AD7817_15 [ADI]
Dual, Low Power CMOS, Analog Front End with DSP Microcomputer;型号: | AD7817_15 |
厂家: | ADI |
描述: | Dual, Low Power CMOS, Analog Front End with DSP Microcomputer |
文件: | 总20页 (文件大小:1587K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Dual, Low Power CMOS, Analog Front End
with DSP Microcomputer
Data Sheet
AD7817/AD7818
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
REF
V
DD
IN
10-bit ADC with 9 µs conversion time
1 AD7818 and 4 AD7817 single-ended analog input channels
On-chip temperature sensor
Resolution of 0.25°C
2°C error from −40°C to +85°C
−55°C to +125°C operating range
Wide operating supply range: 2.7 V to 5.5 V
Inherent track-and-hold functionality
On-chip reference (2.5 V 1%)
AD7817
OVERTEMP
REG
B
A > B
A
OTI
TEMP
SENSOR
CHARGE
REDISTRIBUTION
DAC
REF
2.5V
DATA
OUT
D
OUT
V
V
V
V
IN1
IN2
IN3
IN4
MUX
CONTROL
LOGIC
REG
CONTROL
SAMPLING
CAPACITOR
D
IN
SCLK
RD/WR
CS
V
CLOCK
BALANCE
Overtemperature indicator
AGND
DGND
BUSY
CONVST
Automatic power-down at the end of a conversion
Low power operation
Figure 1. AD7817 Functional Block Diagram
4 µW at a throughput rate of 10 SPS
40 µW at a throughput rate of 1 kSPS
400 µW at a throughput rate of 10 kSPS
Flexible serial interface
V
DD
AD7818
OVERTEMP
REG
B
A > B
A
OTI
TEMP
SENSOR
REF
2.5V
CHARGE
REDISTRIBUTION
DAC
DATA
OUT
APPLICATIONS
D
V
IN/OUT
Data acquisition systems with ambient temperature
monitoring
IN1
MUX
CONTROL
LOGIC
SAMPLING
CAPACITOR
CONTROL
REG
SCLK
Industrial process control
Automotive
RD/WR
V
CLOCK
GENERATOR
BALANCE
Battery charging applications
AGND
CONVST
Figure 2. AD7818 Functional Block Diagram
GENERAL DESCRIPTION
The AD7817/AD7818 are 10-bit, single- and 4-channel analog-to-
digital converters (ADCs) with an on-chip temperature sensor that
can operate from a single 2.7 V to 5.5 V power supply. Each part
contains a 9 µs successive approximation converter based around
a capacitor digital-to-analog converter (DAC), an on-chip
temperature sensor with an accuracy of 2°C, an on-chip clock
oscillator, inherent track-and-hold functionality, and an on-chip
reference (2.5 V).
information, refer to the AD7817 Serial Interface section and
the AD7818 Serial Interface Mode section.
The AD7817 is available in a narrow body, 0.15 inch, 16-lead
SOIC and a 16-lead TSSOP, and the AD7818 comes in an 8-lead
SOIC and an 8-lead MSOP.
PRODUCT HIGHLIGHTS
1. The devices have an on-chip temperature sensor that allows
an accurate measurement of the ambient temperature to be
made. The measurable temperature range is −55°C to +125°C.
2. An overtemperature indicator is implemented by carrying out a
digital comparison of the ADC code for Channel 0 (temperature
sensor) with the contents of the on-chip overtemperature
register. The overtemperature indicator pin goes logic low
when a predetermined temperature is exceeded.
The on-chip temperature sensor of the AD7817/AD7818 can
be accessed via Channel 0. When Channel 0 is selected and a
conversion is initiated, the resulting ADC code at the end of the
conversion gives a measurement of the ambient temperature with a
resolution of 0.25°C. See the Temperature Measurement section.
The AD7817/AD7818 have a flexible serial interface that allows
easy interfacing to most microcontrollers. The interface is
compatible with the Intel 8051, Motorola SPI and QSPI, and
National Semiconductors MICROWIRE protocols. For more
3. The automatic power-down feature enables the AD7817 and
AD7818 to achieve superior power performance at slower
throughput rates, that is, 40 µW at 1 kSPS throughput rate.
Rev. D
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Technical Support
©2012 Analog Devices, Inc. All rights reserved.
www.analog.com
AD7817/AD7818
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Converter Details ....................................................................... 12
Typical Connection Diagram ................................................... 12
Analog Inputs.............................................................................. 12
On-Chip Reference .................................................................... 13
ADC Transfer Function............................................................. 13
Temperature Measurement....................................................... 14
Temperature Measurement Error Due to Reference Error... 14
Self-Heating Considerations..................................................... 14
Operating Modes........................................................................ 15
Power vs. Throughput................................................................ 17
AD7817 Serial Interface............................................................. 17
AD7818 Serial Interface Mode................................................. 18
Outline Dimensions....................................................................... 19
Ordering Guide .......................................................................... 20
Applications....................................................................................... 1
Functional Block Diagrams............................................................. 1
General Description ......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Timing Characteristics ................................................................ 6
Absolute Maximum Ratings............................................................ 7
ESD Caution.................................................................................. 7
Pin Configurations and Function Descriptions ........................... 8
Terminology .................................................................................... 10
Control Byte .................................................................................... 11
Circuit Information.................................................................... 12
REVISION HISTORY
10/12—Rev. C to Rev. D
9/04—Rev. B to Rev. C
Deleted AD7816..................................................................Universal
Changes to Format .............................................................Universal
Deleted Figure 15; Renumbered Sequentially............................. 14
Updated Outline Dimensions....................................................... 19
Changes to Ordering Guide .......................................................... 20
Changes to Ordering Guide.............................................................6
Changes to Operating Modes Section and Figure 16 ................ 13
Changes to Figure 17...................................................................... 14
Changes to AD7817 Serial Interface, Read Operation Section
and Figure 20................................................................................... 15
Changes to Figure 21...................................................................... 16
Rev. D | Page 2 of 20
Data Sheet
AD7817/AD7818
SPECIFICATIONS
VDD = 2.7 V to 5.5 V, GND = 0 V, REFIN = 2.5 V, unless otherwise noted. The AD7817 temperature sensor is specified with an external
2.5 V reference, and the AD7818 temperature sensor is specified with an on-chip reference. For VDD = 2.7 V, TA = 85°C maximum and
temperature sensor measurement error = 3°C.
Table 1.
Parameter
A Version1 B Version1 S Version1 Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE (AD7817 ONLY )
Sample rate = 100 kSPS, any channel,
fIN = 20 kHz
Signal-to-(Noise + Distortion) Ratio2
Total Harmonic Distortion2
Peak Harmonic or Spurious Noise2
Intermodulation Distortion2
Second-Order Terms
58
–65
–65
58
−65
−65
58
−65
−65
dB min
dB max
dB max
−75 dB typical
−75 dB typical
fa =19.9 kHz, fb = 20.1 kHz
–67
–67
–80
−67
−67
−80
−67
−67
−80
dB typ
dB typ
dB typ
Third-Order Terms
Channel-to-Channel Isolation2
DC ACCURACY (AD7817 ONLY )
Resolution
fIN = 20 kHz
Any channel
10
10
10
10
10
10
Bits
Minimum Resolution for Which No
Missing Codes are Guaranteed
Relative Accuracy2
Differential Nonlinearity2
Gain Error2
1
1
2
10
1/2
2
1/2
1
1
2
10
1/2
2
1/2
1
1
2
LSB max
LSB max
LSB max
LSB max
LSB max
LSB max
LSB max
External reference
Internal reference
+20/−10
1/2
2
Gain Error Match2
Offset Error2
Offset Error Match
1/2
TEMPERATURE SENSOR (AD7817 ONLY )
Measurement Error
Ambient Temperature 25°C
TMIN to TMAX
Measurement Error
External reference VREF = 2.5 V
On-chip reference
2
3
1
2
2
3
°C max
°C max
Ambient Temperature 25°C
TMIN to TMAX
Temperature Resolution
REFERENCE INPUT (AD7817 ONLY )3, 4
REFIN Input Voltage Range3
2.25
3
1/4
2.25
3
1/4
2.25
6
1/4
°C max
°C max
°C/LSB
2.625
2.375
40
2.625
2.375
40
2.625
2.375
40
V max
V min
kΩ min
pF max
2.5 V + 5%
2.5 V − 5%
Input Impedance
Input Capacitance
10
10
10
ON-CHIP REFERENCE (AD7817 ONLY ) 5
Temperature Coefficient3
CONVERSION RATE (AD7817 ONLY )
Track-and-Hold Acquisition Time4
Conversion Time
Nominal 2.5 V
80
80
150
400
ppm/°C typ
ns max
400
400
Source Impedance < 10 Ω
Temperature Sensor
Channel 1 to Channel 4
27
9
27
9
27
9
µs max
μs max
Rev. D | Page 3 of 20
AD7817/AD7818
Data Sheet
Parameter
A Version1 B Version1 S Version1 Unit
Test Conditions/Comments
POWER REQUIREMENTS (AD7817 ONLY )
VDD
5.5
2.7
5.5
2.7
5.5
2.7
V max
V min
For specified performance
IDD
Logic inputs = 0 V or VDD
1.6 mA typical
2.5 V external reference connected
5.5 µA typical
2 µA typical
VDD = 3 V
See the Power vs. Throughput
section for description of power
dissipation in auto power-down mode
Normal Operation
2
2
2
mA max
mA max
µA max
µA max
Using External Reference
Power-Down (VDD = 5 V)
Power-Down (VDD = 3 V)
Auto Power-Down Mode
10 SPS Throughput Rate
1 kSPS Throughput Rate
10 kSPS Throughput Rate
Power-Down
1.75
10
4
1.75
10
4
1.75
12.5
4.5
6.4
6.4
6.4
µW typ
µW typ
µW typ
µW max
48.8
434
12
48.8
434
12
48.8
434
13.5
Typically 6 µW
DYNAMIC PERFORMANCE (AD7818 ONLY ) 6
Sample rate = 100 kSPS, any channel,
fIN = 20 kHz
Signal-to-(Noise + Distortion) Ratio2
Total Harmonic Distortion2
Peak Harmonic or Spurious Noise2
Intermodulation Distortion2
Second-Order Terms
57
–65
–67
dB min
dB max
dB typ
−75 dB typical
−75 dB typical
fa = 19.9 kHz, fb = 20.1 kHz
–67
–67
–80
dB typ
dB typ
dB typ
Third-Order Terms
Channel-to-Channel Isolation2
DC ACCURACY (AD7818 ONLY )6
Resolution
fIN = 20 kHz
Any channel
10
10
Bits
Bits
Minimum Resolution for Which No
Missing Codes are Guaranteed
Relative Accuracy2
Differential Nonlinearity2
Gain Error2
1
1
10
4
LSB max
LSB max
LSB max
LSB max
Offset Error2
TEMPERATURE SENSOR (AD7818 ONLY )6
Measurement Error
Ambient Temperature 25°C
TMIN to TMAX
External reference VREF = 2.5 V
On-chip reference
2
3
°C max
°C max
Measurement Error
Ambient Temperature 25°C
TMIN to TMAX
2
3
1/4
°C max
°C max
°C/LSB
Temperature Resolution
ON-CHIP REFERENCE (AD7818 ONLY )5
Temperature Coefficient3
CONVERSION RATE (AD7818 ONLY )6
Track-and-Hold Acquisition Time4
Conversion Time
Nominal 2.5 V
30
ppm/°C typ
ns max
400
Source impedance < 10 Ω
Temperature Sensor
Channel 1
27
9
µs max
µs max
Rev. D | Page 4 of 20
Data Sheet
AD7817/AD7818
Parameter
A Version1 B Version1 S Version1 Unit
Test Conditions/Comments
POWER REQUIREMENTS (AD7818 ONLY )6
VDD
5.5
2.7
V max
V min
For specified performance
IDD
Logic inputs = 0 V or VDD
1.3 mA typical
2.5 V external reference connected
6 µA typ
2 µA typ
VDD = 3 V
See the Power vs Throughput section
for description of power dissipation
in auto power-down mode
Normal Operation
2
mA max
mA max
µA max
µA max
Using External Reference
Power-Down (VDD = 5 V)
Power-Down (VDD = 3 V)
Auto Power-Down Mode
10 SPS Throughput Rate
1 kSPS Throughput Rate
10 kSPS Throughput Rate
Power-Down
1.75
10.75
4.5
6.4
µW typ
µW typ
µW typ
µW max
48.8
434
13.5
Typically 6 µW
ANALOG INPUTS (AD7817/AD7818)7
Input Voltage Range
VREF
0
VREF
0
VREF
0
V max
V min
Input Leakage
Input Capacitance
1
10
1
10
1
10
µA min
pF max
LOGIC INPUTS (AD7817/AD7818)4
Input High Voltage, VINH
Input Low Voltage, VINL
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN
LOGIC OUTPUTS (AD7817/AD7818)4
Output High Voltage, VOH
2.4
0.8
2
0.4
3
2.4
0.8
2
0.4
3
2.4
0.8
2
0.4
3
V min
V max
V min
V max
µA max
pF max
VDD = 5 V 10%
VDD = 5 V 10%
VDD = 3 V 10%
VDD = 3 V 10%
Typically 10 nA, VIN = 0 V to VDD
10
10
10
ISOURCE = 200 µA
VDD = 5 V 10%
VDD = 3 V 10%
ISINK = 200 µA
4
2.4
4
2.4
4
2.4
V min
V min
Output Low Voltage, VOL
0.4
0.2
1
0.4
0.2
1
0.4
0.2
1
V max
V max
µA max
pF max
VDD = 5 V 10%
VDD = 3 V 10%
High Impedance Leakage Current
High Impedance Capacitance
15
15
15
1 The B Version and the S Version only apply to the AD7817. The A Version applies to the AD7817 or the AD7818 (as stated in specification).
2 See Terminology.
3 The accuracy of the temperature sensor is affected by reference tolerance. The relationship between the two is explained in the Temperature Measurement Error Due
to Reference Error section.
4 Sample tested during initial release and after any redesign or process change that may affect this parameter.
5 On-chip reference shuts down when external reference is applied.
6 These specifications are typical for AD7818 at temperatures above 85°C and with VDD greater than 3.6 V.
7 This refers to the input current when the part is not converting. Primarily due to the reverse leakage current in the ESD protection diodes.
Rev. D | Page 5 of 20
AD7817/AD7818
Data Sheet
TIMING CHARACTERISTICS
VDD = 2.7 V to 5.5 V, GND = 0 V, REFIN = 2.5 V. All specifications TMIN to TMAX, unless otherwise noted. Sample tested during initial
release and after any redesign or process changes that may affect the parameters. All input signals are measured with tr = tf = 1 ns (10% to
90% of 5 V) and timed from a voltage level of 1.6 V. See Figure 17, Figure 18, Figure 21, and Figure 22.
Table 2.
Parameter
A Version/B Version
Unit
Test Conditions/Comments
tPOWER-UP
2
µs max
µs max
µs max
ns min
ns max
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns max
ns max
ns max
ns max
ns max
ns min
ns min
Power-up time from rising edge of CONVST
Conversion time Channel 1 to Channel 4
Conversion time temperature sensor
CONVST pulse width
t1a
t1b
t2
9
27
20
50
0
t3
CONVST falling edge to BUSY rising edge
CS falling edge to RD/WR falling edge setup time
RD/WR falling edge to SCLK falling edge setup
DIN setup time before SCLK rising edge
DIN hold time after SCLK rising edge
t4
t5
0
t6
t7
t8
t9
10
10
40
40
0
SCLK low pulse width
SCLK high pulse width
t10
t11
CS falling edge to RD/WR rising edge setup time
RD/WR rising edge to SCLK falling edge setup time
DOUT access time after RD/WR rising edge
DOUT access time after SCLK falling edge
DOUT bus relinquish time after falling edge of RD/WR
DOUT bus relinquish time after rising edge of CS
BUSY falling edge to OTI falling edge
RD/WR rising edge to OTI rising edge
SCLK rising edge to CONVST falling edge (acquisition time of T/H)
0
1
t12
1
20
20
30
30
150
40
400
t13
1, 2
t14a
1, 2
t14b
t15
t16
t17
1 These figures are measured with the load circuit of Figure 3. They are defined as the time required for DOUT to cross 0.8 V or 2.4 V for VDD = 5 V 10% and 0.4 V or 2 V for
VDD = 3 V 10%, as shown in Table 1.
2 These times are derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 3. The measured number is then
extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the timing characteristics are the true bus
relinquish times of the part and as such are independent of the external bus loading capacitances.
200µA
I
OL
TO OUTPUT
PIN
1.6V
C
L
50pF
200µA
I
OL
Figure 3. Load Circuit for Access Time and Bus Relinquish Time
Rev. D | Page 6 of 20
Data Sheet
AD7817/AD7818
ABSOLUTE MAXIMUM RATINGS
TA = 25°C unless otherwise noted.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 3.
Parameter
Rating
VDD to AGND
VDD to DGND
−0.3 V to +7 V
−0.3 V to +7 V
Analog Input Voltage to AGND
VIN1 to VIN4
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3V
–0.3 V to VDD + 0.3 V
–0.3 V to VDD + 0.3 V
−65°C to +150°C
150°C
Reference Input Voltage to AGND1
Digital Input Voltage to DGND
Digital Output Voltage to DGND
Storage Temperature Range
Junction Temperature
ESD CAUTION
16-Lead TSSOP, Power Dissipation
θJA Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
450 mW
120°C/W
260°C
215°C
Infrared (15 sec)
220°C
16-Lead SOIC Package, Power Dissipation
θJA Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
450 mW
100°C/W
215°C
Infrared (15 sec)
220°C
8-Lead SOIC Package, Power Dissipation
θJA Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
450 mW
157°C/W
215°C
Infrared (15 sec)
220°C
8-Lead MSOP Package, Power Dissipation
θJA Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
450 mW
206°C/W
215°C
220°C
Infrared (15 sec)
1 If the reference input voltage is likely to exceed VDD by more than 0.3 V (that
is, during power-up) and the reference is capable of supplying 30 mA or more, it
is recommended to use a clamping diode between the REFIN pin and VDD pin.
Connect the diode as shown in this figure.
Rev. D | Page 7 of 20
AD7817/AD7818
Data Sheet
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
CONVST
BUSY
OTI
RD/WR
SCLK
D
D
IN
AD7817
TOP VIEW
CS
OUT
(Not to Scale)
AGND
DGND
REF
V
V
V
IN
IN1
IN2
DD
IN4
IN3
V
V
Figure 4. AD7817 Pin Configuration
Table 4. AD7817 Pin Function Descriptions
Pin
No. Mnemonic Description
1
CONVST
Logic Input Signal. The convert start signal. A 10-bit analog-to-digital conversion is initiated on the falling edge of this
signal. The falling edge of this signal places track-and-hold in hold mode. Track-and-hold goes into track mode again at
the end of the conversion. The state of the CONVST signal is checked at the end of a conversion. If it is logic low, the
AD7817 powers down. See the Operating Modes section.
2
3
BUSY
OTI
Logic Output. The busy signal is logic high during a temperature or voltage A/D conversion. The signal can be used to
interrupt a microcontroller when a conversion has finished.
Logic Output. The overtemperature indicator (OTI) is set logic low if the result of a conversion on Channel 0
(temperature sensor) is greater that an 8-bit word in the overtemperature register (OTR). The signal is reset at the end
of a serial read operation, that is, a rising RD/WR edge when CS is low.
4
CS
Logic Input Signal. The chip select signal is used to enable the serial port of the AD7817. This is necessary if the AD7817
is sharing the serial bus with more than one device.
5
6
AGND
REFIN
Analog Ground. Ground reference for track-and-hold comparator and capacitor DAC.
Analog Input. An external 2.5 V reference can be connected to the AD7817 at this pin. To enable the on-chip reference,
tie the REFIN pin to AGND. If an external reference is connected to the AD7817, the internal reference shuts down.
7
to
10
VIN1 to VIN4
Analog Input Channels. The AD7817 has four analog input channels. The input channels are single-ended with respect
to AGND (analog ground). The input channels can convert voltage signals in the range 0 V to VREF. A channel is selected
by writing to the address register of the AD7817. See the Control Byte section.
11
12
13
VDD
DGND
DOUT
Positive Supply Voltage, 2.7 V to 5.5 V.
Digital Ground. Ground reference for digital circuitry.
Logic Output with a High Impedance State. Data is clocked out of the AD7817 serial port at this pin. This output goes
into a high impedance state on the falling edge of RD/WR or on the rising edge of the CS signal, whichever occurs first.
14
15
DIN
SCLK
Logic Input. Data is clocked into the AD7817 at this pin.
Clock Input for the Serial Port. The serial clock is used to clock data into and out of the AD7817. Data is clocked out on
the falling edge and clocked in on the rising edge.
16
RD/WR
Logic Input Signal. The read/write signal is used to indicate to the AD7817 whether the data transfer operation is a read
or a write. Set the RD/WR logic high for a read operation and logic low for a write operation.
Rev. D | Page 8 of 20
Data Sheet
AD7817/AD7818
CONVST
OTI
1
2
3
4
8
7
6
5
RD/WR
SCLK
AD7818
TOP VIEW
GND
D
(Not to Scale)
IN/OUT
V
V
DD
IN
Figure 5. AD7818 Pin Configuration
Table 5. AD7818 Pin Function Descriptions
Pin
No. Mnemonic Description
1
CONVST
Logic Input Signal. The convert start signal initiates a 10-bit analog-to-digital conversion on the falling edge of this
signal. The falling edge of this signal places track-and-hold in hold mode. Track-and-hold goes into track mode again at
the end of the conversion. The state of the CONVST signal is checked at the end of a conversion. If it is logic low, the
AD7818 powers down. See the Operating Modes section.
2
OTI
Logic Output. The overtemperature indicator (OTI) is set logic low if the result of a conversion on Channel 0
(temperature sensor) is greater that an 8-bit word in the overtemperature register (OTR). The signal is reset at the end
of a serial read operation, that is, a rising RD/WR edge.
3
4
GND
VIN
Analog and Digital Ground.
Analog Input Channel. The input channel is single-ended with respect to GND. The input channel can convert voltage
signals in the range 0 V to 2.5 V. The input channel is selected by writing to the address register of the AD7818. See the
Control Byte section.
5
6
7
VDD
DIN/OUT
SCLK
Positive Supply Voltage, 2.7 V to 5.5 V.
Logic Input and Output. Serial data is clocked in and out of the AD7818 at this pin.
Clock Input for the Serial Port. The serial clock is used to clock data into and out of the AD7818. Data is clocked out on
the falling edge and clocked in on the rising edge.
8
RD/WR
Logic Input. The read/write signal is used to indicate to the AD7818 whether the next data transfer operation is a read
or a write. Set the RD/WR logic high for a read operation and logic low for a write.
Rev. D | Page 9 of 20
AD7817/AD7818
TERMINOLOGY
Data Sheet
specified separately. The calculation of the intermodulation
Signal-to-(Noise + Distortion) Ratio
distortion is as per the THD specification where it is the ratio
of the rms sum of the individual distortion products to the rms
amplitude of the fundamental expressed in dBs.
This is the measured ratio of signal-to-(noise + distortion) at
the output of the A/D converter. The signal is the rms amplitude of
the fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (fS/2), excluding dc.
The ratio is dependent upon the number of quantization levels
in the digitization process; the more levels, the smaller the
quantization noise. The theoretical signal-to-(noise + distortion)
ratio for an ideal N-bit converter with a sine wave input is given by:
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of crosstalk
between channels. It is measured by applying a full-scale 20 kHz
sine wave signal to one input channel and determining how much
that signal is attenuated in each of the other channels. The figure
given is the worst case across all four channels.
Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB
Relative Accuracy
Thus, for a 10-bit converter, this is 62 dB.
Relative accuracy or endpoint nonlinearity is the maximum
deviation from a straight line passing through the endpoints
of the ADC transfer function.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the fundamental.
For the AD7817/AD7818, it is defined as:
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
V22 +V32 +V42 +V52 +V6
2
THD
where:
(dB) = 20log
V1
Gain Error
This is the deviation of the last code transition (1111 . . . 110) to
(1111 . . . 111) from the ideal, that is, VREF – 1 LSB, after the
offset error has been adjusted out.
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
Gain Error Match
This is the difference in gain error between any two channels.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of
the fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum; however,
for parts where the harmonics are buried in the noise floor, it is
a noise peak.
Offset Error
This is the deviation of the first code transition (0000 . . . 000) to
(0000 . . . 001) from the ideal, that is, AGND + 1 LSB.
Offset Error Match
This is the difference in offset error between any two channels.
Track-and-Hold Acquisition Time
Intermodulation Distortion
The track-and-hold acquisition time is the time required for the
output of the track-and-hold amplifier to reach its final value,
within 1/2 LSB, after the end of conversion (the point at which
the track-and-hold returns to track mode). It also applies to
situations where a change in the selected input channel takes
place or where there is a step input change on the input voltage
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion products
at sum and difference frequencies of mfa nfb, where m, n = 0,
1, 2, 3, etc. Intermodulation terms are those for which neither m
nor n are equal to zero. For example, the second-order terms
include (fa + fb) and (fa − fb), while the third-order terms
include (2fa + fb), (2fa − fb), (fa + 2fb), and (fa − 2fb).
applied to the selected V
IN input of the AD7817 or the AD7818.
It means that the user must wait for the duration of the track-
and-hold acquisition time after the end of conversion or after a
channel change/step input change to VIN before starting another
conversion, to ensure that the part operates to specification.
The AD7817/AD7818 are tested using the CCIF standard where
two input frequencies near the top end of the input bandwidth
are used. In this case, the second- and third-order terms are of
different significance. The second-order terms are usually
distanced in frequency from the original sine waves, while the
third-order terms are usually at a frequency close to the input
frequencies. As a result, the second- and third-order terms are
Rev. D | Page 10 of 20
Data Sheet
AD7817/AD7818
CONTROL BYTE
The AD7817/AD7818 contain two on-chip registers, the address
register and the overtemperature register. These registers can be
accessed by carrying out an 8-bit serial write operation to the devices.
The 8-bit word or control byte written to the AD7817/AD7818 is
transferred to one of the two on-chip registers as follows.
Overtemperature Register
If any of the five MSBs of the control byte are logic one, the entire
eight bits of the control byte are transferred to the overtemperature
register (see Figure 6). At the end of a temperature conversion,
a digital comparison is carried out between the 8 MSBs of the
temperature conversion result (10 bits) and the contents of the
overtemperature register (8 bits). If the result of the temperature
conversion is greater than the contents of the overtemperature
Address Register
If the five MSBs of the control byte are logic zero, the three LSBs
of the control byte are transferred to the address register (see
Figure 6). The address register is a 3-bit-wide register used to
select the analog input channel on which to carry out a conversion.
It is also used to select the temperature sensor, which has the 000
address. Table 6 shows the channel selection. The internal reference
selection connects the input of the ADC to a band gap reference.
When this selection is made and a conversion is initiated, the ADC
output must be approximately midscale. After power-up, the
default channel selection is DB2 = DB1 = DB0 = 0 (temperature
sensor).
OTI
register (OTR), the overtemperature indicator ( ) goes logic
low. The resolution of the OTR is 1°C. The lowest temperature
that can be written to the OTR is −95°C and the highest is
+152°C (see Figure 7). However, the usable temperature range of
the temperature sensor is −55°C to +125°C. Figure 7 shows the
OTR and how to set TALARM (the temperature at which the
goes low).
OTI
OTR (Dec) = TALARM (°C) + 103°C
For example, to set TALARM to 50°C, OTR = 50 + 103 = 153 Dec
or 10011001 bin. If the result of a temperature conversion exceeds
Table 6. Channel Selection
OTI
OTI
50°C,
goes logic low. The
logic output is reset high at the
DB2
DB1
DB0
Channel Selection
Temperature sensor
Channel 1
Device
All
All
end of a serial read operation or if a new temperature measurement
is lower than TALARM. The default power on TALARM is 50°C.
0
0
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
DB2
DB1
DB0 ADDRESS REGISTER
Channel 2
Channel 3
Channel 4
Internal reference (1.23 V)
AD7817
AD7817
AD7817
All
IF ANY BIT DB7 TO DB3 ARE LOGIC 0
THEN DB2 TO DB0 ARE WRITTEN TO
THE ADDRESS REGISTER
MSB
DB7
LSB
DB6
DB5
DB4
DB3
DB2
DB1
DB0 CONTROL BYTE
IF ANY BIT DB7 TO DB3 IS SET TO A
LOGIC 1, THEN THE FULL 8 BITS OF THE
CONTROL WORD ARE WRITTEN TO THE
OVERTEMPERATURE REGISTER
OVERTEMPERATURE
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
REGISTER (OTR)
Figure 6. Address and Overtemperature Register Selection
OVERTEMPERATURE REGISTER
MSB
DB7
LSB
DB0
DB6
DB5
DB4
DB3
DB2
DB1
0
1
0
1
0
1
0
1
1
1
0
1
0
1
0
1
MINIMUM TEMPERATURE = –95°C
MAXIMUM TEMPERATURE = +152°C
OVERTEMPERATURE REGISTER (DEC) = T
+ 103°C
ALARM
T
RESOLUTION = 18/LSB
ALARM
Figure 7. The Overtemperature Register (OTR)
Rev. D | Page 11 of 20
AD7817/AD7818
Data Sheet
CIRCUIT INFORMATION
TYPICAL CONNECTION DIAGRAM
The AD7817/AD7818 are single- and four-channel, 9 µs
conversion time, 10-bit ADCs with an on-chip temperature
sensor, reference, and serial interface logic functions on a single
chip. The ADC section consists of a conventional, successive
approximation converter based around a capacitor DAC. The
AD7817/AD7818 are capable of running on a 2.7 V to 5.5 V power
Figure 8 shows a typical connection diagram for the AD7817.
The AGND and DGND are connected together at the device for
good noise suppression. The BUSY line is used to interrupt the
microcontroller at the end of the conversion process, and the
serial interface is implemented using three wires (see the AD7817
Serial Interface section for more details). An external 2.5 V
reference can be connected at the REFIN pin. If an external reference
is used, connect a 10 µF capacitor between REFIN and AGND.
For applications where power consumption is a concern, use the
automatic power-down at the end of a conversion to improve
power performance. See the Power vs. Throughput section.
supply, and they accept an analog input range of 0 V to VREF
.
The on-chip temperature sensor allows an accurate measurement
of the ambient device temperature to be made. The working
measurement range of the temperature sensor is −55°C to +125°C.
The AD7817/AD7818 require a 2.5 V reference, which can be
provided from their internal reference or from an external
reference source. The on-chip reference is selected by connecting
the REFIN pin to analog ground.
SUPPLY
2.7V TO 5.5V
3-WIRE
10µF
0.1µF
SERIAL
INTERFACE
V
DD
SCLK
CONVERTER DETAILS
A
A
IN1
RD/WR
0V TO 2.5V
INPUT
IN2
D
CONVST
OUT
Conversion is initiated by pulsing the
input. The
A
A
IN3
IN4
D
IN
conversion clock for the part is internally generated; therefore,
an external clock is not required, except when reading from and
writing to the serial port. The on-chip, track-and-hold goes from
track mode to hold mode, and the conversion sequence is started
AD7817
CONVST
AGND
DGND
BUSY
OTI
REF
CS
IN
CONVST
on the falling edge of the
signal. At this point, the BUSY
OPTIONAL
AD780/
REF-192
10µF
EXTERNAL
signal goes high and low again 9 µs or 27 µs later (depending on
whether an analog input or the temperature sensor is selected)
to indicate the end of the conversion process. A microcontroller
can use this signal to determine when the result of the conversion
should be read. The track-and-hold acquisition time of the
AD7817/AD7818 is 400 ns.
EXTERNAL
REFERENCE
REFERENCE
Figure 8. Typical Connection Diagram
ANALOG INPUTS
Analog Input
Figure 9 shows an equivalent circuit of the analog input structure of
the AD7817/AD7818. The two diodes, D1 and D2, provide ESD
protection for the analog inputs. Take care to ensure that the
analog input signal never exceeds the supply rails by more than
200 mV. This causes these diodes to become forward-biased
and start conducting current into the substrate. The maximum
current these diodes can conduct without causing irreversible
damage to the part is 20 mA. The C2 capacitor in Figure 9 is
typically about 4 pF and can mostly be attributed to pin
capacitance. The R1 resistor is a lumped component made up
of the on resistance of a multiplexer and a switch. This resistor
is typically about 1 kΩ. The C1 capacitor is the ADC sampling
capacitor and has a capacitance of 3 pF.
A temperature measurement is made by selecting the Channel 0
of the on-chip mux and carrying out a conversion on this channel.
A conversion on Channel 0 takes 27 µs to complete. Temperature
measurement is explained in the Temperature Measurement
section.
The on-chip reference is not available, however, REFIN can be
overdriven by an external reference source (2.5 V only). The effect
of reference tolerances on temperature measurements is discussed
in the Temperature Measurement Error Due to Reference Error
section.
Tie all unused analog inputs to a voltage within the nominal
analog input range to avoid noise pickup. For minimum power
consumption, tie the unused analog inputs to AGND.
V
DD
D1
D2
C1
3pF
R1
1kΩ
V
A
BALANCE
IN
C2
4pF
CONVERT PHASE—SWITCH OPEN
TRACK PHASE—SWITCH CLOSED
Figure 9. Equivalent Analog Input Circuit
Rev. D | Page 12 of 20
Data Sheet
AD7817/AD7818
DC Acquisition Time
ON-CHIP REFERENCE
The ADC starts a new acquisition phase at the end of a conversion
The AD7817/AD7818 have an on-chip, 1.2 V band gap reference
that is gained up to give an output of 2.5 V. By connecting the
REFIN pin to analog ground, the on-chip reference is selected.
This selection causes SW1 to open and the reference amplifier
to power up during a conversion (see Figure 11). Therefore, the
on-chip reference is not available externally. An external 2.5 V
reference can be connected to the REFIN pin, which has the
effect of shutting down the on-chip reference circuitry and
reducing IDD by approximately 0.25 mA.
CONVST
and ends on the falling edge of the
signal. At the end
of a conversion, a settling time is associated with the sampling
circuit. This settling time lasts approximately 100 ns. The
analog signal on VIN is also being acquired during this settling
time. Therefore, the minimum acquisition time needed is
approximately 100 ns.
Figure 10 shows the equivalent charging circuit for the sampling
capacitor when the ADC is in its acquisition phase. R2 represents
the source impedance of a buffer amplifier or resistive network,
R1 is an internal multiplexer resistance, and C1 is the sampling
capacitor.
EXTERNAL
REFERENCE
DETECT
REF
IN
1.2V
R1
1kΩ
SW1
V
IN
R2
1.2V
C1
3pF
26kΩ
24kΩ
BUFFER
2.5V
Figure 10. Equivalent Sampling Circuit
During the acquisition phase, the sampling capacitor must be
charged to within a 1/2 LSB of its final value. The time it takes
to charge the sampling capacitor (TCHARGE) is given by
Figure 11. On-Chip Reference
ADC TRANSFER FUNCTION
T
CHARGE = 7.6 × (R2 + 1 kΩ) × 3 pF
The output coding of the AD7817/AD7818 is straight binary. The
designed code transitions occur at successive integer LSB values
(that is, 1 LSB, 2 LSBs, and so on). The LSB size is = 2.5 V/1024 =
2.44 mV. The ideal transfer characteristic is shown in Figure 12.
For small values of source impedance, the settling time associated
with the sampling circuit (100 ns) is, in effect, the acquisition
time of the ADC. For example, with a source impedance (R2) of
10 Ω, the charge time for the sampling capacitor is approximately
23 ns. The charge time becomes significant for source impedances
of 1 kΩ and greater.
111...111
111...110
AC Acquisition Time
In ac applications, it is recommended to always buffer analog
input signals. The source impedance of the drive circuitry must
be kept as low as possible to minimize the acquisition time of
the ADC. Large values of source impedance cause the THD to
degrade at high throughput rates.
111...000
1LSB = 2.5/1024
2.44mV
011...111
000...010
000...001
000...000
1LSB
+2.5V × 1LSB
0V
ANALOG INPUT
Figure 12. ADC Transfer Function
Rev. D | Page 13 of 20
AD7817/AD7818
Data Sheet
As can be seen from the expression, a reference error produces a
gain error. This means that the temperature measurement error
due to reference error will be greater at higher temperatures. For
example, with a reference error of −1%, the measurement error
at −55°C is 2.2 LSBs (+0.5°C) and 16 LSBs (+4°C) at +125°C.
TEMPERATURE MEASUREMENT
The on-chip temperature sensor can be accessed via multiplexer
Channel 0, that is, by writing 0 0 0 to the channel address register.
The temperature is also the power on default selection. The
transfer characteristic of the temperature sensor is shown in
Figure 13. The result of the 10-bit conversion on Channel 0
can be converted to degrees centigrade by the following:
SELF-HEATING CONSIDERATIONS
The AD7817/AD7818 have an analog-to-digital conversion
function capable of a throughput rate of 100 kSPS. At this
throughput rate, the AD7817/AD7818 consume between 4 mW
and 6.5 mW of power. Because a thermal impedance is associated
with the IC package, the temperature of the die rises as a result
of this power dissipation. Figure 14 to Figure 16 show the self-
heating effect in a 16-lead SOIC. Figure 14 and Figure 15 show
the self-heating effect on a two-layer and four-layer PCB. The
plots were generated by assembling a heater (resistor) and
temperature sensor (diode) in the package being evaluated. In
Figure 14, the heater (6 mW) is turned off after 30 sec. The PCB
has little influence on the self-heating over the first few seconds
after the heater is turned on. This can be more clearly seen in
Figure 15 where the heater is switched off after 2 sec. Figure 16
shows the relative effects of self-heating in air, fluid, and
thermal contact with a large heat sink.
T
AMB = −103°C + (ADC Code/4)
+125°C
–55°C
192Dec
912Dec
ADC CODE
Figure 13. Temperature Sensor Transfer Characteristics
For example, if the result of a conversion on Channel 0 was
1000000000 (512 Dec), the ambient temperature is equal to
−103°C + (512/4) = +25°C.
0.50
2-LAYER PCB
Table 7 shows some ADC codes for various temperatures.
0.45
0.40
0.35
0.30
0.25
Table 7. Temperature Sensor Output
ADC Code
Temperature
00 1100 0000
01 0011 1000
01 1001 1100
10 0000 0000
10 0111 1000
11 1001 0000
−55°C
−25°C
0°C
+25°C
+55°C
+125°C
0.20
4-LAYER PCB
0.15
0.10
0.05
0
TEMPERATURE MEASUREMENT ERROR DUE TO
REFERENCE ERROR
–0.05
0
10
20
30
40
50
60
TIME (Seconds)
The AD7817/AD7818 are trimmed using a precision 2.5 V
reference to give the transfer function previously described. To
show the effect of the reference tolerance on a temperature reading,
the temperature sensor transfer function can be rewritten as a
function of the reference voltage and the temperature.
Figure 14. Self-Heating Effect 2-Layer and 4-Layer PCB with the Heater
(6 mW) Turned Off After 30 sec
0.25
0.20
0.15
CODE (DEC) = ([113.3285 × K × T]/[q × VREF] − 0.6646) × 1024
where:
K = Boltzmann’s Constant, 1.38 × 10−23
q = charge on an electron, 1.6 × 10−19
T = temperature (K)
0.10
2-LAYER PCB
4-LAYER PCB
0.05
So, for example, to calculate the ADC code at 25°C,
CODE = ([113.3285 × 298 × 1.38 × 10−23]/[1.6 × 10−19 × 2.5]
0
− 0.6646) × 1024
–0.05
= 511.5 (200 Hex)
0
1
2
3
4
5
TIME (Seconds)
Figure 15. Self-Heating Effect 2-Layer and 4-Layer PCB with the Heater
Switched Off After 2 sec
Rev. D | Page 14 of 20
Data Sheet
AD7817/AD7818
Figure 16 represents the worst-case effects of self-heating. The
heater delivered 6 mW to the interior of the package in all cases.
This power level is equivalent to the ADC continuously converting
at 100 kSPS. The effects of the self-heating can be reduced at
lower ADC throughput rates by operating in Mode 2 (see
Operating Modes section). When operating in this mode, the
on-chip power dissipation reduces dramatically and, as a
consequence, the self-heating effects.
OPERATING MODES
The AD7817/AD7818 have two possible modes of operation
depending on the state of the
conversion.
CONVST
pulse at the end of a
Mode 1
CONVST
In this mode of operation, the
pulse is brought high
before the end of a conversion, that is, before BUSY goes low
(see Figure 17). When operating in this mode, do not initiate a
new conversion until 100 ns after the end of a serial read operation.
This quiet time is to allow the track-and-hold to accurately acquire
the input signal after a serial read.
0.8
0.7
0.6
AIR
0.5
Mode 2
0.4
In this mode of operation, AD7817/AD7818 automatically power
down at the end of a conversion (see Figure 18). The
FLUID
0.3
CONVST
is
brought low to initiate a conversion and is left logic low until after
the end of the conversion. At this point, that is, when BUSY goes
low, the devices power down.
0.2
HEAT SINK
0.1
0
The devices are powered up again on the rising edge of the
–0.1
CONVST
signal. Superior power performance can be achieved in
0
2
4
6
8
10
12
14
16
this mode of operation by powering up the AD7817/AD7818 only
TIME (Seconds)
to carry out a conversion (see the Power vs. Throughput section).
Figure 16. Self-Heating Effect in Air, Fluid, and Thermal Contact with a Heat Sink
CS
In Figure 18, the
line is applicable to the AD7817 only.
Rev. D | Page 15 of 20
AD7817/AD7818
Data Sheet
t1
t2
CONVST
BUSY
t3
t17
CS
t15
t16
OTI
RD/WR
SCLK
D
DB7 – DB0
IN
DB7(DB9) – DB0
D
OUT
Figure 17. Mode 1 Operation
tPOWER-UP
t1
CONVST
BUSY
t3
CS
t15
OTI
t16
RD/WR
SCLK
D
IN
DB7 – DB0
D
OUT
DB7(DB9) – DB0
Figure 18. Mode 2 Operation
Rev. D | Page 16 of 20
Data Sheet
AD7817/AD7818
10
POWER vs. THROUGHPUT
Superior power performance can be achieved by using the
automatic power-down (Mode 2) at the end of a conversion
(see the Operating Modes section).
1
tPOWER-UP tCONVERT
2µs
8µs
CONVST
BUSY
0.1
0.01
tCYCLE
100µs @ 10kSPS
Figure 19. Automatic Power-Down
0
10
20
30
40
50
60
70
80
THROUGHPUT (kHz)
Figure 19 shows how the automatic power-down is implemented to
achieve the optimum power performance from the AD7817 and
AD7818. The devices operate in Mode 2, and the duration of
Figure 20. Power vs. Throughput Rate
AD7817 SERIAL INTERFACE
CONVST
pulse is set equal to the power-up time (2 µs). As the
The serial interface on the AD7817 is a 5-wire interface that has
read and write capabilities, with data being read from the output
register via the DOUT line and data being written to the control
register via the DIN line. The AD7817 operates in slave mode
and requires an externally applied serial clock to the SCLK input
to access data from the data register or write to the control byte.
throughput rate of the device is reduced, the device remains in
its power-down state longer, and the average power consumption
over time drops accordingly.
For example, if the AD7817 operates in continuous sampling
mode with a throughput rate of 10 kSPS, the power consumption
is calculated as follows. The power dissipation during normal
operation is 4.8 mW, VDD = 3 V. If the power-up time is 2 µs,
and the conversion time is 9 µs, the AD7817 can typically dissipate
4.8 mW for 11 µs (worst case) during each conversion cycle. If
the throughput rate is 10 kSPS, the cycle time is 100 µs, and
the power dissipated while powered up during each cycle is
(11/100) × (4.8 mW) = 528 µW typical. Power dissipated while
powered down during each cycle is (89/100) × (3 V × 2 µA) =
5.34 µW typ. Overall power dissipated is 528 µW + 5.34 µW =
533 µW.
WR
The RD/
line is used to determine whether data is being
written to or read from the AD7817. When data is being written
WR
to the AD7817, the RD/
line is set logic low, and when data
WR
is being read from the part, the RD/
line is set logic high
(see Figure 21). The serial interface on the AD7817 is designed
to allow the part to be interfaced to systems that provide a serial
clock that is synchronized to the serial data, such as the 80C51,
87C51, 68HC11, 68HC05, and PIC16Cxx microcontrollers.
CS
t4
t10
RD/WR
t8
7
t11
t5
SCLK
1
2
3
8
1
2
3
9
10
t6
t9
t7
DB1
D
DB5
DB0
DB7
DB6
IN
t14b
t12
t13
CONTROL BYTE
t14a
D
DB0
OUT
DB9
DB8
DB7
DB1
Figure 21. AD7817 Serial Interface Timing Diagram
Rev. D | Page 17 of 20
AD7817/AD7818
Data Sheet
Read Operation
AD7818 SERIAL INTERFACE MODE
Figure 21 shows the timing diagram for a serial read from the
The serial interface on the AD7818 is a 3-wire interface that has
read and write capabilities. Data is read from the output register
and the control byte is written to the AD7818 via the DIN/DOUT
line. The AD7818 operates in slave mode and requires an externally
applied serial clock to the SCLK input to access data from the
CS
AD7817.
WR
is brought low to enable the serial interface, and
is set logic high to indicate that the data transfer is a
WR
RD/
serial read from the AD7817. The rising edge of RD/
clocks
out the first data bit (DB9), subsequent bits are clocked out on
the falling edge of SCLK (except for the first falling SCLK edge)
and are valid on the rising edge. During a read operation, 10 bits of
data are transferred. However, a choice is available to only clock
eight bits if the full 10 bits of the conversion result are not required.
The serial data can be accessed in a number of bytes if 10 bits of
WR
data register or write to the control byte. The RD/
line is
used to determine whether data is being written to or read from
the AD7818. When data is being written to the AD7818, the
WR
RD/
line is set logic low, and when data is being read from
the AD7818 the line is set logic high (see Figure 22). The serial
interface on AD7818 is designed to allow the AD7818 to interface
with systems that provide a serial clock that is synchronized to
the serial data, such as the 80C51, 87C51, 68HC11, 68HC05,
and PIC16Cxx microcontrollers.
WR
data are being read. However, RD/
must remain high for the
duration of the data transfer operation. Before starting a new data
WR
read operation, the RD/
again. At the end of the read operation, the DOUT line enters a high
CS
signal must be brought low and high
impedance state on the rising edge of the , or the falling edge of
WR
Read Operation
RD/
, whichever occurs first. The readback process is a
Figure 22 shows the timing diagram for a serial read from the
destructive process, in that once data is read back, it is erased. A
conversion must be done again; otherwise, no data is read back.
WR
AD7818. The RD/
is set logic high to indicate that the data
WR
transfer is a serial read from the devices. When RD/
is logic
Write Operation
high, the DIN/DOUT pin becomes a logic output, and the first data
bit (DB9) appears on the pin. Subsequent bits are clocked out on
the falling edge of SCLK, starting with the second SCLK falling
Figure 21 also shows the control byte write operation to the
WR
AD7817. The RD/
input goes low to indicate to the part that
WR
edge after RD/
goes high, and are valid on the rising edge of
a serial write is about to occur. The AD7817 control byte is loaded
on the rising edge of the first eight clock cycles of the serial clock
with data on all subsequent clock cycles being ignored. To carry
SCLK. Ten bits of data are transferred during a read operation.
However, a choice is available to only clock eight bits if the full
10 bits of the conversion result are not required. The serial data
can be accessed in a number of bytes if 10 bits of data are being
WR
out a second successive write operation, the RD/
brought high and low again.
signal must be
WR
read. However, RD/
must remain high for the duration of the
Simplifying the Serial Interface
data transfer operation. To carry out a successive read operation,
WR
To minimize the number of interconnect lines to the AD7817,
CS
the RD/
pin must be brought logic low and high again. At
connect the
line to DGND. This is possible if the AD7817 is
the end of the read operation, the DIN/DOUT pin becomes a logic
not sharing the serial bus with another device. It is also possible to
tie the DIN and DOUT lines together. This arrangement is compatible
with the 8051 microcontroller. The 68HC11, 68HC05, and
PIC16Cxx can be configured to operate with a single serial data
line. In this way, the number of lines required to operate the serial
WR
input on the falling edge of RD/
.
Write Operation
A control byte write operation to the AD7818 is also shown in
WR
Figure 22. The RD/
input goes low to indicate to the part that a
WR
serial write is about to occur. The AD7818 control bytes are
loaded on the rising edge of the first eight clock cycles of the serial
clock with data on all subsequent clock cycles being ignored. To
interface can be reduced to three, that is, RD/
DIN/DOUT (see Figure 8).
, SCLK, and
WR
carry out a successive write to the AD7818 the RD/
be brought logic high and low again.
pin must
RD/WR
t5
t8
t11
1
2
3
SCLK
IN/OUT
7
8
1
2
3
9
10
t6
t9
t12
t13
t14a
t7
D
DB1
DB0
DB5
CONTROL BYTE
DB7
DB6
DB9
DB8
DB7
DB1
DB0
Figure 22. AD7818 Serial Interface Timing Diagram
Rev. D | Page 18 of 20
Data Sheet
AD7817/AD7818
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
8
1
5
4
6.20 (0.2441)
5.80 (0.2284)
4.00 (0.1574)
3.80 (0.1497)
0.50 (0.0196)
0.25 (0.0099)
1.27 (0.0500)
BSC
45°
1.75 (0.0688)
1.35 (0.0532)
0.25 (0.0098)
0.10 (0.0040)
8°
0°
0.51 (0.0201)
0.31 (0.0122)
COPLANARITY
0.10
1.27 (0.0500)
0.40 (0.0157)
0.25 (0.0098)
0.17 (0.0067)
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 23. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
10.00 (0.3937)
9.80 (0.3858)
9
8
16
1
6.20 (0.2441)
5.80 (0.2283)
4.00 (0.1575)
3.80 (0.1496)
1.27 (0.0500)
0.50 (0.0197)
0.25 (0.0098)
45°
BSC
1.75 (0.0689)
1.35 (0.0531)
0.25 (0.0098)
0.10 (0.0039)
8°
0°
COPLANARITY
0.10
SEATING
PLANE
1.27 (0.0500)
0.40 (0.0157)
0.51 (0.0201)
0.31 (0.0122)
0.25 (0.0098)
0.17 (0.0067)
COMPLIANT TO JEDEC STANDARDS MS-012-AC
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 24. 16-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-16)
Dimensions shown in millimeters and (inches)
3.20
3.00
2.80
8
1
5
4
5.15
4.90
4.65
3.20
3.00
2.80
PIN 1
IDENTIFIER
0.65 BSC
0.95
0.85
0.75
15° MAX
1.10 MAX
0.80
0.55
0.40
0.15
0.05
0.23
0.09
6°
0°
0.40
0.25
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 25.8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
Rev. D | Page 19 of 20
AD7817/AD7818
Data Sheet
5.10
5.00
4.90
16
9
8
4.50
4.40
4.30
6.40
BSC
1
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.75
0.60
0.45
8°
0°
0.30
0.19
0.65
BSC
SEATING
PLANE
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 26. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Temperature Error at 25°C
Package Description
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead MSOP
Package Option
Branding
AD7817ARZ
2°C
2°C
2°C
2°C
2°C
2°C
2°C
2°C
2°C
2°C
2°C
2°C
1°C
1°C
1°C
1°C
1°C
2°C
2°C
2°C
2°C
2°C
2°C
2°C
2°C
2°C
2°C
2°C
R-16
R-16
R-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
R-16
AD7817ARZ-REEL
AD7817ARZ-REEL7
AD7817ARU
AD7817ARU-REEL
AD7817ARU-REEL7
AD7817ARUZ
AD7817ARUZ-REEL
AD7817ARUZ-REEL7 −40°C to +85°C
AD7817BRZ
AD7817BRZ-REEL
AD7817BRZ-REEL7
AD7817BRU
AD7817BRU-REEL7
AD7817BRUZ
AD7817BRUZ-REEL
AD7817BRUZ-REEL7 −40°C to +85°C
AD7817SR
AD7817SR-REEL
AD7817SR-REEL7
AD7818ARZ
AD7818ARZ-REEL7
AD7818ARM
AD7818ARM-REEL
AD7818ARM-REEL7
AD7818ARMZ
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
R-16
R-16
RU-16
RU-16
RU-16
RU-16
RU-16
R-16
R-16
R-16
R-8
R-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
C3A
C3A
C3A
T1P
T1P
T1P
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
AD7818ARMZ-REEL
AD7818ARMZ-REEL7 −40°C to +85°C
8-Lead MSOP
1 Z = RoHS Compliant Part.
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D01316-0-10/12(D)
Rev. D | Page 20 of 20
相关型号:
©2020 ICPDF网 联系我们和版权申明