AL-33-01SUG5C [A-BRIGHT]
High Power-LED Lamps; 高功率LED灯
| 型号： | AL-33-01SUG5C |
| 厂家： | 
A-BRIGHT INC |
| 描述： | High Power-LED Lamps |
| 文件： | 总6页 (文件大小：292K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
Part No.
3 mm
AL-33-01SUG5C
Diff No.
Type：
High Power
LED Lamps
Package Dimension:
Notes:
1. All dimensions are in millimeter.
2. An epoxy meniscus may extend about.
1.5mm(0.059") down to the lead
3. Tolerances unless Dimension ±0.25mm.
1
2009/3/23
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
Part No.
3 mm
AL-33-01SUG5C
Diff No.
Type：
High Power
LED Lamps
Chip
LED Parts P/N.
Lens Color
Material
Emitted Color
AL-33-01SUG5C
InGaN
Super Green
Water Clear
Absolute Maximum Ratings at Ta=25℃
Parameter
Continuous Forward Current
Operating Temperature
Storage Temperature
Soldering Temperature
Electrostatic Discharge
Power Dissipation
Symbol
IF
Rating
20
Unit
mA
℃
Topr
Tstg
Tsol
ESD
PD
-30 to +80
-40 to +100
260 ± 5
1000
℃
℃
V
120
mW
Peak Forward Current
（Duty 1/10@1KHz）
IF（Peak）
100
5
mA
V
Reverse Voltage
VR
Electronic Optical Characteristics :
Parameter
Luminous Intensity
Viewing Angle
Symbol Min. Typ. Max. Unit Condition
／
／
／
IV
3500
50
mcd IF=20mA
2θ1/2 ／
deg
nm
nm
nm
V
- - -
λp
λd
／
／
／
Peak Wavelength
530
525
30
IF=20mA
IF=20mA
IF=20mA
IF=20mA
VR=5V
／
Dominant Wavelength
Spectrum Radiation Bandwidth
Forward Voltage
△λ ／
／
／
VF
IR
3.2
4.0
50
／ ／
Reverse Current
μA
2
2009/3/23
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
Part No.
3 mm
AL-33-01SUG5C
Diff No.
Type：
High Power
LED Lamps
Reliability test items and conditions :
The reliability of products shall be satisfied with items listed below.
Confidence level: 90%
LTPD: 10%
Test
Sample
NO
ITEM
Test Conditions
Ac/Re
hours/cycle Q’ty
Temp：260℃±5℃
H：+85℃ 30min
5min
1 Solder Heat
5 sec
80 pcs 0/1
0/1
2 Temperature Cycle
3 Thermal Shock
100 cycles 80 pcs
L：-40℃ 30min
H：+100℃ 5min
10sec
0/1
100 cycles 80 pcs
L：-10℃ 5min
Ta=100℃
4 High Temperature Storage
5 Low Temperature Storage
1000 hrs 80 pcs 0/1
1000 hrs 80 pcs 0/1
Ta=-40℃
Temp：25℃
6 DC Operating Life
1000 hrs 80 pcs 0/1
1000 hrs 80 pcs 0/1
IF=20mA
High Temperature／
85℃／85%RH
7
High Humidity
3
2009/3/23
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
Part No.
3 mm
AL-33-01SUG5C
Diff No.
Type：
High Power
LED Lamps
4
2009/3/23
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
Part No.
3 mm
AL-33-01SUG5C
Diff No.
Type：
High Power
LED Lamps
5
2009/3/23
A-BRIGHT
A-BRIGHT INDUSTRIAL CO., LTD.
Part No.
3 mm
AL-33-01SUG5C
Diff No.
Type：
High Power
LED Lamps
Precautions For Use
1. Over-current proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change (Burn out will happen).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded
the storage time, baking treatment should be performed using the following conditions.
Baking treatment︰60±5℃for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 280℃for 3
seconds within once in less than soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the damage of the product
is often started at the time of the hand solder.
6
2009/3/23
相关型号：
©2020 ICPDF网 联系我们和版权申明