AD8041AR [ADI]
160 MHz Rail-to-Rail Amplifier with Disable; 160 MHz的轨到轨放大器禁用型号: | AD8041AR |
厂家: | ADI |
描述: | 160 MHz Rail-to-Rail Amplifier with Disable |
文件: | 总16页 (文件大小:440K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
160 MHz Rail-to-Rail
Amplifier with Disable
a
AD8041
CONNECTION DIAGRAM
FEATURES
8-Pin Plastic Mini-DIP and SOIC
Fully Specified for +3 V, +5 V, and ؎5 V Supplies
Output Swings Rail to Rail
Input Voltage Range Extends 200 mV Below Ground
No Phase Reversal with Inputs 1 V Beyond Supplies
Disable/Power-Down Capability
Low Power of 5.2 mA (26 mW on +5 V)
High Speed and Fast Settling on +5 V:
160 MHz –3 dB Bandwidth (G = +1)
160 V/s Slew Rate
NC
–INPUT
+INPUT
1
2
3
4
8
7
6
5
DISABLE
+V
S
OUTPUT
NC
AD8041
(Top View)
–V
S
NC = NO CONNECT
30 ns Settling Time to 0.1%
Good Video Specifications (RL = 150 ⍀, G = +2)
Gain Flatness of 0.1 dB to 30 MHz
0.03% Differential Gain Error
0.03؇ Differential Phase Error
Low Distortion
–69 dBc Worst Harmonic @ 10 MHz
Outstanding Load Drive Capability
Drives 50 mA 0.5 V from Supply Rails
Cap Load Drive of 45 pF
The output voltage swing extends to within 50 mV of each rail,
providing the maximum output dynamic range. Additionally, it
features gain flatness of 0.1 dB to 30 MHz while offering differ-
ential gain and phase error of 0.03% and 0.03° on a single +5 V
supply. This makes the AD8041 ideal for professional video
electronics such as cameras, video switchers or any high speed
portable equipment. The AD8041’s low distortion and fast set-
tling make it ideal for buffering high speed A-to-D converters.
The AD8041 has a high speed disable feature useful for mul-
tiplexing or for reducing power consumption (1.5 mA). The dis-
able logic interface is compatible with CMOS or open-collector
logic. The AD8041 offers low power supply current of 5.8 mA
max and can run on a single +3 V power supply. These features
are ideally suited for portable and battery powered applications
where size and power are critical.
APPLICATIONS
Power Sensitive High Speed Systems
Video Switchers
Distribution Amplifiers
A/D Driver
Professional Cameras
CCD Imaging Systems
Ultrasound Equipment (Multichannel)
Single-Supply Multiplexer
The wide bandwidth of 160 MHz along with 160 V/µs of slew
rate on a single +5 V supply make the AD8041 useful in many
general purpose high speed applications where dual power sup-
plies of up to ±6 V and single supplies from +3 V to +12 V are
needed. The AD8041 is available in 8-pin plastic DIP and
SOIC over the industrial temperature range of –40°C to +85°C.
PRODUCT DESCRIPTION
The AD8041 is a low power voltage feedback, high speed am-
plifier designed to operate on +3 V, +5 V or ±5 V supplies. It
has true single supply capability with an input voltage range
extending 200 mV below the negative rail and within 1 V of the
positive rail.
+2
V
= +5V
S
+1
0
G = +2
= 400Ω
R
F
–1
–2
–3
–4
–5
–6
5V
2.5V
0V
–7
–8
1V
200ns
40
FREQUENCY – MHz
80
100
0
60
20
Figure 1. Output Swing: Gain = –1, VS = +5 V
REV. 0
Figure 2. Frequency Response: Gain = +2, VS = +5 V
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
© Analog Devices, Inc., 1995
One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
AD8041–SPECIFICATIONS(@ TA = +25؇C, VS = +5 V, RL = 2 kΩ to 2.5 V, unless otherwise noted)
AD8041A
Parameter
Conditions
Min
Typ
Max
Units
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth, VO < 0.5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Full Power Response
Settling Time to 0.1%
G = +1
130
130
160
30
160
24
MHz
MHz
V/µs
MHz
ns
G = +2, RL = 150 Ω
G = –1, VO = 2 V Step
VO = 2 V p-p
G = –1, VO = 2 V Step
35
Settling Time to 0.01%
55
ns
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Input Voltage Noise
Input Current Noise
Differential Gain Error (NTSC)
Differential Phase Error (NTSC)
fC = 5 MHz, VO = 2 V p-p, G = +2, RL = 1 kΩ
f = 10 kHz
f = 10 kHz
G = +2, RL = 150 Ω to 2.5 V
G = +2, RL = 150 Ω to 2.5 V
G = +2, RL = 75 Ω to 2.5 V
G = +2, RL = 75 Ω to 2.5 V
–72
16
dB
nV/√Hz
fA/√Hz
%
Degrees
%
600
0.03
0.03
0.01
0.19
Degrees
DC PERFORMANCE
Input Offset Voltage
2
7
8
mV
mV
µV/°C
µA
TMIN–TMAX
Offset Drift
Input Bias Current
10
1.2
2
TMIN–TMAX
3
µA
Input Offset Current
Open-Loop Gain
0.2
95
90
0.5
µA
dB
dB
RL = 1 kΩ
TMIN–TMAX
86
74
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
160
1.8
–0.2 to 4
80
kΩ
pF
V
VCM = 0 V to 3.5 V
dB
OUTPUT CHARACTERISTICS
Output Voltage Swing: RL = 10 kΩ
Output Voltage Swing: RL = 1 kΩ
Output Voltage Swing: RL = 50 Ω
Output Current
0.05 to 4.95
0.35 to 4.75 0.1 to 4.9
V
V
V
mA
mA
mA
pF
0.4 to 4.4
0.3 to 4.5
50
90
150
45
VOUT = 0.5 V to 4.5 V
Sourcing
Sinking
Short Circuit Current
Capacitive Load Drive
G = +1
POWER SUPPLY
Operating Range
3
12
V
Quiescent Current
Quiescent Current (Disabled)
Power Supply Rejection Ratio
5.2
1.4
80
5.8
1.7
mA
mA
dB
VS = 0, +5 V, ±1 V
72
DISABLE CHARACTERISTICS
Turn-Off Time
Turn-On Time
Off Isolation (Pin 8 Tied to –VS)
Off Voltage (Device Disabled)
On Voltage (Device Enabled)
VO = 2 V p-p @ 10 MHz, G = + 2
RF = RL = 2 kΩ
RF = RL = 2 kΩ
120
230
70
<+VS – 0.25
Open or +VS
ns
ns
dB
V
RL = 100 Ω, f = 5 MHz, G = +2, RF = 1 kΩ
V
Specifications subject to change without notice.
–2–
REV. 0
AD8041
(@ T = +25؇C, V = +3 V, R = 2 kΩ to 1.5 V, unless otherwise noted)
SPECIFICATIONS
A
S
L
AD8041A
Typ
Parameter
Conditions
Min
Max
Units
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth, VO < 0.5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Full Power Response
Settling Time to 0.1%
G = +1
120
120
150
25
150
20
MHz
MHz
V/µs
MHz
ns
G = +2, RL = 150 Ω
G = –1, VO = 2 V Step
VO = 2 V p-p
G = –1, VO = 2 V Step
40
Settling Time to 0.01%
55
ns
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Input Voltage Noise
Input Current Noise
Differential Gain Error (NTSC)
Differential Phase Error (NTSC)
fC = 5 MHz, VO = 2 V p-p, G = –1, RL = 100 Ω
f = 10 kHz
f = 10 kHz
G = +2, RL = 150 Ω to 1.5 V, Input VCM = 1 V
G = +2, RL = 150 Ω to 1.5 V, Input VCM = 1 V
–55
16
600
0.07
0.05
dB
nV/√Hz
fA/√Hz
%
Degrees
DC PERFORMANCE
Input Offset Voltage
2
7
8
mV
mV
µV/°C
µA
TMIN–TMAX
Offset Drift
Input Bias Current
10
1.2
2.3
3
TMIN–TMAX
µA
Input Offset Current
Open-Loop Gain
0.2
94
89
0.6
µA
dB
dB
RL = 1 kΩ
TMIN–TMAX
85
72
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
160
1.8
–0.2 to 2
kΩ
pF
V
VCM = 0 V to 1.5 V
80
dB
OUTPUT CHARACTERISTICS
Output Voltage Swing: RL = 10 kΩ
Output Voltage Swing: RL = 1 kΩ
Output Voltage Swing: RL = 50 Ω
Output Current
0.05 to 2.95
0.45 to 2.7 0.1 to 2.9
V
V
V
mA
mA
mA
pF
0.5 to 2.6
0.25 to 2.75
50
70
120
40
VOUT = 0.5 V to 2.5 V
Sourcing
Sinking
Short Circuit Current
Capacitive Load Drive
G = +1
POWER SUPPLY
Operating Range
3
12
V
Quiescent Current
Quiescent Current (Disabled)
Power Supply Rejection Ratio
5.0
1.3
80
5.6
1.5
mA
mA
dB
VS = 0, +3 V, ±0.5 V
68
DISABLE CHARACTERISTICS
Turn-Off Time
Turn-On Time
Off Isolation (Pin 8 Tied to –VS)
Off Voltage (Device Disabled)
On Voltage (Device Enabled)
VO = 2 V p-p @ 10 MHz, G = +2
RF = RL = 2 kΩ
RF = RL = 2 kΩ
90
170
70
<+VS – 0.25
Open or +VS
ns
ns
dB
V
RL = 100 Ω, f = 5 MHz, G = +2, RF = 1 kΩ
V
Specifications subject to change without notice.
REV. 0
–3–
AD8041–SPECIFICATIONS(@ TA = +25؇C, VS = ؎5 V, RL = 2 kΩ to 0 V, unless otherwise noted)
AD8041A
Parameter
Conditions
Min
Typ
Max
Units
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth, VO < 0.5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Full Power Response
Settling Time to 0.1%
G = +1
140
140
170
32
170
26
MHz
MHz
V/µs
MHz
ns
G = +2, RL = 150 Ω
G = –1, VO = 2 V Step
VO = 2 V p-p
G = –1, VO = 2 V Step
30
Settling Time to 0.01%
50
ns
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Input Voltage Noise
Input Current Noise
Differential Gain Error (NTSC)
Differential Phase Error (NTSC)
fC = 5 MHz, VO = 2 V p-p, G = +2, RL = 1 kΩ
f = 10 kHz
f = 10 kHz
G = +2, RL = 150 Ω
G = +2, RL = 150 Ω
G = +2, RL = 75 Ω
–77
16
dB
nV/√Hz
fA/√Hz
%
Degrees
%
600
0.02
0.03
0.02
0.10
G = +2, RL = 75 Ω
Degrees
DC PERFORMANCE
Input Offset Voltage
2
7
8
mV
mV
µV/°C
µA
TMIN–TMAX
Offset Drift
Input Bias Current
10
1.2
2.3
3
TMIN–TMAX
µA
Input Offset Current
Open-Loop Gain
0.2
99
95
0.6
µA
dB
dB
RL = 1 kΩ
TMIN–TMAX
90
72
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
160
1.8
–5.2 to 4
80
kΩ
pF
V
VCM = –5 V to 3.5 V
dB
OUTPUT CHARACTERISTICS
Output Voltage Swing: RL = 10 kΩ
Output Voltage Swing: RL = 1 kΩ
Output Voltage Swing: RL = 50 Ω
Output Current
–4.95 to +4.95
–4.8 to +4.8
–4.5 to +3.8
50
100
160
50
V
V
V
mA
mA
mA
pF
–4.45 to +4.6
–4.3 to +3.2
VOUT = –4.5 V to 4.5 V
Sourcing
Sinking
Short Circuit Current
Capacitive Load Drive
G = +1
POWER SUPPLY
Operating Range
3
12
V
Quiescent Current
Quiescent Current (Disabled)
Power Supply Rejection Ratio
5.8
1.6
80
6.5
2.2
mA
mA
dB
VS = –5, +5 V, ±1 V
68
DISABLE CHARACTERISTICS
Turn-Off Time
Turn-On Time
Off Isolation (Pin 8 Tied to –VS)
Off Voltage (Device Disabled)
On Voltage (Device Enabled)
VO = 2 V p-p @ 10 MHz, G = +2
RF = 2 kΩ
RF = 2 kΩ
120
320
70
<+VS – 0.25V
Open or +VS
ns
ns
dB
RL = 100 Ω, f = 5 MHz, G = +2, RF = 1 kΩ
Specifications subject to change without notice.
–4–
REV. 0
AD8041
ABSOLUTE MAXIMUM RATINGS1
MAXIMUM POWER DISSIPATION
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +12.6 V
The maximum power that can be safely dissipated by the
AD8041 is limited by the associated rise in junction tempera-
ture. The maximum safe junction temperature for plastic encap-
sulated devices is determined by the glass transition temperature
of the plastic, approximately +150°C. Exceeding this limit tem-
porarily may cause a shift in parametric performance due to a
change in the stresses exerted on the die by the package. Ex-
ceeding a junction temperature of +175°C for an extended pe-
riod can result in device failure.
Internal Power Dissipation2
Plastic Package (N) . . . . . . . . . . . . . . . . . . . . . . . 1.3 Watts
Small Outline Package (R) . . . . . . . . . . . . . . . . . . 0.9 Watts
Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ±VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . ±3.4 V
Output Short Circuit Duration
. . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves
Storage Temperature Range N, R . . . . . . . . –65°C to +125°C
Operating Temperature Range (A Grade) . . . –40°C to +85°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C
While the AD8041 is internally short circuit protected, this may
not be sufficient to guarantee that the maximum junction tem-
perature (+150°C) is not exceeded under all conditions. To en-
sure proper operation, it is necessary to observe the maximum
power derating curves.
NOTES
1Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2Specification is for the device in free air:
2.0
8-PIN MINI-DIP PACKAGE
T
= +150°C
J
8-Pin Plastic Package: θJA = 90°C/Watt
8-Pin SOIC Package: θJA = 160°C/Watt.
1.5
1.0
0.5
0
ORDERING GUIDE
Temperature
Range
Package
Option
Model
8-PIN SOIC PACKAGE
AD8041AN
AD8041AR
–40°C to +85°C
–40°C to +85°C
8-Pin Plastic DIP
8-Pin Plastic SOIC
REEL-SOIC
AD8041AR-REEL
AD8041-EB
Evaluation Board
–50 –40 –30 –20 –10
0
10 20 30 40 50 60 70 80 90
AMBIENT TEMPERATURE –
°C
Figure 3. Maximum Power Dissipation vs. Temperature
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD8041 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. 0
–5–
AD8041–Typical Performance Characteristics
30
100
95
90
85
80
75
70
V
= ±2.5V
S
T = +25°C
91 PARTS
MEAN = +0.21
STD DEVIATION = 1.47
25
20
15
10
5
V
= +5V
S
T = +25°C
0
–6 –5 –4 –3 –2 –1
0
1
2
3
4
5
6
0
250
500
750
1000 1250
1500
1750
2000
V
– mV
LOAD RESISTANCE – Ω
OS
Figure 4. Typical Distribution of VOS
Figure 7. Open-Loop Gain vs. RL to +25°C
100
97
0.20
0.15
0.10
0.05
0
MEAN = 0.02µV/°C
STD DEV = 2.87µV/°C
SAMPLE SIZE = 45
94
V
= +5V
S
R
= 1kΩ TO +2.5V
L
91
88
85
–10
–7.5
–5
–2.5
V
0
2.5
5
7.5
10
–60 –40 –20
0
20
40
60
80
100 120
DRIFT – µV/°C
TEMPERATURE –
°
C
OS
Figure 8. Open-Loop Gain vs. Temperature
Figure 5. VOS Drift Over –40°C to +85°C
100
2
V = +5V
S
R
= 500Ω TO +2.5V
= 50Ω TO +2.5V
L
V
V
= +5V
= 0V
S
90
80
70
60
50
40
CM
1.5
1
R
L
0.5
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
–45 –35 –25 –15 –5
5
15 25 35 45 55 65 75 85
OUTPUT VOLTAGE – Volts
TEMPERATURE –
°
C
Figure 9. Open-Loop Gain vs. Output Voltage
Figure 6. IB vs. Temperature
REV. 0
–6–
AD8041
200
150
100
50
0
10
100
1k
10k
100k
FREQUENCY – Hz
Figure 10. Input Voltage Noise vs. Frequency
Figure 13. Differential Gain and Phase Errors
6.5
6.4
–30
V
R
= +3V, A = –1,
V
= 100Ω TO 1.5V
S
V
= +5V
S
L
–40
–50
–60
–70
–80
–90
–100
G = +2
R
R
6.3
6.2
6.1
6.0
5.9
5.8
5.7
5.6
5.5
= 150Ω TO 2.5V
= 402Ω
L
F
V
R
= +5V, A = +2,
V
= 100Ω TO 2.5V
S
L
V
R
= +5V, A = +1,
V
= 100Ω TO 2.5V
S
32.4MHz
L
V
= +5V, A = +2,
V
S
R
= 1kΩ TO 2.5V
L
V
= +5V, A = +1,
V
= 1kΩ TO 2.5V
S
R
L
1
10
100
500
1
2
3
4
5
6
7
8 9 10
FREQUENCY – MHz
FUNDAMENTAL FREQUENCY – MHz
Figure 14. 0.1 dB Gain Flatness
Figure 11. Total Harmonic Distortion
–30
–40
+180
+135
90
+120
+100
+80
10MHz
5MHz
V
R
C
= +5V
= 2kΩ TO +2.5V
= 5pF TO +2.5V
–50
S
GAIN
L
L
–60
–70
45
+60
–80
0
1MHz
+40
+20
–90
PHASE
–100
–110
–120
–130
–140
–45
–90
–135
–180
V
= +5V
S
0
R
= 2kΩ TO +2.5V
L
GAIN = +2
–20
–40
2.5
OUTPUT VOLTAGE – V
0
0.5
1
1.5
2
3
3.5
4
4.5
5
0.0
0.1
1
10
100
500
PP
FREQUENCY – MHz
Figure 12. Worst Harmonic vs. Output Voltage
Figure 15. Open-Loop Gain and Phase Margin
vs. Frequency
REV. 0
–7–
AD8041–Typical Performance Characteristics
5
50
40
30
V = +5V
S
4
G = –1
R
= 2kΩ TO 2.5V
T = +125°C
L
C = 5pF
V
= +3V, 0.1%
3
2
L
S
G =+1
T = +25°C
V
= ±5V, 0.1%
1
S
0
T = –55°C
–1
–2
–3
–4
–5
V
= +3V, 1%
S
20
10
V
S
= ±5V, 1%
1
10
FREQUENCY – MHz
100
500
0.5
1
1.5
2
INPUT STEP – Volts p-p
Figure 16. Closed-Loop Frequency Response
vs. Temperature
Figure 19. Settling Time vs. Input Step
–10
5
GAIN = +1
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
4
3
V
R
= +3V
S
R
= 2kΩ
L
V = +3V AND ±5V
S
& C TO 1.5V
L
L
C = 5pF
L
V
R
= +5V
& C TO 2.5V
S
2
L
L
1
0
V
= ±5V
S
–1
–2
–3
–4
–5
1
10
FREQUENCY – MHz
100
500
0.01
0.1
1
10
100
500
FREQUENCY – MHz
Figure 20. CMRR vs. Frequency
Figure 17. Closed-Loop Frequency Response vs. Supply
0.60
0.50
0.40
0.30
0.20
0.10
0
100
V
= +5V
S
GAIN = +1
C
°
V
= +5V
S
+125
OH,
10
1
C
°
–55
+5V – V
OH,
C
°
+5V – V
, +125
OL
V
C
°
, –55
OL
V
0.1
0.01
0.01
0
5
10
15
20
25
30
35
40
45
50
0.1
1
10
100
500
FREQUENCY – MHz
LOAD CURRENT – mA
Figure 18. Output Resistance vs. Frequency
Figure 21. Output Saturation Voltage vs. Load Current
REV. 0
–8–
AD8041
8
7
6
5
4
3
90
80
70
60
50
40
30
20
10
0
100kΩ
V
= +5V
S
1kΩ
R
SERIES
C
LOAD
V
IN
V
= ±5V
S
V
= +5V
S
20
MARGIN
° PHASE
V
= +3V
S
45
MARGIN
° PHASE
2
–60 –40 –20
0
20
40
60
80
100 120
0
10
20
30
40
50
60
TEMPERATURE –
°C
SERIES RESISTANCE – Ω
Figure 22. Supply Current vs. Temperature
Figure 25. Capacitive Load vs. Series Resistance
5
4
40
20
V
R
R
= +5V
= 5KΩ TO +2.5V
= 2kΩ
V
= +5V
S
S
3
2
L
F
0
–20
G = +2
–PSRR
–40
1
–60
0
+PSRR
–80
–1
–2
–3
–4
–5
G = +5
–100
–120
–140
–160
G = +10
G = +2,
R
= 402Ω
L
1M
10M
FREQUENCY – Hz
100M
500M
0.01
0.1
1
10
100
500
FREQUENCY – MHz
Figure 26. Frequency Response vs. Closed-Loop Gain
Figure 23. PSRR vs. Frequency
10
9
8
7
6
5
4
3
2
1
0
1.600V
V
= 0.1V p-p
I
N
1.575V
1.550V
1.525V
1.500V
1.475V
1.450V
1.425V
1.400V
R
V
=
2kΩ
L
= +3V
S
V
R
= ±5V
= 2kΩ
S
G = +1
L
50mV
10ns
0.1
1
10
100
1000
FREQUENCY – MHz
Figure 24. Output Voltage Swing vs. Frequency
Figure 27. Pulse Response, VS = +3 V
REV. 0
–9–
AD8041–Typical Performance Characteristics
5V
4.840V MAX
V
= +5V
2.6V
2.55V
2.5V
S
G = +1
R
V
4V
= 2kΩ
L
R
L
= 150Ω TO +2.5V
= 5pF
L
3V
2V
1V
0V
2.45V
2.4V
0.111V MIN
200µs
50mV
40ns
1V
Figure 28a.
Figure 30. 100 mV Step Response, VS = +5 V, G = +1
5V
4V
3V
2V
1V
0V
3V
4.741V MAX
V
= 3V p-p
IN
f = 0.1MHz
2.5V
2V
R
= 2kΩ
L
R
= 150Ω TO GND
L
V
= +3V
S
G = –1
1.5V
1V
0.5V
0V
0.043V MIN
500mV
1V
2µs
200µs
Figure 28b.
Figure 31. Output Swing, VS = +3 V, VIN = 3 V p-p
Figure 28a-b. Output Swing vs. Load Reference Voltage,
VS = +5 V, G = –1
3V
4.5V
V
= +5V
S
V
= 2.8V p-p
IN
f = 0.8MHz
G = +2
R
V
2.5V
2V
= 2kΩ
R
= 2kΩ
L
L
3.5V
2.5V
1.5V
0.5V
= 1V p-p
V
= +3V
IN
S
G = –1
1.5V
1V
0.5V
0V
500mV
2µs
1V
40ns
Figure 32. Output Swing, VS = +3 V, VIN = 2.8 V p-p
Figure 29. One Volt Step Response, VS = +5 V, G = +2
REV. 0
–10–
AD8041
Overdrive Recovery
capacitor C9. R1 is the output resistance of the input stage; gm
is the input transconductance. C7 and C9 provide Miller com-
pensation for the overall op amp. The unity gain frequency will
occur at gm/C9. Solving the node equations for this circuit
yields:
Overdrive of an amplifier occurs when the output and/or input
range are exceeded. The amplifier must recover from this over-
drive condition. As shown in Figure 33, the AD8041 recovers
within 50 ns from negative overdrive and within 25 ns from
positive overdrive.
VOUT
Vi
A0
=
gm2
C3
5V
(sR1[C9 (A2 +1)] + 1) × s
+1
OUTPUT
INPUT
where A0 = gmgm2 R2 R1 (Open-Loop Gain of Op Amp)
A2 = gm2 R2 (Open-Loop Gain of Output Stage)
2.5V
G = +2
The first pole in the denominator is the dominant pole of the
amplifier, and occurs at about 180 Hz. This equals the input
stage output impedance R1 multiplied by the Miller-multiplied
value of C9. The second pole occurs at the unity-gain band-
width of the output stage, which is 250 MHz. This type of
architecture allows more open-loop gain and output drive to be
obtained than a standard two-stage architecture would allow.
V
= +5V
S
0V
50mV
40ns
Figure 33. Overdrive Recovery
Circuit Description
Output Impedance
The AD8041 is fabricated on Analog Devices’ proprietary
eXtra-Fast Complementary Bipolar (XFCB) process which en-
ables the construction of PNP and NPN transistors with similar
fTs in the 2 GHz–4 GHz region. The process is dielectrically iso-
lated to eliminate the parasitic and latch-up problems caused by
junction isolation. These features allow the construction of high
frequency, low distortion amplifiers with low supply currents.
This design uses a differential output input stage to maximize
bandwidth and headroom (see Figure 34). The smaller signal
swings required on the first stage outputs (nodes S1P, S1N)
reduce the effect of nonlinear currents due to junction
capacitances and improve the distortion performance. With this
design harmonic distortion of better than –85 dB @ 1 MHz into
100 Ω with VOUT = 2 V p-p (Gain = +2) on a single 5 volt sup-
ply is achieved.
The low frequency open-loop output impedance of the common
emitter output stage used in this design is approximately 6.5 kΩ.
While this is significantly higher than a typical emitter follower
output stage, when connected with feedback the output imped-
ance is reduced by the open-loop gain of the op amp. With
110 dB of open-loop gain the output impedance is reduced to
less than 0.1 Ω. At higher frequencies the output impedance will
rise as the open-loop gain of the op amp drops; however, the
output also becomes capacitive due to the integrator capacitors
C9 and C3. This prevents the output impedance from ever
becoming excessively high (see Figure 18), which can cause
stability problems when driving capacitive loads. In fact, the
AD8041 has excellent cap-load drive capability for a high-
frequency op amp. Figure 25 demonstrates that the AD8041
exhibits a 45° margin while driving a 20 pF direct capacitive
load. In addition, running the part at higher gains will also
improve the capacitive load drive capability of the op amp.
The complementary common-emitter design of the output stage
provides excellent load drive without the need for emitter fol-
lowers, thereby improving the output range of the device consid-
erably with respect to conventional op amps. High output drive
capability is provided by injecting all output stage predriver cur-
rents directly into the bases of the output devices Q8 and Q36.
Biasing of Q8 and Q36 is accomplished by I8 and I5, along with
a common-mode feedback loop (not shown). This circuit topol-
ogy allows the AD8041 to drive 50 mA of output current with
the outputs within 0.5 V of the supply rails.
V
CC
I1
I10
I2
I3
I9
Q50
Q39
Q25
R26
Q4
R39
Q5
Q36
I5
Q51
Q23
V
Q40
EE
R15 R2
Q22
R27
R23
V
EE
C3
Q31
Q7
Q17
V
V
P
N
Q13
V
OUT
IN
Q21
Q27
IN
On the input side, the device can handle voltages from –0.2 V
below the negative rail to within 1.2 V of the positive rail. Ex-
ceeding these values will not cause phase reversal; however, the
input ESD devices will begin to conduct if the input voltages ex-
ceed the rails by greater than 0.5 V.
C9
SIN
SIP
Q2
Q11
R3
Q8
IB
Q3
Q24
I7
Q47
V
CC
C7
R5
R21
V
EE
A “Nested Integrator” topology is used in the AD8041 (see
small-signal schematic shown in Figure 35). The output stage
can be modeled as an ideal op amp with a single-pole response
and a unity-gain frequency set by transconductance gm2 and
Figure 34. AD8041 Simplified Schematic
REV. 0
–11–
AD8041
C9
R2
V
= +5V
S
100
90
S1N
C3
g
Vi
R1
m
V
OUT
g
m2
S1P
C7
10
0%
g
Vi
R1
m
1V
200ns
Figure 37. 2:1 Multiplexer Performance
Single Supply A/D Conversion
Figure 35. Small Signal Schematic
Disable Operation
Figure 38 shows the AD8041 driving the analog inputs of the
AD9050 in a dc coupled system with single ended signals. All
components are powered from a single +5 V supply. The
AD820 is used to offset the ground referenced input signal to
the level required by the AD9050. The AD8041 is used to add
in the offset with the ground referenced input signal and buffer
the input to AD9050. The nominal input range of the AD9050
The AD8041 has an active-low disable pin, which can be used
to three-state the output of the part and also lower its supply
current. If the disable pin is left floating, the part is enabled and
will perform normally. If the disable pin is pulled to 2.5 V
(min) below the positive supply, output of the AD8041 will be
disabled and the nominal supply current will drop to less than
1.6 mA. For best isolation, the disable pin should be pulled to
as low a voltage as possible; ideally, the negative supply rail.
1000Ω
+5V
The disable pin on the AD8041 allows it to be configured as
an 2:1 mux as shown in Figure 36 and can be used to switch
many types of high speed signals. Higher order multiplexers can
also be built. The break-before-make switching time is approxi-
mately 50 ns to disable the output and 300 ns to enable the
output.
+5V
1000Ω
V
IN
10
–0.5V TO +0.5V
AD8041
2.8V – 3.8V
3.3V
AD9050
9
0.1µF
+5V
+5V
1000Ω
1000Ω
0.1µF
10µF
AD820
CH0
5MHz
7
3
2
50Ω
AD8041
6
4
G = 2
Figure 38. 10-Bit, 40 MSPS A/D Conversion
8
is +2.8 V and +3.8 V (1 V p-p centered at +3.3 V). This circuit
provides 40 MSPS analog-to-digital conversion on just 330 mW
of power while delivering 10-bit performance.
330Ω
330Ω
50Ω
+5V
0
10µF
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
F
= 4.9MHz
1
FUNDAMENTAL = 0.6dB
2nd HARMONIC = 66.9dB
3rd HARMONIC = 74.7dB
SNR = 55.2dB
NOISE FLOOR = – 86.1dB
ENCODE FREQUENCY = 40MHz
CH1
10MHz
7
3
2
50Ω
AD8041
6
G = 2
4
8
330Ω
330Ω
10
12 11
13
74HC04
Figure 36. 2:1 Multiplexer
Figure 39. FFT Output of Circuit in Figure 38
–12–
REV. 0
AD8041
APPLICATIONS
Single Supply Composite Video Line Driver
RGB Buffer
Figure 42 shows a schematic of a single supply gain-of-two com-
posite video line driver. Since the sync tips of a composite video
signal extend below ground, the input must be ac coupled and
shifted positively to provide signal swing during these negative
excursions in a single supply configuration.
The AD8041 can provide buffering of RGB signals that include
ground while operating from a single +3 V or +5 V supply.
The signals that drive an RGB monitor are usually supplied by
current output DACs that operate from a +5 V only supply.
These can triple DACs like the ADV7120 and ADV7122 from
Analog Devices or integrated into the graphics controller IC as
in most PCs these days.
The input is terminated in 75 Ω and ac coupled via CIN to a
voltage divider that provides the dc bias point to the input. Set-
ting the optimal bias point requires some understanding of the
nature of composite video signals and the video performance of
the AD8041.
During the horizontal blanking interval the currents output from
the DACs go to zero and the RGB signals are pulled to ground
via the termination resistors. If more than one RGB monitor is
desired, it cannot simply be connected in parallel because it will
provide an additional termination. Therefore, buffering must be
provided before connecting a second monitor.
Signals of bounded peak-to-peak amplitude that vary in duty
cycle require larger dynamic swing capability than their peak-to-
peak amplitude after ac coupling. As a worst case, the dynamic
signal swing required will approach twice the peak-to-peak
value. The two bounding cases are for a duty cycle that is mostly
low, but occasionally goes high at a fraction of a percent duty
cycle and vice versa.
Since the RGB signals include ground as part of their dynamic
output range, it has previously been required to use a dual sup-
ply op amp to provide this buffering. In some systems this is the
only component that requires a negative supply so it can be
quite inconvenient to incorporate this multiple monitor feature.
Composite video is not quite this demanding. One bounding ex-
treme is for a signal that is mostly black for an entire frame, but
has a white (full intensity), minimum width spike at least once
per frame.
Figure 40 shows a schematic of one channel of a single supply
gain-of-two buffer for driving a second RGB monitor. No cur-
rent is required when the amplifier output is at ground. The ter-
mination resistor at the monitor helps pull the output down at
low voltage levels.
The other extreme is for a video signal that is full white every-
where. The blanking intervals and sync tips of such a signal will
have negative going excursions in compliance with composite
video specifications. The combination of horizontal and vertical
blanking intervals limit such a signal to being at its highest level
(white) for only about 75% of the time.
+3V OR +5V
0.1µF
10µF
NC
8
As a result of the duty cycle variations between the two extremes
presented above, a 1 V p-p composite video signal that is multi-
plied by a gain of two requires about 3.2 V p-p of dynamic volt-
age swing at the output for an op amp to pass a composite video
signal of arbitrary duty cycle without distortion.
R, G OR B
7
3
2
75Ω
6
AD8041
4
75Ω
1kΩ
75Ω
Some circuits use a sync tip clamp along with ac coupling to
hold the sync tips at a relatively constant level in order to lower
the amount of dynamic signal swing required. However, these
circuits can have artifacts like sync tip compression unless they
are driven by sources with very low output impedance.
SECOND RGB
MONITOR
1kΩ
PRIMARY RGB
MONITOR
Figure 40. Single Supply RGB Buffer
Figure 41 is an oscilloscope photo of the circuit in Figure 40
operating from a +3 V supply and driven by the Blue signal of a
color bar pattern. Note that the input and output are at ground
during the horizontal blanking interval. The RGB signals are
specified to output a maximum of 700 mV peak. The output of
the AD8041 is 1.4 V with the termination resistors providing a
divide-by-two. The Red and Green signals can be buffered in
the same manner with duplication of this circuit.
+5V
4.99kΩ
4.99kΩ
10µF
10µF
0.1µF
6
47µF
7
COMPOSITE
VIDEO IN
75Ω
COAX
3
1000µF
V
OUT
10kΩ
AD8041
4
75Ω
R
75Ω
R
8
T
L
75Ω
2
0.1µF
NC
500mV
5µs
R
R
G
F
1kΩ
1kΩ
100
90
220µF
V
IN
GND
GND
Figure 42. Single Supply Composite Video Line Driver
V
OUT
The AD8041 not only has ample signal swing capability to
handle the dynamic range required without using a sync tip
clamp, but also has good video specifications like differential
gain and differential phase when buffering these signals in an ac
coupled configuration.
10
0%
500mV
Figure 41. +3 V, RGB Buffer
REV. 0
–13–
AD8041
To test this, the differential gain and differential phase were
measured for the AD8041 while the supplies were varied. As the
lower supply is raised to approach the video signal, the first ef-
fect to be observed is that the sync tips become compressed be-
fore the differential gain and differential phase are adversely
affected. Thus, there must be adequate swing in the negative di-
rection to pass the sync tips without compression.
Referring to Figure 44, the Green plus sync signal is output
from an ADV7120, a single supply triple video DAC. Because
the DAC is single supply, the lowest level of the sync tip is at
ground or slightly above. The AD8041 is set for a gain of two to
compensate for the divide by two of the output terminations.
500mV
10µs
As the upper supply is lowered to approach the video, the differ-
ential gain and differential phase were not significantly adversely
affected until the difference between the peak video output and
the supply reached 0.6 V. Thus, the highest video level should
be kept at least 0.6 V below the positive supply rail.
100
90
Taking the above into account, it was found that the optimal
point to bias the noninverting input is at 2.2 V dc. Operating at
this point, the worst case differential gain is measured at 0.06%
and the worst case differential phase is 0.06°.
10
0%
500mV
The ac coupling capacitors used in the circuit at first glance ap-
pear quite large. A composite video signal has a lower frequency
band edge of 30 Hz. The resistances at the various ac coupling
points—especially at the output—are quite small. In order to
minimize phase shifts and baseline tilt, the large value capacitors
are required. For video system performance that is not to be of
the highest quality, the value of these capacitors can be reduced
by a factor of up to five with only a slightly observable change in
the picture quality.
Figure 44. Single Supply Sync Stripper
The reference voltage for R1 should be twice the dc blanking
level of the G signal. If the blanking level is at ground and the
sync tip is negative as in some dual supply systems, then R1 can
be tied to ground. In either case, the output will have the sync
removed and have the blanking level at ground.
Layout Considerations
The specified high speed performance of the AD8041 requires
careful attention to board layout and component selection.
Proper RF design techniques and low-pass parasitic component
selection are necessary.
Sync Stripper
Some RGB monitor systems use only three cables total and
carry the synchronizing signals along with the Green (G) signal
on the same cable. The sync signals are pulses that go in the
negative direction from the blanking level of the G signal.
The PCB should have a ground plane covering all unused por-
tions of the component side of the board to provide a low im-
pedance path. The ground plane should be removed from the
area near the input pins to reduce the stray capacitance.
In some applications like prior to digitizing component video
signals with A/D converters, it is desirable to remove or strip the
sync portion from the G signal. Figure 43 is a schematic of a cir-
cuit using the AD8041 running on a single +5 V supply that
performs this function.
Chip capacitors should be used for the supply bypassing (see
Figure 45). One end should be connected to the ground plane
and the other within 1/8 inch of each power pin. An additional
large (0.47 µF–10 µF) tantalum electrolytic capacitor should be
connected in parallel, but not necessarily so close, to supply cur-
rent for fast, large signal changes at the output.
GREEN W/SYNC
GREEN W/OUT SYNC
+5V
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to a
minimum. Capacitance variations of less than 1 pF at the in-
verting input will significantly affect high speed performance.
V
+0.4
GROUND
10µF
BLANK
0.1µF
GROUND
7
AD8041
4
3
2
V
IN
Stripline design techniques should be used for long signal traces
(greater than about 1 inch). These should be designed with a
characteristic impedance of 50 Ω or 75 Ω and be properly termi-
nated at each end.
75Ω
6
75Ω
75Ω
(MONITOR)
R2
1kΩ
R1
1kΩ
0.8V
(2X V
)
BLANK
Figure 43. Single Supply Sync Stripper
–14–
REV. 0
AD8041
Table I. Recommended Component Values
Evaluation Board
An evaluation board for the AD8041 is available which has been
carefully laid out and tested to demonstrate that the specified
high speed performance of the device can be realized. For
ordering information, please refer to the ordering guide.
AD8041A
Gain
Component
+1
+2
+2
+5
+10
RF
RG
0 Ω
2 kΩ 400 Ω 2 kΩ 2 kΩ
2 kΩ 400 Ω 500 Ω 220 Ω
The layout of the evaluation board can be used as shown or
serve as a guide for a board layout.
RO (Nominal)
RT (Nominal)
Small Signal BW (MHz)
VS = +5 V
0.1 dB Bandwidth (MHz)
VS = +5 V
75 Ω 75 Ω 75 Ω 75 Ω 75 Ω
75 Ω 75 Ω 75 Ω 75 Ω 75 Ω
160
67
7
72
32
20
9
Figure 45. Noninverting Configurations for Evaluation
Boards
Figure 47. Board Layout (Component Side)
Figure 48. Board Layout (Back Side)
Figure 46. Evaluation Board Silkscreen (Top)
REV. 0
–15–
AD8041
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead Plastic DIP
(N-8)
8
5
0.25
(6.35)
0.31
(7.87)
PIN 1
1
4
0.30 (7.62)
REF
0.39 (9.91) MAX
0.035±0.01
(0.89±0.25)
0.165±0.01
(4.19±0.25)
0.011±0.003
(0.28±0.08)
0.18±0.03
(4.57±0.76)
0.125
(3.18)
MIN
15
°
0°
0.10
(2.54)
0.018±0.003
(0.46±0.08)
0.033
(0.84)
NOM
SEATING
PLANE
BSC
8-Lead Plastic SOIC
(SO-8)
8
5
0.1574 (4.00)
0.1497 (3.80)
PIN 1
0.2440 (6.20)
0.2284 (5.80)
4
1
0.1968 (5.00)
0.1890 (4.80)
0.0196 (0.50)
0.0099 (0.25)
x 45°
0.0688 (1.75)
0.0532 (1.35)
0.0098 (0.25)
0.0040 (0.10)
8
0
°
°
0.0500 (1.27)
0.0160 (0.41)
0.0192 (0.49)
0.0138 (0.35)
0.0500
(1.27)
BSC
0.0098 (0.25)
0.0075 (0.19)
–16–
REV. 0
相关型号:
AD8041ARZ
MICROCIRCUIT, LINEAR, 160 MHz, RAIL-TO-RAIL AMPLIFIER WITH DISABLE, MONOLITHIC SILICON
ETC
©2020 ICPDF网 联系我们和版权申明