AD7658BSTZ-REEL [ADI]
250 kSPS, 6-Channel,Simultaneous Sampling, Bipolar 12/14/16-Bit ADC; 250 kSPS时, 6通道,同步采样,双极性12月14日位/ 16位ADC型号: | AD7658BSTZ-REEL |
厂家: | ADI |
描述: | 250 kSPS, 6-Channel,Simultaneous Sampling, Bipolar 12/14/16-Bit ADC |
文件: | 总25页 (文件大小:311K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
250 kSPS, 6-Channel,Simultaneous
Sampling, Bipolar 12/14/16-Bit ADC
Preliminary Technical Data
AD7658/AD7657/AD7656*
FEATURES
FUNCTIONAL BLOCK DIAGRAM
6 Independent ADCs
AV
DV
CC
CC
CONVSTB
V
CONVSTC
CONVSTA
DD
True Bipolar Analog Inputs
Pin/Software Selectable Ranges:- ±10ꢀ, ±±ꢀ
Fast throughput rate: 2±0 kSPS
Specified for ꢀCC of 4.± ꢀ to ±.± ꢀ
Low power
CS
CLK
OSC
SER/PAR
CONTROL
LOGIC
V
DRIVE
REF
STBY
BUF
OUTPUT
DRIVERS
D
OUT
A
16-BIT SAR
V
V
T/H
T/H
1
160mW at 2±0 kSPS with ± ꢀ supplies
Wide input bandwidth:
SCLK
16-BIT SAR
16-BIT SAR
16-BIT SAR
16-BIT SAR
16-BIT SAR
2
3
8± dB SNR at ±0 kHz input frequency
On-chip Reference and Reference Buffers
Parallel and Serial Interface
High speed serial interface
SPI/QSPI/µWire/DSP compatible
Standby mode: ± µA max
OUTPUT
DRIVERS
D
OUT
B
BUF
V
T/H
T/H
T/H
OUTPUT
DRIVERS
D
OUT
C
V
V
4
DATA/
CONTROL
LINES
OUTPUT
DRIVERS
BUF
5
RD
iCMOSTM Process Technology
64 LQFP package
WR
V
T/H
V
6
AD7656
AGND
SS
DGND
APPLICATIONS
Figure 1.
Power Line Monitoring systems
Instrumentation and control systems
Multi-axis positioning systems
signals in the 10V range and 5V range . They contain a 2.5V
internal reference and can also accept an external reference. If a
3V external reference is applied to the VREF pin, the ADCs can
accommodate a true bipolar 12V analog input range. VDD and
VSS supplies of 12V are required for this 12V input range.
GENERAL DESCRIPTION
The AD7658/AD7657/AD7656 contain six 12/14/16-bit, fast, low
power, successive approximation ADCs all in the one package.
The AD7658/AD7657/AD7656 core operates from a single 4.5
V to 5.5 V power supply and features throughput rates up to 250
kSPS. The parts contain low noise, wide bandwidth track-and-
hold amplifiers that can handle input frequencies up to 8 MHz.
PRODUCT HIGHLIGHTS
1. Six 12/14/16-bit 250 kSPS ADCs on board.
The conversion process and data acquisition are controlled
using CONVST signals and an internal oscillator. Three
CONVST pins allow independent simultaneous sampling of the
three ADC pairs. The AD7658/AD7657/AD7656 have both a
high speed parallel and serial interface allowing the devices to
interface with microprocessors or DSPs. When in Serial
interface mode these parts have a Daisy Chain feature allowing
multiple ADCs to connect to a single serial interface. The
AD7658/AD7657/AD7656 can accommodate true bipolar input
2. Six true bipolar high impedance analog inputs.
3. The AD7658/AD7657/AD7656 feature both a parallel and
a high speed serial interface.
* Protected by U.S. Patent No. 6,731,232
iCMOSTM Process Technology
For analog systems designers within industrial/instrumentation equipment OEMs who need high performance ICs at higher-voltage levels, iCMOS is a technology platform
that enables the development of analog ICs capable of 30V and operating at +/- 15V supplies while allowing dramatic reductions in power consumption and package size, and
increased AC and DC performance.
Rev. PrI
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Specifications subject to change without notice. No license is granted by implication
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
AD7658/AD7657/AD7656
Preliminary Technical Data
TABLE OF CONTENTS
AD7658 Specifications..................................................................... 3
ADC Transfer Function............................................................. 16
interface section.......................................................................... 17
AD7657 Specifications..................................................................... 5
AD7656 Specifications..................................................................... 7
Timing Specifications....................................................................... 9
Absolute Maximum Ratings.......................................................... 10
ESD Caution................................................................................ 10
Pin Functional Descriptions ..................................................... 11
Terminology .................................................................................... 14
converter details.......................................................................... 15
Track-and-Hold Section........................................................ 15
Analog Input Section............................................................. 15
PAR
Parallel Interface (SER/
= 0) ......................................... 17
Software Selection of ADCs.................................................. 18
H
Changing the Analog Input Range( /S SEL=0)................ 18
H
Changing the Analog Input Range( /S SEL=1)................ 19
PAR
SERIAL INTERFACE (SER/
Serial Read Operation ........................................................... 20
PAR
= 1)................................. 19
Daisy-Chain Mode(DCEN =1, SER/
= 1)................... 20
Standby/Partial Power Down Modes of Operation........... 23
Ordering Guide .......................................................................... 25
REꢀISION HISTORY
Revision PrI: Preliminary Version
Rev. PrI | Page 2 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
AD7658 SPECIFICATIONS1
Table 1. AVCC = 4.5 V to 5.5 V, VDD = 9.5 V to 16.5 V, VSS = -9.5 V to -16.5V, DVCC = 4.5 V to 5.5 V, VDRIVE = 2.7V to 5.25V, fSAMPLE
=
250 kSPS, VREF = 2.5V Internal/External, unless otherwise noted; TA = TMIN to TMAX, unless otherwise noted
Parameter
B ꢀersions1
Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE
Signal-to-Noise + Distortion (SINAD)2
fIN = 50 kHz sine wave
70
71
−92
−-TBD
dB min
dB typ
dB typ
dB typ
Total Harmonic Distortion (THD) 2
Peak Harmonic or Spurious Noise (SFDR)2
Intermodulation Distortion (IMD) 2
Second-Order Terms
Third-Order Terms
Aperture Delay
−94
−100
20
2
100
30
dB typ
dB typ
ns max
ns max
ps typ
Aperature Delay Matching
Aperture Jitter
ps typ
Full Power Bandwidth
8
2.2
MHz typ
MHz typ
@ −3 dB
@ −0.1 dB
DC ACCURACY
No Missing Codes
12
1
0.4
2.1
0.4
Bits min
LSB typ
% FS max
mV max
% FS max
Integral Nonlinearity2
Positive Full Scale Error2
Bipolar Zero Error2
Negative Full Scale Error2
ANALOG INPUT
VDD = 5.5 V
Input Voltage Ranges
4xVREF
2xVREF
0.3
V
V
RNG bit/RANGE pin = 0
RNG bit/RANGE pin = 1
DC Leakage Current
Input Capacitance
µA max
pF typ
30
REFERENCE INPUT/OUTPUT
Reference output voltage
Reference input Voltage range
DC Leakage current
2.49/2.51
V min/max
V min/max
µA max
2.5/3
0.5
20
VREF Pin
Input capacitance
pF typ
VREF Output Impedance
Reference temperature Coefficient
1
25
10
kOhms typ
ppm/°C max
ppm/°C typ
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
0.7 x VDRIVE
03 x VDRIVE
0.3
V min
V max
µA max
pF max
Typically 10 nA, VIN = 0 V or VCC
3
Input Capacitance, CIN
10
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance3
Output Coding
VDRIVE – 0.2
0.4
0.3
10
V min
ISOURCE = 200 µA;
ISINK = 200 µA
V max
µA max
pF max
Two’s Complement
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
Throughput Rate
3
400
250
µs max
ns max
kSPS
POWER REQUIREMENTS
VDD
+9.5V/+16.5V
V min/max
Rev. PrI | Page 3 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
Parameter
VSS
AVCC
B ꢀersions1
-9.5V/-16.5V
4.5/5.5
Unit
V min/max
V min/V max
Test Conditions/Comments
IDD
Digital I/PS = 0 V or VCC
SCLK on or off. VCC = 5.5 V
fSAMPLE = 250 kSPS. VCC = 5.5 V
SCLK on or off. VCC = 5.5 V
VCC = 5.5 V
Normal Mode (Static)
Normal Mode (Operational)
Full Power-Down Mode
Power Dissipation
Normal Mode (Operational)
Full Power-Down
40
35
5
mA max
mA max
µA max
192.5
16.5
mW max
µW max
fSAMPLE = 250 kSPS
1Temperature range as follows: B Version: −40°C to +85°C.
2 See terminology section.
3 Sample tested during initial release to ensure compliance.
Rev. PrI | Page 4 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
AD7657 SPECIFICATIONS1
Table 2. AVCC = 4.5 V to 5.5 V, VDD = 9.5 V to 16.5 V, VSS = -9.5 V to -16.5V, DVCC = 4.5 V to 5.5 V, VDRIVE = 2.7V to 5.25V, fSAMPLE
=
250 kSPS, VREF = 2.5V Internal/External, unless otherwise noted; TA = TMIN to TMAX, unless otherwise noted
Parameter
B ꢀersions1
Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE
Signal-to-Noise + Distortion (SINAD2
Signal-to-Noise Ratio (SNR)2
fIN = 50 kHz sine wave
81
82
83
−97
−95
dB min
dB min
dB typ
dB typ
dB typ
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise (SFDR)2
Intermodulation Distortion (IMD)2
Second-Order Terms
Third-Order Terms
Aperture Delay
−94
−100
20
2
100
30
dB typ
dB typ
ns max
ns max
ps typ
Aperature Delay Matching
Aperture Jitter
ps typ
Full Power Bandwidth
8
2.2
MHz typ
MHz typ
@ −3 dB
@ −0.1 dB
DC ACCURACY
No Missing Codes
14
Bits min
LSB typ
% FS max
mV max
% FS max
Integral Nonlinearity2
Positive Full Scale Error2
Bipolar Zero Error2
Negative Full Scale Error2
ANALOG INPUT
1.5
0.4
2.1
0.4
VDD = 5.5 V
Input Voltage Ranges
4xVREF
2xVREF
0.3
V
V
RNG bit/RANGE pin = 0
RNG bit/RANGE pin = 1
DC Leakage Current
Input Capacitance
µA max
pF typ
30
REFERENCE INPUT/OUTPUT
Reference output voltage
Reference input Voltage range
DC Leakage current
2.49/2.51
V min/max
V min/max
µA max
2.5/3
0.5
20
VREF Pin
Input capacitance
pF typ
VREF Output Impedance
Reference temperature Coefficient
1
25
10
kOhms typ
ppm/°C max
ppm/°C typ
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
0.7 x VDRIVE
0.3 x VDRIVE
0.3
V min
V max
µA max
pF max
Typically 10 nA, VIN = 0 V or VCC
3
Input Capacitance, CIN
10
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance 3
Output Coding
VDRIVE – 0.2
0.4
0.3
10
V min
ISOURCE = 200 µA;
ISINK = 200 µA
V max
µA max
pF max
Two’s Complement
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
Throughput Rate
3
500
250
µs max
ns max
kSPS
POWER REQUIREMENTS
Rev. PrI | Page 5 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
Parameter
VDD
VSS
AVCC
B ꢀersions1
+9.5V/+16.5V
-9.5V/-16.5V
4.5/5.5
Unit
Test Conditions/Comments
V min/max
V min/max
V min/V max
IDD
Digital I/PS = 0 V or VCC
SCLK on or off. VCC = 5.5 V
fSAMPLE = 250 kSPS. VCC = 5.5 V
SCLK on or off. VCC = 5.5 V
VCC = 5.5 V
Normal Mode (Static)
Normal Mode (Operational)
Full Power-Down Mode
Power Dissipation
Normal Mode (Operational)
Full Power-Down
40
35
5
mA max
mA max
µA max
192.5
16.5
mW max
µW max
fSAMPLE = 250 kSPS
1Temperature range as follows: B Version: −40°C to +85°C.
2 See Terminology Section.
3 Sample tested during initial release to ensure compliance.
Rev. PrI | Page 6 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
AD7656 SPECIFICATIONS1
Table 3. AVCC = 4.5 V to 5.5 V, VDD = 9.5 V to 16.5 V, VSS = -9.5 V to –16.5V, DVCC = 4.5 V to 5.5 V, VDRIVE = 2.7V to 5.25V, fSAMPLE
=
250 kSPS, VREF = 2.5V Internal/External, unless otherwise noted; TA = TMIN to TMAX, unless otherwise noted
Parameter
B ꢀersions1
Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE
Signal-to-Noise + Distortion (SINAD)2
fIN = 50 kHz sine wave
82.5
85
83
86
−97
−95
dB min
dB typ
dB min
dB typ
dB max
dB typ
Signal-to-Noise Ratio (SNR)2
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise (SFDR)2
Intermodulation Distortion (IMD)2
Second-Order Terms
Third-Order Terms
Aperture Delay
−94
−100
20
2
100
30
dB typ
dB typ
ns max
ns max
ps typ
Aperature Delay Matching
Aperture Jitter
ps typ
Full Power Bandwidth
8
2.2
MHz typ
MHz typ
@ −3 dB
@ −0.1 dB
DC ACCURACY
No Missing Codes
Integral Nonlinearity2
15
2
Bits min
LSB typ
4
LSB max
% FS max
mV max
% FS max
Positive Full Scale Error2
Bipolar Zero Error2
Negative Full Scale Error2
ANALOG INPUT
0.4
2.1
0.4
VDD = 5.5 V
Input Voltage Ranges
4xVREF
2xVREF
0.3
V
V
RNG bit/RANGE pin = 0
RNG bit/RANGE pin = 1
DC Leakage Current
Input Capacitance
µA max
pF typ
30
REFERENCE INPUT/OUTPUT
Reference output voltage
Reference input Voltage range
DC Leakage current
2.49/2.51
V min/max
V min/max
µA max
2.5/3
0.5
20
VREF Pin
Input capacitance
pF typ
VREF Output Impedance
Reference temperature Coefficient
1
25
10
kOhms typ
ppm/°C max
ppm/°C typ
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
0.7 x VDRIVE
0.3 x VDRIVE
0.3
V min
V max
µA max
pF max
Typically 10 nA, VIN = 0 V or VCC
3
Input Capacitance, CIN
10
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance, 3
Output Coding
VDRIVE – 0.2
0.4
0.3
10
V min
ISOURCE = 200 µA;
ISINK = 200 µA
V max
µA max
pF max
Two’s Complement
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
Throughput Rate
3
1
250
µs max
µs max
kSPS
Rev. PrI | Page 7 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
Parameter
B ꢀersions1
Unit
Test Conditions/Comments
POWER REQUIREMENTS
VDD
VSS
+9.5V/+16.5V
-9.5V/-16.5V
4.5/5.5
V min/max
V min/max
V min/V max
AVCC
IDD
Digital I/PS = 0 V or VCC
SCLK on or off. VCC = 5.5 V
fSAMPLE = 250 kSPS. VCC = 5.5 V
SCLK on or off. VCC = 5.5 V
VCC = 5.5 V
Normal Mode (Static)
Normal Mode (Operational)
Full Power-Down Mode
Power Dissipation4
Normal Mode (Operational)
Full Power-Down
40
35
5
mA max
mA max
µA max
192.5
16.5
mW max
µW max
fSAMPLE = 250 kSPS
1Temperature range as follows: B Version: −40°C to +85°C.
2 See terminology section.
3 Sample tested during initial release to ensure compliance.
V
Rev. PrI | Page 8 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
TIMING SPECIFICATIONS1
Table 4. AVCC = 4.5 V to 5.5 V, VDD = 9.5 V to 16.5 V, VSS = -9.5 V to -16.5V, VDRIVE = 2.7V to 5.25V; TA = TMIN to TMAX, unless
otherwise noted
Limit at TMIN, TMAX
Parameter ± ꢀ
Unit
Description
Parallel Mode
tCONVERT
tQUIET
t1
3
400
3
µs typ
ns min
ns min
ns typ
Conversion Time, Internal Clock
Minimum quiet time required between bus relinquish and start of next conversion
CONVST high to BUSY high
Twake-up
TBD
STBY
rising edge to CONVST rising edge
Write Operation
t13
0
ns min
ns min
ns min
ns min
ns min
CS WR
to
CS WR
to
setup time
Hold time
t14
0
t12
20
5
WR
Pulse width
Data setup time before
WR
t15
WR
rising edge
t12/14/16
5
Data hold after
rising edge
Read Operation
t2
t3
t4
t5
t6
t7
0
ns min
ns min
ns min
ns min
ns max
ns min
ns max
ns min
RD
BUSY to Delay
0
CS RD
to
setup time
Hold time
0
CS RD
to
30
30
15
25
20
RD
Pulse width
Data access time after
Bus relinquish time after
RD
falling edge
RD
rising edge
t9
Minimum time between reads
Serial Interface
fSCLK
t17
t18
t19
t20
t21
t22
t23
20
10
MHz max Frequency of Serial Read Clock
ns max
ns max
ns max
ns min
ns min
ns min
ns max
CS
to SCLK setup time
15
CS
until SDATA three-state disabled
Delay from
Data access time after SCLK rising edge
SCLK low pulse width
SCLK high pulse width
SCLK to data valid hold time
20
0.4 tSCLK
0.4 tSCLK
5
30
CS
rising edge to SDATA high impedance
200µA
I
OL
TO OUTPUT
PIN
1.6V
C
L
50pF
200µA
I
OH
Figure 2. Load Circuit for Digital Output Timing Specification
1 Sample tested during initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V.
Rev. PrI | Page 9 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
ABSOLUTE MAXIMUM RATINGS
Table 5. TA = 25°C, unless otherwise noted
Parameter
Rating
VDD to AGND, DGND
VSS to AGND, DGND
VCC to AGND, DGND
-0.3 V to +16.5 V
+0.3 V to –16.5 V
-0.3V to +7V
VDRIVE to VCC
AGND to DGND
VDRIVE to DVDD
-0.3 V to VCC + 0.3V
-0.3 V to +0.3 V
-0.3 V to DVDD + 0.3V
VSS – 0.5V to VDD + 0.5V
-0.3 V to VDRIVE +0.3 V
-0.3 V to VDRIVE +0.3V
-0.3 V to VCC +0.3V
10mA
Analog Input Voltage to AGND
Digital Input Voltage to DGND
Digital Output Voltage to GND
REFIN to AGND
Input Current to Any Pin Except Supplies2
Operating Temperature Range
Storage Temperature Range
Junction Temperature
64-LQFP Package, Power Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
Pb-free Temperature, Soldering
Reflow
-40°C to +85°C
-65°C to +150°C
+150°C
TBD°C/W
TBD°C/W
260(+0)°C
TBD kV
ESD
1Transient currents of up to 100 mA will not cause SCR latch-up.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. PrI | Page 10 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
PIN FUNCTIONAL DESCRIPTIONS
PIN 1
IDENTIFIER
1
48
47
V6
DB14/REFBUFEN/DIS
AVCC
2
DB13
46 AVCC
DB12
DB11
3
4
V5
45
AD7656
TOP VIEW
(Not to Scale)
AGND
DB10/SDATA C
5
44
AGND
6
43
DB9/SDATA B
DB8/SDATA A
7
V4
42
8
41 AVCC
DGND
VDRIVE
AVCC
9
40
V3
10
11
12
13
14
15
16
39
DB7/HBEN/DCEN
38 AGND
DB6/SCLK
DB5/DCIN A
DB4/DCIN B
DB3/DCIN C
DB2/SEL C
DB1/SEL B
37
AGND
36
V2
35
34
AVCC
AVCC
33 V1
Table 6. AD7658/AD7657/AD7656 Pin Function Descriptions
Pin Mnemonic
Description
REFCAPA, REFCAPB,
REFCAPC
Decoupling capacitors are connected to these pins to decouple the reference buffer for each
ADC pair. Each REFCAP pin should be decoupled to AGND using 10 µF and 100 nF capacitors.
V1 – V6
Analog Input1-6. These are six single-ended Analog inputs. The Analog input range on these
channels is ddetermined by the RANGE pin.
AGND
Analog Ground. Ground reference point for all analog circuitry on the
AD7658/AD7657/AD7656. All analog input signals and any external reference signal should be
referred to this AGND voltage. All eleven of these AGND pins should be connected to the
AGND plane of a system. The AGND and DGND voltages ideally should be at the same
potential and must not be more than 0.3 V apart, even on a transient basis.
DVCC
Digital Power. Normally at 5V. The DVCC and AVCC voltages should ideally be at the same
potential and must not be more than 0.3 V apart even on a transient basis. This supply should
be decoupled to DGND. 10 µF and 100 nF decoupling capacitors should be placed on the
DVCC pin.
VDRIVE
Logic power supply input. The voltage supplied at this pin determines at what voltage the
interface will operate. Nominally at the same supply as the supply of the host interface. This
pin should be decoupled to DGND. 10 µF and 100 nF decoupling capacitors should be placed
on the VDRIVE pin.
Rev. PrI | Page 11 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
DGND
Digital Ground. This is the ground reference point for all digital circuitry on the
AD7658/AD7657/AD7656. Both DGND pins should connect to the DGND plane of a system.
The DGND and AGND voltages ideally should be at the same potential and must not be more
than 0.3 V apart even on a transient basis.
AVCC
Analog Supply Voltage, 4.5 V to 5.5 V. This is the only supply voltage for ADC cores. The AVCC
and DVCC voltages ideally should be at the same potential and must not be more than 0.3 V
apart even on a transient basis. This supply should be decoupled to AGND. 10 µF and 100 nF
decoupling capacitors should be placed on the AVCC pins.
CONVSTA, B, C
Conversion Start Input A,B,C. Logic Inputs. These inputs are used to initiate conversions on the
ADC pairs. CONVSTA is used to initiate simultaneous conversions on V1 and V2. CONVSTB is
used to initiate simultameous conversions on V3 and V4. CONVSTC is used to initiate
simultaneous conversions on V5 and V6. When CONVSTX switches from low to high the track-
and-hold switch on the selected ADC pairs switches from track to hold and the conversion is
initiated.
CS
CS RD
Chip Select. Active low logic input. This input frames the data transfer. When both and
are logic low in parallel mode the output bus is enabled and the conversion result is output on
CS WR
the Parallel Data Bus lines. When both
and
are logic low in parallel mode DB[15:8] are
CS
used to write data to the on-chip control register. In serial mode the is used to frame the
serial read transfer.
RD
CS RD
Read Data. When both and
are logic low in parallel mode the output bus is enabled. In
line should be held low.
RD
serial Mode the
WR
Write Data/ reference Enable/Disable. When /S SEL pin is high both and
WR
DISABLE
H
CS
/ REF EN/
are logic low
DB[15:8] are used to write data to the internal Control Register. When /S SEL pin is low this
DISABLE
H
H
pin is used to enable or disable the internal Reference. When /S SEL =0 and REF EN/
0 the internal reference is disabled and an external reference should be applied to this pin.
DISABLE
=
H
When /S SEL = 0 and REF EN/
= 1 the internal reference is enabled.
BUSY
REFIN/REFOUT
BUSY Output. Transitions high when a conversion is started and remains high until the
conversion is complete and the conversion data is latched into the Output Data registers.
Reference Input/Output. The on-chip reference is available on this pin for use external to the
AD7658/AD7657/AD7656. Alternatively, the internal reference can be disabled and an external
reference applied to this input. See Reference Section.
PAR
SER/
Serial/parallel selection Input. When low, the parallel port is selected. When high the serial
interface mode is selected. In serial mode DB[10:8] take on their SDATA [C:A] function, DB[0:2]
take on their DOUT select function, DB[7] takes on its DCEN function. In serial mode DB15 and
DB[13:11] should be tied to DGND.
DB[0]/SEL A
DB[1]/SEL B
DB[2]/SEL C
PAR
Data Bit [0]/Select DOUT A. When SER/
= 0, this pin acts as a three-state Parallel Digital
PAR
Output pin. When SER/
is =1, this pin takes on its SEL A function, it is used to configure the
serial interface. If this pin is 1, the serial interface will operate with one/two/three DOUT ouput
pins and enables DOUT A as a serial output. When operating in serial mode this pin should
always be = 1.
PAR
Data Bit [1]/Select DOUT B. When SER/
= 0, this pin acts as a three-state Parallel Digital
PAR
Output pin. When SER/
is =1, this pin takes on its SEL B function, it is used to configure the
serial interface. If this pin is 1, the serial interface will operate with two/three DOUT ouput pins
and enables DOUT B as a serial output. If this pin is 0 the DOUT B is not enabled to operate as a
serial Data Output pin and only one DOUT output pin is used.
PAR
Data Bit [2]/Select DOUT C. When SER/
= 0, this pin acts as a three-state Parallel Digital
PAR
Output pin. When SER/
is =1, this pin takes on its SEL C function, it is used to configure the
serial interface. If this pin is 1, the serial interface will operate with three DOUT ouput pins and
enables DOUT C as a serial output. If this pin is 0 the DOUT C is not enabled to operate as a
serial Data Output pin.
DB[3]/DCIN C
DB[4]/DCIN B
DB[5]/DCIN A
DB[6]/SCLK
PAR
Data Bit [3]/Daisy Chain in C. When SER/
=0, this pin acts as a three-state Parallel Digital
is =1 and DCEN = 1, this pin acts as Daisy Chain Input C.
PAR
PAR
Output pin. When SER/
Data Bit [4]/Daisy Chain in B. When SER/
=0, this pin acts as a three-state Parallel Digital
is =1 and DCEN = 1, this pin acts as Daisy Chain Input B.
PAR
PAR
Output pin. When SER/
Data Bit [5]/Daisy Chain in A. When SER/
PAR
is low, this pin acts as a three-state Parallel Digital
is =1 and DCEN = 1, this pin acts as Daisy Chain Input A.
PAR
Output pin. When SER/
Data Bit [6[/Serial Clock. When SER/
=0, this pin acts as three-state Parallel Digital Output
Rev. PrI | Page 12 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
PAR
pin. When SER/
=1 this pin takes on its SCLK input function, obtaining the read serial clock
for the serial transfer.
Data bit 7/ High Byte Enable/ Daisy Chain Enable. When operating in Parallel Word mode
PAR
DB[7]/HBEN/DCEN
B
(SER/
= 0 and W/ = 1) this pin takes on its Data bit 7 function. When operating in Parallel
PAR
B
Byte mode (SER/
= 0 and W/ = 0), this pin takes on its HBEN function. When in this mode
and the HBEN pin is a logic high, the data will be output MSB byte first on DB[15:8]. When the
HBEN pin is a logic low the data will be output LSB byte first on DB[15:8]. When operating in
PAR
Serial mode (SER/
= 1) this pin takes on its DCEN function. When DCEN pin is a logic high
the part will operate in Daisy Chain mode with DB[5:3] taking on their DCIN[A:C] function.
DB[8]/DOUT A
DB[9]/DOUT B
PAR
Data Bit [8]/Serial Data Output A. When SER/
=0, this pin acts as a three-state Parallel
=1 and SEL A = 1, this pin takes on its DOUT A function.
PAR
PAR
Digital Output pin. When SER/
Data Bit [9]/Serial Data Output B. When SER/
PAR
=0, this pin acts as a three-state Parallel
=1 and SEL B = 1, this pin takes on its DOUT B function. This
Digital Output pin. When SER/
configures the serial interface to have two SDATA output lines.
PAR
DB[10]/DOUT C
Data Bit [10]/Serial Data Output C. When SER/
=0, this pin acts as a three-state Parallel
PAR
Digital Output pin. When SER/
configures the serial interface to have three SDATA output lines.
PAR
=1 and SEL C = 1, this pin takes on its DOUT C function. This
DB[11]/DGND
Data Bit [11]/Digital Ground. When SER/
=0, this pin acts as a three-state Parallel Digital
=1, this pin should be tied to DGND.
=0 these pins act as a three-state parallel Digital Input/Output pins.
CS WR
are low these pins are used to output the conversion result. When and
PAR
Output pin. When SER/
DB[12:13], DB[15]
PAR
Data Bit [12:15]. SER/
CS RD
When and
PAR
are low these pins are used to write to the Control Register. When SER/
should be tied to DGND.
=1 these pins
DB[14]/REFBUF
DISABLE PAR
Data Bit [14]/ REFBUF ENABLE/ . When SER/
=0, this pin acts as a three-state Digital
=1, this pin can be used to enable or disable the internal
DIS
EN/
PAR
Input/output pin. When SER/
reference buffers.
RESET
Reset Input. When set to a logic high, reset the AD7658/AD7657/AD7656. The Current
conversion if any is aborted. Internal register is set to all 0’s. If not in use, this pin could be tied
low. In Hardware mode the AD7658/AD7657/AD7656 will be configured depending on the
logic levels on the hardware select pins. When operating in software mode a reset pulse is
required afterpower up to select the default settings in the Internal register. (See Register
section)
RANGE
Analog Input Range Selection. Logic input. The polarity on this pin will determine what input
range the analog input channels will have. When this pin is a logic 1 at the falling edge of
BUSY then range for the next conversion is 2 x VREF. When this pin is a logic 0 at the falling
edge of BUSY then range for the next conversion is 4 x VREF.
VDD
VSS
Positive power supply voltage. This is the positive supply voltage for the Analog Input section.
10 µF and 100 nF decoupling capacitors should be placed on the VDD pin.
Negative power supply voltage. This is the negavtive supply voltage for the Analog Input
section. 10 µF and 100 nF decoupling capacitors should be placed on the VSS pin.
STBY
STBY
Standby mode Input. This pin is used to put all six on-chip ADCs into standby mode. The
pin is high for normal operation and low for standby operation.
H
PAR
Hardware/Software Select Input. Logic Input. When SER/
/S SEL
=0 and this pin is a logic low the
AD7658/AD7657/AD7656 operates in Hardware select mode. The ADC pairs to be
CONVST PAR
=0 this pin is a logic
simultaneously sampled are selected by the
pins. When SER/
high the ADC pairs to be simultaneously sampled are selected by writing to the control
register.
W
Word/Byte Input. When this pin is a logic low data can be transfered to and from the
AD7658/AD7657/AD7656 using the parallel data lines DB[15:0]. When this pin is a logic high
Byte mode is enabled. In this mode data is transferred using data lines DB[15:8], DB[7] takes on
its HBEN function. To obtain the 12/14/16-bit conversion result two byte reads are required.
/B
Rev. PrI | Page 13 of 25
AD7658/AD7657/AD7656
TERMINOLOGY
Preliminary Technical Data
Integral Nonlinearity
Thus, for a 12-bit converter, this is 74 dB, for a 14-bit converter,
this is 86 dB and for a 16-bit converter, this is 98 dB.
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale, a point 1/2 LSB
below the first code transition, and full scale, a point 1/2 LSB
above the last code transition.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the
fundamental. For the AD7658/AD7657/AD7656, it is defined as
2
V22 +V32 +V42 +V52 +V6
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
THD(dB) = 20log
V1
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Bipolar Zero Code Error
It is the deviation of the midscale transition (all 1s to all 0s)
from the ideal VIN voltage, i.e., AGND - 1 LSB.
Peak Harmonic or Spurious Noise
Positive Full Scale Error
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2, excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it will
be a noise peak.
It is the deviation of the last code transition (011…110) to
(011…111) from the ideal ( +4 x VREF - 1 LSB, + 2 x VREF – 1
LSB) after the bipolar Zero Code Error has been adjusted out.
Negative Full Scale Error
This is the deviation of the first code transition (10…000) to
(10…001) from the ideal (i.e., - 4 x VREF + 1 LSB, - 2 x VREF + 1
LSB) after the Bipolar Zero Code Error has been adjusted out.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa nfb where m,
n = 0, 1, 2, 3. Intermodulation distortion terms are those for which
neither m nor n are equal to zero. For example, the second-order
terms include (fa + fb) and (fa − fb), while the third-order terms
include (2fa + fb), (2fa − fb), (fa + 2fb), and (fa −2fb).
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of conversion. The track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within 1 LSB, after the end of the conversion.
See the Track-and-Hold Section for more details.
Signal-to-(Noise + Distortion) Ratio
The AD7658/AD7657/AD7656 is tested using the CCIF
standard where two input frequencies near the top end of the
input bandwidth are used. In this case, the second-order terms
are usually distanced in frequency from the original sine waves,
while the third-order terms are usually at a frequency close to
the input frequencies. As a result, the second- and third-order
terms are specified separately. The calculation of the
intermodulation distortion is as per the THD specification
where it is the ratio of the rms sum of the individual distortion
products to the rms amplitude of the sum of the fundamentals
expressed in dBs.
This is the measured ratio of signal-to-(noise + distortion) at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2, excluding dc). The ratio
depends on the number of quantization levels in the digitization
process; the more levels, the smaller the quantization noise. The
theoretical signal-to-(noise + distortion) ratio for an ideal N-bit
converter with a sine wave input is given by
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
Rev. PrI | Page 14 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
The track-and-hold amplifiers sample their respective inputs
simultaneously on the rising edge of CONVSTX. The aperture
time for the track-and-hold, (i.e. the delay time between the
external CONVSTX signal actually going into hold), is typically
20ns. This is well matched across all six track-and-holds on the
one device and also from device to device. This allows more
than six ADCs to be simultaneously sampled. The end of the
conversion is signaled by the falling edge of BUSY and its at this
point the track-and-holds return to track mode and the
acquisition time begins.
CONꢀERTER DETAILS
The AD7658/AD7657/AD7656 are high-speed, low power
converters that allow the simultaneous sampling of their six on-
chip ADCs. The Analog Inputs on the
AD7658/AD7657/AD7656 can accept True bipolar Input
signals, the RANGE pin/RNG bits are used to select between 4
x VREF or 2 x VREF as the Input Range for the next
conversion.
The AD7658/AD7657/AD7656 contain six SAR ADCs, six
track-and-hold amplifiers, on-chip 2.5V reference, reference
buffers, high speed parallel and serial interfaces. The
Analog Input Section
The AD7658/AD7657/AD7656 can handle True bipolar input
voltages. The logic level on the RANGE pin or the value written
to the RNGX bits in the Control register will determine the
Analog input Range on the AD7658/AD7657/AD7656 for the
next conversion. When the RANGE pin/ RNGX bit is 1 the
Analog input range for the next conversion is 2 x VREF, when
the RANGE pin/ RNG bit is 0 the Analog Input range for the
next conversion is 4 x VREF.
AD7658/AD7657/AD7656 allow the simultaneous sampling of
all six ADCs when all three CONVST signals are tied together.
Alternatively the six ADCs can be grouped into three pairs.
Each pair has an associated CONVST signal used to initiate
simultaneous sampling on each ADC pair, on four ADCs or all
six ADCs. CONVSTA is used to initiate simultaneous sampling
on V1 and V2, CONVSTB is used to initiate simultaneous
sampling on V3 and V4, and CONVSTC is used to initiate
simultaneous sampling on V5 and V6.
V
DD
D
R1
C2
A conversion is initiated on the AD7658/AD7657/AD7656 by
pulsing the CONVSTX input. On the rising edge of CONVSTX
the track-and-hold on the selected ADCs will be placed into
hold mode and the conversions are started. After the rising edge
of CONVSTX the BUSY signal will go high to indicate the
conversion is taking place. The conversion clock for the part is
internally generated and the conversion time for the
V1
C1
D
V
SS
Figure 3. Equivalent Analog Input Structure
AD7658/AD7657/AD7656 is 3 µs from the rising edge of
CONVSTX. The BUSY signal will return low to indicate the end
of conversion. On the falling edge of BUSY the track-and-hold
will return to track mode. Data can be read from the output
register via the parallel or serial interface.
Figure 3 shows an equivalent circuit of the analog input
structure of the AD7658/AD7657/AD7656. The two diodes, D1
and D2, provide ESD protection for the analog inputs. Care
must be taken to ensure that the analog input signal never
exceeds the VDD and VSS supply rails by more than TBD mV.
This will cause these diodes to become forward-biased and to
start conducting current into the substrate. The maximum
current these diodes can conduct without causing irreversible
damage to the part is 10 mA. Capacitor C1 in Figure 3 is
typically about 5 pF and can be attributed primarily to pin
capacitance. Resistor R1 is a lumped component made up of the
on resistance of a switch (track-and-hold switch). This resistor
is typically about 25 Ω. Capacitor C2 is the ADC sampling
capacitor and has a capacitance of 25 pF typically.
Track-and-Hold Section
The track-and-Hold amplifiers on the
AD7658/AD7657/AD7656 allow the ADCs to accurately
convert an input sine wave of full-scale amplitude to 12/14/16-
bit resolution. The input bandwidth of the track-and-hold
amplifiers is greater that the Nyquist rate of the ADC even
when the AD7658/AD7657/AD7656 is operating at its
maximum throughput rate. The AD7658/AD7657/AD7656 can
handle input frequencies up to 8 MHz.
Rev. PrI | Page 15 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
ADC TRANSFER FUNCTION
AD7658/AD7657/AD7656’s own 2.5V reference or allows for an
external reference to be connected providing the reference
source for the AD7658/AD7657/AD7656 conversions. The
AD7658/AD7657/AD7656 can accommodate a 2.5V to 3V
external reference range. When using an external reference the
internal reference needs to be disabled. After a RESET the
AD7658/AD7657/AD7656 defaults to operating in external
Reference mode. The internal reference can be enabled in either
hardware or software mode. To enable the internal reference in
The output coding of the AD7658/AD7657/AD7656 is two’s
Complement. The designed code transitions occur midway
between successive integer LSB values, i.e., 1/2 LSB, 3/2 LSBs.
The LSB size is FSR/4096 for the AD7658, FSR/16384 for the
AD7657 and FSR/65536 for the AD7656. The ideal transfer
characteristic for the AD7658/AD7657/AD7656 is shown in
Figure 4.
011...111
011...110
H
DISABLE
hardware mode, /S SEL pin =0 and the REF EN/
= 1.
H
To enable the internal reference in software mode /S SEL pin
=1, a write to the control register is necessary to make DB1 of
the register = 1. The REFIN/OUT pin should be decoupled
using 10 µF and 100 nF capacitors.
000...001
000...000
111...111
100...010
100...001
100...000
The AD7656 contains three on-chip reference buffers. Each of
the three ADC pairs has an associated reference buffer. These
reference buffers require external decoupling caps on REFCAPA,
REFCAPB, and REFCAPC pins. 10 µF and 100 nF decoupling
capacitor should be placed on these REFCAP pins.
AGND - 1LSB
-
FSR/2 +
+FSR/2 -
3/2LSB
1/2LSB
ANALOG INPUT
Figure 4. AD7658/AD7657/AD7656 Transfer Characteristic
The LSB size is dependant on the Analog Input Range selected.
See Table 7.
Reference Section
The VREF pin either provides access to the
Table 7. LSB sizes for each Analog Input Range
AD7656
10V
AD7657
10V
AD7658
Input Range
FS Range
LSB Size
5V
10V/65536
0.152 mV
5V
10V/16384
10V
20V/4096
4.88 mV
5V
10V/4096
2.44 mV
20V/65536
0.305 mV
20V/16384
1.22 mV
0.61 mV
DVCC
Digital Supply
Voltage 3V or 5V
Analog Supply
Voltage 5V
Note 1
+
100 nF +10 µF
100 nF +
10 µF
100 nF
10 µF
DGND
AGND DVCC
VDRIVE DGND
D0 to D15
+9.5V to +16.5V
Supply
AVCC
VDD
+
100 nF
100 nF
100 nF
PARALLEL
INTERFACE
10 µF
AGND
µP/µC/DSP
CONVST A/B/C
CS
REFCAPA/B/C
AGND
+
10 µF
RD
BUSY
AD7658/7/6
2.5V
REF
REFIN/OUT
AGND
+
10 µF
SER/PAR
H/S
W/B
Six Analog
Inputs
RANGE
RESET
-9.5V to -16.5V
Supply
VSS
VDRIVE
10 µF
STDBY
100 nF
Note 1: Decoupling shown on the
AVCC pin applies to each AVCC pin.
+
AGND
Figure 5. AD7658/AD7657/AD7656 Typical connection diagram.
Rev. PrI | Page 16 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
The number of read operations required will depend on the
number of ADCs that were simultaneously sampled, see Figure
5. If CONVSTA and CONVSTB were brought low
simultaneously, four read operations are required to obtain the
conversion results from V1, V2, V3 and V4. The conversion
results will be output in ascending order. For the AD7657 DB15
and DB14 will contain two leading zeros and DB[13:0] will
output the 14-bit conversion result. For the AD7658 DB[15:12]
will contain four leading zeros and DB[11:0] will output the 12-
bit conversion result.
INTERFACE SECTION
The AD7658/AD7657/AD7656 provides two interface options,
a parallel interface and a high speed serial interface. The
required interface mode is selected via the SER/
parallel interface can operate in word (W/ = 1) or byte (W/ =
0) mode. The interface modes are discussed in the following
sections.
PAR
pin. The
B
B
PAR
Parallel Interface (SER/
= 0)
The AD7658/AD7657/AD7656 consist of six 12/14/16-bit
ADCs. A simultaneous sample of all six ADCs can be
performed by connecting all three CONVST pins together,
CONVSTA, CONVSTB, CONVSTC. The rising edge of
CONVSTX initiates simultaneous conversions on the selected
ADCs. The AD7658/AD7657/AD7656 contains an on-chip
oscillator that is used to perform the conversions. The
conversion time, tCONV, is 3 µs. The BUSY signal goes low to
indicate the End of Conversion. The falling edge of the BUSY
signal is used to place the track-and-hold into track mode. The
AD7658/AD7657/AD7656 also allow the six ADCs to be
simultaneously converted in pairs by pulsing the three
CONVST pins independently. CONVSTA is used to initiate
simultaneous conversions on V1 and V2, CONVSTB is used to
initiate simultaneous conversions on V3 and V4, and
If there is only an 8-bit bus available the
AD7658/AD7657/AD7656 interface can be configured to
W
operate in BYTE mode ( /B= 1). In this configuration the
DB7/HBEN/DCEN pin takes on its HBEN function. The
conversion results from the AD7658/AD7657/AD7656 can be
accessed in two read operations with 8-bits of data provided on
DB15 to DB8 for each of the read operations, See Figure 6. The
HBEN pin determines whether the read operation accesses the
high byte or the low byte of the 12/14/16-bit conversion result
first. To always access the low byte first on DB15 to DB8, the
HBEN pin should be tied low. To always access the high byte
first on DB15 to DB8 then the HBEN pin should be tied high. In
BYTE mode when all three CONVST pins are pulsed together
to initiate simultaneous conversions on all six ADCs, twelve
read operations are necessary to read back the six 12/14/16-bit
conversion results when operating in BYTE mode. DB[6:0]
should be left unconnected in byte mode.
CONVSTC is used to initiate simultaneous conversions on V5
and V6. The conversion results from the simultaneously
sampled ADCs are stored in the output data registers.
Data can be read from the AD7658/AD7657/AD7656 via the
The AD7658/AD7657/AD7656 allow the option of reading
during a conversion. If for example, a simultaneous conversion
had occurred on V1 and V2 by pulsing the CONVSTA pin. The
processor will next read the conversion results from the
AD7658/AD7657/AD7656. During the read operation after the
BUSY signal has gone low further simultaneous conversions can
be initiated by pulsing the CONVST pins. However to achieve
the specified performance from the AD7658/AD7657/AD7656
reading after the conversion is recommended.
CS
RD
W
parallel data bus with standard
To read the data over the parallel bus SER/
CS RD
and
signals ( /B = 0).
PAR
should be tied
input signals are internally gated to enable
the conversion result onto the data bus. The data lines DB0 to
CS RD
low. The
and
DB15 leave their high impedance state when both
and
signal can be permanently tied low and
signal can be used to access the conversion results. A
CS
are logic low. The
RD
the
read operation can take place after the BUSY signal goes low.
CONVST A,B,C
t
t
ACQ
CONV
BUSY
t
4
CS
t
3
t
5
RD
t
9
t
t
2
7
t
6
t
QUIET
DATA
V2
V4
V1
V5
V3
V6
Rev. PrI | Page 17 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
W
Figure 6. AD7658/AD7657/AD7656 Parallel Interface Timing Diagram ( /B= 0)
CS
t
t
4
3
t
9
t
5
RD
t
t
7
6
DB15-DB8
LOW BYTE
HIGH BYTE
W
Figure 7. Parallel Interface – Read cycle for Byte mode of operation. ( /B= 1, HBEN = 0)
Software Selection of ADCs
Table 8.Control Register
H
The /S SEL pin determines the source of the combination of
D15 D14 D13 D12
D11
D10
D9
D8
H
ADCs that are to be simultaneously sampled. When the /S
SEL pin is a logic low the combination of channels to be
simultaneously sampled is determined by the CONVSTA,
VC VB VA RNGC RNGB RNGA REFEN REFBUF
H
CONVSTB, and CONVSTC pins. When the /S SEL pin is a
The CONVSTA signal is used to initiate a simultaneous
conversion on the combination of channels selected via the
Control register. The CONVSTB and CONVSTC signals can be
logic high the combination of channels selected for
simultaneous sampling is determined by the contents of the
Control register DB15 to DB8. In this mode a write to the
Control register is necessary.
H
tied low when operating in software mode, /S SEL = 1. The
number of read pulses required will depend on the number of
ADCs selected in the Control register and also whether
operating in word or BYTE mode. The conversion results will
be output in ascending order.
The Control register is an 8-bit write only register. Data is
CS
WR
written to this register using the
and
pins and DB[15:8]
data pins, see Figure 8. The Control register is shown in Table 8.
To select an ADC pair to be simultaneously sampled, set the
corresponding data line high during the write operation.
During the write operation the Data Bus bits DB15 to DB8 are
bidirectional and become inputs to the Control register when
RD
CS
WR
is a logic high,
and
are logic low. The logic state on
The AD7658/AD7657/AD7656 control register allows
individual ranges to be programmed on each ADC pair. DB12
to DB10 in the Control register are used to program the range
on each ADC pair. The AD7658/AD7657/AD7656 allows the
user to select either 4 x VREF or 2 x VREF as the analog
input range. RNGA is used to select the range for the next
conversion on V1 and V2, RNGB is used to select the Range for
the next conversion on V3 and V4 and RNGC is used to select
the range for V5 and V6. When the RNGX is 1 the range on the
corresponding Analog input pair is 2 x VREF. When the
RNGX bit is 0 the range on the corresponding Analog Input
pair is 4 x VREF.
DB15 through DB8 is latched into the Control register when
WR
goes logic high.
CS
WR
t
t
t
13
12
14
t
16
t
15
DATA
DB15-DB8
W
Figure 8. Parallel Interface – Write cycle for Word Mode . ( /B= 0)
The REFEN pin is used to disable the internal reference,
allowing the user to supply an external reference to the
AD7658/AD7657/AD7656. When a 0 is written to this bit the
on-chip reference is disabled. When a 1 is written to this bit the
on-chip reference is enabled.
H
Changing the Analog Input Range( /S SEL=0)
The AD7658/AD7657/AD7656 RANGE pin allows the user to
select either 2 x VREF or 4 x VREF as the analog input
H
range for the six Analog Inputs. When the /S SEL pin is low
The REF BUF bit is used to disable the internal reference
buffers. When this bit is 1 the internal reference buffers are
disabled.
the logic state of the RANGE pin is sampled on the falling edge
of the BUSY signal to determine the range for the next
simultaneous conversion. When the RANGE pin is a logic high
at the falling edge of the BUSY signal the range for the next
After a RESET occurs on the AD7658/AD7657/AD7656 the
Control register will contain all zeros.
Rev. PrI | Page 18 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
conversion is 2 x VREF. When the RANGE pin is a logic low
at the falling edge of the BUSY signal the range for the next
conversion is 4 x VREF.
transfers are used to access data from the
AD7658/AD7657/AD7656, two 16 SCLK transfers individually
CS
framed with the
signal can also be used to access the data on
the three DOUT lines. When operating the
H
Changing the Analog Input Range( /S SEL=1)
AD7658/AD7657/AD7656 in serial mode with conversion data
being clocked out on all three DOUT line DB0-DB2 should be
tied to VDRIVE. These pins are used to enable the DOUTA –
DOUTC lines respectively.
H
When the /S SEL pin is high the range can be changed by
writing to the Control Register. DB12:10 in the Control Register
are used to select the Analog input Ranges for the next
conversion. Each Analog input pair has an associated range bit,
allowing independent ranges to be programmed on each ADC
pair. When the RNGX bit is 1 the Range for the next conversion
is 2 x VREF. When the RNGX bit is 0 the range for the next
conversion is 4 x VREF.
If it is required to clock conversion data out on two data out
lines then DOUTA and DOUTB should be used. Again to
enable DOUTA and DOUTB, DB0 and DB1 should be tied to
VDRIVE and DB2 should be tied low. When six simultaneous
conversions are performed and only two DOUT lines are used,
a 48 SCLK transfer can be used to access the data from the
AD7658/AD7657/AD7656. The read sequence is shown in
Figure 10 for a simultaneous conversion on all six ADCs using
two DOUT lines. If a simultaneous conversion occurred on all
six ADCs and only two DOUT lines are used to read the results
from the AD7658/AD7657/AD7656, DOUTA will clock out the
result from V1, V2 and V5, while DOUTB will clock out the
results from V3,V4 and V6.
PAR
SERIAL INTERFACE (SER/
= 1)
By pulsing one, two or all three CONVSTX signals the
AD7658/AD7657/AD7656 will simultaneously convert the
selected channel pairs on the rising edge of CONVSTX. The
simultaneous conversions on the selected ADCs are performed
using the on-chip trimmed oscillator. After the rising edge of
CONVSTX the BUSY signal goes high to indicate the
conversion has started. It returns low when the conversion is
complete 3 µs later. The output register will be loaded with the
new conversion results and data can be read from the
AD7658/AD7657/AD7656. To read the data back from the
Data can also be clocked out using just one DOUT line, in this
case DOUTA should be used to access the conversion data. To
configure the AD7658/AD7657/AD7656 to operate in this
mode then DB0 should be tied to VDRIVE, DB1 and DB2 should
be tied low. The penalty for using just one DOUT line is the
throughput rate will be reduced. Data can be accessed from the
AD7658/AD7657/AD7656 using one 96 SCLK transfer, three 32
SCLK individually framed transfers or six 16 SCLK individually
PAR
AD7658/AD7657/AD7656 over the serial interface SER/
CS
should be tied high. The
and SCLK signal are used to
transfer data from the AD7658/AD7657/AD7656. The
AD7658/AD7657/AD7656 has three DOUT pins, DOUTA,
DOUTB, DOUTC. Data can be read back from the
AD7658/AD7657/AD7656 using one, two or all three DOUT
lines. Figure 9 shows six simultaneous conversions and the read
sequence using three DOUT lines. In figure 8, 32 SCLK
RD
framed transfers. In Serial mode the
low.
signal should be tied
CONVST A,B,C
t
CONV
t
ACQ
BUSY
CS
16
32
SCLK
t
QUIET
DOUTA
V2
V1
DOUTB
V4
V6
V3
V5
DOUTC
Figure 9. Serial Interface with three DOUT lines.
Rev. PrI | Page 19 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
CS
48
SCLK
DOUTA
DOUTB
V5
V1
V3
V2
V4
V6
Figure 10. Serial Interface with two DOUT lines.
Serial Read Operation
followed by the 14-bits of conversion data provided MSB first;
the data stream of the AD7656 consists of sixteen bits of
conversion data provided MSB first. The first bit of the
conversion result is valid on the first SCLK falling edge after the
Figure 11 shows the timing diagram for reading data from the
AD7658/AD7657/AD7656 in serial mode. The SCLK input
signal provides the clock source for the serial interface. The
signal goes low to access data from the
CS
CS
falling edge. The subsequent 15 data bits of the data are
clocked out on rising edge of the SCLK signal. Data is valid on
the SCLK falling edge. Sixteen clock pulses must be provided to
the AD7658/AD7657/AD7656 to access each conversion result.
Figure 11 shows how a 16 SCLK read is used to access the
conversion results.
CS
AD7658/AD7657/AD7656. The falling edge of
takes the bus
out of three-state and clocks out the MSB of the 12/14/16-bit
conversion result. The ADCs output 16- bits for each conversion
result. The data stream of the AD7658 consists of four leading
zeros followed by 12 bits of conversion data provided MSB first;
the data stream of the AD7657 consists of two leading zeros,
t
1
CONVST A/B/C
BUSY
t
t
ACQ
CONV
ACQUISITION
CONVERSION
ACQUISITION
CS
t
QUIET
t
17
t
21
t
20
SCLK
t
18
t
19
t
23
DB15
DB14
DB13
DB1
DB0
DOUT A/B/C
Figure 11. Serial Read Operation
configuration shows two DOUT lines being used. Simultaneous
sampling of the 12 Analog Inputs is possible by using a
common CONVST signal. The DB5, DB4 and DB3 data pins are
PAR
Daisy-Chain Mode(DCEN =1, SER/
= 1)
When reading conversion data back from the
AD7658/AD7657/AD7656 using the three/two DOUT pins it is
possible to Configure the AD7658/AD7657/AD7656 to operate
in Daisy-Chain Mode, using the DCEN pin. This Daisy-Chain
feature allows multiple AD7658/AD7657/AD7656 devices to be
cascaded together. This feature is useful for reducing
component count and wiring connections. An example
connection of two devices is shown in Figure 12, this
used as Data input pins, DCIN[A:C], for the Daisy-Chain Mode.
The rising edge of CONVST is used to initiate a conversion on
the AD7658/AD7657/AD7656. After the BUSY signal has gone
low to indicate the conversion is complete the user can begin to
read the data from the two devices. Figure 13 shows the serial
timing diagram when operating two AD7658/AD7657/AD7656
Rev. PrI | Page 20 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
devices in Daisy Chain Mode.
During the last 48 SCLKs device #2 will clock out zeros, device
#1 will shift the data it clocked in from device #2 during the
first 48 SCLKs into the digital host. This example could also
have been implemented using 3 x 32 SCLK individually framed
SCLK transfers or 6 x 16 SCLK individually framed SCLK
transfers provided DCEN remained high during the transfers.
Figure 14 shows the timing if two AD7656 were configured in
Daisy chain mode but operating with three DOUT lines. Again
assuming a simultaneous sampling of all 12 inputs occurred.
CS
The
falling edge is used to frame the serial transfer from the
AD7658/AD7657/AD7656 devices, take the bus out of three-
state and clock out the MSB of the first conversion result. In the
example shown all twelve ADC channels were simultaneously
sampled. Two DOUT line are used to read the conversion
CS
results in this example.
frames a 96 SCLK transfer. During
the first 48 SCLK the conversion data is transferred from Device
#2 to Device #1. DOUT A on device #2 transfers conversion
data from V1, V2 and V5 into DCINA in device #1. DOUT B on
device #2 transfers conversion results from V3, V4 and V6 to
DCIN B in device #1. During the first 48 SCLK device #1
transfers data into the digital host, DOUTA on device #1
transfers conversion data from V1, V2 and V5. DOUTB on
device #1 transfers conversion data from V3, V4 and V6.
CS
During the read operation the
frames a 64 SCLK transfer.
During the first 32 SCLKs of this transfer the conversion results
from Device #1 are clocked into the digital host and the
conversion results from device #2 are clocked into device #1.
During the last 32 SCLKs of the transfer the conversion results
from device #2 are clocked out of device #1 and into the digital
host. Device #2 will clock out zeros.
CONVERT
Digital Host
DATA IN1
CONVST
DOUTA
DOUTB
AD7656
SCLK CS
CONVST
DOUTA
DCINA
DCINB
DATA IN2
DOUTB
CS
AD7656
SCLK
CS
SCLK
DCEN =0
DEVICE #2
DCEN=1
DEVICE #1
Figure 12. Daisy-Chain Configuration
t
1
CONVST A/B/C
t
CONV
BUSY
CS
t
17
2
1
3
17
31
32
15
16
96
33
47
48
49
63
64
94
65
95
SCLK
t
18
t
19
LSB V1
LSB V2 MSB V5
LSB V5 MSB V1
LSB V1
LSB V3
DEVICE#1DOUTA
DEVICE#1DOUTB
MSB V1
MSB V2
MSB V2
MSB V4
LSB V5
LSB V6
LSB V3
LSB V1
LSB V3
LSB V4 MSB V6
LSB V2 MSB V5
LSB V4 MSB V6
LSB V6 MSB V3
LSB V5
MSB V3
MSB V1
MSB V3
MSB V4
MSB V2
MSB V4
DEVICE#2DOUTA
DEVICE#2DOUTB
LSB V6
Figure 13. Daisy-Chain Serial Interface Timing with 2 DOUT lines
Rev. PrI | Page 21 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
t
1
CONVST A/B/C
t
CONV
BUSY
CS
t
17
2
1
3
17
31
32
15
16
33
47
48
49
63
64
SCLK
t
18
t
19
LSB V1
LSB V3
LSB V5
LSB V2 MSB V1
LSB V4 MSB V3
LSB V6 MSB V5
LSB V1 MSB V2
LSB V3 MSB V4
LSB V5 MSB V6
LSB V2
LSB V4
LSB V6
DEVICE#1DOUTA
DEVICE#1DOUTB
DEVICE#1DOUTC
MSB V1
MSB V3
MSB V5
MSB V2
MSB V4
MSB V6
LSB V1
LSB V3
LSB V5
LSB V2
LSB V4
LSB V6
DEVICE#2DOUTA
DEVICE#2DOUTB
MSB V1
MSB V3
MSB V5
MSB V2
MSB V4
MSB V6
DEVICE#2DOUTC
Figure 14. Daisy-Chain Serial Interface Timing with 3 DOUT lines
Rev. PrI | Page 22 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
Standby/Partial Power Down Modes of Operation
STBY
logic high. The output data buffers
operation by bringing
are still operational when the AD7658/AD7657/AD7656 is in
standby. This means the user can still continue to access the
conversion results when the AD7658/AD7657/AD7656 is in
standby. This standby feature can be used to reduce the average
power consumed by the AD7658/AD7657/AD7656 when
operating at lower throughput rates. The
AD7658/AD7657/AD7656 could be placed into standby at the
end of each conversion when BUSY goes low and taken out of
standby again prior to the next conversion. The time it takes for
the AD7658/AD7657/AD7656 to come out of standby is called
the “wake-up” time. This wake-up time will limit the maximum
throughput rate at which the AD7658/AD7657/AD7656 can
operate when powering down between conversions.
Each ADC pair can be individually placed into partial power
down by bringing the CONVSTX signal low before the falling
edge of BUSY. To power the ADC pair back up again then the
CONVSTX signal should be brought high to tell the ADC pair
to power up and place the track-and-hold into track mode. In
partial power down mode the reference buffers will remain
powered up. While an ADC pair is in partial power down,
conversions can still occur on the other ADCs.
The AD7658/AD7657/AD7656 has a standby mode whereby
the device can be placed into a low current consumption mode
(0.5 µA max). The AD7658/AD7657/AD7656 is placed into
STBY
standby mode by bringing the logic input
low. The
AD7658/AD7657/AD7656 can be powered up again for normal
Rev. PrI | Page 23 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
should be avoided. Traces on different but close layers of the
board should run at right angles to each other. This will reduce
the effect of feedthrough through the board.
APPLICATION HINTS
Layout
The printed circuit board that houses the AD7656 should be
designed so the analog and digital sections are separated and
confined to certain areas of the board. This facilitates the use of
ground planes that can be easily separated. Digital and analog
ground planes should be joined in only one place, preferably
underneath the AD7656, or, at least, as close as possible to the
AD7656. If the AD7656 is in a system where multiple devices
require analog to digital ground connections, the connection
should still be made at one point only, a star ground point,
which should be established as close as possible to the AD7656.
The power supply lines to the AD7656 should use as large a
trace as possible to provide low impedance paths and reduce
the effect of glitches on the power supply lines. Good
decoupling is also important to lower the supplies impedance
presented to the AD7656 and to reduce the magnitude of the
supply spikes. Decoupling ceramic capacitors, typically 100 nF,
should be placed on all of the power supply pins, power
supplies pins VDD, VSS, AVCC, DVCC, and VDRIVE. The decoupling
capacitors should be placed close to, and ideally right up
against, these pins and their corresponding ground pins.
Additionally, low ESR 10 µF capacitors should be located in the
vicinity of the ADC to further reduce low frequency ripple.
It is recommended to avoid running digital lines under the
device as these will couple noise onto the die. The analog
ground plane should be allowed to run under the AD7656 to
avoid noise coupling. Fast switching signals like CONVST or
clocks should be shielded with digital ground to avoid radiating
noise to other sections of the board and should never run near
analog signal paths. Crossover of digital and analog signals
The decoupling capacitors should be close to the ADC and
connected with short and large traces to minimize parasitic
inductances.
Rev. PrI | Page 24 of 25
AD7658/AD7657/AD7656
Preliminary Technical Data
OUTLINE DIMENSIONS
64-Lead Low Profile Quad Flat Package [LQFP]
(ST-64)
Dimensions shown in millimeters
ORDERING GUIDE
AD76±8/AD76±7/AD76±6
Products
Temperature Package
Package Description
Package Outline
AD7658BSTZ1
AD7658BSTZ-REEL1
AD7657BSTZ1
AD7657BSTZ-REEL1
AD7656BSTZ1
AD7656BSTZ-REEL1
EVAL- AD7656CB2
EVAL-CONTROL BRD23
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
LQFP
ST-64
ST-64
ST-64
ST-64
ST-64
ST-64
LQFP
LQFP
LQFP
LQFP
LQFP
Evaluation Board
Controller Board
NOTES
1 Z = Pb-free part.
2 This can be used as a stand-alone evaluation board or in conjunction with the EVAL-CONTROL Board for evaluation/demonstration purposes.
3 This board is a complete unit allowing a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators. To order a complete
evaluation kit, the particular ADC evaluation board, e.g., EVAL-AD7658/AD7657/AD7656CB, the EVAL-CONTROL BRD2, and a 12V transformer must be ordered. See
relevant Evaluation Board Technical note for more information.
Rev. PrI | Page 25 of 25
相关型号:
AD7658YSTZ-1
6-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PQFP64, ROHS COMPLIANT, MS-026BCD, LQFP-64
ROCHESTER
AD7658YSTZ-1-RL
6-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PQFP64, ROHS COMPLIANT, MS-026BCD, LQFP-64
ROCHESTER
AD7658YSTZ-500RL7
IC 6-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQFP64, LEAD FREE, MS-026BCD, LQFP-64, Analog to Digital Converter
ADI
AD7660ACP
1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, QCC48, MO-220-VKKD-2, LFCSP-48
ROCHESTER
AD7660ACPZ
IC 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, QCC48, MO-220-VKKD-2, LFCSP-48, Analog to Digital Converter
ADI
©2020 ICPDF网 联系我们和版权申明