AD811JR-REEL [ADI]
High Performance Video Op Amp; 高性能视频运算放大器型号: | AD811JR-REEL |
厂家: | ADI |
描述: | High Performance Video Op Amp |
文件: | 总15页 (文件大小:233K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
High Performance
Video Op Amp
a
AD811
CONNECTION DIAGRAMS
FEATURES
High Speed
20-Lead LCC (E-20A) Package
8-Lead Plastic (N-8)
Cerdip (Q-8)
SOIC (SO-8) Packages
140 MHz Bandwidth (3 dB, G = +1)
120 MHz Bandwidth (3 dB, G = +2)
35 MHz Bandwidth (0.1 dB, G = +2)
2500 V/s Slew Rate
25 ns Settling Time to 0.1% (For a 2 V Step)
65 ns Settling Time to 0.01% (For a 10 V Step)
Excellent Video Performance (RL =150 ⍀)
0.01% Differential Gain, 0.01؇ Differential Phase
Voltage Noise of 1.9 nV√Hz
20
1
2
19
3
NC 4
18 NC
17
NC
–IN
+IN
NC
+V
1
2
3
4
8
7
6
5
5
6
7
NC
–IN
NC
NC
16 +V
AD811
S
S
15 NC
OUTPUT
NC
+IN 8
14 OUTPUT
–V
S
AD811
9
10 1112 13
NC = NO CONNECT
NC = NO CONNECT
Low Distortion: THD = –74 dB @ 10 MHz
Excellent DC Precision
3 mV max Input Offset Voltage
Flexible Operation
Specified for ؎5 V and ؎15 V Operation
؎2.3 V Output Swing into a 75 ⍀ Load (VS = ؎5 V)
16-Lead SOIC (R-16) Package 20-Lead SOIC (R-20) Package
NC
NC
NC
–IN
NC
+IN
NC
1
2
3
4
5
6
7
8
20
19
18
NC
NC
NC
+V
1
2
3
4
16 NC
15 NC
NC
NC
+V
14
–IN
NC
S
APPLICATIONS
Video Crosspoint Switchers, Multimedia Broadcast
Systems
HDTV Compatible Systems
Video Line Drivers, Distribution Amplifiers
ADC/DAC Buffers
DC Restoration Circuits
Medical—Ultrasound, PET, Gamma and Counter
Applications
17
16
13 NC
12
S
NC
+IN
NC
5
6
7
8
OUTPUT
15 OUTPUT
14 NC
11 NC
10
9
–V
S
NC
NC
AD811
–V
S
NC
NC
13
12
11
NC
NC
NC
9
NC = NO CONNECT
AD811
10
NC
NC = NO CONNECT
PRODUCT DESCRIPTION
The AD811 is also excellent for pulsed applications where tran-
sient response is critical. It can achieve a maximum slew rate of
greater than 2500 V/µs with a settling time of less than 25 ns to
0.1% on a 2 volt step and 65 ns to 0.01% on a 10 volt step.
The AD811 is a wideband current-feedback operational ampli-
fier, optimized for broadcast quality video systems. The –3 dB
bandwidth of 120 MHz at a gain of +2 and differential gain and
phase of 0.01% and 0.01° (RL = 150 Ω) make the AD811 an
excellent choice for all video systems. The AD811 is designed to
meet a stringent 0.1 dB gain flatness specification to a band-
width of 35 MHz (G = +2) in addition to the low differential
gain and phase errors. This performance is achieved whether
driving one or two back terminated 75 Ω cables, with a low
power supply current of 16.5 mA. Furthermore, the AD811 is
specified over a power supply range of ±4.5 V to ±18 V.
The AD811 is ideal as an ADC or DAC buffer in data acquisi-
tion systems due to its low distortion up to 10 MHz and its wide
unity gain bandwidth. Because the AD811 is a current feedback
amplifier, this bandwidth can be maintained over a wide range
of gains. The AD811 also offers low voltage and current noise of
1.9 nV/√Hz and 20 pA/√Hz, respectively, and excellent dc accu-
racy for wide dynamic range applications.
12
0.20
0.10
G = +2
0.18
0.09
RF = 649⍀
RL = 150⍀
9
6
3
VS = ؎15V
FC = 3.58MHz
100 IRE
RG = RFB
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0.02
0.08
0.07
MODULATED RAMP
RL = 150⍀
0.06
0.05
0.04
0.03
0.02
0.01
VS = ؎5V
PHASE
0
–3
–6
GAIN
6
1M
10M
FREQUENCY – Hz
100M
5
7
8
9
10 11 12 13 14 15
SUPPLY VOLTAGE – Volts
؎
REV. D
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
World Wide Web Site: http://www.analog.com
© Analog Devices, Inc., 1999
(@ TA = +25؇C and VS = ؎15 V dc, RLOAD = 150 Ω unless otherwise noted)
AD811–SPECIFICATIONS
AD811J/A1
Typ
AD811S2
Typ
Model
Conditions
VS
Min
Max
Min
Max
Units
DYNAMIC PERFORMANCE
Small Signal Bandwidth (No Peaking)
–3 dB
G = +1
G = +2
G = +2
G = +10
0.1 dB Flat
G = +2
RFB = 562 Ω
RFB = 649 Ω
RFB = 562 Ω
RFB = 511 Ω
±15 V
±15 V
±5 V
140
120
80
140
120
80
MHz
MHz
MHz
MHz
±15 V
100
100
RFB = 562 Ω
RFB = 649 Ω
VOUT = 20 V p-p
VOUT = 4 V p-p
VOUT = 20 V p-p
10 V Step, AV = –1
±5 V
25
35
40
400
2500
50
65
25
3.5
0.01
0.01
–74
36
25
35
40
400
2500
50
65
25
3.5
0.01
0.01
–74
36
MHz
MHz
MHz
V/µs
V/µs
ns
ns
ns
ns
%
Degree
dBc
dBm
dBm
±15 V
±15 V
±5 V
±15 V
±15 V
Full Power Bandwidth3
Slew Rate
Settling Time to 0.1%
Settling Time to 0.01%
Settling Time to 0.1%
Rise Time, Fall Time
Differential Gain
2 V Step, AV = –1
RFB = 649, AV = +2
f = 3.58 MHz
f = 3.58 MHz
VOUT = 2 V p-p, AV = +2
@ fC = 10 MHz
±5 V
±15 V
±15 V
±15 V
±15 V
±5 V
Differential Phase
THD @ fC = 10 MHz
Third Order Intercept4
±15 V
43
43
INPUT OFFSET VOLTAGE
Offset Voltage Drift
±5 V, ±15 V
0.5
3
5
0.5
3
5
mV
mV
µV/°C
TMIN to TMAX
5
5
INPUT BIAS CURRENT
–Input
±5 V, ±15 V
±5 V, ±15 V
2
2
5
2
2
5
µA
µA
µA
µA
TMIN to TMAX
TMIN to TMAX
15
10
20
30
10
25
+Input
TRANSRESISTANCE
TMIN to TMAX
VOUT = ±10 V
RL = ∞
±15 V
±15 V
0.75
0.5
1.5
0.75
0.75
0.5
1.5
0.75
MΩ
MΩ
RL = 200 Ω
VOUT = ±2.5 V
RL = 150 Ω
±5 V
0.25
0.4
0.125 0.4
MΩ
COMMON-MODE REJECTION
VOS (vs. Common Mode)
TMIN to TMAX
TMIN to TMAX
Input Current (vs. Common Mode)
VCM = ±2.5
VCM = ±10 V
TMIN to TMAX
±5 V
±15 V
56
60
60
66
1
50
56
60
66
1
dB
dB
µA/V
3
3
POWER SUPPLY REJECTION
VOS
+Input Current
–Input Current
VS = ±4.5 V to ±18 V
TMIN to TMAX
TMIN to TMAX
60
70
0.3
0.4
60
70
0.3
0.4
dB
µA/V
µA/V
2
2
2
2
TMIN to TMAX
INPUT VOLTAGE NOISE
INPUT CURRENT NOISE
f = 1 kHz
f = 1 kHz
1.9
20
1.9
20
nV/√Hz
pA/√Hz
OUTPUT CHARACTERISTICS
Voltage Swing, Useful Operating Range5
±5 V
±15 V
±2.9
±12
100
150
9
±2.9
±12
100
150
9
V
V
mA
mA
Ω
Output Current
Short-Circuit Current
Output Resistance
TJ = +25°C
(Open Loop @ 5 MHz)
INPUT CHARACTERISTICS
+Input Resistance
–Input Resistance
1.5
14
1.5
14
MΩ
Ω
Input Capacitance
Common-Mode Voltage Range
+Input
7.5
±3
7.5
±3
pF
V
±5 V
±15 V
±13
±13
V
POWER SUPPLY
Operating Range
Quiescent Current
±4.5
±18
16.0
18.0
±4.5
±18
16.0
18.0
V
mA
mA
±5 V
±15 V
14.5
16.5
14.5
16.5
TRANSISTOR COUNT
NOTES
# of Transistors
40
40
1The AD811JR is specified with ± 5 V power supplies only, with operation up to ±12 volts.
2See Analog Devices’ military data sheet for 883B tested specifications.
3FPBW = slew rate/(2 π VPEAK).
4Output power level, tested at a closed loop gain of two.
5Useful operating range is defined as the output voltage at which linearity begins to degrade.
Specifications subject to change without notice.
REV. D
–2–
AD811
ABSOLUTE MAXIMUM RATINGS1
MAXIMUM POWER DISSIPATION
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±18 V
AD811JR Grade Only . . . . . . . . . . . . . . . . . . . . . . . . .±12 V
Internal Power Dissipation2 . . . . . . . . Observe Derating Curves
Output Short Circuit Duration . . . . . Observe Derating Curves
Common-Mode Input Voltage . . . . . . . . . . . . . . . . . . . . . ±VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . .±6 V
Storage Temperature Range (Q, E) . . . . . . . . –65°C to +150°C
Storage Temperature Range (N, R) . . . . . . . . –65°C to +125°C
Operating Temperature Range
AD811J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0°C to +70°C
AD811A . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
AD811S . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to +125°C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300°C
The maximum power that can be safely dissipated by the
AD811 is limited by the associated rise in junction temperature.
For the plastic packages, the maximum safe junction tempera-
ture is +145°C. For the cerdip and LCC packages, the maxi-
mum junction temperature is +175°C. If these maximums are
exceeded momentarily, proper circuit operation will be restored
as soon as the die temperature is reduced. Leaving the device in
the “overheated” condition for an extended period can result in
device burnout. To ensure proper operation, it is important to
observe the derating curves in Figures 17 and 18.
While the AD811 is internally short circuit protected, this may
not be sufficient to guarantee that the maximum junction tem-
perature is not exceeded under all conditions. One important
example is when the amplifier is driving a reverse terminated
75 Ω cable and the cable’s far end is shorted to a power supply.
With power supplies of ±12 volts (or less) at an ambient tem-
perature of +25°C or less, if the cable is shorted to a supply rail,
then the amplifier will not be destroyed, even if this condition
persists for an extended period.
NOTES
1Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
28-Lead Plastic Package: θJA = 90°C/W
8-Lead Cerdip Package: θJA = 110°C/W
8-Lead SOIC Package: θJA = 155°C/W
16-Lead SOIC Package: θJA = 85°C/W
ESD SUSCEPTIBILITY
20-Lead SOIC Package: θJA = 80°C/W
20-Lead LCC Package: θJA = 70°C/W
ESD (electrostatic discharge) sensitive device. Electrostatic
charges as high as 4000 volts, which readily accumulate on the
human body and on test equipment, can discharge without
detection. Although the AD811 features proprietary ESD pro-
tection circuitry, permanent damage may still occur on these
devices if they are subjected to high energy electrostatic dis-
charges. Therefore, proper ESD precautions are recommended
to avoid any performance degradation or loss of functionality.
ORDERING GUIDE
Temperature
Range
Package
Option*
Model
AD811AN
AD811AR-16
AD811AR-20
AD811JR
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
0°C to +70°C
N-8
R-16
R-20
SO-8
Q-8
METALIZATION PHOTOGRAPH
Contact Factory for Latest Dimensions.
Dimensions Shown in Inches and (mm).
AD811SQ/883B
5962-9313101MPA
AD811SE/883B
5962-9313101M2A
AD811JR-REEL
AD811JR-REEL7
AD811AR-16-REEL
AD811AR-16-REEL7
AD811AR-20-REEL
AD811ACHIPS
AD811SCHIPS
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
0°C to +70°C
Q-8
E-20A
E-20A
SO-8
SO-8
R-16
R-16
R-20
Die
0°C to +70°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–55°C to +125°C
Die
*E = Ceramic Leadless Chip Carrier; N = Plastic DIP; Q = Cerdip; SO (R) =
Small Outline IC (SOIC).
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD811 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. D
–3–
AD811–Typical Performance Characteristics
20
20
15
10
T
= +25؇C
A
T
= +25؇C
A
15
10
NO LOAD
R
= 150⍀
L
5
0
5
0
0
5
10
SUPPLY VOLTAGE – ؎Volts
15
20
0
5
10
SUPPLY VOLTAGE – ؎ Volts
15
20
Figure 1. Input Common-Mode Voltage Range vs. Supply
Figure 4. Output Voltage Swing vs. Supply
35
30
21
18
V
= ؎15V
S
25
20
15
V
= ؎15V
15
S
12
9
V
= ؎5V
S
V
= ؎5V
S
10
5
6
0
3
10
100
1k
10k
–60 –40 –20
0
20
60
120 140
40
80
100
LOAD RESISTANCE – ⍀
JUNCTION TEMPERATURE – ؇C
Figure 2. Output Voltage Swing vs. Resistive Load
Figure 5. Quiescent Supply Current vs. Junction
Temperature
10
10
8
NONINVERTING INPUT
؎5 TO ؎15V
6
4
V
= ؎5V
S
0
V
= ؎5V
S
INVERTING
INPUT
2
–10
–20
–30
0
–2
–4
–6
V
= ؎15V
S
V
= ؎15V
S
–8
–10
–60 –40 –20
0
20
40
60
80
100 120 140
–60 –40 –20
0
20
40
60
80
100 120 140
JUNCTION TEMPERATURE – ؇C
JUNCTION TEMPERATURE – ؇C
Figure 3. Input Bias Current vs. Junction Temperature
Figure 6. Input Offset Voltage vs. Junction Temperature
–4–
REV. D
AD811
2.0
1.5
1.0
250
200
150
V
= ؎15V
= 200⍀
S
R
V
L
= ؎10V
OUT
V
= ؎15V
S
0.5
0
V
= ؎5V
V
= ؎5V
100
50
S
S
R
V
= 150⍀
L
= ؎2.5V
OUT
–60 –40 –20
0
20
40
60
80
100 120 140
–60
–40 –20
0
20
40
60
80
100 120 140
JUNCTION TEMPERATURE – ؇C
JUNCTION TEMPERATURE – ؇C
Figure 10. Transresistance vs. Junction Temperature
Figure 7. Short Circuit Current vs. Junction Temperature
100
10
1
10
100
10
1
NONINVERTING CURRENT V = ؎5 TO 15V
S
V
= ؎5V
S
1
INVERTING CURRENT V = ؎5 TO 15V
S
0.1
V
= ؎15V
S
VOLTAGE NOISE V = ؎15V
S
GAIN = +2
= 649⍀
R
FB
VOLTAGE NOISE V = ؎5V
S
0.01
10k
100k
1M
10M
100M
100
1k
10k
100k
10
FREQUENCY – Hz
FREQUENCY – Hz
Figure 11. Input Noise vs. Frequency
Figure 8. Closed-Loop Output Resistance vs. Frequency
200
10
8
10
V
= 1V p–p
RISE TIME
O
V = ؎15V
160
120
80
40
0
S
8
6
4
2
60
40
20
0
R = 150⍀
L
GAIN = +2
6
BANDWIDTH
V
V
= ؎15V
= 1V p–p
= 150⍀
S
OVERSHOOT
O
4
R
L
GAIN = +2
2
0
PEAKING
800
0
400
400
600
1.0k
1.2k
1.4k
1.6k
600
1.0k
1.2k
1.4k
1.6k
800
VALUE OF FEEDBACK RESISTOR (R ) – ⍀
FB
VALUE OF FEEDBACK RESISTOR (R ) – ⍀
FB
Figure 12. 3 dB Bandwidth and Peaking vs. Value of RFB
Figure 9. Rise Time and Overshoot vs. Value of
Feedback Resistor, RFB
REV. D
–5–
AD811
110
100
90
25
20
15
10
649⍀
649⍀
150⍀
V
V
OUT
IN
V
= ؎15V
S
150⍀
80
GAIN = +10
OUTPUT LEVEL FOR 3% THD
70
V
= ؎15V
S
60
V
= ؎5V
S
50
V
= ؎5V
S
5
0
40
30
1k
10k
100k
FREQUENCY – Hz
1M
10M
100k
1M
10M
100M
FREQUENCY – Hz
Figure 13. Common-Mode Rejection vs. Frequency
Figure 16. Large Signal Frequency Response
80
–50
V
= 2V p–p
OUT
V
= ؎15V
= ؎5V
R
A
= 649⍀
S
70
60
50
40
30
20
10
5
F
R
= 100⍀
L
= +2
V
GAIN = +2
–70
–90
؎5V SUPPLIES
V
S
CURVES ARE FOR WORST
CASE CONDITION WHERE
ONE SUPPLY IS VARIED
WHILE THE OTHER IS
HELD CONSTANT.
2ND HARMONIC
3RD HARMONIC
؎15V SUPPLIES
–110
–130
2ND HARMONIC
3RD HARMONIC
1k
10k
100k
1M
10M
1k
10k
100k
1M
10M
FREQUENCY – Hz
FREQUENCY – Hz
Figure 14. Power Supply Rejection vs. Frequency
Figure 17. Harmonic Distortion vs. Frequency
2.5
3.4
3.2
T
MAX = +145؇C
J
3.0
2.8
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
0.8
T
MAX = +175؇C
J
16-LEAD SOIC
2.0
1.5
1.0
0.5
20-LEAD LCC
20-LEAD SOIC
8-LEAD MINI-DIP
8-LEAD CERDIP
8-LEAD SOIC
0.6
0.4
–50 –40 –30 –20 –10
0
10 20 30 40 50 60 70 80 90
–60 –40 –20
0
20
40
60
80
100 120 140
AMBIENT TEMPERATURE – ؇C
AMBIENT TEMPERATURE – ؇C
Figure 15. Maximum Power Dissipation vs. Temperature
for Plastic Packages
Figure 18. Maximum Power Dissipation vs. Temperature
for Hermetic Packages
–6–
REV. D
Typical Characteristics, Noninverting Connection–AD811
9
G = +1
R
FB
R
R
= 150⍀
6
3
L
=
G
+V
S
V
= ؎15V
= 750⍀
S
R
V
TO
FB
OUT
0.1F
TEKTRONIX
P6201 FET
PROBE
R
G
0
AD811
+
V
–3
–6
–9
–12
IN
R
L
V
= ؎5V
S
HP8130
PULSE
GENERATOR
50⍀
R
= 619⍀
FB
–V
0.1F
S
1M
10M
FREQUENCY – Hz
100M
Figure 22. Closed-Loop Gain vs. Frequency, Gain = +1
Figure 19. Noninverting Amplifier Connection
26
1V
G = +10
10ns
V
R
= ؎15V
S
23
20
17
14
11
8
R
= 150⍀
L
= 511⍀
FB
100
90
V
IN
V
R
= ؎5V
= 442⍀
S
FB
10
V
OUT
0%
1V
1M
10M
FREQUENCY – Hz
100M
Figure 20. Small Signal Pulse Response, Gain = +1
Figure 23. Closed-Loop Gain vs. Frequency, Gain = +10
100mV
10ns
1V
20ns
100
90
100
90
V
IN
V
IN
10
10
V
OUT
V
OUT
0%
0%
1V
10V
Figure 21. Small Signal Pulse Response, Gain = +10
Figure 24. Large Signal Pulse Response, Gain = +10
REV. D
–7–
AD811–Typical Characteristics, Inverting Connection
6
R
FB
V
R
= ؎15V
= 590⍀
S
G = –1
R = 150⍀
L
+V
3
0
FB
S
0.1F
V
TO
OUT
TEKTRONIX
P6201 FET
PROBE
R
V
G
IN
–3
–6
–9
–12
HP8130
PULSE
GENERATOR
AD811
V
R
= ؎5V
S
R
L
= 562⍀
FB
0.1F
1M
10M
FREQUENCY – Hz
100M
–V
S
Figure 25. Inverting Amplifier Connection
Figure 28. Closed-Loop Gain vs. Frequency, Gain = –1
26
G = –10
1V
10ns
V
R
= ؎15V
23
20
17
14
11
8
S
R
= 150⍀
L
= 511⍀
FB
100
90
V
IN
V
R
= ؎5V
= 442⍀
S
FB
10
V
OUT
0%
1V
1M
10M
FREQUENCY – Hz
100M
Figure 29. Closed-Loop Gain vs. Frequency, Gain = –10
Figure 26. Small Signal Pulse Response, Gain = –1
1V
20ns
100mV
10ns
100
90
100
90
V
IN
V
IN
10
10
V
OUT
V
OUT
0%
0%
10V
1V
Figure 30. Large Signal Pulse Response, Gain = –10
Figure 27. Small Signal Pulse Response, Gain = –10
–8–
REV. D
AD811
Achieving the Flattest Gain Response at High Frequency
Achieving and maintaining gain flatness of better than 0.1 dB at
frequencies above 10 MHz requires careful consideration of
several issues.
APPLICATIONS
General Design Considerations
The AD811 is a current feedback amplifier optimized for use in
high performance video and data acquisition applications. Since
it uses a current feedback architecture, its closed-loop –3 dB
bandwidth is dependent on the magnitude of the feedback resis-
tor. The desired closed-loop gain and bandwidth are obtained
by varying the feedback resistor (RFB) to tune the bandwidth,
and varying the gain resistor (RG) to get the correct gain. Table I
contains recommended resistor values for a variety of useful
closed-loop gains and supply voltages.
Choice of Feedback and Gain Resistors
Because of the above-mentioned relationship between the 3 dB
bandwidth and the feedback resistor, the fine scale gain flatness
will, to some extent, vary with feedback resistor tolerance. It is,
therefore, recommended that resistors with a 1% tolerance be
used if it is desired to maintain flatness over a wide range of
production lots. In addition, resistors of different construction
have different associated parasitic capacitance and inductance.
Metal-film resistors were used for the bulk of the characteriza-
tion for this data sheet. It is possible that values other than those
indicated will be optimal for other resistor types.
Table I. –3 dB Bandwidth vs. Closed-Loop Gain and
Resistance Values
VS = ؎15 V
Closed-Loop
Gain
Printed Circuit Board Layout Considerations
–3 dB BW
(MHz)
As to be expected for a wideband amplifier, PC board parasitics
can affect the overall closed loop performance. Of concern are
stray capacitances at the output and the inverting input nodes. If
a ground plane is to be used on the same side of the board as
the signal traces, a space (3/16" is plenty) should be left around
the signal lines to minimize coupling. Additionally, signal lines
connecting the feedback and gain resistors should be short
enough so that their associated inductance does not cause
high frequency gain errors. Line lengths less than 1/4" are
recommended.
RFB
RG
+1
+2
+10
–1
–10
750 Ω
649 Ω
511 Ω
590 Ω
511 Ω
140
120
100
115
95
649 Ω
56.2 Ω
590 Ω
51.1 Ω
VS = ؎5 V
Closed-Loop
Gain
–3 dB BW
(MHz)
RFB
RG
Quality of Coaxial Cable
+1
+2
+10
–1
619 Ω
562 Ω
442 Ω
562 Ω
442 Ω
80
80
65
75
65
Optimum flatness when driving a coax cable is possible only
when the driven cable is terminated at each end with a resistor
matching its characteristic impedance. If the coax was ideal,
then the resulting flatness would not be affected by the length of
the cable. While outstanding results can be achieved using inex-
pensive cables, it should be noted that some variation in flatness
due to varying cable lengths may be experienced.
562 Ω
48.7 Ω
562 Ω
44.2 Ω
–10
VS = ؎10 V
Closed-Loop
Gain
–3 dB BW
(MHz)
RFB
RG
Power Supply Bypassing
Adequate power supply bypassing can be critical when optimiz-
ing the performance of a high frequency circuit. Inductance in
the power supply leads can form resonant circuits that produce
peaking in the amplifier’s response. In addition, if large current
transients must be delivered to the load, then bypass capacitors
(typically greater than 1 µF) will be required to provide the best
settling time and lowest distortion. Although the recommended
0.1 µF power supply bypass capacitors will be sufficient in many
applications, more elaborate bypassing (such as using two paral-
leled capacitors) may be required in some cases.
+1
+2
+10
–1
–10
649 Ω
590 Ω
499 Ω
590 Ω
499 Ω
105
105
80
105
80
590 Ω
49.9 Ω
590 Ω
49.9 Ω
Figures 11 and 12 illustrate the relationship between the feed-
back resistor and the frequency and time domain response char-
acteristics for a closed-loop gain of +2. (The response at other
gains will be similar.)
The 3 dB bandwidth is somewhat dependent on the power supply
voltage. As the supply voltage is decreased for example, the
magnitude of internal junction capacitances is increased, causing
a reduction in closed-loop bandwidth. To compensate for this,
smaller values of feedback resistor are used at lower supply
voltages.
REV. D
–9–
AD811
Driving Capacitive Loads
100
90
80
70
60
50
40
30
20
10
0
The feedback and gain resistor values in Table I will result in
very flat closed-loop responses in applications where the load
capacitances are below 10 pF. Capacitances greater than this
will result in increased peaking and overshoot, although not
necessarily in a sustained oscillation.
G = +2
= ؎15V
V
S
R
VALUE SPECIFIED
S
IS FOR FLATTEST
FREQUENCY RESPONSE
There are at least two very effective ways to compensate for this
effect. One way is to increase the magnitude of the feedback
resistor, which lowers the 3 dB frequency. The other method is
to include a small resistor in series with the output of the ampli-
fier to isolate it from the load capacitance. The results of these
two techniques are illustrated in Figure 32. Using a 1.5 kΩ
feedback resistor, the output ripple is less than 0.5 dB when driv-
ing 100 pF. The main disadvantage of this method is that it
sacrifices a little bit of gain flatness for increased capacitive load
drive capability. With the second method, using a series resistor,
the loss of flatness does not occur.
10
100
LOAD CAPACITANCE – pF
1000
Figure 33. Recommended Value of Series Resistor vs. the
Amount of Capacitive Load
R
FB
Figure 33 shows recommended resistor values for different load
capacitances. Refer again to Figure 32 for an example of the
results of this method. Note that it may be necessary to adjust
the gain setting resistor, RG, to correct for the attenuation which
results due to the divider formed by the series resistor, RS, and
the load resistance.
+V
S
0.1F
R
R
G
R
(OPTIONAL)
S
V
Applications which require driving a large load capacitance at a
high slew rate are often limited by the output current available
from the driving amplifier. For example, an amplifier limited to
25 mA output current cannot drive a 500 pF load at a slew rate
greater than 50 V/µs. However, because of the AD811’s 100 mA
output current, a slew rate of 200 V/µs is achievable when driv-
ing this same 500 pF capacitor (see Figure 34).
OUT
AD811
V
IN
C
R
L
L
T
0.1F
–V
S
2V
100ns
Figure 31. Recommended Connection for Driving a Large
Capacitive Load
100
90
V
IN
12
R
R
= 1.5k⍀
= 0
FB
9
6
S
10
V
OUT
3
G = +2
= ؎15V
0%
R
R
= 649⍀
= 30⍀
V
FB
S
R
C
= 10k⍀
= 100pF
S
L
L
5V
0
Figure 34. Output Waveform of an AD811 Driving a
500 pF Load. Gain = +2, RFB = 649 Ω, RS = 15 Ω,
RS = 10 kΩ
–3
–6
1M
10M
FREQUENCY – Hz
100M
Figure 32. Performance Comparison of Two Methods for
Driving a Capacitive Load
–10–
REV. D
AD811
Operation as a Video Line Driver
The AD811 has been designed to offer outstanding perfor-
mance at closed-loop gains of one or greater, while driving
multiple reverse-terminated video loads. The lowest differential
gain and phase errors will be obtained when using ±15 volt
power supplies. With ±12 volt supplies, there will be an insig-
nificant increase in these errors and a slight improvement in
gain flatness. Due to power dissipation considerations, ±12 volt
supplies are recommended for optimum video performance.
Excellent performance can be achieved at much lower supplies
as well.
1V
10ns
100
90
V
IN
10
V
OUT
0%
The closed-loop gain vs. frequency at different supply voltages
is shown in Figure 36. Figure 37 is an oscilloscope photograph
of an AD811 line driver’s pulse response with ±15 volt supplies.
The differential gain and phase error vs. supply are plotted in
Figures 38 and 39, respectively.
1V
Figure 37. Small Signal Pulse Response, Gain = +2,
VS = ±15 V
Another important consideration when driving multiple cables
is the high frequency isolation between the outputs of the
cables. Due to its low output impedance, the AD811 achieves
better than 40 dB of output to output isolation at 5 MHz driv-
ing back terminated 75 Ω cables.
0.10
R = 649⍀
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
F
F
= 3.58MHz
C
100 IRE
MODULATED
RAMP
75⍀ CABLE
649⍀
649⍀
V
#1
OUT
75⍀
+V
75⍀
S
a. DRIVING A SINGLE, BACK TERMINATED,
75⍀ COAX CABLE
DRIVING TWO PARALLEL,
0.1F
b.
BACK TERMINATED, COAX CABLES
75⍀ CABLE
b
V
#2
OUT
AD811
75⍀
75⍀ CABLE
75⍀
V
IN
75⍀
a
5
6
7
8
9
10
11
12
13
14
15
SUPPLY VOLTAGE – ؎Volts
0.1F
Figure 38. Differential Gain Error vs. Supply Voltage for
the Video Line Driver of Figure 35
–V
S
Figure 35. A Video Line Driver Operating at a Gain of +2
0.20
12
R
= 649⍀
= 3.58MHz
F
0.18
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0.02
F
C
G = +2
100 IRE
MODULATED
RAMP
V
R
= ؎15V
S
R
R
= 150⍀
= R
9
6
L
= 649⍀
FB
G
FB
a.DRIVING A SINGLE, BACK TERMINATED,
75⍀ COAX CABLE
DRIVING TWO PARALLEL,
b.
3
BACK TERMINATED, COAX CABLES
V
= ؎5V
S
R
= 562⍀
FB
b
0
–3
–6
a
5
6
7
8
9
10
11
12
13
14
15
1
10
FREQUENCY – MHz
100
SUPPLY VOLTAGE – ؎Volts
Figure 39. Differential Phase Error vs. Supply Voltage for
the Video Line Driver of Figure 35
Figure 36. Closed-Loop Gain vs. Frequency, Gain = +2
REV. D
–11–
AD811
An 80 MHz Voltage-Controlled Amplifier Circuit
The gain can be increased to 20 dB (×10) by raising R8 and R9
to 1.27 kΩ, with a corresponding decrease in –3 dB bandwidth
to about 25 MHz. The maximum output voltage under these
conditions will be increased to ±9 V using ±12 V supplies.
The voltage-controlled amplifier (VCA) circuit of Figure 40
shows the AD811 being used with the AD834, a 500 MHz,
4-quadrant multiplier. The AD834 multiplies the signal input
by the dc control voltage, VG. The AD834 outputs are in the
form of differential currents from a pair of open collectors,
ensuring that the full bandwidth of the multiplier (which ex-
ceeds 500 MHz) is available for certain applications. Here,
the AD811 op amp provides a buffered, single-ended ground-
referenced output. Using feedback resistors R8 and R9 of
511 Ω, the overall gain ranges from –70 dB, for VG = 0 dB to
+12 dB, (a numerical gain of four), when VG = +1 V. The over-
all transfer function of the VCA is:
The gain-control input voltage, VG, may be a positive or nega-
tive ground-referenced voltage, or fully differential, depending
on the user’s choice of connections at Pins 7 and 8. A positive
value of VG results in an overall noninverting response. Revers-
ing the sign of VG simply causes the sign of the overall response
to invert. In fact, although this circuit has been classified as a
voltage-controlled amplifier, it is also quite useful as a general-
purpose four-quadrant multiplier, with good load-driving capa-
bilities and fully-symmetrical responses from X- and Y-inputs.
V
OUT = 4 (X1 – X2)(Y1 – Y2)
The AD811 and AD834 can both be operated from power
supply voltages of ±5 V. While it is not necessary to power them
from the same supplies, the common-mode voltage at W1 and
W2 must be biased within the common-mode range of the
AD811’s input stage. To achieve the lowest differential gain and
phase errors, it is recommended that the AD811 be operated
from power supply voltages of ±10 volts or greater. This VCA
circuit is designed to operate from a ±12 volt dual power
supply.
which reduces to VOUT = 4 VG VIN using the labeling conven-
tions shown in Figure 40. The circuit’s –3 dB bandwidth of
80 MHz, is maintained essentially constant—independent of
gain. The response can be maintained flat to within ±0.1 dB
from dc to 40 MHz at full gain with the addition of an optional
capacitor of about 0.3 pF across the feedback resistor R8. The
circuit produces a full-scale output of ±4 V for a ±1 V input,
and can drive a reverse-terminated load of 50 Ω or 75 Ω to ±2 V.
FB
+12V
C1
0.1F
R1 100⍀
R8*
+
V
G
–
R2 100⍀
8
7
6
5
R4
182⍀
R6
294⍀
X2
X1 +V
W1
S
U1
AD834
U3
AD811
V
OUT
–V
3
S
Y1 Y2
W2
4
R7
294⍀
R5
182⍀
R
L
1
2
V
IN
R9*
R3
249⍀
C2
0.1F
–12V
FB
*R8 = R9 = 511⍀ FOR X4 GAIN
= 1.27k⍀ FOR X10 GAIN
Figure 40. An 80 MHz Voltage-Controlled Amplifier
–12–
REV. D
AD811
A Video Keyer Circuit
The bias currents required at the output of the multipliers are
provided by R8 and R9. A dc-level-shifting network comprising
R10/R12 and R11/R13 ensures that the input nodes of the
AD811 are positioned at a voltage within its common-mode
range. At high frequencies C1 and C2 bypass R10 and R11
respectively. R14 is included to lower the HF loop gain, and is
needed because the voltage-to-current conversion in the
AD834s, via the Y2 inputs, results in an effective value of the
feedback resistance of 250 Ω; this is only about half the value
required for optimum flatness in the AD811’s response. (Note
that this resistance is unaffected by G: when G = 1, all the
feedback is via U1, while when G = 0 it is all via U2). R14
reduces the fractional amount of output current from the multi-
pliers into the current-summing inverting input of the AD811,
by sharing it with R8. This resistor can be used to adjust the
bandwidth and damping factor to best suit the application.
By using two AD834 multipliers, an AD811, and a 1 V dc
source, a special form of a two-input VCA circuit called a
video keyer can be assembled. “Keying” is the term used in
reference to blending two or more video sources under the
control of a third signal or signals to create such special effects
as dissolves and overlays. The circuit shown in Figure 41 is a
two-input keyer, with video inputs VA and VB, and a control
input VG. The transfer function (with VOUT at the load) is
given by:
VOUT = G VA + (1–G) VB
where G is a dimensionless variable (actually, just the gain of
the “A” signal path) that ranges from 0 when VG = 0, to 1
when VG = +1 V. Thus, VOUT varies continuously between VA
and VB as G varies from 0 to 1.
Circuit operation is straightforward. Consider first the signal
path through U1, which handles video input VA. Its gain is
clearly zero when VG = 0 and the scaling we have chosen
ensures that it is unity when VG = +1 V; this takes care of the
first term of the transfer function. On the other hand, the VG
input to U2 is taken to the inverting input X2 while X1 is
biased at an accurate +1 V. Thus, when VG = 0, the response
to video input VB is already at its full-scale value of unity,
whereas when VG = +1 V, the differential input X1–X2 is zero.
This generates the second term.
To generate the 1 V dc needed for the “1–G” term an AD589
reference supplies 1.225 V ± 25 mV to a voltage divider consist-
ing of resistors R2 through R4. Potentiometer R3 should be
adjusted to provide exactly +1 V at the X1 input.
In this case, we have shown an arrangement using dual supplies
of ±5 V for both the AD834 and the AD811. Also, the overall
gain in this case is arranged to be unity at the load, when it is
driven from a reverse-terminated 75 Ω line. This means that the
“dual VCA” has to operate at a maximum gain of 2, rather
C1
+5V
R7
R14
0.1F
SETUP FOR DRIVING
REVERSE-TERMINATED LOAD
SEE TEXT
45.3⍀
R10
2.49k⍀
Z
V
OUT
O
R5
TO PIN 6
AD811
113⍀
V
R6
226⍀
G
Z
200⍀
200⍀
O
(0 TO +1V dc)
TO Y2
8
7
6
5
X2
X1 +V
W1
S
+5V
R1
INSET
R8
29.4⍀
U1
AD834
R12
6.98k⍀
U4
1.87k⍀
AD589
+5V
Y1 Y2 –V
W2
4
S
R2
174⍀
2
1
3
V
A
FB
C3
0.1F
(؎1V FS)
–5V
–5V
+5V
R3
100⍀
LOAD
GND
U3
AD811
R9
29.4⍀
R13
6.98k⍀
8
7
6
5
V
OUT
R4
1.02k⍀
X2
W1
X1 +V
S
C4
0.1F
C2
0.1F
U1
AD834
Y1 Y2 –V
W2
4
S
LOAD
GND
FB
2
1
3
R11
2.49k⍀
V
B
–5V
–5V
(؎1V FS)
Figure 41. A Practical Video Keyer Circuit
REV. D
–13–
AD811
than 4 as in the VCA circuit of Figure 40. However, this cannot
be achieved by lowering the feedback resistor, since below a
critical value (not much less than 500 Ω) the AD811’s peaking
may be unacceptable. This is because the dominant pole in the
open-loop ac response of a current-feedback amplifier is con-
trolled by this feedback resistor. It would be possible to operate
at a gain of X4 and then attenuate the signal at the output.
Instead, we have chosen to attenuate the signals by 6 dB at the
input to the AD811; this is the function of R8 through R11.
R14 = 49.9⍀
0
–10
–20
–30
–40
–50
–60
–70
–80
GAIN
R14 = 137⍀
ADJACENT
CHANNEL
FEEDTHROUGH
Figure 42 is a plot of the ac response of the feedback keyer,
when driving a reverse terminated 50 Ω cable. Output noise and
adjacent channel feedthrough, with either channel fully off and
the other fully on, is about –50 dB to 10 MHz. The feedthrough
at 100 MHz is limited primarily by board layout. For VG = +1 V,
the –3 dB bandwidth is 15 MHz when using a 137 Ω resistor for
R14 and 70 MHz with R14 = 49.9 Ω. For further information
regarding the design and operation of the VCA and video keyer
circuits, refer to the application note “Video VCA’s and Keyers
Using the AD834 & AD811” by Brunner, Clarke, and Gilbert,
available FREE from Analog Devices.
10k
100k
1M
FREQUENCY – Hz
10M
100M
Figure 42. A Plot of the AC Response of the Video Keyer
–14–
REV. D
AD811
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8- Lead Plastic DIP (N) Package
20-Lead LCC (E-20A) Package
0.082 ± 0.018
(2.085 ± 0.455)
0.39 (9.91)
MAX
0.350 ± 0.008 SQ
(8.89 ± 0.20) SQ
0.040 x 45°
(1.02 x 45°)
REF 3 PLCS
8
5
0.31
(7.87)
0.25
(6.35)
1
4
0.025 ± 0.003
(0.635 ± 0.075)
PIN 1
0.30 (7.62)
REF
NO. 1 PIN
INDEX
0.10 (2.54)
BSC
0.035 ؎ 0.01
(0.89 ؎ 0.25)
0.050
(1.27)
0.165 ؎ 0.01
(4.19 ؎ 0.25)
0.011 ؎0.003
(0.28 ؎ 0.08)
0.020 x 45°
(0.51 x 45°)
REF
0.18 ؎0.03
(4.57 ؎ 0.75)
0.125 (3.18)
MIN
15؇
0؇
0.018 ؎0.003
(0.46 ؎ 0.08)
SEATING
PLANE
0.033
(0.84)
NOM
16-Lead SOIC (R-16) Package
8-Lead Cerdip (Q) Package
9
16
0.005 (0.13) 0.055 (1.4)
0.299 (7.60)
0.291 (7.40)
MIN
MAX
8
5
0.419 (10.65)
PIN 1
0.404 (10.26)
8
0.310 (7.87)
0.220 (5.59)
1
PIN 1
1
4
0.100 (2.54) BSC
0.405 (10.29) MAX
0.107 (2.72)
0.413 (10.50)
0.398 (10.10)
0.320 (8.13)
0.290 (7.37)
0.089 (2.26)
0.364 (9.246)
0.344 (8.738)
0.060 (1.52)
0.015 (0.38)
0.200.(5.08)
MAX
0.150
(3.81)
MIN
0.045 (1.15)
0.020 (0.50)
0.200 (5.08)
0.125 (3.18)
0.010 (0.25)
0.004 (0.10)
0.050 (1.27)
BSC
0.018 (0.46)
0.014 (0.36)
0.015 (0.38)
0.007 (1.18)
0.015 (0.38)
0.008 (0.20)
SEATING
PLANE
15°
0°
0.023 (0.58) 0.070 (1.78)
0.014 (0.36) 0.030 (0.76)
20-Lead Wide Body SOIC (R-20) Package
8-Lead SOIC (SO-8) Package
0.512 (13.00)
0.496 (12.60)
0.1968 (5.00)
0.1890 (4.80)
20
11
8
1
5
4
0.2440 (6.20)
0.2284 (5.80)
0.1574 (4.00)
0.1497 (3.80)
0.300 (7.60)
0.292 (7.40)
0.419 (10.65)
PIN 1
0.394 (10.00)
0.0196 (0.50)
0.0099 (0.25)
0.0500 (1.27)
BSC
10
1
؋
45؇ 0.0688 (1.75)
0.0532 (1.35)
0.0098 (0.25)
0.0040 (0.10)
SEATING
PLANE
0.50 (1.27)
BSC
0.019 (0.48)
0.014 (0.36)
8؇
0؇
0.0500 (1.27)
0.0160 (0.41)
0.0192 (0.49)
0.0138 (0.35)
0.0098 (0.25)
0.0075 (0.19)
0.104 (2.64)
0.093 (2.36)
0.011 (0.28)
0.004 (0.10)
0.015 (0.38)
0.007 (0.18)
0.050 (1.27)
0.016 (0.40)
REV. D
–15–
相关型号:
©2020 ICPDF网 联系我们和版权申明