S-1313B12H-M5T1U3 [ABLIC]
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR;型号: | S-1313B12H-M5T1U3 |
厂家: | ABLIC |
描述: | 105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR 输入元件 |
文件: | 总49页 (文件大小:889K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
S-1313xxxH Series
105°C OPERATION,
5.5 V INPUT, 200 mA VOLTAGE REGULATOR
www.ablic.com
© ABLIC Inc., 2018-2019
Rev.1.2_00
The S-1313xxxH Series, developed by using the CMOS technology, is a positive voltage regulator IC which has the super
low current consumption and the low dropout voltage.
Current consumption is as low as 0.9 μA typ., and a ceramic capacitor of 0.1 μF or more can be used as the input and output
capacitors.
It also has high-accuracy output voltage of 1.0%.
Features
• Output voltage:
• Input voltage:
1.0 V to 3.5 V, selectable in 0.05 V step.
1.5 V to 5.5 V
• Output voltage accuracy:
• Dropout voltage:
1.0% (1.0 V to 1.45 V output product: 15 mV)
170 mV typ. (2.8 V output product, IOUT = 100 mA)
• Current consumption:
During operation:
During power-off:
0.9 μA typ., 1.35 μA max.
0.01 μA typ., 0.1 μA max.
• Output current:
• Input capacitor:
• Output capacitor:
• Built-in overcurrent protection circuit:
• Built-in thermal shutdown circuit:
• Built-in ON / OFF circuit:
Possible to output 200 mA (VOUT(S) ≥ 1.4 V, VIN ≥ VOUT(S) + 1.0 V)*1
A ceramic capacitor can be used. (0.1 μF or more)
A ceramic capacitor can be used. (0.1 μF or more)
Limits overcurrent of output transistor
Detection temperature 150°C typ.
Ensures long battery life
Discharge shunt function "available" / "unavailable" is selectable.
Pull-down function "available" / "unavailable" is selectable.
Ta = −40°C to +105°C
• Operation temperature range:
• Lead-free (Sn 100%), halogen-free
*1. Please make sure that the loss of the IC will not exceed the power dissipation when the output current is large.
Applications
• Constant-voltage power supply for portable communication device, digital camera, and digital audio player
• Constant-voltage power supply for battery-powered device
• Constant-voltage power supply for home electric / electronic appliance
• Constant-voltage power supply for industrial equipment
Packages
• SOT-23-5
• SC-82AB
• HSNT-4(1010)
• HSNT-4(0808)
1
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Block Diagrams
1. S-1313xxxH Series A type
Function
Status
*1
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Active "H"
VIN
VOUT
Available
Available
Overcurrent
protection circuit
Thermal shutdown circuit
+
ON / OFF
ON / OFF circuit
−
Reference
voltage circuit
*1
VSS
*1. Parasitic diode
Figure 1
2. S-1313xxxH Series B type
Function
Status
*1
ON / OFF logic
Discharge shunt
function
Active "H"
VIN
VOUT
Available
Overcurrent
Constant current
source pull-down
protection circuit
Unavailable
Thermal shutdown circuit
+
ON / OFF
ON / OFF circuit
−
Reference
voltage circuit
*1
VSS
*1. Parasitic diode
Figure 2
2
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
3. S-1313xxxH Series C type
Function
Status
*1
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Active "H"
VIN
VOUT
Unavailable
Available
Overcurrent
protection circuit
Thermal shutdown circuit
+
ON / OFF
ON / OFF circuit
−
Reference
voltage circuit
VSS
*1. Parasitic diode
Figure 3
4. S-1313xxxH Series D type
Function
Status
*1
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Active "H"
VIN
VOUT
Unavailable
Unavailable
Overcurrent
protection circuit
Thermal shutdown circuit
+
ON / OFF
ON / OFF circuit
−
Reference
voltage circuit
VSS
*1. Parasitic diode
Figure 4
3
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Product Name Structure
Users can select the product type, output voltage, and package type for the S-1313xxxH Series. Refer to "1. Product
name" regarding the contents of product name, "2. Function list of product type" regarding the product type,
"3. Packages" regarding the package drawings, "4. Product name list" regarding details of the product name.
1. Product name
S-1313
x
xx
H
-
xxxx
U
3
Environmental code
U:
Lead-free (Sn 100%), halogen-free
Package abbreviation and IC packing specifications*1
M5T1: SOT-23-5, Tape
N4T1: SC-82AB, Tape
A4T2: HSNT-4(1010), Tape
A4T1: HSNT-4(0808), Tape
Operation temperature
H:
Ta = −40°C to +105°C
Output voltage*2
10 to 35
(e.g., when the output voltage is 1.0 V, it is expressed as 10.)
Product type*3
A to D
*1. Refer to the tape drawing.
*2. If you request the product which has 0.05 V step, contact our sales representatives.
*3. Refer to "2. Function list of product type".
2. Function list of product type
Table 1
Product Type
ON / OFF Logic
Active "H"
Discharge Shunt Function Constant Current Source Pull-down
A
B
C
D
Available
Available
Active "H"
Active "H"
Active "H"
Available
Unavailable
Available
Unavailable
Unavailable
Unavailable
3. Packages
Table 2 Package Drawing Codes
Package Name
SOT-23-5
Dimension
Tape
Reel
Land
MP005-A-P-SD
NP004-A-P-SD
PL004-A-P-SD
PK004-A-P-SD
MP005-A-C-SD
NP004-A-C-SD
PL004-A-C-SD
PK004-A-C-SD
MP005-A-R-SD
NP004-A-R-SD
PL004-A-R-SD
PK004-A-R-SD
−
−
SC-82AB
HSNT-4(1010)
HSNT-4(0808)
PL004-A-L-SD
PK004-A-L-SD
4
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
4. Product name list
4. 1 S-1313xxxH Series A type
ON / OFF logic:
Discharge shunt function:
Active "H"
Available
Constant current source pull-down: Available
Table 3
SOT-23-5
HSNT-4(1010)
HSNT-4(0808)
Output Voltage
1.2 V 15 mV
1.8 V 1.0%
2.3 V 1.0%
3.0 V 1.0%
3.3 V 1.0%
SC-82AB
S-1313A12H-M5T1U3
S-1313A18H-M5T1U3
S-1313A23H-M5T1U3
S-1313A30H-M5T1U3
S-1313A33H-M5T1U3
S-1313A12H-N4T1U3
S-1313A18H-N4T1U3
S-1313A23H-N4T1U3
S-1313A30H-N4T1U3
S-1313A33H-N4T1U3
S-1313A12H-A4T2U3
S-1313A18H-A4T2U3
S-1313A23H-A4T2U3
S-1313A30H-A4T2U3
S-1313A33H-A4T2U3
S-1313A12H-A4T1U3
S-1313A18H-A4T1U3
S-1313A23H-A4T1U3
S-1313A30H-A4T1U3
S-1313A33H-A4T1U3
Remark Please contact our sales representatives for products other than the above.
4. 2 S-1313xxxH Series B type
ON / OFF logic:
Discharge shunt function:
Active "H"
Available
Constant current source pull-down: Unavailable
Table 4
SC-82AB
1.2 V 15 mV S-1313B12H-M5T1U3 S-1313B12H-N4T1U3
SOT-23-5
HSNT-4(1010)
HSNT-4(0808)
Output Voltage
S-1313B12H-A4T2U3
S-1313B18H-A4T2U3
S-1313B23H-A4T2U3
S-1313B30H-A4T2U3
S-1313B33H-A4T2U3
S-1313B12H-A4T1U3
S-1313B18H-A4T1U3
S-1313B23H-A4T1U3
S-1313B30H-A4T1U3
S-1313B33H-A4T1U3
1.8 V 1.0%
2.3 V 1.0%
3.0 V 1.0%
3.3 V 1.0%
S-1313B18H-M5T1U3 S-1313B18H-N4T1U3
S-1313B23H-M5T1U3 S-1313B23H-N4T1U3
S-1313B30H-M5T1U3 S-1313B30H-N4T1U3
S-1313B33H-M5T1U3 S-1313B33H-N4T1U3
Remark Please contact our sales representatives for products other than the above.
4. 3 S-1313xxxH Series C type
ON / OFF logic:
Active "H"
Discharge shunt function:
Unavailable
Constant current source pull-down: Available
Table 5
SC-82AB
S-1313C12H-N4T1U3
S-1313C18H-N4T1U3
S-1313C23H-N4T1U3
S-1313C30H-N4T1U3
S-1313C33H-N4T1U3
SOT-23-5
HSNT-4(1010)
HSNT-4(0808)
Output Voltage
1.2 V 15 mV
1.8 V 1.0%
2.3 V 1.0%
3.0 V 1.0%
3.3 V 1.0%
S-1313C12H-M5T1U3
S-1313C18H-M5T1U3
S-1313C23H-M5T1U3
S-1313C30H-M5T1U3
S-1313C33H-M5T1U3
S-1313C12H-A4T2U3
S-1313C18H-A4T2U3
S-1313C23H-A4T2U3
S-1313C30H-A4T2U3
S-1313C33H-A4T2U3
S-1313C12H-A4T1U3
S-1313C18H-A4T1U3
S-1313C23H-A4T1U3
S-1313C30H-A4T1U3
S-1313C33H-A4T1U3
Remark Please contact our sales representatives for products other than the above.
4. 4 S-1313xxxH Series D type
ON / OFF logic:
Active "H"
Discharge shunt function:
Unavailable
Constant current source pull-down: Unavailable
Table 6
SC-82AB
Output Voltage
SOT-23-5
HSNT-4(1010)
HSNT-4(0808)
1.2 V 15 mV S-1313D12H-M5T1U3
S-1313D12H-N4T1U3
S-1313D18H-N4T1U3
S-1313D23H-N4T1U3
S-1313D30H-N4T1U3
S-1313D33H-N4T1U3
S-1313D12H-A4T2U3
S-1313D18H-A4T2U3
S-1313D23H-A4T2U3
S-1313D30H-A4T2U3
S-1313D33H-A4T2U3
S-1313D12H-A4T1U3
S-1313D18H-A4T1U3
S-1313D23H-A4T1U3
S-1313D30H-A4T1U3
S-1313D33H-A4T1U3
1.8 V 1.0%
2.3 V 1.0%
3.0 V 1.0%
3.3 V 1.0%
S-1313D18H-M5T1U3
S-1313D23H-M5T1U3
S-1313D30H-M5T1U3
S-1313D33H-M5T1U3
Remark Please contact our sales representatives for products other than the above.
5
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Pin Configurations
1. SOT-23-5
Top view
Table 7
Symbol
VIN
Pin No.
Description
Input voltage pin
5
4
1
2
3
4
5
VSS
GND pin
ON / OFF
NC*1
ON / OFF pin
No connection
Output voltage pin
1
2
3
VOUT
Figure 5
*1. The NC pin is electrically open.
The NC pin can be connected to the VIN pin or the VSS pin.
2. SC-82AB
Top view
Table 8
Pin No.
Symbol
ON / OFF
VSS
Description
4
3
1
2
3
4
ON / OFF pin
GND pin
VOUT
VIN
Output voltage pin
Input voltage pin
1
2
Figure 6
6
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
3. HSNT-4(1010)
Table 9
Pin No.
Symbol
VOUT
Description
Output voltage pin
Top view
1
2
3
4
1
2
4
3
VSS
GND pin
ON / OFF
VIN
ON / OFF pin
Input voltage pin
Bottom view
4
3
1
2
*1
Figure 7
*1. Connect the heatsink of backside at shadowed area to the board, and set electric potential GND.
However, do not use it as the function of electrode.
4. HSNT-4(0808)
Table 10
Symbol
VOUT
Pin No.
Description
Output voltage pin
Top view
1
2
3
4
1
2
4
3
VSS
GND pin
ON / OFF
VIN
ON / OFF pin
Input voltage pin
Bottom view
4
3
1
2
*1
Figure 8
*1. Connect the heat sink of backside at shadowed area to the board, and set electric potential GND.
However, do not use it as the function of electrode.
7
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Absolute Maximum Ratings
Table 11
(Ta = +25°C unless otherwise specified)
Item
Symbol
Absolute Maximum Rating
Unit
V
VIN
VSS − 0.3 to VSS + 6.0
VSS − 0.3 to VSS + 6.0
VSS − 0.3 to VIN + 0.3
240
Input voltage
VON / OFF
VOUT
IOUT
V
Output voltage
Output current
V
mA
°C
°C
Operation ambient temperature
Storage temperature
Topr
−40 to +105
−40 to +125
Tstg
Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.
Thermal Resistance Value
Table 12
Item
Symbol
Condition
Min.
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
Typ.
192
160
−
−
−
236
204
−
−
−
378
317
−
−
−
402
336
−
−
−
Max.
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
Unit
Board A
Board B
Board C
Board D
Board E
Board A
Board B
Board C
Board D
Board E
Board A
Board B
Board C
Board D
Board E
Board A
Board B
Board C
Board D
Board E
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
SOT-23-5
SC-82AB
Junction-to-ambient thermal resistance*1
θJA
HSNT-4(1010)
HSNT-4(0808)
−
−
−
−
−
−
−
−
*1. Test environment: compliance with JEDEC STANDARD JESD51-2A
Remark Refer to " Power Dissipation" and "Test Board" for details.
8
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Electrical Characteristics
Table 13
(Ta = +25°C unless otherwise specified)
Test
Circuit
Item
Symbol
Condition
Min.
Typ.
Max.
Unit
VOUT(S)
VOUT(S)
1.0 V
1.5 V
≤
≤
VOUT(S) < 1.5 V
VOUT(S) 3.5 V
VOUT(S)
VOUT(S)
V
1
−
0.015
+
0.015
V
IN = VOUT(S)
+
+
1.0 V,
1.0 V
Output voltage*1
Output current*2
VOUT(E)
IOUT = 30 mA
VOUT(S)
VOUT(S)
≤
V
1
×
0.99
×
1.01
1.0 V
1.1 V
1.2 V
1.3 V
1.4 V
1.0 V
1.1 V
1.2 V
1.3 V
1.4 V
1.5 V
1.7 V
1.8 V
2.0 V
2.5 V
2.8 V
3.0 V
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
VOUT(S) < 1.1 V
VOUT(S) < 1.2 V
VOUT(S) < 1.3 V
VOUT(S) < 1.4 V
100*5
−
−
−
−
−
−
−
−
−
1.55
1.39
1.25
1.11
0.99
0.85
0.68
0.58
0.49
0.38
0.33
0.32
mA
mA
mA
mA
mA
V
V
V
V
V
V
V
V
V
V
V
V
3
3
3
3
3
1
1
1
1
1
1
1
1
1
1
1
1
125*5
IOUT
VIN
≥
VOUT(S)
150*5
175*5
VOUT(S)
≤
3.5 V
200*5
−
VOUT(S) < 1.1 V
VOUT(S) < 1.2 V
VOUT(S) < 1.3 V
VOUT(S) < 1.4 V
VOUT(S) < 1.5 V
VOUT(S) < 1.7 V
VOUT(S) < 1.8 V
VOUT(S) < 2.0 V
VOUT(S) < 2.5 V
VOUT(S) < 2.8 V
VOUT(S) < 3.0 V
0.50
−
−
−
−
−
−
−
−
0.76
0.67
0.58
0.49
0.43
0.37
0.31
0.27
0.23
0.18
0.17
0.16
Dropout voltage*3
Vdrop
IOUT = 100 mA
−
−
−
VOUT(S)
≤
3.5 V
VOUT(S)
IOUT = 1
+
0.5 V
≤
≤
VIN
VIN
≤
≤
5.5 V,
5.5 V,
1.0 V
≤
VOUT(S)
≤
3.5 V
−
0.05
0.2
%/V
1
μA
ΔVOUT1
1.0 V
1.1 V
1.2 V
≤
≤
≤
VOUT(S) < 1.1 V
VOUT(S) < 1.2 V
−
−
−
0.07
0.06
0.05
2.0
1.0
0.2
%/V
%/V
%/V
1
1
1
Line regulation
Load regulation
ΔVIN•VOUT VOUT(S)
+
0.5 V
IOUT = 30 mA
VOUT(S)
≤
3.5 V
V
1
IN = VOUT(S) 1.0 V,
+
1.0 V
≤
VOUT(S)
≤
3.5 V
−
20
40
mV
1
μA
≤
IOUT ≤ 100 mA
1.0 V
1.1 V
1.2 V
1.3 V
1.4 V
≤
≤
≤
≤
≤
VOUT(S) < 1.1 V
VOUT(S) < 1.2 V
VOUT(S) < 1.3 V
VOUT(S) < 1.4 V
−
−
−
−
−
40
40
40
40
40
640
400
160
80
mV
mV
mV
mV
mV
1
1
1
1
1
ΔVOUT2
VIN = VOUT(S) 1.0 V,
100 IOUT ≤ 200 mA
+
μA
≤
VOUT(S)
≤
3.5 V
80
ΔVOUT
ΔTa•VOUT
V
IN = VOUT(S)
+ 1.0 V, IOUT = 30 mA,
Output voltage temperature coefficient*4
−
130
−
ppm/
°
C
1
−
40 Ta ≤ +105°C
°
C
≤
Current consumption during operation
Current consumption during power-off
Input voltage
ISS1
ISS2
VIN
VIN = VOUT(S)
VIN = VOUT(S)
+
+
1.0 V, ON / OFF pin = ON, no load
1.0 V, ON / OFF pin = OFF, no load
−
−
1.5
0.9
0.01
−
1.35
0.1
5.5
μ
A
2
2
−
μA
−
V
V
IN = VOUT(S)
+
1.0 V, RL = 1.0 kΩ,
ON / OFF pin input voltage "H"
ON / OFF pin input voltage "L"
VSH
VSL
ISH
1.0
−
−
−
V
V
4
determined by VOUT output level
V
determined by VOUT output level
IN = VOUT(S)
+ 1.0 V, RL = 1.0 kΩ,
−
0.25
4
B / D type (without constant current source pull-down)
A / C type (with constant current source pull-down)
−
0.1
−
0.1
−
0.1
0.2
0.1
−
μ
μ
μ
A
A
A
4
4
4
3
VIN = 5.5 V,
VON / OFF = 5.5 V
ON / OFF pin input current "H"
ON / OFF pin input current "L"
0.05
ISL
VIN = 5.5 V, VON / OFF = 0 V
VIN = VOUT(S) 1.0 V, ON / OFF pin = ON, VOUT = 0 V
−
0.1
Short-circuit current
Thermal shutdown detection
temperature
Thermal shutdown release temperature TSR
Discharge shunt resistance
Ishort
+
−
50
mA
TSD
Junction temperature
−
−
−
150
120
35
−
−
−
°
°
C
C
−
−
3
Junction temperature
VOUT = 0.1 V, A / B type
VIN = 5.5 V
RLOW
Ω
during power-off
(with discharge shunt function)
9
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
*1. VOUT(S): Set output voltage
VOUT(E): Actual output voltage
The output voltage when VIN = VOUT(S) + 1.0 V, IOUT = 30 mA
*2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current.
*3. Vdrop = VIN1 − (VOUT3 × 0.98)
VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input
voltage.
VOUT3 is the output voltage when VIN = VOUT(S) + 1.0 V and IOUT = 100 mA.
*4. A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
ΔVOUT
ΔTa
ΔVOUT
ΔTa•VOUT
mV/°C *1 = VOUT(S) V *2
×
ppm/°C *3 ÷ 1000
[ ]
[
]
[ ]
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
*5. Due to limitation of the power dissipation, this value may not be satisfied. Attention should be paid to the power
dissipation when the output current is large.
This specification is guaranteed by design.
10
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Test Circuits
+
VOUT
VSS
VIN
A
+
ON / OFF
V
Set to ON
Figure 9 Test Circuit 1
+
A
VOUT
VIN
ON / OFF
VSS
Set to VIN or GND
Figure 10 Test Circuit 2
VOUT
A
VIN
+
ON / OFF
V
VSS
Set to VIN or GND
Figure 11 Test Circuit 3
VOUT
VSS
VIN
+
+
ON / OFF
A
V
RL
Figure 12 Test Circuit 4
11
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Standard Circuit
Input
CIN
Output
VIN
VOUT
*1
*2
ON / OFF
CL
VSS
Single GND
GND
*1.
CIN is a capacitor for stabilizing the input.
*2. CL is a capacitor for stabilizing the output.
Figure 13
Caution The above connection diagram and constants will not guarantee successful operation. Perform
thorough evaluation including the temperature characteristics with an actual application to set the
constants.
Condition of Application
Input capacitor (CIN):
Output capacitor (CL):
A ceramic capacitor with capacitance of 0.1 μF or more is recommended.
A ceramic capacitor with capacitance of 0.1 μF or more is recommended.
Caution Generally, in a voltage regulator, an oscillation may occur depending on the selection of the external
parts. Perform thorough evaluation including the temperature characteristics with an actual
application using the above capacitors to confirm no oscillation occurs.
Selection of Input Capacitor (CIN) and Output Capacitor (CL)
The S-1313xxxH Series requires CL between the VOUT pin and the VSS pin for phase compensation. The operation is
stabilized by a ceramic capacitor with capacitance of 0.1 μF or more. When using an OS capacitor, a tantalum capacitor
or an aluminum electrolytic capacitor, the capacitance also must be 0.1 μF or more. However, an oscillation may occur
depending on the equivalent series resistance (ESR).
Moreover, the S-1313xxxH Series requires CIN between the VIN pin and the VSS pin for a stable operation.
Generally, an oscillation may occur when a voltage regulator is used under the conditon that the impedance of the power
supply is high.
Note that the output voltage transient characteristics vary depending on the capacitance of CIN and CL and the value of
ESR.
Caution Perform thorough evaluation including the temperature characteristics with an actual application to
select CIN and CL.
12
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Explanation of Terms
1. Low dropout voltage regulator
This is a voltage regulator which made dropout voltage small by its built-in low on-resistance output transistor.
2. Output voltage (VOUT
)
This voltage is output at an accuracy of 1.0% or 15 mV*2 when the input voltage, the output current and the
temperature are in a certain condition*1.
*1. Differs depending on the product.
*2. When VOUT < 1.5 V: 15 mV, when VOUT ≥1.5 V: 1.0%
Caution If the certain condition is not satisfied, the output voltage may exceed the accuracy range of
1.0% or 15 mV. Refer to Table 13 in " Electrical Characteristics" for details.
ΔVOUT1
ΔVIN • VOUT
3. Line regulation
Indicates the dependency of the output voltage on the input voltage. That is, the values show how much the output
voltage changes due to a change in the input voltage with the output current remaining unchanged.
4. Load regulation (ΔVOUT2
)
Indicates the dependency of the output voltage on the output current. That is, the values show how much the output
voltage changes due to a change in the output current with the input voltage remaining unchanged.
5. Dropout voltage (Vdrop
)
Indicates the difference between input voltage (VIN1) and the output voltage when the output voltage becomes 98% of
the output voltage value (VOUT3) at VIN = VOUT(S) + 1.0 V after the input voltage (VIN) is decreased gradually.
Vdrop = VIN1 − (VOUT3 × 0.98)
13
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
ΔVOUT
ΔTa • VOUT
6. Output voltage temperature coefficient
The shaded area in Figure 14 is the range where VOUT varies in the operation temperature range when the output
voltage temperature coefficient is 130 ppm/°C.
Example of S-1313A10H typ. product
VOUT
[V]
+0.13 mV/°C
*1
VOUT(E)
−0.13 mV/°C
−40
+25
+105
Ta [°C]
*1.
V
OUT(E) is the value of the output voltage measured at Ta = +25°C.
Figure 14
A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
ΔVOUT
ΔTa
ΔVOUT
ΔTa • VOUT
mV/°C *1 = VOUT(S) V *2
×
ppm/°C *3 ÷ 1000
[ ]
[
]
[ ]
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
14
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Operation
1. Basic operation
Figure 15 shows the block diagram of the S-1313xxxH Series to describe the basic operation.
The error amplifier compares the feedback voltage (Vfb) whose output voltage (VOUT) is divided by the feedback
resistors (Rs and Rf) with the reference voltage (Vref). The error amplifier controls the output transistor, consequently,
the regulator starts the operation that keeps VOUT constant without the influence of the input voltage (VIN).
VIN
*1
Current
supply
Error
amplifier
VOUT
−
+
Vref
Rf
Vfb
Reference voltage
circuit
Rs
VSS
*1. Parasitic diode
Figure 15
2. Output transistor
In the S-1313xxxH Series, a low on-resistance P-channel MOS FET is used between the VIN pin and the VOUT pin
as the output transistor. In order to hold VOUT constant, the on-resistance of the output transistor varies appropriately
according to the output current (IOUT).
Caution Since a parasitic diode exists between the VIN pin and the VOUT pin due to the structure of the
transistor, the IC may be damaged by a reverse current if VOUT becomes higher than VIN. Therefore,
be sure that VOUT does not exceed VIN + 0.3 V.
15
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
3. ON / OFF pin
The ON / OFF pin controls the internal circuit and the output transistor in order to start and stop the regulator. When the
ON / OFF pin is set to OFF, the internal circuit stops operating and the output transistor between the VIN pin and the
VOUT pin is turned off, reducing current consumption significantly.
Note that the current consumption increases when a voltage of 0.25 V to VIN − 0.3 V is applied to the ON / OFF pin.
The ON / OFF pin is configured as shown in Figure 16 and Figure 17.
3. 1 S-1313xxxH Series A / C type
The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS
level.
For the ON / OFF pin current, refer to the A / C type of the ON / OFF pin input current "H" in " Electrical
Characteristics".
3. 2 S-1313xxxH Series B / D type
The ON / OFF pin is not internally pulled down to the VSS pin, so do not use it in the floating status. When not using
the ON / OFF pin, connect it to the VIN pin.
Table 14
Product Type
A / B / C / D
ON / OFF Pin
"H": ON
"L": OFF
Internal Circuit
Operate
Stop
VOUT Pin Voltage
Constant value*1
Current Consumption
*2
ISS1
*3
A / B / C / D
Pulled down to VSS
ISS2
*1. The constant value is output due to the regulating based on the set output voltage value.
*2. Note that the IC's current consumption increases as much as current flows into the constant current of 0.1 μA
typ. when the ON / OFF pin is connected to the VIN pin and the S-1313xxxH Series A / C type is operating.
(refer to Figure 16).
*3. The VOUT pin voltage of the S-1313xxxH Series A / B type is pulled down to VSS due to combined resistance
(RLOW = 35 Ω typ.) of the discharge shunt circuit and the feedback resistors, and a load.
VIN
VIN
ON / OFF
ON / OFF
VSS
VSS
Figure 16 S-1313xxxH Series A / C type
Figure 17 S-1313xxxH Series B / D type
16
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
4. Discharge shunt function (S-1313xxxH Series A / B type)
The S-1313xxxH Series A / B type has a built-in discharge shunt circuit to discharge the output capacitance.
The output capacitance is discharged as follows so that the VOUT pin reaches the VSS level.
(1) The ON / OFF pin is set to OFF level.
(2) The output transistor is turned off.
(3) The discharge shunt circuit is turned on.
(4) The output capacitor discharges.
Since the S-1313xxxH Series C / D type does not have a discharge shunt circuit, the VOUT pin is set to VSS level
through several MΩ internal divided resistors between the VOUT pin and the VSS pin. The S-1313xxxH Series A / B
type allows the VOUT pin to reach the VSS level rapidly due to the discharge shunt circuit.
S-1313xxxH Series
Output transistor: OFF
*1
VOUT
VIN
Discharge shunt circuit
: ON
Output
capacitor
*1
(CL)
ON / OFF
ON / OFF circuit
ON / OFF Pin: OFF
Current flow
GND
VSS
*1. Parasitic diode
Figure 18
5. Constant current source pull-down (S-1313xxxH Series A / C type)
The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS level.
Note that the IC's current consumption increases as much as current flows into the constant current of 0.1 μA typ. when
the ON / OFF pin is connected to the VIN pin and the S-1313xxxH Series A / C type is operating.
17
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
6. Overcurrent protection circuit
The S-1313xxxH Series has a built-in overcurrent protection circuit to limit the overcurrent of the output transistor.
When the VOUT pin is shorted with the VSS pin, that is, at the time of the output short-circuit, the output current is
limited to 50 mA typ. due to the overcurrent protection circuit operation. The S-1313xxxH Series restarts regulating
when the output transistor is released from the overcurrent status.
Caution This overcurrent protection circuit does not work as for thermal protection. For example, when the
output transistor keeps the overcurrent status long at the time of output short-circuit or due to other
reasons, pay attention to the conditions of the input voltage and the load current so as not to
exceed the power dissipation.
7. Thermal shutdown circuit
The S-1313xxxH Series has a built-in thermal shutdown circuit to limit overheating. When the junction temperature
increases to 150°C typ., the thermal shutdown circuit becomes the detection status, and the regulating is stopped.
When the junction temperature decreases to 120°C typ., the thermal shutdown circuit becomes the release status,
and the regulator is restarted.
If the thermal shutdown circuit becomes the detection status due to self-heating, the regulating is stopped and VOUT
decreases. For this reason, the self-heating is limited and the temperature of the IC decreases. The thermal shutdown
circuit becomes release status when the temperature of the IC decreases, and the regulating is restarted, thus the
self-heating is generated again. Repeating this procedure makes the waveform of VOUT into a pulse-like form. This
phenomenon continues unless decreasing either or both of the input voltage and the output current in order to reduce
the internal power consumption, or decreasing the ambient temperature. Note that the product may suffer physical
damage such as deterioration if the above phenomenon occurs continuously.
Caution 1. When the heat radiation of the application is not in a good condition, the self-heating cannot be
limited immediately, and the IC may suffer physical damage. Perform thorough evaluation
including the temperature characteristics with an actual application to confirm no problems
happen.
2. If a large load current flows during the restart process of regulating after the thermal shutdown
circuit changes to the release status from the detection status, the thermal shutdown circuit
becomes the detection status again due to self-heating, and a problem may happen in the restart
of regulating. A large load current, for example, occurs when charging to the CL whose
capacitance is large.
Perform thorough evaluation including the temperature characteristics with an actual application
to select CL.
Table 15
Thermal Shutdown Circuit
VOUT Pin Voltage
Constant value*2
Pulled down to VSS
Release: 120°C typ.*1
Detection: 150°C typ.*1
*3
*1. Junction temperature
*2. The constant value is output due to the regulating based on the set output voltage value.
*3. The VOUT pin voltage is pulled down to VSS due to the feedback resistors (Rs and Rf) and a load.
18
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
8. Thermal shutdown circuit stop function
The S-1313xxxH Series has a thermal shutdown circuit stop function during low load current.
When the load current is approx. 0.2 mA or less, the current that flows in the thermal shutdown circuit is stopped and
the thermal shutdown circuit stops operating. This makes the super low current consumption operation possible.
When the load current is approx. 0.5 mA or more, a current is applied to the thermal shutdown circuit, thus making the
protection operation possible.
7.0
6.0
Operation at super low current consumption
5.0
4.0
3.0
2.0
Thermal shutdown circuit operating
1.0
0
0
0.5
1.0
1.5
2.0
2.5
3.0
I
OUT [mA]
Figure 19
19
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Precautions
• Generally, when a voltage regulator is used under the condition that the load current value is small (10 μA or less), the
output voltage may increase due to the leakage current of an output transistor.
• Generally, when a voltage regulator is used under the condition that the temperature is high, the output voltage may
increase due to the leakage current of an output transistor.
• Generally, when the ON / OFF pin is used under the condition of OFF, the output voltage may increase due to the
leakage current of an output transistor.
• Generally, when a voltage regulator is used under the condition that the impedance of the power supply is high, an
oscillation may occur. Perform thorough evaluation including the temperature characteristics with an actual application
to select CIN.
• Generally, in a voltage regulator, an oscillation may occur depending on the selection of the external parts. The
following use conditions are recommended in the S-1313xxxH Series, however, perform thorough evaluation including
the temperature characteristics with an actual application to select CIN and CL.
Input capacitor (CIN):
A ceramic capacitor with capacitance of 0.1 μF or more is recommended.
Output capacitor (CL): A ceramic capacitor with capacitance of 0.1 μF or more is recommended.
• Ringing may occur when these three conditions below are satisfied. Before selecting an input capacitor, be sure to
evaluate sufficiently under the actual usage conditions, including the temperature characteristics.
The power supply inductance is high.
The load current is 100 mA or more.
The difference between the input voltage and the output voltage is close to the value of dropout voltage.
• Generally, in a voltage regulator, the values of an overshoot and an undershoot in the output voltage vary depending
on the variation factors of input voltage start-up, input voltage fluctuation and load fluctuation etc., or the capacitance of
CIN or CL and the value of the equivalent series resistance (ESR), which may cause a problem to the stable operation.
Perform thorough evaluation including the temperature characteristics with an actual application to select CIN and CL.
• Generally, in a voltage regulator, an overshoot may occur in the output voltage momentarily if the input voltage steeply
changes when the input voltage is started up or the input voltage fluctuates etc. Perform thorough evaluation including
the temperature characteristics with an actual application to confirm no problems happen.
• Generally, in a voltage regulator, if the VOUT pin is steeply shorted with GND, a negative voltage exceeding the
absolute maximum ratings may occur in the VOUT pin due to resonance phenomenon of the inductance and the
capacitance including CL on the application. The resonance phenomenon is expected to be weakened by inserting a
series resistor into the resonance path, and the negative voltage is expected to be limited by inserting a protection
diode between the VOUT pin and the VSS pin.
• If the input voltage is started up steeply under the condition that the capacitance of CL is large, the thermal shutdown
circuit may be in the detection status by self-heating due to the charge current to CL.
• Make sure of the conditions for the input voltage, output voltage and the load current so that the internal loss does not
exceed the power dissipation.
• Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
protection circuit.
• When considering the output current value that the IC is able to output, make sure of the output current value specified
in Table 13 in " Electrical Characteristics" and footnote *5 of the table.
• Wiring patterns on the application related to the VIN pin, the VOUT pin and the VSS pin should be designed so that the
impedance is low. When mounting CIN between the VIN pin and the VSS pin and CL between the VOUT pin and the
VSS pin, connect the capacitors as close as possible to the respective destination pins of the IC.
• In the package equipped with heat sink of backside, mount the heat sink firmly. Since the heat radiation differs
according to the condition of the application, perform thorough evaluation with an actual application to confirm no
problems happen.
• ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by products
including this IC of patents owned by a third party.
20
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Characteristics (Typical Data)
1. Output voltage vs. Output current (When load current increases) (Ta = +25°C)
1. 1 VOUT = 1.0 V
1. 2 VOUT = 2.5 V
1.2
1.0
0.8
3.0
2.5
V
IN = 3.0 V
V
IN = 2.0 V
V
IN = 4.5 V
2.0
1.5
1.0
0.5
0
V
IN = 2.8 V
V
IN = 1.3 V
0.6
0.4
0.2
0
V
IN = 3.0 V
V
IN = 5.5 V
V
IN = 3.5 V
V
IN = 5.5 V
V
IN = 1.5 V
300
0
100
200
400 500
0
100
200
300
400 500
IOUT [mA]
IOUT [mA]
1. 3 VOUT = 3.5 V
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
Remark In determining the output current, attention should
V
V
V
V
IN = 3.8 V
IN = 4.0 V
IN = 4.5 V
IN = 5.5 V
be paid to the following.
1. The minimum output current value and
footnote *5 in Table 13 in " Electrical
Characteristics"
2. The power dissipation
0
100
200
300
400
500
IOUT [mA]
2. Output voltage vs. Input voltage (Ta = +25°C)
2. 1 VOUT = 1.0 V
2. 2 VOUT = 2.5 V
1.2
1.1
1.0
2.7
2.6
2.5
2.4
I
OUT = 1 mA
I
OUT = 1 mA
0.9
0.8
0.7
0.6
I
I
OUT = 30 mA
OUT = 50 mA
2.3
2.2
2.1
2.0
I
OUT = 30 mA
I
OUT = 50 mA
I
OUT = 100 mA
I
OUT = 100 mA
0.6
1.0
1.4
1.8 2.2
2.6
2.0
2.5
3.0
3.5
4.0
4.5
V
IN [V]
VIN [V]
2. 3 VOUT = 3.5 V
3.7
3.6
3.5
3.4
3.3
3.2
3.1
3.0
I
OUT = 1 mA
I
OUT = 30 mA
OUT = 50 mA
I
I
OUT = 100 mA
3.0
3.5
4.0 4.5
5.0
5.5
V
IN [V]
21
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
3. Dropout voltage vs. Output current
3. 1 VOUT = 1.0 V
3. 2 VOUT = 2.5 V
1.4
1.2
1.0
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
Ta =
+105°C
Ta =
Ta = 25
Ta = 40
+105°C
Ta = 25°C
+
+
°C
Ta =
−40°C
0.8
−
°C
0.6
0.4
0.2
0
0
25 50 75 100 125 150 175 200
0
25 50 75 100 125 150 175 200
I
OUT [mA]
IOUT [mA]
3. 3
VOUT = 3.5 V
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
Ta = +105
Ta = 25
Ta = 40
°C
+
°C
°C
−
0
25 50 75 100 125 150 175 200
I
OUT [mA]
4. Dropout voltage vs. Set output voltage
1.2
I
OUT = 200 mA
OUT = 100 mA
OUT = 50 mA
OUT = 30 mA
1.0
0.8
0.6
0.4
0.2
0
I
I
I
I
OUT = 10 mA
I
OUT = 1 mA
OUT = 0.1 mA
I
1.0
1.5
2.0
2.5
3.0
3.5
V
OUT(S) [V]
22
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
5. Output voltage vs. Ambient temperature
5. 1 VOUT = 1.0 V
5. 2 VOUT = 2.5 V
1.10
1.05
1.00
0.95
0.90
2.7
2.6
2.5
2.4
2.3
−40
−25
0
25
50
75
105
−
40
−
25
0
25
50
75
105
Ta [°C]
Ta [°C]
5. 3 VOUT = 3.5 V
3.8
3.7
3.6
3.5
3.4
3.3
3.2
−
40
−
25
0
25
Ta [°C]
50
75
105
6. Current consumption vs. Input voltage
6. 1 VOUT = 1.0 V
6. 2 VOUT = 2.5 V
2.00
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
Ta = +105°C
Ta = +105°C
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
Ta = +25°C
Ta = +25°C
Ta = −40°C
Ta = −40°C
0
1
2
3
4
5
6
0
1
2
3
4
5
6
VIN [V]
VIN [V]
6. 3 VOUT = 3.5 V
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
Ta =
+105°C
Ta = 25°C
+
Ta = −40°C
0
1
2
3
4
5
6
VIN [V]
23
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
7. Current consumption vs. Ambient temperature
7. 1 VOUT = 1.0 V
7. 2 VOUT = 2.5 V
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
VIN = 5.5 V
VIN = 5.5 V
V
IN = 2.0 V
VIN = 3.5 V
−40
−25
0
25
50
75
105
−40
−25
0
25
50
75
105
Ta [°C]
Ta [°C]
7. 3 VOUT = 3.5 V
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
VIN = 5.5 V
V
IN = 4.5 V
−40
−25
0
25
50
75
105
Ta [°C]
8. Current consumption vs. Output current
8. 1 VOUT = 1.0 V
8. 2 VOUT = 2.5 V
40
35
40
35
30
25
20
15
10
5
V
IN = 2.0 V
V
IN = 3.5 V
30
25
20
15
10
5
V
IN = 5.5 V
VIN = 5.5 V
0
0
0
40
80
120
160
200
0
40
80
120
160
200
IOUT [mA]
IOUT [mA]
8. 3 VOUT = 3.5 V
40
35
30
25
20
15
10
5
V
IN = 4.5 V
V
IN = 5.5 V
160
0
0
40
80
120
200
IOUT [mA]
24
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Reference Data
1. Transient response characteristics when input (Ta = +25°C)
1. 1 VOUT = 1.0 V
IOUT = 1 mA, CIN = CL = 0.1
μF, VIN = 2.0 V
↔
3.0 V, tr = tf = 5.0
μs
IOUT = 100 mA, CIN = CL = 0.1 μF, VIN = 2.0 V ↔ 3.0 V, tr = tf = 5.0 μs
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
V
IN
V
IN
V
OUT
VOUT
−40 −20
0
20 40 60 80 100 120 140
−40 −20
0
20 40 60 80 100 120 140
t [μs]
t [μs]
1. 2 VOUT = 2.5 V
IOUT = 1 mA, CIN = CL = 0.1
μF, VIN = 3.5 V
↔
4.5 V, tr = tf = 5.0
μs
IOUT = 100 mA, CIN = CL = 0.1 μF, VIN = 3.5 V ↔ 4.5 V, tr = tf = 5.0 μs
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
3.1
3.0
2.9
2.8
2.7
2.6
2.5
2.4
2.3
3.1
3.0
2.9
2.8
2.7
2.6
2.5
2.4
2.3
V
IN
V
IN
V
OUT
VOUT
−40 −20
0
20 40 60 80 100 120 140
−40 −20
0
20 40 60 80 100 120 140
t [μs]
t [μs]
1. 3 VOUT = 3.5 V
IOUT = 1 mA, CIN = CL = 0.1
μF, VIN = 4.5 V
↔
5.5 V, tr = tf = 5.0
μs
IOUT = 100 mA, CIN = CL = 0.1 μF, VIN = 4.5 V ↔ 5.5 V, tr = tf = 5.0 μs
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
4.1
4.0
3.9
3.8
3.7
3.6
3.5
3.4
3.3
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
4.1
4.0
3.9
3.8
3.7
3.6
3.5
3.4
3.3
V
IN
V
IN
VOUT
V
OUT
−40 −20
0
20 40 60 80 100 120 140
−40 −20
0
20 40 60 80 100 120 140
t [μs]
t [μs]
25
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
2. Transient response characteristics of load (Ta = +25°C)
2. 1 VOUT = 1.0 V
VIN = 2.0 V, CIN = CL = 0.1 μF, IOUT = 1 mA ↔ 50 mA
VIN = 2.0 V, CIN = CL = 0.1 μF, IOUT = 50 mA ↔ 100 mA
100
50
2.6
2.2
1.8
1.4
1.0
0.6
0.2
150
100
50
2.6
2.2
1.8
1.4
1.0
0.6
0.2
I
OUT
I
OUT
0
0
−50
−100
−150
−200
V
OUT
V
OUT
−50
−100
−150
−100 −50
0
50 100 150 200 250 300
−200 −100
0
100 200 300 400 500 600
t [μs]
t [μs]
2. 2
VOUT = 2.5 V
VIN = 3.5 V, CIN = CL = 0.1 μF, IOUT = 1 mA ↔ 50 mA
VIN = 3.5 V, CIN = CL = 0.1 μF, IOUT = 50 mA ↔ 100 mA
100
50
150
100
50
4.9
4.3
3.7
3.1
2.5
1.9
1.3
3.7
3.4
3.1
2.8
2.5
2.2
1.9
I
OUT
IOUT
0
−50
−100
−150
−200
0
V
OUT
VOUT
−50
−100
−150
−0.4 −0.2 0 0.2 0.4 0.6 0.8
1
1.2 1.4
−200−100 0 100 200 300 400 500 600 700
t [μs]
t [ms]
2. 3 VOUT = 3.5 V
VIN = 4.5 V, CIN = CL = 0.1 μF, IOUT = 1 mA ↔ 50 mA
VIN = 4.5 V, CIN = CL = 0.1 μF, IOUT = 50 mA ↔ 100 mA
100
50
150
100
50
6.3
5.6
4.9
4.2
3.5
2.8
2.1
4.7
4.4
4.1
3.8
3.5
3.2
2.9
I
OUT
IOUT
0
−50
−100
−150
−200
0
V
OUT
VOUT
−50
−100
−150
−0.4 −0.2 0 0.2 0.4 0.6 0.8
1
1.2 1.4
−200−100 0 100 200 300 400 500 600 700
t [μs]
t [ms]
26
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
3. Transient response characteristics of ON / OFF pin (Ta = +25°C)
3. 1 VOUT = 1.0 V
VIN = 2.0 V, CIN = CL = 0.1
μF, IOUT = 1 mA, VON / OFF = 0 V
→
2 V, tr = 1.0
μs
VIN = 2.0 V, CIN = CL = 0.1
μF, IOUT = 100 mA, VON / OFF = 0 V
→
2 V, tr = 1.0 μs
2.5
2.0
1.5
1.0
0.5
0
2.5
2.0
1.5
1.0
0.5
0
4
4
VON / OFF
VOUT
V
ON / OFF
OUT
2
0
2
0
V
−2
−4
−6
−8
−2
−4
−6
−8
−0.5
−0.5
−100
0
100
200
300
400
−100
0
100
200
300
400
t [μs]
t [μs]
3. 2 VOUT = 2.5 V
VIN = 3.5 V, CIN = CL = 0.1
μF, IOUT = 100 mA, VON / OFF = 0 V
→
3.5 V, tr = 1.0 μs
VIN = 3.5 V, CIN = CL = 0.1
μF, IOUT = 1 mA, VON / OFF = 0 V
→
3.5 V, tr = 1.0 μs
10
8
10
8
6
6
V
ON / OFF
V
ON / OFF
4
4
6
2
6
2
4
0
4
0
V
OUT
V
OUT
2
2
−2
−4
−6
−2
−4
−6
0
0
−2
−2
−200
0
200 400 600 800 1000
−200
0
200 400 600 800 1000
t [μs]
t [μs]
3. 3 VOUT = 3.5 V
VIN = 4.5 V, CIN = CL = 0.1
μF, IOUT = 100 mA, VON / OFF = 0 V
→
4.5 V, tr = 1.0 μs
VIN = 4.5 V, CIN = CL = 0.1
μF, IOUT = 1 mA, VON / OFF = 0 V
→
4.5 V, tr = 1.0 μs
14
12
10
8
14
12
10
8
8
6
4
8
6
4
V
ON / OFF
V
ON / OFF
2
2
6
4
2
0
6
4
2
0
0
0
V
OUT
V
OUT
−2
−4
−6
−8
−2
−4
−6
−8
−2
−2
−200
0
200 400 600 800 1000
−200
0
200 400 600 800 1000
t [μs]
t [μs]
27
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
4. Output capacitance vs. Characteristics of discharge time (Ta = +25°C)
1 μs
VIN = VOUT + 1.0 V, IOUT = no load,
VON / OFF = VOUT + 1.0 V → VSS, tf = 1 μs
VON / OFF
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
V
V
V
OUT(S) = 1.0 V
OUT(S) = 2.5 V
OUT(S) = 3.5 V
VSS
tDSC
VOUT
0
2
4
6
8
10
12
VOUT × 10%
CL [μF]
VIN = VOUT + 1.0 V
VON / OFF = VOUT + 1.0 V → VSS
Figure 20 S-1313xxxH Series A / B type
(with discharge shunt function)
Figure 21 Measurement Condition of Discharge Time
5. Ripple rejection (Ta = +25°C)
5. 1 VOUT = 1.0 V
5. 2 VOUT = 2.5 V
VIN = 2.0 V, CL = 0.1 μF
VIN = 3.5 V, CL = 0.1 μF
100
90
100
90
IOUT = 1 mA
IOUT = 30 mA
IOUT = 100 mA
IOUT = 1 mA
80
70
60
50
40
30
20
10
0
80
70
60
50
40
30
20
10
0
IOUT = 30 mA
IOUT = 100 mA
IOUT = 200 mA
10
100
1k
10k
100k
1M
10
100
1k
10k
100k
1M
Frequency [Hz]
Frequency [Hz]
5. 3 VOUT = 3.5 V
VIN = 4.5 V, CL = 0.1 μF
100
90
80
70
60
50
40
30
20
10
0
I
I
I
I
OUT = 1 mA
OUT = 30 mA
OUT = 100 mA
OUT = 200 mA
10
100
1k
10k
100k
1M
Frequency [Hz]
28
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
6. Example of equivalent series resistance vs. Output current characteristics (Ta = +25°C)
CIN = CL = 0.1 μF
100
VIN
VOUT
CIN
Stable
S-1313xxxH
Series
*1
CL
ON / OFF
VSS
0
RESR
0.01
240
I
OUT [mA]
*1. CL: Murata Manufacturing Co., Ltd. GRM31CR72E104K (0.1 μF)
Figure 22
Figure 23
29
105°C OPERATION, 5.5 V INPUT, 200 mA VOLTAGE REGULATOR
S-1313xxxH Series
Rev.1.2_00
Power Dissipation
SOT-23-5
SC-82AB
T
j
= +125°C max.
T
j
= +125°C max.
1.0
0.8
0.6
0.4
0.2
0.0
1.0
0.8
0.6
0.4
0.2
0.0
B
A
B
A
0
25
50
75
100 125 150 175
0
25
50
75
100 125 150 175
Ambient temperature (Ta) [°C]
Ambient temperature (Ta) [°C]
Board
Power Dissipation (PD)
Board
Power Dissipation (PD)
A
B
C
D
E
0.52 W
A
B
C
D
E
0.42 W
0.63 W
0.49 W
−
−
−
−
−
−
HSNT-4(1010)
HSNT-4(0808)
Tj
= +125°C max.
Tj = +125°C max.
1.0
0.8
0.6
1.0
0.8
0.6
0.4
0.2
0.0
0.4
B
B
A
A
0.2
0.0
0
25
50
75
100 125 150 175
0
25
50
75
100 125 150 175
Ambient temperature (Ta) [°C]
Ambient temperature (Ta) [°C]
Board
Power Dissipation (PD)
Board
Power Dissipation (PD)
A
B
C
D
E
0.26 W
A
B
C
D
E
0.25 W
0.32 W
0.30 W
−
−
−
−
−
−
30
SOT-23-3/3S/5/6 Test Board
No. SOT23x-A-Board-SD-2.0
ABLIC Inc.
SC-82AB Test Board
No. SC82AB-A-Board-SD-1.0
ABLIC Inc.
HSNT-4(1010) Test Board
No. HSNT4-B-Board-SD-1.0
ABLIC Inc.
HSNT-4(0808) Test Board
No. HSNT4-A-Board-SD-1.0
ABLIC Inc.
2.9±0.2
1.9±0.2
4
5
+0.1
-0.06
1
2
3
0.16
0.95±0.1
0.4±0.1
No. MP005-A-P-SD-1.3
TITLE
SOT235-A-PKG Dimensions
MP005-A-P-SD-1.3
No.
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.1(10 pitches:40.0±0.2)
+0.1
-0
2.0±0.05
0.25±0.1
ø1.5
+0.2
-0
4.0±0.1
ø1.0
1.4±0.2
3.2±0.2
3
4
2 1
5
Feed direction
No. MP005-A-C-SD-2.1
TITLE
SOT235-A-Carrier Tape
MP005-A-C-SD-2.1
No.
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. MP005-A-R-SD-1.1
TITLE
SOT235-A-Reel
MP005-A-R-SD-1.1
No.
ANGLE
UNIT
QTY.
3,000
mm
ABLIC Inc.
2.0±0.2
1.3±0.2
4
3
0.05
+0.1
-0.06
0.16
2
1
+0.1
-0.05
0.4
+0.1
-0.05
0.3
No. NP004-A-P-SD-2.0
TITLE
No.
SC82AB-A-PKG Dimensions
NP004-A-P-SD-2.0
ANGLE
UNIT
mm
ABLIC Inc.
2.0±0.05
+0.1
-0
1.1±0.1
ø1.5
4.0±0.1
4.0±0.1
0.2±0.05
ø1.05±0.1
(0.7)
2.2±0.2
2
3
1
4
Feed direction
No. NP004-A-C-SD-3.0
SC82AB-A-Carrier Tape
NP004-A-C-SD-3.0
TITLE
No.
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. NP004-A-R-SD-1.1
TITLE
No.
SC82AB-A-Reel
NP004-A-R-SD-1.1
QTY.
ANGLE
UNIT
3,000
mm
ABLIC Inc.
0.38±0.02
0.65
3
4
+0.05
-0.02
1
2
0.08
1.00±0.04
he heat sink of back side has different electric
potential depending on the product.
Confirm specifications of each product.
Do not use it as the function of electrode.
0.20±0.05
No. PL004-A-P-SD-1.1
TITLE
HSNT-4-B-PKG Dimensions
PL004-A-P-SD-1.1
No.
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.05
2.0±0.05
+0.1
-0
ø1.5
0.25±0.05
+0.1
-0
ø0.5
2.0±0.05
0.5±0.05
1.12±0.05
2
3
1
4
Feed direction
No. PL004-A-C-SD-2.0
HSNT-4-B-Carrier Tape
PL004-A-C-SD-2.0
TITLE
No.
ANGLE
UNIT
mm
ABLIC Inc.
+1.0
- 0.0
9.0
11.4±1.0
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. PL004-A-R-SD-1.0
HSNT-4-B-Reel
PL004-A-R-SD-1.0
TITLE
No.
QTY.
10,000
ANGLE
UNIT
mm
ABLIC Inc.
Land Pattern
0.30min.
0.38~0.48
0.38~0.48
0.07
0.65±0.02
(1.02)
Caution It is recommended to solder the heat sink to a board
in order to ensure the heat radiation.
PKG
Metal Mask Pattern
Aperture ratio
Aperture ratio
Caution
Mask aperture ratio of the lead mounting part is 100%.
Mask aperture ratio of the heat sink mounting part is 40%.
Mask thickness: t0.10mm to 0.12 mm
100%
40%
t0.10mm ~ 0.12 mm
HSNT-4-B
TITLE
-Land Recommendation
No. PL004-A-L-SD-2.0
No.
PL004-A-L-SD-2.0
ANGLE
UNIT
mm
ABLIC Inc.
0.38±0.02
0.40
3
4
+0.05
-0.02
1
2
0.08
0.80±0.04
The heat sink of back side has different electric
potential depending on the product.
Confirm specifications of each product.
Do not use it as the function of electrode.
0.20±0.05
No. PK004-A-P-SD-2.1
TITLE
HSNT-4-A-PKG Dimensions
PK004-A-P-SD-2.1
No.
ANGLE
mm
UNIT
ABLIC Inc.
4.0±0.05
2.0±0.05
+0.1
-0
ø1.5
0.25±0.05
+0.1
-0
2.0±0.05
ø0.5
0.5±0.05
0.93±0.05
2
3
1
4
Feed direction
No. PK004-A-C-SD-3.0
HSNT-4-A-Carrier Tape
PK004-A-C-SD-3.0
TITLE
No.
ANGLE
mm
UNIT
ABLIC Inc.
+1.0
- 0.0
9.0
11.4±1.0
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. PK004-A-R-SD-2.0
HSNT-4-A-Reel
TITLE
No.
PK004-A-R-SD-2.0
ANGLE
QTY.
10,000
mm
UNIT
ABLIC Inc.
Land Pattern
0.22min.
0.27~0.32
0.27~0.32
0.05
0.40±0.02
(0.82)
Caution It is recommended to solder the heat sink to a board
in order to ensure the heat radiation.
PKG
Metal Mask Pattern
Aperture ratio
Aperture ratio
Caution
Mask aperture ratio of the lead mounting part is 100%.
Mask aperture ratio of the heat sink mounting part is 40%.
Mask thickness: t0.10mm to 0.12 mm
100%
40%
t0.10mm ~ 0.12 mm
HSNT-4-A
TITLE
-Land Recommendation
No.
PK004-A-L-SD-3.0
ANGLE
No. PK004-A-L-SD-3.0
mm
UNIT
ABLIC Inc.
Disclaimers (Handling Precautions)
1. All the information described herein (product data, specifications, figures, tables, programs, algorithms and
application circuit examples, etc.) is current as of publishing date of this document and is subject to change without
notice.
2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the reasons other than the products
described herein (hereinafter "the products") or infringement of third-party intellectual property right and any other
right due to the use of the information described herein.
3. ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the incorrect information described
herein.
4. Be careful to use the products within their ranges described herein. Pay special attention for use to the absolute
maximum ratings, operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by failures and / or accidents, etc. due to
the use of the products outside their specified ranges.
5. Before using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6. When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7. The products are strictly prohibited from using, providing or exporting for the purposes of the development of
weapons of mass destruction or military use. ABLIC Inc. is not liable for any losses, damages, claims or demands
caused by any provision or export to the person or entity who intends to develop, manufacture, use or store nuclear,
biological or chemical weapons or missiles, or use any other military purposes.
8. The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses by
ABLIC, Inc. Do not apply the products to the above listed devices and equipments.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by unauthorized or unspecified use of
the products.
9. In general, semiconductor products may fail or malfunction with some probability. The user of the products should
therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread
prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social
damage, etc. that may ensue from the products' failure or malfunction.
The entire system in which the products are used must be sufficiently evaluated and judged whether the products are
allowed to apply for the system on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc. The information
described herein does not convey any license under any intellectual property rights or any other rights belonging to
ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any part of this
document described herein for the purpose of disclosing it to a third-party is strictly prohibited without the express
permission of ABLIC Inc.
14. For more details on the information described herein or any other questions, please contact ABLIC Inc.'s sales
representative.
15. This Disclaimers have been delivered in a text using the Japanese language, which text, despite any translations into
the English language and the Chinese language, shall be controlling.
2.4-2019.07
www.ablic.com
相关型号:
©2020 ICPDF网 联系我们和版权申明