.
REV. A
–7–
ADSP-2189M
1
PM (MODE B = 0)
PM (MODE B = 1)
ALWAYS
ACCESSIBLE
AT ADDRESS
0
؋
0000 – 0؋
1FFF RESERVED
0
؋
2000– 0
؋
3FFF ACCESSIBLE WHEN
PMOVLAY = 0
0
؋
2000– 0
؋
3FFF ACCESSIBLE WHEN
PMOVLAY = 0
0
؋
2000– 0
؋
3FFF INTERNAL
MEMORY
RESERVED
RESERVED
0
؋
2000– 0
؋
3FFF 0
؋
2000– 0
؋
0000– ACCESSIBLE WHEN
PMOVLAY = 4
INTERNAL
MEMORY
2
0
؋
1FFF 0
؋
0000– ACCESSIBLE WHEN
PMOVLAY = 5
ACCESSIBLE WHEN
PMOVLAY = 1
2
0
؋
3FFF 2
0
؋
1FFF 0
؋
2000– 0
؋
3FFF EXTERNAL
MEMORY
ACCESSIBLE WHEN
PMOVLAY = 1
RESERVED
2
EXTERNAL
MEMORY
ACCESSIBLE WHEN
PMOVLAY = 2
1
WHEN MODE B = 1, PMOVLAY MUST BE SET TO 0
2
SEE TABLE III FOR PMOVLAY BITS
PROGRAM MEMORY
MODE B = 0
PROGRAM MEMORY
MODE B = 1
ADDRESS
ADDRESS
0
؋
3FFF 0
؋
3FFF 8K INTERNAL
PMOVLAY = 0, 4, 5
OR
8K EXTERNAL
PMOVLAY = 1, 2
8K INTERNAL
PMOVLAY = 0
0
؋
2000 0
؋
1FFF 0
؋
2000 0
؋
1FFF 8K EXTERNAL
8K INTERNAL
0
؋
0000 0
؋
0000 Figure 4. Program Memory
Mode D = 1 and in host mode: IACK is an open source and
requires an external pull-down, but multiple IACK pins can be
wire OR-ed together.
Data Memory
Data Memory, Full Memory Mode is a 16-bit-wide space
used for the storage of data variables and for memory-mapped
control registers. The ADSP-2189M has 48K words on Data
Memory RAM on-chip. Part of this space is used by 32 memory-
mapped registers. Support also exists for up to two 8K external
memory overlay spaces through the external data bus. All inter-
nal accesses complete in one cycle. Accesses to external memory
are timed using the wait-states specified by the DWAIT register
and the wait-state mode bit.
MEMORY ARCHITECTURE
The ADSP-2189M provides a variety of memory and peripheral
interface options. The key functional groups are Program Memory,
Data Memory, Byte Memory and I/O. Refer to the following
figures and tables for PM and DM memory allocations in the
ADSP-2189M.
Program Memory
DATA MEMORY
ADDRESS
DATA MEMORY
Program Memory, Full Memory Mode is a 24-bit-wide space
for storing both instruction op codes and data. The ADSP-2189M
has 32K words of Program Memory RAM on chip and the
capability of accessing up to two 8K external memory overlay
spaces using the external data bus.
0
؋
3FFF 32 MEMORY–
MAPPED
REGISTERS
INTERNAL
8160
WORDS
ALWAYS
ACCESSIBLE
AT ADDRESS
0
؋
2000 – 0؋
3FFF 0
؋
3FE0 0
؋
3FDF 0
؋
2000 0
؋
1FFF 0
؋
0000– 0
؋
1FFF 8K INTERNAL
DMOVLAY =
0, 4, 5, 6, 7
ACCESSIBLE WHEN
DMOVLAY = 0
0
؋
0000– 0
؋
1FFF Program Memory, Host Mode allows access to all internal
memory. External overlay access is limited by a single external
address line (A0). External program execution is not available in
host mode due to a restricted data bus that is 16-bits wide only.
OR
EXTERNAL 8K
DMOVLAY = 1, 2
0
؋
0000– 0
؋
1FFF ACCESSIBLE WHEN
DMOVLAY = 4
0
؋
0000 0
؋
0000– 0
؋
1FFF ACCESSIBLE WHEN
DMOVLAY = 5
0
؋
0000– 0
؋
1FFF INTERNAL
MEMORY
ACCESSIBLE WHEN
DMOVLAY = 6
Table III. PMOVLAY Bits
0
؋
0000– 0
؋
1FFF ACCESSIBLE WHEN
DMOVLAY = 7
PMOVLAY Memory A13
A12:0
ACCESSIBLE WHEN
0
؋
0000– 0
؋
1FFF DMOVLAY = 1
0, 4, 5
1
Internal
External
Overlay 1
Not Applicable Not Applicable
EXTERNAL
MEMORY
ACCESSIBLE WHEN
DMOVLAY = 2
0
1
13 LSBs of Address
Between 0x2000
and 0x3FFF
13 LSBs of Address
Between 0x2000
and 0x3FFF
Figure 5. Data Memory Map
2
External
Overlay 2
–8–
REV. A
ADSP-2189M
Data Memory, Host Mode allows access to all internal
memory. External overlay access is limited by a single external
address line (A0).
I/O Space (Full Memory Mode)
The ADSP-2189M supports an additional external memory
space called I/O space. This space is designed to support simple
connections to peripherals (such as data converters and external
registers) or to bus interface ASIC data registers. I/O space
supports 2048 locations of 16-bit-wide data. The lower eleven
bits of the external address bus are used; the upper three bits are
undefined. Two instructions were added to the core ADSP-2100
Family instruction set to read from and write to I/O memory
space. The I/O space also has four dedicated three-bit wait-state
registers, IOWAIT0–3, which, in combination with the wait-
state mode bit, specify up to 15 wait-states to be automatically
generated for each of four regions. The wait-states act on ad-
dress ranges as shown in Table V.
Table IV. DMOVLAY Bits
PMOVLAY Memory A13
A12:0
0, 4, 5, 6, 7 Internal Not Applicable Not Applicable
1
2
External
Overlay 1
0
1
13 LSBs of Address
Between 0x2000
and 0x3FFF
13 LSBs of Address
Between 0x2000
and 0x3FFF
External
Overlay 2
Table V. Wait-States
Memory Mapped Registers (New to the ADSP-2189M)
The ADSP-2189M has three memory mapped registers that
differ from other ADSP-21xx Family DSPs. The slight modifi-
cations to these registers (Wait-State Control, Programmable
Flag and Composite Select Control and System Control) pro-
vide the ADSP-2189M’s wait-state and BMS control features.
Address Range
Wait-State Register
0x000–0x1FF
0x200–0x3FF
0x400–0x5FF
0x600–0x7FF
IOWAIT0 and Wait-State Mode Select Bit
IOWAIT1 and Wait-State Mode Select Bit
IOWAIT2 and Wait-State Mode Select Bit
IOWAIT3 and Wait-State Mode Select Bit
WAIT-STATE CONTROL
15 14 13 12 11 10
9
1
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
1
Composite Memory Select (CMS)
1
1
1
1
1
1
DM(0x3FFE)
The ADSP-2189M has a programmable memory select signal
that is useful for generating memory select signals for memories
mapped to more than one space. The CMS signal is generated
to have the same timing as each of the individual memory
select signals (PMS, DMS, BMS, IOMS) but can combine
their functionality.
DWAIT
IOWAIT3
IOWAIT2 IOWAIT1
IOWAIT0
WAIT STATE MODE SELECT (ADSP-2189M)
0 = NORMAL MODE (DWAIT, IOWAIT0-3 = N WAIT STATES, RANGING FROM 0 TO 7)
1 = 2N+1 MODE (DWAIT, IOWAIT0-3 = N WAIT STATES, RANGING FROM 0 TO 15)
Figure 6. Wait-State Control Register (ADSP-2189M)
When set, each bit in the CMSSEL register causes the CMS
signal to be asserted when the selected memory select is as-
serted. For example, to use a 32K word memory to act as both
program and data memory, set the PMS and DMS bits in the
CMSSEL register and use the CMS pin to drive the chip select
of the memory, and use either DMS or PMS as the additional
address bit.
PROGRAMMABLE FLAG & COMPOSITE SELECT CONTROL
15 14 13 12 11 10
9
1
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
1
1
1
1
1
1
1
DM(0x3FE6)
BMWAIT
CMSSEL
PFTYPE
(BIT-15, ADSP-2189M) 0 = DISABLE CMS
1 = ENABLE CMS
0 = INPUT
1 = OUTPUT
(WHERE BIT: 11-IOM, 10BM, 9-DM, 8-PM)
The CMS pin functions like the other memory select signals,
with the same timing and bus request logic. A 1 in the enable bit
causes the assertion of the CMS signal at the same time as the
selected memory select signal. All enable bits default to 1 at
reset, except the BMS bit.
Figure 7. Programmable Flag and Composite Select Con-
trol Register
SYSTEM CONTROL
15 14 13 12 11 10
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
1
1
1
0
1
DM(0x3FFF)
0
0
0
0
0
1
Byte Memory Select (BMS)
The ADSP-2189M’s BMS disable feature combined with the
CMS pin lets you use multiple memories in the byte memory
space. For example, an EPROM could be attached to the BMS
select, and an SRAM could be connected to CMS. Because
BMS is enabled at reset, the EPROM would be used for boot-
ing. After booting, software could disable BMS and set the
CMS signal to respond to BMS, enabling the SRAM.
RESERVED, ALWAYS = 0
(ADSP-2189M)
PWAIT
PROGRAM MEMORY
WAIT STATES
SPORT0 ENABLE
0 = DISABLE
1 = ENABLE
DISABLE BMS (ADSP-2189M)
0 = ENABLE BMS
1 = DISABLE BMS, EXCEPT WHEN MEMORY
STROBES ARE THREE-STATED
SPORT1 ENABLE
0 = DISABLE
1 = ENABLE
SPORT1 CONFIGURE
0 = FI, FO, IRQ0, IRQ1, SCLK
1 = SPORT1
Figure 8. System Control Register
REV. A
–9–
ADSP-2189M
Byte Memory
BDMA accesses can cross page boundaries during sequential
addressing. A BDMA interrupt is generated on the completion
of the number of transfers specified by the BWCOUNT register.
The byte memory space is a bidirectional, 8-bit-wide, external
memory space used to store programs and data. Byte memory is
accessed using the BDMA feature. The byte memory space
consists of 256 pages, each of which is 16K × 8.
The BWCOUNT register is updated after each transfer so it can
be used to check the status of the transfers. When it reaches
zero, the transfers have finished and a BDMA interrupt is gener-
ated. The BMPAGE and BEAD registers must not be accessed
by the DSP during BDMA operations.
The byte memory space on the ADSP-2189M supports read
and write operations as well as four different data formats. The
byte memory uses data bits 15:8 for data. The byte memory
uses data bits 23:16 and address bits 13:0 to create a 22-bit
address. This allows up to a 4 meg × 8 (32 megabit) ROM or
RAM to be used without glue logic. All byte memory accesses
are timed by the BMWAIT register and the wait-state mode bit.
The source or destination of a BDMA transfer will always be
on-chip program or data memory.
When the BWCOUNT register is written with a nonzero value
the BDMA circuit starts executing byte memory accesses with
wait-states set by BMWAIT. These accesses continue until the
count reaches zero. When enough accesses have occurred to
create a destination word, it is transferred to or from on-chip
memory. The transfer takes one DSP cycle. DSP accesses to
external memory have priority over BDMA byte memory
accesses.
Byte Memory DMA (BDMA, Full Memory Mode)
The Byte memory DMA controller allows loading and storing of
program instructions and data using the byte memory space.
The BDMA circuit is able to access the byte memory space
while the processor is operating normally and steals only one
DSP cycle per 8-, 16- or 24-bit word transferred.
The BDMA Context Reset bit (BCR) controls whether the
processor is held off while the BDMA accesses are occurring.
Setting the BCR bit to 0 allows the processor to continue opera-
tions. Setting the BCR bit to 1 causes the processor to stop
execution while the BDMA accesses are occurring, to clear the
context of the processor, and start execution at address 0 when
the BDMA accesses have completed.
BDMA CONTROL
15 14 13 12 11 10
9
8
7
6
5
0
4
0
3
1
2
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
DM (0
؋
3FE3) BTYPE
BDIR
0 = LOAD FROM BM
1 = STORE TO BM
BMPAGE
BDMA
OVERLAY
BITS
BCR
0 = RUN DURING BDMA
1 = HALT DURING BDMA
The BDMA overlay bits specify the OVLAY memory blocks to
be accessed for internal memory.
Figure 9. BDMA Control Register
The BMWAIT field, which has four bits on ADSP-2189M,
allows selection of up to 15 wait-states for BDMA transfers.
The BDMA circuit supports four different data formats which
are selected by the BTYPE register field. The appropriate num-
ber of 8-bit accesses are done from the byte memory space to
build the word size selected. Table VI shows the data formats
supported by the BDMA circuit.
Internal Memory DMA Port (IDMA Port; Host Memory
Mode)
The IDMA Port provides an efficient means of communication
between a host system and the ADSP-2189M. The port is used
to access the on-chip program memory and data memory of the
DSP with only one DSP cycle per word overhead. The IDMA
port cannot, however, be used to write to the DSP’s memory-
mapped control registers. A typical IDMA transfer process is
described as follows:
Table VI. Data Formats
Internal
BTYPE
Memory Space
Word Size
Alignment
00
01
10
11
Program Memory
Data Memory
Data Memory
Data Memory
24
16
8
Full Word
Full Word
MSBs
1. Host starts IDMA transfer.
2. Host checks IACK control line to see if the DSP is busy.
8
LSBs
3. Host uses IS and IAL control lines to latch either the DMA
starting address (IDMAA) or the PM/DM OVLAY selection
into the DSP’s IDMA control registers. If Bit 15 = 1, the
value of bits 7:0 represent the IDMA overlay: Bits 14:8 must
be set to 0. If Bit 15 = 0, the value of bits 13:0 represent the
starting address of internal memory to be accessed and Bit 14
reflects PM or DM for access.
Unused bits in the 8-bit data memory formats are filled with 0s.
The BIAD register field is used to specify the starting address
for the on-chip memory involved with the transfer. The 14-bit
BEAD register specifies the starting address for the external byte
memory space. The 8-bit BMPAGE register specifies the start-
ing page for the external byte memory space. The BDIR register
field selects the direction of the transfer. Finally, the 14-bit
BWCOUNT register specifies the number of DSP words to
transfer and initiates the BDMA circuit transfers.
4. Host uses IS and IRD (or IWR) to read (or write) DSP inter-
nal memory (PM or DM).
5. Host checks IACK line to see if the DSP has completed the
previous IDMA operation.
6. Host ends IDMA transfer.
–10–
REV. A
ADSP-2189M
The IDMA port has a 16-bit multiplexed address and data bus
and supports 24-bit program memory. The IDMA port is com-
pletely asynchronous and can be written while the ADSP-2189M
is operating at full speed.
DMA
DATA MEMORY
OVLAY
DMA
PROGRAM MEMORY
OVLAY
ALWAYS
ACCESSIBLE
AT ADDRESS
0
؋
2000 – 0؋
3FFF ALWAYS
ACCESSIBLE
AT ADDRESS
0
؋
0000 – 0؋
1FFF The DSP memory address is latched and then automatically
incremented after each IDMA transaction. An external device
can therefore access a block of sequentially addressed memory
by specifying only the starting address of the block. This in-
creases throughput as the address does not have to be sent for
each memory access.
0
؋
0000– 0
؋
1FFF ACCESSIBLE WHEN
DMOVLAY = 0
0
؋
0000– 0
؋
1FFF 0
؋
2000– 0
؋
3FFF 0
؋
2000– 0
؋
3FFF ACCESSIBLE WHEN
PMOVLAY = 0
0
؋
0000– 0
؋
1FFF ACCESSIBLE WHEN
DMOVLAY = 4
0
؋
0000– 0
؋
1FFF ACCESSIBLE WHEN
DMOVLAY = 5
0
؋
2000– 0
؋
3FFF ACCESSIBLE WHEN
PMOVLAY = 4
0
؋
0000– 0
؋
1FFF ACCESSIBLE WHEN
DMOVLAY = 6
IDMA Port access occurs in two phases. The first is the IDMA
Address Latch cycle. When the acknowledge is asserted, a 14-bit
address and 1-bit destination type can be driven onto the bus by
an external device. The address specifies an on-chip memory
location, the destination type specifies whether it is a DM or
PM access. The falling edge of the IDMA address latch signal
(IAL) or the missing edge of the IDMA select signal (IS) latches
this value into the IDMAA register.
ACCESSIBLE WHEN
PMOVLAY = 5
ACCESSIBLE WHEN
DMOVLAY = 7
NOTE: IDMA AND BDMA HAVEN SEPARATE
DMA CONTROL REGISTERS
Figure 11. Direct Memory Access—PM and DM Memory
Maps
Bootstrap Loading (Booting)
The ADSP-2189M has two mechanisms to allow automatic
loading of the internal program memory after reset. The method
for booting is controlled by the Mode A, B and C configuration
bits.
Once the address is stored, data can then be either read from, or
written to, the ADSP-2189M’s on-chip memory. Asserting the
select line (IS) and the appropriate read or write line (IRD and
IWR respectively) signals the ADSP-2189M that a particular
transaction is required. In either case, there is a one-processor-
cycle delay for synchronization. The memory access consumes
one additional processor cycle.
When the MODE pins specify BDMA booting, the ADSP-2189M
initiates a BDMA boot sequence when reset is released.
The BDMA interface is set up during reset to the following
defaults when BDMA booting is specified: the BDIR, BMPAGE,
BIAD and BEAD registers are set to 0, the BTYPE register is
set to 0 to specify program memory 24-bit words, and the
BWCOUNT register is set to 32. This causes 32 words of on-
chip program memory to be loaded from byte memory. These
32 words are used to set up the BDMA to load in the remaining
program code. The BCR bit is also set to 1, which causes pro-
gram execution to be held off until all 32 words are loaded into
on-chip program memory. Execution then begins at address 0.
Once an access has occurred, the latched address is automati-
cally incremented and another access can occur.
Through the IDMAA register, the DSP can also specify the
starting address and data format for DMA operation. Asserting
the IDMA port select (IS) and address latch enable (IAL) di-
rects the ADSP-2189M to write the address onto the IAD0-14
bus into the IDMA Control Register. If Bit 15 is set to 0, IDMA
latches the address. If Bit 15 is set to 1, IDMA latches into the
OVLAY register. This register, shown below, is memory
mapped at address DM (0x3FE0). Note that the latched address
(IDMAA) cannot be read back by the host.
The ADSP-2100 Family development software (Revision 5.02
and later) fully supports the BDMA booting feature and can
generate byte memory space compatible boot code.
Refer to the following figures for more information on IDMA
and DMA memory maps.
The IDLE instruction can also be used to allow the processor to
hold off execution while booting continues through the BDMA
interface. For BDMA accesses while in Host Mode, the ad-
dresses to boot memory must be constructed externally to the
ADSP-2189M. The only memory address bit provided by the
processor is A0.
IDMA OVERLAY
15 14 13 12 11 10
9
8
7
6
5
4
0
3
0
2
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
DM(0
؋
3FE7) DM(0
؋
3FE0) RESERVED SET TO 0
ID DMOVLAY ID PMOVLAY
IDMA Port Booting
IDMA CONTROL (U = UNDEFINED AT RESET)
The ADSP-2189M can also boot programs through its Internal
DMA port. If Mode C = 1, Mode B = 0, and Mode A = 1, the
ADSP-2189M boots from the IDMA port. IDMA feature can
load as much on-chip memory as desired. Program execution is
held off until on-chip program memory location 0 is written to.
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
IDMAA ADDRESS
IDMAD DESTINATION MEMORY TYPE:
0 = PM
1 = DM
Figure 10. IDMA Control/OVLAY Registers
REV. A
–11–
ADSP-2189M
Bus Request and Bus Grant
•
The algebraic syntax eliminates the need to remember cryp-
tic assembler mnemonics. For example, a typical arithmetic
add instruction, such as AR = AX0 + AY0, resembles a
simple equation.
The ADSP-2189M can relinquish control of the data and ad-
dress buses to an external device. When the external device
requires access to memory, it asserts the bus request (BR) sig-
nal. If the ADSP-2189M is not performing an external memory
access, it responds to the active BR input in the following pro-
cessor cycle by:
•
•
Every instruction assembles into a single, 24-bit word that
can execute in a single instruction cycle.
The syntax is a superset ADSP-2100 Family assembly language
and is completely source-and-object-code-compatible with
other family members. Programs may need to be relocated to
utilize on-chip memory and conform to the ADSP-2189M’s
interrupt vector and reset vector map.
•
Three-stating the data and address buses and the PMS,
DMS, BMS, CMS, IOMS, RD, WR output drivers,
•
•
Asserting the bus grant (BG) signal, and
Halting program execution.
•
•
Sixteen condition codes are available. For conditional jump,
call, return, or arithmetic instructions, the condition can be
checked and the operation executed in the same instruction
cycle.
If Go Mode is enabled, the ADSP-2189M will not halt program
execution until it encounters an instruction that requires an
external memory access.
If the ADSP-2189M is performing an external memory access
when the external device asserts the BR signal, it will not three-
state the memory interfaces or assert the BG signal until the
processor cycle after the access completes. The instruction does
not need to be completed when the bus is granted. If a single
instruction requires two external memory accesses, the bus will
be granted between the two accesses.
Multifunction instructions allow parallel execution of an
arithmetic instruction with up to two fetches or one write to
processor memory space during a single instruction cycle.
DESIGNING AN EZ-ICE-COMPATIBLE SYSTEM
The ADSP-2189M has on-chip emulation support and an ICE-
Port, a special set of pins that interface to the EZ-ICE. These
features allow in-circuit emulation without replacing the target
system processor by using only a 14-pin connection from the
target system to the EZ-ICE. Target systems must have a 14-pin
connector to accept the EZ-ICE’s in-circuit probe, a 14-pin
plug.
When the BR signal is released, the processor releases the BG
signal, reenables the output drivers and continues program
execution from the point at which it stopped.
The bus request feature operates at all times, including when
the processor is booting and when RESET is active.
Issuing the chip reset command during emulation causes the
DSP to perform a full chip reset, including a reset of its memory
mode. Therefore, it is vital that the mode pins are set correctly
PRIOR to issuing a chip reset command from the emulator user
interface. If you are using a passive method of maintaining
mode information (as discussed in Setting Memory Modes),
then it does not matter that the mode information is latched by
an emulator reset. However, if using the RESET pin as a
method of setting the value of the mode pins, the effects of an
emulator reset must be taken into consideration.
The BGH pin is asserted when the ADSP-2189M requires the
external bus for a memory or BDMA access, but is stopped.
The other device can release the bus by deasserting bus request.
Once the bus is released, the ADSP-2189M deasserts BG and
BGH and executes the external memory access.
Flag I/O Pins
The ADSP-2189M has eight general purpose programmable
input/output flag pins. They are controlled by two memory
mapped registers. The PFTYPE register determines the direc-
tion, 1 = output and 0 = input. The PFDATA register is used to
read and write the values on the pins. Data being read from a
pin configured as an input is synchronized to the ADSP-2189M’s
clock. Bits that are programmed as outputs will read the value
being output. The PF pins default to input during reset.
One method of ensuring that the values located on the mode
pins are those desired is to construct a circuit like the one shown
in Figure 12. This circuit forces the value located on the Mode
A pin to logic high; regardless if it latched via the RESET or
ERESET pin.
In addition to the programmable flags, the ADSP-2189M has
five fixed-mode flags, FLAG_IN, FLAG_OUT, FL0, FL1 and
FL2. FL0-FL2 are dedicated output flags. FLAG_IN and
FLAG_OUT are available as an alternate configuration of
SPORT1.
ERESET
RESET
ADSP-2189M
Note: Pins PF0, PF1, PF2 and PF3 are also used for device
configuration during reset.
1k⍀
MODE A/PFO
INSTRUCTION SET DESCRIPTION
PROGRAMMABLE I/O
The ADSP-2189M assembly language instruction set has an
algebraic syntax that was designed for ease of coding and read-
ability. The assembly language, which takes full advantage of the
processor’s unique architecture, offers the following benefits:
Figure 12. Mode A Pin/EZ-ICE Circuit
See the ADSP-2100 Family EZ-Tools data sheet for complete
information on ICE products.
–12–
REV. A
ADSP-2189M
The ICE-Port interface consists of the following ADSP-2189M
pins: EBR, EINT, EE, EBG, ECLK, ERESET, ELIN, EMS,
and ELOUT.
Target Memory Interface
For your target system to be compatible with the EZ-ICE emu-
lator, it must comply with the memory interface guidelines listed
below.
These ADSP-2189M pins must be connected only to the EZ-
ICE connector in the target system. These pins have no function
except during emulation, and do not require pull-up or pull-
down resistors. The traces for these signals between the ADSP-
2189M and the connector must be kept as short as possible, no
longer than three inches.
PM, DM, BM, IOM, and CM
Design your Program Memory (PM), Data Memory (DM),
Byte Memory (BM), I/O Memory (IOM), and Composite
Memory (CM) external interfaces to comply with worst case
device timing requirements and switching characteristics as
specified in this data sheet. The performance of the EZ-ICE
may approach published worst case specification for some memory
access timing requirements and switching characteristics.
The following pins are also used by the EZ-ICE: BR, BG,
RESET, and GND.
The EZ-ICE uses the EE (emulator enable) signal to take con-
trol of the ADSP-2189M in the target system. This causes the
processor to use its ERESET, EBR, and EBG pins instead of
the RESET, BR, and BG pins. The BG output is three-stated.
These signals do not need to be jumper-isolated in your system.
Note: If your target does not meet the worst case chip specifica-
tion for memory access parameters, you may not be able to
emulate your circuitry at the desired CLKIN frequency. De-
pending on the severity of the specification violation, you may
have trouble manufacturing your system as DSP components
statistically vary in switching characteristic and timing require-
ments within published limits.
The EZ-ICE connects to your target system via a ribbon cable
and a 14-pin female plug. The female plug is plugged onto the
14-pin connector (a pin strip header) on the target board.
Restriction: All memory strobe signals on the ADSP-2189M
(RD, WR, PMS, DMS, BMS, CMS, and IOMS) used in your
target system must have 10 kΩ pull-up resistors connected when
the EZ-ICE is being used. The pull-up resistors are necessary
because there are no internal pull-ups to guarantee their state
during prolonged three-state conditions resulting from typical
EZ-ICE debugging sessions. These resistors may be removed at
your option when the EZ-ICE is not being used.
Target Board Connector for EZ-ICE Probe
The EZ-ICE connector (a standard pin strip header) is shown in
Figure 13. You must add this connector to your target board
design if you intend to use the EZ-ICE. Be sure to allow enough
room in your system to fit the EZ-ICE probe onto the 14-pin
connector.
1
3
2
4
BG
GND
EBG
Target System Interface Signals
When the EZ-ICE board is installed, the performance on some
system signals change. Design your system to be compatible
with the following system interface signal changes introduced by
the EZ-ICE board:
BR
5
6
EBR
EINT
ELIN
ECLK
EMS
7
8
KEY (NO PIN)
ELOUT
EE
•
EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the RESET
signal.
10
12
14
9
11
13
•
•
•
•
EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the BR signal.
RESET
ERESET
TOP VIEW
EZ-ICE emulation ignores RESET and BR when single-
stepping.
Figure 13. Target Board Connector for EZ-ICE
The 14-pin, 2-row pin strip header is keyed at the Pin 7 loca-
tion—you must remove Pin 7 from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spac-
ing should be 0.1 × 0.1 inches. The pin strip header must have
at least 0.15 inch clearance on all sides to accept the EZ-ICE
probe plug.
EZ-ICE emulation ignores RESET and BR when in Emula-
tor Space (DSP halted).
EZ-ICE emulation ignores the state of target BR in certain
modes. As a result, the target system may take control of the
DSP’s external memory bus only if bus grant (BG) is as-
serted by the EZ-ICE board’s DSP.
Pin strip headers are available from vendors such as 3M,
McKenzie, and Samtec.
REV. A
–13–
ADSP-2189M–SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONS
K Grade
B Grade
Parameter
Min
Max
Min
Max
Unit
VDDINT
VDDEXT
VINPUT
2.37
2.37
VIL = –0.3
2.63
3.6
VIH = 3.6
+70
2.25
2.25
–0.03
–40
2.75
3.6
3.6
V
V
V
°C
1
TAMB
0
+85
NOTES
1The ADSP-2189M is 3.3 V tolerant (always accepts up to 3.6 Volt max VIH), but voltage compliance (on outputs, VOH) depends on the input VDDEXT; because VOH
(max) ≈ VDDEXT (max). This applies to Bidirectional pins (D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, A1–A13, PF0–PF7) and Input Only pins (CLKIN,
RESET, BR, DR0, DR1, PWD).
ELECTRICAL CHARACTERISTICS
K/B Grades
Parameter
Test Conditions
Min
Typ
Max
Unit
VIH, Hi-Level Input Voltage1, 2
VIH, Hi-Level CLKIN Voltage
VIL, Lo-Level Input Voltage1, 3
@ VDDINT = max
@ VDDINT = max
@ VDDINT = min
1.5
2.0
V
V
V
V
V
V
V
µA
µA
µA
µA
mA
mA
0.6
V
OH, Hi-Level Output Voltage1, 4 , 5
@ VDDEXT = min, IOH = –0.5 mA
@ VDDEXT = 3.0 V, IOH = –0.5 mA
@ VDDEXT = min, IOH = –100 µA6
@ VDDEXT = min, IOL = 2 mA
@ VDDINT = max, VIN = 3.6 V
@ VDDINT = max, VIN = 0 V
@ VDDINT = max, VIN = 3.6 V8
@ VDDINT = max, VIN = 0 V8
@ VDDINT = 2.5, tCK = 15 ns
@ VDDINT = 2.5, tCK = 13.3 ns
@ VDDINT = 2.5, tCK = 15 ns11,
2.0
2.4
VDDEXT – 0.3
V
OL, Lo-Level Output Voltage1, 4, 5
0.4
10
10
10
10
IIH, Hi-Level Input Current3
IIL, Lo-Level Input Current3
I
OZH, Three-State Leakage Current7
IOZL, Three-State Leakage Current7
I
I
DD, Supply Current (Idle)9
DD, Supply Current (Idle)9
9
10
IDD, Supply Current (Dynamic)10
T
AMB = +25°C
32
mA
I
I
DD, Supply Current (Dynamic)10
@ VDDINT = 2.5, tCK = 13.3 ns11,
TAMB = +25°C
36
150
mA
µA
DD, Supply Current (Power-Down)12, 15
Lowest Power Mode
@ VIN = 2.5 V,
CI, Input Pin Capacitance3, 6, 13
fIN = 1.0 MHz,
T
AMB = +25°C
8
8
pF
pF
CO, Output Pin Capacitance6, 7, 12, 14
@ VIN = 2.5 V,
fIN = 1.0 MHz,
TAMB = +25°C
NOTES
1Bidirectional pins: D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, A1–A13, PF0–PF7.
2Input Only pins: RESET, BR, DR0, DR1, PWD.
3Input Only pins: CLKIN, RESET, BR, DR0, DR1, PWD.
4Output pins: BG, PMS, DMS, BMS, IOMS, CMS, RD, WR, PWDACK, A0, DT0, DT1, CLKOUT, FL2-0, BGH.
5Although specified for TTL outputs, all ADSP-2189M outputs are CMOS-compatible and will drive to VDDEXT and GND, assuming no dc loads.
6Guaranteed but not tested.
7Three-statable pins: A0–A13, D0-D23, PMS, DMS, BMS, IOMS, CMS, RD, WR, DT0, DT1, SCLK0, SCLK1, TFS0, TFS1, RFS0, RFS1, PF0–PF7.
80 V on BR.
9Idle refers to ADSP-2189M state of operation during execution of IDLE instruction. Deasserted pins are driven to either V DD or GND.
10
I
measurement taken with all instructions executing from internal memory. 50% of the instructions are multifunction (types 1, 4, 5, 12, 13, 14), 30% are type 2
DD
and type 6, and 20% are idle instructions.
11
V
= 0 V and 3 V. For typical figures for supply currents, refer to Power Dissipation section.
IN
12 See Chapter 9 of the ADSP-2100 Family User’s Manual, Third Edition for details.
13 Applies to LQFP package type.
14 Output pin capacitance is the capacitive load for any three-stated output pin.
15
V
DDINT
= 2.5 V. T = 25°C.
Specifications subject to change without notice.
–14–
REV. A
ADSP-2189M
ABSOLUTE MAXIMUM RATINGS1
Parameter
Value
Min Max
Internal Supply Voltage (VDDINT
)
–0.3 V +3.0 V
External Supply Voltage (VDDEXT
)
–0.3 V +4.6 V
–0.5 V +4.6 V
–0.5 V VDDEXT + 0.5 V
Input Voltage2
Output Voltage Swing3
Operating Temperature Range (Ambient) –40°C +85°C
Storage Temperature Range
Lead Temperature (5 sec) LQFP
–65°C +150°C
+280°C
NOTES
1Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. These are stress ratings only; functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2Applies to Bidirectional pins (D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0,
TFS1, A1–A13, PF0–PF7) and Input only pins (CLKIN, RESET, BR, DR0,
DR1, PWD).
3AppliestoOutputpins(BG,PMS,DMS, BMS,IOMS, CMS,RD,WR, PWDACK,
A0, DT0, DT1, CLKOUT, FL2-0, BGH).
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADSP-2189M features proprietary ESD protection circuitry, permanent damage
may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
MEMORY TIMING SPECIFICATIONS
TIMING PARAMETERS
The table below shows common memory device specifications
and the corresponding ADSP-2189M timing parameters, for
your convenience.
GENERAL NOTES
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results for
an individual device, the values given in this data sheet reflect
statistical variations and worst cases. Consequently, you cannot
meaningfully add up parameters to derive longer times.
Memory
Device
Specification
Timing
Parameter
Parameter Definition1
Address Setup to
Write Start
tASW
A0–A13, xMS Setup before
WR Low
TIMING NOTES
Address Setup to
Write End
tAW
A0–A13, xMS Setup before
WR Deasserted
Switching characteristics specify how the processor changes its
signals. You have no control over this timing—circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use
switching characteristics to ensure that any timing requirement
of a device connected to the processor (such as memory) is
satisfied.
Address Hold Time tWRA
A0–A13, xMS Hold before
WR Low
Data Setup Time
tDW
Data Setup before WR
High
Data Hold Time
OE to Data Valid
tDH
tRDD
Data Hold after WR High
RD Low to Data Valid
Timing requirements apply to signals that are controlled by
circuitry external to the processor, such as the data input for a
read operation. Timing requirements guarantee that the proces-
sor operates correctly with other devices.
Address Access Time tAA
A0–A13, xMS to Data Valid
NOTE
1xMS = PMS, DMS, BMS, CMS or IOMS.
REV. A
–15–
ADSP-2189M
FREQUENCY DEPENDENCY FOR TIMING
Output Drive Currents
SPECIFICATIONS
Figure 14 shows typical I-V characteristics for the output drivers
on the ADSP-2189M. The curves represent the current drive
capability of the output drivers as a function of output voltage.
tCK is defined as 0.5tCKI. The ADSP-2189M uses an input clock
with a frequency equal to half the instruction rate: a 37.50 MHz
input clock (which is equivalent to 28 ns) yields a 13 ns proces-
sor cycle (equivalent to 75 MHz). tCK values within the range of
0.5tCKI period should be substituted for all relevant timing pa-
rameters to obtain the specification value.
80
V
60
40
OH
V
= 3.6V @ –40؇C
= 3.3V @ +25؇C
DDEXT
Example: tCKH = 0.5tCK – 7 ns = 0.5 (15 ns) – 7 ns = 0.5 ns
V
DDEXT
20
ENVIRONMENTAL CONDITIONS1
V
= 2.5V @ +85؇C
DDEXT
0
Rating Description
Symbol
Value
–20
–40
V
= 3.6V @ –40؇C
DDEXT
Thermal Resistance
(Case-to-Ambient)
(Junction-to-Ambient)
(Junction-to-Case)
θCA
θJA
θJC
48°C/W
50°C/W
2°C/W
V
= 2.5V @ +85؇C
DDEXT
V
OL
V
= 3.3V @ +25؇C
DDEXT
–60
–80
NOTE
1Where the ambient temperature rating (TAMB) is:
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
SOURCE VOLTAGE – V
TAMB = TCASE – (PD × θCA
)
TCASE = Case temperature in °C
Figure 14. Typical Output Driver Characteristics
PD = Power dissipation in W.
POWER DISSIPATION
To determine total power dissipation in a specific application,
the following equation should be applied for each output:
C × VDD2 × f
C = load capacitance, f = output switching frequency.
Example:
In an application where external data memory is used and no
other outputs are active, power dissipation is calculated as follows:
Assumptions:
•
External data memory is accessed every cycle with 50% of
the address pins switching.
•
External data memory writes occur every other cycle with
50% of the data pins switching.
•
•
Each address and data pin has a 10 pF total load at the pin.
The application operates at VDDEXT = 3.3 V and tCK = 15 ns.
Total Power Dissipation = PINT + (C × VDDEXT2 × f)
P
INT = internal power dissipation from Power vs. Frequency
graph (Figure 15).
(C × VDDEXT2 × f) is calculated for each output:
# of
Pins C
؋
؋
؋
f
2
Parameters
VDDEXT
PD
Address, DMS
Data Output, WR 9
RD
CLKOUT
8
10 pF 3.32 V
10 pF 3.32 V
10 pF 3.32 V
10 pF 3.32 V
33.3 MHz
16.67 MHz 16.3 mW
16.67 MHz
33.3 MHz
29.0 mW
1
1
1.8 mW
3.6 mW
50.7 mW
Total power dissipation for this example is PINT + 50.7 mW.
–16–
REV. A
ADSP-2189M
CAPACITIVE LOADING
Figure 16 and Figure 17 show the capacitive loading character-
istics of the ADSP-2189M.
1, 2, 3
2189L POWER, INTERNAL
115
110
105
100
110mW
V
= 2.65V
DD
30
95mW
82mW
T = +85؇C
95
90
85
V
= 0V TO 2.0V
DD
25
V
= 2.5V
DD
82mW
80
75
70
65
60
55
V
= 2.35V
20
15
10
5
DD
70mW
61mW
50
55
60
65
70
75
80
1/t – MHz
CK
1, 2, 4
POWER, IDLE
30
28
26
24
22
20
18
16
14
28mW
24mW
0
50
0
100
150
– pF
200
250
300
V
= 2.65V
DD
C
L
24mW
20mW
Figure 16. Typical Output Rise Time vs. Load Capacitance,
CL (at Maximum Ambient Operating Temperature)
V
= 2.5V
DD
20mW
18
V
= 2.35V
DD
16
14
16.5mW
12
10
40
55
60
65
70
75
80
1/t – MHz
8
CK
6
4
2
POWER, IDLE n MODES
26
24mW
IDLE
2
24
22
20
18
16
V
= 2.65V
DD
NOMINAL
–2
–4
–6
20mW
0
50
100
150
200
250
C
– pF
L
16.4mW
15.7mW
V
V
= 2.5V
= 2.35V
65
DD
IDLE (16)
Figure 17. Typical Output Valid Delay or Hold vs. Load
Capacitance, CL (at Maximum Ambient Operating
Temperature)
15mW
IDLE (128)
14
12
DD
14.25mW
50
55
60
70
75
80
900
1/t – MHz
CK
VALID FOR ALL TEMPERATURE GRADES.
1
772A
475A
800
700
TEMP = +85؇C
POWER REFLECTS DEVICE OPERATING WITH NO OUTPUT LOADS.
657A
393A
2
TYPICAL POWER DISSIPATION AT 2.5V V
WHERE SPECIFIED.
AND +25؇C EXCEPT
DDINT
3
I
MEASUREMENT TAKEN WITH ALL INSTRUCTIONS EXECUTING FROM
600
500
DD
INTERNAL MEMORY. 50% OF THE INSTRUCTIONS ARE MULTIFUNCTION
(TYPES 1, 4, 5, 12, 13, 14), 30% ARE TYPE 2 AND TYPE 6, AND 20% ARE
IDLE INSTRUCTIONS.
TEMP = +70؇C
TEMP = +25؇C
4
IDLE REFERS TO ADSP-2189M STATE OF OPERATION DURING EXECUTION
400
300
OF IDLE INSTRUCTION. DEASSERTED PINS ARE DRIVEN TO EITHER V
OR GND.
DD
161A
200
100
0
Figure 15. Power vs. Frequency
131A
2.25
2.35
2.5
2.65
2.75
V
INTERNAL – Volts
DD
Figure 18. IDD Power-Down
REV. A
–17–
ADSP-2189M
driving. The output enable time (tENA) is the interval from when
a reference signal reaches a high or low voltage level to when the
output has reached a specified high or low trip point, as shown
in the Output Enable/Disable diagram. If multiple pins (such as
the data bus) are enabled, the measurement value is that of the
first pin to start driving.
TEST CONDITIONS
Output Disable Time
Output pins are considered to be disabled when they have
stopped driving and started a transition from the measured
output high or low voltage to a high impedance state. The out-
put disable time (tDIS) is the difference of tMEASURED and tDECAY
,
as shown in the Output Enable/Disable diagram. The time is the
interval from when a reference signal reaches a high or low
voltage level to when the output voltages have changed by 0.5 V
from the measured output high or low voltage.
REFERENCE
SIGNAL
tMEASURED
tDIS
tENA
V
V
OH
(MEASURED)
OH
The decay time, tDECAY, is dependent on the capacitive load,
CL, and the current load, iL, on the output pin. It can be ap-
proximated by the following equation:
(MEASURED)
V
V
(MEASURED) – 0.5V
2.0V
1.0V
OH
OUTPUT
(MEASURED) +0.5V
OL
V
V
OL
OL
CL × 0.5 V
tDECAY
(MEASURED)
tDECAY
=
(MEASURED)
iL
OUTPUT
STARTS
DRIVING
OUTPUT STOPS
DRIVING
from which
HIGH-IMPEDANCE STATE. TEST CONDITIONS CAUSE
THIS VOLTAGE LEVEL TO BE APPROXIMATELY 1.5V.
t
DIS = tMEASURED – tDECAY
is calculated. If multiple pins (such as the data bus) are disabled,
the measurement value is that of the last pin to stop driving.
Figure 20. Output Enable/Disable
I
OL
INPUT
1.5V
2.0V
TO
OUTPUT
PIN
+1.5V
OUTPUT
1.5V
0.8V
50pF
Figure 19. Voltage Reference Levels for AC Measurements
(Except Output Enable/Disable)
I
Output Enable Time
OH
Output pins are considered to be enabled when they have made
a transition from a high impedance state to when they start
Figure 21. Equivalent Device Loading for AC Measure-
ments (Including All Fixtures)
–18–
REV. A
ADSP-2189M
TIMING PARAMETERS
Parameter
Min
Max
Unit
Clock Signals and Reset
Timing Requirements:
tCKI
tCKIL
tCKIH
CLKIN Period
CLKIN Width Low
CLKIN Width High
26.6
13
13
80
ns
ns
ns
Switching Characteristics:
tCKL
tCKH
tCKOH
CLKOUT Width Low
CLKOUT Width High
CLKIN High to CLKOUT High
0.5tCK – 2
0.5tCK – 2
0
ns
ns
ns
13
Control Signals
Timing Requirements:
1
tRSP
tMS
tMH
RESET Width Low
Mode Setup before RESET High
Mode Hold after RESET High
5tCK
2
5
ns
ns
ns
NOTE
1Applies after power-up sequence is complete. Internal phase lock loop requires no more than 2000 CLKIN cycles assuming stable CLKIN (not including crystal
oscillator start-up time).
tCKI
tCKIH
CLKIN
tCKIL
tCKOH
tCKH
CLKOUT
tCKL
PF(3:0)*
tMH
tMS
RESET
*PF3 IS MODE D, PF2 IS MODE C, PF0 IS MODE A
Figure 22. Clock Signals
REV. A
–19–
ADSP-2189M
Parameter
Min
Max
Unit
Interrupts and Flags
Timing Requirements:
tIFS
tIFH
IRQx, FI, or PFx Setup before CLKOUT Low1, 2, 3, 4
IRQx, FI, or PFx Hold after CLKOUT High1, 2, 3, 4
0.25tCK + 10
0.25tCK
ns
ns
Switching Characteristics:
tFOH
tFOD
Flag Output Hold after CLKOUT Low5
Flag Output Delay from CLKOUT Low5
0.5tCK – 5
ns
ns
0.5tCK + 4
NOTES
1If IRQx and FI inputs meet tIFS and tIFH setup/hold requirements, they will be recognized during the current clock cycle; otherwise the signals will be recognized on
the following cycle. (Refer to Interrupt Controller Operation in the Program Control chapter of the ADSP-2100 Family User’s Manual, Third Edition, for further
information on interrupt servicing.)
2Edge-sensitive interrupts require pulsewidths greater than 10 ns; level-sensitive interrupts must be held low until serviced.
3IRQx = IRQ0, IRQ1, IRQ2, IRQL0, IRQL1, IRQLE.
4PFx = PF0, PF1, PF2, PF3, PF4, PF5, PF6, PF7.
5Flag Outputs = PFx, FL0, FL1, FL2, Flag_out4.
tFOD
CLKOUT
tFOH
FLAG
OUTPUTS
tIFH
IRQx
FI
PFx
tIFS
Figure 23. Interrupts and Flags
–20–
REV. A
ADSP-2189M
Parameter
Min
Max
Unit
Bus Request–Bus Grant
Timing Requirements:
tBH
tBS
BR Hold after CLKOUT High1
BR Setup before CLKOUT Low1
0.25tCK + 2
0.25tCK + 10
ns
ns
Switching Characteristics:
tSD
CLKOUT High to xMS, RD, WR Disable
xMS, RD, WR Disable to BG Low
BG High to xMS, RD, WR Enable
xMS, RD, WR Enable to CLKOUT High
xMS, RD, WR Disable to BGH Low2
BGH High to xMS, RD, WR Enable2
0.25tCK + 8
ns
ns
ns
ns
ns
ns
tSDB
tSE
tSEC
tSDBH
tSEH
0
0
0.25tCK – 3
0
0
NOTES
xMS = PMS, DMS, CMS, IOMS, BMS
1BR is an asynchronous signal. If BR meets the setup/hold requirements, it will be recognized during the current clock cycle; otherwise the signal will be recognized on
the following cycle. Refer to the ADSP-2100 Family User’s Manual, Third Edition, for BR/BG cycle relationships.
2BGH is asserted when the bus is granted and the processor or BDMA requires control of the bus to continue.
tBH
CLKOUT
BR
tBS
CLKOUT
PMS, DMS
BMS, RD
WR
tSD
tSEC
BG
tSDB
tSE
BGH
tSDBH
tSEH
Figure 24. Bus Request–Bus Grant
REV. A
–21–
ADSP-2189M
Parameter
Min
Max
Unit
Memory Read
Timing Requirements:
tRDD
tAA
tRDH
RD Low to Data Valid
A0–A13, xMS to Data Valid
Data Hold from RD High
0.5tCK – 5 + w
0.75tCK – 6 + w
ns
ns
ns
0
Switching Characteristics:
tRP
tCRD
tASR
tRDA
tRWR
RD Pulsewidth
0.5tCK – 3 + w
0.25tCK – 2
0.25tCK – 3
0.25tCK – 3
0.5tCK – 3
ns
ns
ns
ns
ns
CLKOUT High to RD Low
A0–A13, xMS Setup before RD Low
A0–A13, xMS Hold after RD Deasserted
RD High to RD or WR Low
0.25tCK + 4
w = wait-states × tCK
.
xMS = PMS, DMS, CMS, IOMS, BMS.
CLKOUT
A0 – A13
DMS, PMS,
BMS, IOMS,
CMS
tRDA
RD
D
tASR
tCRD
tRP
tRWR
tRDD
tRDH
tAA
WR
Figure 25. Memory Read
–22–
REV. A
ADSP-2189M
Parameter
Min
Max
Unit
Memory Write
Switching Characteristics:
tDW
tDH
tWP
tWDE
tASW
tDDR
tCWR
tAW
tWRA
tWWR
Data Setup before WR High
Data Hold after WR High
WR Pulsewidth
WR Low to Data Enabled
A0–A13, xMS Setup before WR Low
Data Disable before WR or RD Low
CLKOUT High to WR Low
A0–A13, xMS, Setup before WR Deasserted
A0–A13, xMS Hold after WR Deasserted
WR High to RD or WR Low
0.5tCK – 4 + w
0.25tCK – 1
0.5tCK – 3 + w
0
0.25tCK – 3
0.25tCK – 3
0.25tCK – 2
0.75tCK – 5 + w
0.25tCK – 1
0.5tCK – 3
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
0.25tCK + 4
w = wait-states × tCK
.
xMS = PMS, DMS, CMS, IOMS, BMS.
CLKOUT
A0–A13
DMS, PMS,
BMS, CMS,
IOMS
tWRA
WR
tWWR
tASW
tWP
tAW
tDH
tDDR
tCWR
D
tDW
tWDE
RD
Figure 26. Memory Write
REV. A
–23–
ADSP-2189M
Parameter
Min
Max
Unit
Serial Ports
Timing Requirements:
tSCK
tSCS
tSCH
tSCP
SCLK Period
26.67
4
7
12
ns
ns
ns
ns
DR/TFS/RFS Setup before SCLK Low
DR/TFS/RFS Hold after SCLK Low
SCLKIN Width
Switching Characteristics:
tCC
tSCDE
tSCDV
tRH
CLKOUT High to SCLKOUT
SCLK High to DT Enable
SCLK High to DT Valid
TFS/RFSOUT Hold after SCLK High
TFS/RFSOUT Delay from SCLK High
DT Hold after SCLK High
TFS (Alt) to DT Enable
TFS (Alt) to DT Valid
SCLK High to DT Disable
RFS (Multichannel, Frame Delay Zero) to DT Valid
0.25tCK
0
0.25tCK + 6
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
12
12
0
tRD
tSCDH
tTDE
tTDV
tSCDD
tRDV
0
0
12
12
12
CLKOUT
tCC
tCC
tSCK
SCLK
tSCP
tSCP
tSCS
tSCH
DR
TFS
RFS
IN
IN
tRD
tRH
RFS
TFS
OUT
OUT
tSCDD
tSCDV
tSCDH
tSCDE
DT
tTDE
tTDV
TFS
OUT
ALTERNATE
FRAME MODE
tRDV
RFS
OUT
MULTICHANNEL
MODE,
FRAME DELAY 0
(MFD = 0)
tTDE
tTDV
TFS
IN
ALTERNATE
FRAME MODE
tRDV
RFS
IN
MULTICHANNEL
MODE,
FRAME DELAY 0
(MFD = 0)
Figure 27. Serial Ports
–24–
REV. A
ADSP-2189M
Parameter
Min
Max
Unit
IDMA Address Latch
Timing Requirements:
tIALP
tIASU
tIAH
tIKA
tIALS
tIALD
Duration of Address Latch1, 2
10
5
3
0
3
ns
ns
ns
ns
ns
ns
IAD15–0 Address Setup before Address Latch End2
IAD15–0 Address Hold after Address Latch End2
IACK Low before Start of Address Latch2, 3
Start of Write or Read after Address Latch End2, 3
Address Latch Start after Address Latch End1, 2
2
NOTES
1Start of Address Latch = IS Low and IAL High.
2End of Address Latch = IS High or IAL Low.
3Start of Write or Read = IS Low and IWR Low or IRD Low.
IACK
tIKA
tIALD
IAL
tIALP
tIALP
IS
IAD15–0
tIASU
tIASU
tIAH
tIAH
tIALS
RD OR WR
Figure 28. IDMA Address Latch
REV. A
–25–
ADSP-2189M
Parameter
Min
Max
Unit
IDMA Write, Short Write Cycle
Timing Requirements:
tIKW
tIWP
tIDSU
tIDH
IACK Low before Start of Write1
0
10
3
ns
ns
ns
ns
Duration of Write1, 2
IAD15–0 Data Setup before End of Write2, 3, 4
IAD15–0 Data Hold after End of Write2, 3, 4
2
Switching Characteristics:
tIKHW
Start of Write to IACK High
10
ns
NOTES
1Start of Write = IS Low and IWR Low.
2End of Write = IS High or IWR High.
3If Write Pulse ends before IACK Low, use specifications tIDSU, tIDH.
4If Write Pulse ends after IACK Low, use specifications tIKSU, tIKH.
tIKW
IACK
tIKHW
IS
tIWP
IWR
tIDH
tIDSU
DATA
IAD 15–0
Figure 29. IDMA Write, Short Write Cycle
–26–
REV. A
ADSP-2189M
Parameter
Min
Max
Unit
IDMA Write, Long Write Cycle
Timing Requirements:
tIKW
tIKSU
tIKH
IACK Low before Start of Write1
0
ns
ns
ns
IAD15–0 Data Setup before End of Write2, 3, 4
IAD15–0 Data Hold after End of Write2, 3, 4
0.5tCK + 5
0
Switching Characteristics:
tIKLW
tIKHW
Start of Write to IACK Low4
Start of Write to IACK High
1.5tCK
ns
ns
10
NOTES
1Start of Write = IS Low and IWR Low.
2If Write Pulse ends before IACK Low, use specifications tIDSU, tIDH
.
3If Write Pulse ends after IACK Low, use specifications tIKSU, tIKH
.
4This is the earliest time for IACK Low from Start of Write. For IDMA Write cycle relationships, please refer to the ADSP-2100 Family User’s Manual, Third Edition.
tIKW
IACK
tIKHW
tIKLW
IS
IWR
tIKSU
tIKH
DATA
IAD15–0
Figure 30. IDMA Write, Long Write Cycle
REV. A
–27–
ADSP-2189M
Parameter
Min
Max
Unit
IDMA Read, Long Read Cycle
Timing Requirements:
tIKR
tIRK
IACK Low before Start of Read1
0
2
ns
ns
End of Read after IACK Low2
Switching Characteristics:
tIKHR
tIKDS
tIKDH
tIKDD
tIRDE
tIRDV
tIRDH1
tIRDH2
IACK High after Start of Read1
10
ns
ns
ns
ns
ns
ns
ns
ns
IAD15–0 Data Setup before IACK Low
0.5tCK – 2
0
IAD15–0 Data Hold after End of Read2
IAD15–0 Data Disabled after End of Read2
IAD15–0 Previous Data Enabled after Start of Read
IAD15–0 Previous Data Valid after Start of Read
IAD15–0 Previous Data Hold after Start of Read (DM/PM1)3
IAD15–0 Previous Data Hold after Start of Read (PM2)4
10
11
0
2tCK – 3
tCK – 5
NOTES
1Start of Read = IS Low and IRD Low.
2End of Read = IS High or IRD High.
3DM read or first half of PM read.
4Second half of PM read.
IACK
IS
tIKHR
tIKR
tIRK
IRD
tIKDH
tIKDS
tIRDE
PREVIOUS
DATA
READ
DATA
IAD15–0
tIRDV
tIKDD
tIRDH
Figure 31. IDMA Read, Long Read Cycle
–28–
REV. A
ADSP-2189M
Parameter
Min
Max
Unit
IDMA Read, Short Read Cycle
Timing Requirements:
tIKR
tIRP
IACK Low before Start of Read1
Duration of Read
0
10
ns
ns
Switching Characteristics:
tIKHR
tIKDH
tIKDD
tIRDE
tIRDV
IACK High after Start of Read1
10
10
10
ns
ns
ns
ns
ns
IAD15–0 Data Hold after End of Read2
IAD15–0 Data Disabled after End of Read2
IAD15–0 Previous Data Enabled after Start of Read
IAD15–0 Previous Data Valid after Start of Read
0
0
NOTES
1Start of Read = IS Low and IRD Low.
2End of Read = IS High or IRD High.
IACK
IS
tIKR
tIKHR
tIRP
IRD
tIKDH
tIRDE
PREVIOUS
DATA
IAD15–0
tIKDD
tIRDV
Figure 32. IDMA Read, Short Read Cycle
REV. A
–29–
ADSP-2189M
100-Lead LQFP Package Pinout
75
74
73
72
71
70
69
68
67
66
65
A4/IAD3
A5/IAD4
1
2
D15
D14
PIN 1
IDENTIFIER
GND
A6/IAD5
A7/IAD6
3
4
D13
D12
5
GND
6
A8/IAD7
A9/IAD8
D11
D10
7
8
A10/IAD9
D9
V
9
A11/IAD10
A12/IAD11
DDEXT
10
GND
11
12
A13/IAD12
GND
D8
64 D7/IWR
ADSP-2189M
TOP VIEW
(Not to Scale)
63
62
61
60
59
58
57
13
14
15
16
17
18
19
20
21
22
23
24
25
D6/IRD
D5/IAL
D4/IS
GND
CLKIN
XTAL
V
DDEXT
CLKOUT
GND
V
DDINT
D3/IACK
V
DDINT
D2/IAD15
WR
RD
56 D1/IAD14
55
54
53
52
51
BMS
DMS
PMS
IOMS
CMS
D0/IAD13
BG
EBG
BR
EBR
–30–
REV. A
ADSP-2189M
The ADSP-2189M package pinout appears in the following table. Pin names in bold text replace the plain text named functions
when Mode C = 1. A + sign separates two functions when either function can be active for either major I/O mode. Signals enclosed
in brackets [ ] are state bits latched from the value of the pin at the deassertion of RESET.
PIN CONFIGURATION
LQFP
Number
LQFP
Number Pin Name
LQFP
Number Pin Name
LQFP
Number Pin Name
Pin Name
1
2
3
4
5
6
7
8
A4/IAD3
A5/IAD4
GND
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
IRQE + PF4
IRQL0 + PF5
GND
IRQL1 + PF6
IRQ2 + PF7
DT0
TFS0
RFS0
DR0
SCLK0
VDDEXT
DT1
TFS1
RFS1
DR1
GND
SCLK1
ERESET
RESET
EMS
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
EBR
BR
EBG
BG
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
D16
D17
D18
D19
GND
D20
D21
D22
D23
FL2
FL1
FL0
PF3 [Mode D]
PF2 [Mode C]
VDDEXT
PWD
A6/IAD5
A7/IAD6
A8/IAD7
A9/IAD8
A10/IAD9
A11/IAD10
A12/IAD11
A13/IAD12
GND
CLKIN
XTAL
VDDEXT
CLKOUT
GND
VDDINT
WR
D0/IAD13
D1/IAD14
D2/IAD15
D3/IACK
VDDINT
GND
D4/IS
D5/IAL
D6/IRD
D7/IWR
D8
GND
VDDEXT
D9
D10
D11
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
GND
PF1 [Mode B]
PF0 [Mode A]
BGH
PWDACK
A0
A1/IAD0
A2/IAD1
A3/IAD2
RD
BMS
DMS
PMS
IOMS
CMS
EE
GND
D12
D13
D14
D15
ECLK
ELOUT
ELIN
EINT
REV. A
–31–
ADSP-2189M
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
100-Lead Metric Thin Plastic Quad Flatpack
(ST-100)
0.638 (16.20)
0.630 (16.00) TYP SQ
0.622 (15.80)
0.553 (14.05)
0.551 (14.00) TYP SQ
0.549 (13.95)
0.063 (1.60) MAX
0.472 (12.00) BSC
0.030 (0.75)
0.024 (0.60) TYP
0.020 (0.50)
100
1
76
75
12؇
TYP
SEATING
PLANE
TOP VIEW
(PINS DOWN)
0.003
(0.08)
MAX LEAD
COPLANARITY
25
26
51
50
6؇ 4؇
0؇ – 7؇
0.007 (0.177)
0.005 (0.127) TYP
0.003 (0.077)
0.020 (0.50)
0.011 (0.27)
0.009 (0.22) TYP
0.007 (0.17)
BSC
LEAD PITCH
LEAD WIDTH
NOTE:
THE ACTUAL POSITION OF EACH LEAD IS WITHIN (0.08) 0.0032 FROM
ITS IDEAL POSITION WHEN MEASURED IN THE LATERAL DIRECTION.
CENTER FIGURES ARE TYPICAL UNLESS OTHERWISE NOTED
ORDERING GUIDE
Part Number
Ambient Temperature Range
Instruction Rate
Package Description*
Package Option
ADSP-2189MKST-300
ADSP-2189MBST-266
0°C to +70°C
–40°C to +85°C
75 MHz
66 MHz
100-Lead LQFP
100-Lead LQFP
ST-100
ST-100
*In 1998, JEDEC reevaluated the specifications for the TQFP package designation, assigning it to packages 1.0 mm thick. Previously labelled TQFP packages
(1.6 mm thick) are now designated as LQFP.
–32–
REV. A
相关型号:
ADSP-2189MKST-300X
IC 24-BIT, 75 MHz, OTHER DSP, PQFP100, METRIC, PLASTIC, LQFP-100, Digital Signal Processor
ADI
©2020 ICPDF网 联系我们和版权申明