AD5405YCPZ [ADI]
Dual 12-Bit, High Bandwidth, Multiplying DAC with 4-Quadrant Resistors and Parallel Interface; 双通道12位,高带宽,乘法DAC,四象限电阻和并行接口型号: | AD5405YCPZ |
厂家: | ADI |
描述: | Dual 12-Bit, High Bandwidth, Multiplying DAC with 4-Quadrant Resistors and Parallel Interface |
文件: | 总25页 (文件大小:753K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Dual 12-Bit, High Bandwidth, Multiplying DAC with
4-Quadrant Resistors and Parallel Interface
AD5405
GENERAL DESCRIPTION
FEATURES
10 MHz multiplying bandwidth
On-chip 4-quadrant resistors allow flexible output ranges
INL of 1 LSB
40-lead LFCSP package
2.5 V to 5.5 V supply operation
10 V reference input
21.3 MSPS update rate
Extended temperature range: −40°C to 125°C
4-quadrant multiplication
Power-on reset
0.5 μA typical current consumption
Guaranteed monotonic
The AD54051 is a CMOS, 12-bit, dual-channel, current output
digital-to-analog converter (DAC). This device operates from a
2.5 V to 5.5 V power supply, making it suited to battery-powered
and other applications.
As a result of manufacture with a CMOS submicron process, the
device offers excellent 4-quadrant multiplication characteristics,
with large signal multiplying bandwidths of up to 10 MHz.
The applied external reference input voltage (VREF) determines
the full-scale output current. An integrated feedback resistor (RFB)
provides temperature tracking and full-scale voltage output when
combined with an external I-to-V precision amplifier. This device
also contains the 4-quadrant resistors necessary for bipolar
operation and other configuration modes.
Readback function
APPLICATIONS
Portable battery-powered applications
Waveform generators
Analog processing
Instrumentation applications
Programmable amplifiers and attenuators
Digitally controlled calibration
Programmable filters and oscillators
Composite video
This DAC uses data readback, allowing the user to read the
contents of the DAC register via the DB pins. On power-up, the
internal register and latches are filled with 0s, and the DAC
outputs are at zero scale.
The AD5405 has a 6 mm × 6 mm, 40-lead LFCSP package.
1 U.S. Patent Number 5,689,257.
Ultrasound
Gain, offset, and voltage trimming
FUNCTIONAL BLOCK DIAGRAM
V
A
R3A
R2_3A
R2A
REF
R1A
R3
2R
R2
2R
R1
2R
RFB
2R
AD5405
V
R
A
DD
FB
DATA
INPUTS
DB0
I
1A
2A
OUT
INPUT
BUFFER
12-BIT
R-2R DAC A
LATCH
DB11
I
OUT
DAC A/B
CONTROL
LOGIC
CS
R/W
I
I
1B
2B
OUT
12-BIT
R-2R DAC B
LATCH
OUT
LDAC
R
B
FB
POWER-ON
RESET
GND
CLR
R1
2R
RFB
2R
R3
2R
R2
2R
R3B
R2_3B
R2B
V
B R1B
REF
Figure 1.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
© 2009 Analog Devices, Inc. All rights reserved.
IMPORTANT LINKS for the AD5405*
Last content update 10/02/2013 03:07 pm
PARAMETRIC SELECTION TABLES
DESIGN COLLABORATION COMMUNITY
Find Similar Products By Operating Parameters
Data Converters: Overview of AD54xx Devices
AD5415 Dual 12-Bit, High Bandwidth, Multiplying DAC with 4
Quadrant Resistors and Serial Interface
Collaborate Online with the ADI support team and other designers
about select ADI products.
AD5449 Dual 12-Bit, High Bandwidth Multiplying DAC with Serial
Interface
Follow us on Twitter: www.twitter.com/ADI_News
Like us on Facebook: www.facebook.com/AnalogDevicesInc
DOCUMENTATION
DESIGN SUPPORT
AN-1085: Multiplying DACs—AC/Arbitrary Reference Applications
Submit your support request here:
Linear and Data Converters
AN-912: Driving a Center-Tapped Transformer with a Balanced
Current-Output DAC
Embedded Processing and DSP
AN-320A: CMOS Multiplying DACs and Op Amps Combine to Build
Programmable Gain Amplifier, Part 1
Telephone our Customer Interaction Centers toll free:
Americas:
Europe:
China:
1-800-262-5643
00800-266-822-82
4006-100-006
1800-419-0108
8-800-555-45-90
AN-320B: CMOS Multiplying DACs and Op Amps Combine to Build
Programmable Gain Amplifiers, Part 2
AN-137: A Digitally Programmable Gain and Attenuation Amplifier
Design
India:
Russia:
Digital to Analog Converters ICs Solutions Bulletin
4-Quadrant Multiplying D/A Converters
Quality and Reliability
Lead(Pb)-Free Data
EVALUATION KITS & SYMBOLS & FOOTPRINTS
View the Evaluation Boards and Kits page for documentation and
purchasing
SAMPLE & BUY
AD5405
Symbols and Footprints
View Price & Packaging
Request Evaluation Board
Request Samples
Check Inventory & Purchase
Find Local Distributors
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet.
Note: Dynamic changes to the content on this page (labeled 'Important Links') does not
constitute a change to the revision number of the product data sheet.
This content may be frequently modified.
AD5405
TABLE OF CONTENTS
Specifications..................................................................................... 3
Timing Characteristics ................................................................ 5
Absolute Maximum Ratings............................................................ 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 8
Terminology .................................................................................... 13
General Description....................................................................... 14
DAC Section................................................................................ 14
Circuit Operation ....................................................................... 14
Single-Supply Applications ....................................................... 15
Adding Gain................................................................................ 15
Divider or Programmable Gain Element................................ 16
Reference Selection .................................................................... 16
Amplifier Selection .................................................................... 16
Parallel Interface......................................................................... 18
Microprocessor Interfacing....................................................... 18
PCB Layout and Power Supply Decoupling ........................... 19
Evaluation Board for the DACs................................................ 19
Power Supplies for the Evaluation Board................................ 19
Overview of AD54xx Devices....................................................... 22
Outline Dimensions....................................................................... 23
Ordering Guide .......................................................................... 23
REVISION HISTORY
12/09—Rev. A to Rev. B
Changes to Figure 1.......................................................................... 1
Changes to Table 2 and Figure 2..................................................... 5
Changes to Table 4 and Figure 4..................................................... 7
Updated Outline Dimensions....................................................... 23
Changes to Ordering Guide .......................................................... 23
7/05—Rev. 0 to Rev. A
Changed Pin DAC A/B to DAC /B................................Universal
A
Changes to Features List.................................................................. 1
Changes to Specifications................................................................ 3
Changes to Timing Characteristics................................................ 5
Change to Absolute Maximum Ratings......................................... 6
Change to Figure 7 and Figure 8..................................................... 8
Change to Figure 12 ......................................................................... 9
Change to Figure 26 Through Figure 28 ..................................... 11
Changes to General Description Section .................................... 14
Change to Figure 31 ....................................................................... 14
Changes to Table 5 Through Table 10.......................................... 14
Changes to Figure 34 and Figure 35............................................. 15
Changes to Figure 36 and Figure 37............................................. 16
Changes to Microprocessor Interfacing Section ........................ 18
Added Figure 38 Through Figure 40............................................ 18
Change to Power Supplies for the Evaluation Board Section... 19
Updated Outline Dimensions....................................................... 23
Changes to Ordering Guide .......................................................... 23
7/04—Revision 0: Initial Version
Rev. B | Page 2 of 24
AD5405
SPECIFICATIONS1
VDD = 2.5 V to 5.5 V, VREF = 10 V, IOUT2 = 0 V. Temperature range for Y version: −40°C to +125°C. All specifications TMIN to TMAX, unless
otherwise noted. DC performance is measured with OP177, and ac performance is measured with AD8038, unless otherwise noted.
Table 1.
Parameter
Min
Typ Max
Unit
Conditions
STATIC PERFORMANCE
Resolution
Relative Accuracy
12
1
Bits
LSB
Differential Nonlinearity
Gain Error
Gain Error Temperature Coefficient
Bipolar Zero-Code Error
Output Leakage Current
−1/+2
25
LSB
mV
ppm FSR/°C
mV
nA
nA
Guaranteed monotonic
Data = 0x0000, TA = 25°C, IOUT
5
25
1
15
1
Data = 0x0000, TA = −40°C to +125°C, IOUT1
REFERENCE INPUT
Reference Input Range
VREFA, VREFB Input Resistance
VREFA-to-VREFB Input Resistance
Mismatch
10
10
1.6
V
kΩ
%
8
13
2.5
Input resistance TC = −50 ppm/°C
Typ = 25°C, max = 125°C
R1, RFB Resistance
R2, R3 Resistance
R2-to-R3 Resistance Mismatch
Input Capacitance
Code 0
17
17
20
20
25
25
kΩ
kΩ
%
Input resistance TC = −50 ppm/°C
Input resistance TC = −50 ppm/°C
Typ = 25°C, max = 125°C
0.06 0.18
3.5
3.5
pF
pF
Code 4095
DIGITAL INPUTS/OUTPUT
Input High Voltage, VIH
1.7
1.7
V
V
VDD = 3.6 V to 5.5 V
VDD = 2.5 V to 3.6 V
Input Low Voltage, VIL
Output High Voltage, VOH
Output Low Voltage, VOL
0.8
0.7
V
V
V
V
V
V
μA
pF
VDD = 2.7 V to 5.5 V
VDD = 2.5 V to 2.7 V
VDD = 4.5 V to 5.5 V, ISOURCE = 200 μA
VDD = 2.5 V to 3.6 V, ISOURCE = 200 μA
VDD = 4.5 V to 5.5 V, ISINK = 200 μA
VDD = 2.5 V to 3.6 V, ISINK = 200 μA
VDD − 1
VDD − 0.5
0.4
0.4
1
Input Leakage Current, IIL
Input Capacitance
4
10
DYNAMIC PERFORMANCE
Reference-Multiplying BW
Output Voltage Settling Time
10
MHz
VREF = 3.5 V p-p, DAC loaded all 1s
RLOAD = 100 Ω, CLOAD = 15 pF, VREF = 10 V
DAC latch alternately loaded with 0s and 1s
Measured to 1 mV of FS
Measured to 4 mV of FS
Measured to 16 mV of FS
Digital Delay
10% to 90% Settling Time
Digital-to-Analog Glitch Impulse
Multiplying Feedthrough Error
80
35
30
20
15
3
120
70
60
40
30
ns
ns
ns
ns
ns
nV-sec
Interface time delay
Rise and fall times
1 LSB change around major carry, VREF = 0 V
DAC latch loaded with all 0s, VREF = 3.5 V
1 MHz
10 MHz
DAC latches loaded with all 0s
DAC latches loaded with all 1s
70
48
17
30
dB
dB
pF
pF
Output Capacitance
12
25
Rev. B | Page 3 of 24
AD5405
Parameter
Min
Typ Max
Unit
Conditions
Digital Feedthrough
1
nV-sec
Feedthrough to DAC output with CS high and
alternate loading of all 0s and all 1s
@ 1 kHz
VREF = 3. 5 V p-p, all 1s loaded, f = 1 kHz
Clock = 10 MHz, VREF = 3.5 V
Output Noise Spectral Density
Analog THD
Digital THD
25
81
nV/√Hz
dB
100 kHz fOUT
50 kHz fOUT
61
66
dB
dB
SFDR Performance (Wideband)
Clock = 10 MHz
500 kHz fOUT
VREF = 3.5 V
55
63
65
dB
dB
dB
100 kHz fOUT
50 kHz fOUT
Clock = 25 MHz
500 kHz fOUT
100 kHz fOUT
50
60
62
dB
dB
dB
50 kHz fOUT
SFDR Performance (Narrow Band)
Clock = 10 MHz
500 kHz fOUT
VREF = 3.5 V
73
80
87
dB
dB
dB
100 kHz fOUT
50 kHz fOUT
Clock = 25 MHz
500 kHz fOUT
100 kHz fOUT
70
75
80
dB
dB
dB
50 kHz fOUT
Intermodulation Distortion
f1 = 40 kHz, f2 = 50 kHz
f1 = 40 kHz, f2 = 50 kHz
POWER REQUIREMENTS
Power Supply Range
IDD
VREF = 3.5 V
Clock = 10 MHz
Clock = 25 MHz
72
65
dB
dB
2.5
5.5
0.7
10
V
μA
μA
%/%
TA = 25°C, logic inputs = 0 V or VDD
TA = −40°C to +125°C, logic inputs = 0 V or VDD
∆VDD = 5%
0.5
Power Supply Sensitivity
0.001
1 Guaranteed by design and characterization, not subject to production test.
Rev. B | Page 4 of 24
AD5405
TIMING CHARACTERISTICS
All input signals are specified with tr = tf = 1 ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. VDD = 2.5 V to 5.5 V,
REF = 10 V, IOUT2 = 0 V, temperature range for Y version: −40°C to +125°C. All specifications TMIN to TMAX, unless otherwise noted.
V
Table 2.
Parameter1
Limit at TMIN, TMAX
Unit
Conditions/Comments
Write Mode
t1
0
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns typ
ns typ
ns typ
ns typ
R/W-to-CS setup time
R/W-to-CS hold time
CS low time
t2
0
t3
10
10
0
6
0
t4
t5
t6
t7
Address setup time
Address hold time
Data setup time
Data hold time
R/W high to CS low
CS min high time
t8
5
t9
7
t14
10
12
10
10
CS rising-to-LDAC falling time
LDAC pulse width
t15
t16
CS rising-to-LDAC rising time
LDAC falling-to-CS rising time
t17
Data Readback Mode
t10
t11
t12
0
0
5
35
5
ns typ
ns typ
ns typ
ns max
ns typ
ns max
MSPS
Address setup time
Address hold time
Data access time
t13
Bus relinquish time
10
21.3
Update Rate
Consists of CS min high time, CS low time, and output voltage settling time
1 Guaranteed by design and characterization, not subject to production test.
t8
t2
t2
t1
R/W
CS
t9
t3
t4
t11
t10
t5
DACA/DACB
DATA
t6
t12
t13
t7
DATA VALID
DATA VALID
t14
t15
LDAC1
LDAC2
t17
t16
1ASYNCHRONOUS LDAC UPDATE MODE.
2SYNCHRONOUS LDAC UPDATE MODE.
Figure 2. Timing Diagram
I
200
μ
A
OL
V
+ V
2
TO
OUTPUT
PIN
OH (MIN)
OL (MAX)
C
50pF
L
I
200
μ
A
OH
Figure 3. Load Circuit for Data Timing Specifications
Rev. B | Page 5 of 24
AD5405
ABSOLUTE MAXIMUM RATINGS
Transient currents of up to 100 mA do not cause SCR latch-up.
TA = 25°C, unless otherwise noted.
Table 3.
Parameter
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rating
VDD to GND
VREFA, VREFB, RFBA, RFBB to GND
IOUT1, IOUT2 to GND
Logic Inputs and Output1
Operating Temperature Range
Automotive (Y Version)
Storage Temperature Range
Junction Temperature
−0.3 V to +7 V
−12 V to +12 V
−0.3 V to +7 V
−0.3 V to VDD + 0.3 V
−40°C to +125°C
−65°C to +150°C
150°C
40-lead LFCSP, θJA Thermal Impedance
Lead Temperature, Soldering (10 sec)
IR Reflow, Peak Temperature (<20 sec)
30°C/W
300°C
235°C
1
LDAC CS
W
Overvoltages at DBx,
,
, and R/ are clamped by internal diodes.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. B | Page 6 of 24
AD5405
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
R1A
R2A
R2_3A
1
2
3
4
5
6
7
8
9
30 R1B
29 R2B
28 R2_3B
27 R3B
PIN 1
INDICATOR
R3A
V
A
REF
26 V
25 V
B
AD5405
REF
DD
DGND
LDAC
DAC A/B
NC
TOP VIEW
(Not to Scale)
24 CLR
23 R/W
22 CS
DB11 10
21 DB0
NOTES
1. NC = NO CONNECT.
2. EXPOSED PAD MUST BE CONNECTED TO GROUND.
Figure 4. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
Description
1 to 4
R1A, R2B,
R2_3B, R3A
DAC A 4-Quadrant Resistors. Allow a number of configuration modes, including bipolar operation with
minimum of external components.
5, 26
6
7
VREFA, VREF
DGND
LDAC
B
DAC Reference Voltage Input Terminals.
Digital Ground Pin.
Load DAC Input. Allows asynchronous or synchronous updates to the DAC output. The DAC is
asynchronously updated when this signal goes low. Alternatively, if this line is held permanently low, an
automatic or synchronous update mode is selected whereby the DAC is updated on the rising edge of CS.
8
A
Selects DAC A or B. Low selects DAC A, and high selects DAC B.
DAC /B
9, 34 to 37
10 to 21
22
NC
Not internally connected.
Parallel Data Bits 11 through 0.
Chip Select Input. Active low. Used in conjunction with R/W to load parallel data to the input latch or to
read data from the DAC register. Edge sensitive; when pulled high, the DAC data is latched.
Read/Write. When low, used in conjunction with CS to load parallel data. When high, used in conjunction
with CS to read back contents of DAC register.
DB11 to DB0
CS
23
R/W
24
CLR
VDD
Active Low Control Input. Clears DAC output and input and DAC registers.
25
Positive Power Supply Input. These parts can be operated from a supply of 2.5 V to 5.5 V.
27 to 30
R3B, R2_3B,
R2B, R1B
DAC B 4-Quadrant Resistors. Allow a number of configuration modes, including bipolar operation with a
minimum of external components.
31, 40
32
RFBB, RFBA
IOUT2B
External Amplifier Output.
DAC A Analog Ground. This pin typically should be tied to the analog ground of the system, but can be
biased to achieve single-supply operation.
33
38
39
IOUT1B
IOUT1A
IOUT2A
DAC B Current Outputs.
DAC A Current Outputs.
DAC A Analog Ground. This pin typically should be tied to the analog ground of the system, but can be
biased to achieve single-supply operation.
EPAD
Exposed pad must be connected to ground.
Rev. B | Page 7 of 24
AD5405
TYPICAL PERFORMANCE CHARACTERISTICS
1.0
–0.40
–0.45
–0.50
–0.55
–0.60
–0.65
–0.70
T
= 25°C
A
T
V
V
= 25°C
A
0.8
0.6
V
= 5V
DD
= 10V
REF
= 5V
DD
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1.0
MIN DNL
0
0
2
500
1000
1500
2000
2500
3000
3500
4000
4000
10
2
3
4
5
6
7
8
9
10
CODE
REFERENCE VOLTAGE
Figure 5. INL vs. Code (12-Bit DAC)
Figure 8. DNL vs. Reference Voltage
1.0
0.8
5
T
V
V
= 25°C
A
4
3
= 10V
REF
= 5V
V
= 5V
DD
DD
0.6
0.4
2
0.2
1
0
0
V
= 2.5V
DD
–0.2
–0.4
–0.6
–0.8
–1.0
–1
–2
–3
–4
–5
V
= 10V
REF
500
1000
1500
2000
2500
3000
3500
–60 –40 –20
0
20
40
60
80
100 120 140
CODE
TEMPERATURE (°C)
Figure 6. DNL vs. Code (12-Bit DAC)
Figure 9. Gain Error vs. Temperature
0.6
0.5
0.4
0.3
0.2
0.1
0
8
7
6
5
4
3
2
1
0
T
= 25°C
A
MAX INL
V
= 5V
DD
T
V
= 25°C
= 5V
A
DD
MIN INL
–0.1
–0.2
–0.3
V
= 3V
DD
V
= 2.5V
DD
3
4
5
6
7
8
9
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
0.5
1.0
REFERENCE VOLTAGE
INPUT VOLTAGE (V)
Figure 7. INL vs. Reference Voltage
Figure 10. Supply Current vs. Logic Input Voltage
Rev. B | Page 8 of 24
AD5405
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
6
0
–6
T
= 25°C
ALL ON
DB11
DB10
DB9
DB8
DB7
A
LOADING
ZS TO FS
–12
–18
–24
–30
–36
–42
–48
–54
–60
–66
–72
–78
–84
–90
–96
–102
I
I
1 V = 5V
DD
OUT
DB6
DB5
DB4
DB3
DB2
DB1
DB0
1 V = 3V
DD
OUT
T
V
= 25°C
DD
= ±3.5V
= 1.8pF
A
= 5V
V
REF
C
ALL OFF
COMP
AMP = AD8038
1
10
100
1k
10k
100k
1M 10M 100M
–40
–20
0
20
40
60
80
100
120
FREQUENCY (Hz)
TEMPERATURE (°C)
Figure 14. Reference Multiplying Bandwidth vs. Frequency and Code
Figure 11. IOUT1 Leakage Current vs. Temperature
0.2
0
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
V
= 5V
DD
ALL 0s
ALL 1s
–0.2
–0.4
V
= 2.5V
DD
ALL 1s
ALL 0s
T
= 25°C
A
–0.6
–0.8
V
V
= 5V
DD
=
±
3.5V
REF
C
= 1.8pF
COMP
AMP = AD8038
1
10 100
1k
10k
100k
1M
10M
100M
–60 –40 –20
0
20
40
60
80
100 120 140
FREQUENCY (Hz)
TEMPERATURE (°C)
Figure 15. Reference Multiplying Bandwidth—All 1s Loaded
Figure 12. Supply Current vs. Temperature
14
12
10
8
3
T
V
= 25°C
A
T
= 25°C
A
= 5V
DD
LOADING ZS TO FS
V
= 5V
0
DD
–3
–6
–9
6
V
V
= 3V
DD
DD
4
V
V
V
V
V
= ±2V, AD8038 C 1.47pF
REF
REF
REF
REF
REF
C
= 2.5V
= ±2V, AD8038 C 1pF
C
= ±0.15V, AD8038 C 1pF
C
2
= ±0.15V, AD8038 C 1.47pF
C
= ±3.51V, AD8038 C 1.8pF
C
0
10k
100k
1M
10M
100M
1
10
100
1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 16. Reference Multiplying Bandwidth vs. Frequency
and Compensation Capacitor
Figure 13. Supply Current vs. Update Rate
Rev. B | Page 9 of 24
AD5405
–60
–65
–70
–75
–80
–85
–90
0.045
0x7FF TO 0x800
T
V
= 25°C
= 0V
T = 25°C
A
A
0.040
0.035
0.030
0.025
0.020
0.015
0.010
0.005
0
V
= 3V
REF
AMP = AD8038
= 1.8pF
DD
V
= 5V
V
= 3.5V p-p
DD
REF
C
COMP
V
= 3V
DD
0x800 TO 0x7FF
= 3V
V
DD
–0.005
–0.010
V
= 5V
DD
0
20
40
60
80
100 120 140 160 180 200
TIME (ns)
1
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 20. THD and Noise vs. Frequency
Figure 17. Midscale Transition, VREF = 0 V
100
80
60
40
20
0
–1.68
–1.69
–1.70
–1.71
–1.72
–1.73
–1.74
–1.75
–1.76
–1.77
T
V
= 25°C
= 3.5V
A
0x7FF TO 0x800
= 5V
MCLK = 1MHz
REF
AMP = AD8038
= 1.8pF
V
DD
C
COMP
MCLK = 200kHz
MCLK = 0.5MHz
V
= 3V
DD
V
= 5V
V
DD
= 3V
DD
T
V
= 25°C
= 3.5V
A
REF
AMP = AD8038
0x800 TO 0x7FF
20 40 60
0
20
40
60
80
100 120 140 160 180 200
0
80
100 120 140 160 180 200
TIME (ns)
fOUT (kHz)
Figure 18. Midscale Transition, VREF = 3.5 V
Figure 21. Wideband SFDR vs. fOUT Frequency
20
0
90
80
70
60
50
40
30
20
10
0
T
V
= 25°C
A
= 3V
DD
AMP = AD8038
MCLK = 5MHz
MCLK = 10MHz
–20
–40
–60
–80
–100
–120
FULL SCALE
ZERO SCALE
MCLK = 25MHz
T
V
= 25°C
= 3.5V
A
REF
AMP = AD8038
1
100
1k
10k
100k
1M
10M
10
0
100 200 300 400 500 600 700 800 900 1000
fOUT (kHz)
FREQUENCY (Hz)
Figure 19. Power Supply Rejection Ratio vs. Frequency
Figure 22. Wideband SFDR vs. fOUT Frequency
Rev. B | Page 10 of 24
AD5405
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
T
V
= 25°C
T = 25°C
A
DD
AMP = AD8038
65k CODES
A
= 5V
V
= 3V
DD
AMP = AD8038
65k CODES
0
2
4
6
8
10
12
250 300 350 400 450 500 550 600 650 700 750
FREQUENCY (MHz)
FREQUENCY (kHz)
Figure 23. Wideband SFDR, fOUT = 100 kHz, Clock = 25 MHz
Figure 26. Narrow-Band Spectral Response, fOUT = 500 kHz, Clock = 25 MHz
20
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
T
V
= 25°C
T = 25°C
A
DD
AMP = AD8038
65k CODES
A
= 5V
V
= 3V
DD
AMP = AD8038
65k CODES
0
–20
–40
–60
–80
–100
–120
50
60
70
80
90
100 110 120 130 140 150
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
FREQUENCY (kHz)
FREQUENCY (MHz)
Figure 27. Narrow-Band SFDR, fOUT = 100 kHz, Clock = 25 MHz
Figure 24. Wideband SFDR, fOUT = 500 kHz, Clock = 10 MHz
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
T = 25°C
A
DD
AMP = AD8038
65k CODES
T
V
= 25°C
A
V
= 3V
= 5V
DD
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
AMP = AD8038
65k CODES
70
75
80
85
90
95
100 105 110 115 120
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
FREQUENCY (kHz)
FREQUENCY (MHz)
Figure 28. Narrow-Band IMD, fOUT = 90 kHz, 100 kHz, Clock = 10 MHz
Figure 25. Wideband SFDR, fOUT = 50 kHz, Clock = 10 MHz
Rev. B | Page 11 of 24
AD5405
300
250
200
150
100
50
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
T
= 25°C
T
V
= 25°C
DD
A
A
ZERO SCALE LOADED TO DAC
MIDSCALE LOADED TO DAC
FULL SCALE LOADED TO DAC
AMP = AD8038
= 5V
AMP = AD8038
65k CODES
0
–100
0
100
1k
10k
FREQUENCY (Hz)
100k
50
100
150
200
250
300
350
400
FREQUENCY (kHz)
Figure 29. Wideband IMD, fOUT = 90 kHz, 100 kHz, Clock = 25 MHz
Figure 30. Output Noise Spectral Density
Rev. B | Page 12 of 24
AD5405
TERMINOLOGY
Relative Accuracy (Endpoint Nonlinearity)
Multiplying Feedthrough Error
A measure of the maximum deviation from a straight line
passing through the endpoints of the DAC transfer function. It
is measured after adjusting for zero and full scale and is normally
expressed in LSBs or as a percentage of the full-scale reading.
The error due to capacitive feedthrough from the DAC
reference input to the DAC IOUT1 terminal when all 0s are
loaded to the DAC.
Digital Crosstalk
Differential Nonlinearity
The glitch impulse transferred to the outputs of a DAC in
response to a full-scale code change (all 0s to all 1s, or vice
versa) in the input register of another DAC. It is expressed in
nV-sec.
The difference in the measured change and the ideal 1 LSB
change between two adjacent codes. A specified differential
nonlinearity of −1 LSB maximum over the operating temper-
ature range ensures monotonicity.
Analog Crosstalk
Gain Error (Full-Scale Error)
A measure of the output error between an ideal DAC and the
actual device output. For this DAC, ideal maximum output is
The glitch impulse transferred to the output of one DAC due to a
change in the output of another DAC. It is measured by loading
one of the input registers with a full-scale code change (all 0s to
all 1s, or vice versa) while keeping LDAC high and then pulsing
LDAC low and monitoring the output of the DAC whose digital
code has not changed. The area of the glitch is expressed in nV-sec.
VREF − 1 LSB. The gain error of the DAC is adjustable to zero
with an external resistance.
Output Leakage Current
The current that flows into the DAC ladder switches when they
are turned off. For the IOUT1 terminal, it can be measured by
loading all 0s to the DAC and measuring the IOUT1 current.
Minimum current flows into the IOUT2 line when the DAC is
loaded with all 1s.
Channel-to-Channel Isolation
The portion of input signal from a DAC’s reference input that
appears at the output of the other DAC. It is expressed in decibels.
Total Harmonic Distortion (THD)
The DAC is driven by an ac reference. The ratio of the rms sum
of the harmonics of the DAC output to the fundamental value is
the THD. Usually only the lower-order harmonics are included,
such as the second to the fifth harmonics.
Output Capacitance
Capacitance from IOUT1 or IOUT2 to AGND.
Output Current Settling Time
The amount of time for the output to settle to a specified level
for a full-scale input change. For this device, it is specified with
a 100 Ω resistor to ground.
2
2
2
2
V2 + V3 + V4 + V5
THD = 20 log
V1
Intermodulation Distortion (IMD)
Digital-to-Analog Glitch Impulse
The DAC is driven by two combined sine wave references
of frequencies fa and fb. Distortion products are produced
at sum and difference frequencies of mfa nfb, where m, n = 0,
1, 2, 3 ... Intermodulation terms are those for which m or n is
not equal to 0. The second-order terms include (fa + fb) and
(fa − fb), and the third-order terms are (2fa + fb), (2fa − fb),
(f + 2fa + 2fb), and (fa − 2fb). IMD is defined as
The amount of charge injected from the digital inputs to the
analog output when the inputs change state. This is typically
specified as the area of the glitch in either pA-sec or nV-sec,
depending on whether the glitch is measured as a current or
voltage signal.
Digital Feedthrough
When the device is not selected, high frequency logic activity
on the device’s digital inputs is capacitively coupled through the
device and produces noise on the IOUT pins and, subsequently,
on the following circuitry. This noise is digital feedthrough.
rms sum of the sum and diff distortion products
IMD = 20 log
rms amplitude of the fundamental
Compliance Voltage Range
The maximum range of (output) terminal voltage for which the
device provides the specified characteristics.
Rev. B | Page 13 of 24
AD5405
GENERAL DESCRIPTION
When an output amplifier is connected in unipolar mode, the
output voltage is given by
DAC SECTION
The AD5405 is a 12-bit, dual-channel, current-output DAC
consisting of a standard inverting R-2R ladder configuration.
Figure 31 shows a simplified diagram for a single channel of the
AD5405. The feedback resistor RFBA has a value of 2R. The
value of R is typically 10 kΩ (with a minimum of 8 kΩ and a
maximum of 13 kΩ). If IOUT1A and IOUT2A are kept at the same
potential, a constant current flows into each ladder leg,
regardless of digital input code. Therefore, the input resistance
presented at VREFA is always constant.
VOUT = −VREF × D 2n
where:
D is the fractional representation, in the range of 0 to 4,095, of
the digital word loaded to the DAC.
n is the resolution of the DAC.
With a fixed 10 V reference, the circuit shown in Figure 32 gives
a unipolar 0 V to −10 V output voltage swing. When VIN is an ac
signal, the circuit performs 2-quadrant multiplication.
R
R
R
V
REFA
2R
S1
2R
S2
2R
S3
2R
2R
Table 5 shows the relationship between digital code and the
expected output voltage for unipolar operation.
S12
R
R
A
FB
I
I
OUT1A
OUT 2A
Table 5. Unipolar Code
Digital Input
Analog Output (V)
−VREF (4,095/4,096)
−VREF (2,048/4,096) = −VREF/2
−VREF (1/4,096)
DAC DATA LATCHES
AND DRIVERS
1111 1111 1111
1000 0000 0000
0000 0000 0001
0000 0000 0000
Figure 31. Simplified Ladder Configuration
Access is provided to the VREF, RFB, IOUT1, and IOUT2 terminals of
the DAC, making the device extremely versatile and allowing it
to be configured for several operating modes, such as unipolar
output, bipolar output, or single-supply mode.
−VREF (0/4,096) = 0
Bipolar Operation
In some applications, it may be necessary to generate full
4-quadrant multiplying operation or a bipolar output swing.
This can be easily accomplished by using another external
amplifier, as shown in Figure 33.
CIRCUIT OPERATION
Unipolar Mode
Using a single op amp, this DAC can easily be configured to
provide 2-quadrant multiplying operation or a unipolar output
voltage swing, as shown in Figure 32.
V
DD
R1A
R
2R
FB
R1
2R
R
A
FB
R2A
C1
V
IN
V
DD
R2
2R
I
I
1A
2A
OUT
R1A
AD5405
A1
R2_3A
R3A
R1
2R
R
OUT
12-Bit DAC A
R
FB
2R
V
= –V TO +V
IN IN
OUT
R
A
FB
R3
2R
C1
R2A
A1
I
1A
2A
OUT
R2
2R
AGND
AD5405
A1
V
A
GND
REF
I
12-Bit DAC A
R
OUT
R2_3A
AGND
V
= 0V TO –V
IN
OUT
AGND
R3
2R
NOTES
1. SIMILAR CONFIGURATION FOR DAC B.
R3A
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
AGND
AGND
V
A
REF
GND
Figure 33. Bipolar Operation (4-Quadrant Multiplication)
AGND
When in bipolar mode, the output voltage is given by
VOUT = (VREF ×D 2n −1 ) −VREF
where:
NOTES
1. SIMILAR CONFIGURATION FOR DAC B.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
Figure 32. Unipolar Operation
D is the fractional representation, in the range of 0 to 4,095, of
the digital word loaded to the DAC.
n is the number of bits.
When VIN is an ac signal, the circuit performs 4-quadrant
multiplication.
Rev. B | Page 14 of 24
AD5405
Table 6 shows the relationship between the digital code and the
expected output voltage for bipolar operation.
Note that VIN is limited to low voltages because the switches in the
DAC ladder no longer have the same source-drain drive voltage.
As a result, their on resistance differs and degrades the integral
linearity of the DAC. Also, VIN must not go negative by more
than 0.3 V, or an internal diode turns on, causing the device to
exceed the maximum ratings. In this type of application, the full
range of multiplying capability of the DAC is lost.
Table 6. Bipolar Code
Digital Input
Analog Output (V)
+VREF (4,095/4,096)
0
−VREF (4,095/4,096)
−VREF (4,096/4,096)
1111 1111 1111
1000 0000 0000
0000 0000 0001
0000 0000 0000
Positive Output Voltage
Stability
The output voltage polarity is opposite to the VREF polarity for
dc reference voltages. To achieve a positive voltage output, an
applied negative reference to the input of the DAC is preferred
over the output inversion through an inverting amplifier because
of the resistor’s tolerance errors. To generate a negative reference,
the reference can be level-shifted by an op amp such that the
VOUT and GND pins of the reference become the virtual ground
and −2.5 V, respectively, as shown in Figure 35.
In the I-to-V configuration, the IOUT of the DAC and the
inverting node of the op amp must be connected as close as
possible, and proper PCB layout techniques must be used.
Because every code change corresponds to a step function, gain
peaking may occur if the op amp has limited gain bandwidth
product (GBP) and there is excessive parasitic capacitance at the
inverting node. This parasitic capacitance introduces a pole into
the open-loop response, which can cause ringing or instability
in the closed-loop applications circuit.
V
= +5V
DD
ADR03
V
V
IN
OUT
GND
An optional compensation capacitor, C1, can be added in parallel
with RFBA for stability, as shown in Figure 32 and Figure 33. Too
small a value of C1 can produce ringing at the output, whereas
too large a value can adversely affect the settling time. C1 should
be found empirically, but 1 pF to 2 pF is generally adequate for
the compensation.
+
5V
C
1
R
A
V
DD
FB
I
1A
2A
–2.5V
OUT
OUT
V
A
12-BIT DAC
GND
REF
I
V
= 0V TO +2.5V
OUT
–5V
NOTES
1. SIMILAR CONFIGURATION FOR DAC B.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
SINGLE-SUPPLY APPLICATIONS
Voltage-Switching Mode of Operation
Figure 35. Positive Voltage Output with Minimum Components
Figure 34 shows the DAC operating in the voltage-switching
mode. The reference voltage, VIN, is applied to the IOUT1A pin,
IOUT2A is connected to AGND, and the output voltage is
available at the VREFA terminal. In this configuration, a positive
reference voltage results in a positive output voltage, making
single-supply operation possible. The output from the DAC is
voltage at a constant impedance (the DAC ladder resistance).
Therefore, an op amp is necessary to buffer the output voltage.
The reference input no longer sees a constant input impedance,
but one that varies with code. Therefore, the voltage input
should be driven from a low impedance source.
ADDING GAIN
In applications where the output voltage must be greater than
VIN, gain can be added with an additional external amplifier, or
it can be achieved in a single stage. Consider the effect of temper-
ature coefficients of the thin film resistors of the DAC. Simply
placing a resistor in series with the RFB resistor causes mismatches
in the temperature coefficients, resulting in larger gain temper-
ature coefficient errors. Instead, the circuit of Figure 36 shows
the recommended method for increasing the gain of the circuit.
R1, R2, and R3 should have similar temperature coefficients,
but they need not match the temperature coefficients of the DAC.
This approach is recommended in circuits where gains of greater
than 1 are required.
V
DD
R
R
1
2
R
A
V
FB
DD
V
I
I
1A
IN
OUT
OUT
V
OUT
V
A
REF
2A
GND
NOTES
1. SIMILAR CONFIGURATION FOR DAC B.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
Figure 34. Single-Supply Voltage-Switching Mode
Rev. B | Page 15 of 24
AD5405
V
DD
Because only a fraction, D, of the current into the VREF terminal
is routed to the IOUT1 terminal, the output voltage changes as
follows:
C1
V
R
A
DD
FB
R1
V
I
1A
2A
OUT
Output Error Voltage Due to DAC Leakage = (Leakage × R)/D
where R is the DAC resistance at the VREF terminal.
12-BIT
DAC
V
A
IN
V
OUT
REF
I
OUT
R3
R2
GND
GAIN = R2 + R3
R2
For a DAC leakage current of 10 nA, R = 10 kΩ, and a gain (that
is, 1/D) of 16, the error voltage is 1.6 mV.
R1 = R2R3
R2 + R3
NOTES
1. SIMILAR CONFIGURATION FOR DAC B.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
REFERENCE SELECTION
When selecting a reference for use with the AD54xx series of
current output DACs, pay attention to the reference’s output
voltage temperature coefficient specification. This parameter not
only affects the full-scale error, but also can affect the linearity
(INL and DNL) performance. The reference temperature coef-
ficient should be consistent with the system accuracy specifica-
tions. For example, an 8-bit system required to hold its overall
specification to within 1 LSB over the temperature range 0°C to
50°C dictates that the maximum system drift with temperature
should be less than 78 ppm/°C. A 12-bit system with the same
temperature range to overall specification within 2 LSBs requires
a maximum drift of 10 ppm/°C. Choosing a precision reference
with low output temperature coefficient minimizes this error
source.
Figure 36. Increasing Gain of Current Output DAC
DIVIDER OR PROGRAMMABLE GAIN ELEMENT
Current-steering DACs are very flexible and lend themselves to
many applications. If this type of DAC is connected as the
feedback element of an op amp and RFBA is used as the input
resistor, as shown in Figure 37, the output voltage is inversely
proportional to the digital input fraction, D.
For D = 1 − 2−n, the output voltage is
VOUT = −VIN D = −VIN
(
1− 2−n
)
V
DD
V
IN
Table 7 lists some references available from Analog Devices that
are suitable for use with this range of current output DACs.
R
A
V
FB
DD
I
1A
OUT
V
A
REF
I
2A
OUT
AMPLIFIER SELECTION
GND
The primary requirement for the current-steering mode is an
amplifier with low input bias currents and low input offset
voltage. Because of the code-dependent output resistance of the
DAC, the input offset voltage of an op amp is multiplied by the
variable gain of the circuit. A change in this noise gain between
two adjacent digital fractions produces a step change in the
output voltage due to the amplifier’s input offset voltage. This
output voltage change is superimposed on the desired change in
output between the two codes and gives rise to a differential
linearity error, which, if large enough, could cause the DAC to
be nonmonotonic.
V
OUT
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 37. Current-Steering DAC Used as a Divider or
Programmable Gain Element
As D is reduced, the output voltage increases. For small
values of the digital fraction D, it is important to ensure that
the amplifier does not saturate and that the required accuracy is
met. For example, an 8-bit DAC driven with the binary code 0x10
(0001 0000)—that is, 16 decimal—in the circuit of Figure 37
should cause the output voltage to be 16 times VIN. However, if
the DAC has a linearity specification of 0.5 LSB, D can have a
weight in the range of 15.5/256 to 16.5/256 so that the possible
output voltage is in the range of 15.5 VIN to 16.5 VIN—an error
of 3%, even though the DAC itself has a maximum error of 0.2%.
The input bias current of an op amp also generates an offset at
the voltage output as a result of the bias current flowing in the
feedback resistor, RFB. Most op amps have input bias currents low
enough to prevent significant errors in 12-bit applications.
Common-mode rejection of the op amp is important in
voltage-switching circuits, because it produces a code-
dependent error at the voltage output of the circuit. Most
op amps have adequate common-mode rejection for use at
12-bit resolution.
DAC leakage current is also a potential error source in divider
circuits. The leakage current must be counterbalanced by an
opposite current supplied from the op amp through the DAC.
Provided that the DAC switches are driven from true wideband,
low impedance sources (VIN and AGND), they settle quickly.
Rev. B | Page 16 of 24
AD5405
Consequently, the slew rate and settling time of a voltage-
switching DAC circuit is determined largely by the output op
amp. To obtain minimum settling time in this configuration,
minimize capacitance at the VREF node (the voltage output node
in this application) of the DAC. This is done by using low input
capacitance buffer amplifiers and careful board design.
Most single-supply circuits include ground as part of the analog
signal range, which in turn requires an amplifier that can
handle rail-to-rail signals. Analog Devices offers a wide range of
single-supply amplifiers, as listed in Table 8 and Table 9.
Table 7. Suitable ADI Precision References
Part No. Output Voltage (V)
Initial Tolerance (%)
Temp Drift (ppm/°C)
ISS (mA)
Output Noise (μV p-p) Package
ADR01
ADR01
ADR02
ADR02
ADR03
ADR03
ADR06
ADR06
ADR431
ADR435
ADR391
ADR395
10
10
5
0.05
0.05
0.06
0.06
0.10
0.10
0.10
0.10
0.04
0.04
0.16
0.10
3
9
3
9
3
9
3
9
3
3
9
9
1
1
1
1
1
1
1
1
0.8
0.8
0.12
0.12
20
20
10
10
6
SOIC-8
TSOT-23, SC70
SOIC-8
TSOT-23, SC70
SOIC-8
TSOT-23, SC70
SOIC-8
TSOT-23, SC70
SOIC-8
SOIC-8
TSOT-23
TSOT-23
5
2.5
2.5
3
3
2.5
5
6
10
10
3.5
8
5
8
2.5
5
Table 8. Suitable ADI Precision Op Amps
0.1 Hz to 10 Hz
Noise (μV p-p)
Part No.
OP97
OP1177
AD8551
AD8603
AD8628
Supply Voltage (V)
2 to 20
2.5 to 15
2.7 to 5
1.8 to 6
2.7 to 6
VOS (Max) (μV)
IB (Max) (nA)
Supply Current (μA)
Package
25
60
5
50
5
0.1
2
0.05
0.001
0.1
0.5
0.4
1
2.3
0.5
600
500
975
50
SOIC-8
MSOP, SOIC-8
MSOP, SOIC-8
TSOT
850
TSOT, SOIC-8
Table 9. Suitable ADI High Speed Op Amps
Part No.
AD8065
AD8021
AD8038
AD9631
Supply Voltage (V)
BW @ ACL (MHz)
Slew Rate (V/μs)
VOS (Max) (μV) IB (Max) (nA)
Package
5 to 24
2.5 to 12
3 to 12
145
490
350
320
180
120
425
1,300
1,500
1,000
3,000
10,000
6,000
10,500
750
SOIC-8, SOT-23, MSOP
SOIC-8, MSOP
SOIC-8, SC70-5
SOIC-8
3 to 6
7,000
Rev. B | Page 17 of 24
AD5405
8xC51-to-AD5405 Interface
PARALLEL INTERFACE
Figure 39 shows the interface between the AD5405 and the
8xC51 family of DSPs. To facilitate external data memory
access, the address latch enable (ALE) mode is enabled. The low
byte of the address is latched with this output pulse during
access to the external memory. AD0 to AD7 are the multiplexed
low order addresses and data bus; they require strong internal
pull-ups when emitting 1s. During access to external memory,
A8 to A15 are the high order address bytes. Because these ports
are open drained, they also require strong internal pull-ups
when emitting 1s.
Data is loaded into the AD5405 in a 12-bit parallel word format.
Control lines
and R/ allow data to be written to or read
CS
W
from the DAC register. A write event takes place when
and
CS
R/ are brought low, data available on the data lines fills the
W
shift register, and the rising edge of
latches the data and
CS
transfers the latched data-word to the DAC register. The DAC
latches are not transparent; therefore, a write sequence must
consist of a falling and rising edge on
to ensure that data is
CS
loaded into the DAC register and that its analog equivalent is
reflected on the DAC output. A read event takes place when
A8 TO A15
ADDRESS BUS
R/ is held high and
W
is brought low. Data is loaded from the
CS
DAC register, goes back into the input register, and is output
onto the data line, where it can be read back to the controller for
verification or diagnostic purposes. The input and DAC
registers of these devices are not transparent; therefore, a falling
AD54051
1
8051
ADDRESS
DECODER
CS
and rising edge of
is required to load each data-word.
CS
WR
R/W
MICROPROCESSOR INTERFACING
DB0 TO DB11
8-BIT
LATCH
ALE
ADSP-21xx-to-AD5405 Interface
Figure 38 shows the AD5405 interfaced to the ADSP-21xx
series of DSPs as a memory-mapped device. A single wait state
may be necessary to interface the AD5405 to the ADSP-21xx,
depending on the clock speed of the DSP. The wait state can be
programmed via the data memory wait state control register of
the ADSP-21xx (see the ADSP-21xx family’s user manual for
details).
AD0 TO AD7
DATA BUS
1
ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 39. 8xC51-to-AD5405 Interface
ADSP-BF5xx-to-AD5405 Interface
Figure 40 shows a typical interface between the AD5405 and the
ADSP-BF5xx family of DSPs. The asynchronous memory write
cycle of the processor drives the digital inputs of the DAC. The
ADDR TO
ADRR
0
ADDRESS BUS
13
x line is actually four memory select lines. Internal ADDR
AMS
AD54051
1
ADSP-21xx
lines are decoded into
3–0; these lines are then inserted as
AMS
ADDRESS
DECODER
DMS
WR
chip selects. The rest of the interface is a standard handshaking
operation.
CS
R/W
ADDR TO
1
ADDRESS BUS
ADRR
19
DB0 TO DB11
AD54051
1
ADSP-BF5xx
DATA 0 TO
DATA 23
DATA BUS
ADDRESS
DECODER
AMSx
CS
1
ADDITIONAL PINS OMITTED FOR CLARITY.
AWE
R/W
Figure 38. ADSP21xx-to-AD5405 Interface
DB0 TO DB11
DATA 0 TO
DATA 23
DATA BUS
1
ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 40. ADSP-BF5xx-to-AD5405 Interface
Rev. B | Page 18 of 24
AD5405
possible with a double-sided board. In this technique, the
component side of the board is dedicated to the ground plane,
PCB LAYOUT AND POWER SUPPLY DECOUPLING
In any circuit where accuracy is important, careful consider-
ation of the power supply and ground return layout helps to
ensure the rated performance. The printed circuit board on
which the AD5405 is mounted should be designed so that the
analog and digital sections are separated and confined to
certain areas of the board. If the DAC is in a system where
multiple devices require an AGND-to-DGND connection, the
connection should be made at one point only. The star ground
point should be established as close as possible to the device.
and signal traces are placed on the soldered side.
It is good practice to use compact, minimum lead length PCB
layout design. Leads to the input should be as short as possible
to minimize IR drops and stray inductance.
The PCB metal traces between VREF and RFB should also be
matched to minimize gain error. To maximize high frequency
performance, the I-to-V amplifier should be located as close as
possible to the device.
These DACs should have ample supply bypassing of 10 μF in
parallel with 0.1 μF on the supply located as close as possible to
the package, ideally right up against the device. The 0.1 μF
capacitor should have low effective series resistance (ESR) and
low effective series inductance (ESI), like the common ceramic
types of capacitors that provide a low impedance path to ground
at high frequencies, to handle transient currents due to internal
logic switching. Low ESR 1 μF to 10 μF tantalum or electrolytic
capacitors should also be applied at the supplies to minimize
transient disturbance and filter out low frequency ripple.
EVALUATION BOARD FOR THE DACS
The evaluation board consists of a DAC and a current-to-
voltage amplifier, the AD8065. Included on the evaluation
board is a 10 V reference, the ADR01. An external reference
may also be applied via an SMB input.
The evaluation kit consists of a CD-ROM with self-installing
PC software to control the DAC. The software simply allows the
user to write a code to the device.
POWER SUPPLIES FOR THE EVALUATION BOARD
Components, such as clocks, that produce fast-switching signals
should be shielded with digital ground to avoid radiating noise
to other parts of the board, and they should never be run near
the reference inputs.
The board requires 12 V and +5 V supplies. The +12 V VDD
and −12 V VSS are used to power the output amplifier; the +5 V
is used to power the DAC (VDD1) and transceivers (VCC).
Both supplies are decoupled to their respective ground plane
with 10 ꢀF tantalum and 0.1 ꢀF ceramic capacitors.
Avoid crossover of digital and analog signals. Traces on
opposite sides of the board should run at right angles to each
other. This reduces the effects of feedthrough on the board. A
microstrip technique is by far the best, but its use is not always
Rev. B | Page 19 of 24
AD5405
Figure 41. Schematic of AD5405 Evaluation Board
Figure 42. Component-Side Artwork
Rev. B | Page 20 of 24
AD5405
Figure 43. Silkscreen—Component-Side View (Top Layer)
Figure 44. Solder-Side Artwork
Rev. B | Page 21 of 24
AD5405
OVERVIEW OF AD54xx DEVICES
Table 10.
Part No.
AD5424
AD5426
AD5428
AD5429
AD5450
AD5432
AD5433
AD5439
AD5440
AD5451
AD5443
AD5444
AD5415
AD5405
AD5445
AD5447
AD5449
AD5452
AD5446
AD5453
AD5553
AD5556
AD5555
AD5557
AD5543
AD5546
AD5545
AD5547
Resolution
No. DACs
INL (LSB)
Interface
Parallel
Serial
Parallel
Serial
Serial
Serial
Parallel
Serial
Parallel
Serial
Serial
Serial
Serial
Parallel
Parallel
Parallel
Serial
Serial
Serial
Serial
Serial
Parallel
Serial
Parallel
Serial
Parallel
Serial
Parallel
Package1
RU-16, CP-20
RM-10
RU-20
Features
8
1
1
2
2
1
1
1
2
2
1
1
1
2
2
2
2
2
1
1
1
1
1
2
2
1
1
2
2
0.25
0.25
0.25
0.25
0.25
0.5
0.5
0.5
0.5
0.25
1
10 MHz BW, 17 ns CS pulse width
10 MHz BW, 50 MHz serial
10 MHz BW, 17 ns CS pulse width
10 MHz BW, 50 MHz serial
10 MHz BW, 50 MHz serial
10 MHz BW, 50 MHz serial
10 MHz BW, 17 ns CS pulse width
10 MHz BW, 50 MHz serial
10 MHz BW, 17 ns CS pulse width
10 MHz BW, 50 MHz serial
10 MHz BW, 50 MHz serial
10 MHz BW, 50 MHz serial
8
8
8
8
RU-10
UJ-8
RM-10
RU-20, CP-20
RU-16
10
10
10
10
10
12
12
12
12
12
12
12
12
14
14
14
14
14
14
16
16
16
16
RU-24
UJ-8
RM-10
RM-8
0.5
1
1
RU-24
10 MHz BW, 50 MHz serial
CP-40-1
RU-20, CP-20
RU-24
10 MHz BW, 17 ns CS pulse width
10 MHz BW, 17 ns CS pulse width
10 MHz BW, 17 ns CS pulse width
10 MHz BW, 50 MHz serial
10 MHz BW, 50 MHz serial
10 MHz BW, 50 MHz serial
1
1
1
0.5
1
2
1
RU-16
UJ-8, RM-8
RM-8
UJ-8, RM-8
RM-8
RU-28
10 MHz BW, 50 MHz serial
4 MHz BW, 50 MHz serial clock
4 MHz BW, 20 ns WR pulse width
4 MHz BW, 50 MHz serial clock
4 MHz BW, 20 ns WR pulse width
4 MHz BW, 50 MHz serial clock
4 MHz BW, 20 ns WR pulse width
4 MHz BW, 50 MHz serial clock
4 MHz BW, 20 ns WR pulse width
1
1
1
RM-8
RU-38
2
2
RM-8
RU-28
2
2
RU-16
RU-38
1 RU = TSSOP, CP = LFCSP, RM = MSOP, UJ = TSOT.
Rev. B | Page 22 of 24
AD5405
OUTLINE DIMENSIONS
6.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
31
40
1
30
PIN 1
INDICATOR
0.50
BSC
TOP
VIEW
4.25
4.10 SQ
3.95
5.75
BSC SQ
EXPOSED
PAD
(BOT TOM VIEW)
0.50
0.40
0.30
21
10
20
11
0.25 MIN
4.50
REF
12° MAX
0.80 MAX
0.65 TYP
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.05 MAX
0.02 NOM
1.00
0.85
0.80
0.30
0.23
0.18
COPLANARITY
0.08
0.20 REF
SECTION OF THIS DATA SHEET.
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VJJD-2
Figure 45. 40-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
6 mm × 6 mm Body, Very Thin Quad
(CP-40-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Resolution
INL (LSB)
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
40-Lead LFCSP_VQ
40-Lead LFCSP_VQ
40-Lead LFCSP_VQ
40-Lead LFCSP_VQ
40-Lead LFCSP_VQ
40-Lead LFCSP_VQ
Evaluation Kit
Package Option
CP-40-1
CP-40-1
CP-40-1
CP-40-1
AD5405YCP
12
12
12
12
12
12
1
1
1
1
1
1
AD5405YCP–REEL
AD5405YCP–REEL7
AD5405YCPZ
AD5405YCPZ–REEL
AD5405YCPZ–REEL7
EVAL-AD5405EB
CP-40-1
CP-40-1
1 Z = RoHS Compliant Part.
Rev. B | Page 23 of 24
AD5405
NOTES
©
2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04463–0–12/09(B)
Rev. B | Page 24 of 24
相关型号:
AD5405YCPZ-REEL
Dual 12-Bit, High Bandwidth, Multiplying DAC with 4 Quadrant Resistors and Parallel Interface
ADI
AD5405YCPZ-REEL7
Dual 12-Bit, High Bandwidth, Multiplying DAC with 4 Quadrant Resistors and Parallel Interface
ADI
AD5410ACPZ-REEL7
SERIAL INPUT LOADING, 40 us SETTLING TIME, 12-BIT DAC, QCC40, 6 X 6 MM, ROHS COMPLIANT, MO-220VJJD-2, LFCSP-40
ROCHESTER
©2020 ICPDF网 联系我们和版权申明