TP2122 [3PEAK]
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps;型号: | TP2122 |
厂家: | 3PEAK |
描述: | 1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps |
文件: | 总18页 (文件大小:606K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Features
Description
The TP212x are ultra-low power, precision CMOS
op-amps featuring a maximum supply current of
950nA per amplifier with an ultra-low typical input
bias current of 1fA. Analog trim and calibration
routine reduce input offset voltage to below 1.5mV,
and the precision temperature compensation
technique makes offset voltage temperature drift at
0.5μV/°C, which allowing use of the TP212x in
systems with high gain without creating excessively
Supply Current: 950nA Maximum /Amplifier
Stable 18kHz GBWP with 10mV/μs Slew Rate
Offset Voltage: 1.5mV Maximum
Ultra-low VOS TC: 0.5μV/°C
Ultra-low Input Bias Current: 1fA Typical
High 120dB Open-Loop Voltage Gain
Unity Gain Stable for 1,000nF Capacitive Load
Rail-to-Rail Input/Output Voltage Range
Outputs Source and Sink 20mA of Load Current
No Phase Reversal for Overdriven Inputs
Ultra-low Single-Supply Operation Down to +1.8V
Shutdown Current: 3nA Typical (TP2121N)
–40°C to 125°C Operation Range
large output offset errors.
The TP212x are unity gain stable with 1,000nF
capacitive load with a constant 18kHz GBWP,
10mV/μs slew rate, which make them appropriate
for low frequency applications, such as battery
current monitoring and sensor conditioning. The
TP212x can operate from a single-supply voltage of
+1.8V to +6.0V or a dual-supply voltage of ±0.9V to
±3.0V. Beyond the rails input and rail-to-rail output
characteristics allow the full power-supply voltage to
be used for signal range.
Robust 8kV – HBM and 2kV – CDM ESD Rating
Green, Popular Type Package
The combined features make the TP212x ideal
choices for battery-powered applications because
they minimize errors due to power supply voltage
variations over the lifetime of the battery and
maintain high CMRR even for a rail-to-rail input
op-amp. Mobile accessories, wireless remote
sensing, backup battery sensors, and single-Li+ or
2-cell NiCd/Alkaline battery powered systems can
benefit from the features of the TP212x op-amps.
Applications
Handsets and Mobile Accessories
Current Sensing
Wireless Remote Sensors, Active RFID Readers
Environment/Gas/Oxygen Sensors
Threshold Detectors/Discriminators
Low Power Filters
For applications that require power-down, the
TP2121N has a low-power shutdown mode that
reduces supply current to 3nA, and forces the output
into a high-impedance state.
Battery or Solar Powered Devices
Sensor Network Powered by Energy Scavenging
3PEAK and the 3PEAK logo are registered trademarks of
3PEAK INCORPORATED. All other trademarks are the property
of their respective owners.
Ultra-low Supply Current Op-amps:
Supply Current
GBWP
0.3 μA
0.6 μA
4 μA
10 kHz
18 kHz
150 kHz
TP1511
Single
TP2111
TP2121
With Shut-down TP2111N TP2121N TP1511N
Dual
TP2112
TP2114
TP2122
TP2124
TP1512
TP1514
Quad
R
1
VOUT ICC R3 ( 1)
R2
TP2121 in Low Side Battery Current Sensor
www.3peakic.com
REV1.2
1
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Pin Configuration(Top View)
Order Information
Marking
Information
Model Name
Order Number
Package
Transport Media, Quantity
TP2121-TR
TP2121-CR
TP2121-SR
TP2121U-TR
TP2121N-TR
TP2121N-VR
TP2121N-SR
TP2122-SR
TP2122-VR
TP2124-SR
TP2124-TR
5-Pin SOT23
5-Pin SC70
8-Pin SOIC
5-Pin SOT23
6-Pin SOT23
8-Pin MSOP
8-Pin SOIC
8-Pin SOIC
8-Pin MSOP
14-Pin SOIC
14-Pin TSSOP
Tape and Reel, 3,000
Tape and Reel, 3,000
Tape and Reel, 4,000
Tape and Reel, 3,000
Tape and Reel, 3,000
Tape and Reel, 3,000
Tape and Reel, 4,000
Tape and Reel, 4,000
Tape and Reel, 3,000
Tape and Reel, 2,500
Tape and Reel, 3,000
B2TYW (1)
B2CYW (1)
2121S
B2UYW (1)
B2NYW (1)
2121N
TP2121
TP2121U
TP2121N
2121NS
B22S
TP2122
TP2124
B22V
B24S
B24T
Note (1): ‘YW’ is date coding scheme. 'Y' stands for calendar year, and 'W' stands for single workweek coding scheme.
Note 1
Absolute Maximum Ratings
Supply Voltage: V+ – V–....................................6.0V
Input Voltage............................. V– – 0.3 to V+ + 0.3
Input Current: +IN, –IN, SHDN Note 2.............. ±10mA
SHDN Pin Voltage……………………………V– to V+
Output Current: OUT.................................... ±20mA
Output Short-Circuit Duration Note 3…......... Indefinite
Operating Temperature Range.......–40°C to 125°C
Maximum Junction Temperature................... 150°C
Storage Temperature Range.......... –65°C to 150°C
Lead Temperature (Soldering, 10 sec) ......... 260°C
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum
Rating condition for extended periods may affect device reliability and lifetime.
Note 2: The inputs are protected by ESD protection diodes to each power supply. If the input extends more than 500mV beyond the power supply, the input
current should be limited to less than 10mA.
REV1.2
www.3peakic.com
2
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Note 3: A heat sink may be required to keep the junction temperature below the absolute maximum. This depends on the power supply voltage and how many
amplifiers are shorted. Thermal resistance varies with the amount of PC board metal connected to the package. The specified values are for short traces
connected to the leads.
ESD, Electrostatic Discharge Protection
Symbol
HBM
Parameter
Human Body Model ESD
Charged Device Model ESD
Condition
Minimum Level
Unit
kV
kV
MIL-STD-883H Method 3015.8
JEDEC-EIA/JESD22-C101E
8
2
CDM
www.3peakic.com
REV1.2
3
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
5V Electrical Characteristics
The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 27°C.
VSUPPLY = 5V, VCM = VOUT = VSUPPLY/2, RL = 100kΩ, CL =60pF, VSHDN is unconnected.
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VOS
Input Offset Voltage
VCM = VDD/2 and VCM = GND
●
-1.5
±0.1
+1.5
mV
VOS TC
Input Offset Voltage Drift
0.5
1
700
45
μV/°C
fA
TA=27 oC
TA=85 oC
TA=125 oC
IB
Input Bias Current
fA
pA
IOS
Vn
en
Input Offset Current
Input Voltage Noise
Input Voltage Noise Density
Input Resistance
1
fA
f = 0.1Hz to 10Hz
f = 1kHz
6.5
170
> 1
2.9
5
μVP-P
nV/√Hz
TΩ
RIN
Differential
Common Mode
VCM = 0.1V to 4.9V
CIN
Input Capacitance
pF
dB
V
CMRR
VCM
Common Mode Rejection Ratio
Common-mode Input Voltage
Range
●
●
80
130
V––0.3
V++0.3
PSRR
AVOL
Power Supply Rejection Ratio
●
●
●
60
80
80
92
120
120
5
0.4
2.6
20
dB
dB
dB
mV
Ω
Ω
mA
V
V
OUT = 2.5V, RLOAD = 100kΩ
Open-Loop Large Signal Gain
VOUT = 0.1V to 4.9V, RLOAD = 100kΩ
RLOAD = 100kΩ
G = 1, f = 1kHz, IOUT = 0
f = 1kHz, IOUT = 0
VOL, VOH
ROUT
RO
ISC
VDD
Output Swing from Supply Rail
Closed-Loop Output Impedance
Open-Loop Output Impedance
Output Short-Circuit Current
Supply Voltage
Sink or source current
1.8
6.0
IQ
PM
GM
GBWP
Quiescent Current per Amplifier
Phase Margin
Gain Margin
●
600
61
-10
950
nA
°
dB
kHz
RLOAD = 100kΩ, CLOAD = 60pF
RLOAD = 100kΩ, CLOAD = 60pF
f = 1kHz
Gain-Bandwidth Product
18
Settling Time, 1.5V to 3.5V, Unity 0.1%
0.25
0.253
0.035
0.038
Gain
0.01%
tS
ms
Settling Time, 2.45V to 2.55V,
Unity Gain
0.1%
0.01%
AV = 1, VOUT = 1.5V to 3.5V, CLOAD
60pF, RLOAD = 100kΩ
2VP-P
=
SR
Slew Rate
10
mV/μs
FPBW
IQ(off)
Full Power Bandwidth Note 2
Supply Current in Shutdown Note 1
600
3
Hz
nA
VSHDN = 0.5V
-10
-10
-3.6
3.6
ISHDN
ILEAK
Shutdown Pin Current Note 1
pA
pA
VSHDN = 1.5V
Output Leakage Current in
Shutdown Note 1
SHDN Input Low Voltage Note 1
SHDN Input High Voltage Note 1
VSHDN = 0V, VOUT = 0V
VSHDN = 0V, VOUT = 5V
Disable
VIL
VIH
●
●
0.5
V
V
Enable
1.0
Note 1: Specifications apply to the TP2121N with shutdown.
Note 2: Full power bandwidth is calculated from the slew rate FPBW = SR/π • VP-P.
REV1.2
www.3peakic.com
4
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Typical Performance Characteristics
Small-Signal Step Response, 100mV Step
Large-Signal Step Response, 2V Step
Gain = +1
VIN Step = 100mV
CLOAD = 60pF
Gain = +1
CLOAD = 60pF
RLOAD = 100kΩ
Open-Loop Gain and Phase
Phase Margin vs. CLOAD (Stable for Any CLOAD)
Gain = +1
RLOAD = 100k
Ω
Phase
Gain
Gain = 1
RLOAD = 100k
CLOAD = 60pF
Ω
Input Voltage Noise Spectral Density
Common-Mode Rejection Ratio
www.3peakic.com
REV1.2
5
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Typical Performance Characteristics
Over-Shoot Voltage, CLOAD = 40nF, Gain = +1, RFB=100kΩ
Over-Shoot % vs. CLOAD, Gain = +1, RFB = 1MΩ
Gain = +1
VIN Step = 200mV
Overshoot
Gain = +1
VIN Step = 100mV
CLOAD = 40nF
Undershoot
Over-Shoot Voltage, CLOAD=40nF, Gain= -1, RFB=100kΩ
Over-Shoot % vs. CLOAD, Gain = -1, RFB = 1MΩ
Gain = -1
VIN Step = 200mV
Undershoot
Gain = -1
IN Step = 100mV
CLOAD = 40nF
V
Overshoot
Power-Supply Rejection Ratio
VIN = -0.2V to 5.7V, No Phase Reversal
PSRRP
PSRRN
REV1.2
www.3peakic.com
6
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Typical Performance Characteristics
Quiescent Supply Current vs. Temperature
Open-Loop Gain vs. Temperature
Quiescent Supply Current vs. Supply Voltage
Short-Circuit Current vs. Supply Voltage
30
25
20
15
10
5
750.0
700.0
85OC
650.0
27OC
600.0
550.0
500.0
450.0
400.0
-40OC
0
1.8
2.8
3.8
4.8
1.8
2.6
3.4
4.2
5
POWER SUPPLY VOLTAGE (V)
POWER SUPPLY VOLTAGE (V)
Input Offset Voltage Distribution
Input Offset Voltage vs. Common Mode Input Voltage
0.4
Production Package Units
V
DD=5V, VCM<VDD‐1V,
2000 Samples
0.3
TA = - 40OC
TA = +85OC
TA = +27OC
0.2
0.1
0
-0.1
0
1
2
3
4
5
Common Mode Input Voltage(V)
www.3peakic.com
REV1.2
7
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Typical Performance Characteristics
Closed-Loop Output Impedance vs. Frequency
0.1Hz to 10Hz Time Domain Output Voltage Noise
Pin Functions
–
–IN: Inverting Input of the Amplifier. Voltage range of
V– or VS: Negative Power Supply. It is normally
tied to ground. It can also be tied to a voltage other
than ground as long as the voltage between V+ and
V– is from 1.8V to 5.5V. If it is not connected to
ground, bypass it with a capacitor of 0.1μF as close
to the part as possible.
this pin can go from V– – 0.3V to V+ + 0.3V.
+IN: Non-Inverting Input of Amplifier. This pin has the
same voltage range as –IN.
V+ or +VS: Positive Power Supply. Typically the voltage
is from 1.8V to 5.5V. Split supplies are possible as long
as the voltage between V+ and V– is between 1.8V and
5.5V. A bypass capacitor of 0.1μF as close to the part as
possible should be used between power supply pins or
between supply pins and ground.
SHDN: Active Low Shutdown. Shutdown threshold
is 1.0V above negative supply rail. If unconnected,
the amplifier is automatically enabled.
OUT: Amplifier Output. The voltage range extends
to within milli-volts of each supply rail.
N/C: No Connection.
Operation
The TP212x family input signal range extends beyond
the negative and positive power supplies. The output
can even extend all the way to the negative supply. The
input stage is comprised of two CMOS differential
amplifiers, a PMOS stage and NMOS stage that are
active over different ranges of common mode input
voltage. The Class-AB control buffer and output bias
stage uses a proprietary compensation technique to
take full advantage of the process technology to drive
very high capacitive loads. This is evident from the
transient over shoot measurement plots in the Typical
Performance Characteristics.
REV1.2
www.3peakic.com
8
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Applications Information
Low Supply Voltage and Low Power Consumption
The TP212x family of operational amplifiers can operate with power supply voltages from 1.8V to 6.0V. Each amplifier
draws only 600nA quiescent current. The low supply voltage capability and low supply current are ideal for portable
applications demanding HIGH CAPACITIVE LOAD DRIVING CAPABILITY and CONSTANT WIDE BANDWIDTH. The
TP212x family is optimized for wide bandwidth low power applications. They have an industry leading high GBWP to
power ratio and are unity gain stable for 1,000nF capacitive load. When the load capacitance increases, the increased
capacitance at the output pushed the non-dominant pole to lower frequency in the open loop frequency response,
lowering the phase and gain margin. Higher gain configurations tend to have better capacitive drive capability than
lower gain configurations due to lower closed loop bandwidth and hence higher phase margin.
Low Input Referred Noise
The TP212x family provides a low input referred noise density of 170nV/√Hz at 1kHz. The voltage noise will grow
slowly with the frequency in wideband range, and the input voltage noise is typically 6.5μVP-P at the frequency of 0.1Hz
to 10Hz.
Low Input Offset Voltage
The TP212x family has a low offset voltage of 1.5mV maximum which is essential for precision applications. The offset
voltage is trimmed with a proprietary trim algorithm to ensure low offset voltage for precision signal processing
requirement.
Low Input Bias Current
The TP212x family is a CMOS OPA family and features very low input bias current in pA range. The low input bias
current allows the amplifiers to be used in applications with high resistance sources. Care must be taken to minimize
PCB Surface Leakage. See below section on “PCB Surface Leakage” for more details.
PCB Surface Leakage
In applications where low input bias current is critical, Printed Circuit Board (PCB) surface leakage effects need to be
considered. Surface leakage is caused by humidity, dust or other contamination on the board. Under low humidity
conditions, a typical resistance between nearby traces is 1012Ω. A 5V difference would cause 5pA of current to flow,
which is greater than the TP212x OPA’s input bias current at +27°C (±1fA, typical). It is recommended to use
multi-layer PCB layout and route the OPA’s -IN and +IN signal under the PCB surface.
The effective way to reduce surface leakage is to use a guard ring around sensitive pins (or traces). The guard ring is
biased at the same voltage as the sensitive pin. An example of this type of layout is shown in Figure 1 for Inverting
Gain application.
1. For Non-Inverting Gain and Unity-Gain Buffer:
a) Connect the non-inverting pin (VIN+) to the input with a wire that does not touch the PCB surface.
b) Connect the guard ring to the inverting input pin (VIN–). This biases the guard ring to the Common Mode input voltage.
2. For Inverting Gain and Trans-impedance Gain Amplifiers (convert current to voltage, such as photo detectors):
a) Connect the guard ring to the non-inverting input pin (VIN+). This biases the guard ring to the same reference voltage as
the op-amp (e.g., VDD/2 or ground).
b) Connect the inverting pin (VIN–) to the input with a wire that does not touch the PCB surface.
Figure 1
Ground Sensing and Rail to Rail Output
The TP212x family has excellent output drive capability, delivering over 10mA of output drive current. The output stage
is a rail-to-rail topology that is capable of swinging to within 5mV of either rail. Since the inputs can go 300mV beyond
either rail, the op-amp can easily perform ‘true ground’ sensing.
www.3peakic.com
REV1.2
9
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
The maximum output current is a function of total supply voltage. As the supply voltage to the amplifier increases, the
output current capability also increases. Attention must be paid to keep the junction temperature of the IC below 150°C
when the output is in continuous short-circuit. The output of the amplifier has reverse-biased ESD diodes connected to
each supply. The output should not be forced more than 0.5V beyond either supply, otherwise current will flow through
these diodes.
ESD
The TP212x family has reverse-biased ESD protection diodes on all inputs and output. Input and out pins can not be
biased more than 300mV beyond either supply rail.
Shut-down
The single channel OPA versions have SHDN pins that can shut down the amplifier to typical 3nA supply current. The
SHDN pin voltage needs to be within 0.5V of V– for the amplifier to shut down. During shutdown, the output will be in
high output resistance state, which is suitable for multiplexer applications. When left floating, the SHDN pin is internally
pulled up to the positive supply and the amplifier remains enabled.
Driving Large Capacitive Load
The TP212x family of OPA is designed to drive large capacitive loads. Refer to Typical Performance Characteristics
for “Phase Margin vs. Load Capacitance”. As always, larger load capacitance decreases overall phase margin in a
feedback system where internal frequency compensation is utilized. As the load capacitance increases, the feedback
loop’s phase margin decreases, and the closed-loop bandwidth is reduced. This produces gain peaking in the
frequency response, with overshoot and ringing in output step response. The unity-gain buffer (G = +1V/V) is the most
sensitive to large capacitive loads.
When driving large capacitive loads with the TP212x OPA family (e.g., > 200 pF when G = +1V/V), a small series
resistor at the output (RISO in Figure 2) improves the feedback loop’s phase margin and stability by making the output
load resistive at higher frequencies.
Figure 2
Power Supply Layout and Bypass
The TP212x OPA’s power supply pin (VDD for single-supply) should have a local bypass capacitor (i.e., 0.01μF to
0.1μF) within 2mm for good high frequency performance. It can also use a bulk capacitor (i.e., 1μF or larger) within
100mm to provide large, slow currents. This bulk capacitor can be shared with other analog parts.
Ground layout improves performance by decreasing the amount of stray capacitance and noise at the OPA’s inputs
and outputs. To decrease stray capacitance, minimize PC board lengths and resistor leads, and place external
components as close to the op amps’ pins as possible.
Proper Board Layout
To ensure optimum performance at the PCB level, care must be taken in the design of the board layout. To avoid
leakage currents, the surface of the board should be kept clean and free of moisture. Coating the surface creates a
barrier to moisture accumulation and helps reduce parasitic resistance on the board.
Keeping supply traces short and properly bypassing the power supplies minimizes power supply disturbances due to
output current variation, such as when driving an ac signal into a heavy load. Bypass capacitors should be connected
as closely as possible to the device supply pins. Stray capacitances are a concern at the outputs and the inputs of the
amplifier. It is recommended that signal traces be kept at least 5mm from supply lines to minimize coupling.
A variation in temperature across the PCB can cause a mismatch in the Seebeck voltages at solder joints and other
points where dissimilar metals are in contact, resulting in thermal voltage errors. To minimize these thermocouple
effects, orient resistors so heat sources warm both ends equally. Input signal paths should contain matching numbers
and types of components, where possible to match the number and type of thermocouple junctions. For example,
dummy components such as zero value resistors can be used to match real resistors in the opposite input path.
REV1.2
www.3peakic.com
10
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Matching components should be located in close proximity and should be oriented in the same manner. Ensure leads
are of equal length so that thermal conduction is in equilibrium. Keep heat sources on the PCB as far away from
amplifier input circuitry as is practical.
The use of a ground plane is highly recommended. A ground plane reduces EMI noise and also helps to maintain a
constant temperature across the circuit board.
BATTERY CURRENT SENSING
The Common Mode Input voltage Range of TP212x OPA series, which goes 0.3V beyond both supply rails, supports
their use in high-side and low-side battery current sensing applications. The low quiescent current (600nA, typical)
helps prolong battery life, and the rail-to-rail output supports detection of low currents.
The battery current (IDD) through the 10Ω resistor causes its top terminal to be more negative than the bottom terminal.
This keeps the Common Mode Input voltage below VDD, which is within its allowed range. The output of the OPA will
also be blow VDD, within its Maximum Output Voltage Swing specification.
VDD VOUT
IDD
R1
R3
R2
Figure 3
Instrumentation Amplifier
The TP212x OPA series is well suited for conditioning sensor signals in battery-powered applications. Figure 4 shows
a two op-amp instrumentation amplifier, using the TP212x OPA.
The circuit works well for applications requiring rejection of Common Mode noise at higher gains. The reference
voltage (VREF) is supplied by a low-impedance source. In single voltage supply applications, VREF is typically VDD/2.
R
2R
1 ) VREF
R2 RG
1
VOUT =(V V2 )(1
1
Figure 4
Buffered Chemical Sensor (pH) Probe
The TP212x OPA has input bias current in the pA range. This is ideal in buffering high impedance chemical sensors
such as pH probe. As an example, the circuit in Figure 5 eliminates expansive low-leakage cables that that is
required to connect pH probe to metering ICs such as ADC, AFE and/or MCU. A TP212x OPA and a lithium battery
are housed in the probe assembly. A conventional low-cost coaxial cable can be used to carry OPA’s output signal to
subsequent ICs for pH reading.
www.3peakic.com
REV1.2
11
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Figure 5: Buffer pH Probe
Portable Gas Sensor Amplifier
Gas sensors are used in many different industrial and medical applications. Gas sensors generate a current that is
proportional to the percentage of a particular gas concentration sensed in an air sample. This output current flows
through a load resistor and the resultant voltage drop is amplified. Depending on the sensed gas and sensitivity of the
sensor, the output current can be in the range of tens of microamperes to a few milli-amperes. Gas sensor datasheets
often specify a recommended load resistor value or a range of load resistors from which to choose.
There are two main applications for oxygen sensors – applications which sense oxygen when it is abundantly present
(that is, in air or near an oxygen tank) and those which detect traces of oxygen in parts-per-million concentration. In
medical applications, oxygen sensors are used when air quality or oxygen delivered to a patient needs to be monitored.
In fresh air, the concentration of oxygen is 20.9% and air samples containing less than 18% oxygen are considered
dangerous. In industrial applications, oxygen sensors are used to detect the absence of oxygen; for example,
vacuum-packaging of food products.
The circuit in Figure 6 illustrates a typical implementation used to amplify the output of an oxygen detector. With the
components shown in the figure, the circuit consumes less than 600nA of supply current ensuring that small
form-factor single- or button-cell batteries (exhibiting low mAh charge ratings) could last beyond the operating life of
the oxygen sensor. The precision specifications of these amplifiers, such as their low offset voltage, low VOS TC, low
input bias current, high CMRR, and high PSRR are other factors which make these amplifiers excellent choices for this
application.
I
O2
VOUT 1Vin Air ( 21% O2 )
IDD 0.7uA
Figure 6
REV1.2
www.3peakic.com
12
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Package Outline Dimensions
SOT23-5 / SOT23-6
Dimensions
Dimensions
In Inches
In Millimeters
Symbol
Min
Max
Min
Max
A1
A2
b
0.000
1.050
0.300
2.820
1.500
2.650
0.100
1.150
0.400
3.020
1.700
2.950
0.000
0.041
0.012
0.111
0.059
0.104
0.004
0.045
0.016
0.119
0.067
0.116
D
E
E1
e
0.950TYP
0.037TYP
e1
L1
θ
1.800
0.300
0°
2.000
0.460
8°
0.071
0.012
0°
0.079
0.024
8°
www.3peakic.com
REV1.2
13
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Package Outline Dimensions
SC-70-5 / SC-70-6 (SOT353 / SOT363)
Dimensions
Dimensions In
Inches
In Millimeters
Symbol
Min
Max
Min
Max
A1
A2
b
0.000
0.900
0.150
0.080
2.000
1.150
2.150
0.100
1.000
0.350
0.150
2.200
1.350
2.450
0.000
0.035
0.006
0.003
0.079
0.045
0.085
0.004
0.039
0.014
0.006
0.087
0.053
0.096
C
D
E
E1
e
0.650TYP
0.026TYP
e1
L1
θ
1.200
0.260
0°
1.400
0.460
8°
0.047
0.010
0°
0.055
0.018
8°
REV1.2
www.3peakic.com
14
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Package Outline Dimensions
SO-8 (SOIC-8)
A2
C
θ
L1
A1
e
E
D
Dimensions
Dimensions In
Inches
In Millimeters
Symbol
Min
Max
Min
Max
A1
A2
b
0.100
1.350
0.330
0.190
4.780
3.800
5.800
0.250
1.550
0.510
0.250
5.000
4.000
6.300
0.004
0.053
0.013
0.007
0.188
0.150
0.228
0.010
0.061
0.020
0.010
0.197
0.157
0.248
E1
C
D
E
E1
e
1.270TYP
0.050TYP
L1
θ
0.400
0°
1.270
8°
0.016
0°
0.050
8°
b
Package Outline Dimensions
www.3peakic.com
REV1.2
15
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
MSOP-8
Dimensions
Dimensions In
Inches
In Millimeters
Symbol
Min
Max
Min
Max
E
A
0.800
0.000
0.760
0.30 TYP
0.15 TYP
2.900
0.65 TYP
2.900
4.700
0.410
0°
1.200
0.200
0.970
0.031
0.000
0.030
0.012 TYP
0.006 TYP
0.114
0.026
0.114
0.185
0.016
0°
0.047
0.008
0.038
E1
A1
A2
b
C
D
3.100
0.122
e
b
e
E
3.100
5.100
0.650
6°
0.122
0.201
0.026
6°
D
E1
L1
θ
A1
R1
R
θ
L
L1
L2
REV1.2
www.3peakic.com
16
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Package Outline Dimensions
SO-14 (SOIC-14)
Dimensions
In Millimeters
TYP
Symbol
MIN
1.35
0.10
1.25
0.36
8.53
5.80
3.80
MAX
1.75
0.25
1.65
0.49
8.73
6.20
4.00
A
A1
A2
b
1.60
0.15
1.45
D
8.63
6.00
E
E1
e
3.90
1.27 BSC
0.60
L
0.45
0°
0.80
8°
L1
L2
θ
1.04 REF
0.25 BSC
www.3peakic.com
REV1.2
17
TP2121/TP2121N/TP2122/TP2124
1.8V, 600nA Nanopower, Rail-to-Rail Input/Output Op-amps
Package Outline Dimensions
TSSOP-14
Dimensions
In Millimeters
E1
E
Symbol
MIN
-
TYP
MAX
1.20
0.15
1.05
0.28
0.19
5.06
6.60
4.50
A
A1
A2
b
-
0.05
0.90
0.20
0.10
4.86
6.20
4.30
-
1.00
-
e
c
c
-
4.96
D
D
E
6.40
E1
e
4.40
0.65 BSC
0.60
L
0.45
0.75
A1
L1
L2
R
1.00 REF
0.25 BSC
-
0.09
0°
-
R1
θ
-
8°
R
θ
L
L1
L2
REV1.2
www.3peakic.com
18
相关型号:
©2020 ICPDF网 联系我们和版权申明