AD8177ABPZ [ADI]
500 MHz, Triple 16 】 5 Video Crosspoint Switch; 500兆赫,三16 】 5视频交叉点开关型号: | AD8177ABPZ |
厂家: | ADI |
描述: | 500 MHz, Triple 16 】 5 Video Crosspoint Switch |
文件: | 总40页 (文件大小:664K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
500 MHz, Triple 16 × 5
Video Crosspoint Switch
AD8177
FEATURES
FUNCTIONAL BLOCK DIAGRAM
D0 D1 D2 D3 D4 VPOS VNEG VDD DGND
High channel count, triple 16 × 5 high speed, nonblocking
switch array
Pin compatible with AD8175/AD8176 (16 × 9 switch arrays)
and AD8178 (16 × 5 switch array)
Differential or single-ended operation
Supports sync-on common-mode and sync-on color
operating modes
Decoded HV sync outputs available
G = +2 operation (differential input to differential output)
Flexible power supplies: +5 V or 2.5 V
Logic ground for convenient control interface
Serial or parallel programming of switch array
High impedance output disable allows connection of
multiple devices with minimal loading on output bus
Adjustable output CM and black level through external pins
Excellent ac performance (to support 1600 × 1200 @ 85 Hz)
Bandwidth: 500 MHz
AD8177
A0
A1
A2
SERIN
CLR
SER/PAR
45-BIT SHIFT
REGISTER WITH
5-BIT PARALLEL
LOADING
1
0
WE
SEROUT
CLK
20
25
NO
CONNECT
CS
UPDATE
RST
PARALLEL LATCH
CMENC
25
5
DECODE
5 × 5:16 DECODERS
80
INPUT
RECEIVER
G = +1
OUTPUT
BUFFER
G = +1
Slew rate: 1800 V/μs
Settling time: 4 ns to 1%
Low power of 2.3 W
Low all-hostile crosstalk
2
2
2
2
2
2
R
G
B
R
G
B
H
V
−88 dB @ 5 MHz
−46 dB @ 500 MHz
SWITCH
MATRIX
G = +2
Wide input common-mode range of 4 V
Reset pin allows disabling of all outputs
Fully populated 26 × 26 ball PBGA package
(27 mm × 27 mm, 1 mm ball pitch)
2
2
2
2
R
G
B
R
G
B
H
V
2
2
Convenient grouping of RGB signals for easy routing
APPLICATIONS
RGB video switching
KVM
Professional video
VBLK
VOCM_CMENCON
VOCM_CMENCOFF
Figure 1.
GENERAL DESCRIPTION
The AD8177 is a high speed, triple 16 × 5 video crosspoint
switch matrix. It supports 1600 × 1200 RGB displays @ 85 Hz
refresh rate by offering a 500 MHz bandwidth and a slew rate of
1800 V/μs. With −88 dB of crosstalk and −94 dB isolation
(@ 5 MHz), the AD8177 is useful in many high speed video
applications.
with CM signaling removed through the switch. The output
CM and black level can be conveniently set via external pins.
The independent output buffers of the AD8177 can be placed
into a high impedance state to create larger arrays by paralleling
crosspoint outputs. Inputs can be paralleled as well. The
AD8177 offers both serial and parallel programming modes.
The AD8177 supports two modes of operation: differential-in
to differential-out mode with sync-on CM signaling passed
through the switch and differential-in to differential-out mode
The AD8177 is packaged in a fully populated 26 × 26 ball
PBGA package and is available over the extended industrial
temperature range of −40°C to +85°C.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2007 Analog Devices, Inc. All rights reserved.
AD8177
TABLE OF CONTENTS
Features .............................................................................................. 1
Pin Configuration and Function Descriptions..............................8
Truth Table and Logic Diagram ............................................... 17
Equivalent Circuits......................................................................... 19
Typical Performance Characteristics ........................................... 21
Theory of Operation ...................................................................... 26
Applications Information.............................................................. 27
Operating Modes........................................................................ 27
Programming.............................................................................. 28
Differential and Single-Ended Operation............................... 30
Outline Dimensions....................................................................... 39
Ordering Guide .......................................................................... 39
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Timing Characteristics (Serial Mode) ....................................... 5
Timing Characteristics (Parallel Mode).................................... 6
Absolute Maximum Ratings............................................................ 7
Thermal Resistance ...................................................................... 7
Power Dissipation......................................................................... 7
ESD Caution.................................................................................. 7
REVISION HISTORY
7/07—Revision 0: Initial Version
Rev. 0 | Page 2 of 40
AD8177
SPECIFICATIONS
VS = 2.5 V at TA = 25°C, G = +2, RL = 100 Ω (each output), VBLK = 0 V, output CM voltage = 0 V, differential I/O mode, unless
otherwise noted.
Table 1.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
200 mV p-p
2 V p-p
0.1 dB, 200 mV p-p
2 V p-p
1%, 2 V step
500
450
25
1.3
4
MHz
MHz
MHz
ns
Gain Flatness
Propagation Delay
Settling Time
ns
Slew Rate, Differential Output
2 V step
1800
1500
300
400
V/μs
V/μs
V/μs
V/μs
2 V step, 10% to 90%
1 V step, 10% to 90%
Rail-to-rail, TTL load
Slew Rate, RGB Common Mode
Slew Rate, HV Outputs
NOISE/DISTORTION PERFORMANCE
Crosstalk, All Hostile
f = 5 MHz
f = 10 MHz
f = 100 MHz
f = 500 MHz
f = 5 MHz, RL = 100 Ω, one channel
0.01 MHz to 100 MHz
−88
−82
−58
−46
−94
40
dB
dB
dB
dB
dB
nV/√Hz
Off Isolation, Input to Output
Input Voltage Noise
DC PERFORMANCE
Gain Error
1
%
Gain Matching
R, G, B same channel
0.5
40
%
Gain Temperature Coefficient
OUTPUT CHARACTERISTICS
Output Offset Voltage
ppm/°C
CMENC on or off
Temperature coefficient
CMENC on or off
10
31
10
mV
μV/°C
mV
Output Offset Voltage,
RGB Common Mode
Temperature coefficient
Enabled, differential
Disabled, differential
Disabled
Disabled
No load, differential
Short circuit
−7.6
1.5
2.7
2
μV/°C
Ω
kΩ
pF
μA
Output Impedance
Output Disable Capacitance
Output Leakage Current
Output Voltage Range
Output Current
1
4
2
V p-p
mA
45
INPUT CHARACTERISTICS
Input Voltage Range,
Differential Mode
Input Voltage Range,
Common Mode
V p-p
V
V
IN = 1 V p-p, differential
2.25
CMR, RGB Input
ΔVOUT, DM/ΔVIN, CM, ΔVIN, CM
ΔVOUT, DM/ΔVIN, CM, ΔVIN, CM
ΔVOUT, CM/ΔVIN, CM, ΔVIN, CM
ΔVOUT, CM/ΔVIN, CM, ΔVIN, CM
Any switch configuration
Differential
=
=
=
=
0.5 V, CMENC off
0.5 V, CMENC on
0.5 V CMENC off
0.5 V, CMENC on
–62
−45
−70
0
2
3.33
1
dB
dB
dB
dB
pF
kΩ
μA
CM Gain, RGB Input
Input Capacitance
Input Resistance
Input Offset Current
Rev. 0 | Page 3 of 40
AD8177
Parameter
Conditions
Min
Typ
Max
Unit
SWITCHING CHARACTERISTICS
Enable On Time
50% UPDATE to 50% output
50% UPDATE to 50% output
80
70
ns
ns
Switching Time, 2 V Step
POWER SUPPLIES
Supply Current
VPOS, outputs enabled, no load
Outputs disabled
VNEG, outputs enabled, no load
Outputs disabled
DVDD, outputs enabled, no load
VPOS − VNEG
VDD to DGND
460
290
460
290
mA
mA
mA
mA
mA
V
V
dB
dB
4
Supply Voltage Range
PSR
4.5 to 5.5
3.3 to 5.5
−55
ΔVOUT, DM/ΔVPOS, ΔVPOS
ΔVOUT, DM/ΔVNEG, ΔVNEG
=
=
0.5 V
0.5 V
−55
OPERATING TEMPERATURE RANGE
Temperature Range
θJA
Operating (still air)
Operating (still air)
−40 to +85
15
°C
°C/W
Rev. 0 | Page 4 of 40
AD8177
TIMING CHARACTERISTICS (SERIAL MODE)
Table 2.
Limit
Typ
Parameter
Symbol
Min
40
60
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
μs
ns
Serial Data Setup Time
CLK Pulse Width
t1
t2
t3
t4
t5
t6
t7
Serial Data Hold Time
CLK Pulse Separation
CLK to UPDATE Delay
UPDATE Pulse Width
CLK to SEROUT Valid
Propagation Delay, UPDATE to Switch On
Data Load Time, CLK = 5 MHz, Serial Mode
RST Time
50
140
10
90
120
80
9
140
200
t2
t4
1
CLK
0
LOAD DATA INTO
SERIAL REGISTER
ON FALLING EDGE
t1
t3
1
0
SERIN
OUT4 (D4)
OUT4 (D3)
OUT0 (D0)
t5
t6
1 = LATCHED
TRANSFER DATA FROM SERIAL
REGISTER TO PARALLEL
LATCHES DURING LOW LEVEL
UPDATE
0 = TRANSPARENT
t7
1
SEROUT
0
Figure 2. Timing Diagram, Serial Mode
Table 3. Logic Levels, VDD = 3.3 V
VIH
VIL
VOH
SEROUT
VOL
IIH
IIL
IOH
IOL
SER/PAR, CLK,
SER/PAR, CLK,
SEROUT
SER/PAR, CLK,
SER/PAR, CLK,
SEROUT
SEROUT
SERIN, UPDATE SERIN, UPDATE
SERIN, UPDATE SERIN, UPDATE
2.0 V min 0.6 V max
2.8 V min
0.4 V max
20 μA max
–20 μA max
–1 mA min
1 mA min
Table 4. H and V Logic Levels, VDD = 3.3 V
VOH
VOL
IOH
IOL
2.7 V min
0.5 V max
–3 mA max
3 mA max
RST
Table 5.
VIH
Logic Levels, VDD = 3.3 V
VIL
IIH
IIL
2.0 V min
0.6 V max
−60 μA max
−120 μA max
CS
Table 6.
VOH
Logic Levels, VDD = 3.3 V
VOL
IIH
IOL
2.0 V min
0.6 V max
100 μA max
40 μA max
Rev. 0 | Page 5 of 40
AD8177
TIMING CHARACTERISTICS (PARALLEL MODE)
Table 7.
Limit
Typ
Parameter
Symbol
Min
80
110
150
90
Max
Unit
ns
ns
Parallel Data Setup Time
WE Pulse Width
t1
t2
t3
t4
t5
t6
Parallel Hold Time
ns
ns
WE Pulse Separation
WE to UPDATE Delay
UPDATE Pulse Width
Propagation Delay, UPDATE to Switch On
RST Time
10
ns
90
ns
80
ns
140
200
ns
t2
t4
1
0
WE
t1
t3
1
D0 TO D4
A0 TO A2
0
t5
t6
1 = LATCHED
UPDATE
0 = TRANSPARENT
Figure 3. Timing Diagram, Parallel Mode
Table 8. Logic Levels, VDD = 3.3 V
VIH
VIL
VOH
VOL
IIH
IIL
SER/PAR, WE,
IOH
IOL
SER/PAR, WE,
SER/PAR, WE,
SEROUT
SEROUT
SER/PAR, WE,
SEROUT
SEROUT
D0, D1, D2, D3, D0, D1, D2, D3,
D4, A0, A1, A2, D4, A0, A1, A2,
D0, D1, D2, D3, D0, D1, D2, D3,
D4, A0, A1, A2, D4, A0, A1, A2,
UPDATE
UPDATE
UPDATE
UPDATE
2.0 V min
0.6 V max
Disabled
Disabled
20 μA max
−20 μA max
Disabled
Disabled
Table 9. H and V Logic Levels, VDD = 3.3 V
VOH
VOL
IOH
IOL
2.7 V min
0.5 V max
–3 mA max
3 mA max
RST
Table 10.
VIH
Logic Levels, VDD = 3.3 V
VIL
IIH
IIL
2.0 V min
0.6 V max
−60 μA max
−120 μA max
CS
Table 11.
VOH
Logic Levels, VDD = 3.3 V
VOL
IIH
IOL
2.0 V min
0.6 V max
100 μA max
40 μA max
Rev. 0 | Page 6 of 40
AD8177
ABSOLUTE MAXIMUM RATINGS
Table 12.
POWER DISSIPATION
Parameter
Rating
The AD8177 is operated with 2.5 V or +5 V supplies and can
drive loads down to 100 ꢀ, resulting in a large range of possible
power dissipations. For this reason, extra care must be taken
derating the operating conditions based on ambient temperature.
Analog Supply Voltage (VPOS – VNEG
Digital Supply Voltage (VDD – DGND
Ground Potential Difference
)
)
6 V
6 V
+0.5 V to −2.5 V
(VNEG – DGND
Maximum Potential Difference
(VDD – VNEG
Common-Mode Analog Input Voltage (VNEG – 0.5 V)
to (VPOS + 0.5 V)
Differential Analog Input Voltage
Digital Input Voltage
Output Voltage
)
Packaged in a 676-lead PBGA the AD8177 junction-to-ambient
thermal impedance (θJA) is 15°C/W. For long-term reliability,
the maximum allowed junction temperature of the die should
not exceed 150°C. Temporarily exceeding this limit may cause
a shift in parametric performance due to a change in stresses
exerted on the die by the package. Exceeding a junction
temperature of 175°C for an extended period can result in
device failure. The following curve shows the range of allowed
internal die power dissipations that meet these conditions over
the −40°C to +85°C ambient temperature range. When using
Table 13, do not include external load power in the maximum
power calculation, but do include load current dropped on the
die output transistors.
8 V
)
2 V
VDD
(VPOS – 1 V) to (VNEG + 1 V)
(Disabled Analog Output)
Output Short-Circuit Duration
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
Momentary
−65°C to +125°C
−40°C to +85°C
300°C
150°C
10
T
= 150°C
J
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
9
8
7
6
5
4
3
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 13. Thermal Resistance
15
25
35
45
55
65
75
85
AMBIENT TEMPERATURE (°C)
Package Type
θJA
Unit
Figure 4. Maximum Die Power Dissipation vs. Ambient Temperature
PBGA
15
°C/W
ESD CAUTION
Rev. 0 | Page 7 of 40
AD8177
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
VNEG
VNEG
VNEG
NC
NC
VNEG
OPR4
ONB4
VPOS
IPR8
INB8
VNEG
IPR9
INB9
VPOS
IPR10
INB10
VNEG
IPR11
INB11
VPOS
IPR12
INB12
VNEG
VNEG
VNEG
A
A
VNEG
VNEG
VNEG
VNEG
VPOS
ONB3
OPR3
VNEG
NC
VNEG
VNEG
VNEG
VNEG
VPOS
OPB3
ONR3
VNEG
NC
VNEG
VNEG
VNEG
VNEG
VPOS
ONG3
OPG3
VNEG
NC
NC
NC
NC
VNEG
VNEG
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
ONR4
OPG4
H4
OPB4
ONG4
V4
VPOS
VPOS
VPOS
DGND
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
DGND
VPOS
VNEG
VNEG
INR8
IPG8
IPB8
ING8
VNEG
VNEG
VPOS
CS
INR9
IPG9
IPB9
ING9
VPOS
VPOS
INR10
IPG10
VPOS
A2
IPB10
ING10
VPOS
A1
VNEG
VNEG
VPOS
A0
INR11
IPG11
VPOS
CLR
IPB11
ING11
VPOS
VDD
VPOS
VPOS
VPOS
DGND
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
DGND
VPOS
VNEG
VNEG
INR12
IPG12
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
IPB12
ING12
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
IPG4
VNEG
VNEG
IPG13
ING13
VPOS
VPOS
IPG14
ING14
VNEG
IPG15
ING15
VPOS
VPOS
IPG7
VNEG
VNEG
INR13
IPB13
VPOS
VPOS
INR14
IPB14
VNEG
INR15
IPB15
VPOS
VPOS
INR7
VNEG
VNEG
IPR13
INB13
VPOS
VPOS
IPR14
INB14
VNEG
IPR15
INB15
VPOS
VPOS
IPR7
B
B
NC
C
C
NC
NC
VPOS
VDD
VPOS
SEROUT
VPOS
CLK
VPOS
SERIN
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
CMENC
VPOS
IPG1
VPOS
D
D
SER/PAR
VPOS
VPOS
V3
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
NC
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
V0
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
H0
E
E
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VDD
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
RST
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
UPDATE
VPOS
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
WE
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
D4
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
D3
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
D2
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
D1
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
D0
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VDD
F
F
G
G
H3
H
H
VPOS
NC
J
J
K
K
NC
NC
NC
NC
L
L
VPOS
ONB2
OPR2
VNEG
NC
VPOS
OPB2
ONR2
VNEG
NC
VPOS
ONG2
OPG2
VNEG
NC
VPOS
V2
M
N
M
N
VOCM_
CMENCON
H2
VBLK
P
P
VOCM_
CMENCOFF
VPOS
NC
R
R
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
ING4
ING7
IPB7
INB7
T
T
NC
NC
NC
NC
VNEG
IPG6
VNEG
INR6
VNEG
IPR6
U
U
VPOS
ONB1
OPR1
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
OPB1
ONR1
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
ONG1
OPG1
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
V1
V
V
ING6
IPB6
INB6
W
Y
W
Y
H1
VPOS
VPOS
IPG5
VPOS
VPOS
INR5
VPOS
VPOS
IPR5
VPOS
VPOS
NC
AA
AB
AC
AD
AE
AF
AA
AB
AC
AD
AE
AF
VPOS
ING0
VPOS
IPG0
VPOS
ING1
VPOS
VNEG
VNEG
VPOS
ING2
VPOS
IPG2
VPOS
VPOS
VPOS
VPOS
ING3
VPOS
IPG3
ING5
IPB5
INB5
NC
NC
ONG0
OPB0
OPG0
ONR0
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
NC
NC
IPB0
INR0
IPB1
INR1
IPB2
INR2
IPB3
INR3
IPB4
INR4
VNEG
VNEG
VNEG
NC
NC
VPOS
ONB0
OPR0
VNEG
INB0
IPR0
VPOS
INB1
IPR1
VNEG
INB2
IPR2
VPOS
INB3
IPR3
VNEG
INB4
IPR4
VNEG
VNEG
VNEG
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Figure 5. Pin Configuration, Package Bottom View
Rev. 0 | Page 8 of 40
AD8177
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
A
B
VNEG
VNEG
VNEG
INB12
IPR12
VPOS
INB11
IPR11
VNEG
INB10
IPR10
VPOS
INB9
IPR9
VNEG
INB8
IPR8
VPOS
ONB4
OPR4
VNEG
NC
NC
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
ONB3
OPR3
VNEG
NC
A
B
VNEG
VNEG
IPR13
INB13
VPOS
VPOS
IPR14
INB14
VNEG
IPR15
INB15
VPOS
VPOS
IPR7
VNEG
VNEG
INR13
IPB13
VPOS
VPOS
INR14
IPB14
VNEG
INR15
IPB15
VPOS
VPOS
INR7
VNEG
VNEG
IPG13
ING13
VPOS
VPOS
IPG14
ING14
VNEG
IPG15
ING15
VPOS
VPOS
IPG7
IPB12
ING12
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
IPG4
INR12
IPG12
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
DGND
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
DGND
VPOS
VNEG
VNEG
VNEG
6
IPB11
ING11
VPOS
VDD
INR11
IPG11
VPOS
CLR
VNEG
VNEG
VPOS
A0
IPB10
ING10
VPOS
A1
INR10
IPG10
VPOS
A2
VPOS
VPOS
VPOS
SER/PAR
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
D4
IPB9
ING9
INR9
IPG9
VNEG
VNEG
VPOS
CS
IPB8
ING8
INR8
IPG8
VPOS
VPOS
VPOS
DGND
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
DGND
VPOS
VNEG
VNEG
VNEG
18
OPB4
ONG4
V4
ONR4
OPG4
H4
VNEG
VNEG
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
21
NC
NC
NC
VNEG
VNEG
VNEG
VNEG
VPOS
ONG3
OPG3
VNEG
NC
VNEG
VNEG
VNEG
VNEG
VPOS
OPB3
ONR3
VNEG
NC
C
NC
C
D
VPOS
SERIN
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
CMENC
VPOS
IPG1
VPOS
CLK
VPOS
SEROUT
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
RST
VPOS
VDD
NC
NC
D
E
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
H0
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
V0
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
NC
VPOS
VPOS
V3
E
F
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VDD
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
D0
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
D1
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
D2
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
D3
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
WE
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
UPDATE
VPOS
VPOS
VPOS
VPOS
15
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VDD
F
G
G
H
H3
H
J
VPOS
NC
J
K
K
L
NC
NC
NC
NC
L
M
N
VPOS
V2
VPOS
ONG2
OPG2
VNEG
NC
VPOS
OPB2
ONR2
VNEG
NC
VPOS
ONB2
OPR2
VNEG
NC
M
N
VOCM_
CMENCON
P
VBLK
H2
P
VOCM_
CMENCOFF
R
VPOS
NC
R
T
INB7
IPB7
ING7
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
ING4
IPB4
T
U
VNEG
IPR6
VNEG
INR6
VNEG
IPG6
NC
NC
NC
NC
U
V
VPOS
V1
VPOS
ONG1
OPG1
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
24
VPOS
OPB1
ONR1
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
25
VPOS
ONB1
OPR1
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
26
V
W
Y
INB6
IPB6
ING6
W
Y
VPOS
VPOS
IPR5
VPOS
VPOS
INR5
VPOS
VPOS
IPG5
H1
AA
AB
AC
AD
AE
AF
VPOS
VPOS
NC
AA
AB
AC
AD
AE
AF
INB5
IPB5
ING5
VPOS
IPG3
VPOS
ING3
VPOS
VPOS
VPOS
VPOS
9
VPOS
IPG2
VPOS
ING2
VPOS
VNEG
VNEG
VNEG
12
VPOS
ING1
VPOS
IPG0
VPOS
ING0
VNEG
VNEG
VNEG
1
VNEG
VNEG
VNEG
2
VNEG
VNEG
VNEG
3
OPG0
ONR0
OPR0
19
ONG0
OPB0
ONB0
20
NC
NC
INR4
INR3
IPB3
INR2
IPB2
INR1
IPB1
INR0
IPB0
NC
NC
IPR4
INB4
5
IPR3
INB3
IPR2
INB2
IPR1
INB1
IPR0
INB0
NC
NC
4
7
8
10
11
13
14
16
17
22
23
Figure 6. Pin Configuration, Package Top View
Rev. 0 | Page 9 of 40
AD8177
Table 14. Ball Grid Function Descriptions
Ball No. Mnemonic
Description
Ball No. Mnemonic
Description
A1
A2
A3
A4
A5
A6
A7
A8
VNEG
VNEG
VNEG
INB12
IPR12
VPOS
INB11
IPR11
VNEG
INB10
IPR10
VPOS
INB9
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 12, Negative Phase.
Input Number 12, Positive Phase.
Positive Analog Power Supply.
Input Number 11, Negative Phase.
Input Number 11, Positive Phase.
Negative Analog Power Supply.
Input Number 10, Negative Phase.
Input Number 10, Positive Phase.
Positive Analog Power Supply.
Input Number 9, Negative Phase.
Input Number 9, Positive Phase.
Negative Analog Power Supply.
Input Number 8, Negative Phase.
Input Number 8, Positive Phase.
Positive Analog Power Supply.
Output Number 4, Negative Phase.
Output Number 4, Positive Phase.
Negative Analog Power Supply.
No Connect.
B26
C1
C2
C3
C4
C5
C6
C7
C8
VNEG
VNEG
VNEG
VNEG
ING12
IPG12
VPOS
ING11
IPG11
VNEG
ING10
IPG10
VPOS
ING9
IPG9
VNEG
ING8
IPG8
VPOS
ONG4
OPG4
VNEG
NC
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 12, Negative Phase.
Input Number 12, Positive Phase.
Positive Analog Power Supply.
Input Number 11, Negative Phase.
Input Number 11, Positive Phase.
Negative Analog Power Supply.
Input Number 10, Negative Phase.
Input Number 10, Positive Phase.
Positive Analog Power Supply.
Input Number 9, Negative Phase.
Input Number 9, Positive Phase.
Negative Analog Power Supply.
Input Number 8, Negative Phase.
Input Number 8, Positive Phase.
Positive Analog Power Supply.
Output Number 4, Negative Phase.
Output Number 4, Positive Phase.
Negative Analog Power Supply.
No Connect.
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23
D24
IPR9
VNEG
INB8
IPR8
VPOS
ONB4
OPR4
VNEG
NC
NC
No Connect.
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
IPB12
INR12
VPOS
IPB11
INR11
VNEG
IPB10
INR10
VPOS
IPB9
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 12, Positive Phase.
Input Number 12, Negative Phase.
Positive Analog Power Supply.
Input Number 11, Positive Phase.
Input Number 11, Negative Phase.
Negative Analog Power Supply.
Input Number 10, Positive Phase.
Input Number 10, Negative Phase.
Positive Analog Power Supply.
Input Number 9, Positive Phase.
Input Number 9, Negative Phase.
Negative Analog Power Supply.
Input Number 8, Positive Phase.
Input Number 8, Negative Phase.
Positive Analog Power Supply.
Output Number 4, Positive Phase.
Output Number 4, Negative Phase.
Negative Analog Power Supply.
No Connect.
NC
No Connect.
VNEG
VNEG
VNEG
IPR13
INR13
IPG13
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
V4
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 13, Positive Phase.
Input Number 13, Negative Phase.
Input Number 13, Positive Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Output Number 4, V Sync.
INR9
VNEG
IPB8
INR8
VPOS
OPB4
ONR4
VNEG
NC
NC
VNEG
VNEG
H4
VPOS
NC
NC
VNEG
Output Number 4, H Sync.
Positive Analog Power Supply.
No Connect.
No Connect.
Negative Analog Power Supply.
No Connect.
Negative Analog Power Supply.
Negative Analog Power Supply.
Rev. 0 | Page 10 of 40
AD8177
Ball No. Mnemonic
Description
Ball No. Mnemonic
Description
D25
D26
E1
E2
E3
E4
E5
E6
E7
VNEG
VNEG
INB13
IPB13
ING13
VPOS
VPOS
DGND
VDD
CLR
A0
A1
A2
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 13, Negative Phase.
Input Number 13, Positive Phase.
Input Number 13, Negative Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Digital Power Supply.
F25
F26
G1
G2
G3
G4
G5
G6
G7
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
V3
ONG3
OPB3
ONB3
IPR14
INR14
IPG14
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
H3
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Output Number 3, V Sync.
Output Number 3, Negative Phase.
Output Number 3, Positive Phase.
Output Number 3, Negative Phase.
Input Number 14, Positive Phase.
Input Number 14, Negative Phase.
Input Number 14, Positive Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Output Number 3, H Sync.
Digital Power Supply.
Internal Register Clearing
E8
E9
G8
G9
Control Pin 0, Output Address Bit 0.
Control Pin 1, Output Address Bit 1.
Control Pin 2, Output Address Bit 2.
Control Pin: Serial Parallel Select Mode.
Control Pin: Serial Data In.
E10
E11
E12
E13
E14
E15
E16
E17
E18
E19
E20
E21
E22
E23
E24
E25
E26
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
G10
G11
G12
G13
G14
G15
G16
G17
G18
G19
G20
G21
G22
G23
G24
G25
G26
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
H11
H12
H13
H14
H15
H16
H17
H18
H19
H20
H21
H22
H23
H24
SER/PAR
SERIN
CLK
Control Pin: Serial Data Clock.
Control Pin: Chip Select.
CS
SEROUT
VDD
Control Pin: Serial Data Out.
Digital Power Supply.
Digital Power Supply.
DGND
VPOS
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
OPG3
Output Number 3, Positive Phase.
Rev. 0 | Page 11 of 40
AD8177
Ball No. Mnemonic
Description
Ball No. Mnemonic
Description
H25
H26
J1
J2
J3
J4
J5
J6
J7
ONR3
OPR3
INB14
IPB14
ING14
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
NC
Output Number 3, Negative Phase.
Output Number 3, Positive Phase.
Input Number 14, Negative Phase.
Input Number 14, Positive Phase.
Input Number 14, Negative Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
No Connect.
K25
K26
L1
L2
L3
L4
L5
L6
L7
NC
NC
No Connect.
No Connect.
IPR15
INR15
IPG15
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
NC
Input Number 15, Positive Phase.
Input Number 15, Negative Phase.
Input Number 15, Positive Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
No Connect.
J8
J9
L8
L9
J10
J11
J12
J13
J14
J15
J16
J17
J18
J19
J20
J21
J22
J23
J24
J25
J26
K1
K2
K3
K4
K5
K6
K7
K8
K9
K10
K11
K12
K13
K14
K15
K16
K17
K18
K19
K20
K21
K22
K23
K24
L10
L11
L12
L13
L14
L15
L16
L17
L18
L19
L20
L21
L22
L23
L24
L25
L26
M1
M2
M3
M4
M5
M6
M7
M8
M9
M10
M11
M12
M13
M14
M15
M16
M17
M18
M19
M20
M21
M22
M23
M24
NC
NC
NC
No Connect.
No Connect.
No Connect.
INB15
IPB15
ING15
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
VPOS
Input Number 15, Negative Phase.
Input Number 15, Positive Phase.
Input Number 15, Negative Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
NC
No Connect.
Rev. 0 | Page 12 of 40
AD8177
Ball No. Mnemonic
Description
Ball No. Mnemonic
Description
M25
M26
N1
N2
N3
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
P25
P26
R1
R2
R3
ONR2
OPR2
IPR7
INR7
IPG7
VPOS
Output Number 2, Negative Phase.
Output Number 2, Positive Phase.
Input Number 7, Positive Phase.
Input Number 7, Negative Phase.
Input Number 7, Positive Phase.
Positive Analog Power Supply.
N4
R4
N5
VOCM_
CMENCON
Output CM Reference with CM
Encoding On.
R5
VOCM_
CMENCOFF
Output Reference with CM
Encoding Off.
N6
N7
N8
N9
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
V2
ONG2
OPB2
ONB2
VPOS
VPOS
VPOS
VPOS
VBLK
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
H2
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Output Number 2, V Sync.
Output Number 2, Negative Phase.
Output Number 2, Positive Phase.
Output Number 2, Negative Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Output Blank Level.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Output Number 2, H Sync.
R6
R7
R8
R9
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
INB7
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 7, Negative Phase.
Input Number 7, Positive Phase.
Input Number 7, Negative Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
No Connect.
N10
N11
N12
N13
N14
N15
N16
N17
N18
N19
N20
N21
N22
N23
N24
N25
N26
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
R10
R11
R12
R13
R14
R15
R16
R17
R18
R19
R20
R21
R22
R23
R24
R25
R26
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
T11
T12
T13
T14
T15
T16
T17
T18
T19
T20
T21
T22
T23
T24
IPB7
ING7
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
NC
OPG2
Output Number 2, Positive Phase.
NC
No Connect.
Rev. 0 | Page 13 of 40
AD8177
Ball No. Mnemonic
Description
Ball No. Mnemonic
Description
T25
T26
U1
U2
U3
U4
U5
U6
U7
NC
NC
No Connect.
No Connect.
V25
V26
W1
W2
W3
W4
W5
W6
W7
VPOS
VPOS
INB6
Positive Analog Power Supply.
Positive Analog Power Supply.
Input Number 6, Negative Phase.
Input Number 6, Positive Phase.
Input Number 6, Negative Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Output Number 1, V Sync.
Output Number 1, Negative Phase.
Output Number 1, Positive Phase.
Output Number 1, Negative Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Output Number 1, H Sync.
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
NC
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
No Connect.
IPB6
ING6
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
V1
ONG1
OPB1
ONB1
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
H1
U8
U9
W8
W9
U10
U11
U12
U13
U14
U15
U16
U17
U18
U19
U20
U21
U22
U23
U24
U25
U26
V1
V2
V3
V4
V5
V6
V7
V8
V9
V10
V11
V12
V13
V14
V15
V16
V17
V18
V19
V20
V21
V22
V23
V24
W10
W11
W12
W13
W14
W15
W16
W17
W18
W19
W20
W21
W22
W23
W24
W25
W26
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
Y10
Y11
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y20
Y21
Y22
Y23
Y24
NC
NC
NC
IPR6
INR6
IPG6
No Connect.
No Connect.
No Connect.
Input Number 6, Positive Phase.
Input Number 6, Negative Phase.
Input Number 6, Positive Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
VPOS
VPOS
VPOS
VPOS
OPG1
Output Number 1, Positive Phase.
Rev. 0 | Page 14 of 40
AD8177
Ball No. Mnemonic
Description
Ball No. Mnemonic
Description
Y25
Y26
AA1
AA2
AA3
AA4
AA5
AA6
ONR1
OPR1
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VNEG
VNEG
VNEG
IPR5
Output Number 1, Negative Phase.
Output Number 1, Positive Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 5, Positive Phase.
Input Number 5, Negative Phase.
Input Number 5, Positive Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Digital Power Supply.
AB25
AB26
AC1
AC2
AC3
AC4
AC5
AC6
AC7
VNEG
VNEG
INB5
IPB5
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 5, Negative Phase.
Input Number 5, Positive Phase.
Input Number 5, Negative Phase.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Output Number 0, H Sync.
ING5
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
VPOS
H0
AA7
AA8
AA9
AC8
AC9
AA10
AA11
AA12
AA13
AA14
AA15
AA16
AA17
AA18
AA19
AA20
AA21
AA22
AA23
AA24
AA25
AA26
AB1
AB2
AB3
AB4
AB5
AB6
AB7
AB8
AB9
AB10
AB11
AB12
AB13
AB14
AB15
AB16
AB17
AB18
AB19
AB20
AB21
AB22
AB23
AB24
AC10
AC11
AC12
AC13
AC14
AC15
AC16
AC17
AC18
AC19
AC20
AC21
AC22
AC23
AC24
AC25
AC26
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
AD16
AD17
AD18
AD19
AD20
AD21
AD22
AD23
AD24
V0
VPOS
NC
Output Number 0, V Sync.
Positive Analog Power Supply.
No Connect.
NC
No Connect.
VNEG
VNEG
VNEG
VNEG
VNEG
VNEG
IPG4
ING4
VNEG
IPG3
ING3
VPOS
IPG2
ING2
VNEG
IPG1
ING1
VPOS
IPG0
ING0
VNEG
OPG0
ONG0
VPOS
NC
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 4, Positive Phase.
Input Number 4, Negative Phase.
Negative Analog Power Supply.
Input Number 3, Positive Phase.
Input Number 3, Negative Phase.
Positive Analog Power Supply.
Input Number 2, Positive Phase.
Input Number 2, Negative Phase.
Negative Analog Power Supply.
Input Number 1, Positive Phase.
Input Number 1, Negative Phase.
Positive Analog Power Supply.
Input Number 0, Positive Phase.
Input Number 0, Negative Phase.
Negative Analog Power Supply.
Output Number 0, Positive Phase.
Output Number 0, Negative Phase.
Positive Analog Power Supply.
No Connect.
INR5
IPG5
VPOS
VPOS
DGND
VDD
D0
D1
D2
D3
Digital Power Supply.
Control Pin, Input Address Bit 0.
Control Pin, Input Address Bit 1.
Control Pin, Input Address Bit 2.
Control Pin, Input Address Bit 3.
Control Pin, Input Address Bit 4.
Control Pin, Pass/Stop CM Encoding.
Control Pin, 1st Rank Write Strobe.
Control Pin, 2nd Rank Write Strobe.
Control Pin, 2nd Rank Data Reset.
Digital Power Supply.
D4
CMENC
WE
UPDATE
RST
VDD
DGND
VPOS
VPOS
VPOS
VPOS
VPOS
VNEG
Digital Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Positive Analog Power Supply.
Negative Analog Power Supply.
NC
VNEG
No Connect.
Negative Analog Power Supply.
Rev. 0 | Page 15 of 40
AD8177
Ball No. Mnemonic
Description
Ball No. Mnemonic
Description
AD25
AD26
AE1
AE2
AE3
AE4
AE5
AE6
AE7
VNEG
VNEG
VNEG
VNEG
VNEG
INR4
IPB4
VNEG
INR3
IPB3
VPOS
INR2
IPB2
VNEG
INR1
IPB1
VPOS
INR0
IPB0
VNEG
ONR0
OPB0
VPOS
NC
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 4, Negative Phase.
Input Number 4, Positive Phase.
Negative Analog Power Supply.
Input Number 3, Negative Phase.
Input Number 3, Positive Phase.
Positive Analog Power Supply.
Input Number 2, Negative Phase.
Input Number 2, Positive Phase.
Negative Analog Power Supply.
Input Number 1, Negative Phase.
Input Number 1, Positive Phase.
Positive Analog Power Supply.
Input Number 0, Negative Phase.
Input Number 0, Positive Phase.
Negative Analog Power Supply.
Output Number 0, Negative Phase.
Output Number 0, Positive Phase.
Positive Analog Power Supply.
No Connect.
AE26
AF1
AF2
AF3
AF4
AF5
AF6
AF7
AF8
VNEG
VNEG
VNEG
VNEG
IPR4
INB4
VNEG
IPR3
INB3
VPOS
IPR2
INB2
VNEG
IPR1
INB1
VPOS
IPR0
INB0
VNEG
OPR0
ONB0
VPOS
NC
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Input Number 4, Positive Phase.
Input Number 4, Negative Phase.
Negative Analog Power Supply.
Input Number 3, Positive Phase.
Input Number 3, Negative Phase.
Positive Analog Power Supply.
Input Number 2, Positive Phase.
Input Number 2, Negative Phase.
Negative Analog Power Supply.
Input Number 1, Positive Phase.
Input Number 1, Negative Phase.
Positive Analog Power Supply.
Input Number 0, Positive Phase.
Input Number 0, Negative Phase.
Negative Analog Power Supply.
Output Number 0, Positive Phase.
Output Number 0, Negative Phase.
Positive Analog Power Supply.
No Connect.
AE8
AE9
AF9
AF10
AF11
AF12
AF13
AF14
AF15
AF16
AF17
AF18
AF19
AF20
AF21
AF22
AF23
AF24
AF25
AF26
AE10
AE11
AE12
AE13
AE14
AE15
AE16
AE17
AE18
AE19
AE20
AE21
AE22
AE23
AE24
AE25
NC
No Connect.
NC
VNEG
VNEG
No Connect.
Negative Analog Power Supply.
Negative Analog Power Supply.
VNEG
VNEG
VNEG
Negative Analog Power Supply.
Negative Analog Power Supply.
Negative Analog Power Supply.
Rev. 0 | Page 16 of 40
AD8177
TRUTH TABLE AND LOGIC DIAGRAM
Table 15. Operation Truth Table
WE
X1
UPDATE CLK
RST
SER/PAR CS
SERIN
SEROUT
CMENC
Operation/Comment
X
X
X
X
0
X
X
X
Asynchronous reset. All outputs
are disabled. Contents of the
45-bit shift register are
unchanged.
1
0
1
SERINi
SERINi-45
1
1
0
0
X
X
Serial mode. The data on the
SERIN line is loaded into the
45-bit shift register. The first bit
clocked into the shift register
appears at SEROUT 45 clock
cycles later. Data is not applied
to the switch array.
Parallel mode. The data on
parallel lines D0 through D4 is
loaded into the shift register
location addressed by A0
through A2. Data is not applied
to the switch array.
1
1
X
X
1
0
1
1
0
1
X
X
X
X
1
1
X
1
0
0
X
X
Switch array update. Data in
the 45-bit shift register is trans-
ferred to the parallel latches
and applied to the switch array.
X
X
No change in logic.
1 X = don’t care.
Rev. 0 | Page 17 of 40
AD8177
2 9 0 - 5 6 0 0 6
R
D E C E O D 5 O T 3
S S R E A D D
T U P T O U
Figure 7. Logic Diagram
Rev. 0 | Page 18 of 40
AD8177
EQUIVALENT CIRCUITS
VPOS
0.1pF
10kΩ
10kΩ
OPn, ONn
VBLK,
VOCM_CMENCOFF
0.1pF
1kΩ
1kΩ
VNEG
(VPOS – VNEG)
2
Figure 13. VBLK and VOCM_CMENCOFF Inputs
(see also ESD Protection Map, Figure 19)
Figure 8. Enabled Output (see also ESD Protection Map, Figure 19)
VPOS
VPOS
20kΩ
OPn
0.3pF
3.33kΩ
3.33kΩ
20kΩ
3.4pF
VOCM_CMENCON
VNEG
0.4pF
3.1kΩ
VPOS
0.3pF
3.4pF
20kΩ
ONn
VNEG
20kΩ
VNEG
Figure 9. Disabled Output (see also ESD Protection Map, Figure 19)
Figure 14. VOCM_CMENCON Input (see also ESD Protection Map, Figure 19)
VDD
2500Ω
10kΩ
2525Ω
IPn
INn
1.3pF
1.3pF
25kΩ
0.3pF
1kΩ
RST
2500Ω
2525Ω
DGND
RST
Figure 15.
Input (see also ESD Protection Map, Figure 19)
Figure 10. Receiver, Differential (see also ESD Protection Map, Figure 19)
IPn
1.3pF
2500Ω
CLK, SER/PAR, WE,
UPDATE, SERIN
A[2:0], D[4:0],
0.3pF
10kΩ
1kΩ
2500Ω
1.3pF
CMENC, CLR
INn
DGND
Figure 11. Receiver Simplified Equivalent Circuit When Driving Differentially
Figure 16. Logic Input (see also ESD Protection Map, Figure 19)
IPn
1.6pF
2.5kΩ
1kΩ
CS
25kΩ
INn
DGND
Figure 12. Receiver Simplified Equivalent Circuit
When Driving Single-Ended
CS
Figure 17. Input (see also ESD Protection Map, Figure 19)
Rev. 0 | Page 19 of 40
AD8177
VPOS
VDD
VDD
CLK, RST,
SER/PAR,
WE,
UPDATE,
SERIN,
SEROUT,
A[2:0],
IPn, INn,
OPn, ONn, VBLK,
VOCM_CMENCOFF
VOCM_CMENCON
SEROUT,
H, V
D[4:0],
CMENC,
CS, CLR
DGND
VNEG
DGND
Figure 19. ESD Protection Map
Figure 18. SEROUT, H, V Logic Outputs
(see also ESD Protection Map, Figure 19)
Rev. 0 | Page 20 of 40
AD8177
TYPICAL PERFORMANCE CHARACTERISTICS
VS = 2.5 V at TA = 25°C, G = +2, RL = 100 Ω (each output), VBLK = 0 V, output CM voltage = 0 V, differential I/O mode, unless
otherwise noted.
12
10
8
0.15
0.10
0.05
0
6
4
2
0
–0.05
–0.10
–0.15
–2
–4
–6
1
10
100
1000
2
4
6
8
10
12
14
16
18
20
FREQUENCY (MHz)
TIME (ns)
Figure 23. Small Signal Pulse Response, 200 mV p-p
Figure 20. Small Signal Frequency Response, 200 mV p-p
1.5
1.0
12
10
8
0.5
6
4
0
2
–0.5
–1.0
–1.5
0
–2
–4
–6
2
4
6
8
10
12
14
16
18
20
1
10
100
1000
TIME (ns)
FREQUENCY (MHz)
Figure 24. Large Signal Pulse Response, 2 V p-p
Figure 21. Large Signal Frequency Response, 2 V p-p
5
1.2
0.8
0.4
0
16
14
12
10
8
V
10pF
5pF
IN
0
–5
2pF
0pF
–10
–15
–20
–25
6
4
V
OUT
–0.4
–0.8
–1.2
2
ERROR
0
–2
–4
0
1
2
3
4
5
6
7
8
9
10
1
10
100
1000
TIME (ns)
FREQUENCY (MHz)
Figure 25. Settling Time
Figure 22. Small Signal Frequency Response with Capacitive Loads
Rev. 0 | Page 21 of 40
AD8177
0
–20
5
4
3
2
–40
1
–60
0
–1
–2
–3
–4
–80
–100
–120
–5
0
1
10
100
1000
1
2
3
4
5
6
7
8
9
10
FREQUENCY (MHz)
TIME (ns)
Figure 26. Settling Time, 1% Zoom
Figure 29. Crosstalk, All Hostile
2
1
6000
5000
4000
3000
2000
1000
0
0
–20
0
–40
–1
–2
–3
–4
–5
1850V/µs PEAK
–60
–80
–100
–120
–1000
10
0
1
2
3
4
5
6
7
8
9
1
10
100
1000
TIME (ns)
FREQUENCY (MHz)
Figure 30. Crosstalk, Off Isolation
Figure 27. Large Signal Rising Edge Slew Rate
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–20
–40
CMENC HIGH
CMENC LOW
–60
–80
–100
–120
1
10
100
1000
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 31. Common-Mode Rejection
Figure 28. Crosstalk, All Hostile, Single-Ended
Rev. 0 | Page 22 of 40
AD8177
600
10000
500
400
300
200
100
0
ALL OUTPUTS ENABLED
ALL OUTPUTS DISABLED
1000
100
1
10
100
1000
–50 –40 –30 –20 –10
0
10 20 30 40 50 60 70 80 90 100
FREQUENCY (MHz)
TEMPERATURE (°C)
Figure 32. Quiescent Supply Currents vs. Temperature
Figure 35. Input Impedance
3000
2500
2000
1500
1000
500
10000
1000
0
100
1
10
100
1000
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 33. Output Impedance, Disabled
Figure 36. Input Impedance, Single-Ended
120
100
80
60
40
20
0
0
–10
–20
–30
–40
–50
–60
–70
–80
1
10
100
1000
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 34. Output Impedance, Enabled
Figure 37. Output Balance Error
Rev. 0 | Page 23 of 40
AD8177
1.0
0.5
0
20
15
10
5
2500
2250
2000
1750
1500
1250
1000
750
RED
GREEN
BLUE
–0.5
HSYNC
VSYNC
–1.0
–1.5
0
500
250
–5
0
0
0
100 200 300 400 500 600 700 800 900 1000
–70 –60 –50 –40 –30 –20 –10
0
10 20 30 40 50 60 70
TIME (ns)
V
(mV)
OS
Figure 38. Common-Mode Pulse Response
Figure 41. VOS Distribution
2.0
1.5
–10
–20
–30
–40
–50
–60
–70
–80
–90
1.0
31µV/°C
0.5
0
–0.5
–1.0
–1.5
–2.0
1
10
100
1000
–40
–20
0
20
40
60
80
100
FREQUENCY (MHz)
TEMPERATURE (°C)
Figure 42. VOS Drift, RTO
Figure 39. Common-Mode Isolation, CMENC Low
0.6
0.4
200
160
120
80
0.2
–7.6µV/°C
0
–0.2
–0.4
–0.6
40
0
–40
–20
0
20
40
60
80
100
0
10
20
30
40
50
60
70
80
90
100
TEMPERATURE (°C)
FREQUENCY (MHz)
Figure 43. VOS Drift, Common Mode, RTO
Figure 40. Noise Spectral Density
Rev. 0 | Page 24 of 40
AD8177
6
5
1.2
1.0
0.8
0.6
0.4
0.2
0
0.025
0.020
0.015
0.010
0.005
0
V
UPDATE
OUT
4
3
40ppm/°C
2
–0.005
–0.010
–0.015
–0.020
–0.025
1
0
–1
–0.2
0
20 40 60 80 100 120 140 160 180 200 220 240 260 280
–40
–20
0
20
40
60
80
100
TIME (ns)
TEMPERATURE (°C)
Figure 44. Enable Time
Figure 45. Normalized DC Gain vs. Temperature
Rev. 0 | Page 25 of 40
AD8177
THEORY OF OPERATION
The AD8177 is a nonblocking crosspoint with 16 differential
RGB input channels and 5 differential RGB output channels.
Although the AD8177 is primarily meant for differential-in,
differential-out, middle-of-Cat-5-run applications, each differ-
ential RGB output channel is complemented by H and V syncs
for use in end-of-Cat-5-run, single-ended output applications.
The outputs of the AD8177 can be disabled to minimize on-
chip power dissipation. When disabled, there is a feedback
network of approximately 2.7 kꢀ between the differential outputs.
This high impedance allows multiple ICs to be bussed together
without additional buffering. Care must be taken to reduce
output capacitance, which can result in overshoot and frequency-
domain peaking. A series of internal amplifiers drive internal
nodes such that wideband high impedance is presented at the
disabled output, even while the output bus experiences fast signal
swings. When the outputs are disabled and driven externally, the
voltage applied to them should not exceed the valid output
swing range for the AD8177 to keep these internal amplifiers
in their linear range of operation. Applying excessive differential
voltages to the disabled outputs can cause damage to the AD8177
and should be avoided (see the Absolute Maximum Ratings
section of this data sheet for guidelines).
Processing of common-mode (CM) voltage levels is achieved by
placing the AD8177 in either of its two operation modes. In the
first operation mode (CMENC low), the input CM of each RGB
differential pair (possibly present either in the form of sync-on
CM signaling or noise) is removed through the switch, and the
output CM is set to a global reference voltage via the VOCM_
CMENCOFF analog input. Therefore, the AD8177 can behave
as a differential-in, differential-out switch. If sync-on CM signaling
is present at the differential RGB inputs, then the H and V outputs
represent decoded syncs. In the second operation mode, input
sync-on CM signaling is propagated through the switch. Note
that in this mode, as in the previous one, the overall input CM
is blocked through the switch. In this mode, the overall output
CM is set to a global reference voltage via the VOCM_CMENCON
analog input.
The connectivity of the AD8177 is controlled by a flexible TTL-
compatible logic interface. Either parallel or serial loading into
a first rank of latches preprograms each output. A global update
signal moves the programming data into the second rank of
latches, simultaneously updating all outputs. In serial mode,
a serial-out pin allows devices to be daisy-chained together for
single-pin programming of multiple ICs. A power-on reset pin
is available to avoid bus conflicts by disabling all outputs. This
power-on reset clears the second rank of latches but does not
clear the first rank of latches. In serial mode, preprogramming
individual inputs is not possible and the entire shift register needs
to be flushed. A global chip-select pin gates the input clock and
the global update signal to the second rank of buffers.
In either operation mode, input pin VBLK defines the black
level of the positive output phase. The combination of VBLK
and VOCM_CMENCOFF allows the user to position the positive
and negative output phases anywhere in the allowable output
voltage range.
The switch is organized into five 16:1 RGB multiplexers, with each
being responsible for connecting an RGB input channel to its
respective RGB output channel. Decoding logic selects a single
input (or none) in each multiplexer and connects it to its respective
output. Feedback around each multiplexer realizes a closed-
loop differential-in, differential-out gain of +2. A second loop
realizes a closed-loop common-mode-in gain of +1.
The AD8177 can operate on a single 5 V supply, powering both
the signal path (with the VPOS/VNEG supply pins) and the
control logic interface (with the VDD/DGND supply pins).
Split supply operation is possible with 2.5 V supplies to easily
interface to ground-referenced video signals. In this case,
a flexible logic interface allows the control logic supplies
(VDD/DGND) to be run off 5 V/0 V to 3.3 V/0 V, and the
analog core remains on split supplies. Additional flexibility in
the analog output common-mode level (VOCM_CMENCOFF)
and output black level (VBLK) facilitates operation with unequally
split supplies. If +3 V/−2 V supplies to +2 V/−3 V supplies are
desired, the output CM can still be set to 0 V for ground-referenced
video signals.
Each differential RGB input channel is buffered by a differential
receiver, which is capable of accepting input CM voltages extending
all the way to either supply rail. In addition to passing differential
information, each receiver processes and routes input CM
voltages. Excess closed-loop receiver bandwidth reduces the
receiver’s effect on the overall device bandwidth.
The output stage is designed for fast slew rate and settling time
while driving a series-terminated Cat-5 cable. Unlike competing
multiplexer designs, the small signal bandwidth closely
approaches the large signal bandwidth.
Rev. 0 | Page 26 of 40
AD8177
APPLICATIONS INFORMATION
The positive and negative outputs are shown with VOCM_
OPERATING MODES
CMENCOFF and VBLK both set to 0 V. (Note that both pulses
have been slightly shifted off the 0 V line for clarity.)
VOCM_CMENCOFF = 0V
Depending on the state of the CMENC logic input, the AD8177
can be set in either of two differential-in, differential-out operating
modes. An additional application is possible by tapping the outputs
single-ended and making use of the decoded H and V outputs.
0.7V
POSITIVE
PHASE
Middle-of-Cat-5-Run Application, CM Encoding Turned Off
VBLK = 0V
In this application, the AD8177 is placed somewhere in the
middle of a Cat-5 run. By tying CMENC low, the CM of each
RGB differential pair is removed through the device (or turned
off), while the overall CM at the output is defined by the reference
value VOCM_CMENCOFF. In this mode of operation, CM noise
is removed, while the intended differential RGB signals are
buffered and passed to the outputs. The AD8177 is placed in
this operation mode when used in a sync-on color scheme.
Figure 46 shows the voltage levels and CM handling for a single
input channel connected to a single output channel in a middle-
of-Cat-5-run application with CM encoding turned off.
NEGATIVE
PHASE
–0.7V
Figure 47. Output for 0 V to 0.7 V Input Differential Pulse, VBLK = 0 V,
VOCM_CMENCOFF = 0 V
As a second example, refer to Figure 48. VCOM_CMENCOFF
is set to +0.35 V, and VBLK is set to −0.35 V. The input is still
a differential pulse with a low level of 0 V and a high level of
0.7 V. Note how the positive phase and the negative phase are
now shifted with respect to each other by an amount equal to
VBLK − VOCM_CMENCOFF or −0.35 V − 0.35 V = −0.7 V.
Because the negative output phase spans the same voltage range
as the positive output phase, the usable voltage range for single-
ended applications is effectively doubled over the previous example.
(Note that the output pulses have been slightly shifted with
respect to each other for clarity.)
DIFF. R
DIFF. B
CM
R
CM
B
DIFF. R
DIFF. B
CM
DIFF. G
G
AD8177
INPUT
OVERALL
CM
CM
CM
R
B
OUTPUT
OVERALL
CM
CM
G
DIFF. G
CMENC
VOCM_CMENCOFF = +0.35V
NEGATIVE
PHASE
VOCM_CMENCOFF
0.7V
Figure 46. AD8177 in a Middle-of-Cat-5-Run Application, CM Encoding Off
(Note that in this application, the H and V outputs,
though asserted, are not used.)
VBLK = –0.35V
0V
Input VBLK and Input VOCM_CMENCOFF allow the user
complete flexibility in defining the output CM level and the
amount of overlap between the positive and negative phases,
thus maximizing output headroom usage. Whenever VBLK
differs from VOCM_CMENCOFF by more than approximately
100 mV, a differential voltage Δdiff is added at the outputs
according to the expression Δdiff = VBLK − VOCM_CMENCOFF.
Conversely, whenever the difference between VBLK and
VOCM_CMENCOFF is less than approximately 100 mV,
no differential voltage is added at the outputs.
POSITIVE
PHASE
Figure 48. Output for 0 V to 0.7 V Input Differential Pulse,
VBLK = −0.35 V, VOCM_CMENCOFF = +0.35 V
Middle-of-Cat-5-Run Application, CM Encoding Turned On
In this application, the AD8177 is also placed somewhere in the
middle of a Cat-5 run, although the common-mode handling is
different. By tying CMENC high, the CM of each RGB input is
passed through the part, while at the same time, the overall output
CM is stripped and set equal to the voltage applied at the VOCM_
CMENCON pin. The AD8177 is placed in this operation mode
when used with a sync-on CM scheme. Although asserted, the
H and V outputs are not used in this application. Figure 49 shows
the voltage levels and CM handling for a single input channel
connected to a single output channel in a middle-of-Cat-5-run
application with CM encoding turned on.
As a first example, refer to Figure 47. The positive phase of a
differential output is shown by the solid line, while the negative
phase is shown by the dashed line. The input to the crosspoint is
a positive differential pulse with a low level of 0 V and a high
level of 0.7 V.
Rev. 0 | Page 27 of 40
AD8177
DIFF. R
PROGRAMMING
DIFF. B
CM
R
DIFF. R
The AD8177 has two options for changing the programming of
the crosspoint matrix. In the first option, a serial word of 45 bits
can be provided that updates the entire matrix each time. The
second option allows for changing the programming of a single
output via a parallel interface. The serial option requires fewer
signals, but more time (clock cycles) for changing the program-
ming; the parallel programming technique requires more
signals but allows for changing a single output at a time,
therefore requiring fewer clock cycles.
CM
B
DIFF. B
CM
R
CM
B
AD8177
INPUT
OVERALL
CM
OUTPUT
OVERALL
CM
DIFF. G
CM
G
DIFF. G
CM
G
CMENC
VOCM_CMENCON
Serial Programming Description
Figure 49. AD8177 in Middle-of-Cat-5-Run Application, CM Encoding On
(Note that in this application, the H and V outputs,
though asserted, are not used.)
CS CLK
,
The serial programming mode uses the device pins
UPDATE SER
/PAR. The first step is to enable the
,
SERIN,
CLK
, and
CS
In this operation mode, the difference Δdiff = VBLK − VOCM_
CMENCOFF still adds an output differential voltage, as described
in the Middle-of-Cat-5-Run Application, CM Encoding Turned
Off section.
SER
by pulling
the serial programming mode. The parallel clock
held high during the entire serial programming operation.
UPDATE
low. Next,
/PAR is pulled low to enable
WE
should be
The
shifted into the serial port of the device. Although the data still
UPDATE
signal should be high during the time that data is
End-of-Cat-5-Run, CM Encoding Turned Off
In this application, each AD8177 output is tapped single-ended
at the positive phase and followed by a fast buffer to drive
a monitor at the end of a Cat-5 run (a suitable choice is the
AD8003 set up in a noninverting configuration with gain of +4).
The H and V outputs can then be used to drive the monitor
sync inputs directly. The relationship between the incoming
sync-on CM signaling and the H and V syncs is defined according
to Table 16.
shifts in when
is low, the transparent, asynchronous
latches allow the shifting data to reach the matrix. This causes
the matrix to try to update to every intermediate state as defined
by the shifting data.
CLK
The data at SERIN is clocked in at every falling edge of
.
A total of 45 bits must be shifted in to complete the programming.
A total of five bits must be supplied for each of the five RGB
output channels: an output enable bit (D4) and four bits (D3
to D0) that determine the input channel. If D4 is low (output
disabled), the four associated bits (D3 to D0) do not matter
because no input is switched to that output. A sequence of five
bits at Logic 0 must be supplied in between each D4 to D0
group of bits for padding purposes. There are a total of four such
sequences of zeros.
Table 16. H and V Sync Truth Table (VPOS/VNEG
=
2.5 V)
V
CMR
0.5
0
CMG
CMB
H
0
0
−0.5
0
Low
Low
High
High
High
Low
Low
High
0.5
0.5
−0.5
−0.5
0
0.5
The most significant output-address data is shifted in first, with
the enable bit (D4) shifted in first, followed by the input address
(D3 to D0) entered sequentially with D3 first and D0 last. The first
sequence of five bits at Logic 0 is shifted in next. Each remaining
output is programmed sequentially in a similar fashion, until
the least-significant-output-address data is shifted in. Note that
the last D4 to D0 group is not followed by a corresponding group
The following two statements are equivalent to the truth table
(see Table 16) in producing H and V for all allowable CM inputs:
•
H sync is high when the CM of Blue is larger than the CM
of Red.
•
V sync is high when the combined CM of Red and Blue is
larger than the CM of Green.
UPDATE
of five zeros. At this point,
causes the programming of the device according to the data that
UPDATE
can be taken low, which
was just shifted in. The
latches are asynchronous; and
is low, they are transparent.
UPDATE
when
Rev. 0 | Page 28 of 40
AD8177
If more than one AD8177 device is to be serially programmed
in a system, the SEROUT signal from one device can be
connected to the SERIN of the next device to form a serial
To change the programming of an output via parallel program-
CS
SER
UPDATE
ming,
should be taken low, while /PAR and
CLK
should be taken high. The serial programming clock,
should be left high during parallel programming. The parallel
WE
,
CLK UPDATE SER
chain. All of the
,
, and /PAR pins should be
connected in parallel and operated as described previously. The
serial data is input to the SERIN pin of the first device of the
chain, and it ripples through to the last. Therefore, the data for
the last device in the chain should come at the beginning of the
programming sequence. The length of the programming sequence
clock,
, should start in the high state. The 3-bit address of
the output to be programmed should be put on A2 to A0. Data
Bit D3 to Data Bit D0 should contain the information that identifies
the input that gets programmed to the output that is addressed.
Data Bit D4 determines the enabled state of the output. If D4 is low
(output disabled), the data on D3 to D0 does not matter.
CS
is 45 bits times the number of devices in the chain.
gates the
is held high, both
are held in their inactive high state. When
CLK UPDATE
CLK
CLK
UPDATE
UPDATE
CS
signals, so that when
and
and
After the desired address and data signals have been established,
they can be latched into the shift register by a high-to-low transi-
CS
is held low, both
and
function normally.
WE
UPDATE
tion of the
until the
signal. The matrix is not programmed, however,
signal is taken low. It is thus possible to latch
in new data for several or all of the outputs first via successive
WE UPDATE
Parallel Programming Description
When using the parallel programming mode, it is not necessary
to reprogram the entire device when making changes to the
matrix. In fact, parallel programming allows modification of
a single output or more at a time. Because this takes only one
negative transitions of
then have all the new data take effect when
while
is held high, and
UPDATE
goes low.
This is the technique that should be used when programming
the device for the first time after power-up when using parallel
programming.
WE UPDATE
/
cycle, significant time savings can be realized by
using parallel programming.
Programming the device to a known state can be accomplished
in serial programming mode by clocking in the entire 45-bit
sequence immediately after reset or power-up.
One important consideration in using parallel programming is
RST
that the
signal does not reset all registers in the AD8177.
RST
When taken low, the
signal only sets each output to the
disabled state. This is helpful during power-up to ensure that
two parallel outputs are not active at the same time.
Reset
When powering up the AD8177, it is usually desirable to have
RST
the outputs come up in the disabled state. The
taken low, causes all outputs to be in the disabled state. However,
RST
pin, when
After initial power-up, the internal registers in the device
RST
generally have random data, even though the
signal has
the
signal does not reset all registers in the AD8177. This
been asserted. If parallel programming is used to program one
output, then that output is properly programmed, but the rest
of the device has a random program state, depending on the
internal register content at power-up. Therefore, when using
parallel programming, it is essential that the device be pro-
grammed to a desired state after power-up. This ensures that
the programming matrix is always in a known state. From then
on, parallel programming can be used to modify a single output
or more at a time.
is important when operating in the parallel programming mode.
Refer to the Serial Programming Description section for informa-
tion about programming internal registers after power-up. Serial
programming programs the entire matrix each time, so no
special considerations apply.
Because the data in the shift register is random after power-up,
it should not be used to program the matrix, or the matrix can
enter unknown states. To prevent this, do not apply a logic low
UPDATE
UPDATE
In similar fashion, if
is taken low after initial power-up,
signal to
should first be loaded with the desired data, and only then can
the
initially after power-up. The shift register
the random power-up data in the shift register is programmed into
the matrix. Therefore, to prevent the crosspoint from being
programmed into an unknown state, do not apply a logic level
after power is initially applied. Programming the
device into a known state after reset or power-up is a one-time
event that is accomplished by the following two steps:
UPDATE
be taken low to program the device.
RST
The
pin has a 20 kꢀ pull-up resistor to VDD that can be
UPDATE
to
used to create a simple power-up reset circuit. A capacitor from
RST RST
to ground holds
low for some time while the rest of the
device stabilizes. The low condition causes all the outputs to be
disabled. The capacitor then charges through the pull-up resistor
to the high state, thus allowing full programming capability of
the device.
1. First, Output 4 to Output 0 are programmed to the off-state
while holding the CLR input at a logic high.
2. Next, each output (Output 4 to Output 0) is programmed to
its desired state while holding the CLR input at a logic low.
CLR is held at logic low thereafter.
Rev. 0 | Page 29 of 40
AD8177
When operating with a differential input, care must be taken to
keep the common-mode, or average, of the input voltages
within the linear operating range of the AD8177 receiver. For
the AD8177 receiver, this common-mode range can extend rail-
to-rail, provided the differential signal swing is small enough to
avoid forward biasing the ESD diodes (it is safest to keep the
common-mode plus differential signal excursions within the
supply voltages of the part).
DIFFERENTIAL AND SINGLE-ENDED OPERATION
Although the AD8177 has fully differential inputs and outputs,
it can also be operated in a single-ended fashion. Single-ended
and differential configurations are discussed in the following
sections, along with implications on gain, impedances, and
terminations.
Differential Input
Each differential input to the AD8177 is applied to a differential
receiver. These receivers allow the user to drive the inputs with
an uncertain common-mode voltage, such as from a remote
source over twisted pair. The receivers respond only to the
differences in input voltages and restore an internal common-
mode suitable for the internal signal path. Noise or crosstalk,
which affect the inputs of each receiver equally, are rejected by
the input stage, as specified by its common-mode rejection ratio
(CMRR).
The input voltage of the AD8177 is linear for 1 V of differential
input voltage difference (this limitation is primarily due to
ability of the output to swing close to the rails because the
differential gain through the part is +2). Beyond this level,
the signal path saturates and limits the signal swing. This is not
a desired operation, because the supply current increases and
the signal path is slow to recover from clipping. The absolute
maximum allowed differential input signal is limited by long-
term reliability of the input stage. The limits in the Absolute
Maximum Ratings section of the data sheet should be observed
to avoid degrading device performance permanently.
Furthermore, the overall common-mode voltage of all three
differential pairs comprising an RGB channel is processed and
rejected by a separate circuit block. For example, a static discharge
or a resistive voltage drop in a middle-of-Cat-5-run with sync-
on CM signaling coupling into all three pairs in an RGB channel
are rejected at the output of the AD8177, and the sync-on
CM signals are allowed through the switch.
AC Coupling of Inputs
It is possible to ac-couple the inputs of the AD8177 receiver,
so that bias current does not need to be supplied externally.
A capacitor in series with the inputs to the AD8177 creates
a high-pass filter with the input impedance of the device. This
capacitor needs to be sized large enough so that the corner
frequency includes all frequencies of interest.
The circuit configuration used by the differential input receivers
is similar to that of several Analog Devices general-purpose
differential amplifiers, such as the AD8131. The topology is that
of a voltage-feedback amplifier with internal gain resistors. The
input differential impedance for each receiver is 5 kꢀ in parallel
with 10 kꢀ or 3.33 kꢀ, as shown in Figure 50.
Single-Ended Input
The AD8177 input receiver can be driven single-endedly
(unbalanced). Single-ended inputs apply a component of
common-mode signal to the receiver inputs, which is then
rejected by the receiver (see the Specifications section for
common-mode-to-differential-mode ratio of the part).
R
F
R
G
IN+
IN–
OUT–
OUT+
TO SWITCH
MATRIX
The single-ended input resistance, RIN, differs from the
differential input impedance, and is equal to
RCVR
R
CM
R
G
RG
RF
R
F
RIN
=
1 −
Figure 50. Input Receiver Equivalent Circuit
2 × (RG + RF )
This impedance creates a small differential termination error
if the user does not account for the 3.33 kꢀ parallel element.
However, this error is less than 1% in most cases. Additionally,
the source impedance driving the AD8177 appears in parallel
with the internal gain-setting resistors, such that there may be
a gain error for some values of source resistance. The AD8177
is adjusted such that its gain is correct when driven by a back-
terminated Cat-5 cable (25 ꢀ effective impedance to ground at
each input pin, or 100 ꢀ differential source impedance across
pairs of input pins). If a different source impedance is presented,
the differential gain of the AD8177 can be calculated as
with RG and RF, as shown in Figure 50.
Note that this value is smaller than the differential input
resistance, but it is larger than RG. The difference is due to the
component of common-mode level applied to the receiver by
single-ended inputs. A second, smaller component of input
resistance (RCM, also shown in Figure 50) is present across the
inputs in both single-ended and differential operation.
In single-ended operation, an input is driven, and the undriven
input is often tied to midsupply or ground. Because signal-
frequency current flows at the undriven input, such input
should be treated as a signal line in the board design.
2.525 kꢀ
Gdm
=
2.5 kꢀ+ RS
where RS is the effective impedance to ground at each input pin.
Rev. 0 | Page 30 of 40
AD8177
For example, to achieve best dynamic performance, the undriven
input should be terminated with an impedance matching that seen
by the part at the driven input.
Termination
The AD8177 is designed to drive 100 ꢀ terminated to ground
on each output (or an effective 200 ꢀ differential) while meeting
data sheet specifications over the specified operating tempera-
ture range, if care is taken to observe the maximum power
derating curves.
Differential Output
Benefits of Differential Operation
The AD8177 has a fully-differential switch core with differential
outputs. The two output voltages move in opposite directions,
with a differential feedback loop maintaining a fixed output
stage differential gain of +2. This differential output stage
provides improved crosstalk cancellation due to parasitic
coupling from one output to another being equal and out of
phase. Additionally, if the output of the device is utilized in a
differential design, then noise, crosstalk, and offset voltages
generated on-chip that are coupled equally into both outputs
are reduced by the common-mode rejection ratio of the next
device in the signal chain. By utilizing the AD8177 outputs in a
differential application, the best possible noise and offset
specifications can be realized.
Termination at the load end is recommended to shorten settling
time and for best signal integrity. In differential signal paths, it
is often desirable to series-terminate the outputs, with a resistor
in series with each output. A side effect of termination is an
attenuation of the output signal by a factor of two. In this case,
gain is usually necessary somewhere else in the signal path to
restore the signal level.
Whenever a differential output is used single-ended, it is desir-
able to terminate the used single-ended output with a series
resistor, as well as to place a resistor on the unused output to
match the load seen by the used output.
When disabled, the outputs float to midsupply. A small current
is required to drive the outputs away from their midsupply state.
This current is easily provided by an AD8177 output (in its enabled
state) bussed together with the disabled output. Exceeding the
allowed output voltage range may saturate internal nodes in the
disabled output, and consequently, an increase in disabled output
current may be observed.
Common-Mode Gain
The common mode, or average voltage of pairs of output
signals, is set by the voltage on the VOCM_CMENCOFF pin
when common-mode encoding is off (CMENC is logic low), or
by the voltage on the VOCM_CMENCON pin when common-
mode encoding is on (CMENC is logic high). Note that in the
latter case, VCOM_CMENCON sets the overall common-mode
of RGB triplets of differential outputs, while the individual
common-mode of each RGB output is free to change. VCOM_
CMENCON and VCOM_CMENCOFF are typically set to
midsupply (often ground), but can be moved approximately
0.5 V to accommodate cases where the desired output common-
mode voltage may not be midsupply (as in the case of unequal
split supplies). Adjusting the output common-mode voltage
beyond 0.5 V can limit differential swing internally below the
specifications on the data sheet. The overall common mode of
the output voltages follows the voltage applied to VOCM_
CMENCON or VCOM_CMENCOFF, implying a gain of +1.
Likewise, sync-on common-mode signaling is carried through
the AD8177 (CMENC must be in its high state), implying a gain
of +1 for this path, as well.
Single-Ended Output
Usage
The AD8177 output pairs can be used single-ended, taking only
one output and not using the second. This is often desired to
reduce the routing complexity in the design, or because a single-
ended load is being driven directly. This mode of operation
produces good results, but has some shortcomings when compared
to taking the output differentially. When observing the single-
ended output, noise that is common to both outputs appears in
the output signal.
When observing the output as single-ended, the distribution of
offset voltages appears greater. In the differential case, the difference
between the outputs, when the difference between the inputs is
zero, is a small differential offset. This offset is created from
mismatches in devices in the signal path. In the single-ended
case, this differential offset is still observed, but an additional
offset component is also relevant. This additional component is
the common-mode offset, which is the difference between the
average of the outputs and the output common-mode reference.
This offset is created by mismatches that affect the signal path
in a common-mode manner. A differential receiver rejects this
common-mode offset voltage, but in the single-ended case, this
offset is observed with respect to the signal ground. The single-
ended output sums half the differential offset voltage and all of the
common-mode offset voltage for a net increase in observed offset.
The common-mode reference pins are analog signal inputs,
common to all output stages on the device. They require only
small amounts of bias current, but noise appearing on these
pins is buffered to all the output stages. As such, they should
be connected to low noise, low impedance voltage references
to avoid being sources of noise, offset, and crosstalk in the
signal path.
Rev. 0 | Page 31 of 40
AD8177
This supply fluctuation appears as crosstalk in all outputs,
attenuated by the power supply rejection ratio (PSRR) of the
device. At low frequencies, this is a negligible component of
crosstalk, but PSRR falls off as frequency increases. With the
use of differential, balanced loads, as one output draws current
from the positive supply, the other output draws current from
the negative supply. When the phase alternates, the first output
draws current from the negative supply and the second from the
positive supply. The effect is that a more constant current is
drawn from each supply, such that the crosstalk-inducing
supply fluctuation is minimized.
Single-Ended Gain
The AD8177 operates as a closed-loop differential amplifier.
The primary control loop forces the difference between the
output terminals to be a ratio of the difference between the
input terminals. One output increases in voltage, while the
other decreases an equal amount to make the total output
voltage difference correct. The average of these output voltages
is forced to the voltage on the common-mode reference terminal
(VOCM_CMENCOFF or VOCM_CMENCON) by a second
control loop. If only one output terminal is observed with respect
to the common-mode reference terminal, only half of the differ-
ence voltage is observed. This implies that when using only one
output of the device, half of the differential gain is observed.
An AD8177 taken with single-ended output appears to have
a gain of +1.
A third benefit of driving balanced loads is that the output pulse
response changes as load changes. The differential signal control
loop in the AD8177 forces the difference of the outputs to be
a fixed ratio to the difference of the inputs. If the two output
responses are different due to loading, the control loop sees this
difference as signal response error and attempts to correct this
error. The output signal is distorted from the ideal response,
compared to the case when the two outputs are balanced.
It is important to note that all considerations applying to the
used output phase regarding output voltage headroom, apply
unchanged to the complement output phase even if this is not
actually used.
Decoupling
Termination
The signal path of the AD8177 is based on high open-loop gain
amplifiers with negative feedback. Dominant-pole compensation
is used on-chip to stabilize these amplifiers over the range of
expected applied swing and load conditions. To guarantee this
designed stability, proper supply decoupling is necessary with
respect to both the differential control loops and the common-
mode control loops of the signal path. Signal-generated currents
must return to their sources through low impedance paths at all
frequencies in which there is still loop gain (up to 700 MHz at
a minimum).
When operating the AD8177 with a single-ended output, the
preferred output termination scheme is to refer the load to the
output common mode. A series-termination can be used, at an
additional cost of one half the signal gain.
In single-ended output operation, the complementary phase
of the output is not used and may or may not be terminated
locally. Although the unused output can be floated to reduce
power dissipation, there are several reasons for terminating the
unused output with a load resistance matched to the load on the
signal output.
The signal path compensation capacitors in the AD8177 are
connected to the VNEG supply. At high frequencies, this limits
the power supply rejection ratio (PSRR) from the VNEG supply
to a lower value than that from the VPOS supply. When possible,
an application board should be designed such that the VNEG
power is supplied from a low inductance plane, subject to the
least amount of noise.
One component of crosstalk is magnetic coupling by mutual
inductance between output package traces and bond wires that
carry load current. In a differential design, there is coupling
from one pair of outputs to other adjacent pairs of outputs. The
differential nature of the output signal simultaneously drives the
coupling field in one direction for one phase of the output and
in an opposite direction for the other phase of the output. These
magnetic fields do not couple equally into adjacent output pairs
due to different proximities, but they do destructively cancel the
crosstalk to some extent. If the load current in each output is
equal, this cancellation is greater, and less adjacent crosstalk is
observed (regardless of whether the second output is actually
being used).
VOCM_CMENCON and VOCM_CMENCOFF are high speed
common-mode control loops of all output drivers. In the single-
ended output sense, there is no rejection from noise on these
inputs to the outputs. For this reason, care must be taken to
produce low noise sources over the entire range of frequencies
of interest. This is important not only to single-ended operation but
to differential operation, as well, because there is a common-mode-
to-differential gain conversion that becomes greater at higher
frequencies.
A second benefit of balancing the output loads in a differential
pair is the reduction of fluctuations in current requirements
from the power supply. In single-ended loads, the load currents
alternate from the positive supply to the negative supply. This
creates a parasitic signal voltage in the supply pins due to the
finite resistance and inductance of the supplies.
VOCM_CMENCON and VOCM_CMENCOFF are internally
buffered to prevent transient currents from flowing into or out
of these inputs and becoming sources of crosstalk by acting on
their respective source impedances.
Rev. 0 | Page 32 of 40
AD8177
V
POS
Power Dissipation
Calculation of Power Dissipation
I
O, QUIESCENT
10
QNPN
QPNP
T
= 150°C
J
V
I
OUTPUT
9
8
7
6
5
4
3
OUTPUT
I
O, QUIESCENT
V
NEG
Figure 52. Simplified Output Stage
Example
With an ambient temperature of 85°C, all five RGB output channels
driving 1 Vrms into 100 ꢀ loads, and power supplies at 2.5 V,
follow these steps:
15
25
35
45
55
65
75
85
AMBIENT TEMPERATURE (°C)
1. Calculate power dissipation using data sheet quiescent
currents. Neglect VDD current because it is insignificant.
Figure 51. Maximum Die Power Dissipation vs. Ambient Temperature
The curve in Figure 51 was calculated from the following:
TJUNCTION, MAX − TAMBIENT
PD,QUIESCENT = (VPOS × IVPOS) + (VNEG × IVNEG
)
(4)
PD,QUIESCENT = (2.5 V × 460 mA) + (2.5 V × 460 mA) = 2.3 W
PD, MAX
=
(1)
θJA
2. Calculate power dissipation from loads. For a differential
output and ground-referenced load, the output power is
symmetrical in each output phase.
As an example, if the AD8177 is enclosed in an environment
at 45°C (TA), the total on-chip dissipation under all load and
supply conditions must not be allowed to exceed 7.0 W.
PD, OUTPUT = (VPOS − VOUTPUT, RMS) × IOUTPUT, RMS
PD, OUTPUT = (2.5 V − 1 V) × 1 V/100 Ω = 15 mW
There are 15 output pairs, or 30 output currents.
nPD, OUTPUT = 30 × 15 mW = 0.45 W
(5)
When calculating on-chip power dissipation, it is necessary to
include the power dissipated in the output devices due to
current flowing in the loads. For a sinusoidal output about
ground and symmetrical split supplies, the on-chip power
dissipation due to the load can be approximated by
3. Subtract quiescent output stage current for the number
of loads (30 in this example). The output stage is either
standing or driving a load, but the current needs to be
counted only once (valid for output voltages > 0.5 V).
PD,OUTPUT = (VPOS − VOUTPUT,RMS) × IOUTPUT,RMS
(2)
For nonsinusoidal output, the power dissipation should be
calculated by integrating the on-chip voltage drop across the
output devices multiplied by the load current over one period.
PDQ, OUTPUT = (VPOS − VNEG) × IOUTPUT, QUIESCENT
PDQ, OUTPUT = (2.5 V − (−2.5 V)) × 1.65 mA = 8.25 mW
There are 15 output pairs, or 30 output currents.
nPDQ, OUTPUT = 30 × 8.25 mW = 0.25 W
(6)
The user can subtract the quiescent current for the Class AB
output stage when calculating the loaded power dissipation.
For each output stage driving a load, subtract a quiescent power,
according to
4. Verify that power dissipation does not exceed the maximum
allowed value.
PDQ, OUTPUT = (VPOS − VNEG) × IOUTPUT, QUIESCENT
(3)
where IOUTPUT, QUIESCENT = 1.65 mA for each single-ended output
pin of the AD8177.
PD, ON-CHIP = PD,QUIESCENT + nPD, OUTPUT − nPDQ, OUTPUT
PD, ON-CHIP = 2.3 W + 0.45 W − 0.25 W = 2.5 W
(7)
For each disabled RGB output channel, the quiescent power supply
current in VPOS and VNEG drops by approximately 34 mA.
From Figure 51 or Equation 1, this power dissipation is below
the maximum allowed dissipation for all ambient temperatures
up to, and including, 85°C.
Rev. 0 | Page 33 of 40
AD8177
In a general case, the power delivered by the digital supply and
dissipated into the digital output devices has to be taken into
account following a similar derivation. However, because the
loads driven by the H and V outputs are high and because the
voltage at these outputs typically sits close to either rail, the
correction to the on-chip power estimate is small. Furthermore,
the H and V outputs are active only briefly during sync genera-
tion and are returned to digital ground thereafter.
All these sources of crosstalk are vector quantities, so the magni-
tudes cannot simply be added together to obtain the total crosstalk.
In fact, there are conditions where driving additional circuits in
parallel in a given configuration can actually reduce the crosstalk.
The fact that the AD8177 is a fully differential design means that
many sources of crosstalk either destructively cancel, or are
common mode to, the signal and can be rejected by a differential
receiver.
Short-Circuit Output Conditions
Areas of Crosstalk
Although there is short-circuit current protection on the AD8177
outputs, the output current can reach values of 80 mA into
a grounded output. Any sustained operation with too many
shorted outputs can exceed the maximum die temperature
and can result in device failure (see the Absolute Maximum
Ratings section).
A practical AD8177 circuit must be mounted to an actual circuit
board to connect it to power supplies and measurement equipment.
Great care has been taken to create an evaluation board (available
upon request) that adds minimum crosstalk to the intrinsic device.
This, however, raises the issue that system crosstalk is a combi-
nation of the intrinsic crosstalk of the devices, in addition to the
circuit board to which they are mounted. It is important to try
to separate these two areas when attempting to minimize the
effect of crosstalk.
Crosstalk
Many systems (such as KVM switches) that handle numerous
analog signal channels have strict requirements for keeping the
various signals from influencing any of the other signals in the
system. Crosstalk is the term used to describe the coupling of
the signals of other nearby channels to a given channel.
In addition, crosstalk can occur among the inputs to a crosspoint
and among the outputs. It can also occur from input to output.
The following sections discuss techniques to diagnose which
part of a system is contributing to crosstalk.
When there are many signals in close proximity in a system, as
is undoubtedly the case in a system that uses the AD8177, the
crosstalk issues can be quite complex. A good understanding of
the nature of crosstalk and some definition of terms is required
to specify a system that uses one or more crosspoint devices.
Measuring Crosstalk
Crosstalk is measured by applying a signal to one or more
channels and measuring the relative strength of that signal on a
desired selected channel. The measurement is usually expressed
as decibels (dB) down from the magnitude of the test signal.
The crosstalk is expressed by
Types of Crosstalk
Crosstalk can be propagated by means of any of three methods.
These fall into the categories of electric field, magnetic field,
and the sharing of common impedances. This section explains
these effects.
⎛
⎜
⎞
⎟
A
SEL (s)
XT = 20 log10
(8)
⎜
⎝
⎟
⎠
ATEST (s)
where:
Every conductor can be both a radiator of electric fields and a
receiver of electric fields. The electric field crosstalk mechanism
occurs when the electric field created by the transmitter propagates
across a stray capacitance (for example, free space) and couples
with the receiver and induces a voltage. This voltage is an
unwanted crosstalk signal in any channel that receives it.
s = jω, the Laplace transform variable.
ASEL(s) is the amplitude of the crosstalk induced signal in the
selected channel.
ATEST(s) is the amplitude of the test signal.
It can be seen that crosstalk is a function of frequency but not
a function of the magnitude of the test signal (to first order).
In addition, the crosstalk signal has a phase relative to the test
Currents flowing in conductors create magnetic fields that
circulate around the currents. These magnetic fields then
generate voltages in any other conductors whose paths they
link. The undesired induced voltages in these other channels are
crosstalk signals. The channels that crosstalk can be said to have
a mutual inductance that couples signals from one channel to
another.
signal associated with it.
A network analyzer is most commonly used to measure
crosstalk over a frequency range of interest. It can provide both
magnitude and phase information about the crosstalk signal.
As a crosspoint system or device grows larger, the number of
theoretical crosstalk combinations and permutations can
become extremely large.
The power supplies, grounds, and other signal return paths of
a multichannel system are generally shared by the various channels.
When a current from one channel flows in one of these paths,
a voltage that is developed across the impedance becomes an
input crosstalk signal for other channels that share the common
impedance.
Rev. 0 | Page 34 of 40
AD8177
For example, in the case of the triple 16 × 5 matrix of the AD8177,
we can look at the number of crosstalk terms that can be
considered for a single channel, such as Input Channel INPUT0.
INPUT0 is programmed to connect to one of the AD8177
outputs where the measurement can be made.
of-phase fields. In the case of driving low impedance video loads,
output inductances contribute highly to output crosstalk.
The flexible programming capability of the AD8177 can be used
to diagnose whether crosstalk is occurring more on the input
side or the output side. Some examples are illustrative. A given
input channel (INPUT7, roughly in the middle for this example)
can be programmed to drive OUTPUT2 (exactly in the middle).
The inputs to INPUT7 are just terminated to ground (via 50 ꢀ
or 75 ꢀ), and no signal is applied.
First, the crosstalk terms associated with driving a test signal into
each of the other 15 input channels can be measured one at a
time, while applying no signal to INPUT0. Then, the crosstalk
terms associated with driving a parallel test signal into all 15 other
inputs can be measured two at a time in all possible combinations,
then three at a time, and so on, until, finally, there is only one
way to drive a test signal into all 15 other input channels in
parallel.
All the other inputs are driven in parallel with the same test signal
(practically provided by a distribution amplifier), with all other
outputs except OUTPUT2 disabled. Because grounded INPUT7
is programmed to drive OUTPUT2, no signal should be present.
Any signal that is present can be attributed to the other 15 hostile
input signals because no other outputs are driven (they are all
disabled). Thus, this method measures the all-hostile input
contribution to crosstalk into INPUT7. Of course, the method
can be used for other input channels and combinations of
hostile inputs.
Each of these cases is legitimately different from the others and
might yield a unique value, depending on the resolution of the
measurement system; but it is hardly practical to measure all
these terms and then specify them. In addition, this describes
the crosstalk matrix for just one input channel. A similar crosstalk
matrix can be proposed for every other input. In addition, if the
possible combinations and permutations for connecting inputs
to the other outputs (not used for measurement) are taken into
consideration, the numbers rather quickly grow to astronomical
proportions. If a larger crosspoint array of multiple AD8177s is
constructed, the numbers grow larger still.
For output crosstalk measurement, a single input channel is
driven (INPUT0, for example) and all outputs other than a given
output (OUTPUT2 in the middle) are programmed to connect
to INPUT0. OUTPUT2 is programmed to connect to INPUT15
(far away from INPUT0), which is terminated to ground. Thus,
OUTPUT2 should not have a signal present because it is listening
to a quiet input. Any signal measured at the OUTPUT2 can be
attributed to the output crosstalk of the other four hostile outputs.
Again, this method can be modified to measure other channels
and other crosspoint matrix combinations.
Obviously, some subset of all these cases must be selected to be
used as a guide for a practical measure of crosstalk. One common
method is to measure all hostile crosstalk; this means that the
crosstalk to the selected channel is measured while all other system
channels are driven in parallel. In general, this yields the worst
crosstalk number, but this is not always the case, due to the
vector nature of the crosstalk signal.
Effect of Impedances on Crosstalk
The input side crosstalk can be influenced by the output imped-
ance of the sources that drive the inputs. The lower the impedance
of the drive source, the lower the magnitude of the crosstalk.
The dominant crosstalk mechanism on the input side is capacitive
coupling. The high impedance inputs do not have significant
current flow to create magnetically induced crosstalk. However,
significant current can flow through the input termination
resistors and the loops that drive them. Thus, the PC board on
the input side can contribute to magnetically coupled crosstalk.
Other useful crosstalk measurements are those created by one
nearest neighbor or by the two nearest neighbors on either side.
These crosstalk measurements are generally higher than those
of more distant channels, so they can serve as a worst-case
measure for any other one-channel or two-channel crosstalk
measurements.
Input and Output Crosstalk
Capacitive coupling is voltage-driven (dV/dt) but is generally
a constant ratio. Capacitive crosstalk is proportional to input or
output voltage, but this ratio is not reduced by simply reducing
signal swings. Attenuation factors must be changed by changing
impedances (lowering mutual capacitance), or destructive
canceling must be utilized by summing equal and out-of-phase
components. For high input impedance devices such as the
AD8177, capacitances generally dominate input-generated
crosstalk.
From a circuit standpoint, the input crosstalk mechanism looks
like a capacitor coupling to a resistive load. For low frequencies,
the magnitude of the crosstalk is given by
XT = 20 log10
where:
RS is the source resistance.
(RSCM ) × s
]
(9)
CM is the mutual capacitance between the test signal circuit and
the selected circuit.
s is the Laplace transform variable.
Inductive coupling is proportional to current (dI/dt) and often
scales as a constant ratio with signal voltage, but it also shows
a dependence on impedances (load current). Inductive coupling
can also be reduced by constructive canceling of equal and out-
Rev. 0 | Page 35 of 40
AD8177
From Equation 9, it can be observed that this crosstalk mechanism
has a high-pass nature; it can also be minimized by reducing the
coupling capacitance of the input circuits and lowering the output
impedance of the drivers. If the input is driven from a 75 ꢀ
terminated cable, the input crosstalk can be reduced by buffering
this signal with a low output impedance buffer.
PCB Termination Layout
As frequencies of operation increase, the importance of proper
transmission line signal routing becomes more important. The
bandwidth of the AD8177 is large enough that using high imped-
ance routing does not provide a flat in-band frequency response
for practical signal trace lengths. It is necessary for the user to
choose a characteristic impedance suitable for the application and
properly terminate the input and output signals of the AD8177.
Traditionally, video applications have used 75 ꢀ single-ended
environments. RF applications are generally 50 ꢀ single-ended
(and board manufacturers have the most experience with this
application). Cat-5 cabling is usually driven as differential pairs of
100 ꢀ differential impedance.
On the output side, the crosstalk can be reduced by driving
a lighter load. Although the AD8177 is specified with excellent
settling time when driving a properly terminated Cat-5, the
crosstalk is higher than the minimum obtainable, due to the high
output currents. These currents induce crosstalk via the mutual
inductance of the output pins and bond wires of the AD8177.
From a circuit standpoint, this output crosstalk mechanism looks
like a transformer with a mutual inductance between the windings
that drives a load resistor. For low frequencies, the magnitude of
the crosstalk is given by
For flexibility, the AD8177 does not contain on-chip termina-
tion resistors. This flexibility in application comes with some
board layout challenges. The distance between the termination
of the input transmission line and the AD8177 die is a high
impedance stub and causes reflections of the input signal. With
some simplification, it can be shown that these reflections cause
peaking of the input at regular intervals in frequency, dependent
on the propagation speed (VP) of the signal in the chosen board
material and the distance (d) between the termination resistor
and the AD8177. If the distance is great enough, these peaks
can occur in-band. In fact, practical experience shows that these
peaks are not high-Q, and should be pushed out to three or four
times the desired bandwidth to not have an effect on the signal.
For a board designer using FR4 (VP = 144 × 106 m/s), this means
the AD8177 should be no more than 1.5 cm after the termination
resistors; preferably, it should be placed even closer. The BGA
substrate routing inside the AD8177 is approximately 1 cm in
length and adds to the stub length, so 1.5 cm PCB routing
equates to d = 2.5 × 10–2 m in the calculations.
⎛
⎜
⎝
⎞
⎟
⎟
⎠
s
⎜
XT = 20 log10 MXY
×
(10)
RL
where:
MXY is the mutual inductance of Output X to Output Y.
RL is the load resistance on the measured output.
This crosstalk mechanism can be minimized by keeping the
mutual inductance low and increasing RL. The mutual inductance
can be kept low by increasing the spacing of the conductors and
minimizing their parallel length.
PCB Layout
Extreme care must be exercised to minimize additional crosstalk
generated by the system circuit board(s). The areas that must
be carefully detailed are grounding, shielding, signal routing,
and supply bypassing.
(
2n + 1 VP
)
Packaging of the AD8177 is designed to help keep crosstalk to
a minimum. On the PBGA substrate, each pair is carefully routed
to predominately couple to each other, with shielding traces
separating adjacent signal pairs. The ball grid array is arranged
such that similar board routing can be achieved. Input and output
differential pairs are grouped by channel rather than by color to
allow for easy, convenient board routing.
fPEAK
=
(11)
4d
where n = {0, 1, 2, 3, ...}.
In some cases, it is difficult to place the termination close to the
AD8177 due to space constraints, differential routing, and large
resistor footprints. A preferable solution in this case is to main-
tain a controlled transmission line past the AD8177 inputs and
terminate the end of the line. This is known as fly-by termination.
The input impedance of the AD8177 is large enough, and stub
length inside the package is small enough that this works well
in practice. Implementation of fly-by input termination often
includes bringing the signal in on one routing layer, then passing
through a filled via under the AD8177 input ball, then back out
to termination on another signal layer. In this case, care must be
taken to tie the reference ground planes together near the signal
via if the signal layers are referenced to different ground planes.
The input and output signals have minimum crosstalk if they
are located between ground planes on layers above and below
and separated by ground in between. Vias should be located as
close to the IC as possible to carry the inputs and outputs to the
inner layer. The input and output signals surface at the input
termination resistors and the output series back-termination
resistors. To the extent possible, these signals should also be
separated as soon as they emerge from the IC package.
Rev. 0 | Page 36 of 40
AD8177
One solution is to adjust the trace width to create a transmission
AD8177
line of half the characteristic impedance and terminate the far
end with this resistance (25 ꢀ in a 50 ꢀ system). This is not
often practical as trace widths become large. In most cases, the
best practical solution is to place the half-characteristic impedance
resistor as close as possible (preferably less than 1.5 cm away)
and to reduce the parasitics of the stub (by removing the ground
plane under the stub, for example). In either case, the designer
must decide if the layout complexity created by a balanced,
terminated solution is preferable to simply grounding the undriven
input at the ball with no trace.
OPn
ONn
IPn
INn
50Ω
Figure 53. Fly-By Input Termination
(Grounds for the two transmission lines shown
must be tied together close to the INn pin.)
If multiple AD8177s are to be driven in parallel, a fly-by input
termination scheme is very useful, but the distance from each
AD8177 input to the driven input transmission line is a stub
that should be minimized in length and parasitics using the
discussed guidelines.
The examples discussed so far are for input termination, but the
theory is similar for output back-termination. Taking the AD8177
as an ideal voltage source, any distance of routing between the
AD8177 and a back-termination resistor is an impedance
mismatch that potentially creates reflections. For this reason,
back-termination resistors should also be placed close to the
AD8177. In practice, because back-termination resistors are
series elements, they can be placed close to the AD8177 outputs.
When driving the AD8177 single-endedly, the undriven input is
often terminated with a resistance to balance the input stage.
By terminating the undriven input with a resistor of one-half
the characteristic impedance, the input stage is perfectly balanced
(25 ꢀ, for example, to balance the two parallel 50 ꢀ terminations
on the driven input). However, due to the feedback in the input
receiver, there is high speed signal current leaving the undriven
input. To terminate this high speed signal, proper transmission
line techniques should be used.
Finally, the AD8177 pinout allows the user to bring the outputs
out as surface traces to the back-termination resistors. The
designer can avoid creating stubs and reflections by keeping the
AD8177 output signal path on the surface of the board. A stub
is created when a top-to-bottom via connection is made on the
output signal path that is perpendicular to the signal flow.
Rev. 0 | Page 37 of 40
AD8177
VPOS
VDD
FOUR AD8147
(G = +2)
AD8003
(G = +4)
FOUR 15-PIN HD
CONNECTORS
15-PIN HD
CONNECTOR
THREE 15-PIN HD
CONNECTORS
THREE RGB, HV
CHANNELS
FOUR RGB, HV
CHANNELS
RGB
MONITOR
PC
OUT0 TO OUT1
IN0 TO IN3
THREE 15-PIN HD
CONNECTORS
THREE RGB, HV
CHANNELS
FOUR DIFFERENTIAL
RGB WITH SYNC-ON
CM CHANNELS
FOUR AD8147
(G = +2)
RGB
MONITOR
THREE RGB
CHANNELS
FOUR 15-PIN HD
CONNECTORS
OUT2
15-PIN HD
CONNECTOR
FOUR RGB, HV
CHANNELS
THREE HV
PAIRS
RJ-45
PC
IN0 TO IN3
OUT0 TO OUT1
OUT2
CONNECTOR
IN4 TO IN7
THREE RGB, HV
CHANNELS
RGB, HV
CHANNEL
AD8145
(G = +2)
IN4 TO IN7
IN8 TO IN11
IN12 TO IN13
IN14 TO IN15
OUT3
DIFFERENTIAL
OFFSET
DIFFERENTIAL
RGB WITH
SYNC-ON CM
CAT-5
OUT3
15-PIN HD
CONNECTORS
RGB
MONITOR
OUT4
RJ-45
CONNECTOR
AD8177 DUT
CAT5
PC
IN8 TO IN11
FOUR RJ-45
CONNECTORS
RGB, HV
CHANNEL
TWO
AD8147 (G = +2)
EVALUATION BOARD
DIFFERENTIAL
RGB CHANNELS
TWELVE SMA
CONNECTORS
DIFFERENTIAL
RGB, HV
CHANNEL
SIGNAL GENERATOR/
NETWORK ANALYZER
IN12 TO IN13
GORE
HEADER
RIBBON CABLE
OUT4
IN14 TO IN15
NATIONAL
INSTRUMENTS
CONTROLLER BOARD
TWO GORE
HEADERS
USB
AD8177
CUSTOMER
EVALUATION BOARD
GND
VNEG
TO CONTROLLER PC USB
Figure 54. Evaluation Board Block Diagram
Rev. 0 | Page 38 of 40
AD8177
OUTLINE DIMENSIONS
27.20
27.00 SQ
26.80
A1 CORNER
INDEX AREA
26 24 22 20 18 16 14 12 10
25 23 21 19 17 15 13 11
8
6
4
2
9
7
5
3
1
A
B
C
D
E
F
A1 BALL
PAD CORNER
G
H
J
K
24.20
24.00 SQ
23.80
L
M
N
TOP VIEW
P
R
T
U
V
W
Y
1.00
BSC
AA
AB
AC
AD
AE
AF
2.43
2.32
2.15
DETAIL A
1.19
1.17
1.15
DETAIL A
0.60
0.55
0.50
COPLANARITY
0.20 MAX
0.70
0.60
0.50
0.70
0.60
0.50
SEATING
PLANE
BALL DIAMETER
COMPLIANT TO JEDEC STANDARDS MS-034-AAL-1
Figure 55. 676-Ball Plastic Ball Grid Array [PBGA]
(B-676)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option
AD8177ABPZ1
AD8177-EVALZ1
−40°C to +85°C
676-Ball Plastic Ball Grid Array [PBGA]
Evaluation Board
B-676
1 Z = RoHS Compliant Part.
Rev. 0 | Page 39 of 40
AD8177
NOTES
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06605-0-7/07(0)
Rev. 0 | Page 40 of 40
相关型号:
©2020 ICPDF网 联系我们和版权申明