AD9870EB [ADI]
IF Digitizing Subsystem; 中频数字化子系统
| 型号： | AD9870EB |
| 厂家： | 
ADI |
| 描述： | IF Digitizing Subsystem |
| 文件： | 总20页 (文件大小：232K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
a
IF Digitizing Subsystem
AD9870
FEATURES
PRODUCT DESCRIPTION
10 MHz–300 MHz Input Frequency
Baseband (I/Q) Digital Output
10 kHz–150 kHz Output Signal Bandwidth
12 dB SSB NF
The AD9870 is a general-purpose IF subsystem that digitizes a
low-level 10 MHz–300 MHz IF input with a bandwidth of up to
150 kHz. The signal chain of the AD9870 consists of a low-noise
amplifier, a mixer, a variable gain amplifier with integral antialias
filter, a bandpass sigma-delta analog-to-digital converter, and a
decimation filter with programmable decimation factor. An auto-
matic gain control (AGC) circuit provides the AD9870 with
25 dB of continuous gain adjustment. The high dynamic range
of the bandpass sigma-delta converter allows the AD9870 to
cope with blocking signals that are as much as 70 dB stronger
than the desired signal. Auxiliary blocks include clock and LO
synthesizers as well as a serial peripheral interface (SPI) port.
> –1 dBm IIP3 (High IIP3 Mode)
25 dB Continuous AGC Range + 16 dB Gain Step
Support for LO and Sampling Clock Synthesis
Programmable Decimation Rate, Output Format, AAF
Cutoff, AGC and Synthesizer Settings
360 ꢂ Input Impedance
2.7 V–3.6 V Supply Voltage
Low Current: 42 mA Typ (High IIP3 Mode),
30 mA Typ (Low IIP3, Fixed Gain Mode)
48-Lead LQFP Package (1.4 mm Thick)
The SPI port programs numerous parameters of the AD9870,
including the synthesizer divide ratios, the AGC attack and decay
times, the AGC target signal level, the decimation factor, the
output data format, the 16 dB attenuator, and the bias currents of
several blocks. Reducing bias currents allows the user to reduce
power consumption at the expense of reduced performance.
APPLICATIONS
Portable and Mobile Radio Products
Digital UHF/VHF FDMA Products
TETRA
FUNCTIONAL BLOCK DIAGRAM
AGC
DAC
AD9870
–16dB
VGA/
AAF
DECIMATION
FILTER
ꢀ-ꢁ ADC
DOUTA
DOUTB
FS
FORMATTING/SSI
LNA
IFIN
f
= 18MHz
CLK
CLKOUT
FREF
CONTROL LOGIC
LO
SYNTH
SAMP CLOCK
SYNTHESIZER
VOLTAGE
REFERENCE
SPI
LO VCO AND
LOOP FILTER
CLK VCO AND
LOOP FILTER
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, norforanyinfringementsofpatentsorotherrightsofthirdpartiesthat
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
www.analog.com
© Analog Devices, Inc., 2001
AD9870–SPECIFICATIONS (VVDDDDPI == 5V.D0DVF, =CLVKD=DA18=M3S.P3SV,,FVIFD=DC73=.3V5DMDHLz=, F3LO.3=V7, 1V.D1DMDH=z,VuDnDleHss=o3t.h3eVrw, VisDeDnQo=ted.)
Parameter
Conditions1
Min
Typ
Max
Unit
OVERALL
Analog Supply Voltage
(VDDA, VDDF, VDDI)
Digital Supply Voltage
(VDDD, VDDC, VDDL)
Interface Supply Voltage
(VDDH)
Charge Pump Supply Voltage
(VDDP, VDDQ)
Total Current
2.7
2.7
1.8
2.7
3.0
3.0
3.6
3.6
3.6
V
V
V
3.0
42
12
12
–1
–10
360
0.6
5.5
50.6
V
High IIP3 Setting
High IIP3 Setting
Low IIP3 Setting
High IIP3 Setting
Low IIP3 Setting
mA
dB
dB
dBm
dBm
Ω
SSB Noise Figure @ Max VGA Gain
Input Third-Order Intercept (IIP3)
–5
Input Impedance
Gain Variation Over Temperature
dB
PREAMP + MIXER
Maximum Input and LO Frequencies
300
MHz
LO SYNTHESIZER
LO Input Frequency
LO Input Amplitude
FREF (Reference) Frequency
FREF Input Amplitude
Minimum Charge Pump Output Current
Maximum Charge Pump Output Current
Charge Pump Output Compliance Voltage2
Synthesizer Resolution
7.75
0.3
0.1
300
1.0
25
3
MHz
V p-p
MHz
V p-p
mA
mA
V
0.3
Programmable in 0.625 mA Steps
Programmable in 0.625 mA Steps
0.625
5.000
0.25
6.25
VDDP – 0.25
18
kHz
CLOCK SYNTHESIZER
CLK Input Frequency
CLK Input Amplitude
Minimum Charge Pump Output Current
Maximum Charge Pump Output Current
Charge Pump Output Compliance Voltage2
Synthesizer Resolution
13
0.3
MHz
V p-p
mA
mA
V
Clock VCO Off
Programmable in 0.625 mA Steps
Programmable in 0.625 mA Steps
0.625
5.000
0.25
2.2
VDDQ – 0.25
kHz
SIGMA-DELTA ADC
Resolution
Clock Frequency (fCLK
Center Frequency
Dynamic Range
16
Bits
MHz
MHz
dB
)
13
18
f
CLK/8
BW = 10 kHz
88
Passband Gain Variation
0.5
dB
DECIMATOR
Decimation Factor
Passband Width
Passband Gain Variation
Alias Attenuation
Programmable in Steps of 60
60
85
960
1
50
%
dB
dB
GAIN CONTROL
Programmable Gain Step
AGC Gain Range (Continuous)
AGC Attack Time
16
25
dB
dB
µs
18
40
60
7000
Programmable
SPI
PC Clock Frequency
PD Hold Time
10
MHz
ns
10
1
SSI
CLKOUT Frequency
Output Rise/Fall Time
18
120
45
16
10
MHz
ns
ns
ns
ns
CMOS Output Mode, Drive Strength = 0
CMOS Output Mode, Drive Strength = 1
CMOS Output Mode, Drive Strength = 2
CMOS Output Mode, Drive Strength = 3
OPERATING TEMPERATURE RANGE
Basic Functions
Meets All Specifications
–40
–40
+95
+85
°C
°C
NOTES
1Standard operating mode: high IIP3 setting, synthesizers in normal (not fast acquire) mode, fCLK = 18 MHz, 25 pF load on SSI output pins: VDDx = 3.0 V.
2Voltage span in which LO (or CLK) charge pump output current is maintained within 5% of nominal value of VDDP/2 (or VDDQ/2).
Specifications subject to change without notice.
–2–
REV. 0
AD9870
ABSOLUTE MAXIMUM RATINGS*
Parameter
With Respect to
Min
Max
Unit
VDDF, VDDA, VDDC, VDDD, VDDH,
VDDL, VDDI
GNDF, GNDA, GNDC, GNDD, GNDH
GNDL, GNDI, GNDS
–0.3
+4.0
V
VDDF, VDDA, VDDC, VDDD, VDDH,
VDDL, VDDI
VDDR, VDDA, VDDC, VDDD, VDDH,
VDDL, VDDI
–4.0
+4.0
V
VDDP, VDDQ
GNDP, GNDQ
–0.3
–0.3
+6.0
+0.3
V
V
GNDF, GNDA, GNDC, GNDD, GNDH GNDF, GNDA, GNDC, GNDD, GNDH
GNDL, GNDI, GNDQ, GNDP, GNDS
GNDL, GNDI, GNDQ, GNDP, GNDS
MXOP, MXON, LOP, LON, IFIN,
CXIF, CXVL, CXVM
PC, PD, PE, CLKOUT, DOUTA,
DOUTB, FS, SYNCB
GNDI
–0.3
–0.3
VDDI + 0.3
VDDH + 0.3
V
V
GNDH
IF2N, IF2P, GCP, GCN
VREFP, VREFN, VCM
IOUTC
IOUTL
CLKP, CLKN
GNDF
GNDA
GNDQ
GNDP
GNDC
GNDL
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
VDDF + 0.3
VDDA + 0.3
VDDQ + 0.3
VDDP + 0.3
VDDC + 0.3
VDDL + 0.3
150
V
V
V
V
V
V
°C
°C
°C
FREF
Junction Temperature
Storage Temperature
Lead Temperature (10 sec)
–65
+150
300
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device
at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum ratings for extended
periods may affect device reliability.
THERMAL CHARACTERISTICS
Thermal Resistance
48-Lead LQFP
θ
θ
JA = 91°C/W
JC = 28°C/W
ORDERING GUIDE
Package Description
Model
Temperature Range
Package Option
AD9870
AD9870EB
–40°C to +85°C
48-Lead Thin Plastic Quad Flatpack (LQFP)
Evaluation Board
ST-48
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD9870 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
–3–
REV. 0
AD9870
PIN CONFIGURATION
48 47 46 45 44 43 42 41 40 39 38 37
1
2
MXOP
MXON
GNDF
IF2N
36
35
34
33
32
31
30
29
28
27
26
25
GNDL
FREF
GNDS
SYNCB
GNDH
FS
PIN 1
IDENTIFIER
3
4
5
IF2P
AD9870
TOP VIEW
(Not to Scale)
6
VDDF
GCP
7
DOUTB
DOUTA
CLKOUT
VDDH
VDDD
PE
8
GCN
9
VDDA
GNDA
VREFP
VREFN
10
11
12
13 14 15 16 17 18 19 20 21 22 23 24
PIN FUNCTION DESCRIPTIONS
Pin Mnemonic
Pin Mnemonic Description
Description
1
2
3
4
5
6
7
8
MXOP
MXON
GNDF
IF2N
IF2P
VDDF
GCP
Mixer Output, Positive
Mixer Output, Negative
Ground for VGA
Second IF Input (to VGA), Negative
Second IF Input (to VGA), Positive
Positive Power Supply for Antialias Filter/VGA
Filter Capacitor for VGA Gain Control, Positive
Filter Capacitor for VGA Gain Control, Negative
Positive Power Supply for ADC
Ground for ADC
Voltage Reference, Positive
Voltage Reference, Negative
Common-Mode Voltage (Requires 20 kΩ to GNDA) 37
Pos. Power Supply for Clock Synth. Charge Pump
Clock Synthesizer Charge Pump Output Current
Ground for Clock Synthesizer Charge Pump
Positive Power Supply for Clock Synthesizer
Ground for Clock Synthesizer
Sampling Clock Input/Clock VCO Tank, Positive
Sampling Clock Input/Clock VCO Tank, Negative
Substrate Ground
25
26
27
28
29
30
31
32
33
34
35
36
PE
Enable Input for SPI Port
VDDD
VDDH
CLKOUT
DOUTA
DOUTB
FS
GNDH
SYNCB
GNDS
FREF
GNDL
GNDP
IOUTL
VDDP
VDDL
CXVM
LON
Positive Power Supply for Internal Digital Functions
Positive Power Supply for Digital Interface
Clock Output for SSI Port
Data Output for SSI Port
Data Output for SSI Port, Unused
Frame Sync for SSI Port
Ground for Digital Interface
Resets the SSI and Decimator Counters
Substrate Ground
Reference Frequency Input for Both Synthesizers
Ground for LO Synthesizer
Ground for LO Synthesizer Charge Pump
LO Synthesizer Charge Pump Output Current
Positive Power Supply for LO Synth. Charge Pump
Positive Power Supply for LO Synthesizer
External Capacitor for Mixer Bias
LO Input to Mixer and LO Synthesizer, Negative
LO Input to Mixer and LO Synthesizer, Positive
External Capacitor for Preamp Power Supply
Ground for Mixer and Preamp
GCN
9
VDDA
GNDA
VREFP
VREFN
VCM
VDDQ
IOUTC
GNDQ
VDDC
GNDC
CLKP
CLKN
GNDS
GNDD
PC
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
38
39
40
41
42
43
44
45
46
47
48
LOP
CXVL
GNDI
CXIF
IFIN
VDDI
Ground for Digital Functions
Clock Input for SPI Port
Data I/O for SPI Port
External Capacitor for Preamp Bias
First IF Input (to Preamp)
Positive Power Supply for Mixer and Preamp
PD
–4–
REV. 0
AD9870
SERIAL PERIPHERAL INTERFACE (SPI)
The Serial Peripheral Interface (SPI) is a bidirectional serial port. It is used to load configuration information into the registers listed
below as well as to read back their contents. Table I provides a list of the registers that may be programmed through the SPI port.
Addresses and default values are given in hexadecimal form.
Table I. SPI Address Map
Address Bit
(Hex) Breakdown
Width Default Value Name
POWER CONTROL REGISTERS
Description
0x00
0x01
(7:0)
8
0xFF
STBY
Standby Control Bits (REF, LO, CKO, CK, GC, LNAMX, VGA, ADC).
(7:6)
(5:4)
(3:2)
(1:0)
2
2
2
2
0
0
0
1
LNAB
MIXB
CKOB
ADCB
LNA Bias Current (0 = 0.5 mA, 1 = 1 mA, 2 = 2 mA, 3 = 3 mA).
Mixer Bias Current (0 = 1 mA, 1 = 2 mA, 2 = 3 mA, 3 = 4 mA).
CK Oscillator Bias (0 = 0.25 mA, 1 = 0.35 mA, 2 = 0.53 mA, 3 = 0.85 mA).
ADC Amplifier Bias (0 = 2.4 mA, 1 = 3.2 mA, 2 = 4.0 mA, 3 = 4.8 mA).
0x02
AGC
0x03
(7:0)
8
0x00
TEST
Factory Test Mode.
(7)
(6:0)
1
7
0
ATTEN
Apply 16 dB attenuation in the front end.
0x3F
AGCG(14:8) AGC Gain Setting (7 MSBs of a 15-bit two’s-complement word).
0x04
0x05
0x06
(7:0)
8
0xFF
AGCG(7:0) AGC Gain Setting (8 LSBs of a 15-bit two’s-complement word).
Default corresponds to maximum gain.
(7:4)
(3:0)
4
4
0
0
AGCA
AGCD
AGC Attack Time Setting. Default yields 50 Hz raw loop bandwidth.
AGC Decay Time Setting. Default is decay time = attack time.
(7:4)
(3:0)
(2:0)
4
4
3
0
0
0
AGCO
AGCD
AGCR
AGC Overload Update Setting. Default is slowest update.
Fast AGC (Minimizes resistance seen between GCN and GCP).
AGC Enable/Reference Level (disabled, 3 dB, 6 dB, 9 dB, 12 dB, 15 dB below clip).
DECIMATION FACTOR
0x07 (3:0)
LO SYNTHESIZER
4
4
M
Decimation Factor = 60 × (M + 1). Default is decimate-by-300.
0x08
0x09
(5:0)
(7:0)
6
8
0x00
0x38
LOR(13:8)
LOR(7:0)
Reference Frequency Divisor (6 MSBs of a 14-Bit Word).
Reference Frequency Divisor (8 LSBs of a 14-Bit Word).
Default (56) Yields 300 kHz from fREF = 16.8 MHz.
0x0A
(7:5)
(4:0)
3
5
0x5
0x00
LOA
LOB(12:8)
“A” Counter (Prescaler Control Counter).
“B” Counter MSBs (5 MSBs of a 13-Bit Word).
Default LOA and LOB Values Yield 300 kHz from 73.35 MHz–2.25 MHz.
0x0B
0x0C
(7:0)
8
0x1D
LOB(7:0)
“B” Counter LSBs (8 LSBs of a 13-Bit Word).
(6)
(5)
(4:2)
(1:0)
1
1
3
2
0
0
0
0
LOF
LOINV
LOI
Enable Fast Acquire.
Invert Charge Pump (0 = Pump_Up ⇒ IOUTL Sources Current).
Charge Pump Current in Normal Operation. IPUMP = (LOI + 1) × 0.625 mA.
Manual Control of LO Charge Pump (3 = Off, 2 = Down, 1 = Up, 0 = Normal).
LOTM
0x0D
0x0E
(3:0)
(7:0)
4
8
0x0
LOFA(13:8) LO Fast Acquire Time Unit (4 MSBs of a 14-Bit Word).
0x04
LOFA(7:0)
LO Fast Acquire Time Unit (8 LSBs of a 14-Bit Word).
CLOCK SYNTHESIZER
0x10
0x11
(5:0)
(7:0)
6
8
00
CKR(13:8)
CKR(7:0)
Reference Frequency Divisor (6 MSBs of a 14-Bit Word).
0x38
Reference Frequency Divisor (8 LSBs of a 14-Bit Word).
Default Yields 300 kHz from fREF =16.8 MHz.
Min = 3, Max = 16383.
0x12
(4:0)
5
0x00
CKN(12:8)
Synthesized Frequency Divisor (5 MSBs of a 13-Bit Word).
–5–
REV. 0
AD9870
Address Bit
(Hex)
Breakdown
Width Default Value Name
Description
CLOCK SYNTHESIZER (Continued)
0x13
0x14
(7:0)
8
0x3C
CKN(7:0)
Synthesized Frequency Divisor (8 LSBs of a 13-Bit Word).
Default Yields 300 kHz from fCLK = 18 MHz.
Min = 3, Max = 8191.
(6)
(5)
(4:2)
(1:0)
1
1
3
2
0
0
0
0
CKF
CKINV
CKI
Enable Fast Acquire.
Invert Charge Pump (0 = Pump_Up ⇒ IOUTC Sources Current).
Charge Pump Current in Normal Operation. IPUMP = (CKI + 1) × 0.625 mA.
Manual Control of CLK Charge Pump (0 = Off, 1 = Down, 2 = Up, 3 = Normal).
CKTM
0x15
0x16
(3:0)
(7:0)
4
8
0x0
CKFA(13:8) CK Fast Acquire Time Unit (4 MSBs of a 14-Bit Word).
0x04
CKFA(7:0)
CK Fast Acquire Time Unit (8 LSBs of a 14-Bit Word).
SSI CONTROL
0x18
(7:0)
8
0x12
SSICRA
SSI Control Register A. See Table III.
(Default is FS and CLKOUT Three-Stated.)
0x19
0x1A
(1:0)
(3:0)
2
4
0x0
1
SSICRB
SSIORD
SSI Control Register B. See Table III.
Output Rate Divisor. fCLKOUT = fCLK/SSIORD.
AAF CAPACITOR SETTING/CALIBRATION
0x1C
0x1D
(7:0)
8
0x00
AAR
Antialias Response Selector. 0x60 Is Recommended.
5
1
5
0
0x0
ERRN
CAPN
Error Flag.
AAF N-Well Capacitor Setting.
(4:0)
0x1E
5
(4:0)
1
15
0
0x0
ERRP
CAPP
Error Flag.
AAF Poly-Poly Capacitor Setting.
TEST REGISTERS AND SPI PORT READ ENABLE
0x38
0x39
0x3A
(7:0)
0
8
1
0x00
0
TEST
TEST
Factory Test Mode.
Factory Test Mode.
(7:4, 2:0)
(3)
7
1
0x0
0
TEST
SPIREN
Factory Test Mode.
Enable Read from SPI Port.
0x3B–
0x3F
(7:0)
1
0x00
TEST
Factory Test Mode.
–6–
REV. 0
AD9870
PC
PE
WRITE OPERATION:
READ OPERATION:
A5
A5
A0
A0
D7
D7
D6
D6
D0
PD
PD
D0
Figure 1. SPI Timing
Figure 1 illustrates the timing for the SPI port. After the periph-
eral enable (PE) signal goes low, data (PD) is read on the rising
edges of the clock (PC). The first bit is a read/not-write indica-
tor; the next six bits are address bits; the eighth bit is ignored;
the last eight bits are data. Address and data are given MSB first.
If the read/not-write indicator is a zero, a write operation occurs
and the data bits are shifted in. If the read/not-write indicator is
a one and if the read-back enable bit (Reg. 3A, Bit 3) has been
set, a read operation occurs and data is shifted out the data pin on
the falling edges of the clock. PE stays low during the operation
and goes high at the end of the transfer. If PE rises before an addi-
tional eight clock cycles have passed, the operation is aborted.
Table II. Max Legal SSIORD Values for 16-Bit I/O Data and
Decimation by 60 n
Bits per Sample
(Min No. of Bits per Frame)
EAGC = 0
EAGC = 1
EFS =1
EFS = 0
EFS = 0
EFS = 1
32
49
48/40*
69/59*
Output
Sample Rate
Dec’n (kSPS, for
Factor fCLK = 18 MHz) EFS = 0 EFS = 1 EFS = 0 EFS = 1
Max SSIORD Setting (Decimal)
EAGC = 0 EAGC = 1
If PE stays low for an additional eight clock cycles, the destina-
tion address is incremented and another eight bits of data are
shifted in. Again, should PE rise early, the current byte is ignored.
By using this implicit addressing mode, the entire chip can be
configured with a single write operation. Registers identified as
being subject to frequent updates, namely those associated with
power control and AGC operation, have been assigned adjacent
addresses to minimize the time required to update them. The auto-
increment mode is not supported for read operations.
M
0
1
2
3
4
5
6
7
8
9
60
300
150
100
75
60
50
42.857
37.5
33.333
30
27.272
25
23.077
21.428
20
1
1
1
1
120
180
240
300
360
420
480
540
600
3
5
2
3
2
3
1
2
7
4
5
3
9
5
7
8
9
10
11
13
14
15
15
15
15
6
7
8
4
5
5
6
7
8
9
10
11
11
12
13
11
13
14
15
15
15
15
15
15
15
15
Multibyte registers are “big-endian” (the most significant byte
has the lower address) and are updated when a write to the least
significant byte occurs.
10
11
12
13
14
15
15
15
15
10 660
11 720
12 780
13 840
14 900
15 960
SYNCHRONOUS SERIAL INTERFACE (SSI)
The primary output of the AD9870 is the converted signal, which
is available from the SSI port as a serial bit stream. The bit stream
consists of a 16-bit I word followed by a 16-bit Q word, where
each word is given MSB first and is in two’s-complement form.
AGC, signal strength, and synchronization information may also
18.75
be embedded in the data stream. The output bit rate (fCLKOUT
)
*If the AAGC Bit of SSICRA is set.
is equal to the modulator clock frequency (fCLK) divided by
Figure 2 illustrates the output timing of the SSI port for several
SSI control register settings. In the default mode of operation,
data is shifted out on rising edges of CLKOUT after a pulse is
output from the frame sync (FS) pin. As described above, the
output data consists of a 16-bit I sample followed by a 16-bit
Q sample plus two optional bytes containing AGC and status
information.
the contents of the SSIORD register. Users must verify that the
output bit rate is sufficient to accommodate the required num-
ber of bits per frame (see Table II) and that the chosen output
rate does not introduce harmful spurs. Idle (high) bits are used
to fill out each frame; the frame lengths listed in Table II
assume that with embedded frame sync (EFS = 1), at least 10
idle bits are desired.
–7–
REV. 0
AD9870
CLKOUT
FS
DOUT
I15
I0
Q15
Q14
Q0
SCKI = 0, SCKT = 0, SLFS = 0, SFSI = 0, EFS = 0, SFST = 0, EAGC = 0
CLKOUT
FS
DOUT
I15
I0
Q15
Q14
Q0
G15
G14
G0
SCKI = 0, SCKT = 0, SLFS = 0, SFSI = 0, EFS = 0, SFST = 0, EAGC = 1, AAGC = 0
CLKOUT
FS
HI-Z
START
BIT
START
BIT
START
BIT
STOP
BIT
I15
I8
I7
I0
Q15
STOP
BIT
DOUT
SCKI = 0, SCKT = 0, SLFS = X, SFSI = X, EFS = 1, SFST = 1, EAGC = 0
SCKI = 0, SCKT = 0, SLFS = X, SFSI = X, EFS = 1, SFST = 1, EAGC = 0: AS ABOVE, BUT FS IS LOW
IDLE (HIGH) BITS
CLKOUT
FS
DOUT
I15
I0
Q15
Q14
Q0
SCKI = 0, SCKT = 0, SLFS = 1, SFSI = 0, EFS = 0, SFST = 0, EAGC = 0
Figure 2. SSI Timing for Several SSICR Settings
EAGC = 0, AAGC = X: 32 DATA BITS
The two optional bytes are output if the EAGC bit of SSICRA
is set. The first byte contains the eight most significant bits of
the AGC DAC setting while the second byte contains a 2-bit
overload field, a 2-bit reset field, a 2-bit large-signal field, a zero
bit, and a trailing high bit. The overload, reset, and large-signal
fields contain the number of overload, reset, and large-signal
events since the last report, respectively, saturating at three
should the number of events equal or exceed this amount. The
two optional bytes follow the I and Q data as a 16-bit word
provided the AAGC bit of SSICRA is not set. If the AAGC bit
is set, the two bytes follow the I and Q data in an alternating
fashion. In this “alternate AGC data” mode, the LSB of the
byte containing the AGC DAC setting is zero; the LSB of the
byte containing reset/overload information is always a one.
Figure 3 illustrates the fields of the SSI data frames.
I (15:0)
Q (15:0)
EAGC = 1, AAGC = 0: 48 DATA BITS
AGC (7:0)
AGC (7:1)
I (15:0)
Q (15:0)
1
EAGC = 1, AAGC = 1: 40 DATA BITS
I (15:0)
I (15:0)
Q (15:0)
Q (15:0)
0
1
SAME
OVERLOAD COUNT
RESET COUNT
DON’T CARE
FGM
Figure 3. SSI Frame Structure
–8–
REV. 0
AD9870
When the embedded frame sync bit (EFS) is set, FS is either
low or in a high Z state (as determined by the SFST bit), and
framing information is embedded in the data stream. In this
mode, each eight bits of data are surrounded by a start bit (low)
and a stop bit (high), and each frame ends with at least 10 high
bits. Other control bits can be used to invert the frame sync (SFSI),
to delay the frame sync pulse by one clock period (SLFS), to invert
the clock (SCKI), or to set the clock (SCKT) to a high Z state.
Note that if EFS is set, SLFS is a don’t care.
Table IV. Standby Control Bits
Wake-
Up
Current
Reduction Time
STBY
Bit
Effect
(mA)1
(ms)
REF
Voltage Reference Off,
VREFP, VREFN in
High Z State.
1.5
1.0
(CREF
=
4.7 µF)
Note 2
LO
LO Synthesizer Off,
IOUTL in High Z State.
Clock Oscillator Off.
Clock Synthesizer Off,
IOUTC in High Z State.
Clock Buffer Off if
4.8
The AD9870 also provides the means for controlling the switch-
ing characteristics of the digital output signals. With a 25 pF
load, the rise and fall times of these signals are no more than
120 ns, 45 ns, 16 ns, or 10 ns if the DS (drive strength) setting
is 0, 1, 2, or 3, respectively.
CKO
CK
0.25
1.4
Note 2
Note 2
ADC Is Off.
Gain Control DAC Off.
GCP, GCN in High Z State.
Table III. SSI Control Registers
GC
3
Depends
on CGC
Name
Width
Description
LNAMX LNA and Mixer Off.
I(VDDI) = 0, CXVM,
10
SSICRA (ADDR = 0x18)
AAGC
EAGC
EFS
1
1
1
1
1
1
1
1
Alternate AGC Data Bytes
Embed AGC Data
Embed Frame Sync
CXVL, CXIF in High Z.
VGA
ADC
VGA/AAF Off.
6
0.1
0.1
IF2P, IF2N in High Z State.
ADC Off; Clock Buffer
Off if CK Synth. Off;
VCM in High Z State;
Clock-to-Digital Filter
Suspended; Digital
SFST
SFSI
SLFS
SCKT
SCKI
Three-State Frame Sync
Invert Frame Sync
Late Frame Sync (1 = Late, 0 = Early)
Three-State CLKOUT
Invert CLKOUT
13.8
Outputs Static.
SSICRB (ADDR = 0x19)
NOTES
DS
2
FS, CLKOUT, and DOUT Drive
Strength
1When all blocks are in standby, the master reference circuit is also put into
standby and thus the current is reduced by a further 0.4 mA.
2Wake-up time is application-dependent.
POWER CONTROL
LO SYNTHESIZER
To allow power consumption to be minimized, the AD9870
possesses numerous SPI-programmable power-down and bias
control bits.
The LO synthesizer shown in Figure 4 is a fully programmable
PLL capable of 6.25 kHz resolution at input frequencies up to
300 MHz and reference clocks of up to 25 MHz. It consists of a
low-noise digital Phase-Frequency Detector (PFD), a variable
output current charge pump (CP), a 14-bit reference divider,
programmable A and B counters and a dual-modulus 8/9 pres-
caler. The A (3-bit) and B (13-bit) counters, in conjunction
with the dual 8/9 modulus prescaler, implement an N divider
with N = 8 × B + A. In addition, the 14-bit reference counter
Each major block may be powered down through the appropri-
ate bit of the STBY register. This scheme provides the greatest
flexibility for configuring the IC to a specific application as well
as for tailoring the IC’s power-down and wake-up characteristics.
Table IV summarizes the function of each of the STBY bits.
Note, when all the blocks are in standby, the master reference
circuit is also put into standby and thus the current is reduced
by a further 0.4 mA.
(R Counter) allows selectable input reference frequencies, fREF
at the PFD input. A complete PLL (Phase-Locked Loop) can
,
be implemented if the synthesizer is used with an external loop
filter and VCO (Voltage Controlled Oscillator).
The AD9870 also allows control over the bias current in several
key blocks. The effects on current consumption and system
performance are described in the section dealing with the
affected block.
–9–
REV. 0
AD9870
The A, B, and R counters can be programmed via the following
registers: LOA, LOB, and LOR. The charge pump output current
is programmable via the LOI register from 0.625 mA to 5.0 mA
using the following equation: IPUMP = (LOI + 1) × 0.625 mA.
An on-chip lock detect function (enabled by the LOF bit) auto-
matically increases the output current for faster settling during
channel changes. The synthesizer may also be disabled using the
LO standby bit located in the STBY register.
Figure 5 shows the equivalent input structures of the synthesiz-
ers’ LO and REF buffers (excluding the ESD structures). The
LO input is fed to the LO synthesizers buffer as well as the
AD9870’s mixer’s LO port. Both inputs are self-biasing and
thus tolerate ac-coupled inputs. The LO input can be driven
with a single-ended or differential signal. Single-ended dc-
coupled inputs should ensure sufficient signal swing above and
below the common-mode bias of the LO and REF buffers (i.e.,
1.38 V and VDDL/2).
TO EXTERNAL
LOOP
FILTER
FREF
PHASE/
FREQUENCY
DETECTOR
REF
BUFFER
CHARGE
PUMP
fREF
ꢃR
LOP
LON
84kꢂ
LO
BUFFER
~VDDL/2
LOR
FAST
ACQUIRE
fLO
fREF
LOA, LOB
TO MIXER
LO PORT
fLO
FROM
VCO
LO
BUFFER
500ꢂ
500ꢂ
A, B
COUNTERS
ꢃ8/9
1.36V
BIAS
NOTE:
ESD DIODE STRUCTURES OMITTED FOR CLARITY
fREF STBY SWITCHES SHOWNWITH LO SYNTHESIZER ON
Figure 4. LO Synthesizer
The LO (and CLK) Synthesizer works in the following manner.
The reference frequency, fREF, is buffered and divided by the
value held in the R counter. The internal FREF is then compared
to a divided version of the VCO frequency, fLO. The phase/
frequency detector provides UP and DOWN pulses whose width
vary depending upon the difference in phase and frequency of
its two input signals. The UP/DOWN pulses control the charge
pump, making current available to charge the external low-pass
loop filter when there is a discrepancy between the inputs of the
PFD. The output of the low-pass filter feeds an external VCO
whose output frequency, FLO, is driven such that its divided
down version, FLO, matches that of FREF thus closing the feed-
back loop.
Figure 5. Equivalent Input of LO and REF Buffers
Fast Acquire Mode
The fast acquire circuit attempts to boost the output current
when the phase difference between the divided-down LO (i.e., fLO
and the divided-down reference frequency (i.e., fREF) exceeds
the threshold determined by the LOFA register. The LOFA
register specifies a divisor for the fREF signal, and it is the period
(T) of this divided-down clock that specifies the time interval
which controls the fast acquire algorithm.
)
Assume for the moment that the nominal charge pump current
is at its lowest setting (i.e., LOI = 0) and denote this minimum
current by I0. When the output pulse from the phase compara-
tor exceeds T, the output current for the next pulse is 2I0; when
the pulse is wider than 2T, the output current for the next pulse
is 3I0, and so forth, up to eight times the minimum output current.
If the nominal charge pump current is more than the minimum
value (i.e., LOI > 0), the preceding rule is only applied if it results
in an increase in the instantaneous charge pump current. If the
charge pump current is set to its lowest value (LOI = 0) and the
fast acquire circuit is enabled, the instantaneous charge pump
current will never fall below 2I0, even when the pulsewidth is
less than T. Thus the charge pump current when fast acquire is
enabled is given by
The synthesized frequency is related to the reference frequency
and the LO register contents as follows:
f
LO = (8 × LOB + LOA)/LOR × fREF
Note, the minimum allowable value in the LOB register is 3 and
its value must always be greater than that loaded into LOA. The
stability, phase noise, spur performance, and transient response
of the AD9870’s LO (and CLK) synthesizers are determined by
the external loop filter, the VCO, the N-divide factor, and the
reference frequency, fREF. An excellent reference book on PLL
synthesizers titled PLL Performance, Simulation and Design by Deen
Banerjee is available for free at www.national.com.
I
PUMP-FA = IO × (1 + max (1, LOI, Pulsewidth/T)).
An example may help illustrate how the values of LOA, LOB,
and LOR can be selected. Consider an application employing a
13 MHz crystal oscillator (i.e., fREF = 13 MHz) with the re-
quirement that FREF = 100 kHz and fLO = 143 MHz (i.e.,
high-side injection with IF = 140.75 MHz and fSAMPLE = 18
MSPS). LOR is selected to be 130 such that fREF = 100 kHz.
The N-divider factor is 1430, which can be realized by select-
ing LOB = 178 and LOA = 6.
–10–
REV. 0
AD9870
VDDC=3.0V
The recommended setting for LOFA is LOR/16. Choosing a
larger value for LOFA will increase T. Thus, for a given phase
difference between the LO input and the fREF input, the instan-
taneous charge pump current will be less than that available for
a LOFA value of LOR/16. Similarly, a smaller value for LOFA
will decrease T, making more current available for the same
phase difference. In other words, a smaller value of LOFA will
enable the synthesizer to settle faster in response to a frequency
hop than will a large LOFA value. Care must be taken to choose
a value of LOFA which is large enough (values greater than four
recommended) to prevent the loop from oscillating back and
forth in response to a frequency hop.
LOOP
R
BIAS
FILTER
C
OSC
L
R
OSC
D
0.1ꢄF
C
VAR
CLKN
CLKP
IOUTC
AD9870
V
= VDDC – R
ꢅ I
> 1.6V
BIAS
CM
BIAS
–1/2
))
OSC
fOSC > (2 ꢅ L
ꢅ(C
//C
ꢆ
OSC
VARACTOR
Table V. SPI Registers Associated with LO Synthesizer
CLK OSC. BIAS
I
= 0.25, 0.35,
BIAS
A
(Hex)
ddress Bit
0.53, OR 0.85 mA
2
Breakdown Width
Default Value Name
0x00
0x08
0x09
0x0A
(7:0)
(5:0)
(7:0)
(7:5)
(4:0)
(7:0)
(6)
8
6
8
3
5
8
1
1
3
2
4
8
0xFF
0x00
0x38
0x5
0x00
0x1D
0
0
0
0
0x0
0x04
STBY
Figure 6. External Loop Filter, Varactor and L-C Tank Are
Required to Realize a Complete Clock Synthesizer
LOR(13:8)
LOR(7:0)
LOA
LOB(12:8
LOB(7:0)
LOF
LOINV
LOI
LOTM
The AD9870 clock synthesizer circuitry includes a negative-
resistance core so that only an external L-C tank circuit with a
varactor is needed to realize a voltage controlled oscillator (VCO).
Figure 6 shows the external components required to complete
the clock synthesizer along with the equivalent input of the CLK
input. The resonant frequency of the VCO is approximately deter-
mined by LOSC and the series equivalent capacitance of COSC and
0x0B
0x0C
(5)
(4:2)
(1:0)
(3:0)
(7:0)
CVAR. As a result, LOSC, COSC, and CVAR should be selected to
0x0D
0x0E
LOFA(13:8)
LOFA(7:0)
provide sufficient tuning range to ensure proper locking of the
clock synthesizer The bias, IBIAS, of the negative-resistance core
has four programmable settings. Lower equivalent Q of the L-C
tank circuit may require a higher bias setting of the negative-
resistance core to ensure proper oscillation. RBIAS should be
selected such that the common-mode voltage at CLKP and
CLKN is approximately 1.6 V. The synthesizer may be disabled
via the CK standby bit to allow the user to employ an external
synthesizer and/or VCO in place of those resident on the IC.
CLOCK SYNTHESIZER
The clock synthesizer is a fully programmable integer-N PLL
capable of 2.2 kHz resolution at clock input frequencies up to
18 MHz and reference frequencies up to 25 MHz. It is similar
to the LO synthesizer described previously in Figure 4 with the
following exceptions:
•
•
It does not include an 8/9 prescaler nor an A Counter.
It includes a negative-resistance core which when used in
conjunction with an external varactor serves as the VCO.
Table VI. SPI Registers Associated with CLK Synthesizer
A
ddress
Bit
The 14-bit reference counter and 13-bit N-divider counter can
be programmed via the following registers: CKR and CKN. The
charge pump current is programmable via the CKI register
from 0.625 mA to 5.0 mA using the following equation:
(Hex)
Breakdown Width
Default Value Name
0x00
0x01
0x10
0x11
0x12
0x13
0x14
(7:0)
(3:2)
(5:0)
(7:0)
(4:0)
(7:0)
(6)
8
2
6
8
5
8
1
1
3
1
4
8
0xFF
0
STBY
CKOB
00
CKR(13:8)
CKR(7:0)
CKN(12:8)
CKN(7:0)
CKF
I
PUMP = (CKI + 1) × 0.625 mA.
0x38
0x00
0x3C
0
The fast acquire subcircuit of the charge pump is controlled by
the CKFA register in the same manner as the LO synthesizer is
controlled by the LOFA register. An on-chip lock detect func-
tion (enabled by the CKF bit) automatically increases the output
current for faster settling during channel changes. The synthe-
sizer may also be disabled using the CKOB standby bit located
in the STBY register.
(5)
0
CKINV
(4:2)
(1:0)
(3:0)
(7:0)
0
CKI
0
CKTM
0x15
0x16
0x0
0x04
CKFA(13:8)
CKFA(7:0)
–11–
REV. 0
AD9870
IF1 LNA/MIXER
Both the LNA and mixer have four programmable bias settings
so that current consumption can be minimized for a given appli-
cation. Figures 7c, 7d, and 7e show how the LNA and mixer’s
noise figure (NF), linearity (IIP3), conversion gain, current
consumption and frequency response are all affected for a given
LNA/Mixer bias setting. The measurements were taken at an IF
= 73.35 MHz, an LO = 71.1 MHz, and supplies set to 3.0 V.
Note, since the current consumption of the LNA/Mixer portion
of the IC can be reduced by only 5 mA at most relative to the
nominal current consumption of the entire IC in the high IIP3
mode (i.e., 42 mA), most applications will benefit with the
AD9870’s LNA/Mixer configured for the high bias mode (i.e.,
LNAB = 3, MIXB = 3 for SPI Port Register 1).
The AD9870 contains a single-ended LNA followed by “Gilbert-
type” active mixer as shown in Figure 7a. The mixer’s differential
LO port is driven by an LO buffer stage which can be driven
single-ended or differential. The LO signal level can range from
0.3 V p-p to 1.0 V p-p with negligible effect on performance.
The input impedance at the IFIN pin is 360 Ωʈ2 pF ( 20%)
and has no significant variation with respect to the programmable
bias settings. Figure 7b. shows the S11 parameters of the AD9870
with the following LNA/Mixer bias setting: LNAB = 3, MIXB = 3.
180ꢂ
180ꢂ
MIXER GAIN = –5 dB
LNA GAIN = 15 dB
12
CONVERSION
GAIN
11
10
R
BIAS
LO INPUT =
0.3TO 1.0V p–p
R
GAIN
MULTI-TANH
V–I STAGE
VCML
9
R
F
NOISE
FIGURE
8
R
= 360ꢂ
IN
DC SERVO
LOOP
7
6
Figure 7a. Simplified Schematic of AD9870’s LNA/Mixer
0–0 0–1 0–2 0–3 1–0 1–1 1–2 1–3 2–0 2–1 2–2 2–3 3–0 3–1 3–2 3–3
LNA-MIXER POWER BIAS SETTING
J50
Figure 7c. LNA/Mixer Noise Figure and Conversion Gain
vs. Bias Setting
J100
J25
9
8
7
6
5
4
3
2
1
0
5
LNA–MIXER
CURRENT
J200
0
J10
J400
–5
323–J105
AT 73.35 MHz
IIP3
0
10
25
50
100
200 400
–10
–15
–20
–25
255–J163
AT 140 MHz
–J400
166–J177
–J10
AT 240 MHz
–J200
–J25
–J100
0–0 0–1 0–2 0–3 1–0 1–1 1–2 1–3 2–0 2–1 2–2 2–3 3–0 3–1 3–2 3–3
LNA-MIXER POWER BIAS SETTING
–J50
Figure 7d. LNA/Mixer IIP3 and Current Consumption vs.
Bias Setting
Figure 7b. Input Impedance (i.e. S11) of the AD9870’s
IF1 Input
–12–
REV. 0
AD9870
1
0
The AAF tuning algorithm works in the following manner. The
AD9870 measures the oscillation frequency of an on-chip RC
oscillator relative to the frequency applied to the CLKP, CLKN
pins. It then uses this measurement in conjunction with the AAR
setting to program the capacitors of the AAF which sets the filters
poles. The on-chip circuitry sets the capacitor-programming
registers (CAPN and CAPP) to the required values based on the
clock frequency and the AAR setting.
–1
–2
–3
–4
–5
–6
3–3 BIAS
SETTING
2–2 BIAS
SETTING
The recommended –3 dB cutoff frequency is fCLK/3.2 (selected
by setting AAR = 0x60) since it provides minimal signal attenu-
ation in the passband region of fCLK/8 and sufficient attenuation
of the potential alias components in the transition band region.
For this setting the frequency-scaling resolution is sufficient to
yield less than 10% tuning error with clock frequencies between
13 MHz and 18 MHz. Figure 9a shows the measured response
of the antialias filter when it has been tuned with AAR = 0x60 at
an ADC clock frequency of 18 MHz. The multiple curves show
the possible tuning error due to the finite resolution of the tun-
ing capacitors. In this example, the capacitor across the mixer
load resistors yields a pole at 5 MHz, which degrades the mixer
gain at 2.25 MHz by approximately 0.8 dB. The nominal –3 dB
cutoff frequency of the antialias filter is 5.6 MHz. The nominal
attenuation at the first alias (15.75 MHz) is 28 dB and falls at
60 dB/decade so that the nominal attenuation at 50 MHz is 60 dB.
1–1 BIAS
SETTING
0–1 BIAS
SETTING
10
100
1000
FREQUENCY – MHz
Figure 7e. LNA/Mixer Frequency Response vs. Bias
Setting
Table VII. SPI Registers Associated with LNA/Mixer
A
(Hex)
ddress
Bit
Breakdown Width
Default Value Name
0
x01
(7:6)
(5:4)
(7)
2
2
1
0
0
0
LNAB
MIXB
ATTEN
0x01
0x03
5
–5
ANTIALIAS FILTER
2.25MHz IF @ CLK = 18MSPS
The AD9870 includes a programmable continuous-time third
order antialias filter (AAF) as shown in Figure 8. Its purpose is
to suppress any noise or spectral components occurring at N ×
fCLK (fCLK/8) from aliasing back into the sigma-delta ADC’s
passband centered at fCLK/8. It consists of a programmable
capacitor at the mixer output providing a real pole plus a second
order programmable filter built into the VGA providing a com-
plex pole pair.
–15
–25
–35
–45
–55
–65
I-V 2ND ORDER LPF
R2
0.1
1
10
100
FREQUENCY – MHz
C2
MIXER
(5MHz LOWPASS)
Figure 9a. Antialias filter response with AAR = 0x60 and
CLK = 18 MHz. Note, the curves have been normalized
individually to 0 dB at f0 = 2.25 MHz.
R1
f
R0
C0
G
G
C1
m0
m1
180ꢂ
Since the frequency measurements are performed relative to the
clock frequency, the AAF’s normalized frequency response
remains relatively independent of the ADC clock frequency.
There is guaranteed to be sufficient range in the programmable
capacitor arrays to support the response of Figure 9a for clock
frequencies between 13 MHz and 18 MHz with the resolution
indicated. Also, the normalized frequency response of the AAF
remains relatively independent of the programmed –3 dB cutoff
frequency over a 13 MHz to 18 MHz frequency range as shown
in Figure 9b. If the user specifies an unattainable response, the
on-chip circuitry sets CAPN and/or CAPP to the limit of their
ranges and also sets the ERRN and/or ERRP bit to indicate that
the specified response cannot be supported.
C0 AND C1 CONSIST OF 36 NWELL CAPACITORS IN PARALLEL
C3 CONSIST OF 36 POLY-POLY CAPACITORS IN PARALLEL
Figure 8. Equivalent Circuit of Antialias Filter
The AAF is typically tuned during the start-up phase of the
AD9870. The user initiates tuning of the AAF by writing a value to
the AAR (antialias response) register. The following two consid-
erations should be noted when tuning the AAF response. First,
the accuracy of the tuning algorithm is sensitive to on-chip
digital noise. Thus, placing the ADC in standby (i.e., register STBY)
prior to tuning the AAF is recommended. Second, although the
default setting of the AAR register is 0x00, writing 0x00 is not recom-
mended since all subsequent writes to this register will be ignored
until power to the AD9870 is reapplied to reset this register.
–13–
REV. 0
5
Table VIII. SPI Registers Associated with AAF
–5
fCLK/8
Address
(Hex)
Bit
–15
–25
–35
–45
–55
–65
–75
–85
–95
Breakdown Width
Default Value Name
0x1C
0x1D
(7:0)
5
(4:0)
5
8
1
5
1
0x00
0
AAR
fCLK = 13MSPS
ERRN
CAPN
ERRP
CAPP
0x0
0
0x1E
fCLK = 15MSPS
fCLK = 18MSPS
(4:0)
15
0x0
VARIABLE GAIN AMPLIFIER OPERATION WITH
AUTOMATIC GAIN CONTROL
The AD9870 contains a variable gain amplifier (VGA) as well as
all of the necessary signal estimation and control circuitry to
implement automatic gain control (AGC) as shown in Figure
10. The AGC control circuitry provides a high degree of pro-
grammability to allow the user to optimize the AGC response as
well as the AD9870’s dynamic range for a given application.
The VGA is programmable over a 25 dB (typ) range and imple-
mented in the same circuitry as the AAF circuitry previously
discussed. Since its input is self-biasing and presents a high
impedance to the mixer output load, the differential output
signal appearing at the mixer output (MXOP, MXON) must be
ac coupled to the VGA input (IF2P, IF2N) with 0.1 µF ceramic
chip capacitors. Note, an external 20 kΩ resistor in parallel with a
0.1 µF capacitor from VCM (Pin 13) to GNDA is required to ensure
common-mode compatibility between the ADC input and VGA output.
0.01
0.1
FREQUENCY – MHz
1
10
Figure 9b. Measured Normalized AAF Frequency Response
for AAR = 0 × 60 Setting with fCLK = 13, 15, and 18 MHz
5
AAR = 0 ꢅ 30
–5
–15
AAR = 0 ꢅ C0
–25
–35
AAR = 0 ꢅ 60
–45
The purpose of the VGA is to extend the usable dynamic range
of the AD9870 by allowing the sigma-delta ADC to digitize low
level signals in the presence of larger unfiltered interferer signals
without saturation or “clipping” the ADC. The VGA can oper-
ate in either a user controlled variable gain control mode or
automatic gain control (AGC) mode. The VGA may also be
disabled using the VGA standby bit located in the STBY register.
–55
–65
0.1
1
10
100
FREQUENCY – MHz
Figure 9c. Measured AAF Frequency Response for Differ-
ent AAR Settings with fCLK = 18 MHz
Note, ideally the quiescent current of the VGA circuitry should
reduced from 6 mA to 0 mA when the standby is invoked. How-
ever, it has been found that the standby current increases to
1.3 mA a few seconds (temperature dependent) after placing
the VGA in standby. Hence, the user is recommended to write
to the STBY register periodically (0.1 kSPS) and toggle the
VGA bit (i.e., write 0 followed by 1) to ensure that the standby
current remains at approximately 0 mA.
Changing the AAR setting from the recommended value of 0 × 60
scales the frequency axis in an inverse way as shown in Figure
9c. For example, to scale the frequency response down by a
factor of 1.5 set the AAR register to 1.5 times 0 × 60 (i.e., 0 × 90).
This AAR setting will not cause an error flag to be set for fCLK
= 18 MHz since the 3.7 MHz cutoff is within the guaranteed
range. For fCLK = 18 MHz, this AAR setting would increase the
attenuation at the first alias by 10 dB, lower the –3 dB cutoff
from 5.6 MHz to 3.7 MHz, and reduce the mixer gain by 0.8 dB
due to the reduced mixer pole frequency. However, reducing
fCLK
ꢃ20
f
CLK to 13 MHz while using the same AAR setting in many parts
IF2P
IF2N
I
DEC1
VGA/
AAF
j(2ꢆf
/8)t
ꢀ-ꢁADC
e
CLK
may cause a deviation in the normalized frequency response
since the –3 dB cutoff of 2.7 MHz is well below the 3.5 MHz
lower limit. In general, –3 dB cutoff frequencies can be approxi-
mated by the following equation:
ꢃ20
Q
ADC
CLIP POINT
A
(I[N])+A (Q[N])
BS
BS
OLW
f
–3 dB = (fCLK/3.2) × (0 × 60/AAR)
1
(1–Z
AGC
CONTROL
VGA
DAC
where AAR is the hexadecimal contents of the AAR register and
0 × 60 is its hexadecimal default setting.
–1
AGCR
REF LEVEL
)
C
DAC
/20
fCLK
Figure 10. Functional Block Diagram of VGA and AGC
–14–
REV. 0
AD9870
Variable Gain Control
A description of the AGC control algorithm and the user adjust-
able parameters follows. First consider the situation in which the
in-band signal is bigger than all out-of-band signals. In this case,
the amplitude of the in-band signal will be tracked to the pro-
grammed reference level by the AGC using the output of the
digital estimation block. If the difference is negative (i.e., the
signal is too large), the gain is decreased with a proportionality
constant determined by the AGCA setting. Large AGCA values
result in large gain changes thus rapid tracking of changes in
signal strength. If the difference between the target and estimated
signal level is positive (i.e., the signal is too small), the gain is
increased but now the proportionality constant is determined by
both the AGCA and AGCD settings. AGCD is effectively sub-
tracted from AGCA, so large AGCD results in smaller gain
changes and thus slower tracking of fading signals.
When in variable gain mode, the gain of the VGA can be adjusted
by writing to the 16-bit AGCR register. Note, proper loading of
the AGCR register requires that address 0x03 always be writ-
ten prior to 0x04. The maximum update rate of the AGCG
register is fCLK/100. The MSB of this register is the bit which
enables 16 dB of attenuation in the preamp. This feature
allows the AD9870 to cope with large level signals beyond
the VGA’s range to prevent overloading of the ADC.
The gain of the VGA is set by an 8-bit control DAC which
provides a differential control signal to the VGA appearing at
pins GCP and GCN. Two external 0.1 µF capacitors, CDAC
from GCP and GCN to analog ground, are required to “smooth”
,
or filter the DAC’s output each time it updates. Note, the dif-
ferential equivalent value of these two capacitors (i.e., CDAC/2
in combination with the DAC’s programmable output resis-
tance sets the –3 dB bandwidth and time constant associated
with this RC network.
)
The 4-bit code in the AGCA field sets the raw bandwidth of the
AGC loop. With AGCA = 0, the AGC loop bandwidth is at its
minimum of 50 Hz. Each increment of AGCA increases the
loop bandwidth by a factor of 21/2; thus the maximum band-
width is 9 kHz. A general expression for the attack bandwidth is
Automatic Gain Control (AGC)
The gain of the VGA is automatically adjusted when the AGC is
enabled via the AGCR register. In this mode, the gain of the
VGA is continuously updated in an attempt to ensure that the
maximum signal level into the ADC does not exceed a fixed
analog ADC clip level and that the rms output level of the ADC
is equal to a programmable reference level. This programmable
level can be set at 3 dB, 6 dB, 9 dB, 12 dB, and 15 dB below
the ADC saturation (clip level) by writing values from 1 to 5 to
the 3-bit AGCR field. Note, the ADC clip level is defined to be
–2 dBFS of its full-scale (i.e., 0.28 V rms). If AGCR is 0, auto-
matic gain control is disabled.
BWA = 50 × (fCLK/18 MHz) × 2(AGCA/2) Hz
(2)
The attack time may be estimated from the loop bandwidth if
one assumes that the loop dynamics are essentially that of a
single-pole system as described by the following equation.
t
ATTACK = 2.2/(100 × × 2AGCA/2) = 0.35/BWA
(3)
This approximation is good if the extra pole caused by the RC
filter on the DAC output is at a sufficiently high frequency. If
the RC pole is placed at four times the raw AGC pole (i.e.,
RC = 1/(8 × π × BW)) then Equation 3 yields an attack time
which is high by about 25%. A more accurate formula for this
case is to replace the 2.2 in the numerator of Equation 3 by 1.7.
The AGC control loop and estimation circuitry are implemented
both in the analog and digital domain to cope with out-of-band
interferers and in-band signals which could otherwise overload
the ADC. If the largest signal into the ADC falls outside the
passband of the first stage digital filter and exceeds the ADC
clip level of –2 dBFS, a control loop based on an analog com-
parator is used to reduce the VGA gain and prevent ADC clipping.
If the largest signal into the ADC is the target signal (and/or
interferer) falling within the passband defined by the first deci-
mation filter (but below the ADC clip level), a control loop
based on a digital estimation of the signal power is used to con-
trol the VGA gain.
The 4-bit code in the AGCD field sets the ratio of the attack
time to the decay time in the amplitude estimation circuitry.
When AGCD is zero, this ratio is one. Incrementing AGCD
multiplies the decay time-constant by 21/2, allowing a 180:1
range in the decay time relative to the attack time. The decay
time may be computed from
t
DECAY = tATTACK × 2 (AGCD/2)
(4)
The 4-bit code in the AGCO field sets the weighting applied
to gain updates when overload is detected. Each increment in
AGCO doubles the weighting factor. At the highest AGCO
setting, each reset event will cause a 6 dB reduction in the
VGA gain.
Referring to Figure 10, an analog comparator is used to com-
pare the VGA output (or ADC input) to a reference threshold
which is close to that of the ADC clip level. The output of the
comparator will be a digital signal named “OLW” which drives
the digital integrator within the AGC control loop when an over-
load condition is detected. Note, the detection of an overload
condition via this analog signal estimation path takes precedence
over the digital signal estimation path in the AGC control loop
until the analog overload condition is removed. For signals
falling within the passband of the first stage decimate-by-20
digital filter, the rms power of the I and Q signal is estimated
digitally by the following equation:
Lastly, the AGCF bit reduces the DAC source resistance by a
factor of 8. This facilitates fast acquisition by lowering the RC
time constant which is formed with the external capacitors
connected from the GCP and GCN pins to ground. For an
overshoot-free step response in the AGC loop, the capacitors
should be chosen such that the RC time constant is less than
one quarter that of the raw loop. Specifically,
RC Յ 1/(8 π BW)
(5)
where R is the resistance between the GCN and GCP pins and
ground (30 kΩ 30% if AGCF = 0, <3.8 kΩ if AGCF = 1) and
BW is the raw loop bandwidth. Note that with C chosen at this
upper limit, the loop bandwidth increases by approximately 30%.
XEST[N] = ABS(I[N]) + ABS(Q[N])
(1)
As a result, the VGA and other registers involved in the AGC
algorithm are updated at fCLK/20. The number of overload and
ADC reset occurrences within the final I/Q update rate of the
AD9870 as well as the AGC value (8 MSBs) can be read from
the SSI data upon proper configuration.
–15–
REV. 0
AD9870
Table IX. SPI Registers Associated with AGC
DECIMATION FILTER
The decimation filter consists of a complex mix by fCLK/8 and a
cascade of three linear phase FIR filters: DEC1, DEC2, and DEC3
as shown in Figure 12. DEC1 downsamples by a factor of 20
using a fourth-order comb filter. DEC2 also uses a fourth-
order comb filter, but its decimation factor is set by the M
control register. DEC3 is a decimate-by-3 FIR filter.
A
(Hex)
d
dress
Bit
Breakdown
Default
Value
Width
Name
0x03
(7)
1
7
8
4
4
4
4
3
0
ATTEN
AGCG(14:8)
AGCG(7:0)
AGCA
AGCD
AGCO
(6:0)
(7:0)
(7:4)
(3:0)
(7:4)
(3:0)
(2:0)
0x3F
0xFF
0x04
0x05
0
0
0
0
0
M
COS
I
0x06
DEC1
4
DEC2
4
DEC3
AGCD
AGCR
COMPLEX
DATA TO
SSI PORT
SIN
DATA FROM
MODULATOR
FIR
FILTER
SINC
SINC
20
M + 1
3
FILTER
FILTER
Q
System Noise Figure (NF) vs. VGA (or AGC) Control
The AD9870’s system NF is a strong function of the gain set-
ting of the VGA. The noise present at the output of the VGA
and input of the ADC is relatively large and independent of the
VGA setting. Under small signal conditions in which the VGA is
set to its maximum gain, this noise referred back to the input of
the LNA’s input has less of an effect on raising the AD9870’s
system NF. However, under large signal conditions in which the
gain of the VGA must be reduced to prevent ADC clipping, this
noise quickly becomes a significant contributor in determining
the AD9870’s overall NF. Figure 11 shows how the NF of the
AD9870 in AGC mode remains relatively constant as an inter-
ferer signal input power is increased until its power reaches a
programmed reference level (i.e., –3 dB) at which point the NF
degrades almost 1 dB per dB as the interferer signal is increased
beyond this point, forcing the VGA gain to decrease. As a result, it
is recommended that the AGC referenced level be set to 3 (i.e.,
AGCR = 1) to maintain the best possible NF over the widest
input signal range.
Figure 12. Decimation Filter Architecture
Figure 13a shows the response of the complete decimation filter
on a linear frequency axis for frequencies up to the third alias.
As this figure shows, the alias with the least attenuation is
located at the lower end of the third alias band and has an
attenuation of 83 dB.
0
–20
ꢇ5kHz PASSBAND
83dB ATTENUATION
(MIN)
88dB ATTENUATION
(MIN)
FOLDING
POINT
–40
–60
>100dB ATTENUATION
–80
150
45
42
39
36
–100
0
10
20
30
40
50
60
70
ADC CLIPS
AT –24 dBm
FREQUENCY – kHz
100
MEAN AGCVALUE
Figure 13a. Frequency Response for fCLKOUT = 20 kHz,
Showing the First Three Alias Bands
50
0
33
30
Figure 13b shows the full response of the decimation filter with
the decimation factor set to 60 on a logarithmic frequency
scale, while Figure 13c shows the folded frequency response
on a linear frequency scale and Figure 13d shows a blowup of
the passband. The location of the cutoff frequency shown in Figure
13b is inversely proportional to the decimation factor. However,
since both DEC1 and DEC2 are fourth-order comb filters, their
combination is also a fourth-order comb filter and thus the
shapes of the frequency responses shown in Figures 13c and
13d are independent of the decimation factor.
27
24
21
18
15
12
9
–50
NOISE FIGURE
–100
–150
–85 –80 –75 –70 –65 –60 –55 –50 –45 –40 –35 –30 –25 –20
INTERFERER AMPLITUDE – dBm
Figure 11. Noise Figure vs. Interferer Signal Level with an
IF = 73.35 MHz and CLK = 18 MSPS and AGCR = 1
–16–
REV. 0
AD9870
0
–20
Evaluation Board and Software
The evaluation board along with its accompanying software
provide a simple means to evaluate the AD9870. The block
diagram in Figure 14 shows the major blocks of the evaluation
board. The evaluation board is designed to be flexible allowing
the user to configure it for different potential applications. The
power supply distribution block provides filtered, adjustable
voltages to the various supply pins of the AD9870. In the IF
Input signal path, component pads are available to implement
different IF impedance matching networks. The LO and CLK
signals can be externally applied or internally derived from a
user-supplied VCO Module interface daughter board. The refer-
ence for the on-chip LO and CLK synthesizers can be applied
via the external FREF input or an on-board crystal oscillator.
–40
–60
–80
–100
–4
–3
–2
–1
10
10
10
10
BASEBAND FREQUENCY – Relative to fCLK
Figure 13b. Decimator Frequency Response
IF
LO
INPUT INPUT
0
VCO
MODULE
INTERFACE
FREF
INPUT
MIXER
OUTPUT
AD9870
OR
AD9874
–20
–40
CRYSTAL
OSCILLATOR
NIDAQ
XILINX
SPARTON
FPGA
IDT
FIFO
(OPTIONAL)
68-PIN
CONNECTOR
–60
AD9870/AD9874
POWER SUPPLY
DISTRIBUTION
CLK
INPUT
EPROM
–80
–100
Figure 14. Evaluation Board Platform
0
0.25
0.50
NORMALIZED FREQUENCY – Relative to fOUT
The evaluation board is designed to interface to a PC via a
National Instruments PCI-DIO-32HS digital IO card. A XILINX
FPGA formats the data between the AD987x and digital I/O
board. Software developed using National Instruments LabVIEW™
and provided as MS Windows™ executable programs is supplied
for the configuration of the SPI port registers and evaluation
of the AD9870 output data. These programs have a convenient
graphical user interface allowing for easy access to the various
SPI port configuration registers and real time frequency analysis
of output data.
Figure 13c. Folded Decimator Frequency Response
As Figure 13d shows, the gain variation across the passband
is approximately 0.4 dB. Normalization of full-scale is accurate
to within 0.4 dB across all decimation modes.
0
–20
–40
–60
–80
–100
0
0.25
NORMALIZED FREQUENCY – Relative to fOUT
Figure 13d. Passband Frequency Response of the
Decimator
–17–
REV. 0
AD9870
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
48-Lead LQFP
(ST-48)
0.063 (1.60)
MAX
0.354 (9.00) BSC SQ
0.030 (0.75)
0.018 (0.45)
37
48
36
1
0.276
(7.00)
BSC
SQ
TOP VIEW
(PINS DOWN)
COPLANARITY
0.003 (0.08)
25
12
0ꢈ
MIN
13
24
0.011 (0.27)
0.006 (0.17)
0.019 (0.5)
BSC
0.008 (0.2)
0.004 (0.09)
0.057 (1.45)
0.053 (1.35)
7ꢈ
0ꢈ
0.006 (0.15)
0.002 (0.05)
SEATING
PLANE
–18–
REV. 0
–19–
–20–
相关型号：
AD9874ABSTZRL
IC SPECIALTY TELECOM CIRCUIT, PQFP48, PLASTIC, MS-026BBC, LQFP-48, Telecom IC:Other
ADI
©2020 ICPDF网 联系我们和版权申明