AD5383 [ADI]
32-Channel, 3 V/5 V, Single-Supply, 12-Bit, Voltage Output DAC; 32通道, 3 V / 5 V单电源, 12位电压输出DAC型号: | AD5383 |
厂家: | ADI |
描述: | 32-Channel, 3 V/5 V, Single-Supply, 12-Bit, Voltage Output DAC |
文件: | 总40页 (文件大小:1622K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
32-Channel, 3 V/5 V, Single-Supply,
12-Bit, Voltage Output DAC
AD5383
FEATURES
INTEGRATED FUNCTIONS
Guaranteed monotonic
Channel monitor
INL error: 1 LSB max
Simultaneous output update via LDAC
Clear function to user programmable code
Amplifier boost mode to optimize slew rate
User programmable offset and gain adjust
Toggle mode enables square wave generation
Thermal monitor
On-chip 1.25 V/2.5 V, 10 ppm/°C reference
Temperature range: –40°C to +85°C
Rail-to-rail output amplifier
Power-down mode
Package type: 100-lead LQFP (14 mm × 14 mm)
User Interfaces:
APPLICATIONS
Variable optical attenuators (VOA)
Level setting (ATE)
Optical micro-electro-mechanical systems (MEMS)
Control systems
Parallel
Serial (SPI®/QSPI™/MICROWIRE™/DSP compatible,
featuring data readback)
I2C® compatible
Instrumentation
FUNCTIONAL BLOCK DIAGRAM
DVDD (×3)
DGND (×3)
AVDD (×4)
AGND (×4)
DAC GND (×4)
REFGND
REFOUT/REFIN SIGNAL GND (×4)
PD
SER/PAR
AD5383
1.25V/2.5V
REFERENCE
FIFO EN
CS/(SYNC/AD0)
WR/(DCEN/AD1)
SDO
12
12
12
12
12
12
12
12
12
12
DAC
REG 0
INPUT
REG 0
DAC 0
VOUT0
DB11/(DIN/SDA)
DB10/(SCLK/SCL)
DB9/(SPI/I2C)
DB8
12
12
m REG 0
c REG 0
FIFO
+
STATE
MACHINE
+
R
R
R
R
R
R
R
R
INTERFACE
CONTROL
LOGIC
12
12
12
12
INPUT
REG 1
DAC
DAC 1
DB0
CONTROL
LOGIC
REG 1
VOUT1
VOUT2
VOUT3
VOUT4
VOUT5
VOUT6
12
12
A4
A0
m REG 1
c REG 1
REG 0
REG 1
RESET
BUSY
CLR
12
INPUT
REG 6
DAC
DAC 6
REG 6
POWER-ON
RESET
12
12
m REG 6
c REG 6
12
INPUT
REG 7
DAC
V
0………V
31
OUT
OUT
DAC 7
REG 7
VOUT7
VOUT8
12
12
MON_IN1
MON_IN2
MON_IN3
MON_IN4
m REG 7
c REG 7
36-TO-1
MUX
VOUT31
×4
MON_OUT
LDAC
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
AD5383
TABLE OF CONTENTS
General Description......................................................................... 3
Asynchronous Clear Function.................................................. 25
and Functions...................................................... 25
Specifications..................................................................................... 4
AD5383-5 Specifications............................................................. 4
AD5383-3 Specifications............................................................. 6
AC Characteristics........................................................................ 7
Timing Characteristics..................................................................... 8
Serial Interface Timing ................................................................ 8
I2C Serial Interface Timing........................................................ 10
Parallel Interface Timing ........................................................... 11
Absolute Maximum Ratings.......................................................... 13
Pin Configuration and Function Descriptions........................... 14
Terminology .................................................................................... 17
Typical Performance Characteristics ........................................... 18
Functional Description .................................................................. 21
DAC Architecture—General..................................................... 21
Data Decoding............................................................................ 21
On-Chip Special Function Registers (SFR) ............................ 22
SFR Commands.......................................................................... 22
Hardware Functions....................................................................... 25
Reset Function ............................................................................ 25
BUSY
LDAC
FIFO Operation in Parallel Mode............................................ 25
Power-On Reset.......................................................................... 25
Power-Down ............................................................................... 25
AD5383 Interfaces.......................................................................... 26
DSP, SPI, MICROWIRE Compatible Serial Interfaces.......... 26
I2C Serial Interface ..................................................................... 28
Parallel Interface......................................................................... 30
Microprocessor Interfacing....................................................... 31
Application Information................................................................ 33
Power Supply Decoupling ......................................................... 33
Typical Configuration Circuit .................................................. 33
AD5383 Monitor Function ....................................................... 34
Toggle Mode Function............................................................... 34
Thermal Monitor Function....................................................... 34
Optical Attenuators.................................................................... 35
Utilizing the AD5383 FIFO....................................................... 36
Outline Dimensions....................................................................... 37
Ordering Guide .......................................................................... 37
REVISION HISTORY
5/04—Revision 0: Initial Version
Rev. 0 | Page 2 of 40
AD5383
GENERAL DESCRIPTION
30 MHz, and an I2C compatible interface that supports a
400 kHz data transfer rate.
The AD5383 is a complete, single-supply, 32-channel, 12-bit
DAC available in a 100-lead LQFP package. All 32 channels
have an on-chip output amplifier with rail-to-rail operation.
The AD5383 includes a programmable internal 1.25 V/2.5 V,
10 ppm/°C reference, an on-chip channel monitor function that
multiplexes the analog outputs to a common MON_OUT pin
for external monitoring, and an output amplifier boost mode
that allows optimization of the amplifier slew rate. The AD5383
contains a double-buffered parallel interface that features a
An input register followed by a DAC register provides double
buffering, allowing the DAC outputs to be updated indepen-
dently or simultaneously using the
input.
LDAC
Each channel has a programmable gain and offset adjust
register that allows the user to fully calibrate any DAC channel.
Power consumption is typically 0.25 mA/channel with boost
off.
20 ns
pulse width, an SPI/QSPI/MICROWIRE/DSP
WR
compatible serial interface with interface speeds in excess of
Table 1. Other High Channel Count, Low Voltage, Single Supply DAC Products in Portfolio
Model
Resolution AVDD Range
Output Channels Linearity Error (LSB)
Package Description
100-Lead LQFP
100-Lead LQFP
100-Lead CSPBGA
100-Lead CSPBGA
100-Lead LQFP
100-Lead LQFP
100-Lead LQFP
100-Lead LQFP
52-Lead LQFP
64-Lead LFCSP
52-Lead LQFP
64-Lead LFCSP
52-Lead LQFP
64-Lead LFCSP
52-Lead LQFP
64-Lead LFCSP
52-Lead LQFP
Package Option
ST-100
ST-100
BC-100
BC-100
ST-100
ST-100
ST-100
ST-100
ST-52
CP-64
ST-52
CP-64
ST-52
CP-64
ST-52
CP-64
ST-52
AD5380BST-5
AD5380BST-3
AD5384BBC-5 14 Bits
AD5384BBC-3 14 Bits
14 Bits
14 Bits
4.5 V to 5.5 V
2.7 V to 3.6 V
4.5 V to 5.5 V
2.7 V to 3.6 V
4.5 V to 5.5 V
2.7 V to 3.6 V
4.5 V to 5.5 V
2.7 V to 3.6 V
4.5 V to 5.5 V
4.5 V to 5.5 V
2.7 V to 3.6 V
2.7 V to 3.6 V
4.5 V to 5.5 V
4.5 V to 5.5 V
2.7 V to 3.6 V
2.7 V to 3.6 V
4.5 V to 5.5 V
4.5 V to 5.5 V
2.7 V to 3.6 V
2.7 V to 3.6 V
40
40
40
40
40
40
32
32
16
16
16
16
16
16
16
16
8
4
4
4
4
1
1
4
4
3
3
3
3
1
1
1
1
3
3
3
3
AD5381BST-5
AD5381BST-3
AD5382BST-5
AD5382BST-3
AD5390BST-5
AD5390BCP-5 14 Bits
AD5390BST-3 14 Bits
AD5390BCP-3 14 Bits
AD5391BST-5 12 Bits
AD5391BCP-5 12 Bits
AD5391BST-3 12 Bits
AD5391BCP-3 12 Bits
AD5392BST-5 14 Bits
AD5392BCP-5 14 Bits
AD5392BST-3 14 Bits
AD5392BCP-3 14 Bits
12 Bits
12 Bits
14 Bits
14 Bits
14 Bits
8
8
8
64-Lead LFCSP
52-Lead LQFP
64-Lead LFCSP
CP-64
ST-52
CP-64
Table 2. 40-Channel, Bipolar Voltage Output DAC
Model
Resolution Analog Supplies
Output Channels
Linearity Error (LSB)
Package
Package Option
AD5379ABC 14 Bits
11.4 V to 16.5 V
40
3
108-Lead CSPBGA
BC-108
Rev. 0 | Page 3 of 40
AD5383
SPECIFICATIONS
AD5383-5 SPECIFICATIONS
Table 3. AVDD = 4.5 V to 5.5 V; DVDD = 2.7 V to 5.5 V, AGND = DGND = 0 V; External REFIN = 2.5 V;
all specifications TMIN to TMAX, unless otherwise noted
Parameter
AD5383-51
Unit
Test Conditions/Comments
ACCURACY
Resolution
12
Bits
Relative Accuracy2 (INL)
Differential Nonlinearity (DNL)
Zero-Scale Error
Offset Error
±1
±1
±4
±4
LSB max
LSB max
mV max
Guaranteed monotonic over temperature
Measured at Code 32 in the linear region
mV max
Offset Error TC
Gain Error
±±
µV/°C typ
% FSR max
% FSR max
ppm FSR/°C typ
LSB max
±0.024
±0.0ꢀ
2
At 2±°C
TMIN to TMAX
Gain Temperature Coefficient3
DC Crosstalk3
0.±
REFERENCE INPUT/OUTPUT
Reference Input3
Reference Input Voltage
DC Input Impedance
Input Current
Reference Range
Reference Output4
2.±
1
±10
1 to VDD/2
V
±1% for specified performance, AVDD = 2 × REFIN + ±0 mV
Typically 100 MΩ
Typically ±30 nA
MΩ min
µA max
V min/max
Enabled via CR8 in the AD±383 control register.
CR10 selects the reference voltage.
Output Voltage
2.49±/2.±0±
1.22/1.28
±10
V min/max
V min/max
ppm/°C typ
At ambient. Optimized for 2.± V operation. CR10 = 1
1.2± V reference selected. CR10 = 0
Reference TC
OUTPUT CHARACTERISTICS3
Output Voltage Range2
Short-Circuit Current
Load Current
0/AVDD
40
±1
V min/max
mA max
mA max
Capacitive Load Stability
RL = ∞
RL = ± kΩ
DC Output Impedance
MONITOR PIN
200
1000
0.±
pF max
pF max
Ω max
Output Impedance
Three-State Leakage Current
LOGIC INPUTS (EXCEPT SDA/SCL)3
VIH, Input High Voltage
VIL, Input Low Voltage
Input Current
±00
100
Ω typ
nA typ
DVDD = 2.7 V to ±.± V
2
V min
0.8
±10
10
V max
µA max
pF max
Total for all pins. TA = TMIN to TMAX
Pin Capacitance
LOGIC INPUTS (SDA, SCL ONLY)
VIH, Input High Voltage
VIL, Input Low Voltage
IIN, Input Leakage Current
VHYST, Input Hysteresis
CIN, Input Capacitance
Glitch Rejection
0.7 DVDD
0.3 DVDD
±1
0.0± DVDD
8
V min
SMBus compatible at DVDD < 3.ꢀ V
SMBus compatible at DVDD < 3.ꢀ V
V max
µA max
V min
pF typ
ns max
±0
Input filtering suppresses noise spikes of less than ±0 ns
Rev. 0 | Page 4 of 40
AD5383
Parameter
AD5383-51
Unit
Test Conditions/Comments
LOGIC OUTPUTS (BUSY, SDO)3
VOL, Output Low Voltage
VOH, Output High Voltage
VOL, Output Low Voltage
VOH, Output High Voltage
High Impedance Leakage Current
High Impedance Output Capacitance
LOGIC OUTPUT (SDA)3
0.4
DVDD – 1
0.4
DVDD – 0.±
±1
±
V max
V min
V max
V min
µA max
pF typ
DVDD = ± V ± 10%, sinking 200 µA
DVDD = ± V ± 10%, sourcing 200 µA
DVDD = 2.7 V to 3.ꢀ V, sinking 200 µA
DVDD = 2.7 V to 3.ꢀ V, sourcing 200 µA
SDO only
SDO only
VOL, Output Low Voltage
0.4
0.ꢀ
±1
8
V max
V max
µA max
pF typ
ISINK = 3 mA
ISINK = ꢀ mA
Three-State Leakage Current
Three-State Output Capacitance
POWER REQUIREMENTS
AVDD
4.±/±.±
2.7/±.±
V min/max
V min/max
DVDD
Power Supply Sensitivity3
∆Midscale/∆ΑVDD
AIDD
–8±
0.37±
0.47±
1
dB typ
mA/channel max
mA/channel max
mA max
Outputs unloaded, Boost off. 0.2± mA/channel typ
Outputs unloaded, Boost on. 0.32± mA/channel typ
VIH = DVDD, VIL = DGND.
DIDD
AIDD (Power-Down)
DIDD (Power-Down)
Power Dissipation
2
20
ꢀ±
µA max
µA max
mW max
Typically 200 nA
Typically 3 µA
Outputs unloaded, Boost off, AVDD = DVDD = ± V
1 AD±383-± is calibrated using an external 2.± V reference. Temperature range for all versions: –40°C to +8±°C.
2 Accuracy guaranteed from VOUT = 10 mV to AVDD – ±0 mV.
3 Guaranteed by characterization, not production tested.
4 Default on the AD±383-± is 2.± V. Programmable to 1.2± V via CR10 in the AD±383 control register; operating the AD±383-± with a 1.2± V reference will lead to
degraded accuracy specifications.
Rev. 0 | Page ± of 40
AD5383
AD5383-3 SPECIFICATIONS
Table 4. AVDD = 2.7 V to 3.6 V; DVDD = 2.7 V to 5.5 V, AGND = DGND = 0 V; external REFIN = 1.25 V;
all specifications TMIN to TMAX, unless otherwise noted
Parameter
AD5383-31
Unit
Test Conditions/Comments
ACCURACY
Resolution
12
Bits
Relative Accuracy2 (INL)
Differential Nonlinearity (DNL)
Zero-Scale Error
Offset Error
±1
±1
±4
±4
LSB max
LSB max
mV max
Guaranteed monotonic over temperature
Measured at Code 64 in the linear region
mV max
Offset Error TC
Gain Error
±±
µV/°C typ
% FSR max
% FSR max
ppm FSR/°C typ
LSB max
±0.024
±0.06
2
At 2±°C
TMIN to TMAX
Gain Temperature Coefficient3
DC Crosstalk3
0.±
REFERENCE INPUT/OUTPUT
Reference Input3
Reference Input Voltage
DC Input Impedance
Input Current
Reference Range
Reference Output4
1.2±
1
±10
1 to AVDD/2
V
±1% for specified performance
Typically 100 MΩ
Typically ±30 nA
MΩ min
µA max
V min/max
Enabled via CR8 in the AD±383 control register.
CR10 selects the reference voltage.
Output Voltage
1.247/1.2±3
2.43/2.±7
±10
V min/max
V min/max
ppm/°C typ
At ambient. Optimized for 1.2± V operation. CR10 = 0
2.± V reference enabled. CR10 = 1
Reference TC
OUTPUT CHARACTERISTICS3
Output Voltage Range2
Short-Circuit Current
Load Current
0/AVDD
40
±1
V min/max
mA max
mA max
Capacitive Load Stability
RL = ∞
RL = ± kΩ
DC Output Impedance
MONITOR PIN
200
1000
0.±
pF max
pF max
Ω max
Output Impedance
Three-State Leakage Current
LOGIC INPUTS (EXCEPT SDA/SCL)3
VIH, Input High Voltage
VIL, Input Low Voltage
Input Current
±00
100
Ω typ
nA typ
DVDD = 2.7 V to 3.6 V
2
V min
0.8
±10
10
V max
µA max
pF max
Total for all pins. TA = TMIN to TMAX
Pin Capacitance
LOGIC INPUTS (SDA, SCL ONLY)
VIH, Input High Voltage
VIL, Input Low Voltage
IIN, Input Leakage Current
VHYST, Input Hysteresis
CIN, Input Capacitance
Glitch Rejection
0.7 DVDD
0.3 DVDD
±1
0.0± DVDD
8
V min
SMBus compatible at DVDD < 3.6 V
SMBus compatible at DVDD < 3.6 V
V max
µA max
V min
pF typ
ns max
±0
Input filtering suppresses noise spikes of less than ±0 ns
Rev. 0 | Page 6 of 40
AD5383
Parameter
AD5383-31
Unit
Test Conditions/Comments
LOGIC OUTPUTS (BUSY, SDO)3
VOL, Output Low Voltage
VOH, Output High Voltage
High Impedance Leakage Current
High Impedance Output Capacitance
LOGIC OUTPUT (SDA)3
0.4
DVDD – 0.±
±1
±
V max
V min
µA max
pF typ
Sinking 200 µA
Sourcing 200 µA
SDO only
SDO only
VOL, Output Low Voltage
0.4
0.ꢀ
±1
8
V max
V max
µA max
pF typ
ISINK = 3 mA
ISINK = ꢀ mA
Three-State Leakage Current
Three-State Output Capacitance
POWER REQUIREMENTS
AVDD
2.7/3.ꢀ
2.7/±.±
V min/max
V min/max
DVDD
Power Supply Sensitivity3
∆Midscale/∆ΑVDD
AIDD
–8±
0.37±
0.47±
1
dB typ
mA/channel max
mA/channel max
mA max
Outputs unloaded, Boost off. 0.2± mA/channel typ
Outputs unloaded, Boost on. 0.32± mA/channel typ
VIH = DVDD, VIL = DGND.
DIDD
AIDD (Power-Down)
DIDD (Power-Down)
Power Dissipation
2
20
39
µA max
µA max
mW max
Typically 200 nA
Typically 3 µA
Outputs unloaded, Boost off, AVDD = DVDD = 3 V
1 AD±383-3 is calibrated using an external 1.2± V reference. Temperature range is –40°C to +8±°C.
2 Accuracy guaranteed from VOUT = 10 mV to AVDD – ±0 mV.
3 Guaranteed by characterization, not production tested.
4 Default on the AD±383-3 is 1.2± V. Programmable to 2.± V via CR10 in the AD±383 control register; operating the AD±383-3 with a 2.± V reference will lead to degraded
accuracy specifications and limited input code range.
AC CHARACTERISTICS1
Table 5. AVDD = 4.5 V to 5.5 V; DVDD = 2.7 V to 5.5 V; AGND = DGND= 0 V
Parameter
All
Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE
Output Voltage Settling Time2
1/4 scale to 3/4 scale change settling to ±1 LSB.
ꢀ
µs typ
8
2
3
µs max
Slew Rate2
V/µs typ
V/µs typ
nV-s typ
mV typ
Boost mode off, CR9 = 0
Boost mode on, CR9 = 1
Digital-to-Analog Glitch Energy
Glitch Impulse Peak Amplitude
Channel-to-Channel Isolation
DAC-to-DAC Crosstalk
Digital Crosstalk
Digital Feedthrough
12
1±
100
1
0.8
0.1
1±
40
dB typ
See Terminology section
See Terminology section
nV-s typ
nV-s typ
nV-s typ
µV p-p typ
µV p-p typ
Effect of input bus activity on DAC output under test
External reference, midscale loaded to DAC
Internal reference, midscale loaded to DAC
Output Noise 0.1 Hz to 10 Hz
Output Noise Spectral Density
@ 1 kHz
@ 10 kHz
1±0
100
nV/√Hz typ
nV/√Hz typ
1 Guaranteed by design and characterization, not production tested.
2 The slew rate can be programmed via the current boost control bit (CR9) in the AD±383 control register.
Rev. 0 | Page 7 of 40
AD5383
TIMING CHARACTERISTICS
SERIAL INTERFACE TIMING
Table 6. DVDD= 2.7 V to 5.5 V ; AVDD = 4.5 V to 5.5 V or 2.7 V to 3.6 V; AGND = DGND = 0 V; all specifications
TMIN to TMAX, unless otherwise noted
Parameter1, 2, 3
Limit at TMIN, TMAX
Unit
Description
t1
t2
t3
t4
33
13
13
13
13
33
10
±0
±
4.±
30
ꢀ70
20
20
100
0
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns max
ns max
ns min
ns min
ns max
ns min
ns min
µs typ
ns min
µs max
ns max
ns min
ns min
ns min
SCLK cycle time
SCLK high time
SCLK low time
SYNC falling edge to SCLK falling edge setup time
24th SCLK falling edge to SYNC falling edge
Minimum SYNC low time
4
t±
4
tꢀ
t7
Minimum SYNC high time
t7A
t8
t9
Minimum SYNC high time in Readback mode
Data setup time
Data hold time
24th SCLK falling edge to BUSY falling edge
BUSY pulse width low (single channel update)
24th SCLK falling edge to LDAC falling edge
LDAC pulse width low
4
t10
t11
4
t12
t13
t14
t1±
t1ꢀ
t17
t18
t19
BUSY rising edge to DAC output response time
BUSY rising edge to LDAC falling edge
LDAC falling edge to DAC output response time
DAC output settling time, Boost mode off
CLR pulse width low
100
8
20
3±
20
±
CLR pulse activation time
±
t20
t21
SCLK rising edge to SDO valid
SCLK falling edge to SYNC rising edge
SYNC rising edge to SCLK rising edge
SYNC rising edge to LDAC falling edge
±
±
t22
8
t23
20
1 Guaranteed by design and characterization, not production tested.
2 All input signals are specified with tr = tf = ± ns (10% to 90% of VCC) and are timed from a voltage level of 1.2 V.
3 See Figure 2, Figure 3, Figure 4, and Figure ±.
4 Standalone mode only.
± Daisy-chain mode only.
200µA
I
I
OL
V
V
(MIN) OR
(MAX)
OH
OL
TO OUTPUT PIN
C
L
50pF
200µA
OH
Figure 2. Load Circuit for SDO Timing Diagram
(Serial Interface, Daisy-Chain Mode)
Rev. 0 | Page 8 of 40
AD5383
t1
24
24
SCLK
t3
t6
t2
t5
t4
SYNC
DIN
t7
t8 t9
DB0
DB23
t10
t11
t13
BUSY
t12
t17
1
LDAC
t14
1
V
OUT
t15
t13
t17
2
2
LDAC
t16
V
OUT
t18
CLR
t19
V
OUT
1
2
LDAC ACTIVE DURING BUSY
LDAC ACTIVE AFTER BUSY
Figure 3. Serial Interface Timing Diagram (Standalone Mode)
SCLK
24
48
t7A
SYNC
DIN
DB23
DB0
DB23
DB23
DB0
INPUT WORD SPECIFIES
REGISTER TO BE READ
NOP CONDITION
DB0
SDO
UNDEFINED
SELECTED REGISTER
DATA CLOCKED OUT
Figure 4. Serial Interface Timing Diagram (Data Readback Mode)
t1
SCLK
24
48
t3
t2
t21
t7
t22
t4
SYNC
DIN
t8 t9
DB23
DB0 DB23
DB0
INPUT WORD FOR DAC N
INPUT WORD FOR DAC N+1
t20
DB23
DB0
SDO
UNDEFINED
INPUT WORD FOR DAC N
t13
t23
LDAC
Figure 5. Serial Interface Timing Diagram (Daisy-Chain Mode)
Rev. 0 | Page 9 of 40
AD5383
I2C SERIAL INTERFACE TIMING
Table 7. DVDD = 2.7 V to 5.5 V; AVDD = 4.5 V to 5.5 V or 2.7 V to 3.6 V; AGND = DGND = 0 V; all specifications
TMIN to TMAX, unless otherwise noted
Parameter1, 2
Limit at TMIN, TMAX
Unit
Description
FSCL
t1
t2
t3
t4
400
2.±
0.ꢀ
1.3
0.ꢀ
100
0.9
0
0.ꢀ
0.ꢀ
1.3
300
0
kHz max
µs min
µs min
µs min
µs min
ns min
µs max
µs min
µs min
µs min
µs min
ns max
ns min
ns max
ns min
ns max
ns min
pF max
SCL clock frequency
SCL cycle time
tHIGH, SCL high time
tLOW, SCL low time
tHD,STA, start/repeated start condition hold time
tSU,DAT, data setup time
tHD,DAT, data hold time
t±
tꢀ
3
tHD,DAT, data hold time
t7
t8
t9
t10
tSU,STA, setup time for repeated start
tSU,STO, stop condition setup time
tBUF, bus free time between a STOP and a START condition
tR, rise time of SCL and SDA when receiving
tR, rise time of SCL and SDA when receiving (CMOS compatible)
tF, fall time of SDA when transmitting
tF, fall time of SDA when receiving (CMOS compatible)
tF, fall time of SCL and SDA when receiving
tF, fall time of SCL and SDA when transmitting
Capacitive load for each bus line
t11
300
0
300
20 + 0.1Cb
400
4
Cb
1 Guaranteed by design and characterization, not production tested.
2 See Figure ꢀ.
3 A master device must provide a hold time of at least 300 ns for the SDA signal (referred to the VIH min of the SCL signal) in order to bridge the undefined region of SCL’s
falling edge.
4 Cb is the total capacitance, in pF, of one bus line. tR and tF are measured between 0.3DVDD and 0.7DVDD
.
SDA
t9
t3
t10
t11
t4
SCL
t4
t6
t2
t1
t8
t5
t7
START
CONDITION
REPEATED
START
STOP
CONDITION
CONDITION
Figure 6. I2C Compatible Serial Interface Timing Diagram
Rev. 0 | Page 10 of 40
AD5383
PARALLEL INTERFACE TIMING
Table 8. DVDD = 2.7 V to 5.5 V; AVDD = 4.5 V to 5.5 V or 2.7 V to 3.6 V; AGND = DGND = 0 V; all specifications
TMIN to TMAX, unless otherwise noted
Parameter1,2,3
Limit at TMIN, TMAX
Unit
Description
t0
t1
t2
t3
t4
t±
tꢀ
t7
t8
4.±
4.±
20
20
0
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns max
ns max
ns min
ns min
ns max
ns min
ns min
ns min
µs max
ns min
µs max
REG0, REG1, address to WR rising edge setup time
REG0, REG1, address to WR rising edge hold time
CS pulse width low
WR pulse width low
CS to WR falling edge setup time
WR to CS rising edge hold time
Data to WR rising edge setup time
Data to WR rising edge hold time
WR pulse width high
0
4.±
4.±
20
700
30
ꢀ70
30
20
100
20
0
4
t9
Minimum WR cycle time (single-channel write)
WR rising edge to BUSY falling edge
BUSY pulse width low (single-channel update)
WR rising edge to LDAC falling edge
LDAC pulse width low
4
t10
4, ±
t11
t12
t13
t14
t1±
t1ꢀ
t17
t18
t19
t20
BUSY rising edge to DAC output response time
LDAC rising edge to WR rising edge
BUSY rising edge to LDAC falling edge
LDAC falling edge to DAC output response time
DAC output settling time
100
8
20
3±
CLR pulse width low
CLR pulse activation time
1 Guaranteed by design and characterization, not production tested.
2 All input signals are specified with tR = tR = ± ns (10% to 90% of DVDD) and timed from a voltage level of 1.2 V.
3 See Figure 7.
4 See Figure 29.
± Measured with the load circuit of Figure 2.
Rev. 0 | Page 11 of 40
AD5383
t0
t1
REG0, REG1, A4..A0
t4
t5
t2
CS
t9
t3
t8
WR
t15
t6
t7
DB11..DB0
BUSY
t10
t11
t13
t12
t18
1
LDAC
t14
t16
1
V
OUT
2
LDAC
t13
t18
t17
2
V
OUT
CLR
t19
t20
V
OUT
1
2
LDAC ACTIVE DURING BUSY
LDAC ACTIVE AFTER BUSY
Figure 7. Parallel Interface Timing Diagram
Rev. 0 | Page 12 of 40
AD5383
ABSOLUTE MAXIMUM RATINGS
Table 9. TA = 25°C, unless otherwise noted1
Stresses above those listed under Absolute Maximum Ratings
Parameter
Rating
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
AVDD to AGND
–0.3 V to +7 V
DVDD to DGND
–0.3 V to +7 V
Digital Inputs to DGND
SDA/SCL to DGND
–0.3 V to DVDD + 0.3 V
–0.3 V to + 7 V
Digital Outputs to DGND
REFIN/REFOUT to AGND
AGND to DGND
–0.3 V to DVDD + 0.3 V
–0.3 V to AVDD + 0.3 V
–0.3 V to +0.3 V
VOUTx to AGND
–0.3 V to AVDD + 0.3 V
–0.3 V to AVDD + 0.3 V
–0.3 V to AVDD + 0.3 V
–0.3 V to AVDD + 0.3 V
Analog Inputs to AGND
MON_IN Inputs to AGND
MON_OUT to AGND
Operating Temperature Range
Commercial (B Version)
Storage Temperature Range
JunctionTemperature (TJ Max)
100-lead LQFP Package
θJAThermal Impedance
Reflow Soldering
–40°C to +85°C
–65°C to +150°C
150°C
44°C/W
230°C
Peak Temperature
1 Transient currents of up to 100 mA will not cause SCR latch-up
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
this product features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
Rev. 0 | Page 13 of 40
AD5383
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
FIFO EN
CLR
VOUT24
VOUT25
VOUT26
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
RESET
DB5
DB4
DB3
DB2
DB1
DB0
NC
NC
PIN 1
IDENTIFIER
2
3
4
5
6
VOUT27
SIGNAL_GND4
DAC_GND4
AGND4
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
AVDD4
VOUT28
VOUT29
VOUT30
REG0
REG1
VOUT23
VOUT22
VOUT21
VOUT20
AVDD3
AGND3
DAC_GND3
SIGNAL_GND3
VOUT19
VOUT18
VOUT17
VOUT16
AVDD2
AGND2
AD5383
TOP VIEW
(Not to Scale)
VOUT31
REF GND
REFOUT/REFIN
SIGNAL_GND1
DAC_GND1
AVDD1
VOUT0
VOUT1
VOUT2
VOUT3
VOUT4
AGND1
Figure 8. 100-Lead LQFP Pin Configuration
Table 10. Pin Function Descriptions
Mnemonic
Function
VOUTx
Buffered Analog Outputs for Channel x. Each analog output is driven by a rail-to-rail output amplifier operating at a
gain of 2. Each output is capable of driving an output load of 5 kΩ to ground. Typical output impedance is 0.5 Ω.
SIGNAL_GND(1–4)
DAC_GND(1–4)
AGND(1–4)
Analog Ground Reference Points for Each Group of Eight Output Channels. All SIGNAL_GND pins are tied together
internally and should be connected to the AGND plane as close as possible to the AD5383.
Each group of eight channels contains a DAC_GND pin. This is the ground reference point for the internal 12-bit DAC.
These pins shound be connected to the AGND plane.
Analog Ground Reference Point. Each group of eight channels contains an AGND pin. All AGND pins should be
connected externally to the AGND plane.
AVDD(1–4)
Analog Supply Pins. Each group of eight channels has a separate AVDD pin. These pins are connected together
internally and should be decoupled with a 0.1 µF ceramic capacitor and a 10 µF tantalum capacitor. Operating range
for the AD5383-5 is 4.5 V to 5.5 V; operating range for the AD5383-3 is 2.7 V to 3.6 V.
DGND
DVDD
Ground for All Digital Circuitry.
Logic Power Supply. Guaranteed operating range is 2.7 V to 5.5 V. It is recommended that these pins be decoupled
with 0.1 µF ceramic and 10 µF tantalum capacitors to DGND.
REFGND
Ground Reference Point for the Internal Reference.
REFOUT/REFIN
The AD5383 contains a common REFOUT/REFIN pin. When the internal reference is selected, this pin is the reference
output. If the application requires an external reference, it can be applied to this pin and the internal reference can
be disabled via the control register. The default for this pin is a reference input.
Rev. 0 | Page 14 of 40
AD5383
Mnemonic
Function
MON_OUT
When the monitor function is enabled, this output acts as the output of a 36-to-1 channel multiplexer that can be
programmed to multiplex one of Channels 0 to 31or any of the monitor input pins (MON_IN1 to MON_IN4) to the
MON_OUT pin. The MON_OUT pin’s output impedance is typically 500 Ω, and is intended to drive a high input
impedance like that exhibited by SAR ADC inputs.
MON_INx
MON_IN Monitor Input Pins. The AD5383 contains four monitor input pins that allow the user to connect input
signals within the maximum ratings of the device to these pins for monitoring purposes. Any of the signals applied
to the MON_IN pins along with the 32 output channels can be switched to the MON_OUT pin via software. An
external ADC for example can be used to monitor these signals.
SER/PAR
Interface Select Input. This pin allows the user to select whether the serial or parallel interface will be used. If it is tied
high, the serial interface mode is selected and Pin 97 (SPI/I2C) is used to determine if the interface mode is SPI or I2C.
Parallel interface mode is selected when SER/PAR is low.
CS/(SYNC/AD0)
In parallel interface mode, this pin acts as chip select input (level sensitive, active low). When low, the AD5383 is
selected.
Serial Interface Mode. This is the frame synchronization input signal for the serial clocks before the addressed
register is updated.
I2C Mode. This pin acts as a hardware address pin used in conjunction with AD1 to determine the software address
for the device on the I2C bus.
WR/(DCEN/ AD1)
Multifunction Pin. In parallel interface mode, this pin acts as write enable. In serial interface mode, this pin acts as a
daisy-chain enable in SPI mode and as a hardware address pin in I2C mode.
Parallel Interface Write Input (edge sensitive). The rising edge of WR is used in conjunction with CS low and the
address bus inputs to write to the selected device registers.
Serial Interface. Daisy-chain select input (level sensitive, active high). When high, this signal is used in conjunction
with SER/PAR high to enable the SPI serial interface Daisy-Chain mode.
I2C Mode. This pin acts as a hardware address pin used in conjunction with AD0 to determine the software address
for this device on the I2C bus.
DB11–DB0
A4–A0
Parallel Data Bus. DB11 is the MSB and DB0 is the LSB of the input data-word on the AD5383.
Parallel Address Inputs. A5 to A0 are decoded to address one of the AD5383’s 40 input channels. Used in conjunction
with the REG1 and REG0 pins to determine the destination register for the input data.
REG1, REG0
SDO/(A/B)
In parallel interface mode REG1 and REG0 are used in decoding the destination registers for the input data. REG1 and
REG0 are decoded to address the input data register, offset register, or gain register for the selected channel and are
also used to decide the special function registers.
Serial Data Output in Serial Interface Mode. Three-stateable CMOS output. SDO can be used for daisy-chaining a
number of devices together. Data is clocked out on SDO on the rising edge of SCLK, and is valid on the falling edge
of SCLK.
When operating in parallel interface mode, this pin acts as the A or B data register select when writing data to the
AD5383’s data registers with toggle mode selected (see the Toggle Mode Function section). In toggle mode, the
LDAC is used to switch the output between the data contained in the A and B data registers. All DAC channels
contain two data registers. In normal mode, Data Register A is the default for data transfers.
BUSY
LDAC
Digital CMOS Output. BUSY goes low during internal calculations of the data (x2) loaded to the DAC data register.
During this time, the user can continue writing new data to the x1, c, and m registers in parallel mode (these are
stored in a FIFO), but no further updates to the DAC registers and DAC outputs can take place. If LDAC is taken low
while BUSY is low, this event is stored. BUSY also goes low during power-on reset, and when the BUSY pin is low.
During this time, the interface is disabled and any events on LDAC are ignored. A CLR operation also brings BUSY
low.
Load DAC Logic Input (Active Low). If LDAC is taken low while BUSY is inactive (high), the contents of the input
registers are transferred to the DAC registers and the DAC outputs are updated. If LDAC is taken low while BUSY is
active and internal calculations are taking place, the LDAC event is stored and the DAC registers are updated when
BUSY goes inactive. However any events on LDAC during power-on reset or on RESET are ignored.
CLR
Asynchronous Clear Input. The CLR input is falling edge sensitive. When CLR is activated, all channels are updated
with the data contained in the CLR code register. BUSY is low for a duration of 35 µs while all channels are being
updated with the CLR code.
RESET
Asynchronous Digital Reset Input (Falling Edge Sensitive). The function of this pin is equivalent to that of the power-
on reset generator. When this pin is taken low, the state machine initiates a reset sequence to digitally reset the x1,
m, c, and x2 registers to their default power-on values. This sequence typically takes 270 µs. The falling edge of RESET
initiates the RESET process and BUSY goes low for the duration, returning high when RESET is complete. While BUSY
is low, all interfaces are disabled and all LDAC pulses are ignored. When BUSY returns high, the part resumes normal
operation and the status of the RESET pin is ignored until the next falling edge is detected.
Rev. 0 | Page 15 of 40
AD5383
Mnemonic
Function
PD
Power Down (Level Sensitive, Active High). PD is used to place the device in low power mode where the device
consumes 2 µA analog supply current and 20 µA digital supply current. In power-down mode, all internal analog
circuitry is placed in low power mode, and the analog output will be configured as a high impedance output or will
provide a 100 kΩ load to ground, depending on how the power-down mode is configured. The serial interface
remains active during power-down.
FIFOEN
FIFO Enable (Level Sensitive, Active High). When connected to DVDD, the internal FIFO is enabled, allowing the user
to write to the device at full speed. FIFO is only available in parallel interface mode. The status of the FIFO_EN pin is
sampled on power-up, and also following a CLEAR or RESET, to determine if the FIFO is enabled. In either serial or I2C
interface modes, the FIFO_EN pin should be tied low.
DB9 (SPI/I2C)
Multifunction Input Pin. In parallel interface mode, this pin acts as DB9 of the parallel input data-word. In serial
interface mode, this pin acts as serial interface mode select. When serial interface mode is selected (SER/PAR = 1) and
this input is low, SPI mode is selected. In SPI mode, DB12 is the serial clock (SCLK) input and DB11 is the serial data
(DIN) input.
When serial interface mode is selected (SER/PAR = 1) and this input is high I2C Mode is selected.
In this mode, DB12 is the serial clock (SCL) input and DB11 is the serial data (SDA) input.
DB10 (SCLK/SCL)
Multifunction Input Pin. In parallel interface mode, this pin acts as DB10 of the parallel input data-word. In serial
interface mode, this pin acts as a serial clock input.
Serial Interface Mode. In serial interface mode, data is clocked into the shift register on the falling edge of SCLK. This
operates at clock speeds up to 50 MHz.
I2C Mode. In I2C mode, this pin performs the SCL function, clocking data into the device. The data transfer rate in I2C
mode is compatible with both 100 kHz and 400 kHz operating modes.
DB11/(DIN/SDA)
NC
Multifunction Data Input Pin. In parallel interface mode, this pin acts as DB11 of the parallel input data-word.
Serial Interface Mode. In serial interface mode, this pin acts as the serial data input. Data must be valid on the falling
edge of SCLK.
I2C Mode. In I2C mode, this pin is the serial data pin (SDA) operating as an open-drain input/output.
No Connect. The user is advised not to connect any signal to these pins.
Rev. 0 | Page 16 of 40
AD5383
TERMINOLOGY
Relative Accuracy
DC Output Impedance
Relative accuracy or endpoint linearity is a measure of the
maximum deviation from a straight line passing through the
endpoints of the DAC transfer function. It is measured after
adjusting for zero-scale error and full-scale error, and is
expressed in LSB.
This is the effective output source resistance. It is dominated by
package lead resistance.
Output Voltage Settling Time
This is the amount of time it takes for the output of a DAC to
settle to a specified level for a ¼ to ¾ full-scale input change,
Differential Nonlinearity
and is measured from the
rising edge.
BUSY
Differential nonlinearity is the difference between the measured
change and the ideal 1 LSB change between any two adjacent
codes. A specified differential nonlinearity of 1 LSB maximum
ensures monotonicity.
Digital-to-Analog Glitch Energy
This is the amount of energy injected into the analog output at
the major code transition. It is specified as the area of the glitch
in nV-s. It is measured by toggling the DAC register data
between 0x1FFF and 0x2000.
Zero-Scale Error
Zero-scale error is the error in the DAC output voltage when all
0s are loaded into the DAC register. Ideally, with all 0s loaded to
the DAC and m = all 1s, c = 2n – 1
DAC-to-DAC Crosstalk
DAC-to-DAC crosstalk is the glitch impulse that appears at the
output of one DAC due to both the digital change and to the
subsequent analog output change at another DAC. The victim
channel is loaded with midscale. DAC-to-DAC crosstalk is
specified in nV-s.
VOUT(Zero-Scale) = 0 V
Zero-scale error is a measure of the difference between VOUT
(actual) and VOUT (ideal), expressed in mV. It is mainly due to
offsets in the output amplifier.
Digital Crosstalk
Offset Error
The glitch impulse transferred to the output of one converter
due to a change in the DAC register code of another converter
is defined as the digital crosstalk and is specified in nV-s.
Offset error is a measure of the difference between VOUT
(actual) and VOUT (ideal) in the linear region of the transfer
function, expressed in mV. Offset error is measured on the
AD5383-5 with Code 32 loaded into the DAC register, and on
the AD5383-3 with Code 64.
Digital Feedthrough
When the device is not selected, high frequency logic activity on
the device’s digital inputs can be capacitively coupled both
across and through the device to show up as noise on the
VOUT pins. It can also be coupled along the supply and ground
lines. This noise is digital feedthrough.
Gain Error
Gain Error is specified in the linear region of the output range
between VOUT = 10 mV and VOUT = AVDD – 50 mV. It is the
deviation in slope of the DAC transfer characteristic from the
ideal and is expressed in %FSR with the DAC output unloaded.
Output Noise Spectral Density
This is a measure of internally generated random noise.
Random noise is characterized as a spectral density (voltage per
√Hertz). It is measured by loading all DACs to midscale and
measuring noise at the output. It is measured in nV/√Hz in a
1 Hz bandwidth at 10 kHz.
DC Crosstalk
This is the dc change in the output level of one DAC at midscale
in response to a full-scale code (all 0s to all 1s, and vice versa)
and output change of all other DACs. It is expressed in LSB.
Rev. 0 | Page 17 of 40
AD5383
TYPICAL PERFORMANCE CHARACTERISTICS
1.00
1.00
0.75
0.50
0.25
0
AV = 5V
AV = 3V
DD
REFIN = 1.25V
DD
REFIN = 2.5V
0.75
0.50
0.25
0
T
= 25°C
T = 25°C
A
A
–0.25
–0.50
–0.75
–1.00
–0.25
–0.50
–0.75
–1.00
0
512
1024
1536
2048
2560
3072
3584
4096
0
512
1024
1536
2048
2560
3072
3584
4096
INPUT CODE
INPUT CODE
Figure 9. Typical AD5383-5 INL Plot
Figure 12. Typical AD5383-3 INL Plot
2.539
2.538
2.537
2.536
2.535
2.534
2.533
2.532
2.531
2.530
2.529
2.528
2.527
2.526
2.525
2.524
2.523
1.254
1.253
1.252
1.251
1.250
1.249
1.248
1.247
1.246
1.245
AV = DV = 5V
DD
DD
= 2.5V
AV = DV = 3V
DD DD
V
REF
V
= 1.25V
REF
T
= 25°C
A
T = 25°C
A
14ns/SAMPLE NUMBER
1 LSB CHANGE AROUND MIDSCALE
GLITCH IMPULSE = 10nV-s
14ns/SAMPLE NUMBER
1 LSB CHANGE AROUND MIDSCALE
GLITCH IMPULSE = 5nV-s
0
50 100 150 200 250 300 350 400 450 500 550
SAMPLE NUMBER
0
50 100 150 200 250 300 350 400 450 500 550
SAMPLE NUMBER
Figure 10. AD5383-5 Glitch Impulse
Figure 13. AD5383-3 Glitch Impulse
AV = DV = 5V
DD
DD
= 2.5V
V
REF
T
= 25°C
A
AV = DV = 5V
DD
DD
= 2.5V
V
T
REF
= 25°C
V
OUT
A
V
OUT
Figure 11. Slew Rate with Boost Off
Figure 14. Slew Rate with Boost On
Rev. 0 | Page 18 of 40
AD5383
14
12
10
8
AV = 5.5V
DD
V
= 2.5V
REF
= 25°C
T
A
AV = DV = 5V
DD
DD
= 2.5V
V
REF
T
= 25°C
A
POWER SUPPLY RAMP RATE = 10ms
V
OUT
6
4
AV
DD
2
8
9
10
AI (mA)
11
DD
Figure 15. AIDD Histogram
Figure 18. AD5383 Power-Up Transient
40
35
30
25
20
15
10
5
DV = 5.5V
DD
V
= DV
IH
IL
A
DD
10
8
V
T
= DGND
= 25°C
6
4
2
0
0
–5.0 –4.0 –3.0 –2.0 –1.0
0
1.0 2.0 3.0 4.0 5.0
0.4
0.5
0.6
DI (mA)
0.7
0.8
0.9
–4.5 –3.5 –2.5 –1.5 –0.5 0.5 1.5 2.5 3.5 4.5
DD
REFERENCE DRIFT (ppm/°C)
Figure 19. AD5383 REFOUT Temperature Coefficient
Figure 16. DIDD Histogram
PD
WR
BUSY
AV = DV = 5V
DD
DD
= 2.5V
V
REF
T
= 25°C
A
EXITS SOFT PD
TO MIDSCALE
V
OUT
AV = DV = 5V
DD DD
V
= 2.5V
= 25°C
REF
V
T
OUT
A
EXITS HARDWARE PD
TO MIDSCALE
Figure 17. Exiting Soft Power-Down
Figure 20. Exiting Hardware Power-Down
Rev. 0 | Page 19 of 40
AD5383
6
6
5
AV = DV = 3V
DD
DD
FULLSCALE
V
= 1.25V
REF
T
= 25°C
A
5
4
AV = DV = 5V
DD DD
V
= 2.5V
3/4 SCALE
REF
T
= 25°C
4
A
3/4 SCALE
FULL-SCALE
MIDSCALE
3
3
MIDSCALE
2
2
1/4 SCALE
1
1
ZEROSCALE
0
0
ZERO-SCALE
–5
1/4 SCALE
–1
–1
–40 –20 –10
–5
–2
0
2
5
10
20
40
–40 –20 –10
–2
0
2
5
10
20
–40
CURRENT (mA)
CURRENT (mA)
Figure 21. AD5383-5 Output Amplifier Source and Sink Capability
Figure 24. AD5383-3 Output Amplifier Source and Sink Capability
0.20
2.456
AV = 5V
DD
AV = DV = 5V
DD
DD
V
= 2.5V
V
T
= 2.5V
= 25°C
REF
REF
0.15
0.10
0.05
0
T
= 25°C
A
2.455
2.454
2.453
2.452
2.451
2.450
2.449
A
14ns/SAMPLE NUMBER
ERROR AT ZERO SINKING CURRENT
–0.05
–0.10
–0.15
–0.20
(V –V
) AT FULL-SCALE SOURCING CURRENT
DD OUT
0
0.25
0.50
0.75
1.00
/I
1.25
1.50
1.75
2.00
0
50 100 150 200 250 300 350 400 450 500 550
SAMPLE NUMBER
I
(mA)
SOURCE SINK
Figure 25. Adjacent Channel DAC-to-DAC Crosstalk
Figure 22. Headroom at Rails vs. Source/Sink Current
600
500
400
300
200
100
0
AV = DV = 5V
AV = 5V
DD
DD
DD
T = 25°C
T
= 25°C
A
A
DAC LOADED WITH MIDSCALE
EXTERNAL REFERENCE
Y AXIS = 5µV/DIV
REFOUT DECOUPLED
WITH 100nF CAPACITOR
X AXIS = 100ms/DIV
REFOUT = 2.5V
REFOUT = 1.25V
100
1k
10k
100k
Figure 26. 0.1 Hz to 10 Hz Noise Plot
FREQUENCY (Hz)
Figure 23. REFOUT Noise Spectral Density
Rev. 0 | Page 20 of 40
AD5383
FUNCTIONAL DESCRIPTION
The complete transfer function for these devices can be
represented as
DAC ARCHITECTURE—GENERAL
The AD5383 is a complete, single-supply, 32-channel voltage
output DAC that offers 12-bit resolution. The part is available in
a 100-lead LQFP package and features both a parallel and a
serial interface. This product includes an internal, software
selectable, 1.25 V/2.5 V, 10 ppm/°C reference that can be used to
drive the buffered reference inputs; alternatively, an external
reference can be used to drive these inputs. Internal/external
reference selection is via the CR8 bit in the control register;
CR10 selects the reference magnitude if the internal reference is
selected. All channels have an on-chip output amplifier with
rail-to-rail output capable of driving 5 kΩ in parallel with a
200 pF load.
V
OUT = 2 × VREF × x2/2n
x2 is the data-word loaded to the resistor string DAC. VREF is the
internal reference voltage or the reference voltage externally
applied to the DAC REFOUT/REFIN pin. For specified
performance, an external reference voltage of 2.5 V is
recommended for the AD5380-5 and 1.25 V for the AD5380-3.
DATA DECODING
The AD5383 contains a 12-bit data bus, DB11–DB0. Depending
on the value of REG1 and REG0 (see Table 11), this data is
loaded into the addressed DAC input registers, offset (c)
registers, or gain (m) registers. The format data, offset (c), and
gain (m) register contents are shown in Table 12 to Table 14.
V
AVDD
REF
×1 INPUT
REG
Table 11. Register Selection
DAC
REG
12-BIT
DAC
INPUT DATA m REG ×2
c REG
V
REG1
REG0
Register Selected
OUT
R
R
1
1
0
0
1
0
1
0
Input Data Register (x1)
Offset Register (c)
Gain Register (m)
Special Function Registers (SFRs)
Figure 27. Single-Channel Architecture
Table 12. DAC Data Format (REG1 = 1, REG0 = 1)
The architecture of a single DAC channel consists of a 12-bit
resistor-string DAC followed by an output buffer amplifier
operating at a gain of 2. This resistor-string architecture
guarantees DAC monotonicity. The 12-bit binary digital code
loaded to the DAC register determines at what node on the
string the voltage is tapped off before being fed to the output
amplifier. Each channel on these devices contains independent
offset and gain control registers that allow the user to digitally
trim offset and gain. These registers give the user the ability to
calibrate out errors in the complete signal chain, including the
DAC, using the internal m and c registers, which hold the
correction factors. All channels are double buffered, allowing
DB11 to DB0
DAC Output (V)
2 VREF × (4095/4096)
2 VREF × (4094/4096)
2 VREF × (2049/4096)
2 VREF × (2048/4096)
2 VREF × (2047/4096)
2 VREF × (1/4096)
0
1111
1111
1000
1000
0111
0000
0000
1111
1111
0000
0000
1111
0000
0000
1111
1110
0001
0000
1111
0001
0000
Table 13. Offset Data Format (REG1 = 1, REG0 = 0)
DB11 to DB0
Offset (LSB)
+2048
+2047
+1
0
–1
synchronous updating of all channels using the
pin.
LDAC
1111
1111
1000
1000
0111
0000
0000
1111
1111
0000
0000
1111
0000
0000
1111
1110
0001
0000
1111
0001
0000
Figure 27 shows a block diagram of a single channel on the
AD5383. The digital input transfer function for each DAC can
be represented as
x2 = [(m + 2)/ 2n × x1] + (c – 2n – 1
)
–2047
–2048
where:
x2 = the data-word loaded to the resistor string DAC.
x1 = the 12-bit data-word written to the DAC input register.
m = the gain coefficient (default is 0xFFE). The gain coefficient
is written to the 11 most significant bits (DB11 to DB1) and the
LSB (DB0) is 0.
Table 14. Gain Data Format (REG1 = 0, REG0 = 1)
DB11 to DB1
Gain Factor
1111
1011
0111
0011
0000
1111
1111
1111
1111
1110
1110
1110
1110
0000
1
0.75
0.5
0.25
0
n = DAC resolution (n = 12 for AD5383).
c is the12-bit offset coefficient (default is 0x800).
0000
Rev. 0 | Page 21 of 40
AD5383
ON-CHIP SPECIAL FUNCTION REGISTERS (SFR)
Soft CLR
The AD5383 contains a number of special function registers
(SFRs), as outlined in Table 15. SFRs are addressed with
REG1 = REG0 = 0 and are decoded using address bits A4 to A0.
REG1 = REG0 = 0, A4–A0 = 00010
DB11–DB0 = Don’t Care
Executing this instruction performs the CLR, which is function-
Table 15. SFR Register Functions (REG1 = 0, REG0 = 0)
ally the same as that provided by the external
pin. The
CLR
R/W
A4 A3 A2 A1 A0 Function
DAC outputs are loaded with the data in the CLR code register.
It takes 35 µs to fully execute the SOFT CLR, as indicated by the
X
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
1
1
0
1
0
0
1
0
0
0
0
1
1
0
1
0
0
1
0
0
0
1
NOP (No Operation)
Write CLR Code
Soft CLR
Soft Power-Down
Soft Power-Up
Control Register Write
Control Register Read
Monitor Channel
Soft Reset
low time.
BUSY
Soft Power-Down
REG1 = REG0 = 0, A4–A0 = 01000
DB11–DB0 = Don’t Care
Executing this instruction performs a global power-down
feature that puts all channels into a low power mode that
reduces the analog supply current to 2 µA max, and the digital
current to 20 µA. In power-down mode, the output amplifier
can be configured as a high impedance output or provide a 100
kΩ load to ground. The contents of all internal registers are
retained in power-down mode. No register can be written to
while in power-down.
SFR COMMANDS
NOP (No Operation)
REG1 = REG0 = 0, A4–A0 = 00000
Performs no operation but is useful in serial readback mode to
Soft Power-Up
clock out data on DOUT for diagnostic purposes.
pulses
BUSY
REG1 = REG0 = 0, A4–A0 = 01001
DB11–DB0 = Don’t Care
low during a NOP operation.
Write CLR Code
This instruction is used to power up the output amplifiers and
the internal reference. The time to exit power–down is 8 µs. The
hardware power-down and software function are internally
combined in a digital OR function.
REG1 = REG0 = 0, A4–A0 = 00001
DB11–DB0 = Contain the CLR data
Bringing the
line low or exercising the soft clear function
CLR
Soft RESET
will load the contents of the DAC registers with the data con-
tained in the user configurable CLR register, and will set
VOUT0 to VOUT31 accordingly. This can be very useful for
setting up a specific output voltage in a clear condition. It is also
beneficial for calibration purposes; the user can load full scale
or zero scale to the clear code register and then issue a hard-
ware or software clear to load this code to all DACs, removing
the need for individual writes to each DAC. Default on power-
up is all zeros.
REG1 = REG0 = 0, A4–A0 = 01111
DB11–DB0 = Don’t Care
This instruction is used to implement a software reset. All
internal registers are reset to their default values, which
correspond to m at full scale and c at zero. The contents of the
DAC registers are cleared, setting all analog outputs to 0 V. The
soft reset activation time is 135 µs.
Rev. 0 | Page 22 of 40
AD5383
Table 16. Control Register Contents
MSB
LSB
CR11
CR10
CR9
CR8
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
Control Register Write/Read
REG1 = REG0 = 0, A4–A0 = 01100, R/ status determines if
CR6: Thermal Monitor Function. This function is used to
monitor the AD5383’s internal die temperature when enabled.
The thermal monitor powers down the output amplifiers when
the temperature exceeds 130°C. This function can be used to
protect the device in cases where power dissipation may be
exceeded if a number of output channels are simultaneously
short-circuited. A soft power-up will re-enable the output
amplifiers if the die temperature has dropped below 130°C.
W
the operation is a write (R/ = 0) or a read (R/ = 1). DB11 to
W
W
DB0 contains the control register data.
Control Register Contents
CR11: Power-Down Status. This bit is used to configure the
output amplifier state in power down.
CR11 = 1. Amplifier output is high impedance (default on
power-up).
CR6 = 1: Thermal Monitor Enabled.
CR6 = 0: Thermal Monitor Disabled (default on power- up).
CR5 and CR4: Don’t Care.
CR11 = 0. Amplifier output is 100 kΩ to ground.
CR10: REF Select. This bit selects the operating internal
reference for the AD5383. CR12 is programmed as follows:
CR3 to CR0: Toggle Function Enable. This function allows the
user to toggle the output between two codes loaded to the A and
B register for each DAC. Control register bits CR3 to CR0 are
used to enable individual groups of eight channels for opera-
tion in toggle mode. A Logic 1 written to any bit enables a group
CR10 = 1: Internal reference is 2.5 V (AD5383-5 default), the
recommended operating reference for AD5383-5.
CR10 = 0: Internal reference is 1.25 V (AD5383-3 default),
the recommended operating reference for AD5383-3.
of channels; a Logic 0 disables a group.
is used to toggle
LDAC
between the two registers. Logic 1 enables a group of channels;
Logic 0 disables a group of channels.
CR9: Current Boost Control. This bit is used to boost the
current in the output amplifier, thereby altering its slew rate.
This bit is configured as follows:
Table 17.
CR Bit
Group
Channels
24–31
16–23
8–15
CR9 = 1: Boost Mode On. This maximizes the bias current in
the output amplifier, optimizing its slew rate but increasing
the power dissipation.
CR3
CR2
CR1
CR0
3
2
1
0
CR9 = 0: Boost Mode Off (default on power-up). This
reduces the bias current in the output amplifier and reduces
the overall power consumption.
0–7
Channel Monitor Function
REG1 = REG0 = 0, A4–A0 = 01010
CR8: Internal/External Reference. This bit determines if the
DAC uses its internal reference or an externally applied
reference.
DB11–DB6 = Contain data to address the monitored channel.
A channel monitor function is provided on the AD5383. This
feature, which consists of a multiplexer addressed via the
interface, allows any channel output or signals connected to the
MON_IN pins to be routed to the MON_OUT pin for
monitoring using an external ADC. The channel monitor
function must be enabled in the control register before any
channels are routed to MON_OUT. On the AD5383, DB11 to
DB6 contain the channel address for the monitored channel.
Selecting channel address 63 three-states MON_OUT.
CR8 = 1: Internal Reference Enabled. The reference output
depends on data loaded to CR10.
CR8 = 0: External Reference Selected (default on power up).
CR7: Channel Monitor Enable (see Channel Monitor Function)
CR7= 1: Monitor Enabled. This enables the channel monitor
function. After a write to the monitor channel in the SFR
register, the selected channel output is routed to the
MON_OUT pin.
CR7 = 0: Monitor Disabled (default on power-up). When the
monitor is disabled, the MON_OUT pin is tristated.
Rev. 0 | Page 23 of 40
AD5383
Table 18. AD5383 Channel Monitor Decoding
REG1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
•
REG0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
•
A4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
•
A3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
•
A2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
•
A1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
A0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
•
DB11
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
•
DB10
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
•
DB9
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
•
DB8
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
DB7
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
•
DB6
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
•
DB5–DB0
MON_OUT
VOUT0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
•
VOUT1
VOUT2
VOUT3
VOUT4
VOUT5
VOUT6
VOUT7
VOUT8
VOUT9
VOUT10
VOUT11
VOUT12
VOUT13
VOUT14
VOUT15
VOUT16
VOUT17
VOUT18
VOUT19
VOUT20
VOUT21
VOUT22
VOUT23
VOUT24
VOUT25
VOUT26
VOUT27
VOUT28
VOUT29
VOUT30
VOUT31
MON_IN1
MON_IN2
MON_IN3
MON_IN4
Undefined
Undefined
•
0
1
1
•
1
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
0
0
0
0
0
0
1
1
0
0
1
1
0
0
1
1
1
1
1
1
1
1
1
1
0
1
X
X
Undefined
Three-State
REG1 REG0 A4 A3 A2 A1 A0
0
0
0
1
0
1
0
VOUT0
VOUT1
AD5383
CHANNEL
MONITOR
DECODING
VOUT30
VOUT31
MON_IN1
MON_IN2
MON_IN3
MON_IN4
MON_OUT
CHANNEL ADDRESS
DB11–DB6
Figure 28. Channel Monitor Decoding
Rev. 0 | Page 24 of 40
AD5383
HARDWARE FUNCTIONS
RESET FUNCTION
FIFO OPERATION IN PARALLEL MODE
Bringing the
line low resets the contents of all internal
The AD5383 contains a FIFO to optimize operation when
operating in parallel interface mode. The FIFO Enable (level
sensitive, active high) is used to enable the internal FIFO. When
connected to DVDD, the internal FIFO is enabled, allowing the
user to write to the device at full speed. FIFO is only available in
parallel interface mode. The status of the FIFO_EN pin is
RESET
registers to their power-on reset state. Reset is a negative edge-
sensitive input. The default corresponds to m at full scale and to
c at zero. The contents of the DAC registers are cleared, setting
VOUT 0 to VOUT 31 to 0 V. This sequence takes 270 µs max.
The falling edge of
low for the duration, returning high when
initiates the reset process;
goes
RESET
BUSY
sampled on power-up, and after a
or , to determine
CLR RESET
is complete.
RESET
is low, all interfaces are disabled and all LDAC
if the FIFO is enabled. In either serial or I2C interface modes,
FIFO_EN should be tied low. Up to 128 successive instructions
can be written to the FIFO at maximum speed in parallel mode.
When the FIFO is full, any further writes to the device are
ignored. Figure 29 shows a comparison between FIFO mode
and non-FIFO mode in terms of channel update time. Figure 29
also outlines digital loading time.
While
BUSY
pulses are ignored. When
normal operation and the status of the
until the next falling edge is detected.
returns high, the part resumes
BUSY
pin is ignored
RESET
ASYNCHRONOUS CLEAR FUNCTION
Bringing the
line low clears the contents of the DAC
CLR
registers to the data contained in the user configurable CLR
register and sets VOUT 0 to VOUT 31 accordingly. This func-
tion can be used in system calibration to load zero scale and full
scale to all channels. The execution time for a CLR is 32 µs.
25
WITHOUT FIFO
20
(CHANNEL UPDATE TIME)
AND
FUNCTIONS
LDAC
BUSY
15
is a digital CMOS output that indicates the status of the
BUSY
AD5383. The value of x2, the internal data loaded to the DAC
data register, is calculated each time the user writes new data to
the corresponding x1, c, or m registers. During the calculation
10
WITH FIFO
(CHANNEL UPDATE TIME)
5
of x2, the
output goes low. While
is low, the user
BUSY
BUSY
WITH FIFO
(DIGITAL LOADING TIME)
can continue writing new data to the x1, m, or c registers, but no
DAC output updates can take place. The DAC outputs are
0
1
4
7
10 13 16 19 22 25 28 31 34 37 40
NUMBER OF WRITES
updated by taking the
input low. If
goes low while
LDAC
LDAC
is active, the
update immediately after
event is stored and the DAC outputs
BUSY
LDAC
BUSY
the LDAC input permanently low, in which case the DAC
outputs update immediately after goes high.
Figure 29. Channel Update Rate (FIFO vs. NON-FIFO)
goes high. The user may hold
POWER-ON RESET
also
BUSY
BUSY
goes low during power-on reset and when a falling edge is
detected on the pin. During this time, all interfaces are
The AD5383 contains a power-on reset generator and state
machine. The power-on reset resets all registers to a predefined
state and configures the analog outputs as high impedance. The
pin goes low during the power-on reset sequencing,
preventing data writes to the device.
RESET
disabled and any events on
are ignored. The AD5383
LDAC
BUSY
contains an extra feature whereby a DAC register is not updated
unless its x2 register has been written to since the last time
was brought low. Normally, when
is brought low,
LDAC
LDAC
POWER-DOWN
the DAC registers are filled with the contents of the x2 registers.
However, the AD5383 will only update the DAC register if the
x2 data has changed, thereby removing unnecessary digital
crosstalk.
The AD5383 contains a global power-down feature that puts all
channels into a low power mode and reduces the analog power
consumption to 2 µA max and digital power consumption to
20 µA max. In power-down mode, the output amplifier can be
configured as a high impedance output or provide a 100 kΩ
load to ground. The contents of all internal registers are
retained in power-down mode. When exiting power-down, the
settling time of the amplifier will elapse before the outputs settle
to their correct values.
Rev. 0 | Page 25 of 40
AD5383
AD5383 INTERFACES
The AD5383 contains both parallel and serial interfaces.
Furthermore, the serial interface can be programmed to be
either SPI, DSP, MICROWIRE, or I2C compatible. The SER/
Figure 3 and Figure 5 show timing diagrams for a serial write to
the AD5383 in standalone and daisy-chain modes. The 24-bit
data-word format for the serial interface is shown in Table 19
PAR
pin selects parallel and serial interface modes. In serial mode,
/B. When toggle mode is enabled, this pin selects whether the
data write is to the A or B register. With toggle disabled, this bit
should be set to zero to select the A data register.
A
the
/I2C pin is used to select DSP, SPI, MICROWIRE, or I2C
SPI
interface mode.
The devices use an internal FIFO memory to allow high speed
successive writes in parallel interface mode. The user can con-
tinue writing new data to the device while write instructions are
R/ is the read or write control bit.
W
A4–A0 are used to address the input channels.
being executed. The
signal indicates the current status of
BUSY
REG1 and REG0 select the register to which data is written, as
shown in Table 11.
the device, going low while instructions in the FIFO are being
executed. In parallel mode, up to 128 successive instructions can
be written to the FIFO at maximum speed. When the FIFO is
full, any further writes to the device are ignored.
DB11–DB0 contain the input data-word.
X is a don’t care condition.
To minimize both the power consumption of the device and the
on-chip digital noise, the active interface only powers up fully
when the device is being written to, i.e., on the falling edge of
Standalone Mode
By connecting the DCEN (Daisy-Chain Enable) pin low, stand-
alone mode is enabled. The serial interface works with both a
continuous and a noncontinuous serial clock. The first falling
or the falling edge of
.
WR
SYNC
DSP, SPI, MICROWIRE COMPATIBLE SERIAL
INTERFACES
edge of
starts the write cycle and resets a counter that
SYNC
counts the number of serial clocks to ensure that the correct
number of bits are shifted into the serial shift register. Any
The serial interface can be operated with a minimum of three
wires in standalone mode or four wires in daisy-chain mode.
Daisy chaining allows many devices to be cascaded together to
further edges on
except for a falling edge are ignored
SYNC
until 24 bits are clocked in. Once 24 bits have been shifted in,
the SCLK is ignored. In order for another serial transfer to take
place, the counter must be reset by the falling edge of
increase system channel count. The SER/
pin must be tied
PAR
high and the
/I2C pin (Pin 97) should be tied low to enable
SPI
.
SYNC
the DSP/SPI/MICROWIRE compatible serial interface. In serial
interface mode, the user does not need to drive the parallel
input data pins. The serial interface’s control pins are
, DIN, SCLK—Standard 3-Wire Interface Pins.
SYNC
DCEN—Selects Standalone Mode or Daisy-Chain Mode.
SDO—Data Out Pin for Daisy-Chain Mode.
Table 19. 40-Channel, 12-bit DAC Serial Input Register Configuration
MSB
LSB
X
A
/B
W
R/
0
A4
A3
A2
A1
A0
REG1
REG0
DB11
DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
X
Rev. 0 | Page 26 of 40
AD5383
Daisy-Chain Mode
Readback Mode
Readback mode is invoked by setting the R/ bit = 1 in the
serial input register write. With R/ = 1, Bits A4 to A0, in
W
For systems that contain several devices, the SDO pin may be
used to daisy-chain several devices together. This daisy-chain
mode can be useful in system diagnostics and in reducing the
number of serial interface lines.
W
association with Bits REG1 and REG0, select the register to be
read. The remaining data bits in the write sequence are don’t
cares. During the next SPI write, the data appearing on the SDO
output will contain the data from the previously addressed
register. For a read of a single register, the NOP command can
be used in clocking out the data from the selected register on
SDO. Figure 30 shows the readback sequence. For example, to
read back the M register of Channel 0 on the AD5383, the
following sequence should be implemented. First, write
0x404XXX to the AD5383 input register. This configures the
AD5383 for read mode with the m register of Channel 0
selected. Note that data bits DB11 to DB0 are don’t cares. Follow
this with a second write, a NOP condition, 0x000000. During
this write, the data from the m register is clocked out on the
DOUT line, i.e., data clocked out will contain the data from the
m register in Bits DB11 to DB0, and the top 10 bits contain the
address information as previously written. In readback mode,
By connecting the DCEN (Daisy-Chain Enable) pin high, daisy-
chain mode is enabled. The first falling edge of
starts the
SYNC
write cycle. The SCLK is continuously applied to the input shift
register when is low. If more than 24 clock pulses are
SYNC
applied, the data ripples out of the shift register and appears on
the SDO line. This data is clocked out on the rising edge of
SCLK and is valid on the falling edge. By connecting the SDO of
the first device to the DIN input on the next device in the chain,
a multidevice interface is constructed. Twenty-four clock pulses
are required for each device in the system. Therefore, the total
number of clock cycles must equal 24N, where N is the total
number of AD538x devices in the chain.
When the serial transfer to all devices is complete,
is
SYNC
taken high. This latches the input data in each device in the
daisy-chain and prevents any further data from being clocked
into the input shift register.
the
signal must frame the data. Data is clocked out on the
SYNC
rising edge of SCLK and is valid on the falling edge of the SCLK
signal. If the SCLK idles high between the write and read
operations of a readback operation, the first bit of data is
If the SYNC is taken high before 24 clocks are clocked into the
part, this is considered a bad frame and the data is discarded.
clocked out on the falling edge of
.
SYNC
The serial clock may be either a continuous or a gated clock. A
continuous SCLK source can only be used if it can be arranged
that
is held low for the correct number of clock cycles. In
SYNC
gated clock mode, a burst clock containing the exact number of
clock cycles must be used and
must be taken high after
SYNC
the final clock to latch the data.
SCLK
SYNC
24
48
DB23
DB0
DB23
DB0
DIN
INPUT WORD SPECIFIES REGISTER TO BE READ
NOP CONDITION
DB23
DB0
DB23
DB0
SDO
UNDEFINED
SELECTED REGISTER DATA CLOCKED OUT
Figure 30. Serial Readback Operation
Rev. 0 | Page 27 of 40
AD5383
I2C SERIAL INTERFACE
AD5383 Slave Addresses
The AD5383 features an I2C compatible 2-wire interface
consisting of a serial data line (SDA) and a serial clock line
(SCL). SDA and SCL facilitate communication between the
AD5383 and the master at rates up to 400 kHz. Figure 6 shows
the 2-wire interface timing diagrams that incorporate three
different modes of operation. In selecting the I2C operating
A bus master initiates communication with a slave device by
issuing a START condition followed by the 7-bit slave address.
When idle, the AD5383 waits for a START condition followed
by its slave address. The LSB of the address word is the Read/
Write (R/ ) bit. The AD5383 is a receive only device; when
W
mode, first configure serial operating mode (SER/
= 1) and
communicating with the AD5383, R/ = 0. After receiving the
W
proper address 10101 (AD1) (AD0) , the AD5383 issues an ACK
by pulling SDA low for one clock cycle.
PAR
then select I2C mode by configuring the
/I2C pin to a
SPI
Logic 1. The device is connected to the I2C bus as a slave device
(i.e., no clock is generated by the AD5383). The AD5383 has a
7-bit slave address 1010 1(AD1)(AD0). The 5 MSB are hard-
coded and the 2 LSB are determined by the state of the AD1 and
AD0 pins. The facility to hardware configure AD1 and AD0
allows four of these devices to be configured on the bus.
The AD5383 has four different user programmable addresses
determined by the AD1 and AD0 bits.
Write Operation
There are three specific modes in which data can be written to
the AD5383 DAC.
I2C Data Transfer
One data bit is transferred during each SCL clock cycle. The
data on SDA must remain stable during the high period of the
SCL clock pulse. Changes in SDA while SCL is high are control
signals that configure START and STOP conditions. Both SDA
and SCL are pulled high by the external pull-up resistors when
the I2C bus is not busy.
4-Byte Mode
When writing to the AD5383 DACs, the user must begin with
an address byte (R/ = 0) after which the DAC will acknowl-
W
edge that it is prepared to receive data by pulling SDA low. The
address byte is followed by the pointer byte; this addresses the
specific channel in the DAC to be addressed and is also
acknowledged by the DAC. Two bytes of data are then written
to the DAC, as shown in Figure 31. A STOP condition follows.
This allows the user to update a single channel within the
AD5383 at any time and requires four bytes of data to be
transferred from the master.
START and STOP Conditions
A master device initiates communication by issuing a START
condition. A START condition is a high-to-low transition on
SDA with SCL high. A STOP condition is a low-to-high
transition on SDA while SCL is high. A START condition from
the master signals the beginning of a transmission to the
AD5383. The STOP condition frees the bus. If a repeated
START condition (Sr) is generated instead of a STOP condition,
the bus remains active.
3-Byte Mode
In 3-byte mode, the user can update more than one channel in a
write sequence without having to write the device address byte
each time. The device address byte is only required once; sub-
sequent channel updates require the pointer byte and the data
bytes. In 3-byte mode, the user begins with an address byte
Repeated START Conditions
A repeated START (Sr) condition may indicate a change of data
direction on the bus. Sr may be used when the bus master is
writing to several I2C devices and wants to maintain control of
the bus.
(R/ = 0), after which the DAC will acknowledge that it is
W
prepared to receive data by pulling SDA low. The address byte is
followed by the pointer byte. This addresses the specific channel
in the DAC to be addressed and is also acknowledged by the
DAC. This is then followed by the two data bytes. REG1 and
REG0 determine the register to be updated.
Acknowledge Bit (ACK)
The acknowledge bit (ACK) is the ninth bit attached to any
8-bit data-word. ACK is always generated by the receiving
device. The AD5383 devices generate an ACK when receiving
an address or data by pulling SDA low during the ninth clock
period. Monitoring ACK allows for detection of unsuccessful
data transfers. An unsuccessful data transfer occurs if a
receiving device is busy or if a system fault has occurred. In the
event of an unsuccessful data transfer, the bus master should
reattempt communication.
If a STOP condition does not follow the data bytes, another
channel can be updated by sending a new pointer byte followed
by the data bytes. This mode only requires three bytes to be sent
to update any channel once the device has been initially
addressed, and reduces the software overhead in updating the
AD5383 channels. A STOP condition at any time exits this
mode. Figure 32 shows a typical configuration.
Rev. 0 | Page 28 of 40
AD5383
SCL
SDA
1
0
1
0
1
AD1
AD0
R/W
0
0
0
A4
A3
A2
A1
A0
START COND
BY MASTER
ACK BY
AD538x
MSB
ACK BY
AD538x
ADDRESS BYTE
POINTER BYTE
SCL
SDA
REG1 REG0
MSB
LSB
MSB
LSB
ACK BY
AD538x
ACK BY
AD538x
STOP
COND
BY
MOST SIGNIFICANT BYTE
LEAST SIGNIFICANT BYTE
MASTER
Figure 31. 4-Byte AD5383, I2C Write Operation
SCL
SDA
1
0
1
0
1
AD1
AD0
R/W
0
0
0
A4
A3
A2
A1
A0
START COND
BY MASTER
ACK BY
AD538x
MSB
ACK BY
AD538x
ADDRESS BYTE
POINTER BYTE FOR CHANNEL "N"
SCL
SDA
REG1 REG0
MSB
LSB
MSB
LSB
ACK BY
AD538x
ACK BY
AD538x
MOST SIGNIFICANT DATA BYTE
LEAST SIGNIFICANT DATA BYTE
DATA FOR CHANNEL "N"
SCL
SDA
0
0
0
A4
A3
A2
A1
A0
MSB
ACK BY
AD538x
POINTER BYTE FOR CHANNEL "NEXT CHANNEL"
SCL
SDA
REG1 REG0
MSB
LSB
MSB
LSB
ACK BY
AD538x
ACK BY STOP COND
AD538x BY MASTER
MOST SIGNIFICANT DATA BYTE
LEAST SIGNIFICANT DATA BYTE
DATA FOR CHANNEL "NEXT CHANNEL"
Figure 32. 3-Byte AD5383, I2C Write Operation
Rev. 0 | Page 29 of 40
AD5383
2-Byte Mode
PARALLEL INTERFACE
Following initialization of 2-byte mode, the user can update
channels sequentially. The device address byte is only required
once and the pointer address pointer is configured for auto-
increment or burst mode.
The SER/
pin must be tied low to enable the parallel
PAR
interface and disable the serial interfaces. Figure 7 shows the
timing diagram for a parallel write. The parallel interface is
controlled by the following pins:
The user must begin with an address byte (R/ = 0), after
W
Pin
CS
Active Low Device Select Pin.
Pin
which the DAC will acknowledge that it is prepared to receive
data by pulling SDA low. The address byte is followed by a
specific pointer byte (0xFF) that initiates the burst mode of
operation. The address pointer initializes to Channel 0, the data
following the pointer is loaded to channel 0, and the address
pointer automatically increments to the next address.
WR
On the rising edge of
A4 to A0 are latched; data present on the data bus is loaded into
the selected input registers.
, with
low, the addresses on Pins
CS
WR
REG0, REG1 Pins
The REG0 and REG1 bits in the data byte determine which
register will be updated. In this mode, following the initializa-
tion, only the two data bytes are required to update a channel.
The channel address automatically increments from Address 0
to Channel 31 and then returns to the normal 3-byte mode of
operation. This mode allows transmission of data to all
channels in one block and reduces the software overhead in
configuring all channels. A STOP condition at any time exits
this mode. Toggle mode is not supported in 2-byte mode.
Figure 33 shows a typical configuration.
The REG0 and REG1 pins determine the destination register of
the data being written to the AD5383. See Table 11.
Pins A4 to A0
Each of the 32 DAC channels can be addressed individually.
Pins DB11 to DB0
The AD5383 accepts a straight 12-bit parallel word on DB11 to
DB0, where DB11 is the MSB and DB0 is the LSB.
SCL
SDA
1
0
1
0
1
AD1
AD0
R/W
A7 = 1 A6 = 1 A5 = 1 A4 = 1 A3 = 1 A2 = 1 A1 = 1 A0 = 1
START COND
BY MASTER
ACK BY
CONVERTER
MSB
ACK BY
CONVERTER
ADDRESS BYTE
POINTER BYTE
SCL
SDA
REG1 REG0 MSB
LSB
MSB
LSB
ACK BY
AD538x
ACK BY
AD538x
MOST SIGNIFICANT DATA BYTE
LEAST SIGNIFICANT DATA BYTE
CHANNEL 0 DATA
SCL
SDA
REG1 REG0 MSB
LSB
MSB
LSB
ACK BY
ACK BY
CONVERTER
CONVERTER
MOST SIGNIFICANT DATA BYTE
LEAST SIGNIFICANT DATA BYTE
CHANNEL 1 DATA
SCL
SDA
REG1 REG0 MSB
LSB
MSB
LSB
ACK BY
ACK BY
STOP
CONVERTER
CONVERTER COND
MOST SIGNIFICANT DATA BYTE
LEAST SIGNIFICANT DATA BYTE
BY
MASTER
CHANNEL N DATA FOLLOWED BY STOP
Figure 33. 2-Byte, I2C Write Operation
Rev. 0 | Page 30 of 40
AD5383
MICROPROCESSOR INTERFACING
Parallel Interface
being transmitted to the AD5383, the SYNC line is taken low
The AD5383 can be interfaced to a variety of 16-bit microcon-
trollers or DSP processors. Figure 35 shows the AD5383 family
interfaced to a generic 16-bit microcontroller/DSP processor.
The lower address lines from the processor are connected to
A0–A4 on the AD5383. The upper address lines are decoded to
(PC7). Data appearing on the MOSI output is valid on the
falling edge of SCK. Serial data from the 68HC11 is transmitted
in 8-bit bytes with only eight falling clock edges occurring in
the transmit cycle.
provide a
,
signal for the AD5383. The fast interface
CS LDAC
DV
DD
MC68HC11
AD5383
timing of the AD5383 allows direct interface to a wide variety of
microcontrollers and DSPs, as shown in Figure 35.
SER/PAR
RESET
SDO
MISO
AD5383 to MC68HC11
MOSI
SCK
PC7
DIN
SCLK
SYNC
SPI/I2C
The serial peripheral interface (SPI) on the MC68HC11 is
configured for Master Mode (MSTR = 1), Clock Polarity bit
(CPOL) = 0, and the Clock Phase bit (CPHA) = 1. The SPI is
configured by writing to the SPI control register (SPCR)—see
the 68HC11 User Manual. SCK of the 68HC11 drives the SCLK
of the AD5383, the MOSI output drives the serial data line (DIN)
of the AD5383, and the MISO input is driven from DOUT. The
SYNC signal is derived from a port line (PC7). When data is
Figure 34. AD5383-to-MC68HC11 Interface
µCONTROLLER/
DSP PROCESSOR*
AD5383
D15
REG1
REG0
D11
DATA
BUS
D0
D0
CS
UPPER BITS OF
ADDRESS BUS
ADDRESS
DECODE
LDAC
A4
A3
A4
A3
A2
A1
A0
WR
A2
A1
A0
R/W
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 35. AD5383-to-Parallel Interface
Rev. 0 | Page 31 of 40
AD5383
DV
DD
AD5383 to PIC16C6x/7x
8XC51
AD5383
SER/PAR
The PIC16C6x/7x synchronous serial port (SSP) is configured
as an SPI master with the Clock Polarity bit = 0. This is done by
writing to the synchronous serial port control register
RESET
RxD
SDO
DIN
(SSPCON). See the PIC16/17 Microcontroller User Manual. In
TxD
P1.1
SCLK
SYNC
SPI/I2C
this example I/O, port RA1 is being used to pulse
and
SYNC
enable the serial port of the AD5383. This microcontroller
transfers only eight bits of data during each serial transfer
operation; therefore, three consecutive read/write operations
may be needed depending on the mode. Figure 36 shows the
connection diagram.
Figure 37. AD5383-to-8051 Interface
AD5383 to ADSP-2101/ADSP-2103
Figure 38 shows a serial interface between the AD5383 and the
ADSP-2101/ADSP-2103. The ADSP-2101/ADSP-2103 should
be set up to operate in SPORT transmit alternate framing mode.
The ADSP-2101/ADSP-2103 SPORT is programmed through
the SPORT control register and should be configured as follows:
internal clock operation, active low framing, and 16-bit word
length. Transmission is initiated by writing a word to the Tx
register after the SPORT has been enabled.
DV
DD
PIC16C6X/7X
AD5383
SER/PAR
RESET
SDO
SDI/RC4
SDO/RC5
SCK/RC3
RA1
DIN
SCLK
SYNC
SPI/I2C
Figure 36. AD5383-to-PIC16C6x/7x Interface
DV
DD
ADSP-2101/
ADSP-2103
AD5383
SER/PAR
AD5383 to 8051
RESET
SDO
The AD5383 requires a clock synchronized to the serial data.
The 8051 serial interface must therefore be operated in Mode 0.
In this mode, serial data enters and exits through RxD, and a
shift clock is output on TxD. Figure 37 shows how the 8051 is
connected to the AD5383. Because the AD5383 shifts data out
on the rising edge of the shift clock and latches data in on the
falling edge, the shift clock must be inverted. The AD5383
requires its data to be MSB first. Since the 8051 outputs the LSB
first, the transmit routine must take this into account.
DR
DT
SCK
TFS
RFS
DIN
SCLK
SYNC
SPI/I2C
Figure 38. AD5383-to-ADSP-2101/ADSP-2103 Interface
Rev. 0 | Page 32 of 40
AD5383
APPLICATION INFORMATION
an ADR421 or ADR431 2.5 V reference. Suitable external
POWER SUPPLY DECOUPLING
references for the AD5383-3 include the ADR280 1.2 V
reference. The reference should be decoupled at the
REFOUT/REFIN pin of the device with a 0.1 µF capacitor.
In any circuit where accuracy is important, careful considera-
tion of the power supply and ground return layout helps to
ensure the rated performance. The printed circuit board on
which the AD5383 is mounted should be designed so that the
analog and digital sections are separated and confined to
certain areas of the board. If the AD5383 is in a system where
multiple devices require an AGND-to-DGND connection, the
connection should be made at one point only, a star ground
point established as close to the device as possible.
AVDD
0.1µF
DVDD
10µF
0.1µF
ADR431/
ADR421
AVDD
DVDD
VOUT0
REFOUT/REFIN
For supplies with multiple pins (AVDD, DVDD), these pins should
be tied together. The AD5383 should have ample supply bypas-
sing of 10 µF in parallel with 0.1 µF on each supply, located as
close to the package as possible and ideally right up against the
device. The 10 µF capacitors are the tantalum bead type. The
0.1 µF capacitor should have low effective series resistance
(ESR) and effective series inductance (ESI), like the common
ceramic types that provide a low impedance path to ground at
high frequencies, to handle transient currents due to internal
logic switching.
0.1µF
AD5383-5
REFGND
VOUT31
DAC SIGNAL
GND GND AGND DGND
Figure 39. Typical Configuration with External Reference
Figure 40 shows a typical configuration when using the internal
reference. On power-up, the AD5383 defaults to an external
reference; therefore, the internal reference needs to be
configured and turned on via a write to the AD5383 control
register. Control Register Bit CR10 allows the user choose the
reference value; Bit CR 8 is used to select the internal reference.
It is recommended to use the 2.5 V reference when AVDD = 5 V,
and the 1.25 V reference when AVDD = 3 V.
The power supply lines of the AD5383 should use as large a
trace as possible to provide low impedance paths and reduce the
effects of glitches on the power supply line. Fast switching
signals such as clocks should be shielded with digital ground to
avoid radiating noise to other parts of the board, and should
never be run near the reference inputs. A ground line routed
between the DIN and SCLK lines will help reduce crosstalk
between them (this is not required on a multilayer board
because there will be a separate ground plane, but separating the
lines will help). It is essential to minimize noise on the VIN and
REFIN lines.
AVDD
0.1µF
DVDD
10µF
0.1µF
Avoid crossover of digital and analog signals. Traces on opposite
sides of the board should run at right angles to each other. This
reduces the effects of feedthrough through the board. A micro-
strip technique is by far the best, but is not always possible with
a double-sided board. In this technique, the component side of
the board is dedicated to the ground plane while signal traces
are placed on the solder side.
AVDD
DVDD
VOUT0
REFOUT/REFIN
0.1µF
AD5383
REFGND
VOUT31
DAC SIGNAL
GND GND AGND DGND
TYPICAL CONFIGURATION CIRCUIT
Figure 39 shows a typical configuration for the AD5383-5 when
configured for use with an external reference. In the circuit
shown, all AGND, SIGNAL_GND, and DAC_GND pins are tied
together to a common AGND. AGND and DGND are
connected together at the AD5383 device. On power-up, the
AD5383 defaults to external reference operation. All AVDD lines
are connected together and driven from the same 5 V source. It
is recommended to decouple close to the device with a 0.1 µF
ceramic and a 10 µF tantalum capacitor. In this application, the
reference for the AD5383-5 is provided externally from either
Figure 40. Typical Configuration with Internal Reference
Digital connections have been omitted for clarity. The AD5383
contains an internal power- on reset circuit with a 10 ms
brownout time. If the power supply ramp rate exceeds 10 ms,
the user should reset the AD5383 as part of the initialization
process to ensure the calibration data gets loaded correctly into
the device.
Rev. 0 | Page 33 of 40
AD5383
The
is used to switch between the A and B registers in
LDAC
AD5383 MONITOR FUNCTION
determining the analog output. The first
configures the
LDAC
The AD5383 contains a channel monitor function that consists
of a multiplexer addressed via the interface, allowing any chan-
nel output to be routed to this pin for monitoring using an
external ADC. The channel monitor function must be enabled
in the control register before any channels are routed to
MON_OUT. Table 18 contains the decoding information
needed to route any channel to MON_OUT. Selecting Channel
Address 63 three-states MON_OUT. Figure 41 shows a typical
monitoring circuit implemented using a 12-bit SAR ADC in a
6-lead SOT-23 package. The controller output port selects the
channel to be monitored, and the input port reads the converted
data from the ADC.
output to reflect data in the A registers. This mode offers signif-
icant advantages if the user wants to generate a square wave at
the output of all 32 channels, as might be required to drive a
liquid crystal based variable optical attenuator. In this case, the
user writes to the control register and enables the toggle func-
tion by setting CR3 to CR2 = 1, thus enabling the four groups of
eight for toggle mode operation. The user must then load data
to all 32 A and B registers. Toggling
sets the output
LDAC
values to reflect the data in the A and B registers. The
frequency determines the frequency of the square wave output.
’s
LDAC
Toggle mode is disabled via the control register. The first
following the disabling of the toggle mode updates the outputs
with the data contained in the A registers.
LDAC
TOGGLE MODE FUNCTION
The toggle mode function allows an output signal to be genera-
ted using the
control signal that switches between two
LDAC
THERMAL MONITOR FUNCTION
DAC data registers. This function is configured using the SFR
control register as follows. A write with REG1 = REG0 = 0 and
A4–A0 = 01100 specifies a control register write. The toggle
mode function is enabled in groups of eight channels using Bits
CR3 to CR0 in the control register. See the AD5383 control
register description. Figure 42 shows a block diagram of toggle
mode implementation. Each of the 32 DAC channels on the
AD5383 contain an A and B data register. Note that the B
registers can only be loaded when toggle mode is enabled. The
sequence of events when configuring the AD5383 for toggle
mode is
The AD5383 contains a temperature shutdown function to
protect the chip in case multiple outputs are shorted. The short
circuit current of each output amplifier is typically 40 mA.
Operating the AD5383 at 5 V leads to a power dissipation of
200 mW per shorted amplifier. With five channels shorted, this
leads to an extra watt of power dissipation. For the 100-lead
LQFP, the θJA is typically 44°C/W.
The thermal monitor is enabled by the user via CR6 in the
control register. The output amplifiers on the AD5383 are
automatically powered down if the die temperature exceeds
approximately 130°C. After a thermal shutdown has occurred,
the user can re-enable the part by executing a soft power-up if
the temperature has dropped below 130°C or by turning off the
thermal monitor function via the control register.
1. Enable toggle mode for the required channels via the
control register.
2. Load data to A registers.
3. Load data to B registers.
4. Apply
.
LDAC
AVCC
AVCC
REFOUT/REFIN
DIN
SYNC
SCLK
AD780/
ADR431
OUTPUT PORT
AVCC
MON_IN1
MON_IN2
AD7476
CS
MON_OUT
V
SCLK
INPUT PORT
IN
SDATA
VOUT0
AD5383
GND
CONTROLLER
AGND
VOUT31
DAC_GND SIGNAL_GND
Figure 41. Typical Channel Monitoring Circuit
Rev. 0 | Page 34 of 40
AD5383
DATA
REGISTER
A
DAC
REGISTER
V
12-BIT DAC
OUT
DATA
REGISTER
B
INPUT
DATA REGISTER
INPUT
LDAC
CONTROL INPUT
A/B
Figure 42. Toggle Mode Function
ADD
DROP
PORTS
PORTS
OPTICAL
SWITCH
PHOTODIODES
11
12
ATTENUATOR
ATTENUATOR
DWDM
IN
DWDM
OUT
FIBRE
AWG FIBRE
AWG
1n–1
1n
ATTENUATOR
ATTENUATOR
TIA/LOG AMP
(AD8304/AD8305)
ADG731
(32:1 MUX)
N:1 MULTIPLEXER
AD5383,
32-CHANNEL,
12-BIT DAC
AD7671
(0-5V, 1MSPS)
CONTROLLER
16-BIT ADC
Figure 43. OADM Using the AD5383 as Part of an Optical Attenuator
OPTICAL ATTENUATORS
Based on its high channel count, high resolution, monotonic
behavior, and high level of integration, the AD5383 is ideally
targeted at optical attenuation applications used in dynamic
gain equalizers, variable optical attenuators (VOA), and optical
add-drop multiplexers (OADM). In these applications, each
wavelength is individually extracted using an arrayed wave
guide; its power is monitored using a photodiode, transimped-
ance amplifier and ADC in a closed-loop control system. The
AD5383 controls the optical attenuator for each wavelength,
ensuring that the power is equalized in all wavelengths before
being multiplexed onto the fiber. This prevents information loss
and saturation from occurring at amplification stages further
along the fiber.
Rev. 0 | Page 35 of 40
AD5383
UTILIZING THE AD5383 FIFO
systems, as many as 320 channels need to be updated within
25 µs to 30 µs. Three-hundred-twenty channels require the use
of 10 AD5383s. With FIFO mode enabled, the data write cycle
time is 40 ns; therefore each group consisting of 32 channels can
be fully loaded in 1.28 µs. In FIFO mode, a complete group of
32 channels updates in 11.5 µs. The time taken to update all 320
channels is 11.5 µs + 9 × 1.28 µs = 23 µs. Figure 44 shows the
FIFO operation scheme.
The AD5383 FIFO mode optimizes total system update rates in
applications where a large number of channels need to be
updated. FIFO mode is only available when parallel interface
mode is selected. The FIFO_EN pin is used to enable the FIFO.
The status of FIFO_EN is sampled during the initialization
sequence. Therefore, the FIFO status can only be changed by
resetting the device. In a telescope that provides for the cancel-
lation of atmospheric distortion, for example, a large number of
channels need to be updated in a short period of time. In such
GROUP A
CHNLS 0-31
GROUP B
CHNLS 32-63
GROUP C
CHNLS
64-95
GROUP D
CHNLS
96-127
GROUP E
CHNLS
128-159
GROUP F
CHNLS
160-191
GROUP G
CHNLS
192-223
GROUP H
CHNLS
224-255
GROUP I
CHNLS
256-287
GROUP J
CHNLS
288-319
FIFO DATA LOAD
GROUP A
FIFO DATA LOAD
GROUP B
FIFO DATA LOAD
GROUP J
1.28µs
1.28µs
1.28µs
OUTPUT UPDATE
TIME FOR GROUP A
OUTPUT UPDATE
TIME FOR GROUP J
11.5µs
11.5µs
OUTPUT UPDATE
TIME FOR GROUP B
11.5µs
TIME TO UPDATE 320 CHANNELS = 23µs
Figure 44. Using FIFO Mode 320 Channels Updated in under 25 µs
Rev. 0 | Page 36 of 40
AD5383
OUTLINE DIMENSIONS
16.00 BSC SQ
14.00 BSC SQ
1.60 MAX
100
1
76
75
0.75
0.60
0.45
12°
TYP
PIN 1
SEATING
PLANE
12.00
REF
TOP VIEW
(PINS DOWN)
10°
6°
2°
1.45
1.40
1.35
0.20
0.09
VIEW A
7°
3.5°
0°
25
51
50
26
0.15
0.05
SEATING
PLANE
0.08 MAX
COPLANARITY
0.27
0.22
0.17
0.50 BSC
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026BED
Figure 45. 100-Lead Leaded Quad Flatpack [LQFP]
(ST-100)
Dimensions shown in millimeters
ORDERING GUIDE
Temperature
Range
AVDD
Range
Output
Channels
Linearity
Error
Package
Description
Package
Option
Model
Resolution
12 Bits
12 Bits
12 Bits
12 Bits
AD5383BST-3
AD5383BST-3-REEL
AD5383BST-5
AD5383BST-5-REEL
EVAL-AD5383EB
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
2.7 V to 3.6 V
2.7 V to 3.6 V
4.5 V to 5.5 V
4.5 V to 5.5 V
32
32
32
32
1 LSB
1 LSB
1 LSB
1 LSB
100-Lead LQFP
100-Lead LQFP
100-Lead LQFP
100-Lead LQFP
Evaluation Kit
ST-100
ST-100
ST-100
ST-100
Rev. 0 | Page 37 of 40
AD5383
NOTES
Rev. 0 | Page 38 of 40
AD5383
NOTES
Rev. 0 | Page 39 of 40
AD5383
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©
2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03734–0–5/04(0)
Rev. 0 | Page 40 of 40
相关型号:
AD5384BBC-3-REEL7
IC SERIAL INPUT LOADING, 8 us SETTLING TIME, 14-BIT DAC, PBGA100, 10 X 10 MM, MO-205AC, CSPBGA-100, Digital to Analog Converter
ADI
AD5384BBC-5-REEL7
IC SERIAL INPUT LOADING, 8 us SETTLING TIME, 14-BIT DAC, PBGA100, 10 X 10 MM, MO-205AC, CSPBGA-100, Digital to Analog Converter
ADI
©2020 ICPDF网 联系我们和版权申明