AD9042SD/QMLV [ADI]
1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CDIP28, CERAMIC, DIP-28;型号: | AD9042SD/QMLV |
厂家: | ADI |
描述: | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CDIP28, CERAMIC, DIP-28 CD 转换器 |
文件: | 总24页 (文件大小:458K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
12-Bit, 41 MSPS
Monolithic ADC
AD9042
FEATURES
FUNCTIONAL BLOCK DIAGRAM
AV
DV
CC
CC
41 MSPS minimum sample rate
80 dB spurious-free dynamic range
595 mW power dissipation
A1
TH1
TH2
TH3
A2
AIN
ADC
V
OFFSET
Single 5 V supply
ADC
DAC
7
2.4V
V
AD9042
On-chip track-and-hold (T/H) and reference
Twos complement output format
CMOS-compatible output levels
REF
REFERENCE
6
ENCODE
ENCODE
DIGITAL ERROR CORRECTION LOGIC
INTERNAL
TIMING
MSB
LSB
APPLICATIONS
D11D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
GND
Cellular/PCS base stations
GPS anti jamming receivers
Communications receivers
Spectrum analyzers
Electro-optics
Figure 1.
Medical imaging
ATE
GENERAL DESCRIPTION
The AD9042 is a high speed, high performance, low power,
monolithic 12-bit analog-to-digital converter (ADC). All
necessary functions, including track-and-hold (T/H) and
reference, are included on chip to provide a complete conversion
solution. The AD9042 operates from a single 5 V supply and
provides CMOS-compatible digital outputs at 41 MSPS.
industrial grade is specified from −40°C to +85°C. However,
the AD9042 was designed to perform over the full military
temperature range (−55°C to +125°C); consult the factory for
military grade product options.
PRODUCT HIGHLIGHTS
1. Guaranteed sample rate is 41 MSPS.
Designed specifically to address the needs of wideband, multi-
channel receivers, the AD9042 maintains 80 dB spurious-free
dynamic range (SFDR) over a bandwidth of 20 MHz. Noise
performance is also exceptional; typical signal-to-noise ratio
(SNR) is 68 dB.
2. Dynamic performance specified over entire Nyquist band;
spurious signals 80 dBc typical for −1 dBFS input signals.
3. Low power dissipation: 595 mW off a single 5 V supply.
4. Reference and track-and-hold included on chip.
5. Packaged in 44-lead LQFP.
The AD9042 is built on a high speed complementary bipolar
process (XFCB) used by Analog Devices, Inc., and uses an
innovative multipass architecture. Units are packaged in a
44-lead LQFP low profile quad flat package. The AD9042
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©1995–2009 Analog Devices, Inc. All rights reserved.
AD9042
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 13
Encoding the AD9042 ............................................................... 13
Driving the Analog Input.......................................................... 14
Power Supplies............................................................................ 15
Output Loading .......................................................................... 15
Layout Information.................................................................... 15
Digital Wideband Receivers.......................................................... 16
Introduction................................................................................ 16
Noise Floor and SNR ................................................................. 18
Processing Gain.......................................................................... 18
Overcoming Static Nonlinearities with Dither ...................... 18
Receiver Example ....................................................................... 19
IF Sampling, Using the AD9042 as a Mix-Down Stage ........ 20
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
DC Specifications ......................................................................... 3
Switching Specifications .............................................................. 4
AC Specifications.......................................................................... 4
Absolute Maximum Ratings............................................................ 6
Thermal Resistance ...................................................................... 6
Explanation of Test Levels........................................................... 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 8
Terminology .................................................................................... 11
Equivalent Circuits......................................................................... 12
Receive Chain for Digital and Analog Beam Forming Medical
Ultrasound Using the AD9042........................................................ 21
Outline Dimensions....................................................................... 22
Ordering Guide .......................................................................... 22
REVISION HISTORY
9/09—Rev. A to Rev. B
5/96—Rev. 0 to Rev. A
Changes to Specifications Section...................................................2
Changes to Switching Specifications Section.................................2
Changes to AC Specifications Section............................................3
Changes to Ordering Guide.............................................................4
Changes to Pin Descriptions Section..............................................5
Added Die Layout and Mechanical Information Section ............6
Changes to Figure 2, Figure 3, Figure 5, and Figure 6..................7
Changes to Figure 37...................................................................... 14
Added Figure 38 ............................................................................. 15
Added Table 2 ................................................................................. 15
Added Figure 43, Figure 44, Figure 45, and Figure 46 .............. 17
Added Figure 47 and Figure 48 .................................................... 18
Changes to Figure 53...................................................................... 21
Changes to Figure 54...................................................................... 22
Added Receiver Example Section................................................. 22
Added Multitone Performance Section....................................... 22
Added Receive Chain for Digital Beam-Forming Medical
Ultrasound Using the AD9042 Section....................................... 23
Added Figure 58 ............................................................................. 23
Updated Format..................................................................Universal
Reorganized Layout............................................................Universal
Deleted DH-28 Package................................................ Throughout
Changes to General Description Section and Product
Highlights Section ............................................................................ 1
Deleted Wafer Test Limits Section ................................................. 4
Deleted Die Layout and Mechanical Information Table and Die
Layout with Pad Labels Figure........................................................ 6
Changes to Figure 4.......................................................................... 7
Deleted Figure 7; Renumbered Sequentially................................. 7
Deleted Figure 15 and Figure 16..................................................... 9
Deleted Evaluation Boards Section.............................................. 13
Changes to Layout Information Section...................................... 16
Removed Evaluation Boards Section........................................... 18
Changes to Figure 49 and Figure 50............................................. 19
Changes to Figure 52...................................................................... 20
Changes to Figure 54...................................................................... 22
Updated Outline Dimension......................................................... 24
Changes to Ordering Guide .......................................................... 24
10/95—Rev. 0: Initial Version
Rev. B | Page 2 of 24
AD9042
SPECIFICATIONS
DC SPECIFICATIONS
AVCC = DVCC = 5 V; VREF tied to VOFFSET through 50 Ω; TMIN = −40°C, TMAX = +85°C.
Table 1.
Parameter1
Temperature Test Level
Min
Typ
Max
Unit
RESOLUTION
12
Bits
DC ACCURACY
No Missing Codes
Offset Error
Offset Tempco
Gain Error
Full
Full
Full
Full
Full
25°C
VI
VI
V
VI
V
Guaranteed
−10
3
25
0
−50
2.4
+10
mV
ppm/°C
% FS
ppm/°C
V
−6.5
+6.5
Gain Tempco
2
REFERENCE OUT (VREF
ANALOG INPUT (AIN)
)
V
Input Voltage Range
Input Resistance
Input Capacitance
ENCODE INPUT3
Logic Compatibility4
VREF 0.500
250
5.5
V
Ω
pF
Full
25°C
IV
V
200
300
TTL/CMOS
Logic 1 Voltage
Logic 0 Voltage
Full
Full
Full
Full
25°C
VI
VI
VI
VI
V
2.0
0
450
−400
5.0
0.8
800
−200
V
V
μA
μA
pF
Logic 1 Current (VINH = 5 V)
Logic 0 Current (VINL = 0 V)
Input Capacitance
DIGITAL OUTPUTS
Logic Compatibility
Logic 1 Voltage (IOH = 10 μA)
625
−300
2
CMOS
4.2
25°C
Full
25°C
Full
I
IV
I
3.5
3.5
V
V
V
V
Logic 0 Voltage (IOL = 10 μA)
0.75
0.80
0.85
IV
Output Coding
Twos complement
POWER SUPPLY
AVCC Supply Voltage
AVCC Current (I)
DVCC Supply Voltage
DVCC Current (I)
ICC (Total) Supply Current
Power Dissipation
Power Supply Rejection Ratio (PSRR)
Full
Full
Full
Full
Full
Full
25°C
Full
VI
V
VI
V
VI
VI
I
5.0
109
5.0
10
119
595
1
V
mA
V
mA
mA
mW
mV/V
mV/V
147
735
+20
−20
V
5
1 C1 (Pin 10) tied to GND through a 0.01 μF capacitor.
2 VREF is normally tied to VOFFSET through 50 Ω. If VREF is used to provide dc offset to other circuits, it should first be buffered.
3
ENCODE
ENCODE driven by single-ended source;
bypassed to ground through a 0.01 μF capacitor.
ENCODE
4
ENCODE may also be driven differentially in conjunction with
; see the Encoding the AD9042 section for details.
Rev. B | Page 3 of 24
AD9042
SWITCHING SPECIFICATIONS
ENCODE
AVCC = DVCC = 5 V; ENCODE and
= 41 MSPS; VREF tied to VOFFSET through 50 Ω; TMIN = −40°C, TMAX = +85°C.
Table 2.
Parameter1
Temperature
Full
Full
25°C
25°C
25°C
25°C
Full
Test Level
Min
Typ
Max
Unit
MSPS
MSPS
ps
ps rms
ns
Maximum Conversion Rate
Minimum Conversion Rate
Aperture Delay (tA)
Aperture Uncertainty (Jitter)
ENCODE Pulse Width High
ENCODE Pulse Width Low
Output Delay (tOD)
VI
IV
V
41
5
−250
0.7
V
IV
IV
IV
10
10
5
ns
ns
9
14
1 C1 (Pin 10) tied to GND through a 0.01 μF capacitor.
AC SPECIFICATIONS
ENCODE
AVCC = DVCC = 5 V; ENCODE and
= 41 MSPS; VREF tied to VOFFSET through 50 Ω; TMIN = −40°C, TMAX = +85°C.
Table 3.
Parameter1, 2
SNR3
Temp
Test Level
Min
Typ
Max
Units
Analog Input at −1 dBFS
1.2 MHz
25°C
Full
25°C
Full
25°C
Full
V
V
V
V
I
68
dB
dB
dB
dB
dB
dB
67.5
67.5
67
67
66.5
9.6 MHz
19.5 MHz
64
V
SINAD4
Analog Input at −1 dBFS
1.2 MHz
25°C
Full
25°C
Full
V
V
V
V
I
67.5
67
67.5
67
dB
dB
dB
dB
dB
dB
9.6 MHz
19.5 MHz
25°C
Full
64
67
66.5
V
WORST SPUR5
Analog Input at −1 dBFS
1.2 MHz
25°C
Full
25°C
Full
25°C
Full
V
V
V
V
I
80
78
80
78
80
78
dBc
dBc
dBc
dBc
dBc
dBc
9.6 MHz
19.5 MHz
73
V
SMALL SIGNAL SFDR (WITH DITHER)6
Analog Input
1.2 MHz
9.6 MHz
19.5 MHz
Full
Full
Full
V
V
V
90
90
90
dBFS
dBFS
dBFS
TWO-TONE IMD REJECTION7
F1, F2 @ –7 dBFS
Full
Full
V
V
V
80
dBc
TWO-TONE SFDR (WITH DITHER)8
THERMAL NOISE
90
dBFS
25°C
0.33
LSB rms
Rev. B | Page 4 of 24
AD9042
Parameter1, 2
Temp
25°C
Full
Test Level
Min
Typ
0.3
0.4
Max
Units
LSB
LSB
DIFFERENTIAL NONLINEARITY
(ENCODE = 20 MSPS)
I
V
−1.0
+1.0
INTEGRAL NONLINEARITY
(ENCODE = 20 MSPS)
Full
V
V
V
V
0.75
LSB
MHz
ns
ANALOG INPUT BANDWIDTH
TRANSIENT RESPONSE
OVERVOLTAGE RECOVERY TIME
25°C
25°C
25°C
100
10
25
ns
1
ENCODE
All ac specifications tested by driving ENCODE and
differentially; see the Encoding the AD9042 section for details.
2 C1 (Pin 10 on AD9042ASTZ only) tied to GND through a 0.01 μF capacitor.
3 Analog input signal power at −1 dBFS; signal-to-noise ratio (SNR) is the ratio of signal level to total noise (first five harmonics removed).
4 Analog input signal power at −1 dBFS; signal-to-noise and distortion (SINAD) is the ratio of signal level to total noise + harmonics.
5 Analog input signal power at −1 dBFS; worst spur is the ratio of the signal level to worst spur, usually limited by harmonics.
6 Analog input signal power swept from −20 dBFS to –95 dBFS; dither power = −32.5 dBm; dither circuit used on input signal (see the Overcoming Static Nonlinearities
with Dither section); SFDR is the ratio of converter full scale to worst spur.
7 Tones at −7 dBFS (f1 = 15.3 MHz, f2 = 19.5 MHz); two-tone intermodulation distortion (IMD) rejection is ratio of either tone to worst-third order intermodulation
product.
8 Both input tones swept from −20 dBFS to −95 dBFS; dither power = −32.5 dBm; dither circuit used on input signal (see the Overcoming Static Nonlinearities with
Dither section); two-tone spurious-free dynamic range (SFDR) is the ratio of converter full scale to worst spur.
Rev. B | Page 5 of 24
AD9042
ABSOLUTE MAXIMUM RATINGS
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 4.
Parameter1
Rating
AVCC Voltage
0 V to 7 V
DVCC Voltage
0 V to 7 V
Analog Input Voltage
Analog Input Current
0.5 V to 4.5 V
20 mA
Digital Input Voltage (ENCODE)
ENCODE, ENCODE Differential Voltage
Digital Output Current
Operating Temperature Range (Ambient)
Maximum Junction Temperature
Lead Temperature (Soldering, 10 sec)
Storage Temperature Range (Ambient)
0 V to AVCC
4 V
−40 to +40 mA
−40 °C to +85°C
+150°C
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 5. Thermal Resistance
+300°C
−65°C to +150°C
Package Type
θJA
Unit
44-Lead LQFP
55
°C/W
1Absolute maximum ratings are limiting values to be applied individually, and
beyond which the serviceability of the circuit may be impaired.
EXPLANATION OF TEST LEVELS
I.
100% production tested.
II.
100% production tested at +25°C, and sample tested at
specified temperatures. AC testing done on sample basis.
III.
IV.
Sample tested only.
Parameter is guaranteed by design and characterization
testing.
V.
Parameter is a typical value only.
VI.
100% production tested at +25°C; sample tested at
temperature extremes.
ESD CAUTION
Rev. B | Page 6 of 24
AD9042
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
44 43 42 41 40 39 38 37 36 35 34
1
33
32
31
30
29
28
27
26
25
24
23
DV
DV
D8
CC
CC
PIN 1
2
3
D7
ENCODE
ENCODE
GND
D6
4
D5
5
D4
AD9042
6
GND
D3
TOP VIEW
(Not to Scale)
7
AIN
D2
8
V
D1
OFFSET
9
V
D0 (LSB)
GND
NC
REF
C1
10
11
AV
CC
12 13 14 15 16 17 18 19 20 21 22
NC = NO CONNECT
Figure 2. Pin Configuration
Table 6. Pin Function Descriptions
Pin No. Mnemonic Description
1, 2
3
4
DVCC
5 V Power Supply (Digital). Powers output stage only.
Encode Input. Data conversion initiated on rising edge.
Complement of ENCODE. Drive differentially with ENCODE or bypass to ground for single-ended clock mode.
ENCODE
ENCODE
GND
5, 6
7
Ground.
AIN
Analog Input.
8
9
VOFFSET
VREF
Voltage Offset Input. Sets mid point of analog input range. Normally tied to VREF through a 50 Ω resistor.
Internal Voltage Reference. Nominally 2.4 V; normally tied to VOFFSET through a 50 Ω resistor. Bypass to ground
and with 0.1 μF + 0.01 μF microwave chip capacitor.
10
C1
Internal Bias Point. Bypass to ground with a 0.01 μF capacitor.
11, 12
13, 14
15, 16
17, 18
19, 20
21, 22
23
AVCC
GND
AVCC
GND
AVCC
GND
NC
5 V Power Supply (Analog).
Ground.
5 V Power Supply (Analog).
Ground.
5 V Power Supply (Analog).
Ground.
No Connect
24
25
GND
D0 (LSB)
Ground.
Digital Output Bit (Least Significant Bit).
26 to 33 D1 to D8
Digital Output Bits.
34, 35
36, 37
38, 39
40, 41
42, 43
44
GND
DVCC
GND
DVCC
D9 to D10
D11 (MSB)
Ground.
5 V Power Supply (Digital). Powers output stage only.
Ground.
5 V Power Supply (Digital). Powers output stage only.
Digital Output Bits.
Digital Output Bit (Most Significant Bit). Output coded as twos complement.
Rev. B | Page 7 of 24
AD9042
TYPICAL PERFORMANCE CHARACTERISTICS
0
ENCODE = 41MSPS
ENCODE = 41MSPS
81
80
79
78
77
AIN = 1.2MHz
TEMP = –40°C, +25°C, AND +85°C
T = +25°C
–20
–40
–60
T = –40°C
T = +85°C
2
3
4
5
6
7
8
9
–80
–100
–120
0
2
4
6
8
10
12
14
16
18
20
dc
4.1
8.2
12.3
16.4
20.5
ANALOG INPUT FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 3. Single Tone at 1.2 MHz
Figure 6. Worst-Case Harmonics vs. AIN
0
–20
ENCODE = 41MSPS
ENCODE = 41MSPS
AIN = 9.6MHz
70
69
68
67
66
TEMP = –40°C, +25°C, AND +85°C
–40
T = –40°C
–60
4
8 8
5
3
7
6
2
T = +25°C
–80
T = +85°C
–100
–120
0
2
4
6
8
10
12
14
16
18
20
dc
4.1
8.2
12.3
16.4
20.5
ANALOG INPUT FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 4. Single Tone at 9.6 MHz
Figure 7. SNR vs. AIN
0
–20
90
ENCODE = 41MSPS
ENCODE = 41MSPS
AIN = 19.5MHz
80
70
60
50
40
30
–40
–60
2
4
6
8
9
7
5
3
–80
–100
–120
1
2
4
10
20
40
100
dc
4.1
8.2
12.3
16.4
20.5
ANALOG INPUT FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 8. Worst-Case Harmonics vs. AIN
Figure 5. Single Tone at 19.5 MHz
Rev. B | Page 8 of 24
AD9042
0
–20
0
–20
ENCODE = 41MSPS
AIN = BROADBAND_NOISE
ENCODE = 41MSPS
AIN = 15.3MHz, 19.5MHz
–40
–40
–60
–60
4
–80
–80
–100
–100
–120
–120
dc
4.1
8.2
12.3
16.4
20.5
dc
4.1
8.2
12.3
16.4
20.5
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 12. NPR Output Spectrum
Figure 9. Two Tones at 15.3 MHz and 19.5 MHz
0
–20
85
AIN = 4.3MHz
WORST SPUR
ENCODE = 41MSPS
AIN = 19.5MHz @ –29dBFS
NO DITHER
80
75
70
65
60
–40
–60
2
4
6
8
8
7
5
3
SNR
–80
–100
–120
dc
4.1
8.2
12.3
16.4
20.5
dc
5
10
15
20
25
30
35
40
45
50
FREQUENCY (MHz)
SAMPLE RATE (MSPS)
Figure 10. SNR, Worst Harmonic vs. Encode
Figure 13. 4K FFT Without Dither
90
85
80
75
70
65
60
55
50
45
40
35
30
100
90
80
70
60
50
40
30
20
10
0
ENCODE = 41MSPS
AIN = 19.5MHz
ENCODE = 41MSPS
AIN = 19.5MHz
NO DITHER
WORST SPUR
SNR
SFDR = 80dB
REFERENCE LINE
25
30
35
40
45
50
55
60
65
70
75
–80
–70
–60
–50
–40
–30
–20
–10
0
ENCODE DUTY CYCLE (%)
ANALOG INPUT POWER LEVEL (dBFS)
Figure 11. SNR, Worst Spurious vs. Duty Cycle
Figure 14. SFDR Without Dither
Rev. B | Page 9 of 24
AD9042
0
100
90
80
70
60
50
40
30
20
10
0
ENCODE = 41MSPS
AIN = 2.5MHz @ –26dBFS
NO DITHER
ENCODE = 41MSPS
AIN = 19.5MHz
–20
DITHER = –32.5dBm
–40
–60
–80
–100
SFDR = 80dB
REFERENCE LINE
–120
dc
–80
–70
–60
–50
–40
–30
–20
–10
0
4.1
8.2
12.3
16.4
20.5
FREQUENCY (MHz)
ANALOG INPUT POWER LEVEL (dBFS)
Figure 15. 128K FFT Without Dither
Figure 17. SFDR with Dither
0
–20
0
–20
ENCODE = 41MSPS
ENCODE = 41MSPS
AIN = 2.5MHz @ –26dBFS
DITHER = –32.5dBm
AIN = 19.5MHz @ –29dBFS
DITHER = –32.5dBm
–40
–40
–60
–60
2
4
6
8
8
7
5
3
–80
–80
–100
–100
–120
–120
dc
4.1
8.2
12.3
16.4
20.5
dc
4.1
8.2
12.3
16.4
20.5
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 16. 4K FFT with Dither
Figure 18. 128K FFT with Dither
Rev. B | Page 10 of 24
AD9042
TERMINOLOGY
Signal-to-Noise Ratio SNR (Without Harmonics)
Analog Bandwidth
The ratio of the rms signal amplitude (set at 1 dB below full
scale) to the rms value of the sum of all other spectral
components, excluding the first five harmonics and dc.
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Spurious-Free Dynamic Range (SFDR)
Aperture Delay
The ratio of the rms signal amplitude to the rms value of the
peak spurious spectral component. The peak spurious
component may or may not be a harmonic. May be reported in
decibels (degrades as signal levels is lowered) or in decibels
relative to full scale (always related back to converter full scale).
The delay between the 50% point of the rising edge of the
ENCODE command and the instant at which the analog input
is sampled.
Aperture Uncertainty (Jitter)
The sample-to-sample variation in aperture delay.
Transient Response
Differential Nonlinearity (DNL)
The deviation of any code from an ideal 1 LSB step.
The time required for the converter to achieve 0.02% accuracy
when a one-half full-scale step function is applied to the
analog input.
Encode Pulse Width/Duty Cycle
Pulse width high is the minimum amount of time that the
ENCODE pulse should be left in a Logic 1 state to achieve the
rated performance; pulse width low is the minimum time that
the ENCODE pulse should be left in low state. At a given clock
rate, these specifications define an acceptable encode duty cycle.
Two-Tone Intermodulation Distortion Rejection
The ratio of the rms value of either input tone to the rms value
of the worst third-order intermodulation product; reported in dBc.
Two-Tone SFDR
The ratio of the rms value of either input tone to the rms value
of the peak spurious component. The peak spurious component
may or may not be an IMD product. May be reported in dBc
(degrades as signal level is lowered) or in dBFS (always related
back to converter full scale).
Harmonic Distortion
The ratio of the rms signal amplitude to the rms value of the
worst harmonic component, reported in dBc.
Integral Nonlinearity (INL)
The deviation of the transfer function from a reference line
measured in fractions of 1 LSB using a best straight line
determined by a least square curve fit.
Maximum Conversion Rate
The encode rate at which parametric testing is performed.
Minimum Conversion Rate
The encode rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed limit.
Output Propagation Delay
The delay between the 50% point of the rising edge of the
ENCODE command and the time when all output data bits
are within valid logic levels.
Overvoltage Recovery Time
The amount of time required for the converter to recover to
0.02% accuracy after an analog input signal 150% of full scale is
reduced to midscale.
Power Supply Rejection Ratio (PSRR)
The ratio of a change in input offset voltage to a change in
power supply voltage.
Signal-to-Noise-and-Distortion (SINAD) Ratio
The ratio of the rms signal amplitude (set at 1 dB below full
scale) to the rms value of the sum of all other spectral
components, including harmonics but excluding dc.
Rev. B | Page 11 of 24
AD9042
EQUIVALENT CIRCUITS
N
tA = –250 ps TYP
ANALOG
INPUT
(AIN)
N + 1
ENCODE
INPUTS
(ENCODE)
DIGITAL
OUTPUTS
(D11 TO D0)
N
N – 2
N – 1
tOD = 9ns TYP
Figure 19. Timing Diagram
AV
CC
DV
CC
3.5V
CURRENT
MIRROR
AV
CC
250µA
250Ω
250Ω
AIN
AV
V
CC
DV
OFFSET
CC
250µA
V
REF
200Ω
D0 TO D11
1.5V
6pF
Figure 20. Analog Input Stage
AV
CC
CURRENT
MIRROR
AV
AV
CC
CC
17kΩ
R1
R1
17kΩ
Figure 23. Digital Output Stage
ENCODE
ENCODE
AV
CC
TIMING
CIRCUITS
R2
8kΩ
R2
8kΩ
AV
CC
2.4V
V
REF
Figure 21. Encode Inputs
0.5mA
AV
CC
Figure 24. 2.4 V Reference
V
REF
AV
CC
AV
CC
CURRENT
MIRROR
C1
(PIN 10)
Figure 22. Compensation Pin, C1
Rev. B | Page 12 of 24
AD9042
THEORY OF OPERATION
The AD9042 analog-to-digital converter (ADC) employs a two-
stage subrange architecture. This design approach ensures
12-bit accuracy, without the need for laser trim, at low power.
5V
ENCODE
SOURCE
ENCODE
ENCODE
R1
R2
V
L
0.01µF
R
As shown in Figure 1, the 1 V p-p single-ended analog input,
centered at 2.4 V, drives a single-input to differential-output
amplifier, A1. The output of A1 drives the first track-and-hold,
TH1. The high state of the ENCODE pulse places TH1 in hold
mode. The held value of TH1 is applied to the input of the 6-bit
coarse ADC. The digital output of the coarse ADC drives a 6-bit
DAC; the DAC is 12 bits accurate. The output of the 6-bit DAC
is subtracted from the delayed analog signal at the input to TH3
to generate a residue signal. TH2 is used as an analog pipeline
to null out the digital delay of the coarse ADC.
X
AD9042
Figure 26. Lower Logic Threshold for Encode
To raise the logic threshold, use the following equation:
5R2
V1 =
R1RX
R2 +
R1 + RX
AV
CC
The residue signal is passed to TH3 on a subsequent clock cycle
where the signal is amplified by the residue amplifier, A2, and
converted to a digital word by the 7-bit residue ADC. One bit of
overlap is used to accommodate any linearity errors in the
coarse ADC.
R
X
5V
ENCODE
SOURCE
ENCODE
ENCODE
R1
R2
V
L
0.01µF
AD9042
The 6-bit coarse ADC word and 7-bit residue word are added
together and corrected in the digital error correction logic to
generate the output word. The result is a 12-bit parallel digital
word, which is CMOS-compatible, coded as twos complement.
Figure 27. Raise Logic Threshold for Encode
Although the single-ended encode works well for many
applications, driving the encode differentially provides increased
performance. Depending on circuit layout and system noise, a
1 dB to 3 dB improvement in SNR can be realized. It is not
recommended that differential TTL logic be used, however,
because most TTL families that support complementary
outputs are not delay or slew rate matched. Instead, it is
recommended that the encode signal be ac-coupled into the
ENCODING THE AD9042
The AD9042 is designed to interface with TTL and CMOS logic
families. The source used to drive the ENCODE pin(s) must be
clean and free from jitter. Sources with excessive jitter limit SNR
(see Equation 1 in the Noise Floor and SNR section).
AD9042
ENCODE
ENCODE and
pins.
TTL OR CMOS
ENCODE
SOURCE
The simplest option is shown in Figure 28. The low jitter TTL
signal is coupled with a limiting resistor, typically 100 Ω, to the
primary side of an RF transformer (these transformers are
inexpensive and readily available; part number in Figure 28 is
from Mini-Circuits). The secondary side is connected to the
ENCODE
0.01µF
Figure 25. Single-Ended TTL/CMOS Encode
ENCODE
The AD9042 encode inputs are connected to a differential input
stage (see Figure 21 in the Equivalent Circuits section). With no
input connected to either the ENCODE or input, the voltage
dividers bias the inputs to 1.6 V. For TTL or CMOS usage, the
ENCODE and
pins of the converter. Because both
encode inputs are self-biased, no additional components are
required.
100Ω
T1-1T
ENCODE
ENCODE
ENCODE
encode source should be connected to ENCODE.
TTL
should be decoupled using a low inductance or microwave chip
capacitor to ground. Devices such as the AVX 05085C103MA15, a
0.01 μF capacitor, work well.
AD9042
Figure 28. TTL Source Differential Encode
If a logic threshold other than the nominal 1.6 V is required, the
following equations show how to use an external resistor, Rx, to
raise or lower the trip point (see Figure 21; R1 = 17 kΩ, R2 = 8 kΩ).
To lower the logic threshold, use the following equation:
5R2 RX
V1 =
R1R2 + R1RX + R2 RX
Rev. B | Page 13 of 24
AD9042
If no TTL source is available, a clean sine wave can be substituted.
In the case of the sine source, the matching network is shown in
Figure 29. Because the matching transformer specified is a 1:1
impedance ratio, R, the load resistor should be selected to
match the source impedance. The input impedance of the
AD9042 is negligible in most cases.
250Ω
250Ω
–
AIN
+
V
OFFSET
TIED TO
V
THROUGH
50Ω
REF
2.4V
REFERENCE
AD9042
50Ω
0.1µF
T1-1T
SINE
SOURCE
ENCODE
Figure 32. Analog Input Offset by 2.4 V Reference
R
AD9042
Although the AD9042 can be used in many applications, it was
specifically designed for communications systems that must
digitize wide signal bandwidths. As such, the analog input was
designed to be ac-coupled. Because most communications
products do not downconvert to dc, this should not pose a
problem. One example of a typical analog input circuit is shown
in Figure 33. In this application, the analog input is coupled
with a high quality chip capacitor, the value of which can be
chosen to provide a low frequency cutoff that is consistent with
the signal being sampled; in most cases, a 0.1 μF chip capacitor
works well.
ENCODE
Figure 29. Sine Source Differential Encode
If a low jitter ECL clock is available, another option is to ac-
couple a differential ECL signal to the encode input pins as
shown in Figure 30. The capacitors shown here should be chip
capacitors but do not need to be of the low inductance variety.
0.1µF
ENCODE
ECL
0.1µF
GATE
AD9042
ENCODE
510Ω
510Ω
AD9042
0.1µF
ANALOG
AIN
SIGNAL
SOURCE
–V
R
S
T
V
OFFSET
REF
Figure 30. Differential ECL for Encode
50Ω
V
As a final alternative, the ECL gate can be replaced by an ECL
comparator. The input to the comparator could then be a logic
signal or a sine signal.
0.1µF
Figure 33. AC-Coupled Analog Input Signal
AD96687 (1/2)
0.1µF
Another option for ac coupling is a transformer. The impedance
ratio and frequency characteristics of the transformer are
determined by examining the characteristics of the input signal
source (transformer primary connection), and the AD9042
input characteristics (transformer secondary connection).
Given the transformer turns ratio, RT should be chosen to
satisfy the termination requirements of the source. A blocking
capacitor is required to prevent AD9042 dc bias currents from
flowing through the transformer.
+
–
ENCODE
ENCODE
0.1µF
50Ω
AD9042
510Ω
510Ω
–V
S
Figure 31. ECL Comparator for Encode
Care should be taken not to overdrive the encode input pins
when ac-coupled. Although the input circuitry is electrically
protected from overvoltage or undervoltage conditions,
improper circuit operations may result from overdriving the
encode input pins.
AD9042
0.1µF
ANALOG
SIGNAL
SOURCE
XFMR
AIN
BPF
R
T
V
OFFSET
50Ω
DRIVING THE ANALOG INPUT
V
REF
LO
0.1µF
Because the AD9042 operates from a single 5 V supply, the
analog input range is offset from ground by 2.4 V. The analog input,
AIN, is an operational amplifier configured in an inverting mode
(see Figure 32). VOFFSET is the noninverting input, which is
normally tied through a 50 Ω resistor to VREF (see Figure 32).
Because the operational amplifier forces its inputs to the same
voltage, the inverting input is also at 2.4 V. Therefore, the analog
input has a Thevenin equivalent of 250 Ω in series with a 2.4 V
source. It is strongly recommended that the internal voltage
reference of the AD9042 be used for the amplifier offset; this
reference is designed to track internal circuit shifts over
temperature.
Figure 34. Transformer-Coupled Analog Input Signal
Rev. B | Page 14 of 24
AD9042
When calculating the proper termination resistor, note that the
external load resistor is in parallel with the AD9042 analog
input resistance, 250 Ω. The external resistor value can be
calculated from the following equation:
OUTPUT LOADING
Care must be taken when designing the data receivers for the
AD9042. It is recommended that the digital outputs drive a
series resistor of 499 Ω followed by a CMOS gate such as the
74AC574. To minimize capacitive loading, there should be only
one gate on each output pin. The digital outputs of the AD9042
have a unique constant slew rate output stage. The output slew
rate is about 1 V/ns independent of output loading. A typical
CMOS gate combined with PCB trace and through hole has a
load of approximately 10 pF. Therefore, as each bit switches, 10 mA
of dynamic current per bit flows in or out of the device. A full-
scale transition can cause up to 120 mA (12 bits × 10 mA/bit) of
current to flow through the digital output stage. The series
resistor minimizes the output currents that can flow in the
output stage. These switching currents are confined between
ground and the DVCC pin. Standard TTL gates should be
avoided because they can appreciably add to the dynamic
switching currents of the AD9042.
1
RT
=
1
Z
1
−
250
where Z is desired impedance.
A dc-coupled input configuration (shown in Figure 35) is
limited by the drive amplifier performance. The on-chip
reference of the AD9042 is buffered using the OP279 dual, rail-
to-rail operational amplifier. The resulting voltage is combined
with the analog source using an AD9631. Pending improvements
in drive amplifiers, this dc-coupled approach is limited to ~75 dB
to 80 dB of dynamic performance depending on which drive
amplifier is used. The AD9631 and OP279 run off 5 V.
AD9631
21Ω
79Ω
AD9042
AIN
SIGNAL
SOURCE
50Ω
200Ω
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
1V
0pF
TO
50pF
10 pF ×
114Ω
0.1µF
1 ns
V
V
OFFSET
1kΩ
49.9Ω
LAYOUT INFORMATION
571Ω
REF
0.1µF
The pinout of the AD9042 facilitates ease of use and the
implementation of high frequency/high resolution design
practices. All of the digital outputs are on one side of the
package, and all of the inputs are on the other sides of the
package. It is highly recommended that high quality ceramic
chip capacitors be used to decouple each supply pin to ground
directly at the device. Depending on the configuration used for
the encode and analog inputs, one or more capacitors are
required on those input pins. The capacitors used on the
OP279
(1/2)
OP279
(1/2)
Figure 35. DC-Coupled Analog Input Circuit
POWER SUPPLIES
Care should be taken when selecting a power source. Linear
supplies are strongly recommended because switching supplies
tend to have radiated components that may be received by the
AD9042. Each of the power supply pins should be decoupled as
close to the package as possible using 0.1 μF chip capacitors.
ENCODE
and VREF pins must be low inductance chip capacitors
as noted previously.
The AD9042 has separate digital and analog 5 V pins. The AVCC
pins are the analog supply pins, and the DVCC pins are the
digital supply pins. Although analog and digital supplies may
be tied together, best performance is achieved when the supplies
are separate. This is because the fast digital output swings can
couple switching noise back into the analog supplies. Note that
AVCC must be held within 5% of 5 V.
Although a multilayer board is recommended, it is not required
to achieve good results. Care should be taken when placing the
digital output runs. Because the digital outputs have such a high
slew rate, the capacitive loading on the digital outputs should be
minimized. Circuit traces for the digital outputs should be kept
short and connected directly to the receiving gate (broken only
by the insertion of the series resistor). Logic fanout for each bit
should be one CMOS gate.
Rev. B | Page 15 of 24
AD9042
DIGITAL WIDEBAND RECEIVERS
First, many passive discrete components that formed the tuning
and filtering functions have been eliminated. These passive
components often require adjusting and special handling
during assembly and final system alignment. Digital
INTRODUCTION
Several key technologies are now being introduced that may
forever alter the vision of radio. Figure 36 shows the typical dual
conversion superheterodyne receiver. The signal picked up by
the antenna is mixed down to an intermediate frequency (IF)
using a mixer with a variable local oscillator (LO); the variable
LO is used to tune in the desired signal. This first IF is mixed
down to a second IF using another mixer stage and a fixed LO.
Demodulation takes place at the second or third IF using either
analog or digital techniques.
components require no such adjustments; tuner and filter
characteristics are always exactly the same. Moreover, the
tuning and filtering characteristics can be changed through
software. Because software is used for demodulation, different
routines may be used to demodulate different standards such as
AM, FM, GMSK, or any other desired standard. In addition, as
new standards arise or new software revisions are generated,
they may be field installed with standard software update
channels. A radio that performs demodulation in software as
opposed to hardware is often referred to as a soft radio because
it can be changed or modified simply through code revision.
ADCs
NARROW-BAND NARROW-BAND
FILTER
FILTER
LNA
I
Q
IF
IF
2
1
RF
900MHz
System Description
FIXED
VARIABLE
In the wideband digital radio (see Figure 37), the first down-
conversion functions in much the same way as a block converter
does. An entire band is shifted in frequency to the desired
intermediate frequency. In the case of cellular base station
receivers, 5 MHz to 20 MHz of bandwidth are downconverted
simultaneously to an IF frequency suitable for digitizing with a
wideband ADC. Once digitized, the broadband digital data
stream contains all of the in-band signals. The remainder of the
radio is constructed digitally using special-purpose and general-
purpose programmable DSP to perform filtering, demodulation,
and signal conditioning, not unlike the analog counterparts.
SHARED
ONE RECEIVER PER CHANNEL
Figure 36. Narrow-Band Digital Receiver Architecture
If demodulation takes place in the analog domain, then traditional
discriminators, envelope detectors, phase-locked loops, or other
synchronous detectors are generally used to strip the modulation
from the selected carrier.
However, as general-purpose DSP chips such as the ADSP-2181
become more popular, they can be used in many baseband
sampled application such as the one shown in Figure 36. As
shown in the figure, prior to ADC conversion, the signal must be
mixed down and filtered, and the I and Q components must be
separated. These functions are realized through DSP techniques;
however, several key technology breakthroughs are required:
high dynamic range ADCs, such as the AD9042, new DSPs
(highly programmable with fast onboard memory), digital
tuner and filter (with programmable frequency and BW), and
wideband mixers (high dynamic range with >12.5 MHz BW).
WIDEBAND
In the narrow-band receiver (see Figure 36), the signal to be
received must be tuned. This is accomplished by using a
variable local oscillator at the first mix-down stage. The first IF
then uses a narrow-band filter to reject out-of-band signals and
condition the selected carrier for signal demodulation.
In the digital wideband receiver (see Figure 37), the variable
local oscillator has been replaced with a fixed oscillator, so
tuning must be accomplished in another manner. Tuning is
performed digitally using a digital downconversion and a filter
chip frequently called a channelizer. The term, channelizer, is
used because the purpose of these chips is to select one channel
out of the many within the broadband of spectrum actually
present in the digital data stream of the ADC.
ADC
WIDEBAND
FILTER
WIDEBAND
MIXER
LNA
"n" CHANNELS
TO DSP
RF
900MHz
12.5MHz
(416 CHANNELS)
FIXED
SHARED
CHANNEL SELECTION
DECIMATION
FILTER
LOW-PASS
FILTER
I
Figure 37. Wideband Digital Receiver Architecture
COS
Figure 37 shows such a wideband system. This design shows
that the front-end variable local oscillator has been replaced
with a fixed oscillator (for single-band radios), and the back end
has been replaced with a wide dynamic range ADC, digital
tuner, and DSP. This technique offers many benefits.
DIGITAL
TUNER
DATA
SIN
DECIMATION
FILTER
LOW-PASS
FILTER
Q
Figure 38. Digital Channelizer
Rev. B | Page 16 of 24
AD9042
Figure 38 shows the block diagram of a typical channelizer.
Channelizers consist of a complex NCO (numerically controlled
oscillator), dual multiplier (mixer), and matched digital filters.
These are the same functions that would be required in an
analog receiver but implemented in digital form. The digital
output from the channelizer is the desired carrier, frequently in
I and Q format; all other signals are filtered and removed based
on the filtering characteristics desired. Because the channelizer
output consists of one selected RF channel, one tuner chip is
required for each frequency received, although only one
wideband RF receiver is needed for the entire band. Data from
the channelizer can then be processed using a digital signal
processor such as the ADSP-2181 or the SHARC ADSP-21062
processor. This data may then be processed through software to
demodulate the information from the carrier.
bipolar device, power dissipation is not a function of sample
rate. Thus, there is no penalty paid in power by operating at
faster sample rates. By carefully selecting input frequency range
and sample rate, the drive amplifier and ADC harmonics can
actually be placed out-of-band. Thus, other components such as
filters and IF amplifiers may actually end up being the limiting
factor on dynamic range.
For example, if the system has second and third harmonics that
are unacceptably high, the careful selection of the encode rate
and signal bandwidth can place these second and third harmonics
out-of-band. For the case of an encode rate equal to 40.96 MSPS
and a signal bandwidth of 5.12 MHz, placing the fundamental
at 5.12 MHz places the second and third harmonics out-of-
band as shown in Table 7.
Table 7. Example Frequency Plan
Figure 39 shows a typical wideband receiver subsystem based
around the AD9042. This strip consists of a wideband IF filter,
amplifier, ADC, latches, channelizer, and interface to a digital
signal processor. This design shows a typical clocking scheme
used in many receiver designs. All timing within the system is
referenced back to a single clock. Although this is not necessary,
it facilitates PLL design, ease of manufacturing, system test, and
calibration. Keeping in mind that the overall performance goal
is to maintain the best possible dynamic range, many choices
must be considered.
Parameter
Value
Encode Rate
40.96 MSPS
Fundamental
Second Harmonic
Third Harmonic
5.12 MHz to 10.24 MHz
10.24 MHz to 20.48 MHz
15.36 MHz to 10.24 MHz
Another option is found through band-pass sampling. If the
analog input signal range is from dc to FS/2, then the amplifier
and filter combination must perform to the specification required.
However, if the signal is placed in the third Nyquist zone (FS to
3 FS/2), the amplifier is no longer required to meet the harmonic
performance required by the system specifications because all
harmonics fall outside the pass-band filter. For example, the
pass-band filter ranges from fS to 3 FS/2. The second harmonic
would span from 2 FS to 3 FS, well outside the range of the
pass-band filter. The burden then is placed on the filter design,
provided that the ADC meets the basic specifications at the
frequency of interest. In many applications, this is a worthwhile
trade-off because many complex filters can easily be realized
using SAW and LCR techniques alike at these relatively high IF
frequencies. Although the harmonic performance of the drive
amplifier is relaxed by this technique, intermodulation
One of the biggest challenges is selecting the amplifier used to
drive the AD9042. Because this is a communications application,
the key specification for this amplifier is spurious-free dynamic
range (SFDR). An amplifier should be selected that can provide
SFDR performance better than 80 dB into 250 Ω. One such
amplifier is the AD9631. These low spurious levels are necessary
because harmonics due to the drive amplifier and ADC can
distort the desired signals of interest.
Two other key considerations for the digital wideband receiver
are converter sample rate and IF frequency range. Because
performance of the AD9042 converter is nearly independent
of both sample rate and analog input frequency (see Figure 6,
Figure 7, and Figure 10), the designer has greater flexibility in the
selection of these parameters. Also, because the AD9042 is a
performance cannot be sacrificed because intermods must be
assumed to fall in-band for both amplifiers and converters.
5V (A)
5V (D)
499Ω
CMOS
BUFFER
CHANNELIZER
ADSP-2181
5MHz TO 15MHz
PASS BAND
PRESELECT
FILTER
LNA
D11
AIN
I AND Q
DATA
LO
12
NETWORK
CONTROLLER
INTERFACE
DRIVE
AD9042
864MHz
ENCODE
ENCODE
M/N PLL
SYNTHESIZER
REF
IN
CLK
D0
40.96MHz
REFERENCE
CLOCK
Figure 39. Simplified 5 MHz Wideband “A” Carrier Receiver
Rev. B | Page 17 of 24
AD9042
that traditionally has been provided by the ceramic or crystal
filters of a narrow-band receiver. This narrow-band filtering is
the source of the processing gain associated with a wideband
receiver and is simply the ratio of the pass-band to whole band
expressed in dBc. For example, if a 30 kHz AMPS signal is
digitized with an AD9042 sampling at 40.96 MSPS, the ratio is
0.030 MHz/20.48 MHz. Expressed in log form, the processing
gain is −10 × log (0.030 MHz/20.48 MHz) or 28.3 dB.
NOISE FLOOR AND SNR
Oversampling is the act of sampling at a rate that is greater than
twice the bandwidth of the signal desired. Oversampling has
nothing to do with the actual frequency of the sampled signal. It is
the bandwidth of the signal that is key. Band-pass or IF sampling
refers to sampling a frequency that is higher than Nyquist and
often provides additional benefits such as downconversion
using the ADC and track-and-hold as a mixer. Oversampling
leads to processing gains because the faster the signal is digitized,
the wider the distribution of noise. Because the integrated noise
must remain constant, the actual noise floor is lowered by 3 dB
each time the sample rate is doubled. The effective noise density
for an ADC may be calculated by the following equation:
Additional filtering and noise reduction techniques can be
achieved through DSP techniques; many applications obtain
additional process gains through proprietary noise reduction
algorithms.
OVERCOMING STATIC NONLINEARITIES WITH
DITHER
10−SNR / 20
V
NOISE rms / Hz =
4 FS
Typically, high resolution data converters use multistage techniques
to achieve high bit resolution without large comparator arrays
that would be required if traditional flash ADC techniques were
used. The multistage converter typically provides better wafer
yields, meaning lower cost and much lower power. However,
because it is a multistage device, certain portions of the circuit
are used repetitively as the analog input sweeps from one end of
the converter range to the other. Although the worst DNL error
may be less than 1 LSB, the repetitive nature of the transfer
function can create havoc with low level dynamic signals. Spurious
signals for a full-scale input may be −88 dBc; however, at 29 dB
below full scale, these repetitive DNL errors can cause SFDR to
fall to 80 dBc as shown in Figure 13.
For a typical SNR of 68 dB and a sample rate of 40.96 MSPS, this is
equivalent to 31 nV/√Hz . This equation shows the relationship
between the SNR of the converter and the sample rate FS. This
equation can be used todetermine overall receiver noise.
The SNR for an ADC can be predicted. When normalized to
ADC codes, the following equation accurately predicts the SNR
based on three terms. These are jitter, average DNL error, and
thermal noise. Each of these terms contributes to the noise
within the converter.
1/2
2
2
⎡
⎢
⎤
⎥
⎛VNOISErms
⎞
⎟
⎟
⎠
1+ ε
212
⎛
⎜
⎞
2
⎜
SNR= −20log
(
2 πFANALOG×tJ rms
)
+
+
⎟
⎠
212
⎜
⎢
⎥
⎦
⎝
⎝
A common technique for randomizing and reducing the effects
of repetitive static linearity is through the use of dither. The
purpose of dither is to force the repetitive nature of static linearity
to appear as if it were random. Then, the average linearity over
the range of dither dominates the SFDR performance. In the
AD9042, the repetitive cycle is every 15.625 mV p-p.
⎣
where
F
t
ANALOG is analog input frequency.
J rms is rms jitter of the encode (rms sum of encode source and
internal encode circuitry).
To ensure adequate randomization, 5.3 mV rms is required; this
equates to a total dither power of −32.5 dBm. This randomizes
the DNL errors over the complete range of the residue converter.
Although lower levels of dither such as that from previous
analog stages reduces some of the linearity errors, the full effect
is gained only with this larger dither. Increasing dither even
more can be used to reduce some of the global INL errors.
However, signals much larger than the microvolts proposed in
this data sheet begin to reduce the usable dynamic range of the
converter.
ε is average DNL of the ADC.
V
NOISE rms is V rms thermal noise referred to the analog input of
the ADC.
PROCESSING GAIN
Processing gain is the improvement in SNR gained through
DSP processes. Most of this processing gain is accomplished
using the channelizer chips. These special-purpose DSP chips
not only provide channel selection and filtering but also provide
a data rate reduction. Few, if any, general-purpose DSPs can accept
and process data at 40.96 MSPS. The required rate reduction is
accomplished through a process called decimation. The term
decimation rate is used to indicate the ratio of input data rate to
output data rate. For example, if the input data rate is 40.96 MSPS
and the output data rate is 30 kSPS, then the decimation rate
is 1365.
Even with the 5.3 mV rms of noise suggested, SNR is limited to
36 dB if injected as broadband noise. To avoid this problem,
noise can be injected as an out-of-band signal. Typically, this may
be around dc but may just as well be at FS/2 or at some other
frequency not used by the receiver. The bandwidth of the noise
is several hundred kilohertz. By band-limiting and controlling
its location in frequency, large levels of dither can be introduced
into the receiver without seriously disrupting receiver
performance. The result can be a marked improvement in the
SFDR of the data converter.
Large processing gains may be achieved in the decimation
and filtering process. The purpose of the channelizer, beyond
tuning, is to provide the narrow-band filtering and selectivity
Rev. B | Page 18 of 24
AD9042
performance. The result can be a marked improvement in the
SFDR of the data converter.
RECEIVER EXAMPLE
To determine how the ADC performance relates to overall
receiver sensitivity, the simple receiver in Figure 42 can be
examined. This example assumes that the overall downconversion
process can be grouped into one set of specifications, instead of
individually examining all components within the system and
summing them together. Although a more detailed analysis
should be employed in a real design, this model provides a good
approximation.
Figure 16 shows the same converter shown in Figure 13 but with
this injection of dither (see Figure 13). SFDR is now 94 dBFS.
Figure 14 and Figure 17 show an SFDR sweep before and after
adding dither.
To fully appreciate the improvement that dither can have on
performance, Figure 15 and Figure 18 show similar dither plots,
one using and one not using dither. Increasing to 128k sample
points lowers the noise floor of the FFT; this simply makes it
easier to see the dramatic reduction in spurious levels resulting
from dither.
In examining a wideband digital receiver, several considerations
must be applied. Although other specifications are important,
receiver sensitivity determines the absolute limits of a radio,
excluding the effects of other outside influences. Assuming that
receiver sensitivity is limited by noise and not by adjacent signal
strength, several sources of noise can be identified and their
overall contribution to receiver sensitivity calculated.
GAIN = 30dB
+15V
LOW CONTROL
(0V TO 1V)
16kΩ
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
1µF
A
NC202
NOISE
2.2kΩ
DIODE
+5V
(Noisecom)
NF = 20dB
BW = 12.5MHz
SINGLE CHANNEL
BW = 30kHz
REF
A
2kΩ
–5V
1kΩ
AD9042
RF/IF
CHANNELIZER
DSP
REF IN
ENCODE
OP27
0.1µF
AD600
OPTIONAL HIGH
POWER DRIVE
CIRCUIT
40.96MHz
Figure 42. Receiver Analysis
39Ω
390Ω
Figure 40. Noise Source (Dither Generator)
The first noise calculation to make is based on the signal
bandwidth at the antenna. In a typical broadband cellular
receiver, the IF bandwidth is 12.5 MHz. Given that the power of
noise in a given bandwidth is defined by Pn = kTB, where B is
bandwidth, k = 1.38 × 10−23 is Boltzmann’s constant, and T =
300k is absolute temperature, this gives an input noise power of
5.18 × 10−14 watts or −102.86 dBm. If the receiver front end has a
gain of 30 dB and a noise figure of 20 dB, then the total noise
presented to the ADC input becomes −52.86 dBm (−102.86 + 30
+ 20) or 0.51 mV rms. Comparing receiver noise to the dither
required for good SFDR, note that in this example, the receiver
supplies about 10% of the dither required for good SFDR.
The simplest method for generating dither is through the use of
a noise diode (see Figure 40). In this circuit, the noise diode,
NC202, generates the reference noise that is gained up and
driven by the AD600 and OP27 amplifier chain. The level of
noise can be controlled by either presetting the control voltage
when the system is set up or by using a digital-to-analog
converter (DAC) to adjust the noise level based on input signal
conditions. Once generated, the signal must be introduced to
the receiver strip. The easiest method is to inject the signal into
the drive chain after the last downconversion, as shown in
Figure 41.
Based on a typical ADC SNR specification of 68 dB, the
equivalent internal converter noise is 0.140 mV rms. Therefore,
total broadband noise is 0.529 mV rms. Before processing gain,
this is an equivalent SNR (with respect to full scale) of 56.5 dB.
Assuming a 30 kHz AMPS signal and a sample rate of 40.96 MSPS,
the SNR, through processing gain, is increased by 28.3 dB to
84.8 dB. However, if eight strong and equal signals are present
in the ADC bandwidth, each must be placed 18 dB below full
scale to prevent ADC overdrive. In addition, 3 dB to 15 dB
should be used for ADC headroom should another signal come
in-band unexpectedly. For this example, 12 dB of headroom can
be allocated. Therefore, 30 dB of range is given away and the
carrier-to-noise ratio (C/N) is reduced to 54.8 dB (C/N is the
ratio of signal to in-band noise).
FROM
RF/IF
AIN
AD9042
V
OFFSET
NOISE SOURCE
V
REF
LPF
Figure 41. Using the AD9042 with Dither
Rev. B | Page 19 of 24
AD9042
Assuming that the C/N ratio must be 6 dB or better for accurate
demodulation, one of the eight signals can be reduced by 48.8 dB
before demodulation becomes unreliable. At this point, the
input signal power would be 40.6 μV rms on the ADC input or
−74.8 dBm. Referenced to the antenna, this is −104.8 dBm.
IF SAMPLING, USING THE AD9042 AS A MIX-
DOWN STAGE
Because the performance of the AD9042 extends beyond the
baseband region into the second and third Nyquist zone, the
converter may find many uses as a mix-down converter in both
narrow-band and wideband applications. Many common IF
frequencies exist in this range of frequencies. If the ADC is used
to sample these signals, they are aliased down to baseband during
the sampling process in much the same manner that a mixer
downconverts a signal. For signals in various Nyquist zones, the
following equations may be used to determine the final
frequency after aliasing.
To improve sensitivity, several things can be done. First, the
noise figure of the receiver can be reduced. Because front-end
noise dominates the 0.529 mV rms, each dB reduction in noise
figure translates to an additional dBc of sensitivity. Second,
providing broadband AGC can improve sensitivity by the range
of the AGC. However, the AGC only provides useful
improvements if all in-band signals are kept to an absolute
minimal power level so that AGC can be kept near the
maximum gain.
f1NYQUISTS = fSAMPLE − fSIGNAL
f2NYQUISTS = abs (fSAMPLE − fSIGNAL
f3NYQUISTS = 2 × (fSAMPLE − fSIGNAL
)
)
This noise-limited example does not adequately demonstrate
the true limitations in a wideband receiver. Other limitations
such as SFDR are more restrictive than SNR and noise. Assume
that the ADC has an SFDR specification of −80 dBFS or −76
dBm (full scale = 4 dBm). Also assume that a tolerable carrier-
to-interferer (C/I) (different from C/N) ratio is 18 dB (C/I is the
ratio of signal to in-band interfere). This means that the
minimum signal level is −62 dBFS (−80 plus 18) or −58 dBm.
At the antenna, this is −88 dBm. Therefore, as can be seen,
SFDR (single or multitone) would limit receiver performance in
this example. However, SFDR can be greatly improved through
the use of dither (see Figure 15 and Figure 18). In many cases,
the addition of the out-of-band dither can improve receiver
sensitivity nearly to that limited by thermal noise.
f4NYQUISTS = abs (2 × fSAMPLE − fSIGNAL
)
Using the converter to alias down these narrow-band or
wideband signals has many potential benefits. First and
foremost is the elimination of a complete mixer stage, along
with amplifiers, filters, and other devices, reducing cost and
power dissipation.
One common example is the digitization of a 21.4 MHz IF using a
10 MSPS sample clock. Using the equation for the fifth Nyquist
zone, the resultant frequency after sampling is 1.4 MHz. Figure 44
shows performance under these conditions. Even under these
conditions, the AD9042 typically maintains better than 80 dB
SFDR.
0
Multitone Performance
ENCODE = 10.0MSPS
AIN = 21.4MHz
Figure 43 shows the AD9042 in a worst-case scenario of four
strong tones spaced fairly close together. In this plot, no dither
was used, and the converter still maintains 85 dBFS of spurious-
free range. As noted in the Overcoming Static Nonlinearities
with Dither section, a modest amount of dither introduced out-
of-band can be used to lower the nonlinear components.
0
–20
–40
–60
8
7
8
6
2
5
3
4
–80
–100
–120
–20
ENCODE = 41MSPS
–40
–60
dc
1
2
3
4
5
FREQUENCY (MHz)
Figure 44. IF Sampling at 21.4 MHz Input
3
6
9
7
4
2
5
8
–80
–100
–120
dc
4.1
8.2
12.3
16.4
20.5
FREQUENCY (MHz)
Figure 43. Multitone Performance
Rev. B | Page 20 of 24
AD9042
RECEIVE CHAIN FOR DIGITAL AND ANALOG BEAM FORMING MEDICAL ULTRASOUND USING
THE AD9042
PRE-AMP
VGA
The AD9042 is an excellent digitizer for digital and analog beam-
forming medical ultrasound systems. The price/performance ratio
of the AD9042 allows ultrasound designers the luxury of using
state-of-the-art ADCs without jeopardizing their cost budgets.
ADC performance is critical for image quality. The high dynamic
range and excellent noise performance of the AD9042 enable
higher image quality medical ultrasound systems.
+14dB TO +20dB –14dB TO +34dB
TRANSDUCER/
PRE-AMP
INPUT
AD9042
AD8041
LPF
AD604
AD7226
Figure 45 shows the AD9042 used in one channel of the receive
chain of a medical ultrasound system. The AD604 receives its
input directly from the transducer or from an external preamp
connected to the transducer. The AD604 contains two separate
stages. The first stage is a preamp with a fixed gain (14 dB to
20 dB) selected by a fixed resistor. The second stage is a variable
gain amplifier with the gain set by the AD7226 DAC. The gain
is increased over time to compensate for the attenuation of
signal level in the body.
Figure 45. Using the AD9042 in Ultrasound Applications
Following the AD604, a low-pass filter is used to minimize the
amount of noise presented to the ADC. The AD8041 is used to
buffer the filter from the AD9042 input. This function may not
be required depending on the filter configuration and PCB
partitioning. The digital outputs of the AD9042 are then presented
to the digital system for processing.
Rev. B | Page 21 of 24
AD9042
OUTLINE DIMENSIONS
12.20
12.00 SQ
11.80
0.75
0.60
0.45
1.60
MAX
44
34
1
33
PIN 1
10.20
10.00 SQ
9.80
TOP VIEW
(PINS DOWN)
1.45
1.40
1.35
0.20
0.09
7°
3.5°
0°
11
23
0.15
0.05
12
22
SEATING
PLANE
0.10
COPLANARITY
VIEW A
0.45
0.37
0.30
0.80
BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BCB
Figure 46. 44-Lead Low Profile Quad Flat Package [LQFP]
(ST-44-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9042ASTZ1
Temperature Range
Package Description
Package Option
−40°C to +85°C
44-Lead Low Profile Quad Flat Package [LQFP]
ST-44-1
1Z = RoHS Compliant Part.
Rev. B | Page 22 of 24
AD9042
NOTES
Rev. B | Page 23 of 24
AD9042
NOTES
©1995–2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00554-0-9/09(B)
Rev. B | Page 24 of 24
©2020 ICPDF网 联系我们和版权申明