S-1167B40-M5T1X [ABLIC]
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR;型号: | S-1167B40-M5T1X |
厂家: | ABLIC |
描述: | ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR |
文件: | 总31页 (文件大小:546K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
S-1167 Series
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION
AND LOW DROPOUT CMOS VOLTAGE REGULATOR
www.ablic.com
© ABLIC Inc., 2004-2015
Rev.3.2_02
The S-1167 Series is a positive voltage regulator with ultra low current consumption, high ripple rejection, low dropout
voltage and high-accuracy output voltage developed based on CMOS technology.
Although current consumption is very small with 9 A typ., the S-1167 Series realized the 70 dB of high ripple rejection rate.
Besides, a ceramic capacitor of 1.0 F can be used as the input and output capacitors.
Moreover, dropout voltage is also small since output voltage accuracy realizes 1.0% of high accuracy, and the low-on-
resistance transistor is built-in. A built-in overcurrent protection circuit prevents that the load current from exceeding the
current capacity of the output transistor. The ON / OFF circuit ensures long battery life.
Two packages, SOT-23-5 and SNT-6A(H) are available.
Compared with the voltage regulators using the conventional CMOS technology, the S-1167 Series is the most suitable for
the portable equipments with ultra low current consumption and corresponding to the small package.
Features
• Output voltage:
1.5 V to 5.5 V, selectable in 0.1 V step
• Input voltage:
2.0 V to 6.5 V
• Output voltage accuracy:
• Dropout voltage:
1.0%
150 mV typ. (3.0 V output product, IOUT = 100 mA)
• Current consumption:
During operation:
During power-off:
9 A typ., 16 A max.
0.1 A typ., 0.9 A max.
• Output current:
• Input and output capacitors:
• Ripple rejection:
• Built-in overcurrent protection circuit:
• Built-in ON / OFF circuit:
• Operation temperature range:
• Lead-free, Sn 100%, halogen-free*2
Possible to output 150 mA (VIN VOUT(S) 1.0 V)*1
A ceramic capacitor of 1.0 F or more can be used.
70 dB typ. (3.0 V output product, f = 1.0 kHz)
Limits overcurrent of output transistor.
Ensures long battery life.
Ta = 40°C to 85°C
*1. Attention should be paid to the power dissipation of the package when the output current is large.
*2. Refer to “ Product Name Structure” for details.
Applications
• Constant-voltage power supply for battery-powered device
• Constant-voltage power supply for cellular phone
• Constant-voltage power supply for portable equipment
Packages
• SOT-23-5
• SNT-6A(H)
1
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
Block Diagram
*1
VIN
VOUT
Overcurrent
protection circuit
ON / OFF
circuit
ON / OFF
Reference
voltage circuit
VSS
*1. Parasitic diode
Figure 1
2
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
Product Name Structure
Users can select the product type, output voltage, and package type for the S-1167 Series. Refer to “1. Product
Name” regarding the contents of product name, “2. Packages” regarding the package drawings and “3. Product
Name List” regarding details of product name.
1. Product Name
1. 1 SOT-23-5
S-1167
x
xx
-
M5T1
x
Environmental code
U
G
: Lead-free (Sn 100%), halogen-free
: Lead-free (for details, please contact our sales office)
Package abbreviation and packing specifications*1
M5T1 : SOT-23-5, Tape
Output voltage
15 to 55
(e.g. When the output voltage is 1.5 V, it is expressed as 15.)
Product type *2
A : ON / OFF pin negative logic
B : ON / OFF pin positive logic
1. 2 SNT-6A(H)
S-1167
x
xx
-
I6T2
U
Environmental code
U
: Lead-free (Sn 100%), halogen-free
Package abbreviation and packing specifications*1
I6T2 : SNT-6A(H), Tape
Output voltage
15 to 55
(e.g. When the output voltage is 1.5 V, it is expressed as 15.)
Product type *2
A : ON / OFF pin negative logic
B : ON / OFF pin positive logic
*1. Refer to the tape drawing.
*2. Refer to “3. ON / OFF Pin” in “ Operation”.
3
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
2. Packages
Drawing Code
Package Name
Package
Tape
Reel
Land
SOT-23-5
MP005-A-P-SD
PI006-A-P-SD
MP005-A-C-SD
PI006-A-C-SD
MP005-A-R-SD
PI006-A-R-SD
SNT-6A(H)
PI006-A-L-SD
3. Product Name List
3. 1 S-1167 Series A type
Table 1
Output Voltage
1.5 V1.0%
1.85 V1.0%
1.9 V1.0%
3.0 V1.0%
3.3 V1.0%
3.6 V1.0%
5.0 V1.0%
SOT-23-5
S-1167A15-M5T1x
S-1167A1J-M5T1x
S-1167A19-M5T1x
S-1167A30-M5T1x
S-1167A33-M5T1x
S-1167A36-M5T1x
S-1167A50-M5T1x
Remark 1. Please contact our sales office for the products other than those above.
2. x: G or U
3. Please select products of environmental code = U for Sn 100%, halogen-free products.
4
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
3. 2 S-1167 Series B type
Table 2
Output Voltage
1.5 V1.0%
1.6 V1.0%
1.7 V1.0%
1.8 V1.0%
1.9 V1.0%
2.0 V1.0%
2.1 V1.0%
2.2 V1.0%
2.3 V1.0%
2.4 V1.0%
2.5 V1.0%
2.6 V1.0%
2.7 V1.0%
2.8 V1.0%
2.9 V1.0%
3.0 V1.0%
3.1 V1.0%
3.2 V1.0%
3.3 V1.0%
3.4 V1.0%
3.5 V1.0%
3.6 V1.0%
3.7 V1.0%
3.8 V1.0%
3.9 V1.0%
4.0 V1.0%
4.1 V1.0%
4.2 V1.0%
4.3 V1.0%
4.4 V1.0%
4.5 V1.0%
4.6 V1.0%
4.7 V1.0%
4.8 V1.0%
4.9 V1.0%
5.0 V1.0%
5.1 V1.0%
5.2 V1.0%
5.3 V1.0%
5.4 V1.0%
5.5 V1.0%
SOT-23-5
SNT-6A(H)
S-1167B15-M5T1x
S-1167B16-M5T1x
S-1167B17-M5T1x
S-1167B18-M5T1x
S-1167B19-M5T1x
S-1167B20-M5T1x
S-1167B21-M5T1x
S-1167B22-M5T1x
S-1167B23-M5T1x
S-1167B24-M5T1x
S-1167B25-M5T1x
S-1167B26-M5T1x
S-1167B27-M5T1x
S-1167B28-M5T1x
S-1167B29-M5T1x
S-1167B30-M5T1x
S-1167B31-M5T1x
S-1167B32-M5T1x
S-1167B33-M5T1x
S-1167B34-M5T1x
S-1167B35-M5T1x
S-1167B36-M5T1x
S-1167B37-M5T1x
S-1167B38-M5T1x
S-1167B39-M5T1x
S-1167B40-M5T1x
S-1167B41-M5T1x
S-1167B42-M5T1x
S-1167B43-M5T1x
S-1167B44-M5T1x
S-1167B45-M5T1x
S-1167B46-M5T1x
S-1167B47-M5T1x
S-1167B48-M5T1x
S-1167B49-M5T1x
S-1167B50-M5T1x
S-1167B51-M5T1x
S-1167B52-M5T1x
S-1167B53-M5T1x
S-1167B54-M5T1x
S-1167B55-M5T1x
S-1167B15-I6T2U
S-1167B16-I6T2U
S-1167B17-I6T2U
S-1167B18-I6T2U
S-1167B19-I6T2U
S-1167B20-I6T2U
S-1167B21-I6T2U
S-1167B22-I6T2U
S-1167B23-I6T2U
S-1167B24-I6T2U
S-1167B25-I6T2U
S-1167B26-I6T2U
S-1167B27-I6T2U
S-1167B28-I6T2U
S-1167B29-I6T2U
S-1167B30-I6T2U
S-1167B31-I6T2U
S-1167B32-I6T2U
S-1167B33-I6T2U
S-1167B34-I6T2U
S-1167B35-I6T2U
S-1167B36-I6T2U
S-1167B37-I6T2U
S-1167B38-I6T2U
S-1167B39-I6T2U
S-1167B40-I6T2U
S-1167B41-I6T2U
S-1167B42-I6T2U
S-1167B43-I6T2U
S-1167B44-I6T2U
S-1167B45-I6T2U
S-1167B46-I6T2U
S-1167B47-I6T2U
S-1167B48-I6T2U
S-1167B49-I6T2U
S-1167B50-I6T2U
S-1167B51-I6T2U
S-1167B52-I6T2U
S-1167B53-I6T2U
S-1167B54-I6T2U
S-1167B55-I6T2U
Remark 1. Please contact our sales office for the products other than those above.
2. x: G or U
3. Please select products of environmental code = U for Sn 100%, halogen-free products.
5
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
Pin Configurations
Table 3
SOT-23-5
Top view
Pin No.
Symbol
VIN
Pin Description
Input voltage pin
5
4
1
2
3
4
5
VSS
GND pin
ON / OFF
NC*1
ON / OFF pin
No connection
Output voltage pin
VOUT
*1. The NC pin is electrically open.
The NC pin can be connected to the VIN pin or the
VSS pin.
1
2
3
Figure 2
Table 4
SNT-6A(H)
Top view
Pin No.
Symbol
VOUT
VSS
Pin Description
Output voltage pin
GND pin
1
2
3
4
5
6
1
6
5
4
NC*1
No connection
ON / OFF pin
GND pin
2
3
ON / OFF
VSS
VIN
Input voltage pin
Figure 3
*1. The NC pin is electrically open.
The NC pin can be connected to the VIN pin or the
VSS pin.
6
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
Absolute Maximum Ratings
Table 5
(Ta = 25°C unless otherwise specified)
Item
Input voltage
Symbol
VIN
Absolute Maximum Rating
Unit
V
VSS 0.3 to VSS 7
VSS 0.3 to VIN 0.3
VSS 0.3 to VIN 0.3
VON / OFF
VOUT
V
Output voltage
V
300 (When not mounted on board)
mW
mW
mW
°C
SOT-23-5
Power dissipation
PD
600*1
500*1
SNT-6A(H)
Operation ambient temperature
Storage temperature
Topr
Tstg
40 to 85
40 to 125
°C
*1. When mounted on board
[Mounted board]
(1) Board size : 114.3 mm 76.2 mm t1.6 mm
(2) Board name : JEDEC STANDARD51-7
Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.
SOT-23-5
600
SNT-6A(H)
400
200
0
100
150
50
0
Ambient temperature (Ta) [C]
Figure 4 Power Dissipation of The Package (When Mounted on Board)
7
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
Electrical Characteristics
Table 6
(Ta = 25°C unless otherwise specified)
Test
Item
Symbol
VOUT(E)
Condition
Min.
Typ.
Max.
Unit
Circuit
VOUT(S) VOUT(S) VOUT(S)
Output voltage*1
Output current*2
VIN = VOUT(S)
VIN VOUT(S)
1.0 V, IOUT = 30 mA
1.0 V
V
1
0.99
1.01
IOUT
Vdrop
150*5
mA
V
V
V
V
3
1
1
1
1
1
0.5
0.54
0.23
0.20
0.15
0.14
0.58
0.35
0.30
0.23
0.21
1.5 V
2.0 V
2.5 V
3.0 V
3.3 V
VOUT(S)
VOUT(S)
VOUT(S)
VOUT(S)
VOUT(S)
1.9 V
2.4 V
2.9 V
3.2 V
5.5 V
Dropout voltage*3
IOUT = 100 mA
V
VOUT1
Line regulation
Load regulation
VOUT(S)
0.5 V
VIN
1.0 V, 10
1.0 V, IOUT = 30 mA,
6.5 V, IOUT = 30 mA
0.05
20
0.2
40
%/V
mV
1
1
1
VIN
VOUT
VOUT2
VIN = VOUT(S)
VIN = VOUT(S)
85°C
A
IOUT 100 mA
Ta
VOUT
VOUT
Output voltage
100
ppm/ C
temperature coefficient*4
40°C
Ta
Current consumption
during operation
Current consumption
during shutdown
Input voltage
ON / OFF pin
input voltage “H”
ON / OFF pin
input voltage “L”
ON / OFF pin
VIN = VOUT(S)
No load
VIN = VOUT(S)
No load
1.0 V, ON / OFF pin = ON,
ISS1
9
16
A
2
1.0 V, ON / OFF pin = OFF,
ISS2
VIN
0.1
0.9
6.5
A
2
4
2.0
1.5
V
VSH
VIN = VOUT(S)
VIN = VOUT(S)
1.0 V, RL = 1.0 k
V
V
VSL
ISH
ISL
1.0 V, RL = 1.0 k
0.3
0.1
0.1
4
4
4
VIN = 6.5 V, VON / OFF = 6.5 V
VIN = 6.5 V, VON / OFF = 0 V
0.1
0.1
A
input current “H”
ON / OFF pin
input current “L”
A
VIN = VOUT(S)
f = 1.0 kHz,
1.0 V,
1.5 V
3.1 V
VOUT(S)
VOUT(S)
3.0 V
5.5 V
70
dB
dB
5
Ripple rejection
RR
Vrip = 0.5 Vrms,
OUT = 30 mA
65
5
3
I
VIN = VOUT(S)
OUT = 0 V
1.0 V, ON / OFF pin = ON,
Short-circuit current
ISHORT
300
mA
V
*1. VOUT(S) : Set output voltage
VOUT(E) : Actual output voltage
Output voltage when fixing IOUT (= 30 mA) and inputting VOUT(S) 1.0 V
*2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current.
*3. Vdrop = VIN1 (VOUT3 0.98)
VOUT3 is the output voltage when VIN = VOUT(S) 1.0 V and IOUT = 100 mA.
IN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input
V
voltage.
*4. A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
VOUT
Ta
VOUT
Ta VOUT
mV/°C *1 = VOUT(S) V *2
ppm/°C *3 1000
[
]
[ ]
[ ]
*1. Change in temperature of the output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
*5. The output current can be at least this value.
Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be paid to the
power dissipation of the package when the output current is large.
This specification is guaranteed by design.
8
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
Test Circuits
1.
VIN
VOUT
VSS
A
V
ON / OFF
Set to ON
Figure 5
2.
VIN
VOUT
A
ON / OFF
VSS
Set to VIN or GND
Figure 6
3.
VIN
VOUT
VSS
A
ON / OFF
V
Set to ON
Figure 7
4.
VIN
VOUT
RL
V
ON / OFF
A
VSS
Figure 8
5.
VIN
VOUT
RL
V
ON / OFF
VSS
Set to ON
Figure 9
9
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
Standard Circuit
Input
Output
VIN
VOUT
*1
*2
ON / OFF
CIN
CL
VSS
Single GND
GND
*1. A capacitor for stabilizing the input.
*2. A ceramic capacitor of 1.0 F or more can be used.
Figure 10
Caution The above connection diagram and constant will not guarantee successful operation. Perform
thorough evaluation using the actual application to set the constant.
Condition of Application
Input capacitor (CIN): 1.0 F or more
Output capacitor (CL): 1.0 F or more
Equivalent series resistance (RESR) of output capacitor: 1.0 or less
Caution Generally a series regulator may cause oscillation, depending on the selection of external parts.
Check that no oscillation occurs with the application using the above capacitor.
Selection of Input Capacitor (CIN) and Output Capacitor (CL)
The S-1167 Series requires an output capacitor between the VOUT pin and the VSS pin for phase compensation.
Operation is stabilized by a ceramic capacitor with an output capacitance of 1.0 F or more in the entire temperature
range. When using an OS capacitor, a tantalum capacitor, or an aluminum electrolytic capacitor, the capacitance
must be 1.0 F or more, and an equivalent series resistance (RESR) must be 1.0 or less.
The value of the output overshoot or undershoot transient response varies depending on the value of the output
capacitor. The required capacitance of the input capacitor differs depending on the application.
The recommended value for an application is CIN 1.0 F, CL 1.0 F; however, when selecting the output
capacitor, perform sufficient evaluation, including evaluation of temperature characteristics, on the actual device.
10
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
Explanation of Terms
1. Low Dropout Voltage Regulator
This voltage regulator has the low dropout voltage due to its built-in low on-resistance transistor.
2. Low Equivalent Series Resistance
A capacitor whose equivalent series resistance (RESR) is low. The S-1167 Series enables use of a low equivalent
series resistance capacitor, such as a ceramic capacitor, for the output-side capacitor (CL). A capacitor whose RESR
is 1.0 or less can be used.
3. Output Voltage (VOUT
)
The accuracy of the output voltage is ensured at 1.0% under the specified conditions of fixed input voltage*1, fixed
output current, and fixed temperature.
*1. Differs depending on the product.
Caution If the above conditions change, the output voltage value may vary and exceed the accuracy range
of the output voltage. Refer to “ Electrical Characteristics” and “ Characteristics (Typical
Data)” for details.
VOUT1
V V
4. Line Regulation
OUT
IN
Indicates the dependency of the output voltage on the input voltage. That is, the values show how much the output
voltage changes due to a change in the input voltage with the output current remaining unchanged.
5. Load Regulation (VOUT2
)
Indicates the dependency of the output voltage on the output current. That is, the values show how much the output
voltage changes due to a change in the output current with the input voltage remaining unchanged.
6. Dropout Voltage (Vdrop
)
Indicates the difference between input voltage (VIN1) and the output voltage when; decreasing input voltage (VIN)
gradually until the output voltage has dropped out to the value of 98% of output voltage (VOUT3), which is at
VIN = VOUT(S) 1.0 V.
Vdrop = VIN1 (VOUT3 0.98)
11
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
VOUT
Ta V
7. Output Voltage Temperature Coefficient
OUT
The shaded area in Figure 11 is the range where VOUT varies in the operation temperature range when the output
voltage temperature coefficient is 100 ppm/C.
Example of S-1167B28 typ. product
VOUT
[V]
0.28 mV/C
*1
VOUT(E)
0.28 mV/C
40
25
85
Ta [C]
*1. VOUT(E) is the value of the output voltage measured at Ta = 25C.
Figure 11
A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
VOUT
Ta
VOUT
Ta VOUT
mV/°C *1 = VOUT(S) V *2
ppm/°C *3 1000
[ ]
[
]
[ ]
*1. Change in temperature of the output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
12
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
Operation
1. Basic Operation
Figure 12 shows the block diagram of the S-1167 Series.
The error amplifier compares the reference voltage (Vref) with feedback voltage (Vfb), which is the output voltage
resistance-divided by feedback resistors (Rs and Rf). It supplies the gate voltage necessary to maintain the constant
output voltage which is not influenced by the input voltage and temperature change, to the output transistor.
VIN
*1
Current
supply
Error
amplifier
VOUT
Vref
Rf
Vfb
Reference voltage
circuit
Rs
VSS
*1. Parasitic diode
Figure 12
2. Output Transistor
In the S-1167 Series, a low on-resistance P-channel MOS FET is used as the output transistor.
Be sure that VOUT does not exceed VIN 0.3 V to prevent the voltage regulator from being damaged due to reverse
current flowing from the VOUT pin through a parasitic diode to the VIN pin, when the potential of VOUT became higher
than VIN.
13
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
3. ON / OFF Pin
This pin starts and stops the regulator.
When the ON / OFF pin is set to OFF level, the entire internal circuit stops operating, and the built-in P-channel MOS
FET output transistor between the VIN pin and the VOUT pin is turned off, reducing current consumption significantly.
The VOUT pin becomes the VSS level due to the internally divided resistance of several M between the VOUT pin
and the VSS pin.
Note that the current consumption increases if a voltage of 0.3 V to VIN 0.3 V is applied to the ON / OFF pin.
The structure of the ON / OFF pin is as shown in Figure 13. Since the ON / OFF pin is neither pulled down nor
pulled up internally, do not use it in the floating status. When not using the ON / OFF pin, connect it to the VSS pin
in the product A type, and connect it to the VIN pin in B type.
Table 7
Product Type
ON / OFF Pin
“L”: ON
Internal Circuit
Operate
Stop
VOUT Pin Voltage
Set value
Current Consumption
A
A
B
B
ISS1
ISS2
ISS2
ISS1
“H”: OFF
“L”: OFF
“H”: ON
VSS level
Stop
VSS level
Operate
Set value
VIN
ON / OFF
VSS
Figure 13
14
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
Precautions
• Wiring patterns for the VIN pin, the VOUT pin and GND should be designed so that the impedance is low. When
mounting an output capacitor between the VOUT pin and the VSS pin (CL) and a capacitor for stabilizing the input
between the VIN pin and the VSS pin (CIN), the distance from the capacitors to these pins should be as short as
possible.
• Note that generally the output voltage may increase when a series regulator is used at low load current (10 A or less).
• Note that generally the output voltage may increase due to the leakage current from an output driver when a series
regulator is used at high temperature.
• Generally a series regulator may cause oscillation, depending on the selection of external parts. The following
conditions are recommended for the S-1167 Series. However, be sure to perform sufficient evaluation under the
actual usage conditions for selection, including evaluation of temperature characteristics.
Input capacitor (CIN): 1.0 F or more
Output capacitor (CL): 1.0 F or more
Equivalent series resistance (RESR): 1.0 or less
• The voltage regulator may oscillate when the impedance of the power supply is high and the input capacitance is small
or an input capacitor is not connected.
• It is important to sufficiently evaluate the output voltage fluctuation due to the power supply fluctuation and load
fluctuation characteristics in the actual equipment.
• Overshoot may occur in the output voltage momentarily if the voltage is rapidly raised at power-on or when the power
supply fluctuates. Sufficiently evaluate the output voltage at power-on with the actual device.
• The application conditions for the input voltage, the output voltage, and the load current should not exceed the package
power dissipation.
• Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
protection circuit.
• In determining the output current, attention should be paid to the output current value specified in Table 6 in “
Electrical Characteristics” and footnote *5 of the table.
• ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by products
including this IC of patents owned by a third party.
15
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
Characteristics (Typical Data)
1. Output Voltage vs. Output Current (When Load Current Increases) (Ta = 25°C)
S-1167B15
S-1167B30
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
V
IN=3.3 V
3.5 V
4.0 V
V
IN=1.8 V
3.5 V
5.0 V
6.5 V
6.5 V
2.5 V
2.0 V
0
100
200
300
400
500
0
100
200
300
IOUT [mA]
400
500
I
OUT [mA]
S-1167B50
6
5
4
3
2
1
0
Remark In determining the output current, attention should
be paid to the following.
V
IN=5.3 V
5.5 V
1. The minimum output current value and footnote
*5 specified of Table 6 in the “ Electrical
Characteristics”
6.0 V
6.5 V
2. The package power dissipation
0
100
200
300
400
500
I
OUT [mA]
2. Output Voltage vs. Input Voltage (Ta = 25°C)
S-1167B15
S-1167B30
1.6
3.1
1.5
3.0
1.4
2.9
1 mA
1 mA
1.3
2.8
2.7
2.6
2.5
30 mA
30 mA
100 mA
100 mA
1.2
1.1
1.0
1.0
1.5
2.0
V
2.5
3.0
3.5
2.5
3.0
3.5
4.0
4.5
5.0
IN [V]
VIN [V]
S-1167B50
5.1
5.0
4.9
4.8
4.7
4.6
4.5
1 mA
30 mA
100 mA
4.5
5.0
5.5
IN [V]
6.0
6.5
V
16
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
3. Dropout Voltage vs. Output Current
S-1167B15
S-1167B30
0.50
0.45
0.40
0.30
0.25
0.20
0.15
0.10
0.05
0
0.35
Ta = 85 C
Ta = 85 C
25 C
0.30
25 C
0.25
0.20
0.15
0.10
0.05
0
40 C
40 C
0
50
100
OUT [mA]
150
200
0
50
100
OUT [mA]
150
200
I
I
S-1167B50
0.25
0.20
0.15
0.10
0.05
0
Ta = 85 C
25 C
40 C
0
50
100
OUT [mA]
150
200
I
4. Dropout Voltage vs. Set Output Voltage
0.40
0.35
I
OUT=150 mA
0.30
0.25
0.20
0.15
0.10
0.05
0
100 mA
50 mA
30 mA
10 mA
0
1
2
3
4
5
6
V
OUT(S) [V]
17
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
5. Output Voltage vs. Ambient Temperature
S-1167B15
S-1167B30
3.20
1.60
3.15
1.55
1.50
1.45
1.40
3.10
3.05
3.00
2.95
2.90
2.85
2.80
0
15
10
35
60
85
0
15
10
35
60
85
Ta [C
]
Ta [C
]
S-1167B50
5.2
5.1
5.0
4.9
4.8
0
15
10
35
60
85
Ta [C
]
6. Current Consumption vs. Input Voltage
S-1167B15
S-1167B30
10
10
8
6
8
6
4
2
0
4
2
0
85 C
25 C
40 C
85 C
25 C
40 C
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
VIN
[
V]
VIN [V]
S-1167B50
10
8
6
4
85 C
25 C
40 C
2
0
0
1
2
3
4
5
6
7
VIN [V]
18
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
7. Ripple Rejection (Ta = 25°C)
S-1167B15
S-1167B30
VIN = 2.5 V, COUT =1.0 F
VIN = 4.0 V, COUT = 1.0 F
100
80
60
40
20
0
100
80
60
40
20
0
I
OUT = 1 mA
30 mA
I
OUT = 1 mA
30 mA
100 mA
100 mA
10
100
1K
10K 100K
1M
10
100
1K
10K 100K
1M
Frequency [Hz]
Frequency [Hz]
S-1167B50
VIN = 6.0 V, COUT =1.0 F
100
80
60
40
20
0
I
OUT = 1 mA
30 mA
100 mA
10
100
1K
10K 100K
1M
Frequency [Hz]
19
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
Reference Data
1. Input Transient Response Characteristics (Ta = 25°C)
S-1167B15
S-1167B30
IOUT = 30 mA, tr = tf = 5.0 s, COUT = 1.0 F, CIN = 1.0 F
IOUT = 30 mA, tr = tf = 5.0 s, COUT =1.0 F, CIN = 1.0 F
1.62
1.60
1.58
1.56
1.54
1.52
1.50
1.48
1.46
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
3.06
3.04
3.02
3.00
2.98
2.96
2.94
6
5
4
3
2
1
0
V
IN
V
IN
V
OUT
V
OUT
40
20 0 20 40 60 80 100120140 160
t [s]
40
20 0 20 40 60 80 100120140 160
t [s]
S-1167B50
OUT = 30 mA, tr = tf = 5.0 s, COUT =1.0 F, CIN = 1.0 F
I
5.10
5.08
5.06
5.04
5.02
5.00
4.98
4.96
4.94
8
7
6
5
4
3
2
1
0
V
IN
V
OUT
40
20 0 20 40 60 80 100120140 160
t [s]
2. Load Transient Response Characteristics (Ta = 25°C)
S-1167B15
S-1167B30
VIN = 2.5 V, COUT = 1.0
F, CIN = 1.0
F, IOUT = 50 mA
100 mA
VIN = 4.0 V, COUT = 1.0
F, CIN = 1.0
F, IOUT = 50 mA
100 mA
1.70
150
3.15
150
1.65
100
50
0
3.10
100
50
0
I
OUT
I
OUT
1.60
1.55
1.50
1.45
1.40
3.05
3.00
2.95
2.90
2.85
V
OUT
V
OUT
50
50
100
150
100
150
40
20 0 20 40 60 80 100120140 160
40
20 0 20 40 60 80 100120140 160
t [s]
t [s]
S-1167B50
VIN =6.0 V, COUT = 1.0
F, CIN = 1.0
F, IOUT = 50 mA
100 mA
5.15
150
5.10
100
50
0
I
OUT
5.05
5.00
4.95
4.90
4.85
V
OUT
50
100
150
40
20 0 20 40 60 80 100120140 160
t [s]
20
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
3. ON / OFF Pin Transient Response Characteristics (Ta = 25°C)
S-1167B15
S-1167B30
VIN = 4.0 V, COUT =1.0 F, CIN = 1.0 F, IOUT = 100 mA
VIN = 2.5 V, COUT =1.0 F, CIN = 1.0 F, IOUT = 100 mA
5
4
3
2
1
0
1
3
2
1
0
10
6
4
2
0
8
6
V
ON / OFF
V
ON / OFF
4
1
2
2
V
OUT
V
OUT
2
3
0
4
6
2
0.4
0.2
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
0.4
0.2
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
t [ms]
t [ms]
S-1167B50
IN = 6.0 V, COUT =1.0 F, CIN = 1.0 F, IOUT = 100 mA
V
20
16
12
8
9
6
3
0
VON / OFF
4
3
VOUT
0
6
9
4
0.4
0.2
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
t [ms]
21
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1167 Series
Rev.3.2_02
Marking Specifications
1. SOT-23-5
Top view
(1) to (3):
Product code (refer to Product name vs. Product code)
Lot number
5
4
(4)
:
(1) (2) (3) (4)
1
2
3
Product name vs. Product code
1. 1 S-1167 Series A type
Product code
Product name
(1)
(2)
2
3
2
2
2
2
3
(3)
A
P
E
P
S
V
J
S-1167A15-M5T1x
S-1167A1J-M5T1x
S-1167A19-M5T1x
S-1167A30-M5T1x
S-1167A33-M5T1x
S-1167A36-M5T1x
S-1167A50-M5T1x
P
P
P
P
P
P
P
1. 2 S-1167 Series B type
Product code
Product code
Product name
Product name
(1)
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
(2)
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
(3)
A
B
C
D
E
F
G
H
I
(1)
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
(2)
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
(3)
V
W
X
Y
Z
A
B
C
D
E
F
G
H
I
J
K
L
S-1167B15-M5T1x
S-1167B16-M5T1x
S-1167B17-M5T1x
S-1167B18-M5T1x
S-1167B19-M5T1x
S-1167B20-M5T1x
S-1167B21-M5T1x
S-1167B22-M5T1x
S-1167B23-M5T1x
S-1167B24-M5T1x
S-1167B25-M5T1x
S-1167B26-M5T1x
S-1167B27-M5T1x
S-1167B28-M5T1x
S-1167B29-M5T1x
S-1167B30-M5T1x
S-1167B31-M5T1x
S-1167B32-M5T1x
S-1167B33-M5T1x
S-1167B34-M5T1x
S-1167B35-M5T1x
S-1167B36-M5T1x
S-1167B37-M5T1x
S-1167B38-M5T1x
S-1167B39-M5T1x
S-1167B40-M5T1x
S-1167B41-M5T1x
S-1167B42-M5T1x
S-1167B43-M5T1x
S-1167B44-M5T1x
S-1167B45-M5T1x
S-1167B46-M5T1x
S-1167B47-M5T1x
S-1167B48-M5T1x
S-1167B49-M5T1x
S-1167B50-M5T1x
S-1167B51-M5T1x
S-1167B52-M5T1x
S-1167B53-M5T1x
S-1167B54-M5T1x
S-1167B55-M5T1x
J
K
L
M
N
O
P
Q
R
S
T
M
N
O
U
Remark 1. x: G or U
2. Please select products of environmental code = U for Sn 100%, halogen-free products.
22
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.3.2_02
S-1167 Series
2. SNT-6A(H)
Top view
5
(1) to (3):
Product code (refer to Product name vs. Product code)
Lot number
6
4
(4) to (6):
(1) (2) (3)
(4) (5) (6)
1
2
3
Product name vs. Product code
Product code
Product code
Product name
Product name
(1)
(2)
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
(3)
A
B
C
D
E
F
G
H
I
(1)
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
(2)
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
(3)
V
W
X
Y
Z
A
B
C
D
E
F
G
H
I
J
K
L
S-1167B15-I6T2U
S-1167B16-I6T2U
S-1167B17-I6T2U
S-1167B18-I6T2U
S-1167B19-I6T2U
S-1167B20-I6T2U
S-1167B21-I6T2U
S-1167B22-I6T2U
S-1167B23-I6T2U
S-1167B24-I6T2U
S-1167B25-I6T2U
S-1167B26-I6T2U
S-1167B27-I6T2U
S-1167B28-I6T2U
S-1167B29-I6T2U
S-1167B30-I6T2U
S-1167B31-I6T2U
S-1167B32-I6T2U
S-1167B33-I6T2U
S-1167B34-I6T2U
S-1167B35-I6T2U
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
S-1167B36-I6T2U
S-1167B37-I6T2U
S-1167B38-I6T2U
S-1167B39-I6T2U
S-1167B40-I6T2U
S-1167B41-I6T2U
S-1167B42-I6T2U
S-1167B43-I6T2U
S-1167B44-I6T2U
S-1167B45-I6T2U
S-1167B46-I6T2U
S-1167B47-I6T2U
S-1167B48-I6T2U
S-1167B49-I6T2U
S-1167B50-I6T2U
S-1167B51-I6T2U
S-1167B52-I6T2U
S-1167B53-I6T2U
S-1167B54-I6T2U
S-1167B55-I6T2U
J
K
L
M
N
O
P
Q
R
S
T
M
N
O
U
23
2.9±0.2
1.9±0.2
4
5
+0.1
-0.06
1
2
3
0.16
0.95±0.1
0.4±0.1
No. MP005-A-P-SD-1.3
TITLE
SOT235-A-PKG Dimensions
MP005-A-P-SD-1.3
No.
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.1(10 pitches:40.0±0.2)
+0.1
-0
2.0±0.05
0.25±0.1
ø1.5
+0.2
-0
4.0±0.1
ø1.0
1.4±0.2
3.2±0.2
3
4
2 1
5
Feed direction
No. MP005-A-C-SD-2.1
TITLE
SOT235-A-Carrier Tape
MP005-A-C-SD-2.1
No.
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. MP005-A-R-SD-1.1
TITLE
SOT235-A-Reel
MP005-A-R-SD-1.1
No.
ANGLE
UNIT
QTY.
3,000
mm
ABLIC Inc.
1.57±0.03
6
4
5
+0.05
-0.02
0.08
1
2
3
0.5
0.48±0.02
0.2±0.05
No. PI006-A-P-SD-2.1
SNT-6A(H)-A-PKG Dimensions
PI006-A-P-SD-2.1
TITLE
No.
ANGLE
UNIT
mm
ABLIC Inc.
+0.1
-0
ø1.5
4.0±0.1
2.0±0.05
0.25±0.05
+0.1
ø0.5
-0
4.0±0.1
0.65±0.05
1.85±0.05
3
2
5
1
6
4
Feed direction
No. PI006-A-C-SD-2.0
TITLE
SNT-6A(H)-A-Carrier Tape
PI006-A-C-SD-2.0
No.
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. PI006-A-R-SD-1.0
TITLE
SNT-6A(H)-A-Reel
PI006-A-R-SD-1.0
No.
ANGLE
UNIT
QTY.
5,000
mm
ABLIC Inc.
0.52
2
1.36
0.52
1
0.3
0.2
1.
2.
(0.25 mm min. / 0.30 mm typ.)
(1.30 mm ~ 1.40 mm)
1.
2.
0.03 mm
3.
4.
SNT
1. Pay attention to the land pattern width (0.25 mm min. / 0.30 mm typ.).
2. Do not widen the land pattern to the center of the package (1.30 mm to 1.40 mm).
Caution 1. Do not do silkscreen printing and solder printing under the mold resin of the package.
2. The thickness of the solder resist on the wire pattern under the package should be 0.03 mm
or less from the land pattern surface.
3. Match the mask aperture size and aperture position with the land pattern.
4. Refer to "SNT Package User's Guide" for details.
(0.25 mm min. / 0.30 mm typ.)
(1.30 mm ~ 1.40 mm)
1.
2.
SNT-6A(H)-A
-Land Recommendation
TITLE
No. PI006-A-L-SD-4.1
No.
PI006-A-L-SD-4.1
ANGLE
UNIT
mm
ABLIC Inc.
Disclaimers (Handling Precautions)
1. All the information described herein (product data, specifications, figures, tables, programs, algorithms and application
circuit examples, etc.) is current as of publishing date of this document and is subject to change without notice.
2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not responsible for damages caused by the reasons other than the products described herein
(hereinafter "the products") or infringement of third-party intellectual property right and any other right due to the use
of the information described herein.
3. ABLIC Inc. is not responsible for damages caused by the incorrect information described herein.
4. Be careful to use the products within their specified ranges. Pay special attention to the absolute maximum ratings,
operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not responsible for damages caused by failures and / or accidents, etc. that occur due to the use of the
products outside their specified ranges.
5. When using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6. When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7. The products must not be used or provided (exported) for the purposes of the development of weapons of mass
destruction or military use. ABLIC Inc. is not responsible for any provision (export) to those whose purpose is to
develop, manufacture, use or store nuclear, biological or chemical weapons, missiles, or other military use.
8. The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses. Do
not apply the products to the above listed devices and equipments without prior written permission by ABLIC Inc.
Especially, the products cannot be used for life support devices, devices implanted in the human body and devices
that directly affect human life, etc.
Prior consultation with our sales office is required when considering the above uses.
ABLIC Inc. is not responsible for damages caused by unauthorized or unspecified use of our products.
9. Semiconductor products may fail or malfunction with some probability.
The user of the products should therefore take responsibility to give thorough consideration to safety design including
redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing injury or
death, fires and social damage, etc. that may ensue from the products' failure or malfunction.
The entire system must be sufficiently evaluated and applied on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc.
The information described herein does not convey any license under any intellectual property rights or any other
rights belonging to ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any
part of this document described herein for the purpose of disclosing it to a third-party without the express permission
of ABLIC Inc. is strictly prohibited.
14. For more details on the information described herein, contact our sales office.
2.2-2018.06
www.ablic.com
相关型号:
S-1167B41-I6T2G
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
SII
S-1167B41-I6T2U
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
ABLIC
S-1167B41-M5T1G
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
SII
S-1167B41-M5T1X
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
ABLIC
S-1167B42-I6T2G
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
SII
S-1167B42-I6T2U
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
ABLIC
S-1167B42-M5T1G
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
SII
S-1167B42-M5T1X
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
ABLIC
S-1167B43-I6T2G
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
SII
S-1167B43-I6T2U
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
ABLIC
S-1167B43-M5T1G
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
SII
S-1167B43-M5T1X
ULTRA LOW CURRENT CONSUMPTION, HIGH RIPPLE REJECTION AND LOW DROPOUT CMOS VOLTAGE REGULATOR
ABLIC
©2020 ICPDF网 联系我们和版权申明