ADP3118JRZ [ADI]
Dual Bootstrapped 12 V MOSFET Driver with Output Disable; 双自举12 V MOSFET驱动器输出禁用型号: | ADP3118JRZ |
厂家: | ADI |
描述: | Dual Bootstrapped 12 V MOSFET Driver with Output Disable |
文件: | 总16页 (文件大小:431K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Dual Bootstrapped 12 V MOSFET
Driver with Output Disable
ADP3118
FEATURES
GENERAL DESCRIPTION
Optimized for low gate charge MOSFETs
All-in-one synchronous buck driver
Bootstrapped high-side drive
One PWM signal generates both drives
Anticross-conduction protection circuitry
The ADP3118 is a dual high voltage MOSFET driver optimized
for driving two N-channel MOSFETs, which are the two switches
in a nonisolated synchronous buck power converter. Each of the
drivers is capable of driving a 3000 pF load with a 25 ns
propagation delay and a 25 ns transition time. One of the drivers
can be bootstrapped and is designed to handle the high voltage
slew rate associated with floating high-side gate drivers. The
ADP3118 includes overlapping drive protection to prevent
shoot-through current in the external MOSFETs.
Output disable control turns off both MOSFETs
to float output per Intel® VRM 10 specification
APPLICATIONS
Multiphase desktop CPU supplies
Single-supply synchronous buck converters
OD
The
pin shuts off both the high-side and the low-side
MOSFETs to prevent rapid output capacitor discharge during
system shutdown.
The ADP3118 is specified over the commercial temperature
range of 0°C to 85°C and is available in 8-lead SOIC package.
SIMPLIFIED FUNCTIONAL BLOCK DIAGRAM
V
12V
IN
D1
VCC
4
BST
ADP3118
1
8
C
BST2
C
BST1
2
R
G
IN
DRVH
Q1
DELAY
R
BST
TO
INDUCTOR
SW
7
CMP
VCC
6
CMP
DRVL
PGND
1V
CONTROL
LOGIC
5
6
Q2
DELAY
3
OD
Figure 1.
Flex-Mode™ is Protected by U.S. Patent 6683441
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2005 Analog Devices, Inc. All rights reserved.
ADP3118
TABLE OF CONTENTS
Specifications..................................................................................... 3
Application Information................................................................ 10
Supply Capacitor Selection ....................................................... 10
Bootstrap Circuit........................................................................ 10
MOSFET Selection..................................................................... 10
High-Side (Control) MOSFETs................................................ 10
Low-Side (Synchronous) MOSFETs ........................................ 11
PC Board Layout Considerations............................................. 11
Outline Dimensions....................................................................... 13
Ordering Guide .......................................................................... 13
Absolute Maximum Ratings............................................................ 4
ESD Caution.................................................................................. 4
Pin Configuration and Function Descriptions............................. 5
Timing Characteristics..................................................................... 6
Typical Performance Characteristics ............................................. 7
Theory of Operation ........................................................................ 9
Low-Side Driver............................................................................ 9
High-Side Driver .......................................................................... 9
Overlap Protection Circuit.......................................................... 9
REVISION HISTORY
4/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADP3118
SPECIFICATIONS1
VCC = 12 V, BST = 4 V to 26 V, TA = 0°C to 85°C, unless otherwise noted.
Table 1.
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
PWM INPUT
Input Voltage High
Input Voltage Low
Input Current
2.0
V
V
µA
mV
0.8
+1
−1
90
Hysteresis
250
OD INPUT
Input Voltage High
Input Voltage Low
Input Current
Hysteresis
Propagation Delay Times2
2.0
V
V
µA
mV
ns
ns
0.8
+1
−1
90
250
20
40
tpdlOD
tpdhOD
See Figure 3
See Figure 3
35
55
HIGH-SIDE DRIVER
Output Resistance, Sourcing Current
Output Resistance, Sinking Current
Output Resistance, Unbiased
Transition Times
BST − SW = 12 V
BST − SW = 12 V
BST − SW = 0 V
BST − SW = 12 V, CLOAD = 3 nF, see Figure 4
BST − SW = 12 V, CLOAD = 3 nF, see Figure 4
BST − SW = 12 V, CLOAD = 3 nF, see Figure 4
BST − SW = 12 V, CLOAD = 3 nF, see Figure 4
SW to PGND
2.2
1.0
10
25
20
25
25
10
3.5
2.5
Ω
Ω
kΩ
ns
ns
ns
ns
kΩ
trDRVH
tfDRVH
tpdhDRVH
tpdlDRVH
40
30
40
35
Propagation Delay Times2
SW Pull-Down Resistance
LOW-SIDE DRIVER
Output Resistance, Sourcing Current
Output Resistance, Sinking Current
Output Resistance, Unbiased
Transition Times
2.0
1.0
10
20
16
12
30
190
150
3.2
2.5
Ω
Ω
VCC = PGND
kΩ
ns
ns
ns
ns
ns
ns
trDRVL
tfDRVL
tpdhDRVL
tpdlDRVL
CLOAD = 3 nF, see Figure 4
CLOAD = 3 nF, see Figure 4
CLOAD = 3 nF, see Figure 4
CLOAD = 3 nF, see Figure 4
SW = 5 V
35
30
35
45
Propagation Delay Times2
Timeout Delay
110
95
SW = PGND
SUPPLY
Supply Voltage Range
Supply Current
UVLO Voltage
Hysteresis
VCC
ISYS
4.15
1.5
13.2
5
3.0
V
mA
V
BST = 12 V, IN = 0 V
VCC rising
2
350
mV
1 All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC) methods.
2 For propagation delays, tpdh refers to the specified signal going high, and tpdl refers to it going low.
Rev. 0 | Page 3 of 16
ADP3118
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Rating
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
VCC
BST
BST to SW
SW
DC
<200 ns
DRVH
DC
<200 ns
DRVL
DC
−0.3 V to +15 V
−0.3 V to VCC +15 V
−0.3 V to +15 V
−5 V to +15 V
−10 V to +25 V
Unless otherwise specified, all voltages are referenced to PGND.
SW − 0.3 V to BST + 0.3 V
SW − 2 V to BST + 0.3 V
−0.3 V to VCC + 0.3 V
−2 V to VCC + 0.3 V
−0.3 V to 6.5 V
<200 ns
OD
IN,
θJA, SOIC
2-Layer Board
123°C/W
90°C/W
4-Layer Board
Operating Ambient Temperature
Range
0°C to 85°C
Junction Temperature Range
Storage Temperature Range
Lead Temperature Range
0°C to 150°C
−65°C to +150°C
Soldering (10 sec)
Vapor Phase (60 sec)
Infrared (15 sec)
300°C
215°C
260°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degrada-
tion or loss of functionality.
Rev. 0 | Page 4 of 16
ADP3118
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
BST
IN
1
2
3
4
8
7
6
5
DRVH
SW
ADP3118
OD
PGND
DRVL
TOP VIEW
(Not to Scale)
VCC
Figure 2. 8-Lead SOIC Pin Configuration
Table 3. Pin Function Descriptions
Pin No. Mnemonic Description
1
2
3
BST
Upper MOSFET Floating Bootstrap Supply. A capacitor connected between the BST and SW pins holds this
bootstrapped voltage for the high-side MOSFET as it is switched.
Logic Level PWM Input. This pin has primary control of the driver outputs. In normal operation, pulling this pin
low turns on the low-side driver; pulling it high turns on the high-side driver.
IN
OD
Output Disable. When low, this pin disables normal operation, forcing DRVH and DRVL low.
Input Supply. This pin should be bypassed to PGND with ~1 µF ceramic capacitor.
Synchronous Rectifier Drive. Output drive for the lower (synchronous rectifier) MOSFET.
Power Ground. Should be closely connected to the source of the lower MOSFET.
This pin is connected to the buck-switching node, close to the upper MOSFET’s source. It is the floating return
for the upper MOSFET drive signal. It is also used to monitor the switched voltage to prevent turn-on of the
lower MOSFET until the voltage is below ~1 V.
4
5
6
7
VCC
DRVL
PGND
SW
8
DRVH
Buck Drive. Output drive for the upper (buck) MOSFET.
Rev. 0 | Page 5 of 16
ADP3118
TIMING CHARACTERISTICS
OD
tpdl
OD
tpdh
OD
90%
DRVH
OR
DRVL
10%
Figure 3. Output Disable Timing Diagram
IN
tf
tpdl
DRVL
DRVL
tpdl
DRVH
tr
DRVL
DRVL
tf
DRVH
tpdh
tr
DRVH
DRVH
DRVH-SW
V
V
TH
TH
tpdh
DRVL
SW
1V
Figure 4. Timing Diagram—Timing Is Referenced to the 90% and 10% Points, Unless Otherwise Noted
Rev. 0 | Page 6 of 16
ADP3118
TYPICAL PERFORMANCE CHARACTERISTICS
24
22
20
18
16
14
IN
VCC = 12V
= 3nF
C
LOAD
DRVH
DRVL
DRVH
DRVL
0
25
50
75
100
125
JUNCTION TEMPERATURE (°C)
Figure 5. DRVH Rise and DRVL Fall Times
LOAD = 6 nF for DRVL, CLOAD = 2 nF for DRVH
Figure 8. DRVH and DRVL Fall Times vs. Temperature
C
40
35
30
25
20
15
10
5
T
= 25°C
A
VCC = 12V
DRVH
IN
DRVL
DRVL
DRVH
2.0
2.5
3.0
3.5
4.0
4.5
5.0
LOAD CAPACITANCE (nF)
Figure 9. DRVH and DRVL Rise Times vs. Load Capacitance
Figure 6. DRVH Fall and DRVL Rise Times
CLOAD = 6 nF for DRVL, CLOAD = 2 nF for DRVH
35
35
30
25
20
15
VCC = 12V
VCC = 12V
LOAD
T
= 25°C
A
C
= 3nF
30
25
20
15
10
5
DRVH
DRVH
DRVL
DRVL
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
25
50
75
100
125
LOAD CAPACITANCE (nF)
JUNCTION TEMPERATURE (°C)
Figure 10. DRVH and DRVL Fall Times vs. Load Capacitance
Figure 7. DRVH and DRVL Rise Times vs. Temperature
Rev. 0 | Page 7 of 16
ADP3118
60
12
11
10
9
T = 25°C
A
T
= 25°C
A
C
= 3nF
VCC = 12V
= 3nF
LOAD
C
LOAD
45
30
15
0
8
7
6
5
4
3
2
1
0
0
200
400
600
800
1000
1200
1400
0
1
2
3
4
5
6
7
8
9
10 11 12
FREQUENCY (kHz)
VCC VOLTAGE (V)
Figure 11. Supply Current vs. Frequency
Figure 13. DRVL Output Voltage vs. Supply Voltage
13
12
11
10
9
VCC = 12V
= 3nF
C
LOAD
= 250kHz
f
IN
0
25
50
75
100
125
JUNCTION TEMPERATURE (°C)
Figure 12. Supply Current vs. Temperature
Rev. 0 | Page 8 of 16
ADP3118
THEORY OF OPERATION
To complete the cycle, Q1 is switched off by pulling the gate
The ADP3118 is a dual-MOSFET driver optimized for driving
two N-channel MOSFETs in a synchronous buck converter
topology. A single PWM input signal is all that is required to
properly drive the high-side and the low-side MOSFETs. Each
driver is capable of driving a 3 nF load at speeds up to 500 kHz.
down to the voltage at the SW pin. When the low-side
MOSFET, Q2, turns on, the SW pin is pulled to ground. This
allows the bootstrap capacitor to charge up to VCC again.
The high-side driver’s output is in phase with the PWM input.
When the driver is disabled, the high-side gate is held low.
A more detailed description of the ADP3118 and its features
follows. See Figure 1.
OVERLAP PROTECTION CIRCUIT
The overlap protection circuit prevents both of the main power
switches, Q1 and Q2, from being on at the same time. This is
done to prevent shoot-through currents from flowing through
both power switches and the associated losses that can occur
during their on/off transitions. The overlap protection circuit
accomplishes this by adaptively controlling the delay from the
Q1 turn off to the Q2 turn on, and by internally setting the
delay from the Q2 turn off to the Q1 turn on.
LOW-SIDE DRIVER
The low-side driver is designed to drive a ground-referenced
N-channel MOSFET. The bias to the low-side driver is
internally connected to the VCC supply and PGND.
When the driver is enabled, the driver’s output is 180° out of
phase with the PWM input. When the ADP3118 is disabled,
the low-side gate is held low.
HIGH-SIDE DRIVER
To prevent the overlap of the gate drives during the Q1 turn off
and the Q2 turn on, the overlap circuit monitors the voltage at
the SW pin. When the PWM input signal goes low, Q1 begins
to turn off (after propagation delay). Before Q2 can turn on, the
overlap protection circuit makes sure that SW has first gone
high and then waits for the voltage at the SW pin to fall from
VIN to 1 V. Once the voltage on the SW pin falls to 1 V, Q2
begins turn on. If the SW pin has not gone high first, the Q2
turn on is delayed by a fixed 150 ns. By waiting for the voltage
on the SW pin to reach 1 V or for the fixed delay time, the
overlap protection circuit ensures that Q1 is off before Q2 turns
on, regardless of variations in temperature, supply voltage, input
pulse width, gate charge, and drive current. If SW does not go
below 1 V after 190 ns, DRVL turns on. This can occur if the
current flowing in the output inductor is negative and is flowing
through the high-side MOSFET body diode.
The high-side driver is designed to drive a floating N-channel
MOSFET. The bias voltage for the high-side driver is developed
by an external bootstrap supply circuit, which is connected
between the BST and SW pins.
The bootstrap circuit comprises a diode, D1, and bootstrap
capacitor, CBST1. CBST2 and RBST are included to reduce the high-
side gate drive voltage and to limit the switch node slew rate
(referred to as a Boot-Snap circuit, see the Application
Information section for more details). When the ADP3118 is
starting up, the SW pin is at ground, so the bootstrap capacitor
charges up to VCC through D1. When the PWM input goes
high, the high-side driver begins to turn on the high-side
MOSFET, Q1, by pulling charge out of CBST1 and CBST2. As Q1
turns on, the SW pin rises up to VIN, forcing the BST pin to VIN
+ VC (BST), which is enough gate-to-source voltage to hold Q1 on.
Rev. 0 | Page 9 of 16
ADP3118
APPLICATION INFORMATION
A small-signal diode can be used for the bootstrap diode due
to the ample gate drive voltage supplied by VCC. The bootstrap
diode must have a minimum 15 V rating to withstand the
maximum supply voltage. The average forward current can
be estimated by
SUPPLY CAPACITOR SELECTION
For the supply input (VCC) of the ADP3118, a local bypass
capacitor is recommended to reduce the noise and to supply
some of the peak currents drawn. Use a 4.7 µF, low ESR
capacitor. Multilayer ceramic chip (MLCC) capacitors provide
the best combination of low ESR and small size. Keep the
ceramic capacitor as close as possible to the ADP3118.
IF(AVG) = QGATE × fMAX
(3)
where fMAX is the maximum switching frequency of the
controller. The peak surge current rating should be calculated
using
BOOTSTRAP CIRCUIT
The bootstrap circuit uses a charge storage capacitor (CBST
and a diode, as shown in Figure 1. These components can be
selected after the high-side MOSFET is chosen. The bootstrap
capacitor must have a voltage rating that can handle twice the
maximum supply voltage. A minimum 50 V rating is
)
VCC −VD
RBST
IF(PEAK)
=
(4)
MOSFET SELECTION
recommended. The capacitor values are determined by:
When interfacing the ADP3118 to external MOSFETs, there are
a few considerations that the designer should be aware of. These
help to make a more robust design that minimizes stresses on
both the driver and the MOSFETs. These stresses include
exceeding the short-time duration voltage ratings on the driver
pins as well as the external MOSFET.
QGATE
C
BST1 +C BST2 = 10×
(1)
(2)
VGATE
VGATE
CBST1
BST1 +CBST2 VCC −VD
=
C
where:
It is also highly recommended to use the Boot-Snap circuit to
improve the interaction of the driver with the characteristics of
the MOSFETs. If a simple bootstrap arrangement is used, make
sure to include a proper snubber network on the SW node.
Q
GATE is the total gate charge of the high-side MOSFET at VGATE.
VGATE is the desired gate drive voltage (usually in the range of 5 V
to 10 V, 7 V being typical).
VD is the voltage drop across D1.
HIGH-SIDE (CONTROL) MOSFETS
Rearranging Equations 1 and 2 to solve for CBST1 yields
The high-side MOSFET is usually selected to be high speed to
minimize switching losses (see the ADP3186 or ADP3188 data
sheet for Flex-Mode controller details). This usually implies a
low gate resistance and low input capacitance/charge device.
Yet, a significant source lead inductance can also exist. This
depends mainly on the MOSFET package; it is best to contact
the MOSFET vendor for this information.
QGATE
VCC −VD
C
BST1= 10×
C
BST2 can then be found by rearranging Equation 1
QGATE
VGATE
C
BST2 = 10×
−CBST1
The ADP3118 DRVH output impedance and the input resistance
of the MOSFETs determine the rate of charge delivery to the
gate’s internal capacitance. This determines the speed at which
the MOSFETs turn on and off. However, due to potentially large
currents flowing in the MOSFETs at the on and off times (this
current is usually larger at turn off due to ramping up of the out-
put current in the output inductor), the source lead inductance
generates a significant voltage when the high-side MOSFETs
switch off. This creates a significant drain-source voltage spike
across the internal die of the MOSFETs and can lead to a
catastrophic avalanche. The mechanisms involved in this
avalanche condition can be referenced in literature from the
MOSFET suppliers.
For example, an NTD60N02 has a total gate charge of about
12 nC at VGATE = 7 V. Using VCC = 12 V and VD = 1 V, one finds
CBST1 = 12 nF and CBST2 = 6.8 nF. Good quality ceramic capacitors
should be used.
RBST is used for slew-rate limiting to minimize the ringing at the
switch node. It also provides peak current limiting through D1.
An RBST value of 1.5 Ω to 2.2 Ω is a good choice. The resistor
needs to be able to handle at least 250 mW due to the peak
currents that flow through it.
Rev. 0 | Page 10 of 16
ADP3118
proper switching time, so the state of the DRVL pin is moni-
The MOSFET vendor should provide a maximum voltage slew
rate at drain current rating such that this can be designed around.
Once you have this specification, determine the maximum
current you expect to see in the MOSFET. This can be done
with the following equation:
tored to go below one sixth of VCC. A delay is then added. Due
to the Miller capacitance and internal delays of the low-side
MOSFET gate, one must ensure that the Miller to input capaci-
tance ratio is low enough and that the low-side MOSFET internal
delays are not so large as to allow accidental turn on of the low-
side when the high-side turns on.
DMAX
IMAX = IDC(per phase) +
(VCC −VOUT
)
×
(5)
f
MAX × LOUT
Contact sales for an updated list of recommended low-side
MOSFETs.
where:
MAX is determined for the VR controller being used with
the driver. This current is divided roughly equally between
MOSFETs if more than one is used (assume a worst-case
mismatch of 30% for design margin).
D
PC BOARD LAYOUT CONSIDERATIONS
Use the following general guidelines when designing printed
circuit boards.
LOUT is the output inductor value.
•
•
•
•
•
Trace out the high current paths and use short, wide
(>20 mil) traces to make these connections.
When producing your design, there is no exact method for
calculating the dV/dt due to the parasitic effects in the external
MOSFETs as well as the PCB. However, it can be measured to
determine if it is safe. If it appears that the dV/dt is too fast, an
optional gate resistor can be added between DRVH and the
high-side MOSFETs. This resistor slows down the dV/dt, but it
increases the switching losses in the high-side MOSFETs. The
ADP3118 has been optimally designed with an internal drive
impedance that works with most MOSFETs to switch them
efficiently yet minimizes dV/dt. However, some high speed
MOSFETs may require this external gate resistor depending on
the currents being switched in the MOSFET.
Minimize trace inductance between DRVH and DRVL
outputs and MOSFET gates.
Connect the PGND pin of the ADP3118 as closely as
possible to the source of the lower MOSFET.
Locate the VCC bypass capacitor as close as possible to the
VCC and PGND pins.
Use vias to other layers when possible to maximize thermal
conduction away from the IC.
The circuit in Figure 15 shows how four drivers can be
combined with the ADP3188 to form a total power conversion
solution for generating VCC (CORE) for an Intel CPU that is VRD
10.x-compliant.
LOW-SIDE (SYNCHRONOUS) MOSFETS
The low-side MOSFETs are usually selected to have a low on
resistance to minimize conduction losses. This usually implies a
large input gate capacitance and gate charge. The first concern is
to make sure the power delivery from the ADP3118’s DRVL
does not exceed the thermal rating of the driver (see the
ADP3186 or ADP3188 data sheet for Flex-Mode controller
details).
Figure 14 shows an example of the typical land patterns based
on the guidelines given previously. For more detailed layout
guidelines for a complete CPU voltage regulator subsystem,
refer to the PC Board Layout Considerations section of the
ADP3188 data sheet.
C
BST1
The next concern for the low-side MOSFETs is based on
preventing them from inadvertently being switched on when
the high-side MOSFET turns on. This occurs due to the drain-
gate (Miller, also specified as Crss) capacitance of the MOSFET.
When the drain of the low-side MOSFET is switched to VCC by
the high-side turning on (at a rate dV/dt), the internal gate of
the low-side MOSFET is pulled up by an amount roughly equal
to VCC × (Crss/Ciss). It is important to make sure this does not put
the MOSFET into conduction.
R
C
BST
BST2
D1
Another consideration is the nonoverlap circuitry of the
ADP3118, which attempts to minimize the nonoverlap period.
During the state of the high-side turning off to low-side turning
on, the SW pin is monitored (as well as the conditions of SW
prior to switching) to adequately prevent overlap.
C
VCC
However, during the low-side turn off to high-side turn on,
the SW pin does not contain information for determining the
Figure 14. External Component Placement Example
Rev. 0 | Page 11 of 16
ADP3118
Figure 15. VRD 10-Compliant Power Supply Circuit
Rev. 0 | Page 12 of 16
ADP3118
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
8
1
5
4
6.20 (0.2440)
5.80 (0.2284)
4.00 (0.1574)
3.80 (0.1497)
1.27 (0.0500)
BSC
0.50 (0.0196)
0.25 (0.0099)
× 45°
1.75 (0.0688)
1.35 (0.0532)
0.25 (0.0098)
0.10 (0.0040)
8°
0.51 (0.0201)
0.31 (0.0122)
0° 1.27 (0.0500)
COPLANARITY
0.10
0.25 (0.0098)
0.17 (0.0067)
SEATING
PLANE
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
Figure 16. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters (inches)
ORDERING GUIDE
Temperature
Range
Package
Option
Quantity
per Reel
Model
Package Description
ADP3118JRZ1
ADP3118JRZ-RL1
0°C to 85°C
0°C to 85°C
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package(SOIC_N)
R-8
R-8
N/A
2500
1 Z = Pb-free part.
Rev. 0 | Page 13 of 16
ADP3118
NOTES
Rev. 0 | Page 14 of 16
ADP3118
NOTES
Rev. 0 | Page 15 of 16
ADP3118
NOTES
©2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05452–0–4/05(0)
Rev. 0 | Page 16 of 16
相关型号:
©2020 ICPDF网 联系我们和版权申明