AD8065ARTZ-REEL [ADI]
High Performance, 145 MHz FastFET⑩ Op Amps; 高性能, 145 MHz的FastFET⑩运算放大器型号: | AD8065ARTZ-REEL |
厂家: | ADI |
描述: | High Performance, 145 MHz FastFET⑩ Op Amps |
文件: | 总28页 (文件大小:560K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
High Performance, 145 MHz
FastFET™ Op Amps
AD8065/AD8066
FEATURES
APPLICATIONS
FET input amplifier
1 pA input bias current
Low cost
Instrumentation
Photodiode preamps
Filters
High speed: 145 MHz, −3 dB bandwidth (G = +1)
180 V/μs slew rate (G = +2)
A/D drivers
Level shifting
Low noise
Buffering
7 nV/√Hz (f = 10 kHz)
0.6 fA/√Hz (f = 10 kHz)
CONNECTION DIAGRAMS
AD8065
AD8065
V
+V
1
2
3
5
OUT
NC
–IN
+IN
1
2
3
4
8
7
6
5
NC
+V
S
Wide supply voltage range: 5 V to 24 V
Single-supply and rail-to-rail output
Low offset voltage 1.5 mV maximum
High common-mode rejection ratio: −100 dB
Excellent distortion specifications
SFDR −88 dBc @ 1 MHz
Low power: 6.4 mA/amplifier typical supply current
No phase reversal
Small packaging: SOIC-8, SOT-23-5, and MSOP-8
–V
S
S
V
4
+IN
–IN
OUT
TOP VIEW
(Not to Scale)
–V
S
NC
TOP VIEW
(Not to Scale)
AD8066
1
2
3
4
8
7
6
5
+V
S
V
OUT1
V
–IN1
+IN1
OUT2
–IN2
+IN2
–V
S
TOP VIEW
(Not to Scale)
Figure 1.
GENERAL DESCRIPTION
operate using only a 6.4 mA/amplifier typical supply current
and are capable of delivering up to 30 mA of load current.
The AD8065/AD80661 FastFET amplifiers are voltage feedback
amplifiers with FET inputs offering high performance and ease
of use. The AD8065 is a single amplifier, and the AD8066 is a
dual amplifier. These amplifiers are developed in the Analog
Devices, Inc. proprietary XFCB process and allow exceptionally
low noise operation (7.0 nV/√Hz and 0.6 fA/√Hz) as well as
very high input impedance.
The AD8065/AD8066 are high performance, high speed, FET
input amplifiers available in small packages: SOIC-8, MSOP-8,
and SOT-23-5. They are rated to work over the industrial
temperature range of −40°C to +85°C.
24
With a wide supply voltage range from 5 V to 24 V, the ability to
operate on single supplies, and a bandwidth of 145 MHz, the
AD8065/AD8066 are designed to work in a variety of
applications. For added versatility, the amplifiers also contain
rail-to-rail outputs.
21
18
15
12
9
G = +10
G = +5
V
= 200mV p-p
O
G = +2
G = +1
6
Despite the low cost, the amplifiers provide excellent overall
performance. The differential gain and phase errors of 0.02%
and 0.02°, respectively, along with 0.1 dB flatness out to 7 MHz,
make these amplifiers ideal for video applications. Additionally,
they offer a high slew rate of 180 V/μs, excellent distortion
(SFDR of −88 dBc @ 1 MHz), extremely high common-mode
rejection of −100 dB, and a low input offset voltage of 1.5 mV
maximum under warmed up conditions. The AD8065/ AD8066
1 Protected by U. S. Patent No. 6,262,633.
3
0
–3
–6
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 2. Small Signal Frequency Response
Rev. G
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
© 2006 Analog Devices, Inc. All rights reserved.
AD8065/AD8066
TABLE OF CONTENTS
Features .............................................................................................. 1
Input Protection ......................................................................... 19
Thermal Considerations............................................................ 20
Input and Output Overload Behavior ..................................... 20
Layout, Grounding, and Bypassing Considerations .................. 21
Power Supply Bypassing............................................................ 21
Grounding................................................................................... 21
Leakage Currents........................................................................ 22
Input Capacitance ...................................................................... 22
Output Capacitance ................................................................... 22
Input-to-Output Coupling........................................................ 23
Wideband Photodiode Preamp................................................ 23
High Speed JFET Input Instrumentation Amplifier.............. 24
Video Buffer ................................................................................ 24
Outline Dimensions....................................................................... 25
Ordering Guide .......................................................................... 26
Applications....................................................................................... 1
General Description......................................................................... 1
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 6
ESD Caution.................................................................................. 6
Maximum Power Dissipation ..................................................... 7
Output Short Circuit.................................................................... 7
Typical Performance Characteristics ............................................. 8
Test Circuits................................................................................. 15
Theory of Operation ...................................................................... 18
Closed-Loop Frequency Response........................................... 18
Noninverting Closed-Loop Frequency Response.................. 18
Inverting Closed-Loop Frequency Response ......................... 18
Wideband Operation ................................................................. 19
2/03—Data Sheet changed from Rev. A to Rev. B.
REVISION HISTORY
Changes to Absolute Maximum Ratings...................................... 4
Changes to Test Circuit 10 ........................................................... 14
Changes to Test Circuit 11 ........................................................... 15
Changes to Noninverting Closed-Loop Frequency Response 16
Changes to Inverting Closed-Loop Frequency Response ....... 16
Updated Figure 6 .......................................................................... 18
Changes to Figure 7....................................................................... 19
Changes to Figure 10..................................................................... 21
Changes to Figure 11..................................................................... 22
Changes to High Speed JFET Instrumentation Amplifier....... 22
Changes to Video Buffer............................................................... 22
1/06—Rev. F to Rev. G
Changes to Ordering Guide .......................................................... 26
12/05—Rev. E to Rev. F
Updated Format..................................................................Universal
Changes to Features.......................................................................... 1
Changes to General Description .................................................... 1
Changes to Figure 22 through Figure 27..................................... 11
Updated Outline Dimensions....................................................... 25
Changes to Ordering Guide .......................................................... 26
2/04—Data Sheet Changed from Rev. D to Rev. E.
Updated Format................................................................ Universal
Updated Figure 56 .........................................................................21
Updated Outline Dimensions......................................................25
Updated Ordering Guide..............................................................26
8/02—Data Sheet changed from Rev. 0 to Rev. A.
Added AD8066 ..................................................................Universal
Added SOIC-8 (R) and MSOP-8 (RM) ........................................ 1
Edits to General Description ......................................................... 1
Edits to Specifications..................................................................... 2
New Figure 2 .................................................................................... 5
Changes to Ordering Guide........................................................... 5
Edits to TPCs 18, 25, and 28 .......................................................... 8
New TPC 36 ................................................................................... 11
Added Test Circuits 10 and 11..................................................... 14
MSOP (RM-8) added.................................................................... 23
11/03—Data Sheet changed from Rev. C to Rev. D.
Changes to Features......................................................................... 1
Changes to Connection Diagrams ................................................ 1
Updated Ordering Guide................................................................ 5
Updated Outline Dimensions......................................................22
4/03—Data Sheet changed from Rev. B to Rev. C.
Added SOIC-8 (R) for the AD8065............................................... 4
Rev. G | Page 2 of 28
AD8065/AD8066
SPECIFICATIONS
@ TA = 25°C, VS = 5 V, RL = 1 kΩ, unless otherwise noted.
Table 1.
Parameter
Conditions
Min
Typ
Max Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
G = +1, VO = 0.2 V p-p (AD8065)
G = +1, VO = 0.2 V p-p (AD8066)
G = +2, VO = 0.2 V p-p
G = +2, VO = 2 V p-p
G = +2, VO = 0.2 V p-p
G = +1, −5.5 V to +5.5 V
G = −1, −5.5 V to +5.5 V
G = +2, VO = 4 V step
100
100
145
120
50
42
7
175
170
180
55
MHz
MHz
MHz
MHz
MHz
ns
ns
V/μs
ns
Bandwidth for 0.1 dB Flatness
Input Overdrive Recovery Time
Output Recovery Time
Slew Rate
130
Settling Time to 0.1%
G = +2, VO = 2 V step
G = +2, VO = 8 V step
205
ns
NOISE/HARMONIC PERFORMANCE
SFDR
fC = 1 MHz, G = +2, VO = 2 V p-p
fC = 5 MHz, G = +2, VO = 2 V p-p
fC = 1 MHz, G = +2, VO = 8 V p-p
fC = 10 MHz, RL = 100 Ω
f = 10 kHz
f = 10 kHz
NTSC, G = +2, RL = 150 Ω
NTSC, G = +2, RL = 150 Ω
−88
−67
−73
24
7
0.6
dBc
dBc
dBc
dBm
nV/√Hz
fA/√Hz
%
Third-Order Intercept
Input Voltage Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
DC PERFORMANCE
0.02
0.02
Degrees
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
VCM = 0 V, SOIC package
0.4
1
2
25
1
1.5
17
6
mV
μV/°C
pA
pA
pA
SOIC package
TMIN to TMAX
Input Offset Current
10
TMIN to TMAX
1
pA
Open-Loop Gain
VO = 3 V, RL = 1 kΩ
100
113
dB
INPUT CHARACTERISTICS
Common-Mode Input Impedance
Differential Input Impedance
Input Common-Mode Voltage Range
FET Input Range
1000 || 2.1
1000 || 4.5
GΩ || pF
GΩ || pF
−5 to +1.7
−5.0 to +2.4
−5.0 to +5.0
−100
V
V
dB
dB
Usable Range
Common-Mode Rejection Ratio
See the Theory of Operation section
VCM = −1 V to +1 V
VCM = −1 V to +1 V (SOT-23)
−85
−82
−91
OUTPUT CHARACTERISTICS
Output Voltage Swing
RL = 1 kΩ
−4.88 to +4.90 −4.94 to +4.95
V
RL = 150 Ω
−4.8 to +4.7
V
Output Current
VO = 9 V p-p, SFDR ≥ −60 dBc, f = 500 kHz
35
90
20
mA
mA
pF
Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
30% overshoot G = +1
Operating Range
5
24
V
Quiescent Current per Amplifier
Power Supply Rejection Ratio
6.4
−100
7.2
mA
dB
PSRR
−85
Rev. G | Page 3 of 28
AD8065/AD8066
@ TA = 25°C, VS = 12 V, RL = 1 kΩ, unless otherwise noted.
Table 2.
Parameter
Conditions
Min
Typ
Max Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
G = +1, VO = 0.2 V p-p (AD8065)
G = +1, VO = 0.2 V p-p (AD8066)
G = +2, VO = 0.2 V p-p
G = +2, VO = 2 V p-p
G = +2, VO = 0.2 V p-p
G = +1, −12.5 V to +12.5 V
G = −1, −12.5 V to +12.5 V
G = +2, VO = 4 V step
100
100
145
115
50
40
7
175
170
180
55
MHz
MHz
MHz
MHz
MHz
ns
ns
V/μs
ns
Bandwidth for 0.1 dB Flatness
Input Overdrive Recovery
Output Overdrive Recovery
Slew Rate
130
Settling Time to 0.1%
G = +2, VO = 2 V step
G = +2, VO = 10 V step
250
ns
NOISE/HARMONIC PERFORMANCE
SFDR
fC = 1 MHz, G = +2, VO = 2 V p-p
fC = 5 MHz, G = +2, VO = 2 V p-p
fC = 1 MHz, G = +2, VO = 10 V p-p
fC = 10 MHz, RL = 100 Ω
f = 10 kHz
f = 10 kHz
NTSC, G = +2, RL = 150 Ω
NTSC, G = +2, RL = 150 Ω
−100
−67
−85
24
7
1
dBc
dBc
dBc
dBm
nV/√Hz
fA/√Hz
%
Third-Order Intercept
Input Voltage Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
DC PERFORMANCE
0.04
0.03
Degrees
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
VCM = 0 V, SOIC package
0.4
1
3
25
2
1.5
17
7
mV
μV/°C
pA
pA
pA
SOIC package
TMIN to TMAX
Input Offset Current
10
TMIN to TMAX
2
pA
Open-Loop Gain
VO = 10 V, RL = 1 kΩ
103
114
dB
INPUT CHARACTERISTICS
Common-Mode Input Impedance
Differential Input Impedance
Input Common-Mode Voltage Range
FET Input Range
1000 || 2.1
1000 || 4.5
GΩ || pF
GΩ || pF
−12 to +8.5
−12.0 to +9.5
−12.0 to +12.0
−100
V
V
dB
dB
Usable Range
Common-Mode Rejection Ratio
See the Theory of Operation section
VCM = −1 V to +1 V
VCM = −1 V to +1 V (SOT-23)
−85
−82
−91
OUTPUT CHARACTERISTICS
Output Voltage Swing
RL = 1 kΩ
−11.8 to +11.8 −11.9 to +11.9
V
RL = 350 Ω
−11.25 to +11.5
V
Output Current
VO = 22 V p-p, SFDR ≥ −60 dBc, f = 500 kHz
30
120
25
mA
mA
pF
Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
30% overshoot G = +1
Operating Range
5
24
V
Quiescent Current per Amplifier
Power Supply Rejection Ratio
6.6
−93
7.4
mA
dB
PSRR
−84
Rev. G | Page 4 of 28
AD8065/AD8066
@ TA = 25°C, VS = 5 V, RL = 1 kΩ, unless otherwise noted.
Table 3.
Parameter
Conditions
Min
Typ
Max Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
G = +1, VO = 0.2 V p-p (AD8065)
G = +1, VO = 0.2 V p-p (AD8066)
G = +2, VO = 0.2 V p-p
G = +2, VO = 2 V p-p
G = +2, VO = 0.2 V p-p
G = +1, −0.5 V to +5.5 V
G = −1, −0.5 V to +5.5 V
G = +2, VO = 2 V step
125
110
155
130
50
43
6
175
170
160
60
MHz
MHz
MHz
MHz
MHz
ns
ns
V/μs
ns
Bandwidth for 0.1 dB Flatness
Input Overdrive Recovery Time
Output Recovery Time
Slew Rate
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
SFDR
105
G = +2, VO = 2 V step
fC = 1 MHz, G = +2, VO = 2 V p-p
fC = 5 MHz, G = +2, VO = 2 V p-p
fC = 10 MHz, RL = 100 Ω
f = 10 kHz
f = 10 kHz
NTSC, G = +2, RL = 150 Ω
NTSC, G = +2, RL = 150 Ω
−65
−50
22
7
0.6
dBc
dBc
dBm
nV/√Hz
fA/√Hz
%
Third-Order Intercept
Input Voltage Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
DC PERFORMANCE
0.13
0.16
Degrees
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
VCM = 1.0 V, SOIC package
0.4
1
1
25
1
1
1.5
17
5
mV
μV/ºC
pA
pA
pA
pA
dB
dB
SOIC package
TMIN to TMAX
Input Offset Current
Open-Loop Gain
5
TMIN to TMAX
VO = 1 V to 4 V (AD8065)
VO = 1 V to 4 V (AD8066)
100
90
113
103
INPUT CHARACTERISTICS
Common-Mode Input Impedance
Differential Input Impedance
Input Common-Mode Voltage Range
FET Input Range
1000 || 2.1
1000 || 4.5
GΩ || pF
GΩ || pF
0 to 1.7
0 to 2.4
0 to 5.0
−100
V
V
dB
dB
Usable Range
Common-Mode Rejection Ratio
See the Theory of Operation section
VCM = 0.5 V to 1.5 V
VCM = 1 V to 2 V (SOT-23)
−74
−78
−91
OUTPUT CHARACTERISTICS
Output Voltage Swing
RL = 1 kΩ
0.1 to 4.85
0.03 to 4.95
V
RL = 150 Ω
0.07 to 4.83
V
Output Current
VO = 4 V p-p, SFDR ≥ −60 dBc, f = 500 kHz
35
75
5
mA
mA
pF
Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
30% overshoot G = +1
Operating Range
5
24
V
Quiescent Current per Amplifier
Power Supply Rejection Ratio
5.8
−78
6.4
−100
7.0
mA
dB
PSRR
Rev. G | Page 5 of 28
AD8065/AD8066
ABSOLUTE MAXIMUM RATINGS
Table 4.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Parameter
Rating
Supply Voltage
26.4 V
Power Dissipation
See Figure 3
VEE − 0.5 V to VCC + 0.5 V
1.8 V
−65°C to +125°C
−40°C to +85°C
300°C
Common-Mode Input Voltage
Differential Input Voltage
Storage Temperature Range
Operating Temperature Range
Lead Temperature
(Soldering, 10 sec)
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. G | Page 6 of 28
AD8065/AD8066
MAXIMUM POWER DISSIPATION
2.0
1.5
1.0
0.5
0
The maximum safe power dissipation in the AD8065/AD8066
packages is limited by the associated rise in junction
temperature (TJ) on the die. The plastic encapsulating the die
locally reaches the junction temperature. At approximately
150°C, which is the glass transition temperature, the plastic
changes its properties. Even temporarily exceeding this
temperature limit can change the stresses that the package
exerts on the die, permanently shifting the parametric
performance of the AD8065/AD8066. Exceeding a junction
temperature of 175°C for an extended time can result in
changes in the silicon devices, potentially causing failure.
MSOP-8
SOIC-8
SOT-23-5
The still air thermal properties of the package and PCB (θJA),
ambient temperature (TA), and total power dissipated in the
package (PD) determine the junction temperature of the die.
The junction temperature can be calculated by
–60
–40
–20
0
20
40
60
80
100
AMBIENT TEMPERATURE (°C)
Figure 3. Maximum Power Dissipation vs. Temperature for a 4-Layer Board
Airflow increases heat dissipation, effectively reducing θJA. Also,
more metal directly in contact with the package leads from
metal traces, through holes, ground, and power planes reduce
the θJA. Care must be taken to minimize parasitic capacitances
at the input leads of high speed op amps as discussed in the
Layout, Grounding, and Bypassing Considerations section.
TJ = TA + (PD × θJA)
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive for all outputs. The quiescent
power is the voltage between the supply pins (VS) times the
quiescent current (IS). Assuming the load (RL) is referenced to
midsupply, then the total drive power is VS /2 × IOUT, some
of which is dissipated in the package and some in the load
(VOUT × IOUT). The difference between the total drive power and
the load power is the drive power dissipated in the package.
Figure 3 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the SOIC (125°C/W),
SOT-23 (180°C/W), and MSOP (150°C/W) packages on a
JEDEC standard 4-layer board. θJA values are approximations.
PD = Quiescent Power +
Total Drive Power − Load Power
OUTPUT SHORT CIRCUIT
2
Shorting the output to ground or drawing excessive current for
the AD8065/AD8066 will likely cause catastrophic failure.
V
VOUT
RL
VOUT
RL
⎛
⎜
⎞
⎟
S
PD =
(
VS × IS
)
+
×
−
2
⎝
⎠
RMS output voltages should be considered. If RL is referenced to
VS−, as in single-supply operation, then the total drive power is
VS × IOUT
.
If the rms signal levels are indeterminate, then consider the
worst case, when VOUT = VS/4 for RL to midsupply.
2
(
VS/4
RL
)
PD =
(
VS × IS +
)
In single-supply operation with RL referenced to VS−, worst case
is VOUT = VS/2.
Rev. G | Page 7 of 28
AD8065/AD8066
TYPICAL PERFORMANCE CHARACTERISTICS
Default Conditions: 5 V, CL = 5 pF, RL = 1 kΩ, VOUT = 2 V p-p, Temperature = 25°C.
24
21
18
15
12
9
6.9
6.8
6.7
6.6
6.5
6.4
6.3
6.2
6.1
6.0
5.9
R
= 150Ω
L
G = +10
G = +5
G = +2
V
V
= 0.2V p-p
= 0.7V p-p
V
= 200mV p-p
OUT
O
OUT
V
= 1.4V p-p
OUT
G = +2
G = +1
6
3
0
–3
–6
0.1
1
10
100
1000
0.1
1
10
FREQUENCY (MHz)
100
FREQUENCY (MHz)
Figure 4. Small Signal Frequency Response for Various Gains
Figure 7. 0.1 dB Flatness Frequency Response (See Figure 43)
6
4
9
8
7
6
5
4
3
V
= 200mV p-p
V = 200mV p-p
O
O
G = +1
G = +2
V
= +5V
S
V
= +5V
S
2
V
= ±5V
S
V
= ±5V
S
0
V
= ±12V
S
V
= ±12V
S
–2
–4
–6
0.1
1
10
FREQUENCY (MHz)
100
1000
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 5. Small Signal Frequency Response for Various Supplies
(See Figure 42)
Figure 8. Small Signal Frequency Response for Various Supplies
(See Figure 43)
2
8
V
= 2V p-p
O
G = +1
G = +2
7
6
5
4
3
2
1
0
V
= +5V
1
0
S
V
= ±5V
S
V
= ±12V
S
V
= ±5V
S
–1
–2
–3
–4
–5
V
= ±12V
S
0.1
1
10
FREQUENCY (MHz)
100
1000
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 6. Large Signal Frequency Response for Various Supplies
(See Figure 42)
Figure 9. Large Signal Frequency Response for Various Supplies
(See Figure 43)
Rev. G | Page 8 of 28
AD8065/AD8066
9
6
8
6
V
= 200mV p-p
O
C
R
= 25pF
L
G = +1
= 20
Ω
SNUB
C
C
= 25pF
= 20pF
C
= 55pF
= 25pF
L
L
L
C
= 5pF
L
4
C
L
3
2
0
0
C
= 5pF
L
–2
–4
–6
–8
–3
–6
–9
V
= 200mV p-p
O
G = +2
0.1
1
10
FREQUENCY (MHz)
100
1000
0.1
1
10
FREQUENCY (MHz)
100
1000
Figure 10. Small Signal Frequency Response for Various CLOAD (See Figure 42)
Figure 13. Small Signal Frequency Response for Various CLOAD (See Figure 43)
8
8
V
= 0.2V p-p
OUT
R
= 100Ω
6
4
7
6
5
4
3
2
1
0
L
V
= 2V p-p
= 4V p-p
G = +2
OUT
R
= 1kΩ
L
2
V
OUT
0
–2
–4
–6
–8
V
= 200mV p-p
O
G = +2
0.1
1
10
100
1000
0.1
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 11. Frequency Response for Various Output Amplitudes
(See Figure 43)
Figure 14. Small Signal Frequency Response for Various RLOAD (See Figure 43)
80
60
40
20
0
120
60
14
12
10
8
V
= 200mV p-p
O
G = +2
PHASE
R
R
= R = 1kΩ,
F
S
G
= 500Ω
R
R
= R = 500Ω,
F
S
G
0
= 250Ω
6
GAIN
R
R
C
= R = 500Ω,
F
S
F
G
4
= 250Ω,
= 2.2pF
–60
–120
–180
R
= R = 1kΩ,
G
F
R
= 500Ω,
S
2
C
= 3.3pF
F
0
–2
–4
–20
0.01
0.1
1
10
100
1000
0.1
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 12. Small Signal Frequency Response for Various RF/CF (See Figure 43)
Figure 15. Open-Loop Response
Rev. G | Page 9 of 28
AD8065/AD8066
–40
–50
–30
–40
–50
G = +2
–60
HD2 G = +2
–60
HD3 G = +2
–70
–70
HD2 R = 150
Ω
L
HD2 R = 1k
Ω
HD2 G = +1
L
–80
–80
HD3 R = 1k
Ω
L
–90
–90
HD3 R = 150
Ω
L
HD3 G = +1
–100
–110
–120
–100
–110
0.1
1
10
FREQUENCY (MHz)
100
0.1
1
10
FREQUENCY (MHz)
100
Figure 19. Harmonic Distortion vs. Frequency for Various Gains
(See Figure 42 and Figure 43)
Figure 16. Harmonic Distortion vs. Frequency for Various Loads
(See Figure 43)
–20
–30
–30
V
= ±12V
S
–40
–50
G = +2
= ±12V
F = 1MHz
G = +2
HD2 V = 20V p-p
O
V
S
–40
HD3 V = 20V p-p
–50
O
–60
–60
HD2 V = 10V p-p
O
HD2 R = 150
Ω
–70
L
–70
HD3 R = 150
Ω
L
–80
HD3 V = 10V p-p
–80
O
–90
HD2 R = 300
Ω
–90
L
–100
–110
–120
HD2 V = 2V p-p
–100
–110
–120
O
HD3 R = 300
Ω
L
HD3 V = 2V p-p
O
0.1
1.0
10.0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
OUTPUT AMPLITUDE (V p-p)
FREQUENCY (MHz)
Figure 17. Harmonic Distortion vs. Amplitude for Various Loads VS = 12 V
(See Figure 43)
Figure 20. Harmonic Distortion vs. Frequency for Various Amplitudes
(See Figure 43)
50
100
10
1
R
= 100Ω
L
V
= ±12V
S
45
40
35
30
25
20
15
V
= ±5V
S
V
= +5V
S
10
100
1k
10k
100k
1M
10M
100M
1G
1
10
FREQUENCY (Hz)
FREQUENCY (MHz)
Figure 21. Voltage Noise
Figure 18. Third-Order Intercept vs. Frequency and Supply Voltage
Rev. G | Page 10 of 28
AD8065/AD8066
G = +1
C
= 20pF
L
G = +1
C
= 5pF
L
25ns/DIV
50mV/DIV
25ns/DIV
50mV/DIV
Figure 22. Small Signal Transient Response 5 V Supply (See Figure 42)
Figure 25. Small Signal Transient Response 5 V (See Figure 42)
G = +2
5µs
S
G = +1
V
= 10V p-p
= 4V p-p
V
= ±12V
OUT
V
= ±12V
S
V
= 10V p-p
= 2V p-p
OUT
V
OUT
V
OUT
V
= 2V p-p
OUT
50ns/DIV
2V/DIV
50ns/DIV
2V/DIV
Figure 23. Large Signal Transient Response (See Figure 42)
Figure 26. Large Signal Transient Response (See Figure 43)
G = +1
G = –1
V
= ±5V
V
= ±5V
S
S
2.0V/DIV
100ns/DIV
2.0V/DIV
100ns/DIV
Figure 24. Output Overdrive Recovery (See Figure 44)
Figure 27. Input Overdrive Recovery (See Figure 42)
Rev. G | Page 11 of 28
AD8065/AD8066
V
= 140mV/DIV
IN
V
= 500mV/DIV
IN
V
– 2V
IN
OUT
+0.1%
+0.1%
–0.1%
–0.1%
t = 0
t = 0
V
– 2V
IN
OUT
2mV/DIV
10ns/DIV
2mV/DIV
64μs/DIV
Figure 28. Long-Term Settling Time (See Figure 49)
Figure 31. 0.1% Short-Term Settling Time (See Figure 49)
0
–5
42
36
30
24
18
12
6
+I
b
–I
b
–I
b
–10
–15
–20
–25
–30
0
10
5
–I
b
+I
0
b
–5
–10
–15
+I
b
–20
–25
–30
25
35
45
55
65
75
85
–12 –10 –8 –6 –4 –2
0
2
4
6
8
10 12
COMMON-MODEVOLTAGE (V)
TEMPERATURE (°C)
Figure 32. Input Bias Current vs. Common-Mode Voltage Range
(See the Input and Output Overload Behavior Section)
Figure 29. Input Bias Current vs. Temperature
0.3
0.2
40
N = 299
SD = 0.388
MEAN = –0.069
35
30
0.1
25
20
15
10
5
V
= +5V
S
V
= ±5V
S
0
–0.1
–0.2
–0.3
V
= ±12V
S
0
–2.0
–14 –12 –10 –8 –6 –4 –2
0
2
4
6
8
10 12 14
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
2.0
COMMON-MODE VOLTAGE (V)
INPUT OFFSET VOLTAGE (mV)
Figure 30. Input Offset Voltage vs. Common-Mode Voltage
Figure 33. Input Offset Voltage
Rev. G | Page 12 of 28
AD8065/AD8066
–30
–40
–50
–60
–70
–80
–90
–100
100
10
1
G = +1
G = +2
V
= ±12V
S
0.1
0.01
0
V
= ±5V
S
0.1
1
10
FREQUENCY (MHz)
100
100
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 34. CMRR vs. Frequency (See Figure 46)
Figure 37. Output Impedance vs. Frequency (See Figure 45 and Figure 47)
0.30
0.25
0.20
0.15
0.10
0.05
0
80
70
V
– V
OH
CC
V
– V
OH
CC
60
50
40
30
V
– V
EE
OL
V
– V
EE
OL
0
10
20
30
40
25
35
45
55
65
75
85
TEMPERATURE (°C)
I
(mA)
LOAD
Figure 38. Output Saturation Voltage vs. Temperature
Figure 35. Output Saturation Voltage vs. Output Load Current
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
V
= 2V p-p
IN
G = +1
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–PSRR
+PSRR
B TO A
A TO B
0.01
0.1
1
10
100
1000
0.1
1
10
FREQUENCY (MHz)
100
FREQUENCY (MHz)
Figure 36. PSRR vs. Frequency (See Figure 48 and Figure 50)
Figure 39. Crosstalk vs. Frequency (See Figure 51)
Rev. G | Page 13 of 28
AD8065/AD8066
6.60
125
120
115
110
105
100
95
V
= ±12V
S
6.55
6.50
6.45
6.40
6.35
6.30
6.25
V
= ±5V
S
V
= ±12V
S
V
= +5V
S
V
= +5V
S
V
= ±5V
S
90
85
80
–40
–20
0
20
40
60
80
0
10
20
(mA)
30
40
TEMPERATURE (°C)
I
LOAD
Figure 40. Quiescent Supply Current vs. Temperature for Various
Supply Voltages
Figure 41. Open-Loop Gain vs. Load Current for Various Supply Voltages
Rev. G | Page 14 of 28
AD8065/AD8066
TEST CIRCUITS
SOIC-8 Pinout
+V
CC
+V
CC
4.7μF
0.1μF
4.7μF
0.1μF
2.2pF
24.9Ω
499Ω
499Ω
V
IN
49.9Ω
FET PROBE
FET PROBE
R
SNUB
AD8065
AD8065
V
IN
249Ω
C
LOAD
1kΩ
1kΩ
49.9Ω
0.1μF
4.7μF
0.1μF
4.7μF
–V
EE
–V
EE
Figure 44. G = −1
Figure 42. G = +1
+V
CC
+V
CC
4.7μF
0.1μF
4.7μF
0.1μF
2.2pF
24.9Ω
499Ω
499Ω
FET PROBE
R
SNUB
AD8065
AD8065
V
IN
NETWORK ANALYZER S22
249Ω
C
1kΩ
LOAD
0.1μF
4.7μF
49.9Ω
0.1μF
4.7μF
–V
EE
–V
EE
Figure 43. G = +2
Figure 45. Output Impedance G = +1
Rev. G | Page 15 of 28
AD8065/AD8066
+V
CC
V
IN
1V p-p
4.7μF
0.1μF
+V
CC
49.9Ω
24.9Ω
499Ω
499Ω
V
IN
FET PROBE
FET PROBE
AD8065
AD8065
49.9Ω
499Ω
1kΩ
1kΩ
0.1μF
4.7μF
0.1μF
4.7μF
499Ω
–V
EE
–V
EE
Figure 46. CMRR
Figure 48. Positive PSRR
+V
CC
+V
CC
4.7μF
4.7μF
0.1μF
0.1μF
2.2pF
499Ω
499Ω
499Ω
499Ω
AD8065
249Ω
NETWORK ANALYZER
S22
976Ω
TO SCOPE
AD8065
249Ω
V
IN
0.1μF
49.9Ω
0.1μF
49.9Ω
4.7μF
4.7μF
–V
EE
–V
EE
Figure 49. Settling Time
Figure 47. Output Impedance G = +2
Rev. G | Page 16 of 28
AD8065/AD8066
24.9Ω
+V
CC
4.7μF
0.1μF
FET PROBE
24.9Ω
AD8066
24.9Ω
+5V
1kΩ
4.7μF
0.1μF
RECEIVE SIDE
FET PROBE
AD8065
AD8066
V
IN
1kΩ
0.1μF
49.9Ω
1kΩ
49.9Ω
4.7μF
V
IN
1V p-p
–5V
DRIVE SIDE
–V
EE
Figure 50. Negative PSRR
Figure 51. Crosstalk—AD8066
2.2pF
499Ω
499Ω
5V
4.7μF
1.5V
0.1μF
FET PROBE
AD8065
249Ω
V
IN
1kΩ
49.9Ω
1.5V
1.5V
Figure 52. Single Supply
Rev. G | Page 17 of 28
AD8065/AD8066
THEORY OF OPERATION
The AD8065/AD8066 are voltage feedback operational
amplifiers that combine a laser-trimmed JFET input stage with
the Analog Devices eXtra Fast Complementary Bipolar (XFCB)
process, resulting in an outstanding combination of precision
and speed. The supply voltage range is from 5 V to 24 V. The
amplifiers feature a patented rail-to-rail output stage capable of
driving within 0.5 V of either power supply while sourcing or
sinking up to 30 mA. Also featured is a single-supply input stage
that handles common-mode signals from below the negative
supply to within 3 V of the positive rail. Operation beyond the
JFET input range is possible because of an auxiliary bipolar input
stage that functions with input voltages up to the positive supply.
The amplifiers operate as if they have a rail-to-rail input and
exhibit no phase reversal behavior for common-mode voltages
within the power supply.
NONINVERTING CLOSED-LOOP FREQUENCY
RESPONSE
Solving for the transfer function
2π× fcrossover
RG + RF
( )
VO
VI
=
(
RF + RG s + 2π× fcrossover × RG
)
where fcrossover is the frequency where the amplifier’s open-loop
gain equals 0 db
VO RF + RG
At dc
=
VI
RG
Closed-loop −3 dB frequency
RG
RF + RG
f−3dB = fcrossover
×
With voltage noise of 7 nV/√Hz and −88 dBc distortion for
1 MHz, 2 V p-p signals, the AD8065/AD8066 are a great choice
for high resolution data acquisition systems. Their low noise,
sub-pA input current, precision offset, and high speed make
them superb preamps for fast photodiode applications. The
speed and output drive capability of the AD8065/AD8066 also
make them useful in video applications.
INVERTING CLOSED-LOOP FREQUENCY
RESPONSE
−2π× fcrossover × RF
RF + RG + 2π× fcrossover × RG
VO
VI
=
s
(
)
VO
VI
RF
RG
At dc
= −
CLOSED-LOOP FREQUENCY RESPONSE
Closed-loop −3 dB frequency
The AD8065/AD8066 are classic voltage feedback amplifiers
with an open-loop frequency response that can be approx-
imated as the integrator response shown in Figure 53. Basic
closed-loop frequency response for inverting and noninverting
configurations can be derived from the schematics shown.
RG
f−3dB = fcrossover
×
RF + RG
R
F
R
F
R
G
R
G
V
I
V
V
O
O
V
A
A
V
E
E
V
I
80
A = (2π × fcrossover)/s
60
40
20
0
fcrossover = 65MHz
0.01
0.1
1
10
100
FREQUENCY (MHz)
Figure 53. Open-Loop Gain vs. Frequency and Basic Connections
Rev. G | Page 18 of 28
AD8065/AD8066
The closed-loop bandwidth is inversely proportional to the
noise gain of the op amp circuit, (RF + RG )/RG. This simple
model is accurate for noise gains above 2. The actual bandwidth
of circuits with noise gains at or below 2 are higher than those
predicted with this model due to the influence of other poles in
the frequency response of the real op amp.
For the best settling times and the best distortion, the
impedances at the AD8065/AD8066 input terminals should be
matched. This minimizes nonlinear common-mode capacitive
effects that can degrade ac performance.
Actual distortion performance depends on a number of
variables:
R
F
•
•
•
•
•
The closed-loop gain of the application
Whether it is inverting or noninverting
Amplifier loading
Signal frequency and amplitude
Board layout
+V
OS
–
R
G
V
O
I
I
A
b
–
R
S
V
I
b+
Also see Figure 16 to Figure 20. The lowest distortion is
obtained with the AD8065 used in low gain inverting appli-
cations, since this eliminates common-mode effects. Higher
closed-loop gains result in worse distortion performance.
Figure 54. Voltage Feedback Amplifier DC Errors
Figure 54 shows a voltage feedback amplifier’s dc errors. For
both inverting and noninverting configurations
INPUT PROTECTION
The inputs of the AD8065/AD8066 are protected with back-to-
back diodes between the input terminals as well as ESD diodes
to either power supply. This results in an input stage with
picoamps of input current that can withstand up to 1500 V ESD
events (human body model) with no degradation.
R + R
RG
R + R
RG
⎛
⎜
⎞
⎟
⎛
⎜
⎞
⎟
G
F
G
F
VO
(
error
)
= Ib+ × RS
− I × RF +VOS
b−
⎝
⎠
⎝
⎠
The voltage error due to Ib+ and Ib– is minimized if RS = RF || RG
(though with the AD8065 input currents at less than 20 pA over
temperature, this is likely not a concern). To include common-
mode and power supply rejection effects, total VOS can be
modeled
Excessive power dissipation through the protection devices
destroys or degrades the performance of the amplifier. Differ-
ential voltages greater than 0.7 V result in an input current of
approximately (|V+ − V−| 0.7 V)/RI, where RI is the resistance in
series with the inputs.
ΔVS ΔVCM
PSR CMR
VOS =VOS
+
+
nom
VOS
is the offset voltage specified at nominal conditions,
For input voltages beyond the positive supply, the input current
is approximately (VI − VCC − 0.7)/RI. Beyond the negative
supply, the input current is about (VI − VEE + 0.7)/RI. If the
inputs of the amplifier are to be subjected to sustained
differential voltages greater than 0.7 V, or to input voltages
beyond the amplifier power supply, input current should be
limited to 30 mA by an appropriately sized input resistor (RI), as
shown in Figure 55.
nom
ΔVS is the change in power supply from nominal conditions,
PSR is the power supply rejection, ΔVCM is the change in
common-mode voltage from nominal conditions, and CMR is
the common-mode rejection.
WIDEBAND OPERATION
Figure 42 through Figure 44 show the circuits used for
wideband characterization for gains of +1, +2, and −1. Source
impedance at the summing junction (RF || RG) will form a pole
in the amplifier’s loop response with the amplifier’s input
capacitance of 6.6 pF. This can cause peaking and ringing if the
time constant formed is too low. Feedback resistances of 300 Ω
to 1 kΩ are recommended, since they will not unduly load
down the amplifier and the time constant formed will not be
too low. Peaking in the frequency response can be compensated
for with a small capacitor (CF) in parallel with the feedback
resistor, as illustrated in Figure 12. This shows the effect of
different feedback capacitances on the peaking and bandwidth
for a noninverting G = +2 amplifier.
(V – V – 0.7V)
(| V – V | – 0.7V)
I
EE
+
–
R >
I
R >
I
30mA
30mA
(V – V + 0.7V)
I
EE
FOR LARGE | V – V
+
|
R >
I
–
30mA
FOR V BEYOND
SUPPLY VOLTAGES
AD8065
I
R
I
V
I
V
O
Figure 55. Current-Limiting Resistor
Rev. G | Page 19 of 28
AD8065/AD8066
The circuit is arranged such that when the input common-
mode voltage exceeds a certain threshold, the input JFET pair’s
bias current turns OFF, and the bias current of an auxiliary
NPN pair turns ON, taking over control of the amplifier. When
the input common-mode voltage returns to a viable operating
value, the FET stage turns back ON, the NPN stage turns OFF,
and normal operation resumes.
THERMAL CONSIDERATIONS
With 24 V power supplies and 6.5 mA quiescent current, the
AD8065 dissipates 156 mW with no load. The AD8066
dissipates 312 mW. This can lead to noticeable thermal effects,
especially in the small SOT-23-5 (thermal resistance of
160°C/W). VOS temperature drift is trimmed to guarantee a
maximum drift of 17 μV/°C, so it can change up to 0.425 mV
due to warm-up effects for an AD8065/AD8066 in a SOT-23-5
package on 24 V.
The NPN pair can sustain operation with the input voltage up
to the positive supply, so this is a pseudo rail-to-rail input stage.
For operation beyond the FET stage’s common-mode limit, the
amplifier’s VOS changes to the NPN pair’s offset (mean of
160 μV, standard deviation of 820 μV), and Ib increases to the
NPN pair’s base current up to 45 μA (see Figure 32).
Ib increases by a factor of 1.7 for every 10°C rise in temperature.
Ib is close to five times higher at 24 V supplies as opposed to a
single 5 V supply.
Heavy loads increase power dissipation and raise the chip
junction temperature as described in the Maximum Power
Dissipation section. Care should be taken to not exceed the
rated power dissipation of the package.
Switchback, or recovery time, is about 100 ns, see Figure 27.
The output transistors of the rail-to-rail output stage have
circuitry to limit the extent of their saturation when the output
is overdriven. This helps output recovery time. Output recovery
from a 0.5 V output overdrive on a 5 V supply is shown in
Figure 24.
INPUT AND OUTPUT OVERLOAD BEHAVIOR
The AD8065/AD8066 have internal circuitry to guard against
phase reversal due to overdriving the input stage. A simplified
schematic of the input stage, including the input-protection
diodes and antiphase reversal circuitry, is shown in Figure 56.
V
CC
R1
R5
TO REST OF AMP
Q2
Q5
V
THRESHOLD
VBIAS
D1
D2
R6
R3
Q1
Q6
V
V
N
P
D3
D4
Q3
Q4
S
S
R4
R7
R2
R8
Q7
I
I
T2
T1
–V
EE
Figure 56. Simplified Input Stage
Rev. G | Page 20 of 28
AD8065/AD8066
LAYOUT, GROUNDING, AND BYPASSING CONSIDERATIONS
POWER SUPPLY BYPASSING
GROUNDING
Power supply pins are actually inputs and care must be taken so
that a noise-free stable dc voltage is applied. The purpose of
bypass capacitors is to create low impedances from the supply
to ground at all frequencies, thereby shunting or filtering most
of the noise.
A ground plane layer is important in densely packed PC boards
to spread the current minimizing parasitic inductances.
However, an understanding of where the current flows in a
circuit is critical to implementing effective high speed circuit
design. The length of the current path is directly proportional to
the magnitude of parasitic inductances and, therefore, the high
frequency impedance of the path. High speed currents in an
inductive ground return create unwanted voltage noise.
Decoupling schemes are designed to minimize the bypassing
impedance at all frequencies with a parallel combination of
capacitors. 0.1 μF (X7R or NPO) chip capacitors are critical and
should be as close as possible to the amplifier package. The
4.7 μF tantalum capacitor is less critical for high frequency
bypassing, and, in most cases, only one is needed per board at
the supply inputs.
The length of the high frequency bypass capacitor leads is most
critical. A parasitic inductance in the bypass grounding works
against the low impedance created by the bypass capacitor.
Place the ground leads of the bypass capacitors at the same
physical location. Because load currents flow from the supplies
as well, the ground for the load impedance should be at the
same physical location as the bypass capacitor grounds. For the
larger value capacitors, which are effective at lower frequencies,
the current return path distance is less critical.
Rev. G | Page 21 of 28
AD8065/AD8066
enough. It is recommended that the external passive
components connected to the input pins be placed as close as
possible to the inputs to avoid parasitic capacitance. The ground
and power planes must be kept at a small distance from the
input pins on all layers of the board.
LEAKAGE CURRENTS
Poor PC board layout, contaminants, and the board insulator
material can create leakage currents that are much larger than
the input bias current of the AD8065/AD8066. Any voltage
differential between the inputs and nearby runs sets up leakage
currents through the PC board insulator, for example,
1 V/100 GΩ = 10 pA. Similarly, any contaminants on the board
can create significant leakage (skin oils are a common problem).
To significantly reduce leakage, put a guard ring (shield) around
the inputs and input leads that are driven to the same voltage
potential as the inputs. This way there is no voltage potential
between the inputs and surrounding area to set up any leakage
currents. For the guard ring to be completely effective, it must
be driven by a relatively low impedance source and should
completely surround the input leads on all sides, above and
below, using a multilayer board.
OUTPUT CAPACITANCE
To a lesser extent, parasitic capacitances on the output can cause
peaking and ringing of the frequency response. There are two
methods to effectively minimize their effect:
•
•
As shown in Figure 57, put a small value resistor (RS) in
series with the output to isolate the load capacitor from the
amp’s output stage. A good value to choose is 20 Ω (see
Figure 10).
Increase the phase margin with higher noise gains or add a
pole with a parallel resistor and capacitor from −IN to the
output.
Another effect that can cause leakage currents is the charge
absorption of the insulator material itself. Minimizing the
amount of material between the input leads and the guard ring
helps to reduce the absorption. Also, low absorption materials,
such as Teflon® or ceramic, could be necessary in some
instances.
R
= 20Ω
S
V
AD8065
O
C
V
L
I
INPUT CAPACITANCE
Along with bypassing and ground, high speed amplifiers can be
sensitive to parasitic capacitance between the inputs and
Figure 57. Output Isolation Resistor
ground. A few pF of capacitance reduces the input impedance at
high frequencies, in turn increasing the amplifier’s gain, causing
peaking of the frequency response or even oscillations, if severe
C
F
R
F
11
= 10 Ω
SH
C
C
I
R
M
PHOTO
C
S
C
D
V
M
O
V
B
C
+ C
S
F
R
F
Figure 58. Wideband Photodiode Preamp
Rev. G | Page 22 of 28
AD8065/AD8066
bandwidth in half results in a flat frequency response with
about 5% transient overshoot.
INPUT-TO-OUTPUT COUPLING
To minimize capacitive coupling between the inputs and output,
the output signal traces should not be parallel with the inputs.
The preamp’s output noise over frequency is shown in Figure 59.
WIDEBAND PHOTODIODE PREAMP
1
Figure 58 shows an I/V converter with an electrical model of a
photodiode. The basic transfer function is
f1
=
2πR (C + C + C + 2C
)
F
F
S
M
D
1
f2
f3
=
=
2πR C
IPHOTO × RF
1+ sCF RF
F
F
VOUT
=
fCR
(C + C + 2C + C )/C
F
S
M
D
F
where IPHOTO is the output current of the photodiode, and the
parallel combination of RF and CF sets the signal bandwidth.
R
NOISE
F
The stable bandwidth attainable with this preamp is a function
of RF, the gain bandwidth product of the amplifier, and the total
capacitance at the amplifier’s summing junction, including CS
and the amplifier input capacitance. RF and the total capacitance
produce a pole in the amplifier’s loop transmission that can
result in peaking and instability. Adding CF creates a 0 in the
loop transmission that compensates for the pole’s effect and
reduces the signal bandwidth. It can be shown that the signal
bandwidth resulting in a 45° phase margin (f(45)) is defined by
f3
f2
VEN (C + C + C + 2C )/C
F
F
S
M
D
f1
VEN
NOISE DUE TO AMPLIFIER
FREQUENCY (Hz)
Figure 59. Photodiode Voltage Noise Contributions
The pole in the loop transmission translates to a 0 in the
amplifier’s noise gain, leading to an amplification of the input
voltage noise over frequency. The loop transmission 0
introduced by CF limits the amplification. The noise gain
bandwidth extends past the preamp signal bandwidth and is
eventually rolled off by the decreasing loop gain of the
amplifier. Keeping the input terminal impedances matched is
recommended to eliminate common-mode noise peaking
effects, which adds to the output noise.
fCR
f(
=
)
45
2π× RF ×CS
where fCR is the amplifier crossover frequency, RF is the feedback
resistor, and CS is the total capacitance at the amplifier summing
junction (amplifier + photodiode + board parasitics).
The value of CF that produces f(45) can be shown to be
Integrating the square of the output voltage noise spectral
density over frequency and then taking the square root allows
users to obtain the total rms output noise of the preamp. Table 5
summarizes approximations for the amplifier and feedback and
source resistances. Noise components for an example preamp
with RF = 50 kΩ, CS = 15 pF, and CF = 2 pF (bandwidth of about
1.6 MHz) are also listed.
CS
CF =
2π× RF × fCR
The frequency response in this case shows about 2 dB of
peaking and 15% overshoot. Doubling CF and cutting the
Table 5. RMS Noise Contributions of Photodiode Preamp
RMS Noise with RF = 50 kΩ,
CS = 15 pF, CS = 15 pF
Contributor
Expression
64.5 μV
2.4 μV
31 μV
RF (×2)
2 × 4 kT × RF × f2 ×1.57
Amp to f1
VEN × f1
Amp (f2 – f1)
CS +CM +CF +2CD
VEN ×
×
f2 − f1
CF
Amp to (past f2)
260 μV
CS +CM +CD +2CF
VEN ×
×
f3 ×1.57
CF
270 μV (Total)
Rev. G | Page 23 of 28
AD8065/AD8066
V
CC
4.7μF
0.1μF
R
S1
1
/
2
V
N
2.2pF
AD8066
4.7μF
R2
0.1μF
500Ω
V
V
CC
EE
4.7μF
0.1μF
R1
500Ω
R
= 500Ω
F
V
O
AD8065
R
G
4.7μF
0.1μF
R3
V
R
= 500Ω
500Ω
EE
F
V
CC
4.7μF
0.1μF
R4
500Ω
2.2pF
1
/
2
AD8066
R
S2
V
P
4.7μF
0.1μF
V
EE
Figure 60. High Speed Instrumentation Amplifier
HIGH SPEED JFET INPUT INSTRUMENTATION
AMPLIFIER
VIDEO BUFFER
The output current capability and speed of the AD8065 make it
useful as a video buffer, shown in Figure 61.
Figure 60 shows an example of a high speed instrumentation
amplifier with high input impedance using the
AD8065/AD8066. The dc transfer function is
The G = +2 configuration compensates for the voltage division
of the signal due to the signal termination. This buffer maintains
0.1 dB flatness for signals up to 7 MHz, from low amplitudes up
to 2 V p-p (see Figure 7). Differential gain and phase have been
measured to be 0.02% and 0.028°, respectively, at 5 V supplies.
1+1000
RG
⎛
⎜
⎞
⎟
VOUT
= VN −VP
( )
⎝
⎠
For G = +1, it is recommended that the feedback resistors for
the two preamps be set to a low value (for instance 50 Ω for
50 Ω source impedance). The bandwidth for G = +1 is 50 MHz.
For higher gains, the bandwidth is set by the preamp, equaling
+V
S
4.7μF
4.7μF
0.1μF
249Ω
75Ω
+
AD8065
V
–
I
+
Inamp−3dB
=
f
CR × RG
/
2 × RF
V
–
75Ω
O
0.1μF
Common-mode rejection of the in-amp will be primarily
determined by the match of the resistor ratios R1:R2 to R3:R4.
It can be estimated
–V
S
2.2pF
VO
VCM
(
δ1− δ2
)
499Ω
499Ω
=
(
1+ δ1
)
δ2
Figure 61. Video Buffer
The summing junction impedance for the preamps is equal to
RF || 0.5(RG). This is the value to be used for matching purposes.
Rev. G | Page 24 of 28
AD8065/AD8066
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
3.20
3.00
2.80
8
1
5
4
6.20 (0.2440)
5.80 (0.2284)
4.00 (0.1574)
3.80 (0.1497)
8
1
5
4
5.15
4.90
4.65
3.20
3.00
2.80
1.27 (0.0500)
BSC
0.50 (0.0196)
0.25 (0.0099)
× 45°
1.75 (0.0688)
1.35 (0.0532)
PIN 1
0.25 (0.0098)
0.10 (0.0040)
0.65 BSC
8°
0.95
0.85
0.75
0.51 (0.0201)
0.31 (0.0122)
0° 1.27 (0.0500)
COPLANARITY
0.10
0.25 (0.0098)
0.17 (0.0067)
1.10 MAX
SEATING
PLANE
0.40 (0.0157)
0.80
0.60
0.40
8°
0°
0.15
0.00
0.38
0.22
COMPLIANT TO JEDEC STANDARDS MS-012AA
0.23
0.08
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
SEATING
PLANE
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 62. 8-Lead Standard Small Outline Package [SOIC]
Narrow Body (R-8)
Figure 64. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters and (inches)
Dimensions shown in millimeters
2.90 BSC
5
1
4
3
2.80 BSC
1.60 BSC
2
PIN 1
0.95 BSC
1.90
BSC
1.30
1.15
0.90
1.45 MAX
0.22
0.08
10°
5°
0°
0.15 MAX
0.50
0.30
0.60
0.45
0.30
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-178-AA
Figure 63. 5-Lead Small Outline Transistor Package [SOT-23]
(RT-5)
Dimensions shown in millimeters
Rev. G | Page 25 of 28
AD8065/AD8066
ORDERING GUIDE
Model
AD8065AR
AD8065AR-REEL
AD8065AR-REEL7
AD8065ARZ1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
8-Lead SOIC
8-Lead SOIC
8-Lead SOIC
8-Lead SOIC
Package Option
R-8
R-8
R-8
R-8
Branding
AD8065ARZ-REEL1
AD8065ARZ-REEL71
AD8065ART-REEL
AD8065ART-R2
AD8065ART-REEL7
AD8065ARTZ-R22
AD8065ARTZ-REEL2
AD8065ARTZ-REEL72
AD8066AR
AD8066AR-REEL
AD8066AR-REEL7
AD8066ARZ1
AD8066ARZ-RL1
AD8066ARZ-R71
AD8066ARM
8-Lead SOIC
8-Lead SOIC
R-8
R-8
5-Lead SOT-23
5-Lead SOT-23
5-Lead SOT-23
5-Lead SOT-23
5-Lead SOT-23
5-Lead SOT-23
8-Lead SOIC
8-Lead SOIC
8-Lead SOIC
8-Lead SOIC
8-Lead SOIC
RT-5
RT-5
RT-5
RT-5
RT-5
RT-5
R-8
R-8
R-8
R-8
R-8
HRA
HRA
HRA
HRA #
HRA #
HRA #
8-Lead SOIC
R-8
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
RM-8
RM-8
RM-8
RM-8
RM-8
H1B
H1B
H1B
H7C
H7C
AD8066ARM-REEL
AD8066ARM-REEL7
AD8066ARMZ1
AD8066ARMZ-REEL71
1 Z = Pb-free part.
2 Z = Pb-free part, # denotes lead-free product, may be top or bottom marked.
Rev. G | Page 26 of 28
AD8065/AD8066
NOTES
Rev. G | Page 27 of 28
AD8065/AD8066
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C02916-0-1/06(G)
Rev. G | Page 28 of 28
相关型号:
©2020 ICPDF网 联系我们和版权申明