S-1165B39MC-N6YTFX [ABLIC]
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR;型号: | S-1165B39MC-N6YTFX |
厂家: | ABLIC |
描述: | HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR |
文件: | 总23页 (文件大小:385K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
S-1165 Series
HIGH RIPPLE-REJECTION LOW DROPOUT
CMOS VOLTAGE REGULATOR
www.ablic.com
© ABLIC Inc., 2002-2015
Rev.4.1_02
The S-1165 Series is a positive voltage regulator with a low dropout voltage, high-accuracy output voltage, and
low current consumption developed based on CMOS technology.
A built-in low on-resistance transistor provides a low dropout voltage and large output current, and a built-in
overcurrent protection circuit prevents the load current from exceeding the current capacity of the output
transistor. An ON/OFF circuit ensures a long battery life, and a small SOT-23-5 package realizes high-density
mounting.
Features
1.5 V to 5.5 V, selectable in 0.1 V step
1.0%
140 mV typ. (3.0 V output product, IOUT = 200 mA)
During operation: 35 A typ., 65 A max.
During power-off: 0.1 A typ., 1.0 A max.
Possible to output 200 mA (VIN VOUT(S) 1.0 V)*1
70 dB typ. (f = 1.0 kHz)
Output voltage:
Output voltage accuracy:
Dropout voltage:
Current consumption:
Output current:
Ripple rejection:
Limits overcurrent of output transistor.
Ensures long battery life.
Built-in overcurrent protection circuit:
Built-in ON/OFF circuit:
Operation temperature range:
Ta = 40°C to 85°C
Lead-free, Sn 100%, halogen-free*2
*1. Attention should be paid to the power dissipation of the package when the output current is large.
*2. Refer to “ Product Name Structure” for details.
Applications
Constant-voltage power supply for battery-powered device
Constant-voltage power supply for personal communication device
Constant-voltage power supply for home electric appliance
Constant-voltage power supply for cellular phone
Package
SOT-23-5
1
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Block Diagram
*1
VIN
VOUT
Overcurrent
protection circuit
ON/OFF
circuit
ON/OFF
Reference
voltage circuit
VSS
*1. Parasitic diode
Figure 1
2
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Product Name Structure
Users can select the product type, output voltage for the S-1165 Series. Refer to “1.
Product name”
regarding the contents of product name, “2. Package” regarding the package drawings and “3.
Product name list” regarding details of the product name.
1. Product name
S-1165
x
xx MC
-
xxx TF
x
Environmental code
U: Lead-free (Sn 100%), halogen-free
G: Lead-free (for details, please contact our sales office)
IC direction in tape specifications*1
Product name (abbreviation)*2
Package name (abbreviation)
MC: SOT-23-5
Output voltage
15 to 55
(e.g., when the output voltage is 1.5 V, it is expressed
as 15.)
Product type*3
A: ON/OFF pin negative logic
B: ON/OFF pin positive logic
1. Refer to the tape drawing.
2. Refer to the “Product name list”.
3. Refer to “3. ON/OFF pin” in “ Operation”.
2. Package
Drawing Code
Tape
MP005-A-C-SD
Package Name
SOT-23-5
Package
MP005-A-P-SD
Reel
MP005-A-R-SD
3
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
3. Product name list
Table 1
Output Voltage
1.5V±1.0%
1.6V±1.0%
1.7V±1.0%
1.8V±1.0%
1.9V±1.0%
2.0V±1.0%
2.1V±1.0%
2.2V±1.0%
2.3V±1.0%
2.4V±1.0%
2.5V±1.0%
2.6V±1.0%
2.7V±1.0%
2.8V±1.0%
2.9V±1.0%
3.0V±1.0%
3.1V±1.0%
3.2V±1.0%
3.3V±1.0%
3.4V±1.0%
3.5V±1.0%
3.6V±1.0%
3.7V±1.0%
3.8V±1.0%
3.9V±1.0%
4.0V±1.0%
4.1V±1.0%
4.2V±1.0%
4.3V±1.0%
4.4V±1.0%
4.5V±1.0%
4.6V±1.0%
4.7V±1.0%
4.8V±1.0%
4.9V±1.0%
5.0V±1.0%
5.1V±1.0%
5.2V±1.0%
5.3V±1.0%
5.4V±1.0%
5.5V±1.0%
Product Name
S-1165B15MC-N6ATFx
S-1165B16MC-N6BTFx
S-1165B17MC-N6CTFx
S-1165B18MC-N6DTFx
S-1165B19MC-N6ETFx
S-1165B20MC-N6FTFx
S-1165B21MC-N6GTFx
S-1165B22MC-N6HTFx
S-1165B23MC-N6ITFx
S-1165B24MC-N6JTFx
S-1165B25MC-N6KTFx
S-1165B26MC-N6LTFx
S-1165B27MC-N6MTFx
S-1165B28MC-N6NTFx
S-1165B29MC-N6OTFx
S-1165B30MC-N6PTFx
S-1165B31MC-N6QTFx
S-1165B32MC-N6RTFx
S-1165B33MC-N6STFx
S-1165B34MC-N6TTFx
S-1165B35MC-N6UTFx
S-1165B36MC-N6VTFx
S-1165B37MC-N6WTFx
S-1165B38MC-N6XTFx
S-1165B39MC-N6YTFx
S-1165B40MC-N6ZTFx
S-1165B41MC-N7ATFx
S-1165B42MC-N7BTFx
S-1165B43MC-N7CTFx
S-1165B44MC-N7DTFx
S-1165B45MC-N7ETFx
S-1165B46MC-N7FTFx
S-1165B47MC-N7GTFx
S-1165B48MC-N7HTFx
S-1165B49MC-N7ITFx
S-1165B50MC-N7JTFx
S-1165B51MC-N7KTFx
S-1165B52MC-N7LTFx
S-1165B53MC-N7MTFx
S-1165B54MC-N7NTFx
S-1165B55MC-N7OTFx
Remark 1. Please contact our sales office for type A products.
2. x: G or U
3. Please select products of environmental code = U for Sn 100%,
halogen-free products.
4
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Pin Configuration
SOT-23-5
Top view
Table 2
Pin No.
Symbol
VIN
VSS
Description
Input voltage pin
GND pin
ON/OFF pin
No connection
Output voltage pin
5
4
1
2
3
4
5
ON/OFF
NC*1
VOUT
*1. The NC pin is electrically open.
The NC pin can be connected to VIN pin or VSS pin.
1
2
3
Figure
2
5
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Absolute Maximum Ratings
Table 3
(Ta 25C unless otherwise specified)
Item
Symbol
VIN
VON/OFF
VOUT
PD
Absolute Maximum Rating
Unit
V
Input voltage
VSS 0.3 to VSS 7
VSS 0.3 to VIN 0.3
VSS 0.3 to VIN 0.3
300 (When not mounted on board)
600*1
Output voltage
Power dissipation
mW
mW
C
Operation ambient temperature
Storage temperature
Topr
Tstg
40 to 85
40 to 125
*1. When mounted on board
[Mounted on board]
(1) Board size : 114.3 mm 76.2 mm t1.6 mm
(2) Board name : JEDEC STANDARD51-7
Caution The absolute maximum ratings are rated values exceeding which the product could suffer
physical damage. These values must therefore not be exceeded under any conditions.
700
600
500
400
300
200
100
0
100
Ambient Temperature (Ta) [C]
Figure 3 Power Dissipation of Package (When Mounted on Board)
150
50
0
6
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Electrical Characteristics
Table 4
(Ta 25C unless otherwise specified)
Test
Circuit
Item
Symbol
VOUT(E)
Conditions
Min.
Typ.
Max.
Unit
VOUT(S) VOUT(S) VOUT(S)
Output voltage*1
VIN VOUT(S) 1.0 V, IOUT 30 mA
VIN VOUT(S) 1.0 V
V
1
0.99
200*5
1.01
0.30
0.20
Output current*2
Dropout voltage*3
IOUT
0.20
0.14
mA
V
3
1
Vdrop
IOUT 200 mA
1.5 V VOUT(S) 2.5 V
2.6 V VOUT(S) 5.5 V
VOUT1
VINVOUT
VOUT(S) 0.5 V VIN 6.5 V,
IOUT 30 mA
VIN VOUT(S) 1.0 V,
1.0 mA IOUT 200 mA
VIN VOUT(S) 1.0 V, IOUT 30 mA,
40C Ta 85C
Line regulation
Load regulation
0.05
20
0.2
40
%/V
mV
VOUT2
VOUT
TaVOUT
Output voltage
ppm/
C
100
35
temperature coefficient*4
Current consumption
during operation
Current consumption
during power-off
Input voltage
VIN VOUT(S) 1.0 V, ON/OFF pin ON,
no load
ISS1
65
A
2
VIN VOUT(S) 1.0 V, ON/OFF pin OFF,
no load
ISS2
VIN
0.1
1.0
6.5
2.0
1.5
V
ON/OFF pin
input voltage “H”
ON/OFF pin
input voltage “L”
ON/OFF pin
input current “H”
ON/OFF pin
VSH
VIN VOUT(S) 1.0 V, RL 1.0 k
VIN VOUT(S) 1.0 V, RL 1.0 k
VIN 6.5 V, VON/OFF 6.5 V
VIN 6.5 V, VON/OFF = 0 V
4
VSL
ISH
0.1
0.1
0.3
0.1
0.1
A
ISL
input current “L”
VIN VOUT(S) 1.0 V, f 1.0 kHz,
Vrip 0.5 Vrms, IOUT 30 mA
VIN VOUT(S) 1.0 V, ON/OFF pin ON,
VOUT 0 V
RR
Ripple rejection
70
dB
5
3
Short-circuit current
Ishort
350
mA
*1. VOUT(S): Set output voltage
VOUT(E): Actual output voltage
Output voltage when fixing IOUT( 30 mA) and inputting VOUT(S) 1.0 V
*2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output
current.
*3. Vdrop VIN1 (VOUT3 0.98)
VOUT3 is the output voltage when VIN VOUT(S) 1.0 V and IOUT 200 mA.
VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing
the input voltage.
*4. A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
VOUT
Ta
VOUT
Ta VOUT
mV/°C *1 = VOUT(S)
V
[ ]
*2
ppm/°C *3 1000
[
]
[ ]
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
*5. The output current can be at least this value.
Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be
paid to the power dissipation of the package when the output current is large.
This specification is guaranteed by design.
7
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Test Circuits
1.
+
A
VIN
VOUT
VSS
+
V
ON/OFF
Set to ON
Figure 4
2.
A
VIN
VOUT
VSS
ON/OFF
Set to
VIN or GND
Figure 5
3.
VIN
VOUT
VSS
A
V
ON/OFF
Set to ON
Figure 6
4.
VOUT
VSS
VIN
A
RL
V
ON/OFF
Figure 7
5.
VIN
VOUT
VSS
V
ON/OFF
RL
Set to ON
Figure 8
8
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Standard Circuit
Output
Input
VIN
VOUT
*2
*1
ON/OFF
CL
CIN
VSS
GND
Single GND
*1. CIN is a capacitor for stabilizing the input.
*2. A tantalum capacitor (2.2 F or more) can be used.
Figure 9
Caution The above connection diagram and constant will not guarantee successful operation.
Perform thorough evaluation using the actual application to set the constant.
Condition of Application
Input capacitor (CIN):
1.0 F or more
Output capacitor (CL): 2.2 F or more (tantalum capacitor)
Caution Generally a series regulator may cause oscillation, depending on the selection of external
parts. Check that no oscillation occurs with the application using the above capacitor.
9
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Explanation of Terms
1. Low dropout voltage regulator
This voltage regulator has the low dropout voltage due to its built-in low on-resistance transistor.
2. Output voltage (VOUT
)
The accuracy of the output voltage is ensured at 1.0% under the specified conditions of fixed input
voltage*1, fixed output current, and fixed temperature.
*1. Differs depending the product.
Caution If the above conditions change, the output voltage value may vary and exceed the
accuracy range of the output voltage. Refer to " Electrical Characteristics" and "
Characteristics (Typical Data)" for details.
VOUT1
3. Line regulation
V V
OUT
IN
Indicates the dependency of the output voltage on the input voltage. That is, the value shows how
much the output voltage changes due to a change in the input voltage with the output current remaining
unchanged.
4. Load regulation (VOUT2
)
Indicates the dependency of the output voltage on the output current. That is, the value shows how
much the output voltage changes due to a change in the output current with the input voltage remaining
unchanged.
5. Dropout voltage (Vdrop
)
Indicates the difference between input voltage (VIN1) and the output voltage when; decreasing input
voltage (VIN) gradually until the output voltage has dropped out to the value of 98% of output voltage
(VOUT3), which is at VIN = VOUT(S) 1.0 V.
Vdrop VIN1 (VOUT3 0.98)
10
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
VOUT
6. Output voltage temperature coefficient
Ta V
OUT
The shaded area in Figure 10 is the range where VOUT varies in the operation temperature range when
the output voltage temperature coefficient is 100 ppm/C.
Example of S-1165B28 typ. product
VOUT
[V]
0.28 mV/C
*1
VOUT(E)
0.28 mV/C
40
25
85
Ta [C]
*1. VOUT(E) is the value of the output voltage measured at Ta = 25C.
Figure 10
A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
VOUT
Ta
VOUT
Ta VOUT
mV/°C *1 = VOUT(S)
V
[ ]
*2
ppm/°C *3 1000
[ ]
[
]
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
11
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Operation
1. Basic operation
Figure 11 shows the block diagram of the S-1165 Series.
The error amplifier compares the reference voltage (Vref) with feedback voltage (Vfb), which is the output
voltage resistance-divided by feedback resistors (Rs and Rf). It supplies the gate voltage necessary to
maintain the constant output voltage which is not influenced by the input voltage and temperature
change, to the output transistor.
VIN
*1
Current
supply
Error
VOUT
amplifier
Vref
Rf
Vfb
Reference voltage
circuit
Rs
VSS
*1. Parasitic diode
Figure 11
2. Output transistor
In the S-1165 Series, a low on-resistance P-channel MOS FET is used as the output transistor.
Be sure that VOUT does not exceed VIN 0.3 V to prevent the voltage regulator from being damaged due
to reverse current flowing from the VOUT pin through a parasitic diode to the VIN pin, when the potential
of VOUT became higher than VIN.
12
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
3. ON/OFF pin
This pin starts and stops the regulator.
When the ON/OFF pin is set to OFF level, the entire internal circuit stops operating, and the built-in P-
channel MOS FET output transistor between the VIN pin and the VOUT pin is turned off, reducing current
consumption significantly. The VOUT pin becomes the Vss level due to the internally divided resistance
of several hundreds k between the VOUT pin and the VSS pin.
The structure of the ON/OFF pin is as shown in Figure 12. Since the ON/OFF pin is neither pulled
down nor pulled up internally, do not use it in the floating status. In addition, note that the current
consumption increases if a voltage of 0.3 V to VIN – 0.3 V is applied to the ON/OFF pin. When not using
the ON/OFF pin, connect it to the VSS pin in the product A type, connect it to the VIN pin in B type.
Table 5
Product Type
ON/OFF Pin
“L”: ON
“H”: OFF
“L”: OFF
“H”: ON
Internal Circuit
Operate
Stop
VOUT Pin Voltage
Set value
Current Consumption
A
A
B
B
ISS1
ISS2
ISS2
ISS1
VSS level
VSS level
Set value
Stop
Operate
VIN
ON/OFF
VSS
Figure 12
Selection of Output Capacitor (CL)
The S-1165 Series performs phase compensation using the internal phase compensator in the IC and the
ESR (Equivalent Series Resistance) of the output capacitor to enable stable operation independent of
changes in the output load. Therefore, always place a capacitor (CL) of 2.2 F or more between the
VOUT pin and the VSS pin.
For stable operation of the S-1165 Series, it is essential to employ a capacitor whose ESR is within an
optimum range. Using a capacitor whose ESR is outside the optimum range (approximately 0.5 to
5 ), whether larger or smaller, may cause an unstable output, resulting in oscillation. For this reason, a
tantalum electrolytic capacitor is recommended.
When a ceramic capacitor or an OS capacitor with a low ESR is used, it is necessary to connect an
additional resistor that serves as the ESR in series with the output capacitor. The required resistance
value is approximately 0.5 to 5 , which varies depending on the usage conditions, so perform sufficient
evaluation for selection. Ordinarily, around 1.0 is recommended.
Note that an aluminum electrolytic capacitor may increase the ESR at a low temperature, causing
oscillation. When using this kind of capacitor, perform thorough evaluation, including evaluation of
temperature characteristics.
13
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Precautions
Wiring patterns for the VIN pin, the VOUT pin and GND should be designed so that the impedance is
low. When mounting an output capacitor between the VOUT pin and the VSS pin (CL) and a capacitor
for stabilizing the input between the VIN pin and the VSS pin (CIN), the distance from the capacitors to
these pins should be as short as possible.
Note that generally the output voltage may increase when a series regulator is used at low load current
(1.0 mA or less).
The S-1165 Series performs phase compensation by using an internal phase compensator and the ESR
of an output capacitor. Therefore, always place a capacitor of 2.2 F or more between VOUT and VSS
pins. A tantalum type capacitor is recommended. Moreover, to secure stable operation of the S-1165
Series, it is necessary to employ a capacitor with an ESR within an optimum range (0.5 to 5 ).
Using a capacitor whose ESR is outside the optimum range (approximately 0.5 to 5 ), whether larger
or smaller, may cause an unstable output, resulting in oscillation. Perform sufficient evaluation under
the actual usage conditions for selection, including evaluation of temperature characteristics.
The voltage regulator may oscillate when the impedance of the power supply is high and the input
capacitance is small or an input capacitor is not connected.
Overshoot may occur in the output voltage momentarily if the voltage is rapidly raised at power-on or
when the power supply fluctuates. Sufficiently evaluate the output voltage at power-on with the actual
device.
The application conditions for the input voltage, the output voltage, and the load current should not
exceed the package power dissipation.
Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in
electrostatic protection circuit.
In determining the output current, attention should be paid to the output current value specified in Table
4 in “ Electrical Characteristics” and footnote *5 of the table.
ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement
by products including this IC of patents owned by a third party.
14
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Characteristics (Typical Data)
(1) Output voltage vs. Output current (when load current increases)
S-1165B15 (Ta 25°C)
S-1165B30 (Ta 25°C)
2.5
4
3.5
3
2
2.5
2
VIN = 3.3 V
6.0 V
1.5
2.5 V
VIN 1.8 V
4.0 V
1
1.5
1
6.0 V
0.5
0.5
0
0
0
200
400
600
800
0
200
400
600
800
IOUT [mA]
IOUT [mA]
S-1165B50 (Ta 25°C)
6
5
4
3
2
1
0
Remark In determining the output current, attention
should be paid to the following.
6.0 V
1) The minimum output current value and
footnote *5 of Table 4 in the “ Electrical
Characteristics”
V
IN 5.3 V
2) The package power dissipation
0
200
400
600
800
IOUT [mA]
(2) Output voltage vs. Input voltage
S-1165B15 (Ta 25°C)
S-1165B30 (Ta 25°C)
1.6
3.05
3
1.55
IOUT = 1mA
30 mA
2.95
2.9
IOUT = 1mA
1.5
50 mA
30 mA
50 mA
1.5
1.45
2.85
2.8
1.4
1
2
2.5
2.5
3
3.5
4
VIN [V]
VIN [V]
S-1165B50 (Ta 25°C)
5.1
5.08
5.06
5.04
5.02
5
IOUT = 1mA
4.98
50 mA
4.96
4.94
4.92
30 mA
5.5
4.5
5
6
VIN [V]
15
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
(3) Dropout voltage vs. Output current
S-1165B15
S-1165B30
0.35
0.3
0.2
0.18
0.16
0.14
0.12
0.1
25°C
85°C
25C
0.25
0.2
85C
0.15
0.1
0.08
0.06
0.04
0.02
0
40°C
40C
0.05
0
0
0
50
100
150
200
250
50
100
150
200
250
IOUT [mA]
IOUT [mA]
S-1165B50
0.16
0.14
0.12
0.1
25C
85C
0.08
0.06
0.04
0.02
40C
0
0
50
100
150
200
250
IOUT [mA]
(4) Dropout voltage vs. Set output voltage
300
200 mA
250
200
120 mA
150
50 mA
100
30 mA
50
10 mA
0
0
1
2
3
4
5
6
7
VOUT(S) [V]
16
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
(5) Output voltage vs. Ambient temperature
S-1165B15
S-1165B30
3.1
1.6
3.05
3
1.55
1.5
2.95
2.9
1.45
1.4
-
-
20
40
0
20
40
60
80
100
-40
-20
0
20
40
60
80
100
Ta [C]
Ta [C]
S-1165B50
5.1
5.08
5.06
5.04
5.02
5
4.98
4.96
4.94
4.92
4.9
-40 -20
0
20 40 60 80 100
Ta [C]
(6) Current consumption vs. Input voltage
S-1165B15
S-1165B30
40
35
40
35
25C
25°C
30
30
25
20
15
10
5
25
20
15
10
5
85C
85°C
40°C
40C
0
0
0
2
4
6
8
0
2
4
6
8
VIN [V]
VIN [V]
S-1165B50
40
35
30
25
20
15
25C
40C
85C
10
5
0
0
2
4
6
8
VIN [V]
17
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
(7) Ripple rejection
S-1165B15 (Ta 25°C)
VIN 2.5 V, COUT 2.2 F
S-1165B30 (Ta 25°C)
VIN 4.0 V, COUT 2.2 F
100
80
100
80
IOUT = 1 mA
IOUT = 1 mA
60
40
20
0
60
40
20
0
30 mA
50 mA
30 mA
50 mA
100 k
10
100
1 k
10 k
100 k
1 M
10
100
1 k
10 k
1 M
Frequency [Hz]
Frequency [Hz]
S-1165B50 (Ta 25°C)
VIN 6.0 V, COUT 2.2 F
100
80
IOUT = 1 mA
60
40
20
0
30 mA
50 mA
100 k
10
100
1 k
10 k
1 M
Frequency [Hz]
18
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
S-1165 Series
Rev.4.1_02
Reference Data
(1) Input transient response characteristics
IOUT 30 mA, tr = tf 5.0 s, COUT 2.2 F, CIN 0 F
IOUT 30 mA, tr = tf 5.0 s, COUT 4.7 F, CIN 0 F
3.1
6
5
3.1
6
5
3.08
3.08
3.06
3.04
3.02
3
4
3
2
1
0
3.06
4
3
2
1
0
VIN
VIN
VOUT
VOUT
3.04
3.02
3
2.98
2.98
-10
0
10 20 30 40 50 60 70 80 90
-10
0
10 20 30 40 50 60 70 80 90
t [s]
t [s]
(2) Load transient response characteristics
VIN 4.0 V, COUT 2.2 F, CIN 1.0 F,
IOUT 50 mA 100 mA
VIN 4.0 V, COUT 4.7 F, CIN 1.0 F,
IOUT 50 mA 100 mA
3.4
3.3
150
100
3.4
3.3
150
100
3.2
3.1
3
50
0
3.2
3.1
3
50
0
IOUT
IOUT
-50
-50
VOUT
VOUT
2.9
2.8
-100
-150
2.9
2.8
-100
-150
-2
0
2
4
6
8
10 12 14 16 18
-2
0
2
4
6
8
10 12 14 16 18
t [s]
t [s]
(3) ON/OFF pin transient response characteristics
S-1165B15 (Ta 25°C)
VIN 2.5 V, COUT 2.2 F, CIN 1.0 F
S-1165B30 (Ta 25°C)
VIN 4.0 V, COUT 2.2 F, CIN 1.0 F
2.5
2
3
2
5
6
4
VON/OFF
4
VON/OFF
1.5
1
1
0
3
2
0
VOUT
2
VOUT
0.5
0
-1
-2
-3
1
-2
-4
-6
0
-0.5
-1
-10
0
10 20 30 40 50 60 70 80 90
-10
0
10 20 30 40 50 60 70 80 90
t [s]
t [s]
S-1165B50 (Ta 25°C)
VIN 6.0 V, COUT 2.2 F, CIN 1.0 F
7
8
6
5
VON/OFF
6
4
4
2
VOUT
3
0
2
-2
-4
-6
-8
1
0
-10
0
10 20 30 40 50 60 70 80 90
-1
t [s]
19
2.9±0.2
1.9±0.2
4
5
+0.1
-0.06
1
2
3
0.16
0.95±0.1
0.4±0.1
No. MP005-A-P-SD-1.3
TITLE
SOT235-A-PKG Dimensions
MP005-A-P-SD-1.3
No.
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.1(10 pitches:40.0±0.2)
+0.1
-0
2.0±0.05
0.25±0.1
ø1.5
+0.2
-0
4.0±0.1
ø1.0
1.4±0.2
3.2±0.2
3
4
2 1
5
Feed direction
No. MP005-A-C-SD-2.1
TITLE
SOT235-A-Carrier Tape
MP005-A-C-SD-2.1
No.
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. MP005-A-R-SD-1.1
TITLE
SOT235-A-Reel
MP005-A-R-SD-1.1
No.
ANGLE
UNIT
QTY.
3,000
mm
ABLIC Inc.
Disclaimers (Handling Precautions)
1. All the information described herein (product data, specifications, figures, tables, programs, algorithms and application
circuit examples, etc.) is current as of publishing date of this document and is subject to change without notice.
2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not responsible for damages caused by the reasons other than the products described herein
(hereinafter "the products") or infringement of third-party intellectual property right and any other right due to the use
of the information described herein.
3. ABLIC Inc. is not responsible for damages caused by the incorrect information described herein.
4. Be careful to use the products within their specified ranges. Pay special attention to the absolute maximum ratings,
operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not responsible for damages caused by failures and / or accidents, etc. that occur due to the use of the
products outside their specified ranges.
5. When using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6. When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7. The products must not be used or provided (exported) for the purposes of the development of weapons of mass
destruction or military use. ABLIC Inc. is not responsible for any provision (export) to those whose purpose is to
develop, manufacture, use or store nuclear, biological or chemical weapons, missiles, or other military use.
8. The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses. Do
not apply the products to the above listed devices and equipments without prior written permission by ABLIC Inc.
Especially, the products cannot be used for life support devices, devices implanted in the human body and devices
that directly affect human life, etc.
Prior consultation with our sales office is required when considering the above uses.
ABLIC Inc. is not responsible for damages caused by unauthorized or unspecified use of our products.
9. Semiconductor products may fail or malfunction with some probability.
The user of the products should therefore take responsibility to give thorough consideration to safety design including
redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing injury or
death, fires and social damage, etc. that may ensue from the products' failure or malfunction.
The entire system must be sufficiently evaluated and applied on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc.
The information described herein does not convey any license under any intellectual property rights or any other
rights belonging to ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any
part of this document described herein for the purpose of disclosing it to a third-party without the express permission
of ABLIC Inc. is strictly prohibited.
14. For more details on the information described herein, contact our sales office.
2.2-2018.06
www.ablic.com
相关型号:
©2020 ICPDF网 联系我们和版权申明