AD586LQ/+ [ADI]
IC 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5 V, CDIP8, GLASS SEALED, CERDIP-8, Voltage Reference;型号: | AD586LQ/+ |
厂家: | ADI |
描述: | IC 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5 V, CDIP8, GLASS SEALED, CERDIP-8, Voltage Reference CD 输出元件 |
文件: | 总10页 (文件大小:211K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
High Precision
5 V Reference
a
AD586
FUNCTIO NAL BLO CK D IAGRAM
FEATURES
Laser Trim m ed to High Accuracy:
5.000 V ؎2.0 m V (M Grade)
Trim m ed Tem perature Coefficient:
2 ppm / ؇C m ax, 0؇C to +70؇C (M Grade)
5 ppm / ؇C m ax, –40؇C to +85؇C (B & L Grades)
10 ppm / ؇C m ax, –55؇C to +125؇C (T Grade)
Low Noise, 100 nV/ √Hz
Noise Reduction Capability
Output Trim Capability
MIL-STD-883 Com pliant Versions Available
Industrial Tem perature Range SOICs Available
Output Capable of Sourcing or Sinking 10 m A
P RO D UCT D ESCRIP TIO N
P RO D UCT H IGH LIGH TS
T he AD586 represents a major advance in the state-of-the-art in
monolithic voltage references. Using a proprietary ion-implanted
buried Zener diode and laser wafer trimming of high stability
thin-film resistors, the AD586 provides outstanding perfor-
mance at low cost.
1. Laser trimming of both initial accuracy and temperature
coefficients results in very low errors over temperature with-
out the use of external components. T he AD586M has a
maximum deviation from 5.000 V of ±2.45 mV between
0°C and +70°C, and the AD586T guarantees ±7.5 mV
maximum total error between –55°C and +125°C.
T he AD586 offers much higher performance than most other
5 V references. Because the AD586 uses an industry standard
pinout, many systems can be upgraded instantly with the
AD586. T he buried Zener approach to reference design pro-
vides lower noise and drift than bandgap voltage references. T he
AD586 offers a noise reduction pin which can be used to further
reduce the noise level generated by the buried Zener.
2. For applications requiring higher precision, an optional fine-
trim connection is provided.
3. Any system using an industry standard pinout reference can
be upgraded instantly with the AD586.
4. Output noise of the AD586 is very low, typically 4 µV p-p. A
noise reduction pin is provided for additional noise filtering
using an external capacitor.
T he AD586 is recommended for use as a reference for 8-, 10-,
12-, 14- or 16-bit D/A converters which require an external
precision reference. T he device is also ideal for successive
approximation or integrating A/D converters with up to 14 bits
of accuracy and, in general, can offer better performance than
the standard on-chip references.
5. T he AD586 is available in versions compliant with MIL-
ST D-883. Refer to the Analog Devices Military Products
Databook or current AD586/883B data sheet for detailed
specifications.
T he AD586J, K, L and M are specified for operation from 0°C
to +70°C, the AD586A and B are specified for –40°C to +85°C
operation, and the AD586S and T are specified for –55°C to
+125°C operation. T he AD586J, K, L and M are available in an
8-pin plastic DIP. T he AD586J, K, L, A and B are available in
an 8-pin plastic surface mount small outline (SO) package. T he
AD586J, K, L, S and T are available in an 8-pin cerdip package.
REV. C
Inform ation furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assum ed by Analog Devices for its
use, nor for any infringem ents of patents or other rights of third parties
which m ay result from its use. No license is granted by im plication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norw ood, MA 02062-9106, U.S.A.
Tel: 617/ 329-4700
Fax: 617/ 326-8703
(@ T = + 25°C, V = +15 V unless otherwise noted)
AD586–SPECIFICATIONS
A
IN
AD 586J
AD 586K/A
AD 586L/B
AD 586M
AD 586S
AD 586T
Model
Min Typ Max Min Typ Max Min Typ Max
Min Typ Max Min Typ Max Min Typ Max
Units
Output Voltage
4.980
5.020 4.995
25
5.005 4.9975
5.0025 4.998
5.002 4.990
2
5.010 4.9975
5.0025
10
V
Output Voltage Driftl
0°C to +70°C
15
5
ppm/°C
–55°C to +125°C
20
Gain Adjustment
+6
–2
+6
–2
+6
–2
+6
–2
+6
–2
+6
–2
%
Line Regulation1
10.8 V < +VIN < 36 V
T MIN to T MAX
11.4 V < +VIN < 36 V
T MIN to T MAX
100
100
100
100
±µV/V
µV/mA
150
150
Load Regulationl
Sourcing 0 < IOUT < 10 mA
25°C
100
100
100
100
100
100
100
100
150
150
150
150
T MIN to T MAX
Sinking –10 < IOUT < 0 mA
25°C
400
3
400
400
3
400
3
400
3
400
3
Quiescent Current
2
2
3
2
2
2
2
mA
Power Consumption
30
30
30
30
30
30
mW
Output Noise
0.1 Hz to 10 Hz
4
4
4
4
4
4
µV p-p
Spectral Density, 100 Hz
100
100
100
100
100
100
nV/√Hz
Long-T erm Stability
15
45
15
45
15
45
15
15
45
15
ppm/1000 Hr
mA
Short-Circuit Current-to-Ground
60
60
60
45 60
60
45 60
T emperature Range
Specified Performance2
0
+70
0
–40
+70
+85
+85
0
–40
–40
+70
+85
+85
0
+70 –55
+85 –55
+125 –55
+125 –55
+125 °C
+125
Operating Performance3
NOT ES
–40
+85 –40
–40
1Maximum output voltage drift is guaranteed for all packages and grades. Cerdip packaged parts are also 100°C production tested.
2Lower row shows specified performance for A and B grades.
3T he operating temperature range is defined as the temperatures extremes at which the device will still function. Parts may deviate from their specified performance outside their
specified temperature range.
Specifications subject to change without notice.
Specifications in boldface are rested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min and max specifica-
tions are guaranteed, although only those shown in boldface are tested on all production units unless otherwise specified.
ABSO LUTE MAXIMUM RATINGS*
CO NNECTIO N D IAGRAM
(Top View)
VIN to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V
Power Dissipation (25°C) . . . . . . . . . . . . . . . . . . . . . 500 mW
Storage T emperature . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead T emp (Soldering, 10 sec) . . . . . . . . . . . . . . . . . . +300°C
Package T hermal Resistance
θJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22°C/W
θJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110°C/W
Output Protection: Output safe for indefinite short to ground or
VIN
.
*Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. T his is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
–2–
REV. C
AD586
The following specifications are tested at the die level for AD586JCHIPS. These die are probed at 25؇C
only. (T = +25؇C, V = +15 V unless otherwise noted)
DlE SPECIFlCATIONS
A
IN
AD 586JCH IP S
P aram eter
Min
Typ
Max
Units
Output Voltage
Gain Adjustment
4.980
+6
–2
5.020
V
%
%
Line Regulation
10.8 V < + VIN < 36 V
Load Regulation
100
±µV/V
Sourcing 0 < IOUT < 10 mA
Sinking –10 < IOUT < 0 mA
Quiescent Current
100
400
3
µV/mA
µV/mA
mA
Short-Circuit Current-to-Ground
60
mA
NOT ES
1Both VOUT pads should be connected to the output.
D ie Thickness: T he standard thickness of Analog Devices Bipolar dice is 24 mils ± 2 mils.
D ie D im ensions: T he dimensions given have a tolerance of ±2 mils.
Backing: T he standard backside surface is silicon (not plated). Analog Devices does not
recommend gold-backed dice for most applications.
E dges: A diamond saw is used to separate wafers into dice thus providing perpendicular
edges half-way through the die.
In contrast to scribed dice, this technique provides a more uniform die shape and size. T he
perpendicular edges facilitate handling (such as tweezer pick-up) while the uniform shape
and size simplifies substrate design and die attach.
Top Sur face: T he standard top surface of the die is covered by a layer of glassivation. All
areas are covered except bonding pads and scribe lines.
Sur face Metalization: T he metalization to Analog Devices bipolar dice is aluminum.
Minimum thickness is 10,000Å.
Bonding P ads: All bonding pads have a minimum size of 4 mils by 4 mils. T he passivation
windows have 3.5 mils by 3.5 mils minimum.
O RD ERING GUID E
Initial
Error
Tem perature
Coefficient
Tem perature
Range
P ackage
O ption2
Model1
AD586JN
AD586JQ
AD586JR
20 mV
20 mV
20 mV
5 mV
5 mV
5 mV
2.5 mV
2.5 mV
2 mV
25 ppm/°C
25 ppm/°C
25 ppm/°C
15 ppm/°C
15 ppm/°C
15 ppm/°C
5 ppm/°C
5 ppm/°C
2 ppm/°C
15 ppm/°C
5 ppm/°C
5 ppm/°C
20 ppm/°C
10 ppm/°C
25 ppm/°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
–40°C to +85°C
–40°C to +85°C
0°C to +70°C
–55°C to +125°C
–55°C to +125°C
0°C to +70°C
N-8
Q-8
SO-8
N-8
Q-8
SO-8
N-8
SO-8
N-8
SO-8
SO-8
Q-8
AD586KN
AD586KQ
AD586KR
AD586LN
AD586LR
AD586MN
AD586AR
AD586BR
AD586LQ
AD586SQ
AD586T Q
AD586JCHIPS
5 mV
2.5 mV
2.5 mV
10 mV
2.5 mV
20 mV
Q-8
Q-8
NOT ES
1For details on grade and package offerings screened in accordance with MIL-ST D-883, r efer to the Analog Devices Military
Products Databook or current AD586/883B data sheet.
2N = Plastic DIP; Q = Cerdip; SO = Small Outline IC (SOIC).
CAUTIO N
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD586 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. T herefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. C
–3–
AD586
TH EO RY O F O P ERATIO N
NO ISE P ERFO RMANCE AND RED UCTIO N
T he AD586 consists of a proprietary buried Zener diode refer-
ence, an amplifier to buffer the output and several high stability
thin-film resistors as shown in the block diagram in Figure 1.
T his design results in a high precision monolithic 5 V output
reference with initial offset of 2.0 mV or less. T he temperature
compensation circuitry provides the device with a temperature
coefficient of under 2 ppm/°C.
T he noise generated by the AD586 is typically less than 4 µV
p-p over the 0.1 Hz to 10 Hz band. Noise in a 1 MHz band-
width is approximately 200 µV p-p. T he dominant source of this
noise is the buried Zener which contributes approximately
100 nV/√Hz. In comparison, the op amp’s contribution is negli-
gible. Figure 3 shows the 0.1 Hz to 10 Hz noise of a typical
AD586. T he noise measurement is made with a bandpass filter
made of a 1-pole high-pass filter with a corner frequency at
0.1 Hz and a 2-pole low-pass filter with a corner frequency at
12.6 Hz to create a filter with a 9.922 Hz bandwidth.
Using the bias compensation resistor between the Zener output
and the noninverting input to the amplifier, a capacitor can be
added at the NOISE REDUCT ION pin (Pin 8) to form a low-
pass filter and reduce the noise contribution of the Zener to the
circuit.
If further noise reduction is desired, an external capacitor may
be added between the NOISE REDUCT ION pin and ground as
shown in Figure 2. T his capacitor, combined with the 4 kΩ RS
and the Zener resistances form a low-pass filter on the output of
the Zener cell. A 1 µF capacitor will have a 3 dB point at 12 Hz,
and it will reduce the high frequency (to 1 MHz) noise to about
160 µV p-p. Figure 4 shows the 1 MHz noise of a typical AD586
both with and without a 1 µF capacitor.
Figure 1. AD586 Functional Block Diagram
AP P LYING TH E AD 586
T he AD586 is simple to use in virtually all precision reference
applications. When power is applied to Pin 2 and Pin 4 is
grounded, Pin 6 provides a 5 V output. No external components
are required; the degree of desired absolute accuracy is achieved
simply by selecting the required device grade. T he AD586 re-
quires less than 3 mA quiescent current from an operating sup-
ply of +12 V or +15 V.
Figure 3. 0.1 Hz to 10 Hz Noise
An external fine trim may be desired to set the output level to
exactly 5.000 V (calibrated to a main system reference). System
calibration may also require a reference voltage that is slightly
different from 5.000 V, for example, 5.12 V for binary applica-
tions. In either case, the optional trim circuit shown in Figure 2
can offset the output by as much as 300 mV, if desired, with
minimal effect on other device characteristics.
Figure 4. Effect of 1 µF Noise Reduction Capacitor on
Broadband Noise
TURN-O N TIME
Upon application of power (cold start), the time required for the
output voltage to reach its final value within a specified error
band is defined as the turn-on settling time. T wo components
normally associated with this are: the time for the active circuits
to settle, and the time for the thermal gradients on the chip to
stabilize. Figure 5 shows the turn-on characteristics of the
AD586. It shows the settling to be about 60 µsec to 0.01%.
Note the absence of any thermal tails when the horizontal scale
is expanded to l ms/cm in Figure 5b.
Figure 2. Optional Fine Trim Configuration
–4–
REV. C
AD586
Output turn-on time is modified when an external noise reduc-
tion capacitor is used. When present, this capacitor acts as an
additional load to the internal Zener diode’s current source, re-
sulting in a somewhat longer turn-on time. In the case of a 1 µF
capacitor, the initial turn-on time is approximately 400 ms to
0.01% (see Figure 5c).
D YNAMIC P ERFO RMANCE
T he output buffer amplifier is designed to provide the AD586
with static and dynamic load regulation superior to less com-
plete references.
Many A/D and D/A converters present transient current loads
to the reference, and poor reference response can degrade the
converter’s performance.
Figure 6 displays the characteristics of the AD586 output ampli-
fier driving a 0 mA to 10 mA load.
Figure 5. Turn-On Characteristics
REV. C
–5–
AD586
In some applications, a varying load may be both resistive and
capacitive in nature, or the load may be connected to the
AD586 by a long capacitive cable.
Centigrade; i.e., ppm/°C. However, because of nonlinearities in
temperature characteristics which originated in standard Zener
references (such as “S” type characteristics), most manufactur-
ers have begun to use a maximum limit error band approach to
specify devices. T his technique involves the measurement of the
output at three or more different temperatures to specify an out-
put voltage error band.
Figure 7 displays the output amplifier characteristics driving a
1000 pF, 0 to 10 mA load.
Figure 9 shows the typical output voltage drift for the AD586L
and illustrates the test methodology. T he box in Figure 9 is
bounded on the sides by the operating temperature extremes,
and on the top and the bottom by the maximum and minimum
output voltages measured over the operating temperature range.
T he slope of the diagonal drawn from the lower left to the upper
right corner of the box determines the performance grade of the
device.
Figure 7a. Capacitive Load Transient Response Test Circuit
Figure 7b. Output Response with Capacitive Load
LO AD REGULATIO N
Figure 9. Typical AD586L Tem perature Drift
T he AD586 has excellent load regulation characteristics. Figure
8 shows that varying the load several mA changes the output by
a few µV. T he AD586 has somewhat better load regulation per-
formance sourcing current than sinking current.
Each AD586J, K and L grade unit is tested at 0°C, +25°C and
+70°C. Each AD586SQ and T Q grade unit is tested at –55°C,
+25°C and +125°C. T his approach ensures that the variations
of output voltage that occur as the temperature changes within
the specified range will be contained within a box whose diago-
nal has a slope equal to the maximum specified drift. T he posi-
tion of the box on the vertical scale will change from device to
device as initial error and the shape of the curve vary. T he maxi-
mum height of the box for the appropriate temperature range
and device grade is shown in Figure 10. Duplication of these
results requires a combination of high accuracy and stable tem-
perature control in a test system. Evaluation of the AD586 will
produce a curve similar to that in Figure 9, but output readings
may vary depending on the test methods and equipment utilized.
D EVICE
GRAD E
MAXIMUM O UTP UT CH ANGE
(m V)
Figure 8. Typical Load Regulation Characteristics
0؇C TO +70؇C
–40؇C TO +85؇C –55؇C TO +125؇C
TEMP ERATURE P ERFO RMANCE
AD586J
AD586K
AD586L
AD586M
AD586A
AD586B
AD586S
AD586T
8.75
5.25
1.75
0.70
T he AD586 is designed for precision reference applications
where temperature performance is critical. Extensive tempera-
ture testing ensures that the device’s high level of performance is
maintained over the operating temperature range.
3.12
9.37
18.00
9.00
Some confusion exists in the area of defining and specifying ref-
erence voltage error over temperature. Historically, references
have been characterized using a maximum deviation per degree
Figure 10. Maxim um Output Change in m V
–6–
REV. C
AD586
NEGATIVE REFERENCE VO LTAGE FRO M AN AD 586
T he AD586 can be used to provide a precision –5.000 V output
as shown in Figure 11. T he VIN pin is tied to at least a +6 V
supply, the output pin is grounded, and the AD586 ground pin
is connected through a resistor, RS, to a –15 V supply. T he –5 V
output is now taken from the ground pin (Pin 4) instead of
VOUT . It is essential to arrange the output load and the supply
resistor RS so that the net current through the AD586 is be-
tween 2.5 mA and 10.0 mA. T he temperature characteristics
and long-term stability of the device will be essentially the same
as that of a unit used in the standard +5 V output configuration.
Figure 13. AD586 as a 5 V Reference for a CMOS
Dual DAC
STACKED P RECISIO N REFERENCES FO R
MULTIP LE VO LTAGES
Often, a design requires several reference voltages. T hree
AD586s can be stacked, as shown in Figure 14, to produce
+5.000 V, +10.000 V, and +15.000 V outputs. T his scheme
can be extended to any number of AD586s as long as the
maximum load current is not exceeded. T his design pro-
vides the additional advantage of improved line regulation
on the +5.0 V output. Changes in VIN of +18 V to +50 V
produces an output change that is below the noise level of
the references.
Figure 11. AD586 as a Negative 5 V Reference
USING TH E AD 586 WITH CO NVERTERS
T he AD586 is an ideal reference for a wide variety of 8-, 12-,
14- and 16-bit A/D and D/A converters. Several representative
examples follow.
5 V REFERENCE WITH MULTIP LYING CMO S D /A O R
A/D CO NVERTERS
T he AD586 is ideal for applications with 10- and 12-bit multi-
plying CMOS D/A converters. In the standard hookup, as
shown in Figure 12, the AD586 is paired with the AD7545
12-bit multiplying DAC and the AD711 high-speed BiFET Op
Amp. T he amplifier DAC configuration produces a unipolar
0 V to –5 V output range. Bipolar output applications and other
operating details can be found on the individual product data
sheets.
Figure 14. Multiple AD586s Stacked for Precision 5 V,
10 V and 15 V Outputs
Figure 12. Low-Power 12-Bit CMOS DAC Application
T he AD586 can also be used as a precision reference for mul-
tiple DACs. Figure 13 shows the AD586, the AD7628 dual
DAC and the AD712 dual op amp hooked up for single supply
operation to produce 0 V to –5 V outputs. Because both DACs
are on the same die and share a common reference and output
op amps, the DAC outputs will exhibit similar gain T Cs.
REV. C
–7–
AD586
P RECISIO N CURRENT SO URCE
T he design of the AD586 allows it to be easily configured as a
current source. By choosing the control resistor RC in Figure 15,
you can vary the load current from the quiescent current (2 mA
typically) to approximately 10 mA. T he compliance voltage of
this circuit varies from about +5 V to +21 V depending upon
the value of VIN
.
Figure 15. Precision Current Source
P RECISIO N H IGH CURRENT SUP P LY
capacitor is required only if the load has a significant capacitive
component. If the load is purely resistive, improved high-
frequency supply rejection results can be obtained by removing
the capacitor.
For higher currents, the AD586 can easily be connected to a
power PNP or power Darlington PNP device. T he circuit in
Figure 16 can deliver up to 4 amps to the load. T he 0.1 µF
Figure 16a. Precision High-Current Current Source
Figure 16b. Precision High-Current Voltage Source
O UTLINE D IMENSIO NS
D imensions shown in inches and (mm.)
Mini-D IP (N-8) P ackage
Cer dip (Q -8) P ackage
Sm all O utline (R-8) P ackage
–8–
REV. C
Analog Products -- AD586
Page 1 of 2
Package/Price Information
For detailed packaging information, please select the Datasheets button.
High Precision 5 V Reference
Package
Description
Pin
Count
Temperature
Range
Price*
(100-499)
Model
Status
5962-8982401PA
5962-8982402PA
AD586AR
PRODUCTION CERDIP GLASS SEAL
PRODUCTION CERDIP GLASS SEAL
PRODUCTION STD S.O. PKG (SOIC)
PRODUCTION STD S.O. PKG (SOIC)
PRODUCTION STD S.O. PKG (SOIC)
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
MILITARY
MILITARY
$12.98
$23.72
COMMERCIAL $5.10
COMMERCIAL $7.10
AD586BR
AD586BR-REEL
INDUSTRIAL
INDUSTRIAL
-
-
AD586BR-REEL7 PRODUCTION STD S.O. PKG (SOIC)
AD586JCHIPS
AD586JN
PRODUCTION CHIPS/DIE SALES
PRODUCTION PLASTIC/EPOXY DIP
PRODUCTION CERDIP GLASS SEAL
COMMERCIAL $2.60
COMMERCIAL $2.91
COMMERCIAL $3.07
AD586JQ
AD586JQ/+
AD586JR
OBSOLETE
CERDIP GLASS SEAL
COMMERCIAL
-
PRODUCTION STD S.O. PKG (SOIC)
PRODUCTION STD S.O. PKG (SOIC)
PRODUCTION STD S.O. PKG (SOIC)
PRODUCTION PLASTIC/EPOXY DIP
PRODUCTION CERDIP GLASS SEAL
COMMERCIAL $3.07
AD586JR-REEL
AD586JR-REEL7
AD586KN
COMMERCIAL
COMMERCIAL
-
-
COMMERCIAL $3.74
COMMERCIAL $4.06
AD586KQ
AD586KQ/+
AD586KR
OBSOLETE
CERDIP GLASS SEAL
COMMERCIAL
-
PRODUCTION STD S.O. PKG (SOIC)
PRODUCTION STD S.O. PKG (SOIC)
COMMERCIAL $4.06
AD586KR-REEL
COMMERCIAL
COMMERCIAL
-
-
AD586KR-REEL7 PRODUCTION STD S.O. PKG (SOIC)
AD586LN
PRODUCTION PLASTIC/EPOXY DIP
PRODUCTION CERDIP GLASS SEAL
COMMERCIAL $5.24
COMMERCIAL $7.10
AD586LQ
AD586LQ/+
AD586LR
OBSOLETE
CERDIP GLASS SEAL
COMMERCIAL
-
PRODUCTION STD S.O. PKG (SOIC)
PRODUCTION STD S.O. PKG (SOIC)
PRODUCTION STD S.O. PKG (SOIC)
PRODUCTION PLASTIC/EPOXY DIP
PRODUCTION CHIPS/DIE SALES
COMMERCIAL $5.57
AD586LR-REEL
AD586LR-REEL7
AD586MN
COMMERCIAL
COMMERCIAL
-
-
COMMERCIAL $6.01
MILITARY $6.33
AD586SCHIPS
file://F:\export\projects\bitting2\imaging\BITTING\mail_pdf\200\models7.html
5/8/01
Analog Products -- AD586
Page 2 of 2
AD586SQ
PRODUCTION CERDIP GLASS SEAL
OBSOLETE CERDIP GLASS SEAL
PRODUCTION CERDIP GLASS SEAL
8
8
8
MILITARY
MILITARY
MILITARY
$8.35
AD586SQ/883B
AD586TQ
-
$17.96
* This price is provided for budgetary purposes as recommended list price in U.S. Dollars per unit the
stated volume. Pricing displayed for Evaluation Boards and Kits is based on 1-piece pricing. View
Pricing and Availability (currently available to North American customers) for further information.
file://F:\export\projects\bitting2\imaging\BITTING\mail_pdf\200\models7.html
5/8/01
相关型号:
AD586MNZ
1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5 V, PDIP8, LEAD FREE, PLASTIC, MO-095AA, DIP-8
ROCHESTER
©2020 ICPDF网 联系我们和版权申明