AD9949AKCPZ [ADI]
12-Bit CCD Signal Processor with Precision Timing Core; 12位CCD信号处理器, Precision Timing内核型号: | AD9949AKCPZ |
厂家: | ADI |
描述: | 12-Bit CCD Signal Processor with Precision Timing Core |
文件: | 总36页 (文件大小:775K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
12-Bit CCD Signal Processor with
Precision Timing Core
AD9949
FEATURES
GENERAL DESCRIPTION
New AD9949A supports CCD line length > 4096 pixels
Correlated double sampler (CDS)
The AD9949 is a highly integrated CCD signal processor for
digital still camera applications. Specified at pixel rates of up to
36 MHz, the AD9949 consists of a complete analog front end
with A/D conversion, combined with a programmable timing
driver. The Precision Timing core allows adjustment of high
speed clocks with < 600 ps resolution.
0 dB to 18 dB pixel gain amplifier (PxGA®)
6 dB to 42 dB 10-bit variable gain amplifier (VGA)
12-bit, 36 MSPS analog-to-digital converter (ADC)
Black level clamp with variable level control
Complete on-chip timing driver
The analog front end includes black level clamping, CDS,
PxGA, VGA, and a 36 MSPS, 12-bit ADC. The timing driver
provides the high speed CCD clock drivers for RG and H1 to
H4. Operation is programmed using a 3-wire serial interface.
Precision Timing™ core with < 600 ps resolution
On-chip 3 V horizontal and RG drivers
40-lead LFCSP package
APPLICATIONS
Digital still cameras
High speed digital imaging applications
Packaged in a space-saving, 40-lead LFCSP package, the
AD9949 is specified over an operating temperature range of
−20°C to +85°C.
FUNCTIONAL BLOCK DIAGRAM
REFT REFB
V
REF
0dB TO 18dB
6dB TO 42dB
VGA
12
12-BIT
ADC
DOUT
CDS
PxGA
CCDIN
CLAMP
INTERNAL
CLOCKS
HBLK
CLP/PBLK
CLI
RG
PRECISION
TIMING
CORE
HORIZONTAL
DRIVERS
4
H1 TO H4
SYNC
INTERNAL
GENERATOR
REGISTERS
AD9949
HD
VD
SL
SCK SDATA
Figure 1.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
AD9949
TABLE OF CONTENTS
Specifications..................................................................................... 3
Individual HBLK Sequences..................................................... 21
Generating Special HBLK Patterns.............................................. 23
Horizontal Sequence Control................................................... 23
External HBLK Signal................................................................ 23
H-Counter Synchronization ..................................................... 24
Power-Up Procedure...................................................................... 25
Recommended Power-Up Sequence ....................................... 25
Analog Front End Description and Operation .......................... 26
DC Restore .................................................................................. 26
Correlated Double Sampler ...................................................... 26
PxGA............................................................................................ 26
Variable Gain Amplifier ............................................................ 29
ADC ............................................................................................. 29
Optical Black Clamp.................................................................. 29
Digital Data Outputs.................................................................. 29
Applications Information.............................................................. 30
Circuit Configuration................................................................ 30
Grounding and Decoupling Recommendations.................... 30
Driving the CLI Input................................................................ 31
Horizontal Timing Sequence Example.................................... 31
Outline Dimensions....................................................................... 34
Ordering Guide .......................................................................... 34
General Specifications ................................................................. 3
Digital Specifications ................................................................... 3
Analog Specifications................................................................... 4
Timing Specifications .................................................................. 5
Absolute Maximum Ratings............................................................ 6
Thermal Characteristics .............................................................. 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Terminology ...................................................................................... 8
Equivalent Input/Output Circuits .................................................. 9
Typical Performance Characteristics ........................................... 10
System Overview ............................................................................ 11
H-Counter Behavior .................................................................. 11
Serial Interface Timing .................................................................. 12
Complete Register Listing ............................................................. 13
Precision Timing High Speed Timing Generation...................... 18
Timing Resolution...................................................................... 18
High Speed Clock Programmability........................................ 18
H-Driver and RG Outputs ........................................................ 19
Digital Data Outputs.................................................................. 19
Horizontal Clamping and Blanking............................................. 21
Individual CLPOB and PBLK Sequences................................ 21
REVISION HISTORY
11/04—Data Sheet Changed from Rev. A to Rev. B
Changes to Ordering Guide .......................................................... 35
9/04—Data Sheet Changed from Rev. 0 to Rev. A
Changes to Table 12 ....................................................................... 17
Changes to Table 15 ....................................................................... 17
Changes to H-Counter Sync Section ........................................... 24
Changes to Recommended Power-Up Sequence Section......... 25
Changes to Ordering Guide.......................................................... 35
Changes to Features.......................................................................... 1
Changes to Analog Specifications .................................................. 4
Changes to Terminology Section.................................................... 9
Added H-Counter Behavior Section............................................ 12
Changes to Table 7.......................................................................... 14
5/03—Revision 0: Initial Version
Rev. B | Page 2 of 36
AD9949
SPECIFICATIONS
GENERAL SPECIFICATIONS
Table 1.
Parameter
Min
Typ
Max
Unit
TEMPERATURE RANGE
Operating
Storage
−20
−65
36
+85
+150
°C
°C
MAXIMUM CLOCK RATE
POWER SUPPLY VOLTAGE
AVDD, TCVDD (AFE, Timing Core)
HVDD (H1 to H4 Drivers)
RGVDD (RG Driver)
DRVDD (D0 to D11 Drivers)
DVDD (All Other Digital)
POWER DISSIPATION
MHz
2.7
2.7
2.7
2.7
2.7
3.0
3.0
3.0
3.0
3.0
3.6
3.6
3.6
3.6
3.6
V
V
V
V
V
36 MHz, HVDD = RGVDD = 3 V, 100 pF H1 to H4 Loading1
Total Shutdown Mode
320
1
mW
mW
1 The total power dissipated by the HVDD supply may be approximated using the equation
Total HVDD Power = (CLOAD x HVDD x Pixel Frequency) x HVDD x (Number of H – Outputs Used)
Reducing the H-loading, using only two of the outputs, and/or using a lower HVDD supply, reduces the power dissipation.
DIGITAL SPECIFICATIONS
TMIN to TMAX, AVDD = DVDD = DRVDD = HVDD = RGVDD = 2.7 V, CL = 20 pF, unless otherwise noted.
Table 2.
Parameter
Symbol
Min
Typ
Max
Unit
LOGIC INPUTS
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Capacitance
VIH
VIL
IIH
IIL
CIN
2.1
V
V
µA
µA
pF
0.6
10
10
10
LOGIC OUTPUTS
High Level Output Voltage, IOH = 2 mA
Low Level Output Voltage, IOL = 2 mA
CLI INPUT
VOH
VOL
2.2
V
V
0.5
High Level Input Voltage
(TCVDD/2 + 0.5 V)
VIH–CLI
VIL–CLI
1.85
V
V
Low Level Input Voltage
RG AND H-DRIVER OUTPUTS
High Level Output Voltage
(RGVDD – 0.5 V and HVDD – 0.5 V)
Low Level Output Voltage
Maximum Output Current (Programmable)
Maximum Load Capacitance
0.85
0.5
VOH
VOL
2.2
V
V
mA
pF
30
100
Rev. B | Page 3 of 36
AD9949
ANALOG SPECIFICATIONS
TMIN to TMAX, AVDD = DVDD = 3.0 V, fCLI = 36 MHz, typical timing specifications, unless otherwise noted.
Table 3.
Parameter
Min
Typ
Max
Unit
Notes
CDS
Gain
0
dB
Allowable CCD Reset Transient1
Maximum Input Range before Saturation1
Maximum CCD Black Pixel Amplitude1
PIXEL GAIN AMPLIFIER (P×GA)
Gain Control Resolution
Gain Monotonicity
500
mV
V p-p
mV
1.0
50
256
Steps
Minimum Gain
Maximum Gain
0
18
dB
dB
VARIABLE GAIN AMPLIFIER (VGA)
Maximum Input Range
Maximum Output Range
Gain Control Resolution
Gain Monotonicity
1.0
2.0
V p-p
V p-p
Steps
1024
Guaranteed
Gain Range
Minimum Gain (VGA Code 0)
Maximum Gain (VGA Code 1023)
BLACK LEVEL CLAMP
6
42
dB
dB
Clamp Level Resolution
Clamp Level
256
Steps
Measured at ADC output
Minimum Clamp Level (0)
Maximum Clamp Level (255)
A/D CONVERTER
0
255
LSB
LSB
Resolution
Differential Nonlinearity (DNL)
No Missing Codes
Integral Nonlinearity (INL)
Full-Scale Input Voltage
VOLTAGE REFERENCE
Reference Top Voltage (REFT)
Reference Bottom Voltage (REFB)
SYSTEM PERFORMANCE
VGA Gain Accuracy
12
−1.0
Bits
LSB
0.5
+1.0
8
Guaranteed
LSB
V
2.0
2.0
1.0
V
V
Specifications include entire signal chain
Minimum Gain (Code 0)
Maximum Gain (Code 1023)
Peak Nonlinearity, 500 mV Input Signal
Total Output Noise
5.0
40.5
5.5
6.0
42.5
0.6
dB
dB
%
LSB rms
dB
41.5
0.15
0.8
12 dB gain applied
AC grounded input, 6 dB gain applied
Measured with step change on supply
Power Supply Rejection (PSR)
50
1 Input signal characteristics defined as follows:
500mV TYP
RESET TRANSIENT
50mV MAX
1V MAX
OPTICAL BLACK PIXEL
INPUT SIGNAL RANGE
Rev. B | Page 4 of 36
AD9949
TIMING SPECIFICATIONS
CL = 20 pF, fCLI = 36 MHz, unless otherwise noted.
Table 4.
Parameter
Symbol
Min
Typ
Max
Unit
MASTER CLOCK (CLI) (See Figure 16)
CLI Clock Period
CLI High/Low Pulse Width
Delay from CLI to Internal Pixel Period Position
CLPOB PULSE WIDTH (PROGRAMMABLE)1
SAMPLE CLOCKS (See Figure 18)
SHP Rising Edge to SHD Rising Edge
DATA OUTPUTS (See Figure 19 and Figure 20)
Output Delay From Programmed Edge
Pipeline Delay
tCLI
27.8
11.2
ns
ns
ns
tADC
tCLIDLY
tCOB
13.9
6
16.6
2
20
Pixels
tS1
12.5
13.9
ns
tOD
6
11
ns
Cycles
SERIAL INTERFACE (SERIAL TIMING SHOWN IN Figure 14 and Figure 15)
Maximum SCK Frequency
SL to SCK Setup Time
fSCLK
tLS
tLH
tDS
tDH
tDV
10
10
10
10
10
10
MHz
ns
ns
ns
ns
SCK to SL Hold Time
SDATA Valid to SCK Rising Edge Setup
SCK Falling Edge to SDATA Valid Hold
SCK Falling Edge to SDATA Valid Read
ns
1 Minimum CLPOB pulse width is for functional operation only. Wider typical pulses are recommended to achieve low noise clamp reference.
Rev. B | Page 5 of 36
AD9949
ABSOLUTE MAXIMUM RATINGS
Table 5.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute maxi-
mum rating conditions for extended periods may affect device
reliability.
With
Respect to
Parameter
Rating
AVDD and TCVDD
HVDD and RGVDD
AVSS
HVSS,
RGVSS
DVSS,
−0.3 V to +3.9 V
−0.3 V to +3.9 V
DVDD and DRVDD
−0.3 V to +3.9 V
DRVSS
Any VSS
Digital Outputs
CLPOB/PBLK and HBLK DVSS
SCK, SL, and SDATA
RG
Any VSS
DRVSS
−0.3 V to +0.3 V
THERMAL CHARACTERISTICS
−0.3 V to DRVDD + 0.3 V
−0.3 V to DVDD + 0.3 V
−0.3 V to DVDD + 0.3 V
−0.3 V to RGVDD + 0.3 V
−0.3 V to HVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
150°C
Thermal Resistance
40-Lead LFCSP Package: θJA = 27°C/W1.
DVSS
RGVSS
HVSS
AVSS
H1 to H4
REFT, REFB, and CCDIN
Junction Temperature
Lead Temperature (10 s)
1 θJA is measured using a 4-layer PCB with the exposed paddle soldered to the
board.
300°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate
on the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy elec-
trostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation
or loss of functionality.
Rev. B | Page 6 of 36
AD9949
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
D1
D2
D3
1
30 REFB
PIN 1
REFT
AVSS
2
3
4
5
6
7
8
9
29
28
INDICATOR
D4
27 CCDIN
26
DRVSS
DRVDD
D5
AVDD
AD9949
25 CLI
TOP VIEW
24 TCVDD
23
D6
D7
D8 10
TCVSS
22 RGVDD
21 RG
Figure 2. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
1 to 4
5
Mnemonic
D1 to D4
DRVSS
DRVDD
D5 to D11
H1
Type1
DO
P
Description
Data Outputs
Digital Driver Ground
Digital Driver Supply
6
P
7 to 13
14
DO
DO
DO
P
Data Outputs (D11 is MSB)
CCD Horizontal Clock 1
CCD Horizontal Clock 2
H1 to H4 Driver Ground
H1 to H4 Driver Supply
CCD Horizontal Clock 3
CCD Horizontal Clock 4
RG Driver Ground
CCD Reset Gate Clock
RG Driver Supply
Analog Ground for Timing Core
Analog Supply for Timing Core
Master Clock Input
15
H2
16
17
18
HVSS
HVDD
H3
P
DO
DO
P
DO
P
P
P
DI
P
AI
19
H4
20
21
RGVSS
RG
22
23
24
25
RGVDD
TCVSS
TCVDD
CLI
26
27
28
29
AVDD
CCDIN
AVSS
REFT
Analog Supply for AFE
Analog Input for CCD Signal (Connect through Series 0.1 µF Capacitor)
Analog Ground for AFE
Reference Top Decoupling (Decouple with 1.0 µF to AVSS)
Reference Bottom Decoupling (Decouple with 1.0 µF to AVSS)
3-Wire Serial Load
3-Wire Serial Data Input
3-Wire Serial Clock
Vertical Sync Pulse
Horizontal Sync Pulse
Digital Ground
Digital Supply
Optional HBLK Input
P
AO
AO
DI
DI
DI
DI
DI
P
30
31
REFB
SL
32
SDI
33
SCK
34
VD
35
HD
36
37
38
39
DVSS
DVDD
HBLK
CLP/PBLK
D0
P
DI
DO
DO
CLPOB or PBLK Output
Data Output LSB
40
1 Type: AI = Analog Input, AO = Analog Output, DI = Digital Input, DO = Digital Output, P = Power.
Rev. B | Page 7 of 36
AD9949
TERMINOLOGY
Differential Nonlinearity (DNL)
Total Output Noise
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Thus, every
code must have a finite width. No missing codes guaranteed to
12-bit resolution indicates that all 4096 codes, respectively, must
be present over all operating conditions.
The rms output noise is measured using histogram techniques.
The standard deviation of the ADC output codes is calculated
in LSB and represents the rms noise level of the total signal
chain at the specified gain setting. The output noise can be con-
verted to an equivalent voltage, using the relationship
Integral Nonlinearity (INL)
1 LSB = (ADC full scale/2n codes)
INL is the deviation of each individual code measured from a
true straight line from zero to full scale. The point used as zero
scale occurs 0.5 LSB before the first code transition. Positive full
scale is defined as a level 1 LSB and 0.5 LSB beyond the last
code transition. The deviation is measured from the middle of
each particular output code to the true straight line.
where n is the bit resolution of the ADC. For the AD9949,
1 LSB is approximately 0.488 mV.
Power Supply Rejection (PSR)
The PSR is measured with a step change applied to the supply
pins. The PSR specification is calculated from the change in the
data outputs for a given step change in the supply voltage.
Peak Nonlinearity
Peak nonlinearity, a full signal chain specification, refers to the
peak deviation of the output of the AD9949 from a straight line.
The point used as zero scale occurs 0.5 LSB before the first code
transition. Positive full scale is defined as a level 1 LSB and
0.5 LSB beyond the last code transition. The deviation is
measured from the middle of each particular output code to the
straight line reference. The error is then expressed as a
percentage of the 2 V ADC full-scale signal. The input signal is
appropriately gained up to fill the ADC’s full-scale range.
Rev. B | Page 8 of 36
AD9949
EQUIVALENT INPUT/OUTPUT CIRCUITS
AVDD
DVDD
R
330Ω
AVSS
AVSS
DVSS
Figure 3. CCDIN (Pin 27)
Figure 6. Digital Inputs (Pins 31 to 35, 38)
AVDD
HVDD OR RGVDD
330Ω
25kΩ
CLI
DATA
+
1.4V
ENABLE
DOUT
AVSS
Figure 4. CLI (Pin 25)
DVSS
DRVDD
HVSS OR RGVSS
DATA
Figure 7. H1 to H4 and RG (Pins 14 to 15, 18 to 19, 21)
THREE-STATE
DOUT
DVSS
DRVSS
Figure 5. Data Outputs D0 to D11 (Pins 1 to 4, 7 to 13, 40)
Rev. B | Page 9 of 36
AD9949
TYPICAL PERFORMANCE CHARACTERISTICS
1.0
400
350
300
250
200
150
0.5
0
V
= 3.3V
DD
V
= 3.0V
DD
V
= 2.7V
DD
–0.5
–1.0
0
500
1000 1500 2000 2500 3000 3500 4000
ADC OUTPUT CODE
18
24
30
36
SAMPLE RATE (MHz)
Figure 10. Power Curves
Figure 8. Typical DNL
48
40
32
24
16
8
0
0
200
400
600
800
1000
VGA GAIN CODE (LSB)
Figure 9. Output Noise vs. VGA Gain
Rev. B | Page 10 of 36
AD9949
SYSTEM OVERVIEW
H-COUNTER BEHAVIOR
V-DRIVER
V1 TO Vx, VSG1 TO VSGx, SUBCK
When the maximum horizontal count of 4096 pixels is
exceeded, the H-counter in the AD9949 rolls over to zero and
continues counting. It is, therefore, recommended that the
maximum counter value not be exceeded.
H1 TO H4, RG
CCDIN
DOUT
DIGITAL IMAGE
PROCESSING
ASIC
CCD
AD9949
INTEGRATED
AFE + TD
However, the newer AD9949A version behaves differently. In
the AD9949A, the internal H-counter holds at its maximum
count of 4095 instead of rolling over. This feature allows the
AD9949A to be used in applications containing a line length
greater than 4096 pixels. Although no programmable values for
the horizontal blanking or clamping are available beyond pixel
4095, the H, RG, and AFE clocking continues to operate,
sampling the remaining pixels on the line.
HD, VD
CLI
SERIAL
INTERFACE
Figure 11. Typical Application
Figure 11 shows the typical system application diagram for the
AD9949. The CCD output is processed by the AD9949’s AFE
circuitry, which consists of a CDS, a PxGA, a VGA, a black level
clamp, and an ADC. The digitized pixel information is sent to
the digital image processor chip where all postprocessing and
compression occurs. To operate the CCD, CCD timing
parameters are programmed into the AD9949 from the image
processor through the 3-wire serial interface. From the system
master clock, CLI, provided by the image processor, the
AD9949 generates the high speed CCD clocks and all internal
AFE clocks. All AD9949 clocks are synchronized with VD and
HD. The AD9949’s horizontal pulses (CLPOB, PBLK, and
HBLK) are programmed and generated internally.
MAXIMUM FIELD DIMENSIONS
12-BIT HORIZONTAL = 4096 PIXELS MAX
12-BIT VERTICAL = 4096 LINES MAX
The H-drivers for H1 to H4 and RG are included in the
AD9949, allowing these clocks to be directly connected to the
CCD. The H-drive voltage of 3 V is supported in the AD9949.
Figure 12. Vertical and Horizontal Counters
Figure 12 shows the horizontal and vertical counter dimensions
for the AD9949. All internal horizontal clocking is programmed
using these dimensions to specify line and pixel locations.
MAX VD LENGTH IS 4095 LINES
VD
MAX HD LENGTH IS 4095 PIXELS
HD
CLI
Figure 13. Maximum VD/HD Dimensions
Rev. B | Page 11 of 36
AD9949
SERIAL INTERFACE TIMING
The AD9949’s internal registers are accessed through a 3-wire
serial interface. Each register consists of an 8-bit address and a
24-bit data-word. Both the 8-bit address and 24-bit data-word
are written starting with the LSB. To write to each register, a
32-bit operation is required, as shown in Figure 14. Although
many registers are less than 24 bits wide, all 24 bits must be
written for each register. If the register is only 16 bits wide, then
the upper eight bits may be filled with zeros during the serial
write operation. If fewer than 24 bits are written, the register
will not be updated with new data.
Figure 15 shows a more efficient way to write to the registers by
using the AD9949’s address auto-increment capability. Using
this method, the lowest desired address is written first, followed
by multiple 24-bit data-words. Each new 24-bit data-word is
written automatically to the next highest register address. By
eliminating the need to write each 8-bit address, faster register
loading is achieved. Address auto-increment may be used start-
ing with any register location and may be used to write to as few
as two registers or as many as the entire register space.
8-BIT ADDRESS
24-BIT DATA
...
SDATA
SCK
SL
A0
A1
A2
A4
A5
A6
tDH
A7
D1
D2
D3
D21 D22 D23
A3
D0
tDS
...
1
2
3
4
5
6
7
8
9
10
11
12
30
31
32
tLS
tLH
...
...
SL UPDATED
VD/HD UPDATED
VD
HD
...
NOTES
1. INDIVIDUAL SDATA BITS ARE LATCHED ON SCK RISING EDGES.
2. ALL 32 BITS MUST BE WRITTEN: 8 BITS FOR ADDRESS AND 24 BITS FOR DATA.
3. IF THE REGISTER LENGTH IS <24 BITS, THEN DON’T CARE BITS MUST BE USED TO COMPLETE THE 24-BIT DATA LENGTH.
4. NEW DATA IS UPDATED AT EITHER THE SL RISING EDGE OR AT THE HD FALLING EDGE AFTER THE NEXT VD FALLING EDGE.
5. VD/HD UPDATE POSITION MAY BE DELAYED TO ANY HD FALLING EDGE IN THE FIELD USING THE UPDATE REGISTER.
Figure 14. Serial Write Operation
DATA FOR STARTING
REGISTER ADDRESS
DATA FOR NEXT
REGISTER ADDRESS
...
...
...
SDATA
A0
A1
A2
A4
A5
A6
A7
D0
D1
D22 D23
D0
D1
D22 D23 D0
A3
D1
D2
SCK
SL
...
...
...
59 ...
...
58
33
34
55
56
57
1
2
3
4
5
6
7
8
9
10
31
32
...
NOTES
1. MULTIPLE SEQUENTIAL REGISTERS MAY BE LOADED CONTINUOUSLY.
2. THE FIRST (LOWEST ADDRESS) REGISTER ADDRESS IS WRITTEN, FOLLOWED BY MULTIPLE 24-BIT DATA-WORDS.
3. THE ADDRESS WILL AUTOMATICALLY INCREMENT WITH EACH 24-BIT DATA-WORD (ALL 24 BITS MUST BE WRITTEN).
4. SL IS HELD LOW UNTIL THE LAST DESIRED REGISTER HAS BEEN LOADED.
5. NEW DATA IS UPDATED AT EITHER THE SL RISING EDGE OR AT THE HD FALLING EDGE AFTER THE NEXT VD FALLING EDGE.
Figure 15. Continuous Serial Write Operation
Rev. B | Page 12 of 36
AD9949
COMPLETE REGISTER LISTING
Table 7. SL Updated Registers
1. All addresses and default values are expressed in
hexadecimal.
Register
Description
OPRMODE
CTLMODE
SW_RESET
TGCORE _RSTB
AFE Operation Modes
AFE Control Modes
Software Reset Bit
2. All registers are VD/HD updated as shown in Figure 14,
except for the registers indicated in Table 7, which are SL
updated.
Reset Bar Signal for Internal TG Core
PREVENTUPDATE Prevents Update of Registers
VDHDEDGE
FIELDVAL
HBLKRETIME
CLPBLKOUT
CLPBLKEN
H1CONTROL
RGCONTROL
DRVCONTROL
SAMPCONTROL
DOUTPHASE
VD/HD Active Edge
Resets Internal Field Pulse
Retimes the HBLK to Internal Clock
CLP/BLK Output Pin Select
Enables CLP/BLK Output Pin
H1/H2 Polarity/Edge Control
RG Polarity/Edge Control
RG and H1 to H4 Drive Current
SHP/SHD Sampling Edge Control
Data Output Phase Adjustment
Rev. B | Page 13 of 36
AD9949
Table 8. AFE Register Map
Data Bit
Address
Content
[11:0]
[9:0]
Default Value
Name
Description
00
01
02
03
04
05
4
0
80
4
0
OPRMODE
VGAGAIN
CLAMP LEVEL
CTLMODE
PxGA GAIN01
PxGA GAIN23
AFE Operation Modes. (See Table 14.)
VGA Gain.
Optical Black Clamp Level.
AFE Control Modes. (See Table 15.)
PxGA Gain Registers for Color 0 [8:0] and Color 1 [17:9].
PxGA Gain Registers for Color 2 [8:0] and Color 3 [17:9].
[7:0]
[11:0]
[17:0]
[17:0]
0
Table 9. Miscellaneous Register Map
Data Bit
Content
Address
Default Value
Name
Description
10
[0]
0
SW_RST
Software Reset.
1 = Reset all registers to default, then self-clear back to 0.
11
12
[0]
[0]
0
0
OUT_CONTROL
TGCORE_RSTB
Output Control.
0 = Make all dc outputs inactive.
Timing Core Reset Bar.
0 = Reset TG core.
1 = Resume operation.
13
14
15
[11:0]
[0]
0
0
0
UPDATE
Serial Update.
Sets the line (HD) within the field to update serial data.
Prevents the update of the VD updated registers.
1 = Prevent Update.
VD/HD Active Edge.
PREVENTUPDATE
VDHDEDGE
[0]
0 = Falling Edge Triggered.
1 = Rising Edge Triggered.
16
[1:0]
0
FIELDVAL
Field Value Sync.
0 = Next Field 0.
1 = Next Field 1.
2/3 = Next Field 2.
17
18
[0]
0
0
HBLKRETIME
CLPBLKOUT
Retime HBLK to Internal H1 Clock.
Preferred setting is 1. Setting to 1 adds one cycle delay to HBLK
toggle positions.
CLP/BLK Pin Output Select.
0 = CLPOB.
[1:0]
1 = PBLK.
2 = HBLK.
3 = Low.
19
1A
[0]
[0]
1
0
CLPBLKEN
Enable CLP/BLK Output.
1 = Enable.
Internal Test Mode.
TEST MODE
Should always be set high.
Rev. B | Page 14 of 36
AD9949
Table 10. CLPOB Register Map
Data Bit
Content
Default Value
(Hex)
Address
Name
Description
20
21
22
23
24
[3:0]
F
CLPOBPOL
CLPOBTOG_0
CLPOBTOG_1
CLPOBTOG_2
CLPOBTOG_3
CLPOBSCP0
Start Polarities for CLPOB Sequences 0, 1, 2, and 3.
[23:0]
[23:0]
[23:0]
[23:0]
FFFFFF
FFFFFF
FFFFFF
FFFFFF
0
Sequence 0. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
Sequence 1. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
Sequence 2. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
Sequence 3. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
CLPOB Sequence-Change Position 0 (Hard-Coded to 0).
25
26
27
28
[7:0]
0
CLPOBSPTR
CLPOBSCP1
CLPOBSCP2
CLPOBSCP3
CLPOB Sequence Pointers for Region 0 [1:0], 1 [3:2], 2[5:4], 3[7:6].
CLPOB Sequence-Change Position 1.
CLPOB Sequence-Change Position 2.
[11:0]
[11:0]
[11:0]
FFF
FFF
FFF
CLPOB Sequence-Change Position 3.
Table 11. PBLK Register Map
Data Bit Con-
tent
Default Value
(Hex)
Address
Name
Description
30
31
32
33
34
[3:0]
F
PBLKPOL
Start Polarities for PBLK Sequences 0, 1, 2, and 3.
Sequence 0. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
Sequence 1. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
Sequence 2. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
Sequence 3. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
PBLK Sequence-Change Position 0 (Hard-Coded to 0).
[23:0]
[23:0]
[23:0]
[23:0]
FFFFFF
FFFFFF
FFFFFF
FFFFFF
0
PBLKTOG_0
PBLKTOG_1
PBLKTOG_2
PBLKTOG_3
PBLKSCP0
35
36
37
38
[7:0]
0
PBLKSPTR
PBLKSCP1
PBLKSCP2
PBLKSCP3
PBLK Sequence Pointers for Region 0 [1:0], 1 [3:2], 2 [5:4], 3 [7:6].
PBLK Sequence-Change Position 1.
PBLK Sequence-Change Position 2.
[11:0]
[11:0]
[11:0]
FFF
FFF
FFF
PBLK Sequence-Change Position 3.
Rev. B | Page 15 of 36
AD9949
Table 12. HBLK Register Map
Data Bit
Address Content
Default Value
(Hex)
Name
Description
40
41
42
43
[0]
0
HBLKDIR
HBLK Internal/External.
0 = Internal.
1 = External.
HBLK External Active Polarity.
0 = Active Low.
1 = Active High.
HBLK External Masking Polarity.
0 = Mask H1 Low.
1 = Mask H1High.
HBLK Internal Masking Polarity for Each Sequence 0 to 3.
0 = Mask H1 Low.
[0]
0
1
F
HBLKPOL
[0]
HBLKEXTMASK
HBLKMASK
[3:0]
1 = Mask H1 High.
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
[23:0]
FFFFFF
FFFFFF
FFFFFF
FFFFFF
FFFFFF
FFFFFF
FFFFFF
FFFFFF
FFFFFF
FFFFFF
FFFFFF
HBLKTOG12_0
HBLKTOG34_0
HBLKTOG56_0
HBLKTOG12_1
HBLKTOG34_1
HBLKTOG56_1
HBLKTOG12_2
HBLKTOG34_2
HBLKTOG56_2
HBLKTOG12_3
HBLKTOG34_3
Sequence 0. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
Sequence 0. Toggle Position 3 [11:0] and Toggle Position 4 [23:12].
Sequence 0. Toggle Position 5 [11:0] and Toggle Position 6 [23:12].
Sequence 1. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
Sequence 1. Toggle Position 3 [11:0] and Toggle Position 4 [23:12].
Sequence 1. Toggle Position 5 [11:0] and Toggle Position 6 [23:12].
Sequence 2. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
Sequence 2. Toggle Position 3 [11:0] and Toggle Position 4 [23:12].
Sequence 2. Toggle Position 5 [11:0] and Toggle Position 6 [23:12].
Sequence 3. Toggle Position 1 [11:0] and Toggle Position 2 [23:12].
Sequence 3. Toggle Position 3 [11:0] and Toggle Position 4 [23:12].
FFFFFF
0
HBLKTOG56_3
HBLKSCP0
Sequence 3. Toggle Position 5 [11:0] and Toggle Position 6[23:12].
HBLK Sequence-Change Position 0 (Hard-coded to 0).
50
51
52
53
[7:0]
0
HBLKSPTR
HBLKSCP1
HBLKSCP2
HBLKSCP3
HBLK Sequence Pointers for Region 0 [1:0], 1 [3:2], 2 [5:4], 3 [7:6].
HBLK Sequence-Change Position 1.
HBLK Sequence-Change Position 2.
[11:0]
[11:0]
[11:0]
FFF
FFF
FFF
HBLK Sequence-Change Position 3.
Table 13. H1 to H2, RG, SHP, SHD Register Map
Data Bit
Address Content
Default Value
Name
Description
60
61
62
[12:0]
[12:0]
[14:0]
01001
H1CONTROL
H1 Signal Control. Polarity [0](0 = Inversion, 1 = No Inversion).
H1 Positive Edge Location [6:1].
H1 Negative Edge Location [12:7].
RG Signal Control. Polarity [0](0 = Inversion, 1 = No Inversion).
RG Positive Edge Location [6:1].
RG Negative Edge Location [12:7].
00801
0
RGCONTROL
DRVCONTROL
Drive Strength Control for H1 [2:0], H2 [5:3], H3 [8:6], H4 [11:9], and RG
[14:12].
Drive Current Values: 0 = Off, 1 = 4.3 mA, 2 = 8.6 mA,
3 = 12.9 mA, 4 = 17.2 mA, 5 = 21.5 mA, 6 = 25.8 mA, 7 = 30.1 mA.
63
64
[11:0]
[5:0]
00024
0
SAMPCONTROL SHP/SHD Sample Control. SHP Sampling Location [5:0]. SHD Sampling
Location [11:6].
DOUTPHASE
DOUT Phase Control.
Rev. B | Page 16 of 36
AD9949
Table 14. AFE Operation Register Detail
Data Bit
Content
Default
Value
Address
Name
Description
00
[1:0]
0
PWRDOWN
0 = Normal Operation.
1 = Reference Standby.
2/3 = Total Power-Down
[2]
[3]
[4]
[5]
1
0
0
0
CLPENABLE
CLPSPEED
FASTUPDATE
PBLK_LVL
0 = Disable OB Clamp.
1 = Enable OB Clamp.
0 = Select Normal OB Clamp Settling.
1 = Select Fast OB Clamp Settling.
0 = Ignore VGA Update.
1 = Very Fast Clamping when VGA Is Updated.
DOUT Value during PBLK.
0 = Blank to Zero.
1 = Blank to Clamp Level.
[7:6]
[8]
0
0
TEST MODE
DCBYP
Test Operation Only. Set to zero.
0 = Enable DC restore circuit.
1 = Bypass DC Restore Circuit during PBLK.
[9]
[11:10]
0
0
TESTMODE
CDSGAIN
Test Operation Only. Set to zero.
Adjustment of CDS Gain.
0 = 0 dB.
01 = −2 dB.
10 = −4 dB.
11 = 0 dB.
Table 15. AFE Control Register Detail
Data Bit
Content
Default
Value
Address
Name
Description
03
[1:0]
0
COLORSTEER
0 = Off.
1 = Progressive.
2 = Interlaced.
3 = Three Field.
[2]
[3]
[4]
[5]
1
0
0
0
PxGAENABLE
DOUTDISABLE
DOUTLATCH
GRAYENCODE
0 = Disable PxGA.
1 = Enable PxGA.
0 = Data Outputs Are Driven.
1 = Data Outputs Are Three-Stated.
0 = Latch Data Outputs with DOUT Phase.
1 = Output Latch Transparent.
0 = Binary Encode Data Outputs.
1 = Gray Encode Data Outputs.
Rev. B | Page 17 of 36
AD9949
PRECISION TIMING HIGH SPEED TIMING GENERATION
The AD9949 generates flexible high speed timing signals using
the Precision Timing core. This core is the foundation for gener-
ating the timing used for both the CCD and the AFE: the reset
gate (RG), horizontal drivers (H1 to H4), and the SHP/SHD
sample clocks. A unique architecture makes it routine for the
system designer to optimize image quality by providing precise
control over the horizontal CCD readout and the AFE corre-
lated double sampling.
HIGH SPEED CLOCK PROGRAMMABILITY
Figure 17 shows how the high speed clocks, RG, H1 to H4,
SHP, and SHD, are generated. The RG pulse has programma-
ble rising and falling edges and may be inverted using the
polarity control. The horizontal clocks H1 and H3 have
programmable rising and falling edges and polarity control.
The H2 and H4 clocks are always inverses of H1 and H3, re-
spectively. Table 16 summarizes the high speed timing registers
and their parameters.
TIMING RESOLUTION
The Precision Timing core uses a 1× master clock input (CLI) as
a reference. This clock should be the same as the CCD pixel
clock frequency. Figure 16 illustrates how the internal timing
core divides the master clock period into 48 steps or edge
positions. Therefore, the edge resolution of the Precision Timing
core is (tCLI/48). For more information on using the CLI input,
refer to the Applications Information section.
Each edge location setting is 6 bits wide, but only 48 valid edge
locations are available. Therefore, the register values are
mapped into four quadrants, with each quadrant containing
12 edge locations. Table 17 shows the correct register values for
the corresponding edge locations.
POSITION
CLI
P[0]
P[12]
P[24]
P[36]
P[48] = P[0]
...
tCLIDLY
...
1 PIXEL
PERIOD
NOTES
1. PIXEL CLOCK PERIOD IS DIVIDED INTO 48 POSITIONS, PROVIDING FINE EDGE RESOLUTION FOR HIGH SPEED CLOCKS.
2. THERE IS A FIXED DELAY FROM THE CLI INPUT TO THE INTERNAL PIXEL PERIOD POSITIONS (tCLIDLY = 6 ns TYP).
Figure 16. High Speed Clock Resolution from CLI Master Clock Input
3
CCD SIGNAL
4
1
5
2
RG
6
H1/H3
H2/H4
PROGRAMMABLE CLOCK POSITIONS:
1. RG RISING EDGE.
2. RG FALLING EDGE.
3. SHP SAMPLE LOCATION.
4. SHD SAMPLE LOCATION.
5. H1/H3 RISING EDGE POSITION6. H1/H3 FALLING EDGE POSITION (H2/H4 ARE INVERSE OF H1/H3).
Figure 17. High Speed Clock Programmable Locations
Rev. B | Page 18 of 36
AD9949
Table 16. H1CONTROL, RGCONTROL, DRVCONTROL, and SAMPCONTROL Register Parameters
Parameter
Length
Range
Description
Polarity
1b
6b
6b
6b
3b
6b
High/Low
Polarity Control for H1/H3 and RG (0 = No Inversion, 1 = Inversion).
Positive Edge Location for H1/H3 and RG.
Negative Edge Location for H1/H3 and RG.
Sampling Location for SHP and SHD.
Drive Current for H1 to H4 and RG Outputs, 0 to 7 Steps of 4.1 mA Each.
Phase Location of Data Outputs with Respect to Pixel Period.
Positive Edge
Negative Edge
Sample Location
Drive Control
DOUT Phase
0 to 47 Edge Location
0 to 47 Edge Location
0 to 47 Sample Location
0 to 7 Current Steps
0 to 47 Edge Location
Table 17. Precision Timing Edge Locations
Quadrant
Edge Location (Decimal)
Register Value (Decimal)
0 to 11
16 to 27
32 to 43
48 to 59
Register Value (Binary)
000000 to 001011
010000 to 011011
100000 to 101011
110000 to 111011
I
II
III
IV
0 to 11
12 to 23
24 to 35
36 to 47
H-DRIVER AND RG OUTPUTS
In addition to the programmable timing positions, the AD9949 features on-chip output drivers for the RG and H1 to H4 outputs. These
drivers are powerful enough to directly drive the CCD inputs. The H-driver and RG driver current can be adjusted for optimum rise/fall
time into a particular load by using the DRVCONTROL register (Address 0×62). The DRVCONTROL register is divided into five differ-
ent 3-bit values, each one being adjustable in 4.1 mA increments. The minimum setting of 0 is equal to OFF or three-state, and the maxi-
mum setting of 7 is equal to 30.1 mA.
As shown in Figure 18, the H2/H4 outputs are inverses of H1/H3. The internal propagation delay resulting from the signal inversion is
less than l ns, which is significantly less than the typical rise time driving the CCD load. This results in a H1/H2 crossover voltage at ap-
proximately 50% of the output swing. The crossover voltage is not programmable.
DIGITAL DATA OUTPUTS
The AD9949 data output phase is programmable using the DOUTPHASE register (Address 0×64). Any edge from 0 to 47 may be pro-
grammed, as shown in Figure 19. The pipeline delay for the digital data output is shown in Figure 20.
H1/H3
tRISE
H2/H4
tPD << tRISE
tPD
H1/H3
H2/H4
FIXED CROSSOVER VOLTAGE
Figure 18. H-Clock Inverse Phase Relationship
Rev. B | Page 19 of 36
AD9949
P[0]
P[12]
P[24]
P[36]
P[48] = P[0]
CLI
1 PIXEL PERIOD
tOD
DOUT
NOTES
1. DIGITAL OUTPUT DATA (DOUT) PHASE IS ADJUSTABLE WITH RESPECT TO THE PIXEL PERIOD.
2. WITHIN ONE CLOCK PERIOD, THE DATA TRANSITION CAN BE PROGRAMMED TO ANY OF THE 48 LOCATIONS.
Figure 19. Digital Output Phase Adjustment
CLI
tCLIDLY
N – 1
N
N + 1
N + 2
N + 3
N + 4
N + 5
N + 6
N + 7
N + 8
N + 9
N + 10 N + 11 N + 12 N + 13
CCDIN
SAMPLE PIXEL N
SHD
(INTERNAL)
PIPELINE LATENCY = 11 CYCLES
N – 8 N – 7 N – 6 N – 5 N – 4
N + 1
DOUT
N – 11 N – 10
N – 9
N – 3
N – 2
N – 1
N
N – 13 N – 12
NOTES
1. DEFAULT TIMING VALUES ARE SHOWN: SHDLOC = 0, DOUT PHASE = 0.
2. HIGHER VALUES OF SHD AND/OR DOUTPHASE WILL SHIFT DOUT TRANSITION TO THE RIGHT, WITH RESPECT TO CLI LOCATION.
Figure 20. Pipeline Delay for Digital Data Output
Rev. B | Page 20 of 36
AD9949
HORIZONTAL CLAMPING AND BLANKING
The AD9949’s horizontal clamping and blanking pulses are fully
programmable to suit a variety of applications. Individual
sequences are defined for each signal, which are then organized
into multiple regions during image readout. This allows the
dark pixel clamping and blanking patterns to be changed at
each stage of the readout to accommodate different image
transfer timing and high speed line shifts.
signals are active low and should be programmed accordingly.
Up to four individual sequences can be created for each signal.
INDIVIDUAL HBLK SEQUENCES
The HBLK programmable timing shown in Figure 22 is similar
to CLPOB and PBLK. However, there is no start polarity
control. Only the toggle positions are used to designate the
start and the stop positions of the blanking period. Additionally,
there is a polarity control, HBLKMASK, which designates the
polarity of the horizontal clock signals H1 to H4 during the
blanking period. Setting HBLKMASK high sets H1 = H3 = low
and H2 = H4 = high during the blanking, as shown in Figure 23.
Up to four individual sequences are available for HBLK.
INDIVIDUAL CLPOB AND PBLK SEQUENCES
The AFE horizontal timing consists of CLPOB and PBLK, as
shown in Figure 21. These two signals are independently
programmed using the parameters shown in Table 18. The start
polarity, first toggle position, and second toggle position are
fully programmable for each signal. The CLPOB and PBLK
...
HD
2
3
...
CLPOB
PBLK
1
ACTIVE
ACTIVE
PROGRAMMABLE SETTINGS:
1. START POLARITY (CLAMP AND BLANK REGION ARE ACTIVE LOW).
2. FIRST TOGGLE POSITION.
3. SECOND TOGGLE POSITION.
Figure 21. Clamp and Preblank Pulse Placement
...
...
HD
1
2
BLANK
BLANK
HBLK
PROGRAMMABLE SETTINGS:
1. FIRST TOGGLE POSITION = START OF BLANKING.
2. SECOND TOGGLE POSITION = END OF BLANKING.
Figure 22. Horizontal Blanking (HBLK) Pulse Placement
Table 18. CLPOB and PBLK Individual Sequence Parameters
Parameter
Length
Range
Description
Polarity
Toggle Position 1
Toggle Position 2
1b
12b
12b
High/Low
0 to 4095 Pixel Location
0 to 4095 Pixel Location
Starting Polarity of Clamp and PBLK Pulses for Sequences 0 to 3.
First Toggle Position within the Line for Sequences 0 to 3.
Second Toggle Position within the Line for Sequences 0 to 3.
Table 19. HBLK Individual Sequence Parameters
Parameter
Length
Range
Description
HBLKMASK
1b
High/Low
Masking Polarity for H1 for Sequences 0 to 3 (0 = H1 Low, 1 = H1 High).
First Toggle Position within the Line for Sequences 0 to 3.
Second Toggle Position within the Line for Sequences 0 to 3.
Third Toggle Position within the Line for Sequences 0 to 3.
Fourth Toggle Position within the Line for Sequences 0 to 3.
Fifth Toggle Position within the Line for Sequences 0 to 3.
Sixth Toggle Position within the Line for Sequences 0 to 3.
Toggle Position 1
Toggle Position 2
Toggle Position 3
Toggle Position 4
Toggle Position 5
Toggle Position 6
12b
12b
12b
12b
12b
12b
0 to 4095 Pixel Location
0 to 4095 Pixel Location
0 to 4095 Pixel Location
0 to 4095 Pixel Location
0 to 4095 Pixel Location
0 to 4095 Pixel Location
Rev. B | Page 21 of 36
AD9949
...
...
HD
HBLK
H1/H3
THE POLARITY OF H1 DURING BLANKING IS PROGRAMMABLE (H2 IS OPPOSITE POLARITY OF H1).
...
H1/H3
H2/H4
...
Figure 23. HBLK Masking Control
TOG1
TOG2
TOG3
TOG4
TOG5
TOG6
HBLK
H1/H3
H2/H4
SPECIAL H-BLANK PATTERN IS CREATED USING MULTIPLE HBLK TOGGLE POSITIONS.
Figure 24. Generating Special HBLK Patterns
Table 20. Horizontal Sequence Control Parameters for CLPOB, PBLK, and HBLK
Register
Length
Range
Description
SCP
SPTR
12b
2b
0 to 4095 Line Number
0 to 3 Sequence Number
CLOB/PBLK/HBLK SCP to Define Horizontal Regions 0 to 3.
Sequence Pointer for Horizontal Regions 0 to 3.
Rev. B | Page 22 of 36
AD9949
GENERATING SPECIAL HBLK PATTERNS
Six toggle positions are available for HBLK. Normally, only two
of the toggle positions are used to generate the standard HBLK
interval. However, the additional toggle positions may be used
to generate special HBLK patterns, as shown in Figure 24. The
pattern in this example uses all six toggle positions to generate
two extra groups of pulses during the HBLK interval. By
changing the toggle positions, different patterns can be created.
CLPOB, PBLK, and HBLK each have a separate set of SCPs. For
example, CLPOBSCP1 defines Region 0 for CLPOB, and in that
region any of the four individual CLPOB sequences may be
selected with the CLPOBSPTR register. The next SCP defines a
new region and in that region, each signal can be assigned to a
different individual sequence. The sequence control registers
are summarized in Table 20.
HORIZONTAL SEQUENCE CONTROL
EXTERNAL HBLK SIGNAL
The AD9949 uses sequence change positions (SCP) and
sequence pointers (SPTR) to organize the individual horizontal
sequences. Up to four SCPs are available to divide the readout
into four separate regions, as shown in Figure 25. The SCP0 is
always hard-coded to Line 0, and SCP1 to SCP3 are register
programmable. During each region bounded by the SCP, the
SPTR registers designate which sequence is used by each signal.
The AD9949 can also be used with an external HBLK signal.
Setting the HBLKDIR register (Address 0×40) to high disables
the internal HBLK signal generation. The polarity of the exter-
nal signal is specified using the HBLKPOL register, and the
masking polarity of H1 is specified using the HBLKMASK
register. Table 21 summarizes the register values when using an
external HBLK signal.
SINGLE FIELD (1 VD INTERVAL)
SEQUENCE CHANGE OF POSITION 0
(V-COUNTER = 0)
CLAMP AND PBLK SEQUENCE REGION 0
CLAMP AND PBLK SEQUENCE REGION 1
SEQUENCE CHANGE OF POSITION 1
SEQUENCE CHANGE OF POSITION 2
CLAMP AND PBLK SEQUENCE REGION 2
CLAMP AND PBLK SEQUENCE REGION 3
SEQUENCE CHANGE OF POSITION 3
UP TO FOUR INDIVIDUAL HORIZONTAL CLAMP AND BLANKING REGIONS MAY BE
PROGRAMMED WITHIN A SINGLE FIELD, USING THE SEQUENCE CHANGE POSITIONS.
Figure 25. Clamp and Blanking Sequence Flexibility
Table 21. External HBLK Register Parameters
Register
Length
Range
Description
HBLKDIR
1b
High/Low
Specifies HBLK Internally Generated or Externally Supplied.
1 = External.
HBLKPOL
1b
1b
High/Low
High/Low
External HBLK Active Polarity.
0 = Active Low.
1 = Active High.
External HBLK Masking Polarity.
0 = Mask H1 Low.
HBLKEXTMASK
1 = Mask H1 High.
Rev. B | Page 23 of 36
AD9949
H-COUNTER SYNCHRONIZATION
The H-Counter reset occurs seven CLI cycles following the HD falling edge. The PxGA steering is synchronized with the reset of the
internal H-Counter (see Figure 26).
As mentioned in the H-Counter Behavior section, the AD9949 H-counter rolls over to zero and continues counting when the maximum
counter length is exceeded. The newer AD9949A product does not roll over but holds at its maximum value until the next HD rising edge
occurs.
VD
HD
H-COUNTER
RESET
CLI
H-COUNTER
(PIXEL COUNTER)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
0
0
1
1
2
0
3
1
4
0
5
1
6
0
7
1
8
0
9
1
10 11 12 14 15
0
2
1
3
2
2
3
3
PxGA GAIN
REGISTER
0
1
0
1
0
NOTES
1. INTERNAL H-COUNTER IS RESET 7 CLI CYCLES AFTER THE HD FALLING EDGE (WHEN USING VDHDEDGE = 0).
2. TYPICAL TIMING RELATIONSHIP: CLI RISING EDGE IS COINCIDENT WITH HD FALLING EDGE.
3. PxGA STEERING IS SYNCRONIZED WITH THE RESET OF THE INTERNAL H-COUNTER (MOSAIC SEPARATE MODE IS SHOWN).
Figure 26. H-Counter Synchronization
Rev. B | Page 24 of 36
AD9949
POWER-UP PROCEDURE
RECOMMENDED POWER-UP SEQUENCE
When the AD9949 is powered up, the following sequence is
recommended (refer to Figure 27 for each step):
5. Write a 1 to the PREVENTUPDATE register (Address
0×14). This prevents the updating of the serial register
data.
6. Write to the desired registers to configure high speed
timing and horizontal timing.
7. Write a 1 to the OUT_CONTROL register (Address 0×11).
This allows the outputs to become active after the next
VD/HD rising edge.
8. Write a 0 to the PREVENTUPDATE register (Address
0×14). This allows the serial information to be updated at
next VD/HD falling edge.
1. Turn on the power supplies for the AD9949.
2. Apply the master clock input, CLI, VD, and HD.
3. Although the AD9949 contains an on-chip, power-on reset,
a software reset of the internal registers is recommended.
Write a 1 to the SW_RST register (Address 0×10), which
resets the internal registers to their default values. This bit
is self-clearing and automatically resets back to 0.
4. The Precision Timing core must be reset by writing a 0 to
the TGCORE_RSTB register (Address 0×12) followed by
writing a l to the TGCORE_RSTB register. This starts the
internal timing core operation.
9. The next VD/HD falling edge allows register updates to
occur, including OUT_CONTROL, which enables all clock
outputs.
VDD
1
(INPUT)
CLI
(INPUT)
2
tPWR
3
4
5
6
7
8
SERIAL
WRITES
9
1V
...
...
...
VD
(OUTPUT)
ODD FIELD
EVEN FIELD
1H
2
...
HD
(OUTPUT)
H2/H4
DIGITAL
OUTPUTS
H1/H3, RG
CLOCKS ACTIVE WHEN OUT_CONTROL REGISTER IS
UPDATED AT VD/HD EDGE
Figure 27. Recommended Power-Up Sequence
Rev. B | Page 25 of 36
AD9949
ANALOG FRONT END DESCRIPTION AND OPERATION
Table 22. Adjustable CDS Gain
Operation Register Bits
The AD9949 signal processing chain is shown in Figure 28.
Each processing step is essential in achieving a high quality
image from the raw CCD pixel data.
D11
D10
CDS Gain
0 dB
−2 dB
−4 dB
0 dB
Max CDS Input
1.0 V p-p
1.2 V p-p
1.6 V p-p
1.0 V p-p
0
0
1
1
0
1
0
1
DC RESTORE
To reduce the large dc offset of the CCD output signal, a dc
restore circuit is used with an external 0.1 µF series coupling
capacitor. This restores the dc level of the CCD signal to
approximately 1.5 V to be compatible with the 3 V supply
voltage of the AD9949.
PxGA
The PxGA provides separate gain adjustment for the individual
color pixels. A programmable gain amplifier with four separate
values, the PxGA has the capability to multiplex its gain value
on a pixel-to-pixel basis (see Figure 29). This allows lower
output color pixels to be gained up to match higher output color
pixels. Also, the PxGA may be used to adjust the colors for
white balance, reducing the amount of digital processing that
is needed. The four different gain values are switched according
to the color steering circuitry. Three different color steering
modes for different types of CCD color filter arrays are
CORRELATED DOUBLE SAMPLER
The CDS circuit samples each CCD pixel twice to extract the
video information and reject low frequency noise. The timing
shown in Figure 17 illustrates how the two internally generated
CDS clocks, SHP and SHD, are used to sample the reference
level and the CCD signal level, respectively. The placement of
the SHP and SHD sampling edges is determined by the setting
of the SAMPCONTROL register located at Address 0×63.
Placement of these two clock signals is critical in achieving the
best performance from the CCD.
programmable in the AFE CTLMODE register at Address 0×03
(see Figure 33 to Figure 35 for timing examples). For example,
progressive steering mode accommodates the popular Bayer
arrangement of red, green, and blue filters (see Figure 30).
The gain in the CDS is fixed at 0 dB by default. Using Bits D10
and D11 in the AFE operation register, the gain may be reduced
to −2 dB or −4 dB. This allows the AD9949 to accept an input
signal of greater than 1 V p-p. See Table 14 for register details.
1.0µF 1.0µF
REFB REFT
1.0V 2.0V
DC RESTORE
1.5V
AD9949
INTERNAL
VREF
DOUT
PHASE
SHP
SHD
2V FULL SCALE
0dB ~ 18dB
PxGA
6dB ~ 42dB
1.0µF
OUTPUT
DATA
LATCH
12
CCDIN
12-BIT
ADC
VGA
DOUT
CDS
0dB, –2dB, –4dB
OPTICAL BLACK
CLAMP
DAC
PxGA GAIN
REGISTERS
VGA GAIN
REGISTER
CLPOB PBLK
DIGITAL
FILTER
8
DOUT
SHP SHD PHASE
CLAMP LEVEL
REGISTER
CLPOB PBLK
PRECISION
TIMING
V-H
TIMING
GENERATION
GENERATION
Figure 28. Analog Front End Functional Block Diagram
Rev. B | Page 26 of 36
AD9949
VD
HD
CONTROL
REGISTER
BITS D0 TO D1
A third type of readout uses the Bayer pattern divided into three
different readout fields. The 3-field mode should be used with
this type of CCD (see Figure 32). The color steering performs
the proper multiplexing of the R, G, and B gain values (loaded
into the PxGA gain registers) and is synchronized by the user
with vertical (VD) and horizontal (HD) sync pulses. For timing
information, see Figure 35.
PxGA STEERING
MODE
SELECTION
COLOR
STEERING
CONTROL
3
SHP/SHD
2
GAIN0
GAIN1
GAIN2
GAIN3
4:1
PxGA GAIN
REGISTERS
MUX
8
CCD: 3-FIELD READOUT
FIRST FIELD
COLOR STEERING MODE:
THREE FIELD
CDS
PxGA
VGA
R
Gb
R
Gr
B
R
Gb
R
Gr
B
LINE0
LINE1
LINE2
GAIN0, GAIN1, GAIN0, GAIN1, ...
GAIN2, GAIN3, GAIN2, GAIN3, ...
GAIN0, GAIN1, GAIN0, GAIN1, ...
Figure 29. PxGA Block Diagram
Gr
B
Gr
B
CCD: PROGRESSIVE BAYER
COLOR STEERING MODE:
PROGRESSIVE
Gb
Gb
R
Gb
R
Gr
B
R
Gb
R
Gr
B
LINE0
LINE1
LINE2
GAIN0, GAIN1, GAIN0, GAIN1, ...
GAIN2, GAIN3, GAIN2, GAIN3, ...
GAIN0, GAIN1, GAIN0, GAIN1, ...
SECOND FIELD
Gb
R
B
Gr
B
Gb
R
B
Gr
B
LINE0
LINE1
LINE2
GAIN2, GAIN3, GAIN2, GAIN3, ...
GAIN0, GAIN1, GAIN0, GAIN1, ...
GAIN2, GAIN3, GAIN2, GAIN3, ...
Gr
B
Gr
B
Gb
Gb
Gb
R
Gb
R
Figure 30. CCD Color Filter Example—Progressive Scan
Gr
Gr
The same Bayer pattern can also be interlaced, and the
interlaced mode should be used with this type of CCD (see
Figure 31). The color steering performs the proper multiplexing
of the R, G, and B gain values (loaded into the PxGA gain
registers) and is synchronized by the user with vertical (VD)
and horizontal (HD) sync pulses. For timing information,
see Figure 34.
THIRD FIELD
R
Gb
R
Gr
B
R
Gb
R
Gr
B
LINE0
LINE1
LINE2
GAIN0, GAIN1, GAIN0, GAIN1, ...
GAIN2, GAIN3, GAIN2, GAIN3, ...
GAIN0, GAIN1, GAIN0, GAIN1, ...
Gr
B
Gr
B
Gb
Gb
CCD: INTERLACED BAYER
EVEN FIELD
COLOR STEERING MODE:
INTERLACED
Figure 32. CCD Color Filter Example—Three-Field Readout
R
R
R
R
Gr
Gr
Gr
Gr
R
R
R
R
Gr
Gr
Gr
Gr
LINE0
LINE1
LINE2
GAIN0, GAIN1, GAIN0, GAIN1, ...
GAIN0, GAIN1, GAIN0, GAIN1, ...
GAIN0, GAIN1, GAIN0, GAIN1, ...
ODD FIELD
Gb
Gb
Gb
Gb
B
B
B
B
Gb
Gb
Gb
Gb
B
B
B
B
LINE0
LINE1
LINE2
GAIN2, GAIN3, GAIN2, GAIN3, ...
GAIN2, GAIN3, GAIN2, GAIN3, ...
GAIN2, GAIN3, GAIN2, GAIN3, ...
Figure 31. CCD Color Filter Example—Interlaced Readout
Rev. B | Page 27 of 36
AD9949
FIELDVAL
FIELDVAL = 0
FIELDVAL = 0
VD
HD
PxGA GAIN
REGISTER
X
X
0
1
0
1
2
3
2
3
0
1
0
1
0
1
0
1
2
3
2
3
0
1
0
1
0
NOTES
1. VD FALLING EDGE WILL RESET THE PxGA GAIN REGISTER STEERING TO 0101 LINE.
2. HD FALLING EDGES WILL ALTERNATE THE PxGA GAIN REGISTER STEERING BETWEEN 0101 AND 2323 LINES.
3. FIELDVAL IS ALWAYS RESET TO 0 ON VD FALLING EDGES.
Figure 33. PxGA Color Steering—Progressive Mode
FIELDVAL
VD
FIELDVAL = 0
FIELDVAL = 1
FIELDVAL = 0
HD
PxGA GAIN
REGISTER
X
X
0
1
0
1
0
1
0
1
2
3
2
3
2
3
2
3
0
1
0
1
0
1
0
1
NOTES
1. FIELDVAL = 0 (START OF FIRST FIELD) WILL RESET THE PxGA GAIN REGISTER STEERING TO 0101 LINE.
2. FIELDVAL = 1 (START OF SECOND FIELD) WILL RESET THE PxGA GAIN REGISTER STEERING TO 2323 LINE.
3. HD FALLING EDGES WILL RESET THE PxGA GAIN REGISTER STEERING TO EITHER 0 (FIELDVAL = 0) OR 2 (FIELDVAL = 1).
4. FIELDVAL WILL TOGGLE BETWEEN 0 AND 1 ON EACH VD FALLING EDGE.
Figure 34. PxGA Color Steering—Interlaced Mode
FIELDVAL
VD
FIELDVAL = 0
FIELDVAL = 1
FIELDVAL = 2
HD
PxGA GAIN
REGISTER
X
X
0
1
0
1
2
3
2
3
2
3
2
3
1
0
1
0
0
1
0
1
2
3
2
3
NOTES
1. FIELDVAL = 0 (START OF FIRST FIELD) WILL RESET THE PxGA GAIN REGISTER STEERING TO 0101 LINE.
2. FIELDVAL = 1 (START OF SECOND FIELD) WILL RESET THE PxGA GAIN REGISTER STEERING TO 2323 LINE.
3. FIELDVAL = 2 (START OF THIRD FIELD) WILL RESET THE PxGA GAIN REGISTER STEERING TO 0101 LINE.
4. HD FALLING EDGES WILL ALTERNATE THE PxGA GAIN REGISTER STEERING BETWEEN 0101 AND 2323 LINES.
5. FIELDVAL WILL INCREMENT AT EACH VD FALLING EDGE, REPEATING THE 0...1...2...0...1...2 PATTERN.
Figure 35. PxGA Color Steering—Three-Field Mode
Rev. B | Page 28 of 36
AD9949
42
36
30
24
18
12
0
The PxGA gain for each of the four channels is variable from
0 dB to 18 dB in 512 steps, specified using the PxGA GAIN01
and PxGA GAIN23 registers. The PxGA gain curve is shown in
Figure 36. The PxGA GAIN01 register contains nine bits each
for PxGA Gain0 and Gain1, and the PxGA GAIN23 register
contains nine bits each for PxGA Gain2 and Gain3.
18
15
12
9
0
127
255
383
511
639
767
895
1023
VGA GAIN REGISTER CODE
6
Figure 37. VGA Gain Curve (PxGA Not Included)
3
OPTICAL BLACK CLAMP
The optical black clamp loop is used to remove residual offsets
in the signal chain and to track low frequency variations in the
CCD’s black level. During the optical black (shielded) pixel in-
terval on each line, the ADC output is compared with a fixed
black level reference, selected by the user in the clamp level regis-
ter. The value can be programmed between 0 LSB and 255 LSB
in 256 steps. The resulting error signal is filtered to reduce noise,
and the correction value is applied to the ADC input through a
DAC. Normally, the optical black clamp loop is turned on once
per horizontal line, but this loop can be updated more slowly to
suit a particular application. If external digital clamping is used
during the postprocessing, the AD9949 optical black clamping
may be disabled using Bit D2 in the OPRMODE register. When
the loop is disabled, the clamp level register may still be used to
0
0
64
128
192
256
320
384
448
511
PxGA GAIN REGISTER CODE
Figure 36. PxGA Gain Curve
VARIABLE GAIN AMPLIFIER
The VGA stage provides a gain range of 6 dB to 42 dB, pro-
grammable with 10-bit resolution through the serial digital
interface. The minimum gain of 6 dB is needed to match a 1 V
input signal with the ADC full-scale range of 2 V. When com-
pared to 1 V full-scale systems, the equivalent gain range is 0
dB to 36 dB.
The VGA gain curve follows a linear-in-dB characteristic. The
exact VGA gain can be calculated for any gain register value by
using the equation
provide programmable offset adjustment
.
The CLPOB pulse should be placed during the CCD’s optical
black pixels. It is recommended that the CLPOB pulse duration
be at least 20 pixels wide to minimize clamp noise. Shorter pulse
widths may be used, but clamp noise may increase and the
ability to track low frequency variations in the black level will
be reduced. See the Horizontal Clamping and Blanking and
Applications Information sections for timing examples.
Gain (db) = (0.0351 × Code) + 6 dB
where the code range is 0 to 1023.
There is a restriction on the maximum amount of gain that can
be applied to the signal. The PxGA can add as much as 18 dB,
and the VGA is capable of providing up to 42 dB. However, the
maximum total gain from the PxGA and VGA is restricted to
42 dB. If the registers are programmed to specify a total gain
higher than 42 dB, the total gain is clipped at 42 dB.
DIGITAL DATA OUTPUTS
The AD9949 digital output data is latched using the DOUT
phase register value, as shown in Figure 28. Output data timing
is shown in Figure 19 and Figure 20. It is also possible to leave
the output latches transparent, so that the data outputs are valid
immediately from the ADC. Programming the AFE control
register Bit D4 to a 1 sets the output latches transparent. The
data outputs can also be disabled (three-stated) by setting the
AFE control register Bit D3 to a 1.
ADC
The AD9949 uses a high performance ADC architecture,
optimized for high speed and low power. DNL performance is
typically better than 0.5 LSB. The ADC uses a 2 V input range.
See Figure 9 and Figure 10 for typical linearity and noise
performance plots for the AD9949.
The data output coding is normally straight binary, but the
coding may be changed to gray coding by setting the AFE
control register Bit D5 to a 1.
Rev. B | Page 29 of 36
AD9949
APPLICATIONS INFORMATION
CIRCUIT CONFIGURATION
GROUNDING AND DECOUPLING
RECOMMENDATIONS
The AD9949 recommended circuit configuration is shown in
Figure 38. Achieving good image quality from the AD9949
requires careful attention to PCB layout. All signals should be
routed to maintain low noise performance. The CCD output
signal should be directly routed to Pin 27 through a 0.1 µF
capacitor. The master clock CLI should be carefully routed to
Pin 25 to minimize interference with the CCDIN, REFT, and
REFB signals.
As shown in Figure 38, a single ground plane is recommended
for the AD9949. This ground plane should be as continuous as
possible, particularly around Pins 23 to 30. This ensures that all
analog decoupling capacitors provide the lowest possible
impedance path between the power and bypass pins and their
respective ground pins. All high frequency decoupling
capacitors should be located as close as possible to the package
pins. It is recommended that the exposed paddle on the bottom
of the package be soldered to a large pad, with multiple vias
connecting the pad to the ground plane.
The digital outputs and clock inputs are located on Pins 1 to 13
and Pins 31 to 40 and should be connected to the digital ASIC
away from the analog and CCD clock signals. Placing series
resistors close to the digital output pins may help to reduce
digital code transition noise. If the digital outputs must drive a
load larger than 20 pF, buffering is recommended to minimize
additional noise. If the digital ASIC can accept gray code, the
AD9949’s outputs can be selected to output data in gray code
format using the control register Bit D5. Gray coding helps reduce
potential digital transition noise compared with binary coding.
All the supply pins must be decoupled to ground with good
quality, high frequency chip capacitors. There should also be a
4.7 µF or larger bypass capacitor for each main supply—AVDD,
RGVDD, HVDD, and DRVDD—although this is not necessary
for each individual pin. In most applications, it is easier to share
the supply for RGVDD and HVDD, which may be done as long
as the individual supply pins are separately bypassed. A separate
3 V supply may be used for DRVDD, but this supply pin should
still be decoupled to the same ground plane as the rest of the
chip. A separate ground for DRVSS is not recommended.
The H1–H4 and RG traces should have low inductance to avoid
excessive distortion of the signals. Heavier traces are recom-
mended because of the large transient current demand on
H1–H4 from the capacitive load of the CCD. If possible,
physically locating the AD9949 closer to the CCD will reduce
the inductance on these lines. As always, the routing path
should be as direct as possible from the AD9949 to the CCD.
The reference bypass pins (REFT, REFB) should be decoupled
to ground as close as possible to their respective pins. The
analog input (CCDIN) capacitor should also be located close to
the pin.
3V ANALOG SUPPLY
0.1µF
4
VD/HD/HBLK INPUTS
CLP/BLK OUTPUT
SERIAL
INTERFACE
3
1µF
1µF
D1
1
2
3
4
5
6
7
8
9
30 REFB
29 REFT
28 AVSS
27 CCDIN
26 AVDD
25 CLI
PIN 1
IDENTIFIER
D2
D3
0.1µF
D4
CCD SIGNAL
MASTER
CLOCK INPUT
DRVSS
DRVDD
D5
AD9949
TOP VIEW
3V
DRIVER
SUPPLY
0.1µF
+
24 TCVDD
23 TCVSS
22 RGVDD
21 RG
3V ANALOG
SUPPLY
4.7µF 0.1µF
+
D6
0.1µF
4.7µF
D7
D8 10
RG OUTPUT
RG DRIVER
SUPPLY
+
0.1µF
4.7µF
12
DATA
OUTPUTS
H DRIVER
SUPPLY
+
0.1µF
4.7µF
4
H1 TO H4
Figure 38. Recommended Circuit Configuration
Rev. B | Page 30 of 36
AD9949
DRIVING THE CLI INPUT
The AD9949’s master clock input (CLI) may be used in two
different configurations, depending on the application.
Figure 41 shows a typical dc-coupled input from the master
clock source. When the dc-coupled technique is used, the
master clock signal should be at standard 3 V CMOS logic
levels. As shown in Figure 42, a 1000 pF ac-coupling capacitor
may be used between the clock source and the CLI input. In this
configuration, the CLI input is self-biased to the proper dc volt-
age level of approximately 1.4 V. When the ac-coupled tech-
nique is used, the master clock signal can be as low as 500 mV
in amplitude.
AD9949
25
CLI
ASIC
MASTER CLOCK
Figure 41. CLI Connection, DC-Coupled
CCDIN
AD9949
27
AD9949
25
CLI
18
19
14
H1
15
H2
21
RG
LPF
H3
H4
ASIC
1nF
MASTER CLOCK
SIGNAL
OUT
Figure 42. CLI Connection, AC-Coupled
H1
H2
RG
HORIZONTAL TIMING SEQUENCE EXAMPLE
CCD IMAGER
Figure 43 shows an example CCD layout. The horizontal
register contains 28 dummy pixels, which occur on each line
clocked from the CCD. In the vertical direction, there are
10 optical black (OB) lines at the front of the readout and two at
the back of the readout. The horizontal direction has four OB
pixels in the front and 48 in the back.
Figure 39. CCD Connections (2 H-Clock)
CCDIN
27
AD9949
To configure the AD9949 horizontal signals for this CCD, three
sequences can be used. Figure 44 shows the first sequence that
should be used during vertical blanking. During this time, there
are no valid OB pixels from the sensor, so the CLPOB signal is
not used. PBLK may be enabled during this time, because no
valid data is available.
14
15
18
H3
19
H4
21
RG
H1
H2
SIGNAL
OUT
Figure 45 shows the recommended sequence for the vertical OB
interval. The clamp signals are used across the whole lines in
order to stabilize the clamp loop of the AD9949.
H3
H4
RG
CCD IMAGER
H2
H1
Figure 46 shows the recommended sequence for the effective
pixel readout. The 48 OB pixels at the end of each line are used
for the CLPOB signal.
Figure 40. CCD Connections (4 H-Clock)
Rev. B | Page 31 of 36
AD9949
SEQUENCE 2 (OPTIONAL)
2 VERTICAL OB LINES
USE SEQUENCE 3
EFFECTIVE IMAGE AREA
V
10 VERTICAL OB LINES
USE SEQUENCE 2
H
48 OB PIXELS
4 OB PIXELS
HORIZONTAL CCD REGISTER
28 DUMMY PIXELS
Figure 43. Example CCD Configuration
SEQUENCE 1: VERTICAL BLANKING
CCDIN INVALID PIX
VERTICAL SHIFT
DUMMY
INVALID PIXELS
VERT SHIFT
SHP
SHD
H1/H3
H2/H4
HBLK
PBLK
CLPOB
Figure 44. Horizontal Sequence During Vertical Blanking
SEQUENCE 2: VERTICAL OPTICAL BLACK LINES
OPTICAL
BLACK
VERTICAL SHIFT
DUMMY
OPTICAL BLACK
CCDIN
VERT SHIFT
SHP
SHD
H1/H3
H2/H4
HBLK
PBLK
CLPOB
Figure 45. Horizontal Sequences During Vertical Optical Black Pixels
Rev. B | Page 32 of 36
AD9949
SEQUENCE 3: EFFECTIVE PIXEL LINES
OPTICAL
BLACK
OB
OPTICAL BLACK
VERTICAL SHIFT
DUMMY
EFFECTIVE PIXELS
VERT SHIFT
CCDIN
SHP
SHD
H1/H3
H2/H4
HBLK
PBLK
CLPOB
Figure 46. Horizontal Sequences During Effective Pixels
Rev. B | Page 33 of 36
AD9949
OUTLINE DIMENSIONS
6.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
31
40
1
30
PIN 1
INDICATOR
0.50
BSC
4.25
4.10 SQ
3.95
TOP
VIEW
5.75
BCS SQ
EXPOSED
PAD
(BOTTOM VIEW)
0.50
0.40
0.30
21
10
11
20
0.25 MIN
4.50
REF
12° MAX
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
1.00
0.85
0.80
0.30
0.23
0.18
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VJJD-2
Figure 47. 40-Lead Lead Frame Chip Scale Package [LFCSP]
6 mm × 6 mm Body
(CP-40)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9949KCP
AD9949KCPRL
AD9949KCPZ1
AD9949KCPZRL1
AD9949AKCPZ1, 2
AD9949AKCPZRL1, 2
Temperature Range
−20°C to +85°C
−20°C to +85°C
−20°C to +85°C
−20°C to +85°C
−20°C to +85°C
−20°C to +85°C
Package Description
Package Option
CP-40
CP-40
CP-40
CP-40
40-Lead Lead Frame Chip Scale Package (LFCSP)
40-Lead Lead Frame Chip Scale Package (LFCSP)
40-Lead Lead Frame Chip Scale Package (LFCSP)
40-Lead Lead Frame Chip Scale Package (LFCSP)
40-Lead Lead Frame Chip Scale Package (LFCSP)
40-Lead Lead Frame Chip Scale Package (LFCSP)
CP-40
CP-40
1 Z = PB-free part.
2 The AD9949A is recommended for new designs and supports CCD line lengths > 4096 pixels.
Rev. B | Page 34 of 36
AD9949
NOTES
Rev. B | Page 35 of 36
AD9949
NOTES
© 2004 Analog Devices, Inc. All rights reserved. Trademarks and regis-
tered trademarks are the property of their respective owners.
D03751–0–11/04(B)
Rev. B | Page 36 of 36
相关型号:
AD9949KCPRLZ
IC SPECIALTY CONSUMER CIRCUIT, QCC40, 6 X 6 MM, MO-220-VJJD-2, LFCSP-40, Consumer IC:Other
ADI
©2020 ICPDF网 联系我们和版权申明