5962R0253801VXA [ADI]
Aerospace 12-Bit 41 MSPS ADC;
| 型号： | 5962R0253801VXA |
| 厂家： | 
ADI |
| 描述： | Aerospace 12-Bit 41 MSPS ADC CD 转换器 |
| 文件： | 总16页 (文件大小：154K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
B
C
D
Delete the Integral nonlinearity (INL) test as specified under table I. - ro
Add paragraph 3.11 and make changes to figure 2 block diagram. - ro
Made change to paragraph 2.1 and 3.11. - rrp
03-05-28
07-09-13
08-06-09
12-01-24
R. Monnin
R. Heber
R. Heber
Add device type 02. - drw
Charles F. Saffle
REV
SHEET
REV
D
SHEET
15
REV STATUS
OF SHEETS
PMIC N/A
REV
D
1
D
2
D
3
D
4
D
5
D
6
D
7
D
8
D
9
D
D
D
D
D
SHEET
10
11
12
13
14
PREPARED BY
Rick Officer
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Rajesh Pithadia
APPROVED BY
Raymond Monnin
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
MICROCIRCUIT, DIGITAL-LINEAR, 12-BIT,
41 MSPS ANALOG TO DIGITAL CONVERTER,
MONOLITHIC SILICON
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
02-08-01
REVISION LEVEL
D
SIZE
A
CAGE CODE
AMSC N/A
5962-02538
67268
SHEET
1 OF 15
DSCC FORM 2233
APR 97
5962-E086-12
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and
M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part
or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN.
1.2 PIN. The PIN is as shown in the following example:
5962
R
02538
01
V
X
A
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
/
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device types. The device types identify the circuit function as follows:
Device type
Generic number
Circuit function
01
02
AD9042S
AD9042S
12-bit, 41 MSPS analog to digital converter
12-bit, 41 MSPS analog to digital converter
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
follows:
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant, non-
JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A
Q or V
Certification and qualification to MIL-PRF-38535
1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 as follows:
Outline letter
Descriptive designator
Terminals
Package style
X
Z
CDIP2-T28
CDFP3-F28
28
28
Dual in line
Flat pack
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
2
DSCC FORM 2234
APR 97
1.3 Absolute maximum ratings. 1/
AV
DV
voltage ................................................................................................................ 7 V
voltage ................................................................................................................ 7 V
CC
CC
Analog input voltage ..................................................................................................... 0.5 V to 4.5 V
Analog input current ...................................................................................................... 20 mA
Digital input voltage (ENCODE) .................................................................................... 0 V to AV
CC
ENCODE, ENCODE differential voltage ...................................................................... 4 V
Digital output current ..................................................................................................... ±40 mA
Maximum junction temperature (T ) .............................................................................. +175°C
J
Lead temperature (soldering, 10 seconds) .................................................................... +300°C
Storage temperature range ........................................................................................... -65°C to +150°C
Thermal resistance, junction-to-case (θ
)
JC
Case X ....................................................................................................................... 14°C/W
Case Z ....................................................................................................................... 22°C/W
Thermal resistance, junction-to-ambient (θ ) :
JA
Case X ....................................................................................................................... 34°C/W
Case Z ....................................................................................................................... 60°C/W
1.4 Recommended operating conditions.
AV
DV
voltage ................................................................................................................ 5 V
voltage ................................................................................................................ 5 V
CC
CC
Ambient operating temperature range (T ) ................................................................... -55°C to +125°C
A
1.5 Radiation features.
Device type 01:
Maximum total dose available (dose rate = 50 – 300 rads(Si)/s) ............................... 100 krads (Si) 2/
Device type 02:
Maximum total dose available (dose rate ≤ 10 mrads(Si)/s) ...................................... 50 krads (Si) 3/
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883
-
Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
______
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability. T = +25°C.
A
2/ Device type 01 may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.
Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883,
method 1019, condition A.
3/ For device type 02, radiation end point limits for the noted parameters are guaranteed only for the conditions specified in
MIL-STD-883, method 1019, condition D.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
3
DSCC FORM 2234
APR 97
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 as specified herein, or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Block diagram. The block diagram shall be as specified on figure 2.
3.2.4 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document
revision level control and shall be made available to the preparing and acquiring activity upon request.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of
supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-
PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Conditions 1/, 2/, 3/
-55°C ≤ T ≤ +125°C
unless otherwise specified
Test
Symbol
Group A
subgroups
Device
type
Limits
Max
Unit
mA
A
Min
Static characteristics
I
CC
(total)
1, 2, 3
All
146
V
CC
supply
M,D,P,L,R
M,D,P,L
1
01
02
All
All
All
All
01
02
All
01
02
146
146
735
20
1
1, 2, 3
1
Power dissipation
4/
4/
mW
P
D
Power supply
rejection ratio
PSRR
-20
mV/V
T = 25°C
A
DC accuracy
Offset error
4/
No missing codes
OE
1, 2, 3
-10
-10
10
10
mV
M,D,P,L,R
1
M,D,P,L
1
-10
10
Gain error
GE
4, 5, 6
-6.5
-6.5
-6.5
6.5
6.5
6.5
%FS
M,D,P,L,R
M,D,P,L
4
4
ANALOG INPUT (AIN) section
V
V
REF
+0.5
REF
-0.5
Input voltage range
Input resistance
4/
IVR
1, 2, 3
4
All
All
V
4/, 5/
200
300
Ω
R
IN
T = 25°C
A
See footnotes at end of table.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – continued.
Conditions 1/, 2/, 3/
-55°C ≤ T ≤ +125°C
unless otherwise specified
Test
Symbol
Group A
subgroups
Device
type
Limits
Max
Unit
A
Min
ENCODE INPUT section (Logic compatibility, TTL / CMOS)
Logic “1” voltage
Logic “0” voltage
Logic “1” current
4/
4/
1, 2, 3
All
All
All
01
02
All
01
02
2
5
V
V
V
IH
1, 2, 3
0
0.8
V
IL
1, 2, 3
450
450
450
-400
-400
-400
800
800
800
-200
-200
-200
µA
I
V
V
= 5 V
IH
INH
M,D,P,L,R
M,D,P,L
1
1
Logic “0” current
1, 2, 3
µA
I
= 5 V
IL
INL
M,D,P,L,R
M,D,P,L
1
1
DIGITAL OUTPUTS section (Logic compatibility, CMOS)
Logic “1” voltage
Logic “0” voltage
4/
4/
1, 2, 3
1
All
All
3.5
V
V
V
V
I
I
= 10 µA
= 10 µA
OH
OH
OL
0.8
1
OL
2, 3
Dynamic characteristics section
Differential non-linearity
DNL
ENCODE = 20 MSPS
M,D,P,L,R
M,D,P,L
4, 5, 6
All
01
02
-2
-2
-2
2
2
2
LSB
4
4
See footnotes at end of table.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – continued.
Conditions 1/ 2/ 3/
-55°C ≤ T ≤ +125°C
unless otherwise specified
Test
Symbol
Group A
subgroups
Device
type
Limits
Max
Unit
A
Min
Switching characteristics section
Conversion rate
Output delay
4/ 5/
CR
9
9
All
All
5
5
41
14
MSPS
ns
T = 25°C
A
4/ 5/
4/ 5/
t
See figure 3, T = 25°C
A
OD
ENCODE pulse
width, high
EPW
EPWL
SNR
9
9
7
7
7
All
All
All
All
All
10
10
52
52
57
ns
ns
T = 25°C
A
ENCODE pulse
width, low
4/ 5/
T = 25°C
A
Analog input at –1 dBFS,
1.2, 9.6, and 19.6 MHz
Analog input at –1 dBFS,
1.2, 9.6, and 19.6 MHz
Analog input at –1 dBFS,
1.2, 9.6, and 19.6 MHz
Signal to noise ratio 4/ 6/
dB
dB
dBc
Signal to noise and 4/ 7/
distortion ratio
SINAD
WS
Worst spur ratio
4/ 8/
1/ Unless otherwise specified, AV
CC
= DV
CC
= +5 V, V
REF
tied to V through 50 Ω.
OFFSET
2/ Device type 01 supplied to this drawing has been characterized through all levels M, D, P, L, R of irradiation.
Device type 02 supplied to this drawing has been characterized through all levels P and L of irradiation.
However, device type 01 is only tested at the “R” level and device type 02 is only tested at the “L”. Pre and Post irradiation
values are identical unless otherwise specified in Table I. When performing post irradiation electrical measurements
for any RHA level, T = +25°C.
A
3/ Device type 01 may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.
Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883,
method 1019, condition A for device type 01. Device type 02 has been tested at low dose rate. For device type 02,
radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883, method
1019, condition D.
4/ Not tested post irradiation.
5/ Guaranteed by design, not tested.
6/ Analog input signal power at –1 dBFS; signal to noise ratio (SNR) is the ratio of the signal level to total noise
(first five harmonics removed).
7/ Analog input signal power at –1 dBFS; signal to noise and distortion (SINAD) is the ratio of signal level to
total noise + harmonics.
8/ Analog input signal power at –1 dBFS; worst spur is the ratio of the signal level to worst spur, usually limited by harmonics.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
7
DSCC FORM 2234
APR 97
Device type
01 and 02
X and Z
Case outlines
Terminal
number
Terminal symbol
GND
1
2
DV
CC
3
GND
4
ENCODE
5
ENCODE
GND
6
7
GND
AIN
8
9
V
OFFSET
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
V
REF
GND
AV
CC
GND
AV
CC
NC
NC
D0 (LSB)
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11 (MSB)
NC = No connection
FIGURE 1. Terminal connections.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
8
DSCC FORM 2234
APR 97
Symbol
GND
Description
Ground
+5 V Power supply (digital). Powers output stage only.
Encode input. Data conversion initiated on rising edge.
DV
CC
ENCODE
Complement of ENCODE. Drive differentially with ENCODE
or bypass to ground for single-ended clock mode.
ENCODE
AIN
Analog input.
Voltage offset input. Sets mid-point of analog input range.
V
OFFSET
Normally tied to V
REF
through 50Ω resistor.
Internal voltage reference. Nominally +2.4 V; normally tied
to V through 50Ω resistor. Bypass to GND with
V
REF
OFFSET
0.1 µF + 0.01 µF microwave chip capacitor.
+5 V power supply (analog).
AV
CC
NC
No connection.
D0 (LSB)
D1 – D10
Digital output bit. (Least Significant Bit)
Digital Output Bits.
Digital output bit. (Most Significant Bit)
D11
FIGURE 1. Terminal connections - continued.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
9
DSCC FORM 2234
APR 97
NOTE: Internal compensation capacitor C1 = 0.01 µF. See paragraph 3.11.
FIGURE 2. Block diagram.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
10
DSCC FORM 2234
APR 97
FIGURE 3. Timing waveforms.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
11
DSCC FORM 2234
APR 97
3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of
product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing.
3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime’s agent,
and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore
documentation shall be made available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 57 (see MIL-PRF-38535, appendix A).
3.11 Internal compensation capacitor C1. An external to the die discrete 0.01 µF capacitor is included inside the package.
Ceramic capacitors shall meet approved criteria (design, screening, and testing) in accordance with MIL-PRF-123 or as
approved by the qualifying activity. This bypass compensation capacitor is included to improve performance in the current
mirror section of the 2.4 V
circuitry. This capacitor is an integral part of the package design after date code 0731.
REF
4. VERIFICATION
4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with
MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan
shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in
accordance with MIL-PRF-38535, appendix A.
4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted
on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in
accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection.
4.2.1 Additional criteria for device class M.
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control
and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table IIA herein.
4.2.2 Additional criteria for device classes Q and V.
a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the
device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under
document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1015 of MIL-STD-883.
b. Interim and final electrical test parameters shall be as specified in table IIA herein.
c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in
MIL-PRF-38535, appendix B.
4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in
accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups
A, B, C, D, and E inspections (see 4.4.1 through 4.4.4).
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
12
DSCC FORM 2234
APR 97
4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with
MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified herein. Quality conformance inspection for
device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed
for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections
(see 4.4.1 through 4.4.4).
4.4.1 Group A inspection.
a. Tests shall be as specified in table IIA herein.
b. Subgroups 8, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted.
TABLE II. Electrical test requirements.
Subgroups
Subgroups
(in accordance with
(in accordance with
MIL-PRF-38535, table III)
Test requirements
MIL-STD-883,
method 5005, table I)
Device
Device
class Q
Device
class V
class M
Interim electrical
parameters (see 4.2)
Final electrical
1
1
1
1, 2, 3, 7 1/,
2/
1, 2, 3, 7 1/
1, 2, 3, 7 1/
parameters (see 4.2)
Group A test
1, 2, 3, 4, 5, 6, 1, 2, 3, 4, 5, 6,
1, 2, 3, 4, 5, 6, 7, 9
7, 9
7, 9
requirements (see 4.4)
Group C end-point electrical
parameters (see 4.4)
Group D end-point electrical
parameters (see 4.4)
Group E end-point electrical
parameters (see 4.4)
1
1
1
1
1
1
1
1
1
1/ PDA applies to subgroup 1. Deltas excluded from PDA.
2/ Delta limits as specified in table IIB shall be required where specified, and delta limits
shall be computed with reference to the previous endpoint electrical parameters.
TABLE IIB. 240 hour burn-in delta parameters.
Parameter
Device type
01, 02
Limit
Delta
Units
Min
3.5
Max
146
Min
Max
±20
mA
V
I
CC
±0.5
±0.2
V
OH
0.8
V
V
OL
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
13
DSCC FORM 2234
APR 97
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein.
4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883:
a. Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs,
outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-
STD-883.
b. TA = +125°C, minimum.
c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature,
or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The
test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-
STD-883.
4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table IIA herein.
4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured
(see 3.5 herein).
a. End-point electrical parameters shall be as specified in table IIA herein.
b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as
specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to
radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device
classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25°C ±5°C,
after exposure, to the subgroups specified in table IIA herein.
4.4.4.1 Total dose irradiation testing. Total dose irradiation testing shall be performed in accordance with MIL-STD-883
method 1019 condition A for device type 01, condition D for device type 02, and as specified herein.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes
Q and V or MIL-PRF-38535, appendix A for device class M.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
14
DSCC FORM 2234
APR 97
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor
prepared specification or drawing.
6.1.2 Substitutability. Device class Q devices will replace device class M devices.
6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.3 Record of users. Military and industrial users should inform DLA Land and Maritime when a system application requires
configuration control and which SMD's are applicable to that system. DLA Land and Maritime will maintain a record of users and
this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic
devices (FSC 5962) should contact DLA Land and Maritime -VA, telephone (614) 692-0544.
6.4 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-0540.
6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in
MIL-PRF-38535 and MIL-HDBK-1331.
6.6 Sources of supply.
6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535.
The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DLA Land and Maritime -VA and
have agreed to this drawing.
6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103.
The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been
submitted to and accepted by DLA Land and Maritime -VA.
SIZE
STANDARD
5962-02538
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
D
SHEET
COLUMBUS, OHIO 43218-3990
15
DSCC FORM 2234
APR 97
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 12-01-24
Approved sources of supply for SMD 5962-02538 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information
bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
Vendor
similar
PIN 2/
number
5962-0253801VXA
5962-0253801VZA
5962R0253801VXA
5962R0253801VZA
5962L0253802VZA
3/
AD9042SD/QMLV
AD9042SF/QMLV
AD9042SD/QMLR
AD9042SF/QMLR
AD9042SF/QMLL
3/
24355
24355
24355
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
3/ Not available from an approved source of supply.
Vendor CAGE
number
Vendor name
and address
24355
Analog Devices
Route 1 Industrial Park
P.O. Box 9106
Norwood, MA 02062
Point of contact: 7910 Triad Center Drive
Greensboro, NC 27409-9605
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
相关型号：
©2020 ICPDF网 联系我们和版权申明