AD7918BRUZ-REEL7 [ADI]
8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs; 8通道, 1 MSPS , 8位/ 10位/ 12位ADC型号: | AD7918BRUZ-REEL7 |
厂家: | ADI |
描述: | 8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs |
文件: | 总32页 (文件大小:456K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs
with Sequencer in 20-Lead TSSOP
AD7908/AD7918/AD7928
FUNCTIONAL BLOCK DIAGRAM
FEATURES
AV
DD
Fast throughput rate: 1 MSPS
Specified for AVDD of 2.7 V to 5.25 V
Low power
6.0 mW max at 1 MSPS with 3 V supply
13.5 mW max at 1 MSPS with 5 V supply
Eight (single-ended) inputs with sequencer
Wide input bandwidth
AD7928, 70 dB min SINAD at 50 kHz input frequency
Flexible power/serial clock speed management
No pipeline delays
REF
V
IN
0
IN
T/H
•
•
•
•
•
•
•
•
•
•
•
•
•
8-/10-/12-BIT
SUCCESSIVE
APPROXIMATION
ADC
I/P
MUX
High speed serial interface SPI®/QSPI™/
MICROWIRE™/DSP compatible
Shutdown mode: 0.5 μA max
V
7
IN
SCLK
DOUT
DIN
CONTROL LOGIC
SEQUENCER
20-lead TSSOP package
CS
Qualified for automotive applications
AD7908/AD7918/AD7928
V
DRIVE
GENERAL DESCRIPTION
GND
The AD7908/AD7918/AD7928 are, respectively, 8-bit, 10-bit, and
12-bit, high speed, low power, 8-channel, successive approximation
ADCs. The parts operate from a single 2.7 V to 5.25 V power
supply and feature throughput rates up to 1 MSPS. The parts
contain a low noise, wide bandwidth track-and-hold amplifier that
can handle input frequencies in excess of 8 MHz.
Figure 1.
PRODUCT HIGHLIGHTS
1. High Throughput with Low Power Consumption. The AD7908/
AD7918/AD7928 offer up to 1 MSPS throughput rates. At the
maximum throughput rate with 3 V supplies, the AD7908/
AD7918/AD7928 dissipate just 6 mW of power maximum.
The conversion process and data acquisition are controlled using
CS
and the serial clock signal, allowing the device to easily interface
with microprocessors or DSPs. The input signal is sampled on the
CS
2. Eight Single-Ended Inputs with a Channel Sequencer.
A sequence of channels can be selected, through which
the ADC cycles and converts on.
falling edge of
and conversion is also initiated at this point.
There are no pipeline delays associated with the part.
3. Single-Supply Operation with VDRIVE Function. The AD7908/
AD7918/AD7928 operate from a single 2.7 V to 5.25 V supply.
The VDRIVE function allows the serial interface to connect directly
The AD7908/AD7918/AD7928 use advanced design techniques to
achieve very low power dissipation at maximum throughput rates.
At maximum throughput rates, the AD7908/AD7918/AD7928
consume 2 mA maximum with 3 V supplies; with 5 V supplies, the
current consumption is 2.7 mA maximum.
to either 3 V or 5 V processor systems independent of AVDD
.
4. Flexible Power/Serial Clock Speed Management. The conversion
rate is determined by the serial clock, allowing the conversion
time to be reduced through the serial clock speed increase. The
parts also feature various shutdown modes to maximize power
efficiency at lower throughput rates. Current consumption is
0.5 μA max when in full shutdown.
Through the configuration of the control register, the analog input
range for the part can be selected as 0 V to REFIN or 0 V to 2 ×
REFIN, with either straight binary or twos complement output
coding. The AD7908/AD7918/AD7928 each feature eight single-
ended analog inputs with a channel sequencer to allow a
5. No Pipeline Delay. The parts feature a standard successive
approximation ADC with accurate control of the sampling
preprogrammed selection of channels to be converted sequentially.
The conversion time for the AD7908/AD7918/AD7928 is
determined by the SCLK frequency, which is also used as the
master clock to control the conversion.
CS
instant via a input and once off conversion control.
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2006–2010 Analog Devices, Inc. All rights reserved.
AD7908/AD7918/AD7928
TABLE OF CONTENTS
Features .............................................................................................. 1
Control Register.............................................................................. 15
Sequencer Operation ................................................................. 16
SHADOW Register .................................................................... 17
Circuit Information.................................................................... 18
Converter Operation.................................................................. 18
ADC Transfer Function............................................................. 19
Handling Bipolar Input Signals................................................ 19
Typical Connection Diagram ................................................... 19
Modes of Operation................................................................... 21
Power vs. Throughput Rate....................................................... 23
Serial Interface............................................................................ 23
Microprocessor Interfacing....................................................... 24
Application Hints ....................................................................... 27
Outline Dimensions....................................................................... 28
Ordering Guide .......................................................................... 29
Automotive Products................................................................. 29
General Description......................................................................... 1
Functional Block Diagram .............................................................. 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
AD7908 Specifications................................................................. 3
AD7918 Specifications................................................................. 5
AD7928 Specifications................................................................. 7
Timing Specifications .................................................................. 9
Absolute Maximum Ratings.......................................................... 10
ESD Caution................................................................................ 10
Pin Configuration and Function Descriptions........................... 11
Terminology .................................................................................... 12
Typical Performance Characteristics ........................................... 13
Performance Curves................................................................... 13
REVISION HISTORY
12/10—Rev. C to Rev. D
6/06—Rev. A to Rev. B
Changes to Features Section............................................................ 1
Added Automotive SINAD and SNR Parameters (Table 1)........ 3
Added Automotive SINAD and SNR Parameters (Table 2)........ 5
Added Automotive SINAD and SNR Parameters (Table 3)........ 7
Added Automotive Temperature Range (Table 5) ....................... 7
Added Automotive Products Section .......................................... 28
Changes to Ordering Guide .......................................................... 28
Updated Format..................................................................Universal
Changes to Reference Section....................................................... 21
9/03—Rev. 0 to Rev. A
Changes to Figure 3........................................................................ 15
Changes to Reference section ....................................................... 18
11/08—Rev. B to Rev. C
Changes to ESD Parameter, Table 5 ............................................. 10
Rev. D | Page 2 of 32
AD7908/AD7918/AD7928
SPECIFICATIONS
AD7908 SPECIFICATIONS
AVDD = VDRIVE = 2.7 V to 5.25 V, REFIN = 2.5 V, fSCLK = 20 MHz, TA = TMIN to TMAX, unless otherwise noted.
Table 1.
Parameter
B Version1
Unit
Test Conditions/Comments
fIN = 50 kHz sine wave, fSCLK = 20 MHz
B models
W models
B models
DYNAMIC PERFORMANCE
Signal-to-(Noise + Distortion) (SINAD)2
49
dB min
dB min
dB min
dB min
dB max
dB max
48.5
49
Signal-to-Noise Ratio (SNR)2
48.5
−66
−64
W models
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise (SFDR)2
Intermodulation Distortion (IMD)2
Second-Order Terms
Third-Order Terms
Aperture Delay
fa = 40.1 kHz, fb = 41.5 kHz
−90
−90
10
dB typ
dB typ
ns typ
Aperture Jitter
50
ps typ
Channel-to-Channel Isolation2
−85
8.2
1.6
dB typ
MHz typ
MHz typ
fIN = 400 kHz
@ 3 dB
Full Power Bandwidth
@ 0.1 dB
DC ACCURACY2
Resolution
8
Bits
Integral Nonlinearity
Differential Nonlinearity
0 V to REFIN Input Range
Offset Error
Offset Error Match
Gain Error
0.2
0.2
LSB max
LSB max
Guaranteed no missed codes to 8 bits
Straight binary output coding
0.5
0.05
0.2
LSB max
LSB max
LSB max
LSB max
Gain Error Match
0 V to 2 × REFIN Input Range
0.05
−REFIN to +REFIN biased about REFIN with
twos complement output coding
Positive Gain Error
Positive Gain Error Match
Zero Code Error
0.2
0.05
0.5
0.1
0.2
LSB max
LSB max
LSB max
LSB max
LSB max
LSB max
Zero Code Error Match
Negative Gain Error
Negative Gain Error Match
ANALOG INPUT
0.05
Input Voltage Ranges
0 to REFIN
0 to 2 × REFIN
V
V
RANGE bit set to 1
RANGE bit set to 0, AVDD/VDRIVE = 4.75 V to
5.25 V
DC Leakage Current
Input Capacitance
REFERENCE INPUT
REFIN Input Voltage
DC Leakage Current
REFIN Input Impedance
LOGIC INPUTS
1
20
μA max
pF typ
2.5
1
36
V
1ꢀ specified performance
fSAMPLE = 1 MSPS
μA max
kΩ typ
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
0.7 × VDRIVE
0.3 × VDRIVE
1
10
V min
V max
μA max
pF max
Typically 10 nA, VIN = 0 V or VDRIVE
3
Input Capacitance, CIN
Rev. D | Page 3 of 32
AD7908/AD7918/AD7928
Parameter
B Version1
Unit
Test Conditions/Comments
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance3
Output Coding
VDRIVE − 0.2
0.4
1
V min
ISOURCE = 200 μA, AVDD = 2.7 V to 5.25 V
ISINK = 200 μA
V max
μA max
pF max
10
Straight (natural) binary
Twos complement
Coding bit set to 1
Coding bit set to 0
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
800
300
300
1
ns max
ns max
ns max
16 SCLK cycles with SCLK at 20 MHz
Sine wave input
Full-scale step input
Throughput Rate
POWER REQUIREMENTS
AVDD
MSPS max
See Serial Interface section
2.7/5.25
2.7/5.25
V min/max
V min/max
VDRIVE
4
IDD
Digital inputs = 0 V or VDRIVE
AVDD = 2.7 V to 5.25 V, SCLK On or Off
AVDD = 4.75 V to 5.25 V, fSCLK = 20 MHz
AVDD = 2.7 V to 3.6 V, fSCLK = 20 MHz
fSAMPLE = 250 kSPS
Normal Mode (Static)
Normal Mode (Operational)
600
2.7
2
960
0.5
0.5
μA typ
mA max
mA max
μA typ
μA max
μA max
Using Auto Shutdown Mode
(Static)
SCLK on or off (20 nA typ)
Full Shutdown Mode
Power Dissipation4
Normal Mode (Operational)
13.5
6
2.5
1.5
2.5
1.5
mW max
mW max
μW max
μW max
μW max
μW max
AVDD = 5 V, fSCLK = 20 MHz
AVDD = 3 V, fSCLK = 20 MHz
AVDD = 5 V
AVDD = 3 V
AVDD = 5 V
Auto Shutdown Mode (Static)
Full Shutdown Mode
AVDD = 3 V
1 Temperature ranges as follows: B version: −40°C to +85°C.
2 See Terminology section.
3 Sample tested @ 25°C to ensure compliance.
4 See Power vs. Throughput Rate section.
Rev. D | Page 4 of 32
AD7908/AD7918/AD7928
AD7918 SPECIFICATIONS
AVDD = VDRIVE = 2.7 V to 5.25 V, REFIN = 2.5 V, fSCLK = 20 MHz, TA = TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter
B Version1
Unit
Test Conditions/Comments
fIN = 50 kHz sine wave, fSCLK = 20 MHz
B models
W models
B models
DYNAMIC PERFORMANCE
Signal-to-(Noise + Distortion) (SINAD)2
61
dB min
dB min
dB min
dB min
dB max
dB max
60.5
61
Signal-to-Noise Ratio (SNR)2
60.5
−72
−74
W models
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise (SFDR)2
Intermodulation Distortion (IMD)2
Second-Order Terms
Third-Order Terms
Aperture Delay
fa = 40.1 kHz, fb = 41.5 kHz
−90
−90
10
dB typ
dB typ
ns typ
Aperture Jitter
50
ps typ
Channel-to-Channel Isolation2
−85
8.2
1.6
dB typ
MHz typ
MHz typ
fIN = 400 kHz
@ 3 dB
Full Power Bandwidth
@ 0.1 dB
DC ACCURACY2
Resolution
10
Bits
Integral Nonlinearity
Differential Nonlinearity
0 V to REFIN Input Range
Offset Error
Offset Error Match
Gain Error
0.5
0.5
LSB max
LSB max
Guaranteed no missed codes to 10 bits
Straight binary output coding
2
LSB max
LSB max
LSB max
LSB max
0.2
0.5
0.2
Gain Error Match
0 V to 2 × REFIN Input Range
−REFIN to +REFIN biased about REFIN with twos
complement output coding
Positive Gain Error
Positive Gain Error Match
Zero Code Error
0.5
0.2
2
0.2
0.5
0.2
LSB max
LSB max
LSB max
LSB max
LSB max
LSB max
Zero Code Error Match
Negative Gain Error
Negative Gain Error Match
ANALOG INPUT
Input Voltage Ranges
0 to REFIN
V
RANGE bit set to 1
0 to 2 × REFIN
V
RANGE bit set to 0, AVDD/VDRIVE = 4.75 V to 5.25 V
DC Leakage Current
Input Capacitance
REFERENCE INPUT
REFIN Input Voltage
DC Leakage Current
REFIN Input Impedance
LOGIC INPUTS
1
20
μA max
pF typ
2.5
1
36
V
1ꢀ specified performance
fSAMPLE = 1 MSPS
μA max
kΩ typ
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
0.7 × VDRIVE
0.3 × VDRIVE
1
10
V min
V max
μA max
pF max
Typically 10 nA, VIN = 0 V or VDRIVE
3
Input Capacitance, CIN
Rev. D | Page 5 of 32
AD7908/AD7918/AD7928
Parameter
B Version1
Unit
Test Conditions/Comments
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance3
Output Coding
VDRIVE − 0.2
0.4
1
V min
ISOURCE = 200 μA, AVDD = 2.7 V to 5.25 V
ISINK = 200 μA
V max
μA max
pF max
10
Straight (natural) binary
Twos complement
Coding bit set to 1
Coding bit set to 0
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
800
300
300
1
ns max
ns max
ns max
MSPS max
16 SCLK cycles with SCLK at 20 MHz
Sine wave input
Full-scale step input
Throughput Rate
POWER REQUIREMENTS
AVDD
See Serial Interface section
2.7/5.25
2.7/5.25
V min/max
V min/max
VDRIVE
4
IDD
Digital inputs = 0 V or VDRIVE
AVDD = 2.7 V to 5.25 V, SCLK on or off
AVDD = 4.75 V to 5.25 V, fSCLK = 20 MHz
AVDD = 2.7 V to 3.6 V, fSCLK = 20 MHz
fSAMPLE = 250 kSPS
Normal Mode (Static)
Normal Mode (Operational)
600
2.7
2
960
0.5
0.5
μA typ
mA max
mA max
μA typ
μA max
μA max
Using Auto Shutdown Mode
(Static)
SCLK on or off (20 nA typ)
Full Shutdown Mode
Power Dissipation4
Normal Mode (Operational)
13.5
6
2.5
1.5
2.5
1.5
mW max
mW max
μW max
μW max
μW max
μW max
AVDD = 5 V, fSCLK = 20 MHz
AVDD = 3 V, fSCLK = 20 MHz
AVDD = 5 V
AVDD = 3 V
AVDD = 5 V
Auto Shutdown Mode (Static)
Full Shutdown Mode
AVDD = 3 V
1 Temperature ranges as follows: B version: –40°C to +85°C.
2 See Terminology section.
3 Sample tested @ 25°C to ensure compliance.
4 See Power vs. Throughput Rate section.
Rev. D | Page 6 of 32
AD7908/AD7918/AD7928
AD7928 SPECIFICATIONS
AVDD = VDRIVE = 2.7 V to 5.25 V, REFIN = 2.5 V, fSCLK = 20 MHz, TA = TMIN to TMAX, unless otherwise noted.
Table 3.
Parameter
B Version1
Unit
Test Conditions/Comments
fIN = 50 kHz sine wave, fSCLK = 20 MHz
@ 5 V, B models
@ 5 V, W models
@ 3 V typically 70 dB
B models
DYNAMIC PERFORMANCE
Signal-to-(Noise + Distortion) (SINAD)2
70
dB min
dB min
dB min
dB min
dB min
dB max
dB max
dB max
dB max
69.5
69
70
Signal-to-Noise Ratio (SNR)2
69.5
−77
−73
−78
−76
W models
Total Harmonic Distortion (THD)2
@ 5 V typically −84 dB
@ 3 V typically −77 dB
@ 5 V typically −86 dB
@ 3 V typically −80 dB
fa = 40.1 kHz, fb = 41.5 kHz
Peak Harmonic or Spurious Noise
(SFDR)2
Intermodulation Distortion (IMD)2
Second-Order Terms
Third-Order Terms
−90
−90
10
dB typ
dB typ
ns typ
Aperture Delay
Aperture Jitter
50
ps typ
Channel-to-Channel Isolation2
−85
8.2
1.6
dB typ
MHz typ
MHz typ
fIN = 400 kHz
@ 3 dB
Full Power Bandwidth
@ 0.1 dB
DC ACCURACY2
Resolution
12
Bits
Integral Nonlinearity
Differential Nonlinearity
0 V to REFIN Input Range
Offset Error
Offset Error Match
Gain Error
1
LSB max
LSB max
−0.9/+1.5
Guaranteed no missed codes to 12 bits
Straight binary output coding
Typically 0.5 LSB
8
LSB max
LSB max
LSB max
LSB max
0.5
1.5
0.5
Gain Error Match
0 V to 2 × REFIN Input Range
−REFIN to +REFIN biased about REFIN with twos
complement output coding
Positive Gain Error
Positive Gain Error Match
Zero Code Error
1.5
0.5
8
0.5
1
LSB max
LSB max
LSB max
LSB max
LSB max
LSB max
Typically 0.8 LSB
Zero Code Error Match
Negative Gain Error
Negative Gain Error Match
ANALOG INPUT
0.5
Input Voltage Ranges
0 to REFIN
V
RANGE bit set to 1
0 to 2 × REFIN
V
RANGE bit set to 0, AVDD/VDRIVE = 4.75 V to 5.25 V
DC Leakage Current
Input Capacitance
REFERENCE INPUT
REFIN Input Voltage
DC Leakage Current
REFIN Input Impedance
LOGIC INPUTS
1
20
μA max
pF typ
2.5
1
36
V
1ꢀ specified performance
fSAMPLE = 1 MSPS
μA max
kΩ typ
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
0.7 × VDRIVE
0.3 × VDRIVE
1
10
V min
V max
μA max
pF max
Typically 10 nA, VIN = 0 V or VDRIVE
3
Input Capacitance, CIN
Rev. D | Page 7 of 32
AD7908/AD7918/AD7928
Parameter
B Version1
Unit
Test Conditions/Comments
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance3
Output Coding
VDRIVE − 0.2
0.4
1
V min
ISOURCE = 200 μA, AVDD = 2.7 V to 5.25 V
ISINK = 200 μA
V max
μA max
pF max
10
Straight (natural) binary
Twos complement
Coding bit set to 1
Coding bit set to 0
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
800
300
300
1
ns max
ns max
ns max
MSPS max
16 SCLK cycles with SCLK at 20 MHz
Sine wave input
Full-scale step input
Throughput Rate
POWER REQUIREMENTS
AVDD
See Serial Interface section
2.7/5.25
2.7/5.25
V min/max
V min/max
VDRIVE
4
IDD
Digital inputs = 0 V or VDRIVE
AVDD = 2.7 V to 5.25 V, SCLK on or off
AVDD = 4.75 V to 5.25 V, fSCLK = 20 MHz
AVDD = 2.7 V to 3.6 V, fSCLK = 20 MHz
fSAMPLE = 250 kSPS
Normal Mode (Static)
Normal Mode (Operational)
600
2.7
2
960
0.5
0.5
μA typ
mA max
mA max
μA typ
μA max
μA max
Using Auto Shutdown Mode
(Static)
SCLK on or off (20 nA typ)
Full Shutdown Mode
Power Dissipation4
Normal Mode (Operational)
13.5
6
2.5
1.5
2.5
1.5
mW max
mW max
μW max
μW max
μW max
μW max
AVDD = 5 V, fSCLK = 20 MHz
AVDD = 3 V, fSCLK = 20 MHz
AVDD = 5 V
AVDD = 3 V
AVDD = 5 V
Auto Shutdown Mode (Static)
Full Shutdown Mode
AVDD = 3 V
1 Temperature ranges as follows: B Version: −40°C to +85°C.
2 See Terminology section.
3 Sample tested @ 25°C to ensure compliance.
4 See Power vs. Throughput Rate section.
Rev. D | Page 8 of 32
AD7908/AD7918/AD7928
TIMING SPECIFICATIONS
AVDD = 2.7 V to 5.25 V, VDRIVE ≤ AVDD, REFIN = 2.5 V, TA = TMIN to TMAX, unless otherwise noted.1
Table 4.
Limit at TMIN, TMAX AD7908/AD7918/AD7928
Parameter
AVDD = 3 V
AVDD = 5 V
Unit
Description
2
fSCLK
10
20
10
20
kHz min
MHz max
tCONVERT
tQUIET
16 × tSCLK
50
16 × tSCLK
50
ns min
Minimum quiet time required between CS rising edge and start of
next conversion
CS to SCLK setup time
10
10
ns min
ns max
ns max
ns min
ns min
ns min
ns min/max
ns min
ns min
ns min
μs max
t2
3
t3
Delay from CS until DOUT three-state disabled
Data access time after SCLK falling edge
SCLK low pulse width
SCLK high pulse width
SCLK to DOUT valid hold time
SCLK falling edge to DOUT high impedance
DIN setup time prior to SCLK falling edge
DIN hold time after SCLK falling edge
16th SCLK falling edge to CS high
35
30
3
t4
40
0.4 × tSCLK
0.4 × tSCLK
10
15/45
10
5
20
1
40
0.4 × tSCLK
0.4 × tSCLK
10
15/35
10
5
20
1
t5
t6
t7
t8
t9
t10
t11
t12
4
Power-up time from full power-down/auto shutdown mode
1 Sample tested at 25°C to ensure compliance. All input signals are specified with tr = tf = 5 ns (10ꢀ to 90ꢀ of AVDD) and timed from a voltage level of 1.6 V. See Figure 2.
The 3 V operating range spans from 2.7 V to 3.6 V. The 5 V operating range spans from 4.75 V to 5.25 V.
2 Mark/space ratio for the SCLK input is 40/60 to 60/40.
3 Measured with the load circuit of Figure 2 and defined as the time required for the output to cross 0.4 V or 0.7 × VDRIVE
.
4 t8 is derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 2. The measured number is then extrapolated
back to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t8, quoted in the timing characteristics is the true bus relinquish
time of the part and is independent of the bus loading.
I
200µA
OL
TO
OUTPUT
PIN
1.6V
C
L
50pF
I
200µA
OH
Figure 2. Load Circuit for Digital Output Timing Specifications
Rev. D | Page 9 of 32
AD7908/AD7918/AD7928
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 5.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Parameter
Rating
AVDD to AGND
−0.3 V to +7 V
VDRIVE to AGND
−0.3 V to AVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to +7 V
−0.3 V to AVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
10 mA
Analog Input Voltage to AGND
Digital Input Voltage to AGND
Digital Output Voltage to AGND
REFIN to AGND
Input Current to Any Pin Except
Supplies1
Operating Temperature Range
Commercial (B Version)
Storage Temperature Range
Automotive Temperature Range
Junction Temperature
TSSOP Package, Power Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
−40°C to +85°C
−65°C to +150°C
−40°C to +125°C
150°C
450 mW
143°C/W (TSSOP)
45°C/W (TSSOP)
215°C
220°C
1.5 kV
Infrared (15 sec)
ESD
1 Transient currents of up to 100 mA do not cause SCR latch-up.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. D | Page 10 of 32
AD7908/AD7918/AD7928
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
SCLK
DIN
1
2
20
19
18
17
16
15
14
13
12
11
AGND
V
DRIVE
3
CS
DOUT
AGND
AD7908/
AD7918/
AD7928
AGND
4
AV
DD
5
V
V
V
V
V
V
0
1
2
3
4
5
IN
IN
IN
IN
IN
IN
AV
DD
6
TOP VIEW
(Not to Scale)
REF
IN
7
8
AGND
V
V
7
9
IN
IN
10
6
Figure 3. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
Mnemonic
Description
1
SCLK
Serial Clock. Logic input. SCLK provides the serial clock for accessing data from the part. This clock input is also
used as the clock source for the conversion process of the AD7908/AD7918/AD7928.
2
DIN
Data In. Logic input. Data to be written to the control register of the AD7908/AD7918/AD7928 is provided on
this input and is clocked into the register on the falling edge of SCLK (see the Control Register section).
3
CS
Chip Select. Active low logic input. This input provides the dual function of initiating conversions on the
AD7908/AD7918/AD7928, and also frames the serial data transfer.
4, 8, 17, 20
AGND
Analog Ground. This is the ground reference point for all analog circuitry on the AD7908/AD7918/AD7928. All
analog input signals and any external reference signal should be referred to this AGND voltage. All AGND pins
should be connected together.
5, 6
AVDD
Analog Power Supply Input. The AVDD range for the AD7908/AD7918/AD7928 is from 2.7 V to 5.25 V. For the 0 V
to 2 × REFIN range, AVDD should be from 4.75 V to 5.25 V.
7
REFIN
Reference Input for the AD7908/AD7918/AD7928. An external reference must be applied to this input. The
voltage range for the external reference is 2.5 V 1ꢀ for specified performance.
16 to 9
VIN0 to VIN7
Analog Input 0 through Analog Input 7. These are eight single-ended analog input channels that are
multiplexed into the on-chip track-and-hold. The analog input channel to be converted is selected by using
Address Bit ADD2 through Address Bit ADD0 of the control register. The address bits, in conjunction with the
SEQ and SHADOW bits, allow the sequencer to be programmed. The input range for all input channels can
extend from 0 V to REFIN or 0 V to 2 × REFIN as selected via the RANGE bit in the control register. Any unused
input channels must be connected to AGND to avoid noise pickup.
18
DOUT
Data Out. Logic output. The conversion result from the AD7908/AD7918/AD7928 is provided on this output as
a serial data stream. The bits are clocked out on the falling edge of the SCLK input. The data stream from the
AD7908 consists of one leading zero, three address bits indicating which channel the conversion result
corresponds to, followed by the eight bits of conversion data, followed by four trailing zeros, provided MSB
first; the data stream from the AD7918 consists of one leading zero, three address bits indicating which
channel the conversion result corresponds to, followed by the 10 bits of conversion data, followed by two
trailing zeros, also provided MSB first; the data stream from the AD7928 consists of one leading zero, three
address bits indicating which channel the conversion result corresponds to, followed by the 12 bits of
conversion data, provided MSB first. The output coding can be selected as straight binary or twos complement
via the CODING bit in the control register.
19
VDRIVE
Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the serial interface of
the AD7908/AD7918/AD7928 operates.
Rev. D | Page 11 of 32
AD7908/AD7918/AD7928
TERMINOLOGY
Integral Nonlinearity
Negative Gain Error Match
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale, a position 1 LSB
below the first code transition, and full scale, a position 1 LSB
above the last code transition.
This is the difference in negative gain error between any two
channels.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of
crosstalk between channels. It is measured by applying a full-
scale 400 kHz sine wave signal to all seven nonselected input
channels and determining how much that signal is attenuated
in the selected channel with a 50 kHz signal. The figure is given
worst case across all eight channels for the AD7908/AD7918/
AD7928.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
This is the deviation of the first code transition (00 . . . 000) to
(00 . . . 001) from the ideal, that is, AGND + 1 LSB.
Power Supply Rejection (PSR)
Variations in power supply affect the full-scale transition, but
not the converter’s linearity. Power supply rejection is the
maximum change in full-scale transition point due to a change
in power-supply voltage from the nominal value (see the
Performance Curves section).
Offset Error Match
This is the difference in offset error between any two channels.
Gain Error
This is the deviation of the last code transition (111 . . . 110) to
(111 . . . 111) from the ideal (that is, REFIN – 1 LSB) after the
offset error has been adjusted out.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within 1 LSB, after the end of conversion.
Gain Error Match
This is the difference in gain error between any two channels.
Zero Code Error
Signal-to-(Noise + Distortion) Ratio
This applies when using the twos complement output coding
option, in particular to the 2 × REFIN input range with −REFIN
to +REFIN biased about the REFIN point. It is the deviation of the
midscale transition (all 0s to all 1s) from the ideal VIN voltage,
that is, REFIN − 1 LSB.
This is the measured ratio of signal-to-(noise + distortion) at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the
digitization process; the more levels, the smaller the
quantization noise. The theoretical signal-to-(noise +
distortion) ratio for an ideal N-bit converter with a sine wave
input is given by
Zero Code Error Match
This is the difference in zero code error between any two
channels.
Positive Gain Error
Signal-to-(Noise + Distortion) = (6.02N + 1.76)dB
This applies when using the twos complement output coding
option, in particular to the 2 × REFIN input range with −REFIN
to +REFIN biased about the REFIN point. It is the deviation of the
last code transition (011. . .110) to (011 . . . 111) from the ideal
(that is, +REFIN − 1 LSB) after the zero code error has been
adjusted out.
Thus for a 12-bit converter, this is 74 dB; for a 10-bit converter,
this is 62 dB; and for an 8-bit converter, this is 50 dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7908/AD7918/
AD7928, it is defined as:
Positive Gain Error Match
This is the difference in positive gain error between any two
channels.
2
2
2
2
2
V
+V +V + V +V
2
3
4
5
6
THD
(
dB = 20log
)
Negative Gain Error
V
1
This applies when using the twos complement output coding
option, in particular to the 2 × REFIN input range with −REFIN
to +REFIN biased about the REFIN point. It is the deviation of the
first code transition (100 . . . 000) to (100 . . . 001) from the ideal
(that is, −REFIN + 1 LSB) after the zero code error has been
adjusted out.
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Rev. D | Page 12 of 32
AD7908/AD7918/AD7928
TYPICAL PERFORMANCE CHARACTERISTICS
Figure 7 shows a graph of total harmonic distortion vs. analog
input frequency for various supply voltages, and Figure 8 shows a
graph of total harmonic distortion vs. analog input frequency
for various source impedances. See the Analog Input section.
PERFORMANCE CURVES
Figure 4 shows a typical FFT plot for the AD7928 at 1 MSPS
sample rate and 50 kHz input frequency. Figure 5 shows the
signal-to-(noise + distortion) ratio performance vs. input
frequency for various supply voltages while sampling at 1 MSPS
with an SCLK of 20 MHz.
Figure 9 and Figure 10 show typical INL and DNL plots for the
AD7928.
Figure 6 shows the power supply rejection ratio vs. supply ripple
frequency for the AD7928 when no decoupling is used. The
power supply rejection ratio is defined as the ratio of the power
in the ADC output at full-scale frequency f, to the power of a
200 mV p-p sine wave applied to the ADC AVDD supply of
frequency fS
0
AV
= 5V
DD
200mV p-p SINEWAVE ON AV
–10
–20
–30
–40
–50
–60
–70
–80
–90
DD
REF = 2.5V, 1µF CAPACITOR
IN
= 25°C
T
A
PSRR(dB) = 10 log(Pf/Pfs)
Pf is equal to the power at frequency f in ADC output; PfS is
equal to the power at frequency fS coupled onto the ADC AVDD
supply. Here a 200 mV p-p sine wave is coupled onto the AVDD
supply.
0
100 200 300 400 500 600 700 800 900 1000
SUPPLY RIPPLE FREQUENCY (kHz)
4096 POINT FFT
AV = 5V
–10
DD
fSAMPLE = 1MSPS
fIN = 50kHz
Figure 6. AD7928 PSRR vs. Supply Ripple Frequency
–30
SINAD = 71.147dB
THD = –87.229dB
SFDR = –90.744dB
–50
–55
–60
–65
–70
–75
–80
–85
–90
fSAMPLE = 1MSPS
T
= 25°C
A
RANGE = 0V TO REF
–50
–70
IN
AV
= V = 2.70V
DRIVE
DD
AV
= V
DRIVE
= 3.60V
= 4.75V
DD
–90
–110
0
50
100 150 200 250 300 350 400 450 500
FREQUENCY (kHz)
AV
= V
DRIVE
DD
Figure 4. AD7928 Dynamic Performance at 1 MSPS
AV
= V = 5.25V
DRIVE
DD
75
70
65
60
55
10
100
INPUT FREQUENCY (kHz)
1000
AV
AV
= V
= V
= 5.25V
= 4.75V
DD
DD
DRIVE
Figure 7. AD7928 THD vs. Analog Input Frequency for
Various Supply Voltages at 1 MSPS
DRIVE
AV
= V = 3.60V
DRIVE
DD
fSAMPLE = 1MSPS
= 25°C
RANGE = 0V TO REF
T
AV
= V = 2.70V
DRIVE
A
DD
IN
10
100
INPUT FREQUENCY (kHz)
1000
Figure 5. AD7928 SINAD vs. Analog Input Frequency for
Various Supply Voltages at 1 MSPS
Rev. D | Page 13 of 32
AD7908/AD7918/AD7928
–50
1.0
0.8
fSAMPLE = 1MSPS
= 25°C
RANGE = 0V TO REF
R
= 1000Ω
IN
AV
= V
= 5V
DD
DRIVE
T
A
–55
TEMPERATURE = 25°C
IN
AV
= 5.25V
DD
0.6
–60
–65
0.4
0.2
R
= 100Ω
IN
–70
–75
0
R
= 50Ω
IN
–0.2
–0.4
–0.6
–0.8
–1.0
R
= 10Ω
IN
–80
–85
–90
10
100
INPUT FREQUENCY (kHz)
1000
0
512
1024
1536
2048 2560 3072
CODE
3584 4096
Figure 8. AD7928 THD vs. Analog Input Frequency for
Various Source Impedances
Figure 10. AD7928 Typical DNL
1.0
0.8
AV
= V
= 5V
DD
DRIVE
TEMPERATURE = 25°C
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1.0
0
512
1024
1536 2048
CODE
2560 3072
3584 4096
Figure 9. AD7928 Typical INL
Rev. D | Page 14 of 32
AD7908/AD7918/AD7928
CONTROL REGISTER
The control register on the AD7908/AD7918/AD7928 is a 12-bit, write-only register. Data is loaded from the DIN pin of the
AD7908/AD7918/AD7928 on the falling edge of SCLK. The data is transferred on the DIN line at the same time that the conversion
result is read from the part. The data transferred on the DIN line corresponds to the AD7908/AD7918/AD7928 configuration for the next
conversion. This requires 16 serial clocks for every data transfer. Only the information provided on the first 12 falling clock edges (after
CS
falling edge) is loaded to the control register. MSB denotes the first bit in the data stream. The bit functions are outlined in Table 7.
MSB
LSB
CODING
WRITE
SEQ
DON’TCARE
ADD2
ADD1
ADD0
PM1
PM0
SHADOW
DON’TCARE
RANGE
Table 7. Control Register Bit Functions
Bit
Mnemonic Comment
11
WRITE
The value written to this bit of the control register determines whether or not the following 11 bits are loaded to the
control register. If this bit is a 1, the following 11 bits are written to the control register; if it is a 0, the remaining 11 bits
are not loaded to the control register, and it remains unchanged.
10
9
SEQ
The SEQ bit in the control register is used in conjunction with the SHADOW bit to control the use of the sequencer
function and access the SHADOW register (see the SHADOW register bit map).
DON’TCARE
8 to 6 ADD2 to
ADD0
These three address bits are loaded at the end of the present conversion sequence and select which analog input
channel is to be converted in the next serial transfer, or they can select the final channel in a consecutive sequence as
described in Table 10. The selected input channel is decoded as shown in Table 8. The address bits corresponding to
the conversion result are also output on DOUT prior to the 12 bits of data, see the Serial Interface section. The next
channel to be converted on is selected by the mux on the 14th SCLK falling edge.
5, 4
3
PM1, PM0
SHADOW
Power Management Bits. These two bits decode the mode of operation of the AD7908/AD7918/AD7928 as shown in
Table 9.
The SHADOW bit in the control register is used in conjunction with the SEQ bit to control the use of the sequencer
function and access the SHADOW register (see Table 10).
2
1
DON’TCARE
RANGE
This bit selects the analog input range to be used on the AD7908/AD7918/AD7928. If it is set to 0, the analog input
range extends from 0 V to 2 × REFIN. If it is set to 1, the analog input range extends from 0 V to REFIN (for the next
conversion). For 0 V to 2 × REFIN, AVDD = 4.75 V to 5.25 V.
0
CODING
This bit selects the type of output coding the AD7908/AD7918/AD7928 uses for the conversion result. If this bit is set to
0, the output coding for the part is twos complement. If this bit is set to 1, the output coding from the part is straight
binary (for the next conversion).
Table 8. Channel Selection
ADD2
ADD1
ADD0
Analog Input Channel
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
VIN0
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
VIN7
Rev. D | Page 15 of 32
AD7908/AD7918/AD7928
Table 9. Power Mode Selection
PM1 PM0 Mode
1
1
Normal Operation. In this mode, the AD7908/AD7918/AD7928 remain in full power mode regardless of the status of any of
the logic inputs. This mode allows the fastest possible throughput rate from the AD7908/AD7918/AD7928.
1
0
Full Shutdown. In this mode, the AD7908/ AD7918/AD7928 is in full shutdown mode with all circuitry powering down. The
AD7908/AD7918/AD7928 retains the information in the control register while in full shutdown. The part remains in full
shutdown until these bits are changed.
0
0
1
0
Auto Shutdown. In this mode, the AD7908/AD7918/AD7928 automatically enters full shutdown mode at the end of each
conversion when the control register is updated. Wake-up time from full shutdown is 1 μs and the user should ensure that 1 μs
has elapsed before attempting to perform a valid conversion on the part in this mode.
Invalid Selection. This configuration is not allowed.
SEQUENCER OPERATION
The configuration of the SEQ and SHADOW bits in the control register allows the user to select a particular mode of operation of the
sequencer function. Table 10 outlines the four modes of operation of the sequencer.
Table 10. Sequence Selection
SEQ SHADOW Sequence Type
0
0
This configuration means that the sequence function is not used. The analog input channel selected for each individual
conversion is determined by the contents of the ADD0 through ADD2 channel address bits in each prior write
operation. This mode of operation reflects the traditional operation of a multichannel ADC, without the sequencer
function being used, where each write to the AD7908/AD7918/AD7928 selects the next channel for conversion (see
Figure 11).
0
1
This configuration selects the SHADOW register for programming. The following write operation loads the contents of
the SHADOW register. This programs the sequence of channels to be converted on continuously with each successive
valid CS falling edge (see the SHADOW Register section, SHADOW register bit map, and Figure 12). The channels
selected need not be consecutive.
1
1
0
1
If the SEQ and SHADOW bits are set in this way, then the sequence functions are not interrupted upon completion of
the write operation. This allows other bits in the control register to be altered between conversions while in a sequence,
without terminating the cycle.
This configuration is used in conjunction with the ADD2 to ADD0 channel address bits to program continuous
conversions on a consecutive sequence of channels from Channel 0 to a selected final channel as determined by the
channel address bits in the control register (see Figure 13).
Rev. D | Page 16 of 32
AD7908/AD7918/AD7928
SHADOW REGISTER
MSB
LSB
VIN0
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
VIN7
VIN0
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
VIN7
Sequence One
Sequence Two
The SHADOW register on the AD7908/AD7918/AD7928 is a
16-bit, write-only register. Data is loaded from the DIN pin of
POWER-ON
DUMMY CONVERSION
DIN = ALL 1s
the AD7908/AD7918/AD7928 on the falling edge of SCLK. The
data is transferred on the DIN line at the same time that a
conversion result is read from the part. This requires 16 serial
clock falling edges for the data transfer. The information is
clocked into the SHADOW register, provided that the SEQ and
SHADOW bits were set to 0,1, respectively, in the previous
write to the control register. MSB denotes the first bit in the
data stream. Each bit represents an analog input from Channel 0
to Channel 7. Through programming the SHADOW register,
two sequences of channels can be selected, through which the
AD7908/AD7918/AD7928 cycle with each consecutive
conversion after the write to the SHADOW register.
DIN: WRITE TO CONTROL REGISTER,
CS
WRITE BIT = 1, SELECT CODING, RANGE,
AND POWER MODE.
SELECT A2 TO A0 FOR CONVERSION.
SEQ = SHADOW = 0
DOUT: CONVERSION RESULT FROM
PREVIOUSLY SELECTED
CHANNEL A2 TO A0.
CS
WRITE BIT = 1,
SEQ = SHADOW = 0
DIN: WRITE TO CONTROL REGISTER,
WRITE BIT = 1, SELECT CODING, RANGE,
AND POWER MODE.
SELECT A2 TO A0 FOR CONVERSION.
SEQ = SHADOW = 0
Figure 11. SEQ Bit = 0, SHADOW Bit = 0 Flowchart
Sequence One is performed first and then Sequence Two. If the
user does not wish to perform a second sequence option, then
all 0s must be written to the last 8 LSBs of the SHADOW
register. To select a sequence of channels, the associated channel
bit must be set for each analog input. The AD7908/AD7918/
AD7928 continuously cycle through the selected channels in
ascending order beginning with the lowest channel, until a
write operation occurs (that is, the WRITE bit is set to 1) with
the SEQ and SHADOW bits configured in any way except 1, 0,
(see Table 10). The bit functions are outlined in the SHADOW
register bit map.
POWER-ON
DUMMY CONVERSION
DIN = ALL 1s
DIN: WRITE TO CONTROL REGISTER,
WRITE BIT = 1, SELECT CODING, RANGE,
AND POWER MODE.
SELECT CHANNEL A2 TO A0
FOR CONVERSION.
SEQ = 0 SHADOW = 1
CS
DOUT: CONVERSION RESULT FROM
PREVIOUSLY SELECTED CHANNEL A2
TO A0.
Figure 11 reflects the traditional operation of a multichannel
ADC, where each serial transfer selects the next channel for
conversion. In this mode of operation the sequencer function is
not used.
CS
DIN: WRITE TO SHADOW REGISTER,
SELECTING WHICH CHANNELS TO
CONVERT ON; CHANNELS SELECTED
NEED NOT BE CONSECUTIVE
CHANNELS
WRITE BIT = 0
WRITE BIT = 1
Figure 12 shows how to program the AD7908/AD7918/AD7928
to continuously convert on a particular sequence of channels.
To exit this mode of operation and revert back to the traditional
mode of operation of a multichannel ADC (as outlined in
Figure 11), ensure that the WRITE bit = 1 and the SEQ =
SHADOW = 0 on the next serial transfer. Figure 13 shows how
a sequence of consecutive channels can be converted on without
having to program the SHADOW register or write to the part
on each serial transfer. Again, to exit this mode of operation and
revert back to the traditional mode of operation of a multichannel
ADC (as outlined in Figure 11), ensure the WRITE bit = 1 and
the SEQ = SHADOW = 0 on the next serial transfer.
SEQ = 1, SHADOW = 0
CONTINUOUSLY
CONVERTS ON THE
SELECTED SEQUENCE
OF CHANNELS BUT WILL
ALLOW RANGE, CODING,
AND SO ON, TO CHANGE
IN THE CONTROL
REGISTER WITHOUT
INTERRUPTING THE
SEQUENCE, PROVIDED
SEQ = 1 SHADOW = 0
CONTINUOUSLY
CONVERTS ON
THE SELECTED
SEQUENCE OF
CHANNELS
CS
WRITE BIT = 0
WRITE BIT = 0
WRITE BIT = 1
SEQ = 1, SHADOW = 0
Figure 12. SEQ Bit = 0, SHADOW Bit = 1 Flowchart
Rev. D | Page 17 of 32
AD7908/AD7918/AD7928
POWER-ON
REFIN or 0 V to 2 × REFIN. Figure 14 and Figure 15 show
simplified schematics of the ADC. The ADC is comprised of
control logic, SAR, and a capacitive DAC, which are used to add
and subtract fixed amounts of charge from the sampling
capacitor to bring the comparator back into a balanced
condition. Figure 14 shows the ADC during its acquisition
phase. SW2 is closed and SW1 is in Position A. The comparator
is held in a balanced condition and the sampling capacitor
acquires the signal on the selected VIN channel.
DUMMY CONVERSION
DIN = ALL 1s
DIN: WRITE TO CONTROL REGISTER,
WRITE BIT = 1, SELECT CODING, RANGE,
CS
AND POWER MODE.
SELECT CHANNEL A2 TO A0
FOR CONVERSION.
SEQ = 1 SHADOW = 1
DOUT: CONVERSION RESULT FROM
CHANNEL 0.
CAPACITIVE DAC
CONTINUOUSLY CONVERTS ON A
CONSECUTIVE SEQUENCE OF
CHANNELS FROM CHANNEL 0 UP TO,
AND INCLUDING, THE PREVIOUSLY
SELECTED A2 TO A0 IN THE CONTROL
REGISTER.
CS
WRITE BIT = 0
A
4kΩ
V
V
0
IN
CONTROL
LOGIC
SW1
B
SW2
7
IN
COMPARATOR
AGND
CONTINUOUSLY CONVERTS ON THE
SELECTED SEQUENCE OF CHANNELS
BUT WILL ALLOW RANGE, CODING, AND
SO ON, TO CHANGE IN THE CONTROL
REGISTER WITHOUT INTERRUPTING
THE SEQUENCE, PROVIDED SEQ = 1
SHADOW = 0
Figure 14. ADC Acquisition Phase
CS
WRITE BIT = 1
SEQ = 1, SHADOW = 0
When the ADC starts a conversion (see Figure 15), SW2 opens
and SW1 moves to Position B, causing the comparator to
become unbalanced. The control logic and the capacitive DAC
are used to add and subtract fixed amounts of charge from the
sampling capacitor to bring the comparator back into a
balanced condition. When the comparator is rebalanced, the
conversion is complete. The control logic generates the ADC
output code. Figure 17 and Figure 18 show the ADC transfer
functions.
Figure 13. SEQ Bit = 1, SHADOW Bit = 1 Flowchart
CIRCUIT INFORMATION
The AD7908/AD7918/AD7928 are high speed, 8-channel, 8-bit,
10-bit, and 12-bit, single-supply ADCs, respectively. The parts
can be operated from a 2.7 V to 5.25 V supply. When operated
from either a 5 V or 3 V supply, the AD7908/AD7918/AD7928
are capable of throughput rates of 1 MSPS when provided with
a 20 MHz clock.
CAPACITIVE DAC
A
4kΩ
The AD7908/AD7918/AD7928 provide the user with an on-
chip, track-and-hold ADC, and a serial interface housed in a
20-lead TSSOP package. The AD7908/AD7918/ AD7928 each
have eight single-ended input channels with a channel
V
V
0
7
IN
CONTROL
LOGIC
SW1
B
SW2
IN
COMPARATOR
AGND
sequencer, allowing the user to select a channel sequence that
Figure 15. ADC Conversion Phase
CS
the ADC can cycle through with each consecutive
falling
edge. The serial clock input accesses data from the part, controls
the transfer of data written to the ADC, and provides the clock
source for the successive approximation ADC. The analog input
range for the AD7908/AD7918/ AD7928 is 0 V to REFIN or 0 V
to 2 × REFIN, depending on the status of Bit 1 in the control
register. For the 0 to 2 × REFIN range, the part must be operated
from a 4.75 V to 5.25 V supply.
Analog Input
Figure 16 shows an equivalent circuit of the analog input
structure of the AD7908/AD7918/AD7928. The two diodes (D1
and D2) provide ESD protection for the analog inputs. Care
must be taken to ensure that the analog input signal never
exceeds the supply rails by more than 300 mV. This causes these
diodes to become forward biased and start conducting current
into the substrate. 10 mA is the maximum current these diodes
can conduct without causing irreversible damage to the part.
The Capacitor C1 in Figure 16 is typically about 4 pF and can
primarily be attributed to pin capacitance. The Resistor R1 is a
lumped component made up of the on resistance of the track-
and-hold switch and also includes the on resistance of the input
multiplexer. The total resistance is typically about 400 Ω. The
Capacitor C2 is the ADC sampling capacitor and has a
The AD7908/AD7918/AD7928 provide flexible power
management options to allow the user to achieve the best power
performance for a given throughput rate. These options are
selected by programming the PM1 and PM0 power
management bits in the control register.
CONVERTER OPERATION
The AD7908/AD7918/AD7928 are 8-, 10-, and 12-bit
capacitance of 30 pF typically. For ac applications, removing
high frequency components from the analog input signal is
recommended by use of an RC lowpass filter on the relevant
analog input pin. In applications where harmonic distortion
successive approximation analog-to-digital converters based
around a capacitive DAC, respectively. The AD7908/AD7918/
AD7928 can convert analog input signals in the range 0 V to
Rev. D | Page 18 of 32
AD7908/AD7918/AD7928
and signal-to-noise ratio are critical, the analog input should be
driven from a low impedance source. Large source impedances
significantly affect the ac performance of the ADC. This can
necessitate the use of an input buffer amplifier. The choice of
the op amp is a function of the particular application.
011…111
011…110
•
•
000…001
000…000
111…111
•
•
1LSB = 2 × V
1LSB = 2 × V
1LSB = 2 × V
/256 AD7908
/1024 AD7918
/4096 AD7928
REF
REF
REF
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum
source impedance depends on the amount of total harmonic
distortion (THD) that can be tolerated. The THD increases as
the source impedance increases, and performance degrades (see
Figure 8).
100…010
100…001
100…000
–V
+ 1 LSB
+V
– 1 LSB
REF
REF
V
– 1 LSB
REF
ANALOG INPUT
Figure 18. Twos Complement Transfer Characteristic
with REFIN REFIN Input Range
AV
DD
HANDLING BIPOLAR INPUT SIGNALS
C2
30pF
D1
R1
Figure 19 shows how useful the combination of the 2 × REFIN
input range and the twos complement output coding scheme is
for handling bipolar input signals. If the bipolar input signal is
biased about REFIN and twos complement output coding is
selected, then REFIN becomes the zero code point, −REFIN is
negative full scale and +REFIN becomes positive full scale, with
a dynamic range of 2 × REFIN.
V
IN
C1
4pF
D2
CONVERSION PHASE: SWITCH OPEN
TRACK PHASE: SWITCH CLOSED
Figure 16. Equivalent Analog Input Circuit
ADC TRANSFER FUNCTION
The output coding of the AD7908/AD7918/AD7928 is either
straight binary or twos complement, depending on the status of
the LSB in the control register. The designed code transitions
occur at successive LSB values (that is, 1 LSB, 2 LSBs, and so
on). The LSB size is REFIN/256 for the AD7908, REFIN/1024 for
the AD7918, and REFIN/4096 for the AD7928. The ideal transfer
characteristic for the AD7908/AD7918/AD7928 when straight
binary coding is selected is shown in Figure 17, and the ideal
transfer characteristic for the AD7908/AD7918/AD7928 when
twos complement coding is selected is shown in Figure 18.
TYPICAL CONNECTION DIAGRAM
Figure 20 shows a typical connection diagram for the
AD7908/AD7918/AD7928. In this setup, the AGND pin is
connected to the analog ground plane of the system. In Figure 20,
REFIN is connected to a decoupled 2.5 V supply from a reference
source, the AD780, to provide an analog input range of 0 V to
2.5 V (if RANGE bit is 1) or 0 V to 5 V (if RANGE bit is 0).
Although the AD7908/AD7918/AD7928 is connected to a VDD
of 5 V, the serial interface is connected to a 3 V microprocessor.
The VDRIVE pin of the AD7908/AD7918/ AD7928 is connected
to the same 3 V supply of the microprocessor to allow a 3 V
logic interface (see the Digital Inputs section). The conversion
result is output in a 16-bit word. This 16-bit data stream
consists of a leading zero, three address bits indicating which
channel the conversion result corresponds to, followed by the 12
bits of conversion data for the AD7928 (10 bits of data for the
AD7918 and 8 bits of data for the AD7908, each followed by
two and four trailing zeros, respectively). For applications
where power consumption is of concern, the power-down
modes should be used between conversions or bursts of several
conversions to improve power performance (see the Modes of
Operation section).
111…111
111…110
•
•
111…000
•
011…111
•
•
1LSB = V
1LSB = V
1LSB = V
/256 AD7908
/1024 AD7918
/4096 AD7928
REF
REF
REF
000…010
000…001
000…000
1 LSB
+V
– 1 LSB
REF
0V
ANALOG INPUT
NOTE
1. V
IS EITHER REF OR 2 × REF
REF
IN IN.
Figure 17. Straight Binary Transfer Characteristic
Rev. D | Page 19 of 32
AD7908/AD7918/AD7928
V
DD
V
REF
0.1µF
AV
DD
REF
IN
V
DD
V
DRIVE
AD7908/
AD7918/
AD7928
R4
DSP/µP
V
R3
R2
TWOS COMPLEMENT
V
V
0
DOUT
IN
V
0V
•
•
011…111
000…000
100…000
+REF
(= 2 × REF
IN)
R1
IN
7
IN
R1 = R2 = R3 = R4
REF
IN
(= 0V)
–REF
IN
Figure 19. Handling Bipolar Signals
during the sequence, then it must be ensured that the SEQ and
SHADOW bits are set to 1, 0 to avoid interrupting the
5V
SUPPLY
SERIAL
INTERFACE
0.1µF
10µF
automatic conversion sequence. This pattern continues until
such time as the AD7908/AD7918/AD7928 is written to and the
SEQ and SHADOW bits are configured with any bit combination
except 1, 0. On completion of the sequence, the AD7908/
AD7918/AD7928 sequencer returns to the first selected channel
in the SHADOW register and commence the sequence again.
AV
0
•
•
DD
SCLK
DOUT
CS
V
V
IN
AD7908/
AD7918/
AD7928
0V TO REF
IN
µC/µP
7
IN
DIN
REF
V
DRIVE
AGND
IN
2.5V
0.1µF
Rather than selecting a particular sequence of channels, a
number of consecutive channels beginning with Channel 0 can
also be programmed via the control register alone, without
needing to write to the SHADOW register. This is possible if the
SEQ and SHADOW bits are set to 1,1. The channel address bits
ADD2 through ADD0 then determine the final channel in the
consecutive sequence. The next conversion is on Channel 0,
then Channel 1, and so on until the channel selected via the
address bits ADD2 through ADD0 is reached. The cycle begins
again on the next serial transfer, provided the WRITE bit is set
to low, or if high, that the SEQ and SHADOW bits are set to
1, 0; then the ADC continues its preprogrammed automatic
sequence uninterrupted.
0.1µF
10µF
AD780
3V
SUPPLY
NOTE
1. ALL UNUSED INPUT CHANNELS SHOULD BE CONNECTED TO AGND.
Figure 20. Typical Connection Diagram
Analog Input Selection
Any one of eight analog input channels can be selected for
conversion by programming the multiplexer with the Address
Bit ADD2 to Address Bit ADD0 in the control register. The
channel configurations are shown in Table 8. The AD7908/
AD7918/AD7928 can also be configured to automatically cycle
through a number of channels as selected. The sequencer
feature is accessed via the SEQ and SHADOW bits in the
control register (see Table 10).
Regardless of which channel selection method is used, the 16-bit
word output from the AD7928 during each conversion always
contains a leading zero, three channel address bits that the
conversion result corresponds to, followed by the 12-bit
conversion result. The AD7918 outputs a leading zero, three
channel address bits that the conversion result corresponds to,
followed by the 10-bit conversion result and two trailing zeros;
the AD7908 outputs a leading zero, three channel address bits
that the conversion result corresponds to, followed by the 8-bit
conversion result and four trailing zeros. (See the Serial
Interface section.)
The AD7908/AD7918/AD7928 can be programmed to
continuously convert on a selection of channels in ascending
order. The analog input channels to be converted on are
selected through programming the relevant bits in the
SHADOW register (see the SHADOW Register section). The
next serial transfer then acts on the sequence programmed by
executing a conversion on the lowest channel in the selection.
The next serial transfer results in a conversion on the next
highest channel in the sequence, and so on.
It is not necessary to write to the control register once a
sequencer operation has been initiated. The WRITE bit must be
set to zero or the DIN line tied low to ensure the control register
is not accidentally overwritten, or the sequence operation
interrupted. If the control register is written to at any time
Digital Inputs
The digital inputs applied to the AD7908/AD7918/AD7928 are
not limited by the maximum ratings that limit the analog
Rev. D | Page 20 of 32
AD7908/AD7918/AD7928
inputs. Instead, the digital inputs applied can go to 7 V and are
not restricted by the AVDD + 0.3 V limit as on the analog inputs.
CS
and the
The conversion is initiated on the falling edge of
track-and-hold enters hold mode as described in the Serial
Interface section. The data presented to the AD7908/AD7918/
AD7928 on the DIN line during the first 12 clock cycles of the
data transfer are loaded into the control register (provided
WRITE bit is set to 1). If data is to be written to the SHADOW
register (SEQ = 0, SHADOW = 1 on previous write), data
presented on the DIN line during the first 16 SCLK cycles is
loaded into the SHADOW register. The part remains fully
powered up in normal mode at the end of the conversion as
long as PM1 and PM0 are both loaded with 1 on every data
transfer.
CS
Another advantage of SCLK, DIN, and
not being restricted
by the AVDD + 0.3 V limit is the fact that power supply
CS
sequencing issues are avoided. If , DIN, or SCLK are applied
before AVDD, there is no risk of latch-up as there would be on
the analog inputs if a signal greater than 0.3 V was applied prior
to AVDD
.
VDRIVE
The AD7908/AD7918/AD7928 also have the VDRIVE feature.
VDRIVE controls the voltage at which the serial interface operates.
VDRIVE allows the ADC to easily interface to both 3 V and 5 V
processors. For example, if the AD7908/AD7918/AD7928 were
operated with an AVDD of 5 V, the VDRIVE pin could be powered
from a 3 V supply. The AD7908/AD7918/AD7928 have better
dynamic performance with an AVDD of 5 V while still being able
to interface to 3 V processors. Care should be taken to ensure
Sixteen serial clock cycles are required to complete the
conversion and access the conversion result. The track-and-
CS
hold goes back into track on the 14th SCLK falling edge.
then idle high until the next conversion or can idle low until
CS
can
sometime prior to the next conversion, effectively idling
low.
Once a data transfer is complete (DOUT has returned to three-
state), another conversion can be initiated after the quiet time,
V
DRIVE does not exceed AVDD by more than 0.3 V. See the
Absolute Maximum Ratings section.
CS
tQUIET, has elapsed by bringing
low again.
Reference
CS
An external reference source should be used to supply the 2.5 V
reference to the AD7908/AD7918/AD7928. Errors in the
reference source results in gain errors in the AD7908/
AD7918/AD7928 transfer function and adds to the specified
full-scale errors of the part. A capacitor of at least 0.1 μF should
be placed on the REFIN pin. Suitable reference sources for the
AD7908/AD7918/AD7928 include the AD780, REF192,
AD1582, ADR03, ADR381, ADR391, and ADR421.
1
16
12
SCLK
1 LEADING ZERO + 3 CHANNEL
DOUT
IDENTIFIER BITS + CONVERSION RESULT
DATA IN TO CONTROL/SHADOW REGISTER
DIN
NOTES
1. CONTROL REGISTER DATA IS LOADED ON FIRST 12 SCLK CYCLES.
2. SHADOW REGISTER DATA IS LOADED ON FIRST 16 SCLK CYCLES.
If 2.5 V is applied to the REFIN pin, the analog input range can
either be 0 V to 2.5 V or 0 V to 5 V, depending on the setting of
the RANGE bit in the control register.
Figure 21. Normal Mode Operation
Full Shutdown Mode (PM1 = 1, PM0 = 0)
In this mode, all internal circuitry on the AD7908/AD7918/
AD7928 is powered down. The part retains information in the
control register during full shutdown. The AD7908/AD7918/
AD7928 remains in full shutdown until the power management
bits in the control register, PM1 and PM0, are changed.
MODES OF OPERATION
The AD7908/AD7918/AD7928 have a number of different
modes of operation. These modes are designed to provide
flexible power management options. These options can be
chosen to optimize the power dissipation/throughput rate ratio
for differing application requirements. The mode of operation
of the AD7908/AD7918/AD7928 is controlled by the power
management bits, PM1 and PM0, in the control register, as
detailed in Table 9. When power supplies are first applied to the
AD7908/AD7918/AD7928, care should be taken to ensure that
the part is placed in the required mode of operation (see
Powering Up the AD7908/AD7918/AD7928 section).
If a write to the control register occurs while the part is in full
shutdown, with the power management bits changed to PM0 =
CS
PM1 = 1, normal mode, the part begins to power up on the
rising edge. The track-and-hold that was in hold while the part was
in full shutdown returns to track on the 14th SCLK falling edge.
To ensure that the part is fully powered up, tPOWER UP, should
CS
have elapsed before the next
falling edge. Figure 22 shows
Normal Mode (PM1 = PM0 = 1)
the general diagram for this sequence.
This mode is intended for the fastest throughput rate
Auto Shutdown Mode (PM1 = 0, PM0 = 1)
performance, as the user does not have to worry about any
power-up times with the AD7908/AD7918/AD7928 remaining
fully powered at all times. Figure 21 shows the general diagram
of the operation of the AD7908/AD7918/AD7928 in this mode.
In this mode, the AD7908/AD7918/AD7928 automatically
enters shutdown at the end of each conversion when the control
register is updated. When the part is in shutdown, the track and
hold is in hold mode. Figure 23 shows the general diagram of
Rev. D | Page 21 of 32
AD7908/AD7918/AD7928
the operation of the AD7908/AD7918/AD7928 in this mode. In
shutdown mode, all internal circuitry on the AD7908/AD7918/
AD7928 is powered down. The part retains information in the
control register during shutdown. The AD7908/AD7918/
other conversion result being valid. In this mode, the power
consumption of the part is greatly reduced with the part
entering shutdown at the end of each conversion. When the
control register is programmed to move into auto shutdown, it
does so at the end of the conversion. The user can move the
CS
AD7928 remains in shutdown until the next
falling edge it
falling edge, the track-and-hold that was in
CS
ADC in and out of the low power state by controlling the
signal.
CS
receives. On this
hold while the part was in shutdown returns to track. Wakeup
time from auto shutdown is 1 μs, and the user should ensure
that 1 μs has elapsed before attempting a valid conversion.
When running the AD7908/AD7918/AD7928 with a 20 MHz
clock, one dummy cycle should be sufficient to ensure the part
is fully powered up. During this dummy cycle the contents of
the control register should remain unchanged; therefore the
WRITE bit should be 0 on the DIN line. This dummy cycle
effectively halves the throughput rate of the part, with every
Powering Up the AD7908/AD7918/AD7928
When supplies are first applied to the AD7908/AD7918/
AD7928, the ADC can power up in any of the operating modes
of the part. To ensure the part is placed into the required
operating mode, the user should perform a dummy cycle
operation as outlined in Figure 24.
PART IS IN
FULL SHUTDOWN
PART BEG I NSTO POWER UP ON
CS RISING EDGE AS PM1 = PM0 = 1
THE PART IS FULLY POWERED UP
ONCE tPOWER UP HAS ELAPSED
t12
CS
14
16
1
1
14
16
SCLK
DOUT
DIN
CHANNEL IDENTIFIER BITS + CONVERSION RESULT
DATA IN TO CONTROL/SHADOW REGISTER
DATA IN TO CONTROL REGISTER
CONTROL REGISTER IS LOADED ON THE FIRST 12 CLOCKS.
PM1 = 1, PM0 = 1
TO KEEPTHE PART IN NORMAL MODE,
LOAD PM1 = PM0 = 1 IN CONTROL REGISTER
Figure 22. Full Shutdown Mode Operation
PART ENTERS SHUTDOWN
ON CS RISING EDGE
AS PM1 = 0, PM0 = 1
PART BEGINS TO POWER
UP ON CS FALLING EDGE
PART ENTERS SHUTDOWN ON CS
RISING EDGE AS PM1 = 0, PM0 = 1
PART IS FULLY
POWERED UP
CS
DUMMY CONVERSION
12
1
12
16
1
16
1
12
16
SCLK
CHANNEL IDENTIFIER
BITS + CONVERSION RESULT
CHANNEL IDENTIFIER
BITS + CONVERSION RESULT
DOUT
INVALID DATA
DATA IN TO CONTROL/SHADOW REGISTER
DATA IN TO CONTROL/SHADOW REGISTER
DIN
CONTROL REGISTER IS LOADED ON THE
FIRST 12 CLOCKS, PM1 = 0, PM0 = 1
TO KEEP PART IN THIS MODE, LOAD PM1 = 0,
PM0 = 1 IN CONTROL REGISTER OR SET WRITE BIT = 0
CONTROL REGISTER CONTENTS SHOULD
NOT CHANGE. WRITE BIT = 0
Figure 23. Auto Shutdown Mode Operation
Rev. D | Page 22 of 32
AD7908/AD7918/AD7928
CORRECT VALUE IN CONTROL
REGISTER, VALID DATA FROM
NEXT CONVERSION, USER CAN
WRITE TO SHADOW REGISTER
IN NEXT CONVERSION
CS
DUMMY CONVERSION
12
DUMMY CONVERSION
12
1
16
1
16
1
12
16
SCLK
DOUT
INVALID DATA
INVALID DATA
INVALID DATA
DATA IN TO CONTROL REGISTER
DIN
KEEP DIN LINE TIED HIGH FOR FIRST TWO DUMMY CONVERSIONS
CONTROL REGISTER IS LOADED ON THE FIRST
12 CLOCK EDGES
Figure 24. Placing AD7928 into the Required Operating Mode After Supplies are Applied
10
POWER VS. THROUGHPUT RATE
By operating in auto shutdown mode on the AD7908/AD7918/
AD7928, the average power consumption of the ADC decreases
at lower throughput rates. Figure 25 shows how as the
throughput rate is reduced, the part remains in its shutdown
state longer and the average power consumption over time
drops accordingly.
AV = 5V
DD
AV = 3V
DD
1
0.1
For example, if the AD7928 is operated in a continuous
sampling mode with a throughput rate of 100 kSPS and an
SCLK of 20 MHz (AVDD = 5 V), and the device is placed in auto
shutdown mode, that is, if PM1 = 0 and PM0 = 1, then the
power consumption is calculated as follows:
0.01
0
50
100
150
200
250
300
350
THROUGHPUT (kSPS)
The maximum power dissipation during normal operation is
13.5 mW (AVDD = 5 V). If the power-up time from auto
shutdown is one dummy cycle, that is, 1 μs, and the remaining
conversion time is another cycle, that is, 1 μs, then the AD7928
can be said to dissipate 13.5 mW for 2 μs during each
conversion cycle. For the remainder of the conversion cycle,
8 μs, the part remains in auto shutdown mode. The AD7928 can
be said to dissipate 2.5 μW for the remaining 8 μs of the
conversion cycle. If the throughput rate is 100 kSPS, the cycle
time is 10 μs and the average power dissipated during each cycle is
Figure 25. AD7928 Power vs. Throughput Rate
SERIAL INTERFACE
Figure 26, Figure 27, and Figure 28 show the detailed timing
diagrams for serial interfacing to the AD7908, AD7918, and
AD7928, respectively. The serial clock provides the conversion
clock and also controls the transfer of information to and from
the AD7908/AD7918/AD7928 during each conversion.
CS
The
signal initiates the data transfer and conversion process.
CS
The falling edge of
puts the track-and-hold into hold mode,
(2/10) × (13.5 mW) + (8 / 10) × (2.5 μW) = 2.702 mW
takes the bus out of three-state; the analog input is sampled at
this point. The conversion is also initiated at this point and
requires 16 SCLK cycles to complete. The track-and-hold goes
back into track on the 14th SCLK falling edge as shown in
Figure 26, Figure 27, and Figure 28 at Point B, except when the
write is to the SHADOW register, in which case the track-and-
Figure 25 shows the maximum power vs. throughput rate when
using the auto shutdown mode with 3 V and 5 V supplies.
CS
hold does not return to track until the rising edge of , that is,
Point C in Figure 29. On the 16th SCLK falling edge, the DOUT
CS
line goes back into three-state. If the rising edge of
occurs
before 16 SCLKs have elapsed, the conversion is terminated, the
DOUT line goes back into three-state, and the control register is
not updated; otherwise DOUT returns to three-state on the
16th SCLK falling edge as shown in Figure 26, Figure 27, and
Figure 28. Sixteen serial clock cycles are required to perform the
conversion process and to access data from the AD7908/
AD7918/AD7928. For the AD7908/AD7918/AD7928, the
Rev. D | Page 23 of 32
AD7908/AD7918/AD7928
8/10/12 bits of data are preceded by a leading zero and the
3-channel address bits (ADD2 to ADD0) identify which
MICROPROCESSOR INTERFACING
The serial interface on the AD7908/AD7918/AD7928 allows the
part to be directly connected to a range of many different
microprocessors. This section explains how to interface the
AD7908/AD7918/AD7928 with some of the more common
microcontroller and DSP serial interface protocols.
CS
channel the result corresponds to.
going low provides the
leading zero to be read in by the microcontroller or DSP. The
three remaining address bits and data bits are then clocked out
by subsequent SCLK falling edges beginning with the first
address bit (ADD2). Thus the first falling clock edge on the
serial clock has a leading zero provided and also clocks out
Address Bit ADD2. The final bit in the data transfer is valid on
the 16th falling edge, having been clocked out on the previous
(15th) falling edge.
AD7908/AD7918/AD7928 to TMS320C541
The serial interface on the TMS320C541 uses a continuous
serial clock and frame synchronization signals to synchronize
the data transfer operations with peripheral devices like the
CS
AD7908/AD7918/AD7928. The
input allows easy
Writing of information to the control register takes place on the
first 12 falling edges of SCLK in a data transfer, assuming the
MSB, that is, the WRITE bit, has been set to 1. If the control
register is programmed to use the SHADOW register, then
writing of information to the SHADOW register takes place on
all 16 SCLK falling edges in the next serial transfer, as shown for
example on the AD7928 in Figure 29. Two sequence options
can be programmed in the SHADOW register. If the user does
not want to program a second sequence, then the eight LSBs
should be filled with zeros. The SHADOW register is updated
interfacing between the TMS320C541 and the AD7908/
AD7918/AD7928 without any glue logic required. The serial
port of the TMS320C541 is set up to operate in burst mode with
internal CLKX0 (Tx serial clock on Serial Port 0) and FSX0 (Tx
frame sync from Serial Port 0). The serial port control register
(SPC) must have the following setup: FO = 0, FSM = 1, MCM = 1,
and TXM = 1. The connection diagram is shown in Figure 30. It
should be noted that for signal processing applications, it is
imperative that the frame synchronization signal from the
TMS320C541 provides equidistant sampling. The VDRIVE pin of
the AD7908/AD7918/AD7928 takes the same supply voltage as
that of the TMS320C541. This allows the ADC to operate at a
higher voltage than the serial interface, that is, TMS320C541, if
necessary.
CS
upon the rising edge of
and the track-and-hold begins to
track the first channel selected in the sequence.
The AD7908 outputs a leading zero and three channel address
bits that the conversion result corresponds to, followed by the
8-bit conversion result and four trailing zeros. The AD7918
outputs a leading zero and three channel address bits that the
conversion result corresponds to, followed by the 10-bit
conversion result and two trailing zeros. The 16-bit word read
from the AD7928 always contains a leading zero and three
channel address bits that the conversion result corresponds to,
followed by the 12-bit conversion result.
Rev. D | Page 24 of 32
AD7908/AD7918/AD7928
CS
tCONVERT
5 6
t2
t6
B
11
12
13
14
t5
15
16
t11
1
2
3
4
SCLK
t7
DB6
t3
t4
ADD0
THREE IDENTIFICATION BITS
t8
tQUIET
ADD2
ADD1
DB7
DB0
ZERO
ZERO
ZERO
ZERO
DOUT
THREE-STATE
THREE-STATE
FOUR TRAILING ZEROS
ZERO
t10
ADD0
t9
CODING
WRITE SEQ1
DONTC
ADD2
ADD1
DONTC DONTC
DONTC
DONTC
DIN
Figure 26. AD7908 Serial Interface Timing Diagram
CS
tCONVERT
t2
t6
B
11
12
13
14
t5
15
16
1
2
3
4
5
6
SCLK
t11
t7
t3
t4
t8
tQUIET
ADD2
ADD1
ADD0
DB7
DB6
DB2
DB1
DB0
ZERO
ZERO
DOUT
THREE-STATE
THREE-STATE
THREE IDENTIFICATION BITS
TWO TRAILING ZEROS
ZERO
t10
t9
WRITE
SEQ
DONTC
ADD2
ADD1
ADD0
CODING
DONTC DONTC
DONTC
DONTC
DIN
Figure 27. AD7918 Serial Interface Timing Diagram
CS
tCONVERT
t6
tQUIET
B
t2
13
16
t11
1
2
3
4
5
6
14
t5
15
SCLK
t7
t3
t8
DB0
t4
DOUT
ADD2
ADD1
ADD0
DB11
DB10
DB2
DB1
THREE-STATE
THREE-STATE
THREE IDENTIFICATION BITS
t9
t10
ZERO
DIN
WRITE
SEQ
DONTC
ADD2
ADD1
ADD0
DONTC DONTC
DONTC
Figure 28. AD7928 Serial Interface Timing Diagram
C
CS
tCONVERT
t6
t2
13
16
t11
1
2
3
4
5
6
SCLK
14
t5
15
t3
t7
t8
t4
ADD2
ADD1
ADD0
DB11
DB10
DB2
DB1
DB0
DOUT
DIN
THREE-STATE
THREE-STATE
THREE IDENTIFICATION BITS
t9
t10
4
ZERO
V
0
V
1
V
2
V
3
V
V
5
IN
V
6
V 7
IN
IN
IN
IN
IN
IN
IN
SEQUENCE 1
SEQUENCE 2
Figure 29. AD7928 Writing to SHADOW Register Timing Diagram
Rev. D | Page 25 of 32
AD7908/AD7918/AD7928
TMS320C5411
CLKX
AD7908/
AD7918/
AD79281
The timer register, for example, is loaded with a value that
provides an interrupt at the required sample interval. When an
interrupt is received, a value is transmitted with TFS/DT (ADC
control word). The TFS is used to control the RFS and thus the
reading of data. The frequency of the serial clock is set in the
SCLKDIV register. When the instruction to transmit with TFS
is given (that is, AX0 = TX0), the state of the SCLK is checked.
The DSP waits until the SCLK has gone high, low, and high
before transmission can start. If the timer and SCLK values are
chosen, such that the instruction to transmit occurs on or near
the rising edge of SCLK, then the data can be transmitted or it
can wait until the next clock edge.
SCLK
CLKR
DR
DOUT
DIN
DT
FSX
FSR
CS
V
DRIVE
1
ADDITIONAL PINS REMOVED FOR CLARITY.
V
DD
Figure 30. Interfacing to the TMS320C541
AD7908/AD7918/AD7928 to ADSP-21xx
For example, if the ADSP-2189 had a 20 MHz crystal such that
it had a master clock frequency of 40 MHz, then the master
cycle time would be 25 ns. If the SCLKDIV register was loaded
with the value 3, then an SCLK of 5 MHz is obtained, and eight
master clock periods elapse for every one SCLK period.
Depending on the throughput rate selected, if the timer register
is loaded with the value, say 803 (803 + 1 = 804), 100.5 SCLKs
occur between interrupts and subsequently between transmit
instructions. This situation results in nonequidistant sampling
as the transmit instruction is occurring on a SCLK edge. If the
number of SCLKs between interrupts is a whole integer figure
of N, then equidistant sampling is implemented by the DSP.
The ADSP-21xx family of DSPs are interfaced directly to the
AD7908/AD7918/AD7928 without any glue logic required. The
VDRIVE pin of the AD7908/AD7918/AD7928 takes the same
supply voltage as that of the ADSP-21xx. This allows the ADC
to operate at a higher voltage than the serial interface, that is,
ADSP-21xx, if necessary.
The SPORT0 control register should be set up as follows:
TFSW = RFSW = 1, alternate framing
INVRFS = INVTFS = 1, active low frame signal
DTYPE = 00, right justify data
SLEN = 1111, 16-bit data-words
ISCLK = 1, internal serial clock
TFSR = RFSR = 1, frame every word
IRFS = 0
AD7908/AD7918/AD7928 to DSP563xx
The connection diagram in Figure 32 shows how the
AD7908/AD7918/AD7928 can be connected to the synchronous
serial interface (ESSI) of the DSP563xx family of DSPs from
Motorola. Each ESSI (two on board) is operated in synchronous
mode (SYN bit in CRB = 1) with internally generated word
length frame sync for both Tx and Rx (Bit FSL1 = 0 and
Bit FSL0 = 0 in CRB). Normal operation of the ESSI is selected
by making MOD = 0 in the CRB. Set the word length to 16 by
setting Bit WL1 = 1 and Bit WL0 = 0 in CRA. The FSP bit in the
CRB should be set to 1 so the frame sync is negative. It should
be noted that for signal processing applications, it is imperative
that the frame synchronization signal from the DSP563xx
provides equidistant sampling.
ITFS = 1
The connection diagram is shown in Figure 31. The ADSP-21xx
has the TFS and RFS of the SPORT tied together, with TFS set
as an output and RFS set as an input. The DSP operates in
alternate framing mode and the SPORT control register is set
up as described. The frame synchronization signal generated on
CS
the TFS is tied to , as with all signal processing applications
where equidistant sampling is necessary. However, in this
example the timer interrupt is used to control the sampling rate
of the ADC, and under certain conditions equidistant sampling
cannot be achieved.
ADSP-21xx1
AD7908/
In the example shown in Figure 32, the serial clock is taken
from the ESSI so the SCK0 pin must be set as an output, SCKD
= 1. The VDRIVE pin of the AD7908/AD7918/AD7928 takes the
same supply voltage as that of the DSP563xx. This allows the
ADC to operate at a higher voltage than the serial interface, that
is, DSP563xx, if necessary.
AD7918/
AD79281
SCLK
DOUT
CS
SCLK
DR
RFS
TFS
DT
DIN
V
DRIVE
1
ADDITIONAL PINS REMOVED FOR CLARITY.
V
DD
Figure 31. Interfacing to the ADSP-21xx
Rev. D | Page 26 of 32
AD7908/AD7918/AD7928
DSP563xx1
supply line. Fast switching signals, like clocks, should be
shielded with digital ground to avoid radiating noise to other
sections of the board, and clock signals should never be run
near the analog inputs. Avoid crossover of digital and analog
signals. Traces on opposite sides of the board should run at
right angles to each other. This reduces the effects of
AD7908/
AD7918/
AD79281
SCK
SCLK
SRD
DOUT
DIN
STD
SC2
CS
feedthrough through the board. A microstrip technique is by far
the best, but is not always possible with a double sided board. In
this technique, the component side of the board is dedicated to
ground planes while signals are placed on the solder side.
V
DRIVE
1
ADDITIONAL PINS REMOVED FOR CLARITY.
V
DD
Figure 32. Interfacing to the DSP563xx
Good decoupling is also important. All analog supplies should
be decoupled with 10 μF tantalum in parallel with 0.1 μF
capacitors to AGND. To achieve the best performance from
these decoupling components, they must be placed as close as
possible to the device, ideally right up against the device. The
0.1 μF capacitors should have low effective series resistance
(ESR) and effective series inductance (ESI), such as the
common ceramic types or surface mount types, which provide a
low impedance path to ground at high frequencies to handle
transient currents due to internal logic switching.
APPLICATION HINTS
Grounding and Layout
The AD7908/AD7918/AD7928 have very good immunity to
noise on the power supplies, as can be seen by the PSRR vs.
Supply Ripple Frequency plot, Figure 6. However, care should
still be taken with regard to grounding and layout.
The printed circuit board that houses the AD7908/AD7918/
AD7928 should be designed so that the analog and digital
sections are separated and confined to certain areas of the
board. This facilitates the use of ground planes that can be
separated easily. A minimum etch technique is generally best
for ground planes as it gives the best shielding.
Evaluating the AD7908/AD7918/AD7928 Performance
The recommended layout for the AD7908/AD7918/AD7928 is
outlined in the AD7908/AD7918/AD7928 evaluation board.
The evaluation board package includes a fully assembled and
tested evaluation board, documentation, and software for
controlling the board from the PC via the eval-board controller.
All four AGND pins of the AD7908/AD7918/AD7928 should
be sunk in the AGND plane. If the AD7908/AD7918/AD7928
is in a system where multiple devices require an AGND to
DGND connection, the connection should be made at only one
point in the plane. Using a star ground point, the connection
should be established as close as possible to the AD7908/
AD7918/AD7928.
The eval-board controller can be used in conjunction with the
AD7908/AD7918/AD7928 evaluation board, as well as many
other Analog Devices evaluation boards ending in the CB
designator, to demonstrate/evaluate the ac and dc performance
of the AD7908/AD7918/AD7928.
Avoid running digital lines under the device, as these couple
noise onto the die. The analog ground plane should be allowed
to run under the AD7908/AD7918/AD7928 to avoid noise
coupling. The power supply lines to the AD7908/AD7918/
AD7928 should use as large a trace as possible to provide low
impedance paths and reduce the effects of glitches on the power
The software allows the user to perform ac (fast Fourier
transform) and dc (histogram of codes) tests on the
AD7908/AD7918/AD7928. The software and documentation
are on a CD shipped with the evaluation board.
Rev. D | Page 27 of 32
AD7908/AD7918/AD7928
OUTLINE DIMENSIONS
6.60
6.50
6.40
20
11
10
4.50
4.40
4.30
6.40 BSC
1
PIN 1
0.65
BSC
1.20 MAX
0.15
0.05
0.20
0.09
0.75
0.60
0.45
8°
0°
0.30
0.19
COPLANARITY
0.10
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-153-AC
Figure 33. 20-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-20)
Dimensions shown in millimeters
Rev. D | Page 28 of 32
AD7908/AD7918/AD7928
ORDERING GUIDE
Model1, 2, 3, 4
AD7908BRU-REEL
AD7908BRU-REEL7
AD7908BRUZ
AD7908BRUZ-REEL
AD7908BRUZ-REEL7
AD7908WYRUZ-REEL7
AD7918BRU-REEL7
AD7918BRUZ
AD7918BRUZ-REEL
AD7918BRUZ-REEL7
AD7918WYRUZ-REEL7
AD7928BRU
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +125°C
Linearity Error (LSB)5
Package Description
Package Option
RU-20
RU-20
0.2
0.2
0.2
0.2
0.2
0.2
0.5
0.5
0.5
0.5
0.5
1
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
20-Lead TSSOP
Evaluation Board
Controller Board
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
AD7928BRU-REEL
AD7928BRUZ
1
1
1
1
AD7928BRUZ-REEL
AD7928BRUZ-REEL7
AD7928WYRUZ-REEL7
EVAL-AD79x8CBZ
EVAL-CONTROL BRD
1
1 Z = RoHS Compliant Part.
2 W = Qualified for Automotive Applications.
3 The EVAL-AD79x8CBZ can be used as a standalone evaluation board or in conjunction with the evaluation controller board for evaluation/demonstration purposes.
The board comes with one chip of each the AD7908, AD7918, and AD7928.
4 The EVAL-CONTROL BRD is a complete unit allowing a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators. To
order a complete evaluation kit, order the particular ADC evaluation board, such as the EVAL-AD79x8CB, the EVAL-CONTROL BRD2, and a 12 V ac transformer. See the
relevant evaluation board technical note for more information.
5 Linearity error here refers to integral linearity error.
AUTOMOTIVE PRODUCTS
The AD72x8W models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
Rev. D | Page 29 of 32
AD7908/AD7918/AD7928
NOTES
Rev. D | Page 30 of 32
AD7908/AD7918/AD7928
NOTES
Rev. D | Page 31 of 32
AD7908/AD7918/AD7928
NOTES
©2006–2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03089-0-12/10(D)
Rev. D | Page 32 of 32
相关型号:
AD7920AKS
IC 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO6, PLASTIC, MO-203AB, SC-70, 6 PIN, Analog to Digital Converter
ADI
©2020 ICPDF网 联系我们和版权申明