AD7450ABRT [ADI]
IC 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8, SOT-23, 8 PIN, Analog to Digital Converter;型号: | AD7450ABRT |
厂家: | ADI |
描述: | IC 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8, SOT-23, 8 PIN, Analog to Digital Converter |
文件: | 总24页 (文件大小:428K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PRELIMINARY TECHNICAL DATA
Differential Input, 1MSPS,
a
PreliminaryTechnicalData
12-Bit ADC in µSO-8 and S0-8
AD7450
FEATURES
F U NC T IO NAL B LO C K D IAG RAM
Fast Throughput Rate: 1MSPS
Specified for VDD of 3 V and 5 V
Low Pow er at m ax Throughput Rate:
3 m W typ at 833kSPS w ith 3 V Supplies
8 m W typ at 1MSPS w ith 5 V Supplies
Fully Differential Analog Input
Wide Input Bandw idth:
V
DD
V
V
12-BIT SUCCESSIVE
IN+
APPROXIMATION
ADC
T/H
70d B S INAD a t 300kHz In p u t Fre q u e n cy
Flexible Pow er/ Serial Clock Speed Managem ent
No Pipeline Delays
IN-
V
REF
Hig h S p e e d S e ria l In t e rfa ce - S PITM/ QS PITM
/
Micro Wire TM
/ DS P Co m p a t ib le
SCLK
SDATA
CS
Po w e rd o w n Mo d e : 1µA m a x
8 Pin µSOIC and SOIC Packages
CONTROL
LOGIC
AD7450
APPLICATIONS
Transducer Interface
Battery Pow ered System s
Data Acquisition System s
Portable Instrum entation
Motor Control
Com m unications
GND
G E NE R AL D E S C R IP T IO N
T he AD7450 is a 12-bit, high speed, low power, succes-
sive-approximation (SAR) analog-to-digital converter
featuring a fully differential analog input. It operates from
a single 3 V or 5 V power supply and features throughput
rates up to 833kSPS or 1MSPS respectively.
T he SAR architecture of this part ensures that there are
no pipeline delays.
T he AD7450 uses advanced design techniques to achieve
very low power dissipation at high throughput rates.
T his part contains a low-noise, wide bandwidth, differen-
tial track and hold amplifier (T /H) which can handle
input frequencies in excess of 1MHz with the -3dB point
being 20MHz typically. T he reference voltage for the
AD7450 is applied externally to the VREF pin and can be
varied from 100 mV to 2.5 V depending on the power
supply and to suit the application. T he value of the refer-
ence voltage determines the common mode voltage range
of the part. With this truly differential input structure and
variable reference input, the user can select a variety of
input ranges and bias points.
P R O D U C T H IG H LIG H T S
1.Operation with either 3 V or 5 V power supplies.
2.H igh T hroughput with Low Power Consumption.
With a 3V supply, the AD7450 offers 3mW typ power
consumption for 833kSPS throughput.
3.Fully D ifferential Analog Input.
4.Flexible Power/Serial C lock Speed M anagement.
T he conversion rate is determined by the serial clock,
allowing the power to be reduced as the conversion time
is reduced through the serial clock speed increase. T his
part also features a shutdown mode to maximize power
efficiency at lower throughput rates.
T he conversion process and data acquisition are controlled
using CS and the serial clock allowing the device to inter-
face with Microprocessors or DSPs. T he input signals are
sampled on the falling edge of CS and the conversion is
also initiated at this point.
5.Variable Voltage Reference Input.
6.N o Pipeline D elay.
7.Accurate control of the sampling instant via a CS input
and once off conversion control.
8. ENOB > 8 bits typ with 100mV Reference.
MicroWire is a trademark of National Semiconductor Corporation.
SPI and QSPI are trademarks of Motorola, Inc.
REV. PrJ 27/02/02
Inform ation furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assum ed by Analog Devices for its
use, nor for any infringem ents of patents or other rights of third parties
which m ay result from its use. No license is granted by im plication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norw ood, MA 02062-9106, U.S.A.
Tel: 781/ 329-4700
Fax: 781/ 326-8703
w w w .analog.com
© Analog Devices, Inc., 2002
PRELIMINARY TECHNICAL DATA
( V = 2.7V to 3.3V, fSCLK = 15MHz, fS = 833kHz, V = 1.25 V;
DD
REF
1
V = 4.75V to 5.25V, fSCLK = 18MHz, fS = 1MHz, V = 2.5 V;
DD
REF
AD7450-SPECIFICATIONS
V
CM
3 = V ; T = TMIN to T , unless otherwise noted.)
REF
A
MAX
P ar am eter
A Version1 B Version1
Units
Test Conditions/Com m ents
D YN AM IC PERF O RM AN C E
FIN = 300kH z Sine Wave,
fSAMPLE= 833kSPS, 1MSPS
Signal to (Noise + Distortion) Ratio 70
(SIN AD )2
70
dB min
T otal H armonic D istortion (T H D )2 -80
-80
-80
dB max
dB max
Peak H armonic or Spurious Noise2
Intermodulation D istortion (IM D )2
Second Order T erms
-80
-78
-78
10
50
20
-78
-78
10
50
20
dB typ
dB typ
ns typ
ps typ
M H z typ
M H z typ
T hird Order T erms
Aperture D elay3
Aperture Jitter3
Full Power Bandwidth3
@ -3 dB
@ -0.1 dB
2.5
T BD
2.5
T BD d B
Common Mode Rejection Ratio
(C M RR)2
D C AC C U RAC Y
Resolution
12
12
Bits
Integral N onlinearity (IN L)2
D ifferential N onlinearity (D N L)2
Zero Code Error2
± 2
± 1
± 5
± 5
± 5
± 1
± 1
± 5
± 5
± 5
LSB max
LSB max
LSB max
LSB max
LSB max
Guaranteed No Missed Codes to 12 Bits.
Positive Gain Error2
N egative Gain Error2
AN ALO G IN PU T
Full Scale Input Span
Absolute Input Voltage
VIN +
4
VIN+ - VIN
Volts
2 x VREF
-
3
VCM ± VREF/2
Volts
Volts
VCM = VREF
VCM = VREF
3
VIN -
VCM ± VREF/2
D C Leakage Current
Input Capacitance
± 1
20
5
± 1
20
5
µA max
pF typ
pF typ
When in T rack
When in Hold
REF EREN C E IN PU T
VREF Input Voltage
2.55
2.5
Volts
Volts
5 V supply (±1% tolerance for specified
performance)
3 V supply (±1% tolerance for specified
performance)
1.256
1.25
D C Leakage Current
VREF Input Capacitance
± 1
15
± 1
15
µA max
pF typ
LO G IC IN PU T S
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
2.4
0.8
± 1
10
2.4
0.8
± 1
10
V min
V max
µA max
pF max
T ypically 10 nA, VIN = 0 V or VDD
7
Input Capacitance, CIN
LO G IC O U T P U T S
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage C urrent
Floating-State Output Capacitance7
Output C oding
2.8
0.4
± 10
10
2.8
0.4
± 10
10
V min
ISOURCE = 200µA
ISINK =200µA
V max
µA max
pF max
T wo’s C omplement
C O N VERSIO N RAT E
Conversion T ime
16
16
SC LK cycles 888ns with an 18MHz SCLK
1.07µs with a 15MHz SCLK
T rack/H old Acquisition T ime8
T hroughput Rate9
275
1
833
275
1
833
ns max
M SPS max @ VDD = 5V
kSPS max @ VDD = 3V
Sine Wave input
–2 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
P a r a m eter
A Ver sion1 B Ver sion1
Units
Test Conditions/Com m ents
P O WER REQ U IREM EN T S
VD D
3/5
1
3/5
1
Vm in /m ax Range: 3 V ± 10%; 5 V ± 5%
8 , 1 0
ID D
N ormal M ode(Static)
mA typ
VDD =3 V/5 V. SCLK On or Off
N ormal M ode (Operational)
2.6
2
1
2.6
2
1
mA max
mA max
µA max
VDD = 5 V. fSAMPLE=1MSPS
VDD = 3 V. fSAMPLE=833kSPS
SCLK On or Off
Full Power-D own M ode
Power D issipation
N ormal M ode (Operational)
13
6
5
13
6
5
mW max
mW max
µW max
µW max
VDD =5 V. fSAMPLE=1MSPS
VDD =3 V. fSAMPLE=833kSPS
VDD =5 V. SCLK On or Off
VDD =3 V. SCLK On or Off
Full Power-D own
3
3
N O T E S
1T emperature ranges as follows: A,
2See ‘T erm inology’ section.
B Versions: –40°C to + 85°C .
3C ommon M ode Voltage. T he input signal can be centered on any choice of dc C ommon M ode Voltage as long as this value is in the range
specified in Figure 8.
4Because the input span of VIN+ and VIN- are both VREF
,
and they are 180° out of phase, the differential voltage is 2 x VREF
.
5T he reference is functional from 100mV and for 5V supplies it can range up to T BD V (see ‘Reference Section’).
6T he reference is functional from 100mV and for 3V supplies it can range up to 2.2V (see ‘Reference Section’).
7Sample tested
@
+ 25°C to ensure compliance.
8See P O WE R VE RSU S T H RO U G H P U T RAT E section .
8T C ON VERT
T Q U IET (See ‘Serial Interface Section’)
10M easured with
midscale D C input.
+
a
Specifications subject to change without notice.
( V = 2.7V to 3.3V, fSCLK = 15MHz, fS = 833kHz, V = 1.25 V;
DD
REF
AD7450 -TIMINGSPECIFICATIONS1,2
V = 4.75V to 5.25V, fSCLK = 18MHz, fS = 1MHz, V = 2.5 V;
DD
REF
V
CM
3 = V ; T = TMIN to T , unless otherwise noted.)
REF
A
MAX
Lim it at T MIN, TMAX
P ar am eter
+3V
+5V
Units
D escription
4
fSC LK
10
10
kH z min
15
18
M H z max
tCONVERT
tQUIET
16 x tSCLK
1.07
50
16 x tSCLK
0.88
50
tSCLK = 1/fSCLK
SCLK = 15M H z, 18M H z
Minimum Quiet T ime between the End of a Serial Read and the
Next Falling Edge of CS
µs max
ns min
t1
t2
t3
t4
t5
t6
10
10
20
40
0.4 tSCLK
0.4 tSCLK
10
10
45
10
10
20
40
0.4 tSCLK
0.4 tSCLK
10
10
45
ns min
ns min
ns max
ns max
ns min
ns min
ns min
ns min
ns max
µs max
M inimum CS Pulsewidth
CS falling Edge to SCLK Falling Edge Setup T ime
Delay from CS Falling Edge Until SDAT A 3-State Disabled
Data Access T ime After SCLK Falling Edge
SCLK H igh Pulse Width
5
5
SCLK Low Pulse Width
t76
SCLK Edge to Data Valid Hold T ime
SCLK Falling Edge to SDAT A 3-State Enabled
SCLK Falling Edge to SDAT A 3-State Enabled
Power-Up T ime from Full Power-D own
t8
7
tP O WE R-U P
T BD
T BD
NOTES
1Sample tested at +25°C to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 Volts.
2See Figure
1 and the “Serial Interface” section.
3C om m on M od e Voltage.
4M ark/Space ratio for the SC LK input is 40/60 to 60/40.
5Measured with the load circuit of Figure 2 and defined as the time required for the output to cross 0.8 V or 2.4 V with VDD
= 5 V and time for
an output to cross 0.4 V or 2.0 V for VDD
= 3 V.
6t8 is derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 2. T he measured num-
ber is then extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. T his means that the time, t8, quoted in the
timing characteristics is the true bus relinquish time of the part and is independent of the bus loading.
7
See ‘Power-up T im e’ Section.
Specifications subject to change without notice.
–3 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
t
1
CS
t
CONVERT
t
t
2
5
B
SCLK
1
2
3
4
5
13
14
15
16
t
t
6
7
t
8
t
t
QUIET
4
t
3
0
0
0
0
DB11
DB10
DB1
DB0
DB2
SDATA
3-STATE
4 LEADING ZERO’S
Figure 1. Serial Interface Tim ing Diagram
NOTES
AB SO LUT E M AXIM UM RAT ING S1
1Stressesabove those listed under “Absolute Maximum Ratings” maycause permanent
damage to the device. Thisisa stressratingonlyand functionaloperation ofthe device
at these or any other conditions above those listed in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for
extended periods mayaffect device reliability.
(TA = +25°C unless otherwise noted)
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +7 V
VIN+ to GND . . . . . . . . . . . . . . . . . –0.3 V to VDD + 0.3 V
VIN- to GND . . . . . . . . . . . . . . . . . –0.3 V to VDD + 0.3 V
Digital Input Voltage to GND . . . -0.3 V to VDD + 0.3 V
Digital Output Voltage to GND . . -0.3 V to VDD + 0.3 V
VREF to GND . . . . . . . . . . . . . . . . . . . -0.3 V to VDD +0.3 V
Input Current to Any Pin Except Supplies2 . . . . ± 10m A
Operating T emperature Range
2T ransient currents of up to 100 mA will not cause SC R latch up.
I
OL
200µA
Commercial (A, B Version) . . . . . . . . . -40oC to +85oC
Storage T emperature Range . . . . . . . . . -65oC to +150oC
Junction T emperature . . . . . . . . . . . . . . . . . . . . . . . + 150oC
SOIC , µSOIC Package, Power D issipation . . . . 450m W
TO
OUTPUT
PIN
+1.6V
C
L
T hermal Impedance . . . . . . . . . . 157°C /W (SOIC )
205.9°C/W (µSOIC)
JA
50 pF
T hermal Impedance . . . . . . . . . . . 56°C/W (SOIC)
43.74°C/W (µSOIC)
JC
200µA
I
OH
Lead T emperature, Soldering
Vapor Phase (60 secs) . . . . . . . . . . . . . . . . . . . + 215oC
Infared (15 secs) . . . . . . . . . . . . . . . . . . . . . . . + 220oC
E S D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T BD
Figure 2. Load Circuit for Digital Output Tim ing Specifications
O R D E R ING G U ID E
Linearity
P ackage
Error (LSB)1 O ption4
Model
Range
Branding Inform ation
AD 7450AR
AD 7450ARM
AD 7450BR
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
Evaluation Board
C ontroller Board
± 2 LSB
± 2 LSB
± 1 LSB
± 1 LSB
SO -8
RM -8
SO -8
RM -8
AD 7450AR
C P A
AD 7450BR
C P B
AD 7450BRM
EVAL-AD 7450C B2
EVAL-C O N T RO L BRD 23
NOTES
1Linearityerror here refers to IntegralLinearityError.
2T his can be used as a stand-alone evaluation board or in conjunction with the EVALUAT ION BOARD CONT ROLLER for evaluation/demonstration purposes.
3EVALU AT ION BOARD C ON T ROLLER. T his board is
evaluation boards ending in the C B designators.
4S0 = SOIC; RM = µSOIC
a complete unit allowing a PC to control and communicate with all Analog D evices
C A U T I O N
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD7450 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high-energyelectrostatic discharges. T herefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
–4 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
P IN F U NC T IO N D E SC R IP T IO N
P in No. P in Mnem onic
Function
1
VREF
Reference Input for the AD7450. An external reference must be applied to this input. For a
5 V power supply, the reference is 2.5 V (±1%) and for a 3 V power supply, the reference is
1.25 V (±1%) for specified performance. T his pin should be decoupled to GND with a
capacitor of at least 0.1µF. See the ‘Reference Section’ for more details.
2
3
4
VIN +
VIN -
Positive T erminal for Differential Analog Input.
Negative T erminal for Differential Analog Input.
G N D
Analog Ground. Ground reference point for all circuitry on the AD7450. All analog input
signals and any external reference signal should be referred to this GND voltage.
5
6
CS
Chip Select. Active low logic input. T his input provides the dual function of initiating a
conversion on the AD7450 and framing the serial data transfer.
SD AT A
Serial Data. Logic Output. T he conversion result from the AD7450 is provided on this
output as a serial data stream. T he bits are clocked out on the falling edge of the SCLK
input. T he data stream consists of four leading zeros followed by the 12 bits of conversion
data which are provided MSB first. T he output coding is two’s complement.
7
8
SC L K
VD D
Serial Clock. Logic input. SCLK provides the serial clock for accessing data from the part.
T his clock input is also used as the clock source for the AD7450's conversion process.
Power Supply Input. VDD is 3 V (±10%) or 5 V (±5%). T his supply should be decoupled to
GND with a 0.1µF Capacitor and a 10µF T antalum Capacitor.
P IN C O NFIGURATIO N SO IC and µSO IC
V
V
REF
1
2
3
4
8
7
6
5
DD
AD7450
TOP VIEW
(Not to Scale)
V
IN+
SCLK
SDATA
CS
V
IN-
GND
–5 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
Ap er tu r e D ela y
T E R M I N O L O G Y
T his is the amount of time from the leading edge of the
sampling clock until the ADC actually takes the sample.
Signal to (Noise + D istor tion) Ratio
T his is the measured ratio of signal to (noise + distortion)
at the output of the ADC. T he signal is the rms amplitude
of the fundamental. Noise is the sum of all
Ap er tu r e Jitter
T his is the sample to sample variation in the effective
point in time at which the actual sample is taken.
nonfundamental signals up to half the sampling frequency
(fS/2), excluding dc. T he ratio is dependent on the number
of quantization levels in the digitization process; the more
levels, the smaller the quantization noise. T he theoretical
signal to (noise + distortion) ratio for an ideal N-bit con-
verter with a sine wave input is given by:
F u ll P ower Ban dwidth
T he full power bandwidth of an ADC is that input fre-
quency at which the amplitude of the reconstructed
fundamental is reduced by 0.1dB or 3dB for a full scale
input.
C om m on Mode Rejection Ratio (C MRR)
T he Common Mode Rejection Ratio is defined as the
ratio of the power in the ADC output at full-scale fre-
quency, f, to the power of a 200mV p-p sine wave applied
to the Common Mode Voltage of VIN+ and VIN- of fre-
quency fs:
Signal to (Noise + Distortion) = (6.02 N + 1.76) dB
T hus for a 12-bit converter, this is 74 dB.
T ota l H a r m on ic D istor tion
T otal harmonic distortion (T HD) is the ratio of the rms
sum of harmonics to the fundamental. For the AD7450, it
is defined as:
CMRR ( dB) = 10log( Pf/Pfs)
Pf is the power at the frequncy f in the ADC output; Pfs is
the power at frequency fs in the ADC output.
2
2
2
4
2
2
V2
V
V
V
V
+
6
+
+
+
3
5
THD (d B ) 20 lo g
=
In tegr a l Non lin ea r ity (INL)
V1
T his is the maximum deviation from a straight line pass-
ing through the endpoints of the ADC transfer function.
where V1 is the rms amplitude of the fundamental and V2,
V3, V4, V5 and V6 are the rms amplitudes of the second to
the sixth harmonics.
D iffer en tia l Non lin ea r ity (D NL)
T his is the difference between the measured and the ideal 1
LSB change between any two adjacent codes in the ADC.
P eak H ar m onic or Spur ious Noise
Peak harmonic or spurious noise is defined as the ratio of
the rms value of the next largest component in the ADC
output spectrum (up to fS/2 and excluding dc) to the rms
value of the fundamental. Normally, the value of this
specification is determined by the largest harmonic in the
spectrum, but for ADCs where the harmonics are buried
in the noise floor, it will be a noise peak.
Zer o C ode E r r or
T his is the deviation of the midscale code transition (111...111
to 000...000) from the ideal VIN+-VIN (i.e., 0LSB).
-
P ositive Gain E r r or
T his is the deviation of the last code transition (011...110 to
011...111) from the ideal VIN+-VIN- (i.e., +VREF - 1LSB), after
the Zero Code Error has been adjusted out.
In t er m od u la t ion D ist or t ion
With inputs consisting of sine waves at two frequencies, fa
and fb, any active device with nonlinearities will create
distortion products at sum and difference frequencies of
mfa ± nfb where m, n = 0, 1, 2, 3, etc. Intermodulation
distortion terms are those for which neither m nor n are
equal to zero. For example, the second order terms in-
clude (fa + fb) and (fa – fb), while the third order terms
include (2fa + fb), (2fa – fb), (fa + 2fb) and (fa – 2fb).
Nega tive G a in E r r or
T his is the deviation of the first code transition (100...000 to
100...001) from the ideal VIN+-VIN - (i.e., -VREF + 1LSB), after
the Zero Code Error has been adjusted out.
T r a ck/H old Acqu isition T im e
T he track/hold amplifier returns into track mode on the
13th SCLK rising edge (see the “Serial Interface Sec-
tion”). T he track/hold acquisition time is the minimum
time required for the track and hold amplifier to remain in
track mode for its output to reach and settle to within 0.5
LSB of the applied input signal.
T he AD7450 is tested using the CCIF standard where two
input frequencies near the top end of the input bandwidth
are used. In this case, the second order terms are usually
distanced in frequency from the original sine waves while
the third order terms are usually at a frequency close to
the input frequencies. As a result, the second and third
order terms are specified separately. T he calculation of the
intermodulation distortion is as per the T H D specification
where it is the ratio of the rms sum of the individual dis-
tortion products to the rms amplitude of the sum of the
fundamentals expressed in dBs.
P ower Supply Rejection (P SR)
T he power supply rejection ratio is defined as the ratio of
the power in the ADC output at full-scale frequency, f, to
the power of a 200mV p-p sine wave applied to the ADC
VDD supply of frequency fs.
PSRR (dB) = 10 log (Pf/Pfs)
Pf is the power at frequency f in the ADC output; Pfs is
the power at frequency fs in the ADC output.
–6 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
P E R F O R M ANC E C U R VE S
T PC 3 shows the signal-to-(noise+distortion) ratio
T PC 1 and T PC 2 show the typical FFT plots for the
AD7450 with VDD of 5V and 3V, 1MHz and 833kHz sam-
pling frequency respectively and an input frequency of
300kH z.
performance versus the analog input frequency for
various supply voltages while sampling at 1MSPS
(VDD = 5V±5%) and 833kSPS (VDD = 3V±10%).
0
0
0
0
8192 POINT FFT
FSAMPLE = 1MSPS
FIN = 300kHz
SINAD = 71.7dB
THD = -82.8dB
-20
SFDR = -85.3dB
-40
-60
-80
-100
-120
0
0
0
0
0
0
0
TITLE
0
50
100
150
200
250
300
350
400
450
500
FREQUENCY (kHz)
TPC 1. AD7450 Dynam ic Perform ance at 1MSPS
with VDD =5V
TPC 3. SINAD vs Analog Input Frequency
for Various Supply Voltages TBD
T PC 4 shows the power supply rejection ratio versus
supply ripple frequency for the AD7450. Here, a
200mV p-p sine wave is coupled onto the VDD supply.
A 10nF decoupling capacitor was used on the supply
0
8192 POINT FFT
f
f
SAMPLE = 833ksps
IN = 300kHz
-20
-40
and a 1µF decoupling capacitor was used on VREF
.
SINAD = 70.2dB
THD = -86dB
SFDR = -87.1dB
0
-60
-80
-100
-120
0
0
50
100
150
200
250
300
350
FREQUENCY (kHz)
TPC 2. AD7450 Dynam ic Perform ance at 833ksps with
DD = 3V
0
V
0
0
0
0
0
0
0
TITLE
TPC 4. Power Supply Rejection (see Term inology Sec-
tion) vs. Supply Ripple Frequency at 5V and 3V TBD
–7 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
T PC 7 and T PC 8 show typical INL plots for the
AD7450 with VDD of 5V and 3V, 1MHz and 833kHz
sampling frequency respectively and an input frequency of
300kH z.
T PC 5 and T PC 6 show typical DNL plots for the
AD7450 with VDD of 5V and 3V, 1MHz and 833kHz
sampling frequency respectively and an input frequency of
300kH z.
1
0.8
0.6
0.4
0.2
0
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
-0.2
-0.4
-0.6
-0.8
-1
0
1024
2048
3072
4096
0
1024
2048
3072
4096
CODE
CODE
TPC 5 Typical Differential Nonlinearity (DNL) VDD = 5V
TPC 7 Typical Integral Nonlinearity (INL) VDD = 5V
1
0.8
0.6
0.4
0.2
0
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
-0.2
-0.4
-0.6
-0.8
-1
0
1024
2048
3072
4096
0
1024
2048
3072
4096
CODE
CODE
TPC 6 Typical Differential Nonlinearity (DNL) VDD = 3V
TPC 8 Typical Integral Nonlinearity (INL) VDD = 3V
–8 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
T PC 11 and T PC 12 show the change in INL versus VREF
for VDD of 5V and 3.3V respectively.
T PC 9 and T PC 10 show the change in DNL versus VREF
for VDD of 5V and 3.3V respectively.
1.5
1
1
Positive DNL
Positive INL
0.5
0
0.5
0
-0.5
-0.5
Negative DNL
-1
Negative INL
-1
-1.5
0
0.5
1
1.5
2
2.5
0
0.5
1
1.5
2
2.5
VREF
VREF
TPC 9.Change in DNL vs Reference Voltage VDD = 5V
TPC 11. Change in INL vs Reference Voltage VDD = 5V
1.5
2
1
Positive DNL
1.5
1
0.5
0
Positive INL
0.5
0
-0.5
-0.5
Negative DNL
-1
Negative INL
-1
-1.5
0
0.6
1.2
1.8
2.4
0
0.6
1.2
1.8
2.4
VREF
VREF
TPC 12. Change in INL vs Reference Voltage VDD = 3.3V*
TPC 10. Change in DNL vs Reference Voltage VDD = 3.3V*
*See ‘Reference Section
–9 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
T PC 13 shows the change in Zero Code Error versus the
Reference Voltage for VDD = 5V and 3.3V.
T PC 15 shows a histogram plot for 10000 conversions of
a dc input for VDD of 3V. As in T PC 14, both inputs are
set to VREF. Both plots indicate good noise performance as
the majority of codes appear in one output bin.
1
VDD = 5 V
Fs = 1MSPS
0
-1
-2
-3
-4
-5
-6
-7
-8
-9
10000
9839 Codes
9000
VDD = 3.3 V
Fs = 833kSPS
8000
7000
6000
5000
4000
3000
2000
1000
0.25
0.75
1.25
1.75
2.25
2.5
VREF
71 Codes
90 Codes
0
2044
2045
2046
2047
2048
2049
CODE
TPC 13. Change in Zero Code Error vs Reference Voltage
VDD = 5V and 3.3 V*
TPC 15. Histogram of 10000 conversions of a DC Input with
DD = 3V
V
T PC 14 shows a histogram plot for 10000 conversions of
a dc input using the AD7450 with VDD = 5V. Both ana-
log inputs were set to VREF, which is the center of the
code transition.
T PC 16 shows the Effective Number of Bits (ENOB)
versus the Reference Voltage for VDD 5V and 3.3V. Note
that the AD7450 has an ENOB of greater than 8-bits typi-
cally when VREF = 100mV.
12
10000
10000 Codes
VDD = 5V
9000
8000
7000
6000
5000
4000
3000
2000
1000
0
11
10
9
8
VDD = 3.3V
Fs = 833kSPS
7
6
2044
2045
2046
2047
2048
2049
0
0.5
1
1.5
2
2.5
CODE
VREF
TPC 14. Histogram of 10000 conversions of a DC Input with
VDD = 5V
TPC 16. Change in ENOB vs Reference Voltage
VDD = 5V and 3.3 V*
*See Reference Section.
–1 0 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
T PC 17 shows the Common Mode Rejection Ratio versus
supply ripple frequency for the AD7450 for both VDD
5V and 3 V. Here a 200mV p-p sine wave is coupled onto
figure 3 (acquisition phase), SW3 is closed and SW1 and
SW2 are in position A, the comparator is held in a bal-
anced condition and the sampling capacitor arrays acquire
the differential signal on the input.
=
the Common Mode Voltage of VIN+ and VIN-
.
CAPACITIVE
DAC
90
VDD = 5 V
80
70
60
50
40
30
20
10
0
COMPARATOR
C
s
B
A
VDD = 3 V
V
IN+
CONTROL
LOGIC
SW1
SW2
SW3
A
B
V
IN-
C
s
V
REF
CAPACITIVE
DAC
Figure 3. ADC Acquisition Phase
10
100
1000
10000
When the ADC starts a conversion (figure 4), SW3 will
open and SW1 and SW2 will move to position B, causing
the comparator to become unbalanced. Both inputs are
disconnected once the conversion begins. T he Control
Logic and the charge redistribution DACs are used to add
and subtract fixed amounts of charge from the sampling
capacitor arrays to bring the comparator back into a bal-
anced condition. When the comparator is rebalanced, the
conversion is complete. T he Control Logic generates the
ADC’s output code. T he output impedances of the
sources driving the VIN+ and the VIN- pins must be
matched otherwise the two inputs will have different set-
tling times, resulting in errors.
Frequency (kHz)
TPC 17. CMRR versus Frequency for VDD = 5V and 3 V
C IR C U IT INF O R M AT IO N
T he AD7450 is a fast, low power, single supply, 12-bit
successive approximation analog-to-digital converter
(ADC). It can operate with a 5 V and 3V power supply
and is capable of throughput rates up to 1MSPS and
833kSPS when supplied with a 18MHz or 15MHz clock
respectively. T his part requires an external reference to be
applied to the VREF pin, with the value of the reference
chosen depending on the power supply and to suit the
application.
CAPACITIVE
DAC
When operated with a 5 V supply, the maximum reference
that can be applied to the part is 2.5 V and when operated
with a 3 V supply, the maximum reference that can be
applied to the part is 2.2 V. (See ‘Reference Section’).
COMPARATOR
C
s
B
A
V
IN+
SW1
SW2
CONTROL
LOGIC
SW3
A
B
V
IN-
T he AD7450 has an on-chip differential track and hold
amplifier, a successive approximation (SAR) ADC and a
serial interface, housed in either an 8-lead SOIC or
µSOIC package. T he serial clock input accesses data
from the part and also provides the clock source for the
successive-approximation ADC. T he AD7450 features a
power-down option for reduced power consumption be-
tween conversions. T he power-down feature is
C
s
V
REF
CAPACITIVE
DAC
Figure 4. ADC Conversion Phase
AD C T RANSF E R F U NC T IO N
implemented across the standard serial interface as de-
scribed in the ‘Modes of Operation’ section.
T he output coding for the AD7450 is two’s complement.
T he designed code transitions occur at successive LSB
values (i.e. 1LSB, 2LSBs, etc.) and the LSB size is
2xVREF/4096. T he ideal transfer characteristic of the
AD7450 is shown in figure 5.
C O NVE R T E R O P E R AT IO N
T he AD7450 is a successive approximation ADC based
around two capacitive DACs. Figures 3 and 4 show sim-
plified schematics of the ADC in Acquisition and
Conversion phase respectively. T he ADC comprises of
Control Logic, a SAR and two capacitive DACs.
In
–1 1 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
T H E ANALO G INP UT
1LSB = 2xV
/4096
REF
T he analog input of the AD7450 is fully differential. Dif-
ferential signals have a number of benefits over single
ended signals including noise immunity based on the
device’s common mode rejection, improvements in distor-
tion performance, doubling of the device’s available
dynamic range and flexibility in input ranges and bias
points.
011...111
011...110
000...001
000...000
111...111
Figure 7 defines the fully differential analog input of the
AD 7450.
100...010
100...001
100...000
V
REF
P-to-P
V
V
+V
- 1LSB
-V
+ 1LSB
IN+
0LSB
REF
REF
AD7450
ANALOG INPUT
(V - V
V
REF
P-to-P
)
IN+ IN-
IN-
COMMON
MODE
VOLTAGE
Figure 5. AD7450 Ideal Transfer Characteristic
T YP IC AL C O NNE C T IO N D IAG R AM
Figure 7. Differential Input Definition
Figure 6 shows a typical connection diagram for the
AD7450 for both 5 V and 3 V supplies. In this setup the
GND pin is connected to the analog ground plane of the
system. T he VREF pin is connected to either a 2.5 V or a
1.25 V decoupled reference source depending on the
power supply, to set up the analog input range. T he com-
mon mode voltage has to be set up externally and is the
value that the two inputs are centered on. For more details
on driving the differential inputs and setting up the com-
mon mode, see the ‘Driving Differential Inputs’ section.
T he conversion result for the ADC is output in a 16-bit
word consisting of four leading zeros followed by the
MSB of the 12-bit result. For applications where power
consumption is of concern, the power-down mode should
be used between conversions or bursts of several conver-
sions to improve power performance. See ‘Modes of
Operation’ section.
T he amplitude of the differential signal is the difference
between the signals applied to the VIN+ and VIN- pins (i.e.
VIN+ - VIN-).
VIN+ and VIN- are simultaneously driven by
two signals each of amplitude VREF that are 180° out of
phase. T he amplitude of the differential signal is therefore
-VREF to +VREF peak-to-peak (i.e. 2 x VREF). T his is re-
gardless of the common mode (CM). T he common mode
is the average of the two signals, i.e. (VIN+ + VIN-)/2 and
is therefore the voltage that the two inputs are centered on.
T his results in the span of each input being CM ± VREF/2.
T his voltage has to be set up externally and its range var-
ies with VREF
.
As the value of VREF increases, the
common mode range decreases. When driving the inputs
with an amplfier, the actual common mode range will be
determined by the amplifier’s output voltage swing.
Figure 8 shows how the common mode range varies with
VREF for a 5 V power supply and figure 9 shows an ex-
ample of the common mode range when using the
AD8138 differential amplifer to drive the analog inputs.
T he common mode must be in this range to guarantee the
specifications. With a 3V power supply, the Common
Mode range is T BD.
+3V/+5V
SUPPLY
0.1µF
10µF
SERIAL
INTERFACE
V
DD
V
REF
SCLK
CM*
CM*
V
IN+
P-to-P
µC/µP
SDATA
CS
AD7450
For ease of use, the common mode can be set up to be
equal to VREF, resulting in the differential signal being
V
REF
V
IN-
±VREF centered on VREF
.
When a conversion takes place,
P-to-P
GND
the common mode is rejected resulting in a virtually noise
free signal of amplitude -VREF to +VREF corresponding to
he digital codes of 0 to 4095.
V
REF
1.25V/2.5V
VREF
0.1µF
* CM - COMMON MODE VOLTAGE
Figure 6. Typical Connection Diagram
–1 2 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
0
Reference = 0.625 V (V
max/4)
REF
0.625 V peak to peak
Common Mode (CM)
CM
= 0.275 V
min
max
CM
= 3.8 V
Reference = 1.25 V (V
max/2)
REF
0
1.25 V peak to peak
Common Mode (CM)
CM
= 0.85 V
min
max
CM
= 3.55 V
Reference = 2.5 V (V
max)
REF
2.5 V peak to peak
Common Mode (CM)
0
0
0
0
0
0
0
0
CM
= 2 V
min
TITLE
CM
= 3 V
max
Figure 8. Input Com m on Mode Range (CM) versus VREF
(Vdd = 5V and VREF (m ax) = 2.5V)
Figure 10. Exam ples of the Analog Inputs to VIN+ and VIN-
for Different Values of VREF for VDD = 5 V.
5
4
3
An a log In p u t Str u ctu r e
Figure 11 shows the equivalent circuit of the analog input
structure of the AD7450. T he four diodes provide ESD
protection for the analog inputs. Care must be taken to
ensure that the analog input signals never exceed the sup-
ply rails by more than 200mV. T his will cause these
diodes to become forward biased and start conducting into
the substrate. T hese diodes can conduct up to 10mA with-
out causing irreversible damage to the part.
2.8
2
1
0.9
T he capacitors C1, in figure 11 are typically 4pF and can
primarily be attributed to pin capacitance.
T he resistors
0
are lumped components made up of the on-resistance of
the switches. T he value of these resistors is typically about
100⍀. T he capacitors, C2, are the ADC’s sampling ca-
pacitors and have a capacitance of 16pF typically.
-1
0.75
1
1.25
1.5
1.75
2
2.25
2.5
VREF
For ac applications, removing high frequency components
from the analog input signal is recommended by the use of
an RC low-pass filter on the relevant analog input pins.
In applications where harmonic distortion and signal to
noise ratio are critical, the analog input should be driven
from a low impedance source. Large source impedances
will significantly affect the ac performance of the ADC.
T his may necessitate the use of an input buffer amplifier.
T he choice of the opamp will be a function of the particu-
lar application.
Figure 9. Input Com m on Mode Range versus VREF
(Vdd = 5V and VREF (m ax) = 2.5V) when Driving VIN+ and VIN-
with the AD8138 Differential Am plifier
Figure 10 shows examples of the inputs to VIN+ and VIN-
for different values of VREF for VDD = 5 V. It also gives
the maximum and minimum common mode voltages for
each reference value according to figure 8.
–1 3 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
0
V
DD
D
C2
R1
V
IN+
C1
D
0
V
DD
D
C2
R1
V
IN-
C1
D
0
0
0
0
0
0
0
0
TITLE
Figure 13.THD vs Analog Input Frequency for 3V and 5V
Figure 11. Equivalent Analog Input Circuit.
Conversion Phase - Switches Open
Track Phase - Switches Closed
Supply Voltages TBD
D R IVING D IF F E R E NT IAL INP U T S
Differential operation requires that VIN+ and VIN- be si-
multaneously driven with two equal signals that are 180o
out of phase. T he common mode must be set up exter-
nally and has a range which is determined by VREF, the
power supply and the particular amplifier used to drive the
analog inputs (see figure 8). Differential modes of opera-
tion with either an ac or dc input, provide the best T HD
performance over a wide frequency range. Since not all
applications have a signal preconditioned for differential
operation, there is often a need to perform single ended to
differential conversion.
When no amplifier is used to drive the analog input, the
source impedance should be limited to low values. T he
maximum source impedance will depend on the amount of
T otal H armonic Distortion (T H D) that can be tolerated.
T he T HD will increase as the source impedance increases
and performance will degrade. Figure 12 shows a graph
of the T HD versus analog input signal frequency for dif-
ferent source impedances.
0
D iffer en tia l Am p lifier
An ideal method of applying dc differential drive to the
AD7450 is to use a differential amplifier such as the AD8138.
T his part can be used as a single ended to differential
amplifier or as a differential to differential amplifier. In both
cases the analog input needs to be bipolar. It also provides
common mode level shifting and buffering of the bipolar
input signal. Figure 14 shows how the AD8138 can be used
as a single ended to differential amplifier. T he positive and
negative outputs of the AD8138 are connected to the respec-
tive inputs on the AD C via a pair of series resistors to
minimize the effects of switched capacitance on the front end
of the ADC. T he RC low pass filter on each analog input is
recommended in ac applications to remove high frequency
components of the analog input. T he architecture of the
AD8138 results in outputs that are very highly balanced over
a wide frequency range without requiring tightly matched
external components.
0
0
0
0
0
0
0
0
0
TITLE
Figure 12.THD vs Analog Input Frequency for Various
Source Im pedances TBD
If the analog input source being used has no impedance then
all four resistors (Rg1, Rg2, Rf1, Rf2) should be the same. If
the source has a 50 ⍀ impedance and a 50 ⍀ termination for
example, the value of Rg2 should be increased by 25 ⍀ to
balance this parallel impedance on the input and thus ensure
that both the positive and negative analog inputs have the
same gain (see figure 14). T he outputs of the amplifier are
perfectly matched, balanced differential outputs of identical
amplitude and are exactly 180o out of phase.
Figure 13 shows a graph of T HD versus analog input
frequency for VDD of 5V and 3V, while sampling at
1MHz and 833kHz with a SCLK of 18 MHz and 15MHz
respectively.
–1 4 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
T he AD8138 is specified with 3 V, 5 V and ±5 V power
supplies but the best results are obtained when it is supplied
by ±5 V. A lower cost device that could also be used in this
configuration with slight differences in characteristics to the
AD8138 but with similar performance and operation is the
AD 8132.
220
V
REF P-to-P
V+
V-
V
DD
390
220
27
GND
V
V
IN+
AD7450
220
220
.
3.75V
2.5V
IN-
V
REF
Rf1
V+
V-
1.25V
0.1µF
Rs*
Rs*
Rg1
V
V
27
IN+
A
C*
C*
V
+2.5V
GND
ocm
AD7450
AD8138
Rf2
51R Rg2
10K
20K
V
REF
EXTERNAL
IN-
-2.5V
V
REF
3.75V
.
.
2.5V
1.25V
Figure 15(a). Dual Opam p Circuit to Convert a Single Ended
Bipolar Input into a Differential Input
EXTERNAL
*Mount as close to the AD7450 as
possible and ensure high
V
(2.5V)
REF
precision Rs and Cs are used
.
220
V
REF P-to-P
Rs - 10R; C - 1nF;
V+
V-
V
DD
Rg1=Rf1=Rf2= 499R; Rg2 = 523R
390
27
VREF/2
GND
Figure 14. Using the AD8138 as a Single Ended to Differen-
tial Am plifier
V
V
IN+
AD7450
220
220
.
O p a m p P a ir
IN-
V
REF
An opamp pair can be used to directly couple a differential
signal to the AD7450. T he circuit configurations shown
in figures 15(a) and 15(b) show how a dual opamp can be
used to convert a single ended signal into a differential
signal for both a bipolar and a unipolar input signal re-
spectively.
V+
V-
0.1µF
A
27
10K
EXTERNAL
V
REF
T he voltage applied to point A is the Common Mode
Voltage. In both diagrams, it is connected in some way to
the reference but any value in the common mode range can
be input here to setup the common mode. Examples of
suitable dual opamps that could be used in this configura-
tion to provide differential drive to the AD7450 are the
AD8042, AD8056 and the AD8022.
.
Figure 15(b). Dual Opam p Circuit to Convert a Single Ended
Unipolar Input into a Differential Input
RF T r a n sfor m er
In systems that do not need to be dc-coupled, an RF trans-
former with a center tap offers a good solution for
generating differential inputs. Figure 16 shows how a
transformer is used for single ended to differential conver-
sion. It provides the benefits of operating the ADC in the
differential mode without contributing additional noise
and distortion. An RF transformer also has the benefit of
providing electrical isolation between the signal source
and the ADC. A transformer can be used for most ac ap-
plications. T he center tap is used to shift the differential
signal to the common mode level required, in this case it
is connected to the reference so the common mode level is
the value of the reference.
Care must be taken when chosing the opamp used, as the
selection will depend on the required power supply and the
system performance objectives. T he driver circuits in fig-
ures 15(a) and 15(b) are optimized for dc coupling
applications requiring optimum distortion performance.
T he differential op-amp driver circuit in figure 15(a) is
configured to convert and level shift a 2.5 V p-p single
ended, ground referenced (bipolar) signal to a 5 V p-p
differential signal centered at the VREF level of the ADC.
T he circuit configuration shown in figure 15(b) converts a
unipolar, single ended signal into a differential signal.
–1 5 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
Table I Exam ples of Suitable Voltage Refer ences
3.75V
2.5V
Refer ence O utput
Voltage
Initial
Accur acy
(% m ax)
O per ating
Cur r ent
(µA)
1.25V
R
R
V
IN+
AD7450
C
AD589
AD1580
REF192
REF43
AD780
1.235
1.225
2.5
2.5
2.5
1.2-2.8
50
50
45
600
1000
V
REF
V
0.08-0.8
0.08-0.4
0.06-0.1
0.04-0.2
IN-
R
3.75V
2.5V
1.25V
EXTERNAL
(2.5V)
V
REF
Figure 16. Using an RF Transform er to Generate
Differential Inputs
V
DD
AD7450*
AD780
R E F E R E NC E S E C T IO N
8
OpSel
NC
NC
NC
1
2
V
REF
An external reference source is required to supply the
reference to the AD7450. T his reference input can range
from 100 mV to 2.5 V. With a 5V power supply, the
specified and maximum reference is 2.5V. With a 3V
power supply, the specified reference is 1.25V and the
maximum reference is 2.2V. In both cases, the reference is
functional from 100mV. It is important to note that as the
reference input moves closer to the maximum reference
input, the performance improves. When operating the
device from VDD = 2.7V to 3.3V, the maximum analog
VDD
0.1µF
VIN
Temp
GND
7
6
Vout
Trim
3
4
0.1µF
0.1µF
10nF
5
NC
*ADDITIONAL PINS OMITTED FOR CLARITY
input range (VINmax) must never be greater than VDD
0.3V to comply with the maximum ratings of the device.
+
Figure 17. Typical VREF Connection Diagram
SING LE E ND E D O P E R AT IO N
When supplied with a 5 V power supply, the AD7450 can
handle a single ended input. T he design of this part is
optimized for differential operation so with a single ended
input performance will degrade. Linearity will degrade by
typically 0.2LSBs, Zero Code and the Full Scale Errors
will degrade by typically 2LSBs and AC performance is
not guaranteed.
For example:
VINmax = VDD + 0.3
VINmax = VREF + VREF/2
If VDD = 3.3V
then VINmax = 3.6 V
Therefore 3xVREF/2 = 3.6 V
VREF m a x = 2.4 V
T o operate the AD7450 in single ended mode, the VIN+
input is coupled to the signal source while the VIN- input is
biased to the appropriate voltage corresponding to the
mid-scale code transition. T his voltage is the Common
Mode, which is a fixed dc voltage (usually the reference).
T he VIN+ input swings around this value and should have
voltage span of 2 x VREF to make use of the full dynamic
range of the part. T he input signal will therefore have peak
T herefore, when operating at VDD = 3.3 V, the value of
VREF can range from 100mV to a maximum value of 2.4V.
When VDD = 2.7 V, VREF max = 2 V.
When operating from VDD
=
4.75 V to 5.25 V, there is
no need to worry about the maximum analog input in
relation to VDD as the maximum VREF is 2.5 V resulting
the maximum analog input span being 3.75 V which is not
to peak values of Common Mode ±VREF
.
If the analog
close to VDD
.
input is unipolar then an opamp in a non-inverting
unity gain configuration can be used to drive the VIN+ pin.
Because the ADC operates from a single supply, it will be
necessary to level shift ground based bipolar signals to
T he performance of the part at different reference values is
shown in T PC9 to T PC13 and in T PC16 and T PC17.
T he value of the reference sets the analog input span and
the common mode voltage range. Errors in the reference
source will result in gain errors in the AD7450 transfer
function and will add to specified full scale errors on the
part. A capacitor of 0.1µF should be used to decouple the
VREF pin to GND. T able I lists examples of suitable volt-
age references that could be used that are available from
Analog Devices and Figure 17 shows a typical connection
diagram for the VREF pin.
comply with the input requirements.
An opamp can be
configured to rescale and level shift the ground based bi-
polar signal so it is compatible with the selected input
range of the AD7450 (see Figure 18).
–1 6 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
In applications with a slower SCLK, it may be possible to
read in data on each SCLK rising edge i.e. the first rising
edge of SCLK after the CS falling edge would have the
leading zero provided and the 15th SCLK edge would have
D B0 provided.
+5V
+2.5V
0V
R
+2.5V
0V
R
R
V
IN
V
IN+
AD7450
-2.5V
R
T im ing E xam ple 1
Having FSCLK = 18MHz and a throughput rate of
1MSPS gives a cycle time of:
V
IN-
V
REF
0.1µF
EXTERNAL
(2.5V)
V
REF
1/T hroughput = 1/1000000 = 1µs
A cycle consists of:
Figure 18. Applying a Bipolar Single Ended Input to the
AD7450
t2 + 12.5 (1/FSCLK) + tACQ = 1µs.
T herefore if t2 = 10ns then:
SE R IAL INT E R F AC E
Figure 19 shows a detailed timing diagram for the serial
interface of the AD7450. T he serial clock provides the
conversion clock and also controls the transfer of data
from the AD7450 during conversion. CS initiates the
conversion process and frames the data transfer. T he fall-
ing edge of CS puts the track and hold into hold mode
and takes the bus out of three-state. T he analog input is
sampled and the conversion initiated at this point. T he
conversion will require 16 SCLK cycles to complete.
10ns + 12.5(1/18MHz) + tACQ = 1µs
tACQ = 296ns
T his 296ns satisfies the requirement of 275ns for tACQ
From Figure 20, tACQ comprises of:
.
2.5(1/FSCLK) + t8 + tQUIET
Once 13 SCLK falling edges have occurred, the track and
hold will go back into track on the next SCLK rising edge
as shown at point B in Figure 19. On the 16th SCLK
falling edge the SDAT A line will go back into three-state.
where t8 = 45ns. T his allows a value of 113ns for tQUIET
satisfying the minimum requirement of 100ns.
T im ing E xam ple 2
Having FSCLK = 5MHz and a throughput rate of
315kSPS gives a cycle time of :
If the rising edge of CS occurs before 16 SCLKs have
elapsed, the conversion will be terminated and the SDAT A
line will go back into three-state on the 16th SCLK falling
edge. 16 serial clock cycles are required to perform a
conversion and to access data from the AD7450. CS going
low provides the first leading zero to be read in by the micro-
controller or DSP. T he remaining data is then clocked out
on the subsequent SCLK falling edges beginning with the
second leading zero. T hus the first falling clock edge on the
serial clock provides the second leading zero. T he final bit
in the data transfer is valid on the 16th falling edge, having
been clocked out on the previous (15th) falling edge.
1/T hroughput = 1/315000 = 3.174µs
A cycle consists of:
t2 + 12.5 (1/FSCLK) + tACQ = 3.174µs.
T herefore if t2 is 10ns then:
10ns + 12.5(1/5MHz) + tACQ = 3.174µs
tACQ = 664ns
t
1
CS
t
CONVERT
t
t
2
5
B
SCLK
1
2
3
4
5
13
14
15
16
t
t
6
7
t
8
t
t
QUIET
4
t
3
0
0
0
0
DB11
DB10
DB1
DB0
DB2
SDATA
3-STATE
4 LEADING ZERO’S
Figure 19. Serial interface Tim ing Diagram
–1 7 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
CS
t
CONVERT
t
t
2
B
C
10ns
5
SCLK
1
2
3
4
5
13
14
15
16
t
6
t
8
tQUIET
t
)
12.5(1/f
ACQUISITION
SCLK
1/Throughput
Figure 20. Serial Interface Tim ing exam ple
T his 664ns satisfies the requirement of 275ns for tACQ
From Figure 20, tACQ comprises of:
.
Sixteen serial clock cycles are required to complete the
conversion and access the complete conversion result. CS
may idle high until the next conversion or may idle low
until sometime prior to the next conversion. Once a data
transfer is complete, i.e. when SDAT A has returned to
three-state, another conversion can be initiated after the
quiet time, tQUIET has elapsed by again bringing CS low.
2.5(1/FSCLK) + t8 + tQUIET
where t8 = 45ns. T his allows a value of 119ns for tQUIET
satisfying the minimum requirement of 100ns.
CS
As in this example and with other slower clock values, the
signal may already be acquired before the conversion is
complete but it is still necessary to leave 100ns minimum
tQUIET between conversions. In example 2 the signal should
be fully acquired at approximately point C in Figure 20.
1
16
10
SCLK
M O D E S O F O P E R AT IO N
SDATA
4 LEADING ZEROS + CONVERSION RESULT
T he mode of operation of the AD 7450 is selected by
controlling the logic state of the CS signal during a
conversion. T here are two possible modes of operation,
Normal Mode and Power-Down Mode. T he point at which
CS is pulled high after the conversion has been initiated will
determine whether or not the AD7450 will enter the power-
down mode. Similarly, if already in power-down, CS
controls whether the device will return to normal operation
or remain in power-down. T hese modes of operation are
designed to provide flexible power management options.
T hese options can be chosen to optimize the power dissipa-
tion/throughpu t rate ratio for d iffering application
requirements.
Figure 21. Norm al Mode Operation
P ower D own Mode
T his mode is intended for use in applications where
slower throughput rates are required; either the ADC is
powered down between each conversion, or a series of
conversions may be performed at a high throughput rate
and the ADC is then powered down for a relatively long
duration between these bursts of several conversions.
When the AD7450 is in the power down mode, all analog
circuitry is powered down. T o enter power down mode,
the conversion process must be interrupted by bringing
CS high anywhere after the second falling edge of SCLK
and before the tenth falling edge of SCLK as shown in
Figure 22.
Nor m a l M od e
T his mode is intended for fastest throughput rate perfor-
mance. T he user does not have to worry about any
power-up times as the AD7450 is kept fully powered up.
Figure 21 shows the general diagram of the operation of
the AD7450 in this mode. T he conversion is initiated on
the falling edge of CS as described in the ‘Serial Interface
Section’. T o ensure the part remains fully powered up,
CS must remain low until at least 10 SCLK falling edges
have elapsed after the falling edge of CS.
Once CS has been brought high in this window of
SCLKs, the part will enter power down and the conver-
sion that was initiated by the falling edge of CS will be
terminated and SDAT A will go back into three-state.
T he time from the rising edge of CS to SDAT A three-
state enabled will never be greater than t8 (see the
‘T iming Specifications’). If CS is brought high before
the second SCLK falling edge, the part will remain in
normal mode and will not power-down. T his will avoid
accidental power-down due to glitches on the CS line.
If CS is brought high any time after the 10th SCLK fall-
ing edge, but before the 16th SCLK falling edge, the part
will remain powered up but the conversion will be termi-
nated and SDAT A will go back into three-state.
–1 8 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
In order to exit this mode of operation and power the
AD7450 up again, a dummy conversion is performed. On
the falling edge of CS the device will begin to power up,
and will continue to power up as long as CS is held low
until after the falling edge of the 10th SCLK. T he device
will be fully powered up after 1µsec has elapsed and, as
shown in Figure 23, valid data will result from the next
conversion.
Although at any SCLK frequency one dummy cycle is
sufficient to power the device up and acquire VIN, it does
not necessarily mean that a full dummy cycle of 16
SCLKs must always elapse to power up the device and
acquire VIN fully; 1µs will be sufficient to power the de-
vice up and acquire the input signal.
For example, if a 5MHz SCLK frequency was applied to
the ADC, the cycle time would be 3.2µs (i.e. 1/(5MHz)
x 16). In one dummy cycle, 3.2µs, the part would be
powered up and VIN acquired fully. However after 1µs
with a 5MHz SCLK only 5 SCLK cycles would have
elapsed. At this stage, the ADC would be fully powered
up and the signal acquired. So, in this case the CS can
be brought high after the 10th SCLK falling edge and
brought low again after a time tQUIET to initiate the con-
version.
If CS is brought high before the 10th falling edge of
SCLK, the AD7450 will again go back into power-down.
T his avoids accidental power-up due to glitches on the CS
line or an inadvertent burst of eight SCLK cycles while
CS is low. So although the device may begin to power up
on the falling edge of CS, it will again power-down on the
rising edge of CS as long as it occurs before the 10th
SC LK falling edge.
When power supplies are first applied to the AD7450,
the ADC may either power up in the power-down mode
or normal mode. Because of this, it is best to allow a
dummy cycle to elapse to ensure the part is fully powered
up before attempting a valid conversion. Likewise, if the
user wishes the part to power up in power-down mode,
then the dummy cycle may be used to ensure the device is
in power-down by executing a cycle such as that shown in
Figure 22.
CS
10
1
2
SCLK
THREE STATE
SDATA
Figure 22. Entering Power Down Mode
Once supplies are applied to the AD7450, the power up
time is the same as that when powering up from the
power-down mode. It takes approximately 1µs to power
up fully if the part powers up in normal mode. It is not
necessary to wait 1µs before executing a dummy cycle to
ensure the desired mode of operation. Instead, the
dummy cycle can occur directly after power is supplied to
the ADC. If the first valid conversion is then performed
directly after the dummy conversion, care must be taken
to ensure that adequate acquisition time has been al-
lowed.
P ower up Tim e
T he power up time of the AD7450 is typically 1µsec,
which means that with any frequency of SCLK up to
18MHz, one dummy cycle will always be sufficient to
allow the device to power-up. Once the dummy cycle is
complete, the ADC will be fully powered up and the input
signal will be acquired properly. T he quiet time tQUIET
must still be allowed from the point at which the bus goes
back into three-state after the dummy conversion, to the
next falling edge of CS.
As mentioned earlier, when powering up from the power-
down mode, the part will return to track upon the first
SCLK edge applied after the falling edge of CS. How-
ever, when the ADC powers up initially after supplies are
applied, the track and hold will already be in track. T his
means if (assuming one has the facility to monitor the
ADC supply current) the ADC powers up in the desired
mode of operation and thus a dummy cycle is not re-
When running at the maximum throughput rate of
1MSPS, the AD7450 will power up and acquire a signal
within ±0.5LSB in one dummy cycle, i.e. 1µs. When
powering up from the power-down mode with a dummy
cycle, as in Figure 23, the track and hold, which was in
hold mode while the part was powered down, returns to
track mode after the first SCLK edge the part receives
after the falling edge of CS. T his is shown as point A in
Figure 23.
t
POWERUP
THE PART BEGINS
TO POWER UP
THE PART IS FULLY POWERED
UP WITH VIN FULLY ACQUIRED
CS
A
10
16
1
10
16
SCLK
1
SDATA
INVALID DATA
VALID DATA
Figure 23. Exiting Power Down Mode
–1 9 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
quired to change mode, then neither is a dummy cycle
required to place the track and hold into track.
100
10
VDD
SCLK
=
5V
18M Hz
P O WE R VE RSUS T H RO UG H P UT RAT E
=
By using the power-down mode on the AD7450 when not
converting, the average power consumption of the ADC
decreases at lower throughput rates. Figure 24 shows
how, as the throughput rate is reduced, the device remains
in its power-down state longer and the average power con-
sumption reduces accordingly. It shows this for both 5V
and 3V power supplies.
1
VDD
SCLK
=
3V
15M Hz
=
0.1
For example, if the AD7450 is operated in continous sam-
pling mode with a throughput rate of 100kSPS and an
SCLK of 18MHz and the device is placed in the power
down mode between conversions, then the power con-
sumption is calculated as follows:
0.01
0
50
100
150
200
250
300
350
TH ROU GH PU T (kSPS)
Power dissipation during normal operation = 13mW max
(for VDD = 5V).
Figure 24. AD7450 Power versus Throughput Rate for
Power Down Mode
If the power up time is 1 dummy cycle i.e. 1µsec, and the
remaining conversion time is another cycle i.e. 1µsec, then
the AD7450 can be said to dissipate 13mW for 2µsec*
during each conversion cycle.
If the throughput rate = 100kSPS then the cycle time =
10µsec and the average power dissipated during each cycle
is:
(2/10) x 13mW = 2.6mW
For the same scenario, if VDD = 3V, the power dissipation
during normal operation is 6mW max.
T he AD7450 can now be said to dissipate 6mW for 2µsec*
during each conversion cycle.
T he average power dissipated during each cycle with a
throughput rate of 100kSPS is therefore:
(2/10) x 6mW = 1.2mW
T his is how the power numbers in Figure 24 are calcu-
lated.
For throughput rates above 320kSPS, it is recommended
that for optimum power performance, the serial clock fre-
quency is reduced.
*T his figure assumes a very small time used to enter the power down
mode. T his will increase as the burst of clocks used to enter the power
down mode is increased.
–2 0 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
= 1 and T XM = 1. T he format bit, FO, may be set to 1
to set the word length to 8-bits, in order to implement the
power-down mode on the AD7450. T he connection dia-
gram is shown in Figure 26. It should be noted that for
signal processing applications, it is imperative that the
frame synchronisation signal from the T M S320C5x/C54x
will provide equidistant sampling.
MICRO P RO CESSO R AND D SP INTERFACING
T he serial interface on the AD7450 allows the part to be
directly connected to a range of different microproces-
sors. T his section explains how to interface the AD7450
with some of the more common microcontroller and DSP
serial interface protocols.
AD 7450 to AD SP 21xx
T he ADSP21xx family of DSPs are interfaced directly to
the AD7450 without any glue logic required.
T he SPORT control register should be set up as follows:
T FSW = RFSW = 1, Alternate Framing
INVRFS = INVT FS = 1, Active Low Frame Signal
DT YPE = 00, Right Justify Data
TMS320C5x/C54x*
AD7450*
SCLK
CLKX
CLKR
DR
SDATA
SLEN = 1111, 16-Bit Data words
ISCLK = 1, Internal serial clock
T FSR = RFSR = 1, Frame every word
IRFS = 0,
FSX
FSR
CS
IT FS = 1.
*ADDITIONAL PINS OMITTED FOR CLARITY
T o implement the power-down mode SLEN should be
set to 1001 to issue an 8-bit SCLK burst.
Figure 26. Interfacing to the TMS320C5x/C54x
T he connection diagram is shown in Figure 25. T he
ADSP21xx has the T FS and RFS of the SPORT tied
together, with T FS set as an output and RFS set as an
input. T he DSP operates in Alternate Framing Mode and
the SPORT control register is set up as described. T he
Frame Synchronisation signal generated on the T FS is
tied to CS and as with all signal processing applications
equidistant sampling is necessary. However, in this ex-
ample, the timer interrupt is used to control the sampling
rate of the ADC and under certain conditions, equidistant
sampling may not be acheived.
T he timer registers etc., are loaded with a value which
will provide an interrupt at the required sample interval.
When an interrupt is received, a value is transmitted with
T FS/DT (ADC control word). T he T FS is used to con-
trol the RFS and hence the reading of data. T he frequency
of the serial clock is set in the SCLKDIV register. When
the instruction to transmit with T FS is given, (i.e.
AX0=T X0), the state of the SCLK is checked. T he DSP
will wait until the SCLK has gone High, Low and High
before transmission will start. If the timer and SCLK val-
ues are chosen such that the instruction to transmit occurs
on or near the rising edge of SCLK, then the data may be
transmitted or it may wait until the next clock edge.
For example, the ADSP-2111 has a master clock fre-
quency of 16MHz. If the SCLKDIV register is loaded
with the value 3 then a SCLK of 2MHz is obtained, and 8
master clock periods will elapse for every 1 SCLK period.
If the timer registers are loaded with the value 803, then
100.5 SCLKs will occur between interrupts and subse-
quently between transmit instructions. T his situation will
result in non-equidistant sampling as the transmit instruc-
tion is occuring on a SCLK edge. If the number of
SCLKs between interrupts is a whole integer figure of N
then equidistant sampling will be implemented by the
D SP .
ADSP21xx*
AD7450*
SCLK
SCLK
DR
SDATA
CS
RFS
TFS
.
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 25. Interfacing to the ADSP 21xx
AD 7450 to MC 68H C 16
T he Serial Peripheral Interface (SPI) on the MC68HC16
is configured for Master Mode (MST R = 1), Clock Polar-
ity Bit (CPOL) = 1 and the Clock Phase Bit (CPHA) = 0.
T he SPI is configured by writing to the SPI Control Reg-
ister (SPCR) - see 68HC16 user manual. T he serial
transfer will take place as a 16-bit operation when the
SIZE bit in the SPCR register is set to SIZE = 1. T o
implement the power-down modes with an 8-bit transfer
set SIZE = 0. A connection diagram is shown in figure
27.
AD 7450 to T MS320C 5x/C 54x
T he serial interface on the T MS320C5x/C54x uses a
continuous serial clock and frame synchronization signals
to synchronize the data transfer operations with peripheral
devices like the AD7450. T he CS input allows easy
interfacing between the T MS320C5x/C54x and the
AD7450 without any glue logic required. T he serial port
of the T MS320C5x/C54x is set up to operate in burst
mode with internal CLKX (T X serial clock) and FSX
(T X frame sync). T he serial port control register (SPC)
must have the following setup: FO = 0, FSM = 1, MCM
–2 1 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
*
AD7450*
MC68HC16*
SCLK
SCLK/PMC2
MISO/PMC0
SS/PMC3
SDATA
CS
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 27. Interfacing to the MC68HC16
AD 7450 to D SP 56xxx
T he connection diagram in figure 28 shows how the
AD7450 can be connected to the SSI (Synchronous Serial
Interface) of the DSP56xxx family of DSPs from
Motorola. T he SSI is operated in Synchronous Mode
(SYN bit in CRB =1) with internally generated 1-bit clock
period frame sync for both T x and Rx (bits FSL1 =1 and
FSL0 =0 in CRB). Set the word length to 16 by setting
bits WL1 =1 and WL0 = 0 in CRA. T o implement the
power-down mode on the AD7450 then the word length
can be changed to 8 bits by setting bits WL1 = 0 and WL0
= 0 in CRA. It should be noted that for signal processing
applications, it is imperative that the frame
synchronisation signal from the DSP56xxx will
provideequidistant sampling.
*
AD7450*
DSP56xxx*
SCLK
SCLK
SDATA
SRD
SR2
CS
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 28. Interfacing to the DSP56xx
–2 2 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
AP P LIC AT IO N H INT S
G r ou n d in g a n d La you t
T he printed circuit board that houses the AD7450 should
be designed so that the analog and digital sections are
separated and confined to certain areas of the board. T his
facilitates the use of ground planes that can be easily sepa-
rated. A minimum etch technique is generally best for
ground planes as it gives the best shielding. Digital and
analog ground planes should be joined in only one place
and the connection should be a star ground point estab-
lished as close to the GND pin on the AD7450 as
possible. Avoid running digital lines under the device as
this will couple noise onto the die. T he analog ground
plane should be allowed to run under the AD7450 to
avoid noise coupling. T he power supply lines to the
AD7450 should use as large a trace as possible to provide
low impedance paths and reduce the effects of glitches on
the power supply line.
Fast switching signals like clocks should be shielded with
digital ground to avoid radiating noise to other sections
of the board, and clock signals should never run near the
analog inputs. Avoid crossover of digital and analog sig-
nals. T races on opposite sides of the board should run at
right angles to each other. T his will reduce the effects of
feedthrough through the board. A microstrip technique is
by far the best but is not always possible with a double-
sided board.
In this technique the component side of the board is dedi-
cated to ground planes while signals are placed on the
solder side.
Good decoupling is also important. All analog supplies
should be decoupled with 10µF tantalum capacitors in
parallel with 0.1µF capacitors to GND. T o achieve the
best from these decoupling components, they must be
placed as close as possible to the device.
E VALUAT ING T H E AD 7450 P E RF O RM ANC E
T he recommended layout for the AD7450 is outlined in
the evaluation board for the AD7450. T he evaluation
board package includes a fully assembled and tested evalu-
ation board, documentation and software for controlling
the board from a PC via the EVALUAT ION BOARD
C ON T ROLLER. T he EVALU AT ION BOARD C ON -
T ROLLER can be used in conjunction with the AD7450
evaluation board, as well as many other Analog Devices’
evaluation boards ending with the CB designator, to dem-
onstrate/evaluate the ac and dc performance of the
AD 7450.
T he software allows the user the perform ac (fast Fourier
T ransform) and dc (Histogram of codes) tests on the
AD 7450.
–2 3 –
REV. PrJ
PRELIMINARY TECHNICAL DATA
AD7450
O U T LINE D IM E NS IO NS
D imensions shown in inches and (mm).
8-lead SO IC (SO -8)
0.1968 (5.00)
0.1890 (4.80)
8
1
5
4
0.1574 (4.00)
0.1497 (3.80)
0.2440 (6.20)
0.2284 (5.80)
PIN 1
0.0688 (1.75)
0.0532 (1.35)
0 .0196 (0.5 0)
0 .0099 (0.2 5)
x 45°
0.0098 (0.25)
0.0040 (0.10)
8°
0°
0.0500
(1 .27)
BSC
0.0192 (0.49)
0.0138 (0.35)
SEATING
PLANE
0.0098 (0.25)
0.0075 (0.19)
0.0500 (1.27)
0.0160 (0.41)
8-lead m icr oSO IC (RM-8)
0.122 (3.10)
0.114 (2.90)
5
4
8
1
0.199 (5.05)
0.187 (4.75)
0.122 (3.10)
0.114 (2.90)
PIN 1
0.0256 (0.65) BSC
0.120 (3.05)
0.112 (2.84)
0.120 (3.05)
0.112 (2.84)
0.043 (1.09)
0.037 (0.94)
0.006 (0.15)
0.002 (0.05)
33°
27°
0.018 (0.46)
SEATING
PLANE
0.011 (0.28)
0.003 (0.08)
0.028 (0.71)
0.016 (0.41)
0.008 (0.20)
–2 4 –
REV. PrJ
相关型号:
AD7450AR
ADC, Successive Approximation, 12-Bit, 1 Func, 1 Channel, Serial Access, PDSO8, SOIC-8
ROCHESTER
AD7450AR-REEL
ADC, Successive Approximation, 12-Bit, 1 Func, 1 Channel, Serial Access, PDSO8, SOIC-8
ROCHESTER
AD7450AR-REEL7
ADC, Successive Approximation, 12-Bit, 1 Func, 1 Channel, Serial Access, PDSO8, SOIC-8
ROCHESTER
AD7450ARM-REEL
ADC, Successive Approximation, 12-Bit, 1 Func, 1 Channel, Serial Access, PDSO8, MICRO, SOIC-8
ROCHESTER
AD7450ARM-REEL7
ADC, Successive Approximation, 12-Bit, 1 Func, 1 Channel, Serial Access, PDSO8, MICRO, SOIC-8
ROCHESTER
©2020 ICPDF网 联系我们和版权申明