AD7415ARTZ-500RL7 [ADI]
IC,TEMPERATURE SENSOR,TSOP,5PIN,PLASTIC;
| 型号： | AD7415ARTZ-500RL7 |
| 厂家： | 
ADI |
| 描述： | IC,TEMPERATURE SENSOR,TSOP,5PIN,PLASTIC |
| 文件： | 总16页 (文件大小：166K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
؎0.5؇C Accurate, 10-Bit Digital
Temperature Sensors in SOT-23
AD7414/AD7415
FEATURES
FUNCTIONAL BLOCK DIAGRAM
10-Bit Temperature-to-Digital Converter
Temperature Range: –40؇C to +125؇C
Typical Accuracy of ؎0.5؇C at +40؇C
SMBus/I2C®-Compatible Serial Interface
3 A Power-Down Current
Temperature Conversion Time: 29 s Typ
Space-Saving 6-Lead (AD7414) and 5-Lead (AD7415)
SOT-23 Packages
10-BIT
ANALOG-DIGITAL
CONVERTER
BAND GAP
TEMPERATURE
SENSOR
GND
V
DD
CONFIGURATION
REGISTER
TEMPERATURE
VALUE
REGISTER
T
SETPOINT
HIGH
REGISTER
Pin Selectable Addressing via AS
Overtemperature Indicator (AD7414 Only)
SMBus Alert Function (AD7414 Only)
4 Versions Allow 8 I2C Addresses (AD7414)
2 Versions Allow 6 I2C Addresses (AD7415)
SETPOINT
COMPARATOR
T
SETPOINT
ALERT
LOW
REGISTER
SCL
SDA
2
SMBus/I C
INTERFACE
AS
APPLICATIONS
Hard Disk Drives
AD7414
AD7415
Personal Computers
Electronic Test Equipment
Office Equipment
Domestic Appliances
Process Control
10-BIT
BAND GAP
TEMPERATURE
SENSOR
ANALOG-DIGITAL
CONVERTER
GND
V
DD
Cellular Phones
TEMPERATURE
VALUE
REGISTER
CONFIGURATION
REGISTER
GENERAL DESCRIPTION
AS
The AD7414/AD7415 is a complete temperature monitoring
system in 6-lead and 5-lead SOT-23 packages. It contains a
band gap temperature sensor and a 10-bit ADC to monitor and
digitize the temperature reading to a resolution of 0.25°C.
SCL
SDA
2
SMBus/I C
INTERFACE
The AD7414/AD7415 provides a 2-wire serial interface that is
compatible with SMBus and I2C interfaces. The part comes in
four versions: the AD7414/AD7415-0, AD7414/AD7415-1,
AD7414-2, and AD7414-3. The AD7414/AD7415-0 and
AD7414/AD7415-1 versions provide a choice of three different
SMBus addresses for each version. All four AD7414 versions
give the possibility of eight different I2C addresses while the two
AD7415 versions allow up to six I2C addresses to be used.
PRODUCT HIGHLIGHTS
1. The AD7414/AD7415 has an on-chip temperature sensor that
allows an accurate measurement of the ambient temperature
to be made. It is capable of Ϯ0.5°C temperature accuracy.
2. SMBus/I2C-compatible serial interface with pin selectable
choice of three addresses per version of the AD7414/AD7415,
eight address options in total for the AD7414, and six in
total for the AD7415.
The AD7414/AD7415’s 2.7 V supply voltage, low supply
current, serial interface, and small package size make it ideal for
a variety of applications, including personal computers, office
equipment, cellular phones, and domestic appliances.
3. Supply voltage of 2.7 V to 5.5 V.
4. Space-saving 5-lead and 6-lead SOT-23 packages.
5. 10-bit temperature reading to 0.25°C resolution.
In the AD7414, on-chip registers can be programmed with high
and low temperature limits, and an open-drain overtemperature
indicator output (ALERT) becomes active when a programmed limit
is exceeded. A configuration register allows programming of the
state of the ALERT output (active high or active low). This
output can be used as an interrupt or as an SMBus alert.
6. The AD7414 has an overtemperature indicator that can be
software disabled. Used as an interrupt of SMBus alert.
7. One-shot and automatic temperature conversion rates.
Purchase of licensed I2C components of Analog Devices or one of its sublicensed
Associated Companies conveys a license for the purchaser under the Philips I2C
Patent Rights to use these components in an I2C system, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
REV. D
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, norforanyinfringementsofpatentsorotherrightsofthirdpartiesthat
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
AD7414/AD7415–SPECIFICATIONS1
(TA = TMIN to TMAX, VDD = 2.7 V to 5.5 V, unless otherwise noted.)
Parameter
A Version
Unit
Test Conditions/Comments
TEMPERATURE SENSOR AND ADC
Accuracy2
0.5
°C typ
°C max
°C max
°C max
°C max
°C typ
°C max
°C typ
°C max
°C typ
Bits
VDD = 3 V @ +40°C
–0.87 to +0.823
VDD = 3 V @ +40°C
1.5
2.0
3.0
2.0
1.873
2.0
3.0
3.0
10
VDD = 3 V @ –40°C to +70°C
VDD = 3 V @ –40°C to +85°C
VDD = 3 V @ –40°C to +125°C
V
DD = 3 V @ –40°C to +125°C
VDD = 5.5 V @ +40°C
VDD = 5.5 V @ –40°C to +85°C
VDD = 5.5 V @ –40°C to +85°C
VDD = 5.5 V @ –40°C to +125°C
Resolution
Update Rate, tR
Temperature Conversion Time
800
25
ms typ
µs typ
POWER SUPPLIES
Supply Current4
Peak Supply Current5
Supply Current – Nonconverting
Inactive Serial Bus6
Normal Mode @ 3 V
Normal Mode @ 5 V
Active Serial Bus7
1.2
900
mA typ
µA max
Current during Conversion
Peak Current between Conversions
169
188
µA typ
µA typ
Supply Current with Serial Bus Inactive. Part not
converting and D7 of Configuration Register = 0.
Normal Mode @ 3 V
Normal Mode @ 5 V
Shutdown Mode
180
214
3
µA typ
µA typ
µA max
Supply Current with Serial Bus Active. Part not
converting and D7 of Configuration Register = 0.
D7 of Configuration Register = 1. Typical values
are 0.04 µA at 3 V and 0.5 µA at 5 V.
DIGITAL INPUT
Input High Voltage, VIH
Input Low Voltage, VIL
Input Current, IIN
2.4
0.8
1
V min
V max
µA max
pF max
8
VIN = 0 V to VDD
All Digital Inputs
Input Capacitance, CIN
10
DIGITAL OUTPUT (OPEN-DRAIN)
Output High Voltage, VOH
Output Low Voltage, VOL
Output High Current, IOH
Output Capacitance, COUT
2.4
0.4
1
10
0.8
V min
V max
µA max
pF max
V max
IOL = 1.6 mA
VOH = 5 V
Typ = 3 pF
IOUT = 4 mA
ALERT Output Saturation Voltage
AC ELECTRICAL CHARACTERISTICS9, 10
Serial Clock Period, t1
Data In Setup Time to SCL High, t2
Data Out Stable after SCL Low, t3
SDA Low Setup Time to SCL Low
(Start Condition), t4
2.5
50
0
µs min
ns min
ns min
See Figure 1
See Figure 1
See Figure 1
50
ns min
See Figure 1
SDA High Hold Time after SCL High
(Stop Condition), t5
SDA and SCL Fall Time, t6
Power-Up Time
50
90
4
ns min
ns max
µs typ
See Figure 1
See Figure 1
NOTES
1 Temperature range as follows: A Version = –40°C to +125°C.
2 Accuracy specifications apply only to voltages listed under Test Conditions. See Temperature Accuracy vs. Supply section for typical accuracy performance over the full VDD
supply range.
3 100% production tested at 40°C to these limits.
4 These current values can be used to determine average power consumption at different one-shot conversion rates. Average power consumption at the automatic conversion rate
of 1.25 kHz is 940 µW.
5 This peak supply current is required for 29 µs (the conversion time plus power-up time) out of every 800 µs (the conversion rate).
6 These current values are derived by not issuing a stop condition at the end of a write or read, thus preventing the part from going into a conversion.
7 The current is derived assuming a 400 kHz serial clock being active continuously.
8 On power-up, the initial input current, IIN, on the AS pin is typically 50 µA.
9 The SDA and SCL timing is measured with the input filters turned on so as to meet the Fast Mode I2C specification. Switching off the input filters improves the transfer rate
but has a negative effect on the EMC behavior of the part.
10 Guaranteed by design. Not tested in production.
Specifications subject to change without notice.
–2–
REV. D
AD7414/AD7415
PIN FUNCTION DESCRIPTIONS
Mnemonic Description
PIN CONFIGURATIONS
SOT-23
AS
Logic Input. Address select input that selects one
of three I2C addresses for the AD7414/AD7415
(see Table I). Recommend a pull-up or pull-down
resistor of 1 kΩ.
SDA
AS
1
6
AD7414
Top View
(Not to Scale)
GND
2
5
4
ALERT
SCL
GND
VDD
Analog and Digital Ground
V
3
DD
Positive Supply Voltage, 2.7 V to 5.5 V
SDA
Digital I/O. Serial bus bidirectional data. Open-
drain output.
MSOP
ALERT
SCL
AD7414 Digital Output. Overtemperature indicator
becomes active when temperature exceeds THIGH
Open-drain output.
.
NC
8
NC
1
AD7414
Top View
(Not to Scale)
SDA
ALERT
SCL
2
7
6
5
AS
Digital Input. Serial bus clock.
3
4
GND
ABSOLUTE MAXIMUM RATINGS1
V
DD
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
SDA Input Voltage to GND . . . . . . . . . . . . . . –0.3 V to +7 V
SDA Output Voltage to GND . . . . . . . . . . . . . –0.3 V to +7 V
SCL Input Voltage to GND . . . . . . . . . . . . . . –0.3 V to +7 V
ALERT Output Voltage to GND . . . . . . . . . . –0.3 V to +7 V
Operating Temperature Range . . . . . . . . . . –40°C to +125°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
5-Lead SOT-23 (RJ-5)
NC = NO CONNECT
SOT-23
AS
1
5
SDA
SCL
AD7415
Top View
(Not to Scale)
GND
2
3
Power Dissipation2 . . . . . . . . . . . . . . . . . WMAX = (TJMAX – TA3)/
JA
V
4
Thermal Impedance4
DD
JA, Junction-to-Ambient (still air) . . . . . . . . . . . 240°C/W
6-Lead SOT-23 (RJ-6)
Table I. I2C Address Selection
AS Pin
Power Dissipation2 . . . . . . . . . . . . . . . . . WMAX = (TJMAX – TA3)/
JA
Thermal Impedance4
Part Number
I2C Address
JA, Junction-to-Ambient (still air) . . . . . . . . . .190.4°C/W
8-Lead MSOP (RM-8)
AD7414-0
AD7414-0
AD7414-0
Float
GND
VDD
1001 000
1001 001
1001 010
Power Dissipation2 . . . . . . . . . . . . . . . . . WMAX = (TJMAX – TA3)/
JA
Thermal Impedance4
JA, Junction-to-Ambient (still air) . . . . . . . . . .205.9°C/W
JC, Junction-to-Case . . . . . . . . . . . . . . . . . . . .43.74°C/W
AD7414-1
AD7414-1
AD7414-1
Float
GND
VDD
1001 100
1001 101
1001 110
NOTES
1 Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2 Values relate to package being used on a standard 2-layer PCB.
3TA = ambient temperature.
AD7414-2
AD7414-3
N/A
N/A
1001 011
1001 111
AD7415-0
AD7415-0
AD7415-0
Float
GND
VDD
1001 000
1001 001
1001 010
4Junction-to-case resistance is applicable to components featuring a preferential
flow direction, e.g., components mounted on a heat sink. Junction-to-ambient
resistance is more useful for air-cooled, PCB-mounted components.
AD7415-1
AD7415-1
AD7415-1
Float
GND
VDD
1001 100
1001 101
1001 110
t1
SCL
t4
t2
t5
SDA
DATA IN
t3
SDA
DATA OUT
t6
Figure 1. Diagram for Serial Bus Timing
REV. D
–3–
AD7414/AD7415
ORDERING GUIDE
Temperature
Range
Typ Temperature Package Package
Minimum
Branding Quantities/Reel
Model
Error @ 3 V
Option
Description
AD7414ART-0REEL7
AD7414ART-0REEL
AD7414ART-0500RL7
AD7414ARM-0REEL7
AD7414ARM-0REEL
AD7414ARM-0
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
2°C
2°C
2°C
2°C
2°C
2°C
RT-6
RT-6
RT-6
RM-8
RM-8
RM-8
6-Lead SOT-23 CHA
6-Lead SOT-23 CHA
6-Lead SOT-23 CHA
3,000
10,000
500
3,000
10,000
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
CHA
CHA
CHA
AD7414ART-1REEL7
AD7414ART-1REEL
AD7414ART-1500RL7
AD7414ARM-1REEL7
AD7414ARM-1REEL
AD7414ARM-1
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
2°C
2°C
2°C
2°C
2°C
2°C
RT-6
RT-6
RT-6
RM-8
RM-8
RM-8
6-Lead SOT-23 CHB
6-Lead SOT-23 CHB
6-Lead SOT-23 CHB
3,000
10,000
500
3,000
10,000
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
CHB
CHB
CHB
AD7414ART-2REEL7
AD7414ART-2REEL
–40°C to +125°C
–40°C to +125°C
2°C
2°C
RT-6
RT-6
6-Lead SOT-23 CHC
6-Lead SOT-23 CHC
3,000
10,000
AD7414ART-3REEL7
AD7414ART-3REEL
–40°C to +125°C
–40°C to +125°C
2°C
2°C
RT-6
RT-6
6-Lead SOT-23 CHD
6-Lead SOT-23 CHD
3,000
10,000
AD7415ART-0REEL7
AD7415ART-0REEL
AD7415ART-0500RL7
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
2°C
2°C
2°C
RT-5
RT-5
RT-5
5-Lead SOT-23 CGA
5-Lead SOT-23 CGA
5-Lead SOT-23 CGA
3,000
10,000
500
AD7415ART-1REEL7
AD7415ART-1REEL
AD7415ART-1500RL7
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
2°C
2°C
2°C
RT-5
RT-5
RT-5
5-Lead SOT-23 CGB
5-Lead SOT-23 CGB
5-Lead SOT-23 CGB
3,000
10,000
500
AD7415ARTZ-500RL7*
AD7415ARTZ-0REEL*
AD7415ARTZ-0REEL7*
AD7415ARTZ-1500RL7*
AD7415ARTZ-1REEL*
AD7415ARTZ-1REEL7*
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
2°C
2°C
2°C
2°C
2°C
2°C
RT-5
RT-5
RT-5
RT-5
RT-5
RT-5
5-Lead SOT-23 CGB
5-Lead SOT-23 CGB
5-Lead SOT-23 CGB
5-Lead SOT-23 CGB
5-Lead SOT-23 CGB
5-Lead SOT-23 CGB
500
500
500
500
500
500
EVAL-AD7414/AD7415EB
Evaluation Board
*Z = Pb-free part.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD7414/AD7415 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
–4–
REV. D
AD7414/AD7415
SUPPLY
2.7V TO
5.5V
CIRCUIT INFORMATION
The AD7414/AD7415 is a standalone digital temperature sensor.
The on-chip temperature sensor allows an accurate measurement
of the ambient device temperature to be made. The 10-bit A/D
converter converts the temperature measured into a twos comple-
ment format for storage in the temperature register. The A/D
converter is made up of a conventional successive-approximation
converter based around a capacitor DAC. The serial interface is
I2C and SMBus compatible. The AD7414/AD7415 requires a
2.7 V to 5.5 V power supply. The temperature sensor has a
working measurement range of –40°C to +125°C.
1k⍀
10F
0.1F
V
DD
SDA
AS
C/P
SCL
GND
ALERT
AD7414
Figure 2. Typical Connection Diagram
MEASUREMENT TECHNIQUE
FUNCTIONAL DESCRIPTION
A common method of measuring temperature is to exploit the
negative temperature coefficient of a diode, or the base-emitter
voltage of a transistor, operated at constant current. Unfortu-
nately, this technique requires calibration to null the effect of
the absolute value of VBE, which varies from device to device.
Temperature measurement is initiated by a couple of methods.
The first uses an internal clock countdown of 800 ms, and a
conversion is performed. The internal oscillator is the only circuit
that is powered up between conversions, and once it times out,
every 800 ms, a wake-up signal is sent to power up the rest of
the circuitry. A monostable is activated at the beginning of the
wake-up signal to ensure that sufficient time is given to the power-
up process. The monostable typically takes 4 µs to time out. It
then takes typically 25 µs for each conversion to be completed.
The new temperature value is loaded into the temperature value
register and ready for reading by the I2C interface.
The technique used in the AD7414/AD7415 is to measure the
change in VBE when the device is operated at two different currents.
This is given by
∆VBE = KT q ×1n N
(
)
where:
K is Boltzmann’s constant.
A temperature measurement is also initiated every time the
one-shot method is used. This method requires the user to
write to the one-shot bit in the configuration register when a
temperature measurement is needed. Setting the one-shot bit
to a 1 will start a temperature conversion directly after the
write operation. The track-and-hold goes into hold approxi-
mately 4 µs (monostable timeout) after the STOP condition
and a conversion is then initiated. Typically 25 µs later, the
conversion is complete and the temperature value register is
loaded with a new temperature value.
q is the charge on the electron (1.6 × 10–19 Coulombs).
T is the absolute temperature in Kelvins.
N is the ratio of the two currents.
V
DD
N
؋
I I
V
+
OUT
The measurement modes are compared with a high temperature
limit, stored in an 8-bit read/write register. This is applicable only
to the AD7414 since the AD7415 does not have an ALERT pin
and subsequently does not have an overtemperature monitoring
function. If the measurement is greater than the high limit, the
ALERT pin is activated (if it has already been enabled in the
configuration register). There are two ways to deactivate the
ALERT pin again: when the alert reset bit in the configuration
register is set to a 1 by a write operation, and when the tempera-
ture measured is less than the value in the TLOW register. This
ALERT pin is compatible with the SMBus SMBALERT
option.
TO ADC
V
–
SENSING
TRANSISTOR
OUT
SENSING
TRANSISTOR
Figure 3. Temperature Measurement Technique
Figure 3 shows the method the AD7414/AD7415 uses to measure
the ambient device temperature. To measure ∆VBE, the sensor
(substrate transistor) is switched between operating currents of
I and N × I. The resulting waveform is passed through a chopper-
stabilized amplifier that performs the functions of amplification
and rectification of the waveform to produce a dc voltage propor-
tional to ∆VBE. This voltage is measured by the ADC to give a
temperature output in 10-bit twos complement format.
Configuration functions consist of
• Switching between normal operation and full power-down
• Enabling or disabling the SCL and SDA filters
• Enabling or disabling the ALERT function
• Setting ALERT pin polarity
REV. D
–5–
AD7414/AD7415
TEMPERATURE DATA FORMAT
The AD7415 has three internal registers as shown in Figure 5.
Two are data registers and one is an address pointer register.
The temperature resolution of the ADC is 0.25°C, which
corresponds to 1 LSB of the ADC. The ADC can theoretically
measure a temperature span of 255°C; the practical lowest
value is limited to –40°C due to the device maximum ratings.
The A grade can measure a temperature range of –40°C to
+125°C. (Temperature data format is shown in Table II.)
TEMPERATURE
VALUE
REGISTER
ADDRESS
D
POINTER
A
REGISTER
T
CONFIGURATION
A
Table II. A Grade Temperature Data Format
Digital Output
REGISTER
Temperature
DB9 . . . DB0
SDA
SERIAL BUS INTERFACE
–55°C
–50°C
–25°C
–0.25°C
0°C
+0.25°C
+10°C
+25°C
+50°C
+75°C
+100°C
+125°C
11 0010 0100
11 0011 1000
11 1001 1100
11 1111 1111
00 0000 0000
00 0000 0001
00 0010 1000
00 0110 0100
00 1100 1000
01 0010 1100
01 1001 0000
01 1111 0100
SCL
Figure 5. AD7415 Register Structure
Each data register has an address pointed to by the address
pointer register when communicating with it. The temperature
value register is the only data register that is read-only.
ADDRESS POINTER REGISTER
The address pointer register is an 8-bit register that stores an
address that points to one of the four data registers of the
AD7414 and one of the two data registers of the AD7415. The
first byte of every serial write operation to the AD7414/AD7415
is the address of one of the data registers, which is stored in the
address pointer register, and selects the data register to which
subsequent data bytes are written. Only the 2 LSBs of this regis-
ter are used to select a data register.
A Grade Temperature Conversion Formula:
ADC Code
Positive Temperature =
4
Table III. Address Pointer Register
ADC*Code – 512
(
)
Negative Temperature =
4
P7
P6
P5
P4
P3
P2
P1
P0
*DB9 is removed from the ADC Code.
0
0
0
0
0
0
Register Select
INTERNAL REGISTER STRUCTURE
The AD7414 has five internal registers as shown in Figure 4.
Four are data registers and one is an address pointer register.
Table IV. AD7414 Register Address
Registers
P1
P0
TEMPERATURE
VALUE
REGISTER
0
0
1
1
0
1
0
1
Temperature Value Register (Read-Only)
Configuration Register (Read/Write)
THIGH Register (Read/Write)
TLOW Register (Read/Write)
CONFIGURATION
REGISTER
Table V. AD7415 Register Address
Registers
D
ADDRESS
A
POINTER
T
A
REGISTER
P1
P0
T
HIGH
REGISTER
0
0
0
1
Temperature Value Register (Read-Only)
Configuration Register (Read/Write)
T
LOW
REGISTER
Table VI. AD7414 Configuration Register
D7 D6
D5
D4
D3
ALERT ONE TEST
POLARITY RESET SHOT MODE
0* 0* 0* 0s*
D2
D1 D0
SDA
SCL
PD FLTR ALERT ALERT
SERIAL BUS INTERFACE
EN
0*
0* 1*
Figure 4. AD7414 Register Structure
*Default settings at power-up.
–6–
REV. D
AD7414/AD7415
CONFIGURATION REGISTER (ADDRESS 01H)
Table VIII. AD7415 Configuration Register
The configuration register is an 8-bit read/write register that is
used to set the operating modes of the AD7414/AD7415. In the
AD7414, six of the MSBs are used (D7 to D2) to set the operating
modes (see Table VII). D0 and D1 are used for factory settings
and must have zeros written to them during normal operation.
D7
D6
D5
D4
D3
D2
D1
D0
PD
FLTR TEST MODE
ONE
SHOT MODE
0s* 0s*
TEST
0*
1*
0s*
*Default settings at power-up.
Table VII. AD7414 Configuration Register Setting
In the AD7415, only three of the bits are used (D7, D6, and
D2) to set the operating modes (see Table IX). D0, D1, and D3
to D5 are used for factory settings and must have zeros written
to them during normal operation.
D7
D6
D5
D4
Full Power-Down if = 1.
Bypass SDA and SCL filtering if = 0.
Disable ALERT if = 1.
ALERT is active low if D4 = 0,
ALERT is active high if D4 = 1.
Table IX. AD7415 Configuration Register Settings
D3
Reset the ALERT pin if set to 1. The next temperature
conversion will have the ability to activate the ALERT
function. The bit status is not stored; thus this bit will
be 0 if read.
Initiate a temperature conversion if set to a 1. The bit
status is not stored; thus this bit will be 0 if read.
D7
D6
D2
Full Power-Down if = 1.
Bypass SDA and SCL filtering if = 0.
Initiate a temperature conversion if set to a 1. The bit
status is not stored; thus this bit will be 0 if read.
D2
If the AD7414/AD7415 is in power-down mode (D7 = 1), a
temperature conversion can still be initiated by the one-shot
operation. This involves a write operation to the configuration
register and setting the one-shot bit to a 1 (D2 = 1), which will
cause the AD7414/AD7415 to power up, perform a single
conversion, and power down again. This is a very power
efficient mode.
1
9
1
9
SCL
1
0
0
1
A2
A1
A0
P6
P5
P3
P1
R/W
P7
P4
P2
P0
SDA
START BY
ACK. BY
AD7414/AD7415
ACK. BY
AD7414/AD7415
STOP BY
MASTER
MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
Figure 6. Writing to the Address Pointer Register to Select a Register for a Subsequent Read Operation
1
1
9
1
9
SCL
SDA
R/W
0
0
A2
A1
A0
P7
P6
P5
P3
P2
P1
P0
1
P4
START BY
MASTER
ACK. BY
AD7414/AD7415
ACK. BY
AD7414/AD7415
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
1
9
SCL (CONTINUED)
SDA (CONTINUED)
D6
D5
D3
D2
D1
D0
D7
D4
ACK. BY
STOP BY
AD7414/AD7415 MASTER
FRAME 3
DATA BYTE
Figure 7. Writing to the Address Pointer Register Followed by a Single Byte of Data to the Selected Register
REV. D
–7–
AD7414/AD7415
TEMPERATURE VALUE REGISTER (ADDRESS 00H)
The temperature value register is a 10-bit read-only register
that stores the temperature reading from the ADC in twos
complement format. Two reads are necessary to read data
from this register. Table X shows the contents of the first byte
to be read, while Table XI and Table XII show the contents of
the second byte to be read from AD7414 and AD7415, respec-
tively. In Table XI, D3 to D5 of the second byte are used as
flag bits and are obtained from other internal registers. They
function as follows:
Table XI. AD7414 Temperature Value Register (Second Read)
D7 D6
B1 LSB ALERT_ THIGH
Flag Flag
D5
D4
D3
D2
D1
D0
_
TLOW
Flag
_
0
0
0
Table XII. AD7415 Temperature Value Register (Second Read)
D7
D6
D5
D4
D3
D2
D1
D0
B1
LSB
N/A
N/A
N/A
N/A
N/A
N/A
ALERT_Flag: The state of this bit is the same as that of the
ALERT pin.
AD7414 THIGH REGISTER (Address 02h)
The THIGH register is an 8-bit read/write register that stores the
upper limit that will activate the ALERT output. Therefore, if
the value in the temperature value register is greater than the
value in the THIGH register, the ALERT pin is activated (that is,
if ALERT is enabled in the configuration register). Since it is an
8-bit register, the temperature resolution is 1°C.
T
HIGH_Flag:
This flag is set to a 1 when the temperature
measured goes above the THIGH limit. It is
reset when the second temperature byte
(Table XI) is read. If the temperature is still
greater than the THIGH limit after the read
operation, the flag will be set again.
T
LOW_Flag:
This flag is set to a 1 when the temperature
measured goes below the TLOW limit. It is
reset when the second temperature byte
(Table XI) is read. If the temperature is still
less than the TLOW limit after the read operation,
the flag will be set again.
Table XIII. THIGH Register
D7
D6
D5
D4
D3
D2
D1
D0
MSB
B6
B5
B4
B3
B2
B1
B0
AD7414 TLOW REGISTER (Address 03h)
The full theoretical span of the ADC is 255°C, but in practice
the temperature measurement range is limited to the operating
range of the device, –40°C to +125°C for A grade.
The TLOW register is an 8-bit read/write register that stores the
lower limit that will deactivate the ALERT output. Therefore,
if the value in the temperature value register is less than the
value in the TLOW register, the ALERT pin is deactivated (that
is, if ALERT is enabled in the configuration register). Since it is
an 8-bit register, the temperature resolution is 1°C.
Table X. Temperature Value Register (First Read)
D15
D14
D13
D12
D11
D10
D9
D8
MSB
B8
B7
B6
B5
B4
B3
B2
1
1
9
1
9
SCL
0
0
1
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
R/W
SDA
START BY
MASTER
ACK. BY
AD7414/AD7415
NO ACK. BY STOP BY
MASTER MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
SINGLE DATA BYTE FROM AD7414/AD7415
Figure 8. Reading a Single Byte of Data from a Selected Register
1
1
9
1
9
SCL
0
0
1
A2
A1
A0
D15
D14
D13
D10 D11
FRAME 2
D9
D8
SDA
START BY
R/W
D12
ACK. BY
AD7414/AD7415
ACK. BY
MASTER
MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
MOST SIGNIFICANT DATA BYTE FROM AD7414/AD7415
9
1
SCL (CONTINUED)
SDA (CONTINUED)
D6
D5
D3
D2
D1
D0
D7
D4
NO ACK. BY STOP BY
MASTER MASTER
FRAME 3
LEAST SIGNIFICANT DATA BYTE FROM AD7414/AD7415
Figure 9. Reading Two Bytes of Data from the Temperature Value Register
–8–
REV. D
AD7414/AD7415
Table XIV. TLOW Register
Any number of bytes of data may be transferred over the serial
bus in one operation, but it is not possible to mix read and write
in one operation because the type of operation is determined at
the beginning and cannot be changed subsequently without
starting a new operation.
D7
D6
D5
D4
D3
D2
D1
D0
MSB
B6
B5
B4
B3
B2
B1
B0
AD7414/AD7415 SERIAL INTERFACE
WRITING TO THE AD7414/AD7415
Depending on the register being written to, there are two different
writes for the AD7414/AD7415.
Control of the AD7414/AD7415 is carried out via the I2C-
compatible serial bus. The AD7414/AD7415 is connected to
this bus as a slave device, under the control of a master device,
e.g., the processor.
Writing to the Address Pointer Register for a Subsequent Read
In order to read data from a particular register, the address
pointer register must contain the address of that register. If it
does not, the correct address must be written to the address
pointer register by performing a single-byte write operation, as
shown in Figure 6. The write operation consists of the serial bus
address followed by the address pointer byte. No data is written
to any of the data registers. A read operation is then performed
to read the register.
SERIAL BUS ADDRESS
Like all I2C-compatible devices, the AD7414/AD7415 has a 7-bit
serial address. The four MSBs of this address for the AD7414/
AD7415 are set to 1001. The AD7414/AD7415 comes in four
versions: AD7414/AD7415-0, AD7414/AD7415-1, AD7414-2,
and AD7414-3. The first two versions have three different I2C
addresses available, which are selected by either tying the AS
pin to GND, to VDD, or letting the pin float (see Table I). By
giving different addresses for the four versions, up to eight
AD7414s or six AD7415s can be connected to a single serial
bus, or the addresses can be set to avoid conflicts with other
devices on the bus.
Writing a Single Byte of Data to the Configuration Register,
THIGH Register, or TLOW Register
All three registers are 8-bit registers so only one byte of data can
be written to each register. Writing a single byte of data to one
of these registers consists of the serial bus address, the data
register address written to the address pointer register, followed
by the data byte written to the selected data register. This is
illustrated in Figure 7.
The serial bus protocol operates as follows:
1. The master initiates data transfer by establishing a START
condition, defined as a high to low transition on the serial
data line SDA, while the serial clock line SCL remains high.
This indicates that an address/data stream will follow. All
slave peripherals connected to the serial bus respond to the
START condition and shift in the next eight bits, consisting
of a 7-bit address (MSB first) plus an R/W bit, which deter-
mines the direction of the data transfer, i.e., whether data
will be written to or read from the slave device.
READING DATA FROM THE AD7414/AD7415
Reading data from the AD7414/AD7415 is a 1- or 2-byte opera-
tion. Reading back the contents of the configuration register,
THIGH register, or TLOW register is a single-byte read operation,
as shown in Figure 8. The register address was previously set up
by a single-byte write operation to the address pointer register.
Once the register address has been set up, any number of reads
can subsequently be done from that register without having to
write to the address pointer register again. To read from another
register, the address pointer register will have to be written to
again to set up the relevant register address.
The peripheral whose address corresponds to the transmitted
address responds by pulling the data line low during the low
period before the ninth clock pulse, known as the acknowl-
edge bit. All other devices on the bus now remain idle while
the selected device waits for data to be read from or written
to it. If the R/W bit is a 0, the master will write to the slave
device. If the R/W bit is a 1, the master will read from the
slave device.
Reading data from the temperature value register is a 2-byte
operation, as shown in Figure 9. The same rules apply for a
2-byte read as a single-byte read.
SMBus ALERT
2. Data is sent over the serial bus in sequences of nine clock
pulses, eight bits of data followed by an acknowledge bit
from the receiver of data. Transitions on the data line must
occur during the low period of the clock signal and remain
stable during the high period, since a low to high transition
when the clock is high may be interpreted as a STOP signal.
The AD7414 ALERT output is an SMBus interrupt line for
devices that want to trade their ability to master for an extra pin.
The AD7414 is a slave-only device and uses the SMBus ALERT
to signal to the host device that it wants to talk. The SMBus
ALERT on the AD7414 is used as an overtemperature indicator.
The ALERT pin has an open-drain configuration that allows the
ALERT outputs of several AD7414s to be wire-AND’ed together
when the ALERT pin is active low. Use D4 of the configuration
register to set the active polarity of the ALERT output. The
power-up default is active low. The ALERT function can be
disabled or enabled by setting D5 of the configuration register to
1 or 0, respectively.
3. When all data bytes have been read or written, stop conditions
are established. In WRITE mode, the master will pull the
data line high during the 10th clock pulse to assert a STOP
condition. In READ mode, the master device will pull the
data line high during the low period before the ninth clock
pulse. This is known as No Acknowledge. The master will
then take the data line low during the low period before the
10th clock pulse, then high during the 10th clock pulse to
assert a STOP condition.
REV. D
–9–
AD7414/AD7415
The host device can process the ALERT interrupt and simulta-
neously access all SMBus ALERT devices through the alert
response address. Only the device that pulled the ALERT low
will acknowledge the ARA (Alert Response Address). If more
than one device pulls the ALERT pin low, the highest priority
(lowest address) device will win communication rights via stan-
dard I2C arbitration during the slave address transfer.
When a temperature measurement is required, a write operation
can be performed to power up the part and put it into one-shot
mode (setting D2 of the configuration register to a 1). The
power-up takes approximately 4 ms. The part then performs a
conversion and is returned to full power-down. The temperature
value can be read in the full power-down mode since the serial
interface is still powered up.
The ALERT output becomes active when the value in the
temperature value register exceeds the value in the THIGH
register. It is reset when a write operation to the configuration
register sets D3 to a 1 or when the temperature falls below the
value stored in the TLOW register.
POWER VS. THROUGHPUT
The two modes of operation for the AD7414/AD7415 will pro-
duce different power vs. throughput performances. Mode 2 is
the sleep mode of the part and it achieves the optimum power
performance.
The ALERT output requires an external pull-up resistor. This
can be connected to a voltage different from VDD provided the
maximum voltage rating of the ALERT output pin is not
exceeded. The value of the pull-up resistor depends on the
application, but should be as large as possible to avoid excessive
sink currents at the ALERT output, which can heat the chip
and affect the temperature reading.
Mode 1
In this mode, continuous conversions are performed at a rate of
approximately one every 800 ms. Figure 10 shows the times and
currents involved with this mode of operation for a 5 V supply.
At 5 V, the current consumption for the part when converting is
1.1 mA typically and the quiescent current is 188 µA typically.
The conversion time of 25 µs plus power-up time of typically
4 µs contributes 199.3 nW to the overall power dissipation in
the following way:
POWER-ON DEFAULTS
The AD7414/AD7415 always powers up with the following
defaults:
29 µs/800ms × 5 ×1.1mA = 199.3 nW
(
)
(
)
Address pointer register pointing to the temperature value register.
The contribution to the total power dissipated by the remaining
time is 939.96 µW.
T
T
HIGH register loaded with 7Fh.
LOW register loaded with 80h.
799.97ms/800ms × 5 ×1.1µA = 199.3 µW
(
)
(
)
Configuration register loaded with 40h.
Thus the total power dissipated during each cycle is:
199.3 nW + 939.96 µW = 940.16 µW
1.1mA
Note that the AD7415 does not have any THIGH or TLOW registers.
OPERATING MODES
Mode 1
This is the power-on default mode of the AD7414/AD7415. In
this mode, the AD7414/AD7415 does a temperature conversion
every 800 ms and then partially powers down until the next
conversion occurs.
I
DD
188A
29s
800ms
TIME
If a one-shot operation (setting D2 of the configuration register
to a 1) is performed between automatic conversions, a conversion
is initiated right after the write operation. After this conversion,
the part returns to performing a conversion every 800 ms.
Figure 10. Mode 1 Power Dissipation
Mode 2
In this mode, the part is totally powered down. All circuitry
except the serial interface is switched off. The most power efficient
way of operating in this mode is to use the one-shot method. Write
to the configuration register and set the one-shot bit to a 1. The
part will power up in approximately 4 ms and then perform a
conversion. Once the conversion is finished, the device will
power down again until the PD bit in the configuration register
is set to a 0 or the one-shot bit is set to 1. Figure 11 shows the
same timing as Figure 10 in mode 1; a one-shot is initiated every
800 ms. If we take the voltage supply to be 5 V, we can work
out the power dissipation in the following way. The current
consumption for the part when converting is 1.1 mA typically
and the quiescent current is 800 nA typically. The conversion time
of 25 µs plus the power-up time of typically 4 ms contributes
199.3 nW to the overall power dissipation in the following way:
Depending on where a serial port access occurs during a
conversion, that conversion might or might not be aborted. If
the conversion is completed before the part recognizes a serial
port access, the temperature register will be updated with the
new conversion. If the conversion is completed after the part
recognizes a serial port access, the internal logic will prevent the
temperature register from being updated since corrupt data
could be read.
A temperature conversion can start anytime during a serial port
access (other than a one-shot operation), but the result of that
conversion will only be loaded into the temperature register if
the serial port access is not active at the end of the conversion.
Mode 2
The only other mode in which the AD7414/AD7415 operates
is the full power-down mode. This mode is usually used when
temperature measurements are required at a very slow rate. The
power consumption of the part can be greatly reduced in this
mode by writing to the part to go to a full power-down. Full
power-down is initiated right after D7 of the configuration
register is set to 1.
29µs/800 ms × 5 V ×1.1 mA = 199.3 nW
(
)
(
)
The contribution to the total power dissipated by the remaining
time is 3.9 µW.
799.971 ms/800 ms × 5 V × 800 nA = 3.9 mW
(
)
(
)
Thus the total power dissipated during each cycle is:
199.3 nW + 3.9 µW = 940.16 µW
–10–
REV. D
AD7414/AD7415
4
3
1.1mA
I
DD
2
800nA
–40؇C
29s
800ms
TIME
1
0
+40؇C
Figure 11. Mode 2 Power Dissipation
–1
–2
–3
–4
+85؇C
MOUNTING THE AD7414/AD7415
The AD7414/AD7415 can be used for surface or air temperature
sensing applications. If the device is cemented to a surface with
thermally conductive adhesive, the die temperature will be within
about 0.1°C of the surface temperature, due to the device’s low
power consumption. Care should be taken to insulate the back
and leads of the device from the air if the ambient air temperature
is different from the surface temperature being measured.
2.7
3.3
5.0
5.5
SUPPLYVOLTAGE (V)
Figure 13. Typical Temperature Error vs. Supply for One Part
TYPICAL TEMPERATURE ERROR GRAPH
Figure 14 shows the typical temperature error plots for one
device with VDD at 3.3 V and at 5.5 V.
The ground pin provides the best thermal path to the die, so the
temperature of the die will be close to that of the printed circuit
ground track. Care should be taken to ensure that this is in good
thermal contact with the surface being measured.
4
3
As with any IC, the AD7414/AD7415 and its associated wiring
and circuits must be kept free from moisture to prevent leakage
and corrosion, particularly in cold conditions where condensa-
tion is more likely to occur. Water-resistant varnishes and
conformal coatings can be used for protection. The small size
of the AD7414/AD7415 packages allows them to be mounted
inside sealed metal probes, which provide a safe environment
for the device.
2
5.5V
1
0
–1
3.3V
–2
–3
SUPPLY DECOUPLING
The AD7414/AD7415 should at least be decoupled with a 0.1 µF
ceramic capacitor between VDD and GND. This is particularly
important if the AD7414/AD7415 is mounted remote from the
power supply.
–4
–40 –30 –20–10 0 10 20 30 40 50 60 70 80 85 90 100 110 125
TEMPERATURE (؇C)
Figure 14. Typical Temperature Error @ 3.3 V and 5.5 V
TEMPERATURE ACCURACY VS. SUPPLY
The temperature accuracy specifications are guaranteed for
voltage supplies of 3 V and 5.5 V only. Figure 12 gives the typi-
cal performance characteristics of a large sample of parts over
the full voltage range of 2.7 V to 5.5 V. Figure 13 gives the
typical performance characteristics of one part over the full
voltage range of 2.7 V to 5.5 V.
Figure 15 shows a histogram of the temperature error at ambient
temperature (40°C) over approximately 6,000 units. Figure 15
shows that over 70% of the AD7414/AD7415 devices tested
have a temperature error within Ϯ0.3°C.
900
AMBIENTTEMPERATURE = 40؇C
800
700
4
3
600
500
400
2
–40؇C
1
0
+40؇C
300
200
–1
+85؇C
–2
100
–3
–4
0
؊1.08 ؊0.81 ؊0.54 ؊0.27
0
0.27
0.54
0.81 1.08
TEMPERATURE ERROR (؇C)
2.7
3.0
5.5
SUPPLYVOLTAGE (V)
Figure 15. Ambient Temperature Error @ 3 V
Figure 12. Typical Temperature Error vs. Supply
for Large Sample of Parts
REV. D
–11–
AD7414/AD7415
OUTLINE DIMENSIONS
6-Lead Small Outline Transistor Package [SOT-23]
8-Lead Mini Small Outline Package [MSOP]
(RM-8)
(RT-6)
Dimensions shown in millimeters
Dimensions shown in millimeters
2.90 BSC
3.00
BSC
8
5
4
6
1
5
2
4
3
4.90
BSC
3.00
BSC
2.80 BSC
1.60 BSC
1
PIN 1
INDICATOR
PIN 1
0.95 BSC
0.65 BSC
1.90
1.30
1.15
0.90
BSC
1.10 MAX
0.15
0.00
0.80
0.60
0.40
1.45 MAX
8؇
0؇
0.22
0.08
0.38
0.22
0.23
0.08
0.60
0.45
0.30
10؇
4؇
0؇
SEATING
PLANE
COPLANARITY
0.10
0.50
0.30
0.15 MAX
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-187AA
COMPLIANT TO JEDEC STANDARDS MO-178AB
5-Lead Small Outline Transistor Package [SOT-23]
(RT-5)
Dimensions shown in millimeters
2.90 BSC
5
1
4
3
2.80 BSC
1.60 BSC
2
PIN 1
0.95 BSC
1.90
BSC
1.30
1.15
0.90
1.45 MAX
0.22
0.08
10؇
5؇
0؇
0.15 MAX
0.60
0.45
0.30
0.50
0.30
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-178AA
–12–
REV. D
AD7414/AD7415
Revision History
Location
Page
9/04—Data Sheet Changed from REV. C to REV. D.
Changes to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Updated ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
8/03—Data Sheet Changed from REV. B to REV. C.
Change to Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Universal
Updated FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Updated SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Updated ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Updated ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Updated CIRCUIT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Updated TEMPERATURE DATA FORMAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Updated TEMPERATURE VALUE REGISTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Updated Figure 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
11/02—Data Sheet Changed from REV. A to REV. B.
Changes to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
10/02—Data Sheet Changed from REV. 0 to REV. A.
Changes to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Changes to PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Changes to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ORDERING GUIDE updated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Change to Figure 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Added to TYPICAL TEMPERATURE ERROR GRAPH section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Added Figure 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OUTLINE DIMENSIONS updated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
REV. D
–13–
–14–
–15–
–16–
相关型号：
AD7415SRT-0REEL7
Switch/Digital Output Temperature Sensor, DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT, PLASTIC, SOT-23, 5 PIN
ADI
AD7415SRT-1REEL7
Switch/Digital Output Temperature Sensor, DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT, PLASTIC, SOT-23, 5 PIN
ADI
AD7415SRT-2REEL7
Switch/Digital Output Temperature Sensor, DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT, PLASTIC, SOT-23, 5 PIN
ADI
AD7415SRT-3REEL7
Switch/Digital Output Temperature Sensor, DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT, PLASTIC, SOT-23, 5 PIN
ADI
AD7416-7418
10-Bit Digital Temperature Sensor (AD7416) and Single/Four-Channel ADC (AD7417/AD7418)
ADI
AD7416ACHIPS
10-Bit Digital Temperature Sensor (AD7416) and Single/Four-Channel ADC (AD7417/AD7418)
ADI
AD7416AR-REEL
10-Bit Digital Temperature Sensor (AD7416) and Single/Four-Channel ADC (AD7417/AD7418)
ADI
AD7416AR-REEL7
10-Bit Digital Temperature Sensor (AD7416) and Single/Four-Channel ADC (AD7417/AD7418)
ADI
AD7416ARM
10-Bit Digital Temperature Sensor (AD7416) and Single/Four-Channel ADC (AD7417/AD7418)
ADI
©2020 ICPDF网 联系我们和版权申明