AD7651_17 [ADI]
16-Bit 100 kSPS PulSAR Unipolar ADC with Reference;型号: | AD7651_17 |
厂家: | ADI |
描述: | 16-Bit 100 kSPS PulSAR Unipolar ADC with Reference |
文件: | 总29页 (文件大小:615K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
16-Bit 100 kSPS PulSARTM
Unipolar ADC with Reference
AD7651
FEATURES
FUNCTIONAL BLOCK DIAGRAM
REFBUFIN
Throughput: 100 kSPS
REF REFGND
DVDD DGND
16-bit resolution
Analog input voltage range: 0 V to 2.5 V
No pipeline delay
OVDD
OGND
AGND
AVDD
AD7651
SERIAL
PORT
REF
Parallel and serial 5 V/3 V interface
16
IN
SWITCHED
CAP DAC
DATA[15:0]
BUSY
SPI®/QSPITM/MICROWIRETM/DSP compatible
Single 5 V supply operation
Power dissipation
16 mW typ, 160 µW @ 1 kSPS without REF
38 mW typ with REF
INGND
PARALLEL
INTERFACE
PDREF
PDBUF
RD
CLOCK
CS
PD
CONTROL LOGIC AND
SER/PAR
RESET
CALIBRATION CIRCUITRY
OB/2C
48-lead LQFP and 48-lead LFCSP packages
Pin-to-pin compatible with PulSAR ADCs
BYTESWAP
CNVST
02964-0-001
APPLICATIONS
Data acquisition
Figure 1. Functional Block Diagram
Table 1. PulSAR Selection
Instrumentation
800–
1000
Digital signal processing
Spectrum analysis
Medical instruments
Battery-powered systems
Process control
Type/kSPS
100–250
500–570
Pseudo-
Differential
AD7651
AD7650/AD7652 AD7653
AD7660/AD7661 AD7664/AD7666 AD7667
True Bipolar
AD7663
AD7675
AD7665
AD7676
AD7671
AD7677
True
Differential
GENERAL DESCRIPTION
18-Bit
AD7678
AD7679
AD7654
AD7655
AD7674
The AD7651 is a 16-bit, 100 kSPS, charge redistribution SAR
analog-to-digital converter that operates from a single 5 V
power supply. The part contains a high speed 16-bit sampling
ADC, an internal conversion clock, internal reference, error
correction circuits, and both serial and parallel system inter-
face ports.
Multichannel/
Simultaneous
PRODUCT HIGHLIGHTS
1. Fast Throughput.
The AD7651 is a 100 kSPS, charge redistribution, 16-bit
SAR ADC with internal error correction circuitry.
The AD7651 is fabricated using Analog Devices’ high perform-
ance, 0.6 micron CMOS process, with correspondingly low cost,
and is available in a 48-lead LQFP and a tiny 48-lead LFCSP
with operation specified from –40°C to +85°C.
2. Internal Reference.
The AD7651 has an internal reference with a typical
temperature drift of 7 ppm/°C.
3. Single-Supply Operation.
The AD7651 operates from a single 5 V supply. Its power
dissipation decreases with throughput.
4. Serial or Parallel Interface.
Versatile parallel or 2-wire serial interface arrangement is
compatible with both 3 V and 5 V logic.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2003 Analog Devices, Inc. All rights reserved.
AD7651* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
View a parametric search of comparable parts.
REFERENCE MATERIALS
Technical Articles
• MS-2210: Designing Power Supplies for High Speed ADC
EVALUATION KITS
DESIGN RESOURCES
• AD7651 Material Declaration
• PCN-PDN Information
• Quality And Reliability
• Symbols and Footprints
• AD7651 Evaluation Kit
DOCUMENTATION
Application Notes
• AN-280: Mixed Signal Circuit Technologies
• AN-282: Fundamentals of Sampled Data Systems
DISCUSSIONS
View all AD7651 EngineerZone Discussions.
• AN-311: How to Reliably Protect CMOS Circuits Against
Power Supply Overvoltaging
• AN-342: Analog Signal-Handling for High Speed and
Accuracy
SAMPLE AND BUY
Visit the product page to see pricing options.
• AN-931: Understanding PulSAR ADC Support Circuitry
• AN-932: Power Supply Sequencing
Data Sheet
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
• AD7651: 16-Bit 100 kSPS SAR Unipolar ADC with
Reference Data Sheet
Product Highlight
• 8- to 18-Bit SAR ADCs ... From the Leader in High
Performance Analog
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7651
TABLE OF CONTENTS
Specifications..................................................................................... 3
Timing Specifications....................................................................... 5
Absolute Maximum Ratings............................................................ 7
Pin Configuration and Function Descriptions............................. 8
Definitions of Specifications ......................................................... 11
Typical Performance Characteristics ........................................... 12
Circuit Information........................................................................ 15
Converter Operation.................................................................. 15
Typical Connection Diagram.................................................... 17
Power Dissipation versus Throughput .................................... 19
Conversion Control.................................................................... 19
Digital Interface .......................................................................... 20
Parallel Interface......................................................................... 20
Serial Interface ............................................................................ 20
Master Serial Interface............................................................... 21
Slave Serial Interface .................................................................. 22
Microprocessor Interfacing....................................................... 24
Application Hints............................................................................ 25
Bipolar and Wider Input Ranges .............................................. 25
Layout .......................................................................................... 25
Evaluating the AD7651’s Performance .................................... 25
Outline Dimensions ....................................................................... 26
Ordering Guide........................................................................... 26
REVISION HISTORY
Revision 0, Initial Version.
Rev. 0 | Page 2 of 28
AD7651
SPECIFICATIONS
Table 2. –40°C to +85°C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted
Parameter
Conditions
Min
Typ
Max
Unit
RESOLUTION
16
Bits
ANALOG INPUT
Voltage Range
Operating Input Voltage
VIN – VINGND
VIN
0
–0.1
VREF
+3
V
V
VINGND
–0.1
+0.5
V
Analog Input CMRR
Input Current
fIN = 10 kHz
100 kSPS Throughput
65
1.1
dB
µA
Input Impedance1
THROUGHPUT SPEED
Complete Cycle
10
µs
Throughput Rate
0
100
kSPS
DC ACCURACY
Integral Linearity Error
No Missing Codes
Differential Linearity Error
Transition Noise
Unipolar Zero Error, TMIN to TMAX
Unipolar Zero Error Temperature Drift3
Full-Scale Error, TMIN to TMAX
–6
15
–2
+6
+3
5
LSB2
Bits
LSB
LSB
0.7
3
LSB
0.25
ppm/°C
% of FSR
ppm/°C
LSB
3
REF = 2.5 V
0.12
Full-Scale Error Temperature Drift
Power Supply Sensitivity
AC ACCURACY
0.6
2
AVDD = 5 V 5%
Signal-to-Noise
Spurious Free Dynamic Range
Total Harmonic Distortion
fIN = 45 kHz
fIN = 45 kHz
fIN = 10 kHz
fIN = 45 kHz
fIN = 45 kHz
–60 dB Input, fIN = 45 kHz
86
98
–98
–98
86
dB4
dB
dB
dB
dB
dB
kHz
Signal-to-(Noise + Distortion)
30
800
–3 dB Input Bandwidth
SAMPLING DYNAMICS
Aperture Delay
Aperture Jitter
Transient Response
2
5
ns
ps rms
µs
Full-Scale Step
8.75
2.52
REFERENCE
Internal Reference Voltage
Internal Reference Temperature Drift
Line Regulation
Turn-On Settling Time
Temperature Pin
VREF @ 25°C
–40°C to +85°C
AVDD = 5 V 5%
2.48
2.5
7
24
5
V
ppm/°C
ppm/V
ms
CREF = 10 µF
Voltage Output @ 25°C
Temperature Sensitivity
Output Resistance
External Reference Voltage Range
External Reference Current Drain
300
1
4.3
2.5
35
mV
mV/°C
kΩ
V
µA
2.3
AVDD – 1.85
100 kSPS Throughput
Rev. 0 | Page 3 of 28
AD7651
Parameter
Conditions
Min
Typ
Max
Unit
DIGITAL INPUTS
Logic Levels
VIL
VIH
IIL
IIH
–0.3
2.0
–1
+0.8
DVDD + 0.3
+1
+1
V
V
µA
µA
–1
DIGITAL OUTPUTS
Data Format5
Pipeline Delay6
VOL
VOH
ISINK = 1.6 mA
ISOURCE = –500 µA
0.4
V
V
OVDD – 0.6
POWER SUPPLIES
Specified Performance
AVDD
DVDD
OVDD
4.75
4.75
2.7
5
5
5.25
5.25
5.257
V
V
V
Operating Current
100 kSPS Throughput
With Reference and Buffer
Reference and Buffer Alone
AVDD8
6.2
3
mA
mA
mA
µA
mW
µW
mW
AVDD9
DVDD10
1.5
18
16
160
38
OVDD10
Power Dissipation without REF10
100 kSPS Throughput
1 kSPS Throughput
100 kSPS Throughput
25
Power Dissipation with REF10
TEMPERATURE RANGE11
Specified Performance
45
TMIN to TMAX
–40
+85
°C
1See Analog Input section.
2LSB means least significant bit. With the 0 V to 2.5 V input range, 1 LSB is 38.15 µV.
3See Definitions of Specifications section. These specifications do not include the error contribution from the external reference.
4All specifications in dB are referred to a full-scale input FS. Tested with an input signal at 0.5 dB below full-scale, unless otherwise specified.
5Parallel or Serial 16-Bit.
6Conversion results are available immediately after completed conversion.
7 The max should be the minimum of 5.25 V and DVDD + 0.3 V.
8 With REF, PDREF and PDBUF are LOW; without REF, PDREF and PDBUF are HIGH.
9 With PDREF, PDBUF LOW and PD HIGH.
10 Tested in Parallel Reading Mode
11Consult factory for extended temperature range.
Rev. 0 | Page 4 of 28
AD7651
TIMING SPECIFICATIONS
Table 3. –40°C to +85°C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted
Parameter
Symbol Min
Typ
Max
Unit
Refer to Figure 26 and Figure 27
Convert Pulse Width
Time between Conversions
CNVST LOW to BUSY HIGH Delay
BUSY HIGH All Modes Except Master Serial Read after Convert
Aperture Delay
End of Conversion to BUSY LOW Delay
Conversion Time
Acquisition Time
t1
t2
t3
t4
t5
t6
t7
t8
t9
10
10
ns
µs
ns
µs
ns
ns
µs
µs
ns
35
1.25
2
10
1.25
8.75
10
RESET Pulse Width
Refer to Figure 28, Figure 29, and Figure 30 (Parallel Interface Modes)
CNVST LOW to DATA Valid Delay
DATA Valid to BUSY LOW Delay
Bus Access Request to DATA Valid
Bus Relinquish Time
t10
t11
t12
t13
1.25
µs
ns
ns
ns
12
5
45
15
Refer to Figure 32 and Figure 33 (Master Serial Interface Modes)1
CS LOW to SYNC Valid Delay
CS LOW to Internal SCLK Valid Delay1
CS LOW to SDOUT Delay
t14
t15
t16
t17
t18
t19
t20
t21
t22
t23
t24
t25
t26
t27
t28
t29
t30
10
10
10
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
CNVST LOW to SYNC Delay
525
SYNC Asserted to SCLK First Edge Delay
Internal SCLK Period2
3
25
12
7
4
2
40
Internal SCLK HIGH2
Internal SCLK LOW2
SDOUT Valid Setup Time2
SDOUT Valid Hold Time2
SCLK Last Edge to SYNC Delay2
3
CS HIGH to SYNC HI-Z
10
10
10
CS HIGH to Internal SCLK HI-Z
CS HIGH to SDOUT HI-Z
BUSY HIGH in Master Serial Read after Convert2
CNVST LOW to SYNC Asserted Delay
SYNC Deasserted to BUSY LOW Delay
Refer to Figure 34 and Figure 35 (Slave Serial Interface Modes)1
External SCLK Setup Time
External SCLK Active Edge to SDOUT Delay
SDIN Setup Time
SDIN Hold Time
See Table 4
1.25
25
µs
ns
t31
t32
t33
t34
t35
t36
t37
5
3
5
5
25
10
10
ns
ns
ns
ns
ns
ns
ns
18
External SCLK Period
External SCLK HIGH
External SCLK LOW
1In serial interface modes, the SYNC, SCLK, and SDOUT timings are defined with a maximum load CL of 10 pF; otherwise, the load is 60 pF maximum.
2In Serial Master Read during Convert Mode. See Table 4 for serial master read after convert mode.
Rev. 0 | Page 5 of 28
AD7651
Table 4. Serial Clock Timings in Master Read after Convert
DIVSCLK[1]
0
0
1
1
DIVSCLK[0]
Symbol
t18
t19
t19
t20
t21
t22
t23
t24
0
1
0
1
Unit
ns
ns
ns
ns
ns
ns
ns
ns
SYNC to SCLK First Edge Delay Minimum
Internal SCLK Period Minimum
Internal SCLK Period Maximum
Internal SCLK HIGH Minimum
Internal SCLK LOW Minimum
SDOUT Valid Setup Time Minimum
SDOUT Valid Hold Time Minimum
SCLK Last Edge to SYNC Delay Minimum
BUSY HIGH Width Maximum
3
17
50
70
22
21
18
4
17
100
140
50
49
18
30
130
3.5
17
25
40
12
7
4
2
200
280
100
99
18
80
3
2
55
2.5
290
5.75
t24
µs
Rev. 0 | Page 6 of 28
AD7651
ABSOLUTE MAXIMUM RATINGS
Table 5. AD7651 Stress Ratings1
I
1.6mA
OL
IN2, TEMP2,REF, REFBUFIN,
INGND, REFGND to AGND
Ground Voltage Differences
AGND, DGND, OGND
Supply Voltages
AVDD + 0.3 V to
AGND – 0.3 V
TO OUTPUT
PIN
1.4V
C
L
0.3 V
60pF*
I
500µA
OH
AVDD, DVDD, OVDD
AVDD to DVDD, AVDD to OVDD
DVDD to OVDD
–0.3 V to +7 V
7 V
–0.3 V to +7 V
–0.3 V to DVDD + 0.3 V
20 mA
*IN SERIAL INTERFACE MODES,THE SYNC, SCLK, AND
SDOUT TIMINGS ARE DEFINEDWITH A MAXIMUM LOAD
C
OF 10pF; OTHERWISE,THE LOAD IS 60pF MAXIMUM.
L
02964-0-006
Digital Inputs
PDREF, PDBUF3
Figure 2. Load Circuit for Digital Interface Timing,
SDOUT, SYNC, SCLK Outputs CL = 10 pF
Internal Power Dissipation4
Internal Power Dissipation5
Junction Temperature
Storage Temperature Range
Lead Temperature Range
(Soldering 10 sec)
700 mW
2.5 W
2V
150°C
0.8V
tDELAY
–65°C to +150°C
300°C
tDELAY
2V
2V
0.8V
0.8V
02965-0-007
1Stresses above those listed under Absolute Maximum Ratings may cause
permanent damage to the device. This is a stress rating only; functional
operation of the device at these or any other conditions above those listed
in the operational sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect
device reliability.
Figure 3. Voltage Reference Levels for Timing
2See Analog Input section.
3See Voltage Reference Input section.
4Specification is for the device in free air:
48-Lead LQFP; θJA = 91°C/W, θJC = 30°C/W
5Specification is for the device in free air:
48-Lead LFCSP; θJA = 26°C/W.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 7 of 28
AD7651
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
48
47 46 45 44 43 42 41 40 39 38 37
1
2
3
4
5
6
7
AGND
AVDD
NC
36
35
34
33
32
31
30
29
AGND
CNVST
PD
RESET
CS
PIN 1
IDENTIFIER
BYTESWAP
OB/2C
NC
NC
AD7651
RD
TOP VIEW
DGND
BUSY
D15
D14
D13
(Not to Scale)
8
9
10
11
12
SER/PAR
D0
D1
28
27
26
25
D2/DIVSCLK0
D3/DIVSCLK1
D12
13 14
15 16 17 18 19 20 21 22 23 24
NC = NO CONNECT
02965-0-002
Figure 4. 48-Lead LQFP (ST-48) and 48-Lead LFCSP (CP-48)
Table 6. Pin Function Descriptions
Pin No. Mnemonic
Type1 Description
1, 36,
AGND
P
Analog Power Ground Pin.
41, 42
2, 44
3, 6,
AVDD
NC
P
Input Analog Power Pin. Nominally 5 V.
No Connect.
7, 40
4
5
BYTESWAP
OB/2C
DI
DI
Parallel Mode Selection (8-/16-bit). When LOW, the LSB is output on D[7:0] and the MSB is output on
D[15:8]. When HIGH, the LSB is output on D[15:8] and the MSB is output on D[7:0].
Straight Binary/Binary Twos Complement. When OB/2C is HIGH, the digital output is straight binary;
when LOW, the MSB is inverted, resulting in a twos complement output from its internal shift
register.
8
SER/PAR
D[0:1]
DI
Serial/Parallel Selection Input. When LOW, the parallel port is selected; when HIGH, the serial
interface mode is selected and some bits of the DATA bus are used as a serial port.
Bit 0 and Bit 1 of the Parallel Port Data Output Bus. When SER/PAR is HIGH, these outputs are in high
impedance.
When SER/PAR is LOW, these outputs are used as Bit 2 and Bit 3 of the parallel port data output bus.
When SER/PAR is HIGH, EXT/INT is LOW, and RDC/SDIN is LOW (serial master read after convert),
these inputs, part of the serial port, are used to slow down, if desired, the internal serial clock that
clocks the data output. In other serial modes, these pins are not used.
9, 10
11, 12
DO
DI/O
D[2:3]or
DIVSCLK[0:1]
13
D4 or
EXT/INT
DI/O
When SER/PAR is LOW, this output is used as Bit 4 of the parallel port data output bus.
When SER/PAR is HIGH, this input, part of the serial port, is used as a digital select input for choosing
the internal data clock or an external data clock. With EXT/INT tied LOW, the internal clock is selected
on the SCLK output. With EXT/INT set to a logic HIGH, output data is synchronized to an external
clock signal connected to the SCLK input.
14
15
D5 or
INVSYNC
DI/O
DI/O
When SER/PAR is LOW, this output is used as Bit 5 of the parallel port data output bus.
When SER/PAR is HIGH, this input, part of the serial port, is used to select the active state of the SYNC
signal. It is active in both master and slave modes. When LOW, SYNC is active HIGH. When HIGH,
SYNC is active LOW.
When SER/PAR is LOW, this output is used as Bit 6 of the parallel port data output bus.
When SER/PAR is HIGH, this input, part of the serial port, is used to invert the SCLK signal. It is active
in both master and slave modes.
D6 or
INVSCLK
Rev. 0 | Page 8 of 28
AD7651
Pin No. Mnemonic
Type1 Description
16
D7 or
DI/O
When SER/PAR is LOW, this output is used as Bit 7 of the parallel port data output bus.
RDC/SDIN
When SER/PAR is HIGH, this input, part of the serial port, is used as either an external data input or a
read mode selection input depending on the state of EXT/INT.
When EXT/INT is HIGH, RDC/SDIN could be used as a data input to daisy-chain the conversion results
from two or more ADCs onto a single SDOUT line. The digital data level on SDIN is output on DATA
with a delay of 16 SCLK periods after the initiation of the read sequence.
When EXT/INT is LOW, RDC/SDIN is used to select the read mode. When RDC/SDIN is HIGH, the data
is output on SDOUT during conversion. When RDC/SDIN is LOW, the data can be output on SDOUT
only when the conversion is complete.
17
18
19
20
21
OGND
OVDD
DVDD
DGND
D8 or
SDOUT
P
P
P
P
Input/Output Interface Digital Power Ground.
Input/Output Interface Digital Power. Nominally at the same supply as the host interface (5 V or 3 V).
Digital Power. Nominally at 5 V.
Digital Power Ground.
DO
When SER/PAR is LOW, this output is used as Bit 8 of the parallel port data output bus.
When SER/PAR is HIGH, this output, part of the serial port, is used as a serial data output
synchronized to SCLK. Conversion results are stored in an on-chip register. The AD7651 provides the
conversion result, MSB first, from its internal shift register. The DATA format is determined by the
logic level of OB/2C. In serial mode when EXT/INT is LOW, SDOUT is valid on both edges of SCLK. In
serial mode when EXT/INT is HIGH, if INVSCLK is LOW, SDOUT is updated on the SCLK rising edge and
valid on the next falling edge; if INVSCLK is HIGH, SDOUT is updated on the SCLK falling edge and
valid on the next rising edge.
22
23
D9 or
SCLK
DI/O
DO
When SER/PAR is LOW, this output is used as Bit 9 of the parallel port data or SCLK output bus.
When SER/PAR is HIGH, this pin, part of the serial port, is used as a serial data clock input or output,
depending upon the logic state of the EXT/INT pin. The active edge where the data SDOUT is
updated depends upon the logic state of the INVSCLK pin.
D10 or
SYNC
When SER/PAR is LOW, this output is used as Bit 10 of the parallel port data output bus.
When SER/PAR is HIGH, this output, part of the serial port, is used as a digital output frame
synchronization for use with the internal data clock (EXT/INT = logic LOW). When a read sequence is
initiated and INVSYNC is LOW, SYNC is driven HIGH and remains HIGH while the SDOUT output is
valid. When a read sequence is initiated and INVSYNC is HIGH, SYNC is driven LOW and remains LOW
while the SDOUT output is valid.
24
D11 or
RDERROR
DO
When SER/PAR is LOW, this output is used as Bit 11 of the parallel port data output bus. When
SER/PAR and EXT/INT are HIGH, this output, part of the serial port, is used as an incomplete read error
flag. In slave mode, when a data read is started and not complete when the following conversion is
complete, the current data is lost and RDERROR is pulsed HIGH.
25–28
29
D[12:15]
BUSY
DO
DO
Bit 12 to Bit 15 of the Parallel Port Data Output Bus. These pins are always outputs regardless of the
state of SER/PAR.
Busy Output. Transitions HIGH when a conversion is started and remains HIGH until the conversion is
complete and the data is latched into the on-chip shift register. The falling edge of BUSY could be
used as a data ready clock signal.
30
31
32
DGND
RD
P
DI
DI
Must Be Tied to Digital Ground.
Read Data. When CS and RD are both LOW, the interface parallel or serial output bus is enabled.
CS
Chip Select. When CS and RD are both LOW, the interface parallel or serial output bus is enabled. CS
is also used to gate the external clock.
33
34
35
RESET
PD
DI
DI
DI
Reset Input. When set to a logic HIGH, this pin resets the AD7651 and the current conversion, if any,
is aborted. If not used, this pin could be tied to DGND.
Power-Down Input. When set to a logic HIGH, power consumption is reduced and conversions are
inhibited after the current one is completed.
Start Conversion. If CNVST is HIGH when the acquisition phase (t8) is complete, the next falling edge
on CNVST puts the internal sample/hold into the hold state and initiates a conversion. The mode is
most appropriate if low sampling jitter is desired. If CNVST is LOW when the acquisition phase (t8) is
complete, the internal sample/hold is put into the hold state and a conversion is immediately
started.
CNVST
37
38
39
REF
REFGND
INGND
AI/O
AI
AI
Reference Input Voltage. On-chip reference output voltage.
Reference Input Analog Ground.
Analog Input Ground.
Rev. 0 | Page 9 of 28
AD7651
Pin No. Mnemonic
Type1 Description
43
45
46
47
IN
AI
Primary Analog Input with a Range of 0 V to 2.5 V.
Temperature Sensor Voltage Output.
Reference Input Voltage. The reference output and the reference buffer input.
This pin allows the choice of internal or external voltage references. When LOW, the on-chip
reference is turned on. When HIGH, the internal reference is switched off and an external reference
must be used.
TEMP
REFBUFIN
PDREF
AO
AI/O
DI
48
PDBUF
DI
This pin allows the choice of buffering an internal or external reference with the internal buffer.
When LOW, the buffer is selected. When HIGH, the buffer is switched off.
1AI = Analog Input; AI/O = Bidirectional Analog; AO = Analog Output; DI = Digital Input; DI/O = Bidirectional Digital; DO = Digital Output; P = Power.
Rev. 0 | Page 10 of 28
AD7651
DEFINITIONS OF SPECIFICATIONS
Integral Nonlinearity Error (INL)
Total Harmonic Distortion (THD)
Linearity error refers to the deviation of each individual code
from a line drawn from negative full scale through positive full
scale. The point used as negative full scale occurs ½ LSB before
the first code transition. Positive full scale is defined as a level
1½ LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal, and is
expressed in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It
is often specified in terms of resolution for which no missing
codes are guaranteed.
Signal-to-(Noise + Distortion) Ratio (S/[N+D])
S/(N+D) is the ratio of the rms value of the actual input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/(N+D) is expressed in decibels.
Full-Scale Error
The last transition (from 011…10 to 011…11 in twos
complement coding) should occur for an analog voltage 1½ LSB
below the nominal full scale (2.49994278 V for the 0 V to 2.5 V
range). The full-scale error is the deviation of the actual level of
the last transition from the ideal level.
Aperture Delay
Aperture delay is a measure of the acquisition performance and
is measured from the falling edge of the
input to when
CNVST
the input signal is held for a conversion.
Unipolar Zero Error
Transient Response
The first transition should occur at a level ½ LSB above analog
ground (19.073 µV for the 0 V to 2.5 V range). Unipolar zero
error is the deviation of the actual transition from that point.
Transient response is the time required for the AD7651 to
achieve its rated accuracy after a full-scale step function is
applied to its input.
Spurious-Free Dynamic Range (SFDR)
Overvoltage Recovery
SFDR is the difference, in decibels (dB), between the rms
amplitude of the input signal and the peak spurious signal.
Overvoltage recovery is the time required for the ADC to
recover to full accuracy after an analog input signal 150% of the
full-scale value is reduced to 50% of the full-scale value.
Effective Number Of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to S/(N+D) by the following formula:
Reference Voltage Temperature Coefficient
Reference voltage temperature coefficient is the change of
internal reference voltage output voltage V over the operating
temperature range and normalized by the output voltage at
25°C, expressed in ppm/°C. The equation follows:
ENOB = (S/[N+D]dB – 1.76)/6.02
and is expressed in bits.
V(T2)–V(T1)
V(25°C)×(T2 –T1)
TCV(ppm/°C) =
×106
where:
V(25°C) = V at +25°C
V(T2) = V at Temperature 2 (+85°C)
V(T1) = V at Temperature 1 (–40°C)
Rev. 0 | Page 11 of 28
AD7651
TYPICAL PERFORMANCE CHARACTERISTICS
4
2.0
1.5
1.0
0.5
0
3
2
1
0
–1
–2
–3
–4
–0.5
–1.0
0
16384
32768
CODE
49152
65536
0
16384
32768
CODE
49152
65536
02964-0-026
02964-0-023
Figure 5. Integral Nonlinearity vs. Code
Figure 8. Differential Nonlinearity vs. Code
140000
120000
100000
80000
60000
40000
20000
0
180000
160000
140000
120000
100000
80000
60000
40000
20000
0
155528
114156 114686
51585
49184
20890
10822
2896
479
1903
137
0
0
0
0
0
19
5
0
7FFB 7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004
7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004
CODE IN HEX
CODE IN HEX
02964-0-027
02964-0-028
Figure 6. Histogram of 261,120 Conversions of a
DC Input at the Code Transition
Figure 9. Histogram of 261,120 Conversions of a
DC Input at the Code Center
15.5
15.0
14.5
14.0
13.5
13.0
0
–20
90
89
88
87
86
85
84
83
82
81
80
fS = 100kSPS
fIN = 45.7kHz
SNR = 86.7dB
THD = 102.5dB
SFDR = 103.6dB
S/[N+D] = 86.6dB
–40
–60
SNR
–80
–100
–120
–140
–160
S/[N+D]
ENOB
–180
0
10
20
30
40
50
1
10
100
1000
FREQUENCY (kHz)
FREQUENCY (kHz)
02964-0-029
02964-0-030
Figure 7. FFT Plot
Figure 10. SNR, S/(N+D), and ENOB vs. Frequency
Rev. 0 | Page 12 of 28
AD7651
120
110
100
90
–100
–105
–110
–115
–120
–70
–75
SFDR
–80
–85
THD
80
–90
70
–95
60
–100
–105
–110
–115
–120
SECOND
HARMONIC
THD
THIRD
50
HARMONIC
SECOND
HARMONIC
40
THIRD
HARMONIC
30
20
5
85
–55
–35
–15
25
45
65
125
105
1
10
100
1000
TEMPERATURE (°C)
FREQUENCY (kHz)
02964-0-034
02964-0-031
Figure 14. THD and Harmonics vs. Temperature
Figure 11. THD, Harmonics, and SFDR vs. Frequency
90
89
88
87
86
85
10000
1000
100
10
AVDD
DVDD
SNR
1
OVDD
S/[N+D]
0.1
0.01
0.001
PDREF = PDBUF = HIGH
10
100
1000
10000
100000
–60
–50
–40
–30
–20
–10
0
SAMPLE RATE (SPS)
INPUT LEVEL (dB)
02964-0-035
02964-0-032
Figure 12. SNR and S/(N+D) vs. Input Level (Referred to Full Scale)
Figure 15. Operating Current vs. Sample Rate
6
5
89
88
87
86
85
15.5
4
3
15.0
14.5
14.0
13.5
FULL SCALE
2
1
SNR
0
–1
–2
–3
–4
–5
–6
ZERO ERROR
S/[N+D]
–55
–35
–15
5
25
45
65
85
105
125
–55
–35
–15
5
25
45
65
85
105
125
TEMPERATURE (°C)
TEMPERATURE (dB)
02964-0-036
02964-0-033
Figure 16. Zero Error, Full Scale with Reference vs. Temperature
Figure 13. SNR, S/(N+D), and ENOB vs. Temperature
Rev. 0 | Page 13 of 28
AD7651
2.5042
2.5040
2.5038
2.5036
2.5034
2.5032
2.5030
2.5028
50
40
30
20
10
0
OVDD = 2.7V @ 85°C
OVDD = 2.7V @ 25°C
OVDD = 5V @ 85°C
OVDD = 5V @ 25°C
–40
–20
0
20
40
60
80
100
120
0
50
100
(pF)
150
200
TEMPERATURE (°C)
C
L
02964-0-037
02964-0-039
Figure 17. Typical Reference Output Voltage vs. Temperature
Figure 19. Typical Delay vs. Load Capacitance CL
25
20
15
10
5
0
–30 –26 –22 –18 –14 –10 –6 –2
2
6
10 14 18 22 26 30
REFERENCE DRIFT (ppm/°C)
02965-0-040
Figure 18. Reference Voltage Temperature Coefficient Distribution (100 Units)
Rev. 0 | Page 14 of 28
AD7651
CIRCUIT INFORMATION
IN
REF
REFGND
SWITCHES
CONTROL
SW
MSB
32,768C 16,384C
LSB
A
4C
2C
C
C
BUSY
CONTROL
COMP
LOGIC
INGND
OUTPUT
CODE
65,536C
SW
B
CNVST
02964-0-005
Figure 20. ADC Simplified Schematic
The AD7651 is a very fast, low power, single supply, precise
16-bit analog-to-digital converter (ADC).
During the acquisition phase, the common terminal of the array
tied to the comparator's positive input is connected to AGND
via SWA. All independent switches are connected to the analog
input IN. Thus, the capacitor array is used as a sampling
capacitor and acquires the analog signal on IN. Similarly, the
dummy capacitor acquires the analog signal on INGND.
The AD7651 provides the user with an on-chip track/hold,
successive approximation ADC that does not exhibit any
pipeline or latency, making it ideal for multiple multiplexed
channel applications.
When
goes LOW, a conversion phase is initiated. When
CNVST
The AD7651 can be operated from a single 5 V supply and can
be interfaced to either 5 V or 3 V digital logic. It is housed in
either a 48-lead LQFP or a 48-lead LFCSP that saves space and
allows flexible configurations as either a serial or parallel inter-
face. The AD7651 is pin-to-pin compatible with PulSAR ADCs.
the conversion phase begins, SWA and SWB are opened. The
capacitor array and dummy capacitor are then disconnected
from the inputs and connected to REFGND. Therefore, the
differential voltage between IN and INGND captured at the end
of the acquisition phase is applied to the comparator inputs,
causing the comparator to become unbalanced. By switching
each element of the capacitor array between REFGND and REF,
the comparator input varies by binary weighted voltage steps
(VREF/2, VREF/4, …VREF/65536). The control logic toggles these
switches, starting with the MSB, to bring the comparator back
into a balanced condition.
CONVERTER OPERATION
The AD7651 is a successive-approximation ADC based on a
charge redistribution DAC. Figure 20 shows a simplified sche-
matic of the ADC. The capacitive DAC consists of an array of 16
binary weighted capacitors and an additional LSB capacitor. The
comparator’s negative input is connected to a dummy capacitor
of the same value as the capacitive DAC array.
After this process is completed, the control logic generates the
ADC output code and brings the BUSY output LOW.
Rev. 0 | Page 15 of 28
AD7651
Table 7. Output Codes and Ideal Input Voltages
Digital Output Code (Hex)
Transfer Functions
2C
Using the OB/ digital input, the AD7651 offers two output
Analog
Input
2.499962 V FFFF1
2.499923 V FFFE
1.250038 V 8001
Straight
Binary
Twos
Complement
codings: straight binary and twos complement. The LSB size is
Description
FSR –1 LSB
FSR – 2 LSB
Midscale + 1 LSB
Midscale
VREF/65536, which is about 38.15 µV. The AD7651’s ideal
7FFF1
7FFE
0001
0000
FFFF
8001
80002
transfer characteristic is shown in Figure 21 and Table 7.
1 LSB =V
/65536
REF
1.25 V
8000
111...111
111...110
111...101
Midscale – 1 LSB
–FSR + 1 LSB
–FSR
1.249962 V 7FFF
38 µV
0 V
0001
00002
1This is also the code for overrange analog input (VIN – VINGND above
VREF – VREFGND).
2This is also the code for underrange analog input (VIN below VINGND).
000...010
000...001
000...000
0V
1 LSB
V
– 1 LSB
REF
– 1.5 LSB
0.5 LSB
V
REF
ANALOG INPUT
02964-0-003
Figure 21. ADC Ideal Transfer Function
ANALOG
SUPPLY
(5V)
20Ω
DIGITAL SUPPLY
(3.3V OR 5V)
+
+
+
100nF
100nF
100nF
10µF
10µF
10µF
AVDD
DGND DVDD
OVDD
OGND
AGND
SERIAL
PORT
SCLK
REF
SDOUT
4
1
C
REFBUFIN
R
100nF
µC/µP/DSP
REFGND
BUSY
AD7651
3
CNVST
D
2
U1
IN
OB/2C
ANALOG INPUT
(0VTO 2.5V)
DVDD
SER/PAR
C
C
INGND
PD
PDBUF RESET
CS
RD
BYTESWAP
PDREF
CLOCK
NOTES
1
THE CONFIGURATION SHOWN IS USING THE INTERNAL REFERENCE AND INTERNAL BUFFER.
THE AD8021 IS RECOMMENDED. SEE DRIVER AMPLIFIER CHOICE SECTION.
OPTIONAL LOW JITTER.
2
3
4
A 10µF CERAMIC CAPACITOR (X5R, 1206 SIZE) IS RECOMMENDED (e.g., PANASONIC ECJ3YB0J106M).
SEE VOLTAGE REFERENCE INPUT SECTION.
02964-0-004
Figure 22. Typical Connection Diagram
Rev. 0 | Page 16 of 28
AD7651
Driver Amplifier Choice
TYPICAL CONNECTION DIAGRAM
Figure 22 shows a typical connection diagram for the AD7651.
Analog Input
Although the AD7651 is easy to drive, the driver amplifier needs
to meet the following requirements:
Figure 23 shows an equivalent circuit of the input structure of
the AD7651.
•
The driver amplifier and the AD7651 analog input circuit
must be able to settle for a full-scale step of the capacitor
array at a 16-bit level (0.0015%). In the amplifier’s data
sheet, settling at 0.1% to 0.01% is more commonly speci-
fied. This could differ significantly from the settling time at
a 16-bit level and should be verified prior to driver
selection. The tiny op amp OP184, which combines ultra
low noise and high gain-bandwidth, meets this settling
time requirement.
The two diodes, D1 and D2, provide ESD protection for the
analog inputs IN and INGND. Care must be taken to ensure
that the analog input signal never exceeds the supply rails by
more than 0.3 V. This will cause these diodes to become
forward-biased and start conducting current. These diodes can
handle a forward-biased current of 100 mA maximum. For
instance, these conditions could eventually occur when the
input buffer’s (U1) supplies are different from AVDD. In such a
case, an input buffer with a short-circuit current limitation can
be used to protect the part.
•
•
The noise generated by the driver amplifier needs to be
kept as low as possible in order to preserve the SNR and
transition noise performance of the AD7651. The noise
coming from the driver is filtered by the AD7651 analog
input circuit 1-pole low-pass filter made by R1 and C2 or
by the external filter, if one is used.
AVDD
D1
D2
C2
R1
IN
OR INGND
C1
The driver needs to have a THD performance suitable to
that of the AD7651.
AGND
02965-0-008
The OP184, OP162 or AD8519 meet these requirements and are
usually appropriate for almost all applications. As an alternative,
in very high speed and noise-sensitive applications, the AD8021
with an external 10 pF compensation capacitor can be used.
This capacitor should have good linearity as an NPO ceramic or
mica type. Moreover, the use of a noninverting +1 gain
arrangement is recommended and helps to obtain the best
signal-to-noise ratio.
Figure 23. Equivalent Analog Input Circuit
This analog input structure allows the sampling of the
differential signal between IN and INGND. Unlike other
converters, INGND is sampled at the same time as IN. By using
this differential input, small signals common to both inputs are
rejected. For instance, by using INGND to sense a remote signal
ground, ground potential differences between the sensor and
the local ADC ground are eliminated.
The AD8022 could also be used if a dual version is needed and
gain of 1 is present. The AD829 is an alternative in applications
where high frequency (above 100 kHz) performance is not
required. In gain of 1 applications, it requires an 82 pF
compensation capacitor. The AD8610 is an option when low
bias current is needed in low frequency applications.
During the acquisition phase, the impedance of the analog input
IN can be modeled as a parallel combination of capacitor C1
and the network formed by the series connection of R1 and C2.
C1 is primarily the pin capacitance. R1 is typically 3250 Ω and is
a lumped component made up of some serial resistors and the
on resistance of the switches. C2 is typically 60 pF and is mainly
the ADC sampling capacitor. During the conversion phase,
where the switches are opened, the input impedance is limited
to C1. R1 and C2 make a 1-pole low-pass filter that reduces
undesirable aliasing effect and limits the noise.
When the source impedance of the driving circuit is low, the
AD7651 can be driven directly. Large source impedances will
significantly affect the ac performance, especially total
harmonic distortion.
Rev. 0 | Page 17 of 28
AD7651
Voltage Reference Input
The AD7651 allows the choice of either a very low temperature
drift internal voltage reference or an external 2.5 V reference.
For applications that use multiple AD7651s, it is more effective
to use the internal buffer to buffer the reference voltage.
Unlike many ADCs with internal references, the internal
reference of the AD7651 provides excellent performance and
can be used in almost all applications.
Care should be taken with the voltage reference’s temperature
coefficient, which directly affects the full-scale accuracy if this
parameter matters. For instance, a 15 ppm/°C temperature
coefficient of the reference changes full scale by 1 LSB/°C.
To use the internal reference along with the internal buffer,
PDREF and PDBUF should both be LOW. This will produce a
1.207 V voltage on REFBUFIN which, amplified by the buffer,
will result in a 2.5 V reference on the REF pin.
Note that VREF can be increased to AVDD – 1.85 V. Since the
input range is defined in terms of VREF, this would essentially
increase the range to 0 V to 3 V with an AVDD above 4.85 V.
The AD780 can be selected with a 3 V reference voltage.
The output impedance of REFBUFIN is 11 kΩ (minimum) when
the internal reference is enabled. It is useful to decouple
REFBUFIN with a 100 nF ceramic capacitor. Thus, the 100 nF
capacitor provides an RC filter for noise reduction.
The TEMP pin, which measures the temperature of the AD7651,
can be used as shown in Figure 24. The output of TEMP pin is
applied to one of the inputs of the analog switch (e.g., ADG779),
and the ADC itself is used to measure its own temperature. This
configuration is very useful for improving the calibration
accuracy over the temperature range.
To use an external reference along with the internal buffer,
PDREF should be HIGH and PDBUF should be LOW. This
powers down the internal reference and allows the 2.5 V
reference to be applied to REFBUFIN.
TEMP
ADG779
To use an external reference directly on REF pin, PDREF and
PDBUF should both be HIGH.
TEMPERATURE
SENSOR
IN
ANALOG INPUT
(UNIPOLAR)
AD7651
C
AD8021
C
PDREF and PDBUF respectively power down the internal
reference and the internal reference buffer. Note that the PDREF
and PDBUF input current should never exceed 20 mA. This
could eventually occur when input voltage is above AVDD (for
instance at power up). In this case, a 100 Ω series resistor is
recommended.
02964-0-024
Figure 24. Temperature Sensor Connection Diagram
Power Supply
The AD7651 uses three power supply pins: an analog 5 V supply
AVDD, a digital 5 V core supply DVDD, and a digital input/
output interface supply OVDD. OVDD allows direct interface
with any logic between 2.7 V and DVDD + 0.3 V. To reduce the
supplies needed, the digital core (DVDD) can be supplied
through a simple RC filter from the analog supply, as shown in
Figure 22. The AD7651 is independent of power supply
sequencing once OVDD does not exceed DVDD by more than
0.3 V, and is thus free of supply voltage induced latch-up.
The internal reference is temperature compensated to 2.5 V
20 mV. The reference is trimmed to provide a typical drift of 7
ppm/°C. This typical drift characteristic is shown in Figure 17.
For improved drift performance, an external reference such as
the AD780 can be used.
The AD7651 voltage reference input REF has a dynamic input
impedance; it should therefore be driven by a low impedance
source with efficient decoupling between the REF and REFGND
inputs. This decoupling depends on the choice of the voltage
reference but usually consists of a low ESR tantalum capacitor
connected to REF and REFGND with minimum parasitic
inductance. A 10 µF (X5R, 1206 size) ceramic chip capacitor (or
47 µF tantalum capacitor) is appropriate when using either the
internal reference or one of these recommended reference
voltages:
•
•
•
The low noise, low temperature drift ADR421 and AD780
The low power ADR291
The low cost AD1582
Rev. 0 | Page 18 of 28
AD7651
POWER DISSIPATION VERSUS THROUGHPUT
The
trace should be shielded with ground and a low
CNVST
Operating currents are very low during the acquisition phase,
allowing significant power savings when the conversion rate is
reduced (see Figure 25). The AD7651 automatically reduces its
power consumption at the end of each conversion phase. This
makes the part ideal for very low power battery applications.
The digital interface and the reference remain active even
during the acquisition phase. To reduce operating digital supply
currents even further, digital inputs need to be driven close to
the power supply rails (i.e., DVDD or DGND), and OVDD
should not exceed DVDD by more than 0.3 V.
value serial resistor (i.e., 50 Ω) termination should be added
close to the output of the component that drives this line.
For applications where SNR is critical, the
signal should
CNVST
have very low jitter. This may be achieved by using a dedicated
oscillator for generation, or to clock with a
CNVST
CNVST
high frequency, low jitter clock, as shown in Figure 22.
t2
t1
CNVST
100000
10000
1000
BUSY
t4
t3
t6
t5
MODE
ACQUIRE
CONVERT
t7
ACQUIRE
t8
CONVERT
02964-0-011
100
Figure 26. Basic Conversion Timing
t9
PDREF = PDBUF = PDHIGH
10
RESET
10
100
1k
10k
100k
SAMPLING RATE (SPS)
02964-0-038
BUSY
DATA
Figure 25. Power Dissipation vs. Sampling Rate
CONVERSION CONTROL
t8
Figure 26 shows the detailed timing diagrams of the conversion
process. The AD7651 is controlled by the signal, which
CNVST
CNVST
initiates conversion. Once initiated, it cannot be restarted or
aborted, even by the power-down input PD, until the conversion
02964-0-011
is complete.
operates independently of
and .
CNVST
CS
RD
Figure 27. RESET Timing
Conversions can be automatically initiated with the AD7651. If
CS = RD = 0
CNVST
is held LOW when BUSY is LOW, the AD7651 controls
CNVST
the acquisition phase and automatically initiates a new
conversion. By keeping LOW, the AD7651 keeps the
t1
CNVST
t10
conversion process running by itself. It should be noted that the
analog input must be settled when BUSY goes LOW. Also, at
BUSY
t4
power-up,
should be brought LOW once to initiate the
t3
CNVST
t11
conversion process. In this mode, the AD7651 can run slightly
faster than the guaranteed 100 kSPS.
DATA
BUS
PREVIOUS CONVERSION DATA
NEW DATA
02964-0-012
Although
is a digital signal, it should be designed with
CNVST
special care with fast, clean edges, and levels with minimum
overshoot and undershoot or ringing.
Figure 28. Master Parallel Data Timing for Reading (Continuous Read)
Rev. 0 | Page 19 of 28
AD7651
DIGITAL INTERFACE
CS
RD
The AD7651 has a versatile digital interface; it can be interfaced
with the host system by using either a serial or a parallel
interface. The serial interface is multiplexed on the parallel data
bus. The AD7651 digital interface also accommodates both 3 V
and 5 V logic by simply connecting the OVDD supply pin of the
AD7651 to the host system interface digital supply. Finally, by
BUSY
using the OB/ input pin, both twos complement or straight
2C
binary coding can be used.
DATA
BUS
CURRENT
CONVERSION
The two signals,
and
, control the interface.
RD
and
CS RD
CS
t12
t13
have a similar effect because they are OR’d together internally.
When at least one of these signals is HIGH, the interface
02964-0-013
outputs are in high impedance. Usually
allows the selection
CS
of each AD7651 in multicircuit applications and is held low in a
single AD7651 design. is generally used to enable the
Figure 29. Slave Parallel Data Timing for Reading (Read after Convert)
RD
CS = 0
conversion result on the data bus.
CNVST,
RD
t1
PARALLEL INTERFACE
The AD7651 is configured to use the parallel interface when
SER/ is held LOW. The data can be read either after each
PAR
BUSY
t4
conversion, which is during the next acquisition phase, or
during the following conversion, as shown in Figure 29 and
Figure 30, respectively. When the data is read during the
conversion, however, it is recommended that it is read only
during the first half of the conversion phase. This avoids any
potential feedthrough between voltage transients on the digital
interface and the most critical analog conversion circuitry.
t3
DATA
BUS
PREVIOUS
CONVERSION
t12
t13
02964-0-014
Figure 30. Slave Parallel Data Timing for Reading (Read during Convert)
The BYTESWAP pin allows a glueless interface to an 8-bit bus.
As shown in Figure 31, the LSB byte is output on D[7:0] and the
MSB is output on D[15:8] when BYTESWAP is LOW. When
BYTESWAP is HIGH, the LSB and MSB bytes are swapped and
the LSB is output on D[15:8] and the MSB is output on D[7:0].
By connecting BYTESWAP to an address line, the 16-bit data
can be read in two bytes on either D[15:8] or D[7:0].
CS
RD
BYTESWAP
SERIAL INTERFACE
HI-Z
HI-Z
HI-Z
PINS D[15:8]
PINS D[7:0]
HIGH BYTE
t12
LOW BYTE
LOW BYTE
t12
HIGH BYTE
The AD7651 is configured to use the serial interface when
SER/
is held HIGH. The AD7651 outputs 16 bits of data,
t13
PAR
HI-Z
MSB first, on the SDOUT pin. This data is synchronized with
the 16 clock pulses provided on the SCLK pin. The output data
is valid on both the rising and falling edges of the data clock.
02964-0-025
Figure 31. 8-Bit Parallel Interface
Rev. 0 | Page 20 of 28
AD7651
Usually, because the AD7651 has a longer acquisition phase than
MASTER SERIAL INTERFACE
the conversion phase, the data is read immediately after conversion.
This makes the Master Read After Conversion the most recom-
mended serial mode when it can be used. In this mode, it should be
noted that unlike in other modes, the BUSY signal returns LOW
after the 16 data bits are pulsed out and not at the end of the
conversion phase, which results in a longer BUSY width.
Internal Clock
The AD7651 is configured to generate and provide the serial data
clock SCLK when the EXT/
pin is held LOW. The AD7651 also
INT
generates a SYNC signal to indicate to the host when the serial data
is valid. The serial clock SCLK and the SYNC signal can be inverted
if desired. Depending on the RDC/SDIN input, the data can be read
after each conversion or during the following conversion. Figure 32
and Figure 33 show detailed timing diagrams of these two modes.
In the Read During Conversion mode, the serial clock and data
toggle at appropriate instants, which minimize potential feed-
through between digital activity and critical conversion decisions
RDC/SDIN = 0
INVSCLK = INVSYNC = 0
EXT/INT = 0
CS, RD
CNVST
BUSY
t3
t28
t30
t29
t25
SYNC
t14
t18
t19
t24
t20
t21
2
t26
1
3
14
15
16
SCLK
t15
t27
SDOUT
D15
D14
t23
D2
D1
D0
X
t16
t22
02964-0-015
Figure 32. Master Serial Data Timing for Reading (Read after Convert)
EXT/INT = 0
RDC/SDIN = 1
INVSCLK = INVSYNC = 0
CS, RD
CNVST
BUSY
t1
t3
t17
t25
SYNC
t14
t19
t20 t21
t24
t26
t15
SCLK
1
2
3
14
15
16
t18
t27
SDOUT
X
D15
D14
t23
D2
D1
D0
t16
t22
02964-0-016
Figure 33. Master Serial Data Timing for Reading (Read Previous Conversion during Convert)
Rev. 0 | Page 21 of 28
AD7651
SLAVE SERIAL INTERFACE
External Clock
While the AD7651 is performing a bit decision, it is important
that voltage transients be avoided on digital input/output pins or
degradation of the conversion result could occur. This is
particularly important during the second half of the conversion
phase because the AD7651 provides error correction circuitry
that can correct for an improper bit decision made during the
first half of the conversion phase. For this reason, it is
recommended that when an external clock is being provided, it
is a discontinuous clock that is toggling only when BUSY is
LOW, or, more importantly, that it does not transition during the
latter half of BUSY HIGH.
The AD7651 is configured to accept an externally supplied
serial data clock on the SCLK pin when the EXT/
pin is held
INT
HIGH. In this mode, several methods can be used to read the
data. The external serial clock is gated by . When and
RD
CS
CS
are both LOW, the data can be read after each conversion or
during the following conversion. The external clock can be
either a continuous or a discontinuous clock. A discontinuous
clock can be either normally HIGH or normally LOW when
inactive. Figure 34 and Figure 35 show the detailed timing
diagrams of these methods. Usually, because the AD7651 has a
longer acquisition phase than conversion phase, the data are
read immediately after conversion.
RD = 0
EXT/INT = 1
INVSCLK = 0
RD
BUSY
t35
t36 t37
SCLK
1
2
3
14
15
16
17
18
t31
t32
X
D15
t34
D14
D13
X13
D1
X1
X15
Y15
X14
Y14
SDOUT
SDIN
D0
X0
t16
X15
X14
t33
02964-0-017
Figure 34. Slave Serial Data Timing for Reading (Read after Convert)
RD = 0
EXT/INT = 1
INVSCLK = 0
CS
CNVST
BUSY
t3
t35
t36 t37
SCLK
1
2
3
14
15
16
t31
t32
D14
X
D1
SDOUT
D15
D13
D0
t16
02965-0-018
Figure 35. Slave Serial Data Timing for Reading (Read Previous Conversion during Convert)
Rev. 0 | Page 22 of 28
AD7651
External Discontinuous Clock Data Read After
Conversion
External Clock Data Read During Conversion
Figure 35 shows the detailed timing diagrams of this method.
During a conversion, while both and are LOW, the result
of the previous conversion can be read. The data is shifted out
MSB first with 16 clock pulses, and is valid on both the rising
and falling edges of the clock. The 16 bits must be read before
the current conversion is complete; otherwise, RDERROR is
pulsed HIGH and can be used to interrupt the host interface to
prevent incomplete data reading. There is no daisy-chain feature
in this mode and the RDC/SDIN input should always be tied
either HIGH or LOW.
Though the maximum throughput cannot be achieved using
this mode, it is the most recommended of the serial slave modes.
Figure 34 shows the detailed timing diagrams of this method.
After a conversion is complete, indicated by BUSY returning
CS
RD
LOW, the conversion’s result can be read while both
and
CS
RD
are LOW. Data is shifted out MSB first with 16 clock pulses and
is valid on the rising and falling edges of the clock.
Among the advantages of this method is the fact that conversion
performance is not degraded because there are no voltage
transients on the digital interface during the conversion process.
Another advantage is the ability to read the data at any speed up
to 40 MHz, which accommodates both the slow digital host
interface and the fastest serial reading.
To reduce performance degradation due to digital activity, a fast
discontinuous clock of at least 18 MHz is recommended to
ensure that all the bits are read during the first half of the
conversion phase. It is also possible to begin to read data after
conversion and continue to read the last bits after a new
conversion has been initiated. This allows the use of a slower
clock speed like 14 MHz.
Finally, in this mode only, the AD7651 provides a daisy-chain
feature using the RDC/SDIN pin for cascading multiple con-
verters together. This feature is useful for reducing component
count and wiring connections when desired, as, for instance, in
isolated multiconverter applications.
An example of the concatenation of two devices is shown in
Figure 36. Simultaneous sampling is possible by using a
common
signal. It should be noted that the RDC/SDIN
CNVST
input is latched on the opposite edge of SCLK of the one used to
shift out the data on SDOUT. Therefore, the MSB of the
“upstream” converter just follows the LSB of the “downstream”
converter on the next SCLK cycle.
BUSY
OUT
BUSY
BUSY
AD#72651
AD#71651
(UPSTREAM)
(DOWNSTREAM)
DATA
OUT
RDC/SDIN
SDOUT
RDC/SDIN
SDOUT
CNVST
CS
CNVST
CS
SCLK
SCLK
SCLK IN
CS IN
CNVST IN
02964-0-019
Figure 36. Two AD7651s in a Daisy-Chain Configuration
Rev. 0 | Page 23 of 28
AD7651
(MSTR) = 1, Clock Polarity bit (CPOL) = 0, Clock Phase bit
(CPHA) = 1, and SPI Interrupt Enable (TIMOD) = 00—by
writing to the SPI control register (SPICLTx). To meet all timing
requirements, the SPI clock should be limited to 17 Mbps, which
allows it to read an ADC result in less than 1 µs. When a higher
sampling rate is desired, use of one of the parallel interface
modes is recommended.
MICROPROCESSOR INTERFACING
The AD7651 is ideally suited for traditional dc measurement
applications supporting a microprocessor, and for ac signal
processing applications interfacing to a digital signal processor.
The AD7651 is designed to interface either with a parallel 8-bit
or 16-bit wide interface, or with a general-purpose serial port or
I/O ports on a microcontroller. A variety of external buffers can
be used with the AD7651 to prevent digital noise from coupling
into the ADC. The following section discusses the use of an
AD7651 with an ADSP-219x SPI equipped DSP.
DVDD
ADSP-219x*
AD7651*
SER/PAR
EXT/INT
SPI Interface (ADSP-219x)
Figure 37 shows an interface diagram between the AD7651 and
the SPI equipped ADSP-219x. To accommodate the slower
speed of the DSP, the AD7651 acts as a slave device and data
must be read after conversion. This mode also allows the daisy-
chain feature. The convert command can be initiated in
response to an internal timer interrupt. The reading process can
be initiated in response to the end-of-conversion signal (BUSY
going LOW) using an interrupt line of the DSP. The serial inter-
face (SPI) on the ADSP-219x is configured for master mode—
BUSY
CS
SDOUT
SCLK
CNVST
PFx
SPIxSEL (PFx)
MISOx
SCKx
PFx or TFSx
RD
INVSCLK
*ADDITIONAL PINS OMITTED FOR CLARITY
02964-0-021
Figure 37. Interfacing the AD7651 to an SPI Interfac
Rev. 0 | Page 24 of 28
AD7651
APPLICATION HINTS
be established as close as possible to the AD7651.
BIPOLAR AND WIDER INPUT RANGES
In some applications, it is desirable to use a bipolar or wider
analog input range such as 10 V, 5 V, or 0 V to 5 V. Although
the AD7651 has only one unipolar range, simple modifications
of input driver circuitry allow bipolar and wider input ranges to
be used without any performance degradation. Figure 38 shows
a connection diagram that allows this. Component values
required and resulting full-scale ranges are shown in Table 8.
Running digital lines under the device should be avoided since
these will couple noise onto the die. The analog ground plane
should be allowed to run under the AD7651 to avoid noise
coupling. Fast switching signals like
or clocks should be
CNVST
shielded with digital ground to avoid radiating noise to other
sections of the board, and should never run near analog signal
paths. Crossover of digital and analog signals should be avoided.
Traces on different but close layers of the board should run at
right angles to each other. This will reduce the effect of crosstalk
through the board.
When desired, accurate gain and offset can be calibrated by
acquiring a ground and voltage reference using an analog
multiplexer (U2), as shown in Figure 38.
The power supply lines to the AD7651 should use as large a
trace as possible to provide low impedance paths and reduce the
effect of glitches on the power supply lines. Good decoupling is
also important to lower the supply’s impedance presented to the
AD7651 and to reduce the magnitude of the supply spikes.
Decoupling ceramic capacitors, typically 100 nF, should be
placed on each power supply pin—AVDD, DVDD, and
OVDD—close to, and ideally right up against these pins and
their corresponding ground pins. Additionally, low ESR 10 µF
capacitors should be located near the ADC to further reduce
low frequency ripple.
C
F
R1
R2
ANALOG
INPUT
IN
U1
AD7651
U2
100nF
R3
R4
INGND
REF
C
REF
The DVDD supply of the AD7651 can be a separate supply or
can come from the analog supply AVDD or the digital interface
supply OVDD. When the system digital supply is noisy or when
fast switching digital signals are present, if no separate supply is
available, the user should connect DVDD to AVDD through an
RC filter (see Figure 22) and the system supply to OVDD and
the remaining digital circuitry. When DVDD is powered from
the system supply, it is useful to insert a bead to further reduce
high frequency spikes.
REFGND
02964-0-022
Figure 38. Using the AD7651 in 16-Bit Bipolar and/or Wider Input Ranges
Table 8. Component Values and Input Ranges
Input Range
R1 (Ω)
R2 (kΩ)
R3 (kΩ)
R4 (kΩ)
10 V
5 V
0 V to –5 V
500
500
500
4
2
1
2.5
2.5
None
2
1.67
0
The AD7651 has five different ground pins: INGND, REFGND,
AGND, DGND, and OGND. INGND is used to sense the analog
input signal. REFGND senses the reference voltage and, because
it carries pulsed currents, should be a low impedance return to
the reference. AGND is the ground to which most internal ADC
analog signals are referenced; it must be connected with the
least resistance to the analog ground plane. DGND must be tied
to the analog or digital ground plane depending on the
configuration. OGND is connected to the digital system
ground.
LAYOUT
The AD7651 has very good immunity to noise on the power
supplies. However, care should still be taken with regard to
grounding layout.
The printed circuit board that houses the AD7651 should be
designed so the analog and digital sections are separated and
confined to certain areas of the board. This facilitates the use of
ground planes that can be separated easily. Digital and analog
ground planes should be joined in only one place, preferably
underneath the AD7651, or as close as possible to the AD7651.
If the AD7651 is in a system where multiple devices require
analog-to-digital ground connections, the connection should
still be made at one point only, a star ground point that should
EVALUATING THE AD7651’S PERFORMANCE
A recommended layout for the AD7651 is outlined in the
EVAL-AD7651 evaluation board for the AD7651. The
evaluation board package includes a fully assembled and tested
evaluation board, documentation, and software for controlling
the board from a PC via the EVAL-CONTROL BRD2.
Rev. 0 | Page 25 of 28
AD7651
OUTLINE DIMENSIONS
0.75
0.60
0.45
9.00 BSC
SQ
1.60
MAX
37
48
36
25
1
PIN 1
SEATING
PLANE
10°
6°
7.00
TOP VIEW
1.45
1.40
1.35
0.20
0.09
(PINS DOWN )
BSC SQ
2°
VIEW A
7°
3.5°
0°
12
0.15
0.05
24
13
SEATING
PLANE
0.10 MAX
0.27
0.22
0.17
0.50
BSC
COPLANARITY
VIEW A
ROTATED 90
°
CCW
COMPLIANT TO JEDEC STANDARDS MS-026BBC
Figure 39. 48-Lead Quad Flatpack (LQFP) [ST-48]
Dimensions shown in millimeters
0.30
0.23
0.18
7.00
0.60 MAX
0.60 MAX
BSC SQ
PIN 1
INDICATOR
37
36
48
1
PIN 1
INDICATOR
5.25
6.75
BOTTOM
VIEW
TOP
VIEW
BSC SQ
5.10 SQ
4.95
0.50
0.40
0.30
25
24
12
13
0.25 MIN
5.50
REF
0.80 MAX
0.65 TYP
PADDLE CONNECTED TO AGND.
THIS CONNECTION IS NOT
REQUIRED TO MEET THE
1.00
0.85
0.80
ꢀ
12° MAX
0.05 MAX
0.02 NOM
ELECTRICAL PERFORMANCES
COPLANARITY
0.08
0.50 BSC
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
Figure 40. 48-Lead Frame Chip Scale Package (LFCSP) [CP-48]
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
Package Option
ST-48
ST-48
CP-48
CP-48
AD7651AST
AD7651ASTRL
AD7651ACP
AD7651ACPRL
EVAL-AD7651CB1
EVAL-CONTROL BRD22
Quad Flatpack (LQFP)
Quad Flatpack (LQFP)
Lead Frame Chip Scale (LFCSP)
Lead Frame Chip Scale (LFCSP)
Evaluation Board
Controller Board
1This board can be used as a standalone evaluation board or in conjunction with the EVAL-CONTROL BRD2 for evaluation/demonstration purposes.
2This board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators.
Rev. 0 | Page 26 of 28
AD7651
NOTES
Rev. 0 | Page 27 of 28
AD7651
NOTES
©
2003 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective companies.
C02964–0–9/03(0)
Rev. 0 | Page 28 of 28
相关型号:
AD7653ACP
IC 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, QCC48, MO-220-VKKD-2, LFCSP-48, Analog to Digital Converter
ADI
AD7653ACPZ
1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, QCC48, MO-220-VKKD-2, LFCSP-48
ROCHESTER
AD7653ASTRL
IC 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PQFP48, MS-026BBC, LQFP-48, Analog to Digital Converter
ADI
©2020 ICPDF网 联系我们和版权申明